Professional Documents
Culture Documents
Corporate Headquarters - San Jose, CA USA T: (408) 333-8000 info@brocade.com European Headquarters - Geneva, Switzerland T: +41 22 799 56 40 emea-info@brocade.com Asia Pacific Headquarters - Singapore T: +65-6538-4700 apac-info@brocade.com
2011 Brocade Communications Systems, Inc. All Rights Reserved. Brocade, the Brocade B-weave logo, Fabric OS, File Lifecycle Manager, MyView, Secure Fabric OS, SilkWorm, and StorageX are registered trademarks and the Brocade B-wing symbol and Tapestry are trademarks of Brocade Communications Systems, Inc., in the United States and/ or in other countries. FICON is a registered trademark of IBM Corporation in the U.S. and other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government. Revision 0511
Objective: The BCNE Nutshell guide is designed to help you prepare for the BCNE Certification, exam number 150-120. Audience: The BCNE Nutshell self-study guide is intended for those who have successfully completed the ETH 101 and 103 training courses, and who wish to undertake self-study or review activities before taking the actual BCNE exam. The BCNE guide is not intended as a substitute for classroom training or hands-on time with Brocade products. How to make the most of the BCNE guide: The BCNE guide summarizes the key topics on the BCNE exam for you in an easy to use format. It is organized closely around the exam objectives. We suggest this guide be used in conjunction with our free online knowledge assessment test, CNE 101-WBT BCNE Knowledge Assessment. To benefit from the BCNE guide, we strongly recommend you have successfully completed the Course# withFullName course. We hope you find this useful in your journey towards BCNE Certification, and we welcome your feedback by sending an email to jcannata@brocade.com.
ii
Table of Contents
1 - Layer 1 Hardware Concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Implementing Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Implementing Hardware Platforms and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 - Routing Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7 - Wireless Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Wireless Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
iii
9 - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Tools and Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Analyzing Troubleshooting Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
iv
List of Figures
SFP Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MAC Address OUI and Unique ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAC Address Inside an Ethernet Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Physical media cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 POE Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Per VLAN Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 802.1D STP Convergence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 STP Port States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Fast Port Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Basic MRP Single-ring Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 UDLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Switch Frame Forwarding Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Types of VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Private VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 VLAN Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 802.1Q Tagging (Packet Format) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Dual-mode VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Inter-VLAN Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Dynamic Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Ethernet Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 STP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Default Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 End-to-End Flow Example 1 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 End-to-End Flow Example 2 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 End-to-End Flow Example 3 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 End-to-End Flow Example 4 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 VRRP-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Multiple VRRP-E Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Subnetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 OSPF Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 OSPF AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 OSPF DR Election . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Redistribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 BGP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 BGP Peer Establishment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 BGP Route Advertisement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 IP Multicast Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Standard ACL Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Policy-based Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 802.11b Spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Management Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 CLI Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
vi
List of Tables
STP Port States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Default Administrative Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
vii
viii
SFP Transceivers
The Small Form-factor Pluggable (SFP) is a compact, hot-pluggable transceiver used for both telecommunication and data communication applications. It interfaces a network device motherboard (for a switch, router, media converter, or similar device) to a fiber optic or copper networking cable. It is a popular industry format. SFP transceivers are designed to support SONET, gigabit Ethernet (GbE), Fibre Channel (FC), and other communications standards. The standard covers SFP+ supporting data rates up to 10 Gbps (includes 8 Gbps Fibre Channel and 10 GbE). The SFP+ has the same form factor as a regular SFP. If copper is required 1000 Mbit TX SFPs could be used on non-combo ports.
The MAC address is used to uniquely identify each node on the Ethernet network
A MAC comprises 48 bits in 6 hex pairs: xx:xx:xx:yy:yy:yy - The first 3 bytes (xx:xx:xx) represent the manufacturers IEEE registered Organizational Unique
Identifier (OUI)
The last 3 bytes (yy:yy:yy) represent a unique ID (all NICs must be unique)
MAC addresses can also be notated by three sets of four nibbles: - 1234.5678.9abc The Destination Address (DA) and Source Address (SA) fields in an ethernet frame each contain a MAC
address
Cable Types
Coaxial - Thick - Thin Twisted Pair (TP) - Shielded (STP) - Unshielded (UTP) UTP is less expensive and less resistant to noise than STP Fiber Optic - Multi-mode - Single mode
Noise is unwanted signals, or interference, from sources near network cabling, such as electrical motors,
power lines and radar
Attenuation is the amount of signal loss over a given distance Crosstalk is a type of interference caused by signals traveling on nearby wire pairs infringing on another
pairs signal
Bend radius is the radius of the maximum arc into which you can loop a cable before you will cause
transmission errors
2011 Brocade Communications
3
Latency is the delay between the transmission of a signal and its receipt Jitter is a variation in packet transit delay caused by queuing, contention and serialization effects on the
path through the network
The following example displays the operational status: Switch_A# show inline power Power Capacity: Total is 2160000 mWatts. Current Free is 18800 mWatts. Power Allocations: Requests Honored 769 times <truncated> Port Admin Oper ---Power(mWatts)--PD Type PD Class Pri Fault/ State State Consumed Allocated Error -------------------------------------------------------------------------4/1 On On 5070 9500 802.3af n/a 2 n/a 4/2 On On 1784 9500 Legacy n/a 3 n/a 4/3 On On 2347 9500 802.3af n/a 3 n/a 4/4 On On 2441 9500 Legacy n/a 3 n/a 4/5 On On 6667 9500 802.3af Class 3 3 n/a 4/6 On On 2723 9500 802.3af Class 2 3 n/a <truncated> -------------------------------------------------------------------------Total 137367 242000 Grand Total 1846673 2127400
File Management
You can specify which partition to boot from using the boot system flash command. When to boot is specified by the level at which the command is issued. For example, issuing from the Privileged level causes the command to execute immediately: SW-Switch# boot system flash primary SW-Switch# boot system flash secondary Issuing from the Config level causes the command to execute at the next scheduled reload or reboot and allows for the command to be persistently stored in the startup configuration file: SW-Switch(config)# boot system flash secondary SW-Switch(config)# write memory SW-Switch(config)# exit SW-Switch# reload at 00:00:15 01-01-12 Besides the flash partitions, the system can be booted from either a TFTP server or a BootP server. The following command sequence examples is typed from the privileged exec level and boots the system from the TFTP server at 192.22.33.44 using the vm1r07501.bin file. SW-Switch# boot system tftp 192.22.33.44 vm1r07501.bin After booting from a TFTP server, the booted image file should be copied from the TFTP server to primary flash when the boot is completed, so that the next system boot maintains the current functions independent of the TFTP server connection.
The secondary partition of the flash card may be used as the storage space for upgrade code. If the image is on the TFTP server, the code may be transferred to the switchs flash card. Then the switch may be booted from the image stored on the flash card. The following command example transfers the image between the TFTP server and the flash card, from the privileged EXEC level: SW-Switch# copy tftp flash 192.22.33.44 vm1r07501.bin secondary Once copied to the switch, issue the reload command to reboot the switch using the new image: SW-Switch# reload
Describe Layer 2 protocols Describe Layer 2 functionality Describe the different VLAG implementations
Layer 2 Protocols
A protocol is a set of rules that governs the communications between computers on a network These rules include guidelines that regulate the following characteristics of a network:
Access method Allowed physical topologies Transport medium Speed of data transfer
Each VLAN has its own Spanning Tree instance Each VLAN has its own root bridge Ports blocked by one STP instance can be used by another STP instance
The switch with the lowest BID wins and becomes the Root Bridge. If Bridge Priorities are the same, the switch with the lowest MAC address wins and becomes the Root Bridge.
Root Bridge (Priority:0) Switch#1
00:0E:80:0A:F0:06
DP
DP
RP Switch#3
00:0E:80:01:90:06
RP DP Switch#2
00:0E:80:01:F0:06
(Priority:200)
(Priority:100)
Configuration BPDU
Generated only by the root bridge and sent to non-root bridges, it provides a method of providing election information across the L2 domains and controlls reconvergence after a link has been broken.
One switch is elected as the root switch The shortest distance to the root switch is calculated by each switch A designated switch is selected. This is the switch closest to the root switch through which user traffic/
frames will be forwarded to the root
A root port for each switch is selected. This is the port providing the best path from the switch to the root
switch
A designated port for each LAN segment is selected. This is the port providing the best path from the LAN
segment to the root switch.
Ports included in the Spanning-Tree Protocol are selected If all switches are enabled with default settings, the switch with the lowest MAC address in the network
becomes the root switch. The network assuming that Switch 1 has the lowest MAC address and is therefore the root switch. Due to traffic patterns, number of forwarding ports, or line types, Switch 1 might not be the ideal root switch. By increasing the priority (lowering the numerical priority number) of the ideal switch so that it then becomes the root switch, you force a Spanning-Tree Protocol recalculation to form a new, stable topology.
10
You can change the bridge priority, port priority, and path cost so that a predetermined outcome occurs in the election process (Learning state).
Port initialization Non Designated Ports: Port is Blocked MAC table remains empty Port Role is established as: Root Port Designated Port Non-Designated (15 sec) Root and Designated Ports: Port receives data traffic Populates its MAC table (15 sec) Root and Designated Ports: Send and Receive data traffic
Figure 8: STP Port States
Blocking state
Listening state
Learning state
Forwarding state
11
Fast Port Span performs the convergence on these ports in four seconds (two seconds for listening and two seconds for learning). In addition, Fast Port Span enhances overall network performance in the following ways:
Reduces the number of STP topology change notifications on the network Eliminates unnecessary MAC cache aging that can be caused by topology change notifications When STP sends a topology change notification, devices that receive the notification use the value of the
STP forward delay to quickly age out their MAC caches
If a port matches any of the following criteria, it port is ineligible for Fast Port Span and uses normal STP
instead:
The port is 802.1Q tagged (refer to 802.1Q Tagging on page17) The port is a member of a trunk group The port has learned more than one active MAC address An STP configuration BPDU has been received on the port, thus indicating the presence of another bridge on the port
Topology Groups
A topology group is a named set of VLANs that share a Layer 2 topology. Topology groups simplify configuration and enhance scalability of Layer 2 protocols by allowing you to run a single instance of a Layer 2 protocol on multiple VLANs. You can use topology groups with the following Layer 2 protocols:
Spanning Tree Protocol (STP) Multi-Ring Protocol (MRP) Virtual Switch Redundancy Protocol (VSRP) Rapid Spanning Tree Protocol (802.1w)
12
MRP (Metro Ring Protocol) is a Brocade proprietary protocol that prevents Layer 2 loops and provides fast reconvergence in Layer 2 ring topologies. It is an alternative to STP and is especially useful in Metropolitan Area Networks (MANs) where using STP has the following drawbacks:
STP allows a maximum of seven nodes. Metro rings can easily contain more nodes than this STP has a slow re-convergence time, taking many seconds or even minutes. MRP can detect and heal a
break in the ring in sub-second time A ring interface can have one of the following MRP states:
Preforwarding: The interface can forward Ring Health Packets (RHPs), but cannot forward data. All ring
ports are in this state when you enable MRP.
Forwarding: Each member interface remains in the Forwarding state Blocking: The Blocking interface on the Master node has a dead timer. If the dead time expires before the
interface receives one of its rings RHPs, the interface changes state to Preforwarding. One of the following occur once the secondary interface changes its state to Preforwarding:
If the interface receives an RHP, the interface changes back to the Blocking state and resets the dead timer. If the interface does not receive an RHP for its ring before the Preforwarding time expires, the interface changes to the Forwarding state If the link between shared interfaces breaks, the secondary interface on the master node changes to a Preforwarding state.
The ring in Figure10 consists of four MRP nodes (Brocade switches). Each node has two interfaces with the ring. Each node is also connected to a separate customer network. The nodes forward Layer 2 traffic to and from the customer networks through the ring. The ring interfaces are all in one port-based VLAN. Each customer interface can be in the same VLAN as the ring, or in a separate VLAN. One node is configured as the master node of the MRP ring. One of the two interfaces on the master node is configured as the primary interface; the other is the secondary interface. The primary interface originates Ring Health Packets (RHPs), which are used to monitor the health of the ring. An RHP is forwarded on the ring to the next interface until it reaches the secondary interface of the master node. The secondary interface blocks the packet to prevent a Layer 2 loop.
13
Layer 2 Functionality
Clearing MAC Address Entries
You can remove learned MAC address entries from the MAC address table. The types of MAC addresses that can be removed are:
All MAC address entries All MAC address entries for a specified Ethernet port All MAC address entries for a specified VLAN All specified MAC address entry in all VLANs
Running the clear mac-address command without any parameters will remove all MAC address entries.
14
Cut-through
The switch reads only up to the frame's hardware address before starting to forward it. There is no error checking with this method. Cut-through switching means that the switch copies into its memory only the destination MAC address, which is located in the first 6 bytes of the frame following the preamble. The switch looks up the destination MAC address in its forwarding table, determines the outgoing interface port, and forwards the frame on to its destination through the designated switch port. This method will not detect runt frames.
Fragment-free
Another alternative is Fragment-free switching, which works like cut-through switching with the exception that a switch in fragment-free mode stores the first 64 bytes of the frame before forwarding. This can be viewed as a hybrid/compromise between store-and-forward switching and cut-through switching. The reason fragment-free switching stores only the first 64 bytes of the frame is that most network errors and collisions occur within the first 64 bytes of a frame.
Creates a broadcast domain Done through software configuration Implemented in port switching, hubs and LAN switches
By default, all Brocade switch ports are members of VLAN 1. VLANs reduce the time it takes to implement moves, adds and changes. Layer 3 VLANs require that all members are in the same port-based VLAN.
15
Private VLANs
Platform support:
FastIron X Series devices running software release 02.4.00 and later FGS and FLS devices running software release FGS-STK and FLS-STK devices running software release 05.0.00 and later FWS devices running software release 04.3.00 and later
By default, a private VLAN does not forward broadcast or unknown-unicast packets from outside sources into the private VLAN. If needed, you can override this behavior for broadcast packets, unknown-unicast packets, or both. You can configure a combination of the following types of private VLANs:
Primary: The primary private VLAN ports are promiscuous. They can communicate with all the isolated
private VLAN ports and community private VLAN ports in the isolated and community VLANs that are mapped to the promiscuous port.
Isolated: Broadcasts and unknown unicasts received on isolated ports are sent only to the primary port.
They are not flooded to other ports in the isolated VLAN
16
Community: Broadcasts and unknown unicasts received on community ports are sent to the primary port
and also are flooded to the other ports in the community VLAN
Each private VLAN must have a primary VLAN. The primary VLAN is the interface between the secured ports and the rest of the network. The private VLAN can have any combination of community and isolated VLANs.
You cannot configure isolated, community, or primary VLANs on 802.1Q tagged ports Normally, in any port-based VLAN, the device floods unknown unicast, unregistered multicast, and
broadcast packets in hardware, although selective packets, such as IGMP, may be sent to only to the CPU for analysis, based on the IGMP snooping configuration.
When protocol or subnet VLANs, or private VLAN mappings are enabled, the device floods unknown
unicast, unregistered multicast, and broadcast packets in software
802.1Q Tagging
When you create a VLAN on a switch, you need to determine which of its ports participate in that VLAN. The two types of membership are:
Tagged the switch adds an extra 4 bytes to the Ethernet frame called the 802.1Q header - Allows multiple port based VLANs to span switches over a single physical link Untagged the switch keeps track of this port as a member of the VLAN
802.1Q tagging is an IEEE standard that allows a networking device to add information to a Layer 2 frame in order to identify its VLAN membership. A port can belong to only one port-based VLAN, unless 802.1Q tagging is applied to the port. 802.1Q tagging allows the port to add a four-byte field, which contains the VLAN ID, to each frame sent on the port. Port-based VLANs can also be configured to span multiple devices by tagging the ports within the VLAN. The tag enables each device that receives the frame to determine to which VLAN the frame belongs. 802.1Q tagging applies only to Layer 2 VLANs.
17
The tag contains the TPID, which identifies the frame as a tagged. The value of the TPID is 8100, and also contains the VLAN ID of the VLAN from which the packet is sent. The VLAN ID is determined by the VLAN on which the packet is being forwarded. There are also 3 bits reserved for the priority (802.1p), and the field type is 8100.
The following command sequence example configures VLAN and assigns an IP address to a VE for VLAN 14: NetIron(config)# vlan 14 NetIron(config-vlan-14)# untag ethernet 1/1 to 1/12 NetIron(config-vlan-14)# router-interface ve 1 NetIron(config-vlan-14)# exit NetIron(config)# interface ve1 NetIron(config-vif-1)# ip address 192.123.22.1 255.255.255.0
18
In Figure17, port e6 is running in dual mode. Port e6 has tagged membership in VLAN 20 and untagged membership in VLAN 10. The network includes an IP phone that typically has a two port switch built into it. One port on an IP phone has the 802.1q ability, and the other for untagged traffic. Thus, frames from both the PC and the phone travel between the phone and switch. The following command example explains how to configure the dual-mode port: Switch(config)# vlan 10 Switch(config-vlan-10)# tagged e6 Switch(config-vlan-10)# untagged e34 BigIron(config)# vlan 20 BigIron(config-vlan-20)# tagged e6 BigIron(config-vlan-20)# tagged e49 BigIron(config)# interface e6 BigIron(config-if-e100-6)# dual-mode 10 Following are a few rules to remember when configuring dual-mode VLANs:
You can configure private VLANs and dual-mode VLAN ports on the same device Dual-mode VLAN ports cannot be members of private VLANs
19
Based on the diagram shown in Figure18, the following command sequence is an example of how to configure inter-VLAN routing: FastIron(config)# vlan 10 FastIron(config-vlan-22)# untag ethernet 1 to 16 FastIron(config-vlan-22)# router-interface ve 1 FastIron(config)# interface ve1 FastIron(config-vif-1)# ip address 192.123.22.1/24 FastIron(config)# vlan 20 FastIron(config-vlan-44)# untag ethernet 33 to 48 FastIron(config-vlan-44)# router-interface ve 2 FastIron(config)# interface ve2 FastIron(config-vif-2)# ip address 192.123.44.1 255.255.255.0
20
Port tag type (tagged/untagged) Configured port speed3 and duplex QoS priority
Brocade switches support the use of static and dynamic LAGs on the same device4, but can use only one type of LAG for any given port.
In addition to traffic load sharing, trunk groups provide redundant, alternate paths for traffic if any of the segments fail.
1. Link Aggregation Groups are also referred to as: Ethernet trunk, NIC Teaming, Port Channel, Port Teaming, Port Trunking, Link Bundling, EtherChannel, Multi-Link Trunking (MLT), DMLT, SMLT, DSMLT, R-SMLT, NIC bonding, Network Fault Tolerance (NFT), and Fast EtherChannel. 2. Multi-Chassis Trunking is a technology that allows multiple switches to appear as a single logical switch connecting to another switch using a standard LAG. Since the technology is an enhancement to the standard LAG protocol, a single MCT-unaware server or switch using a standard LAG trunk can connect to two MCT-aware switches--and the traffic is dynamically load balanced. For more information on this topic, please refer to the FastIron Configuration Guide for the particular platform. 3. Each port in the LAG operates at the speed of the slowest link. For example, if one LAG is created with 2 ports and one is running at 10 Gbps and the other is running at 1 Gbps; each link operates at 1 Gbps. This behavior occurs if the ports are configured to auto and negotiate to different speeds. 4. Multiple LAGs can be created on a switch with some of them being static LAGs and some of them being dynamic LAGs. A single port can only be part of one LAG type.
21
Static trunking - Manually configured aggregate links containing multiple ports Dynamic Trunking: (802.3ad Link Aggregation) - Dynamically created and managed trunk groups using Link Aggregation Control Protocol (LACP)
Trunking can be established between Brocade Layer 2/3 switches, or between a switch and a server.
Dynamic Trunking
Brocade software supports the IEEE 802.3ad standard for link aggregation. This standard describes the Link Aggregation Control Protocol (LACP), a mechanism for allowing ports on both sides of a redundant link to form a trunk link (aggregate link), without the need for manual configuration of the ports into trunk groups. When you enable link aggregation on a group of Brocade ports, the Brocade ports can negotiate with the ports at the remote ends of the links to establish trunk groups. To display link aggregation information, including the key for all ports on which link aggregation is enabled, enter the following command at any level of the CLI: Switch(config)# show link-aggregation System ID 00e0.52a9.bb00 Port [sys P] [Port P] [Key] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope] 1/1 1 1 20 No L Agg Syn No No Def Exp Blo 1/2 1 1 20 No L Agg Syn No No Def Exp Blo 1/3 1 1 20 No L Agg Syn No No Def Exp Blo 1/4 1 1 20 No L Agg Syn No No Def Exp Ina 1/5 1 1 10 Yes L Agg No No No Def Exp Blo 1/6 1 1 10 Yes L Agg No No No Def Exp Blo 1/7 1 1 10 Yes L Agg No No No Def Exp Blo 1/8 1 1 10 Yes L Agg No No No Def Exp Ope Ope displays the operation state of the link. The following are blanks of operational states:
22
Key 20
Key 30
Key 10
Key 40
Switch 1
Switch 2
BigIron_A(config)# interface ethernet 1/1 BigIron_A(config-if-e1000-1/1)# link-aggregate active BigIron_A(config)# interface ethernet 1/2 BigIron_A(config-if-e1000-1/2)# link-aggregate active BigIron_B(config)# interface ethernet 1/1 to 1/2 BigIron_B(config-mif-1/1-1/2)# link-aggregate passive The active device sends and receives LACP Protocol Data Unit (LACPDU) messages; the passive device only receives LACPDUs.
23
Learn MAC addresses of nodes and their associated ports Filter incoming frames destined for nodes that are located on the same incoming port Forward incoming frames to known destinations through their associated ports; and if the frame is
unknown, it floods the unknown frames out on all ports belonging to that VLAN, except for the incoming port Use the show mac-address command to display the MAC address table FastIron# show mac-address Total active entries from all ports = 3 Total static entries from all ports = 1 MAC-Address 1234.1234.1234 0004.8038.2f24 0004.8038.2f00 0010.5a86.b159 Port 15 15 13 10 Type Static Dynamic Dynamic Dynamic VLAN 1 1 1 1
24
ARP is used to resolve MAC addresses for hosts on the local subnet; for remote destinations, the source host sends out ARP requests asking for the MAC address of the default gateway. If a node matches the requested IP, it sends back its MAC address. Other nodes discard the ARP request.
Multiple active paths between nodes cause loops in the network If a loop exists in the network topology, the potential exists for duplication of frame delivery When loops occur, switches may see the same node appear on different ports on the switch
The STP algorithm relies on the use of Bridge Protocol Data Units (BPDUs), which provide information to all switches about the distance in hops to each switch port from a root switch. By default, the switch with the lowest MAC address becomes the root bridge.
25
There is a configurable parameter (Bridge Priority) that can be set on each switch to allow administrators to predetermine a specific root bridge. Using BPDU information, a switch can determine whether one of its ports provides an optimal path to the root bridge. If it does not, that port is placed in the blocked state. If the path distance is optimal but is the same as another switches path, a simple method (atie breaker) allows one of the ports to be placed in blocked mode. If one network segment in the Spanning Tree Protocol becomes unreachable, or if a port cost changes, the spanning-tree algorithm reconfigures the spanning-tree topology and re-establishes the link by activating the standby path.
Traffic Types
Unicast traffic describes point to point communication where there is just one sender, and one receiver. Unicast transmission, in which a packet is sent from a single source to a specified destination, is still the predominant form of transmission on LANs and within the Internet. IP networks support the Unicast transfer mode, and most users are familiar with the standard unicast applications (e.g. HTTP, SMTP, FTP and Telnet) which employ the TCP transport protocol. Multicast traffic describes communication which occurs between a sender and a grouping of recipients. Multicasting is the networking technique of delivering the same packet simultaneously to a group of clients. One example of an application which may use multicast is a video server sending out networked TV channels. Broadcast traffic describes communication where a piece of information is sent from one point to all other points. In this case there is one sender and many receivers. An example of this is the ARP which uses a broadcast to send an address resolution query to all devices on a LAN segment in order to resolve an IP address to a physical MAC address. A host will drop the ARP if it is not the target of the request. ARPs are used to resolve unknown destination MAC addresses.
Routing
Routing is needed when data needs to reach a remote network that is not directly connected to the local router.
Explicit default route - IPv4 default route 0.0.0.0 0.0.0.0 or 0.0.0.0/0 - Can be a static route or learned dynamically by a routing protocol like OSPF. OSPF uses a command
called default-information originate to send the default route to other OSPF routers
Candidate default route - A Candidate default network is used when a default route is not statically configured or propagated by
a routing protocol
26
The command ip route 0.0.0.0 0.0.0.0 209.157.1.1 is a default route or route of last resort because it is last place in the order of execution of the route table. The ip route 0.0.0.0 0.0.0.0 209.157.1.1 can appear in a route table because it is:
Manually configured on the router Can be sent to other routesr by a routing protocol like OSPF The command ip default-network 209.157.1.0 is a default network route and is there in case
a default route is not present because it has neither been manually configured nor passed by routing protocol like OSPF The following ouput displays the 10.1.1.0/30 network is marked as the candidate default network with the asterisk * sign. This network is remote to Router_A and has been learned by Router_A through the routing protocol OSPF. That is why the Type field for the network 10.1.1.0 is marked as *O. Router_A(config)# show ip route Total number of IP routes: 6, avail: 79994 (out of max 80000) B:BGP D:Connected R:RIP S:Static O:OSPF *:Candidate default Destination NetMask Gateway Port 0.0.0.0 0.0.0.0 156.10.20.21 9 1 10.1.1.0 255.255.255.252 10.1.2.1 7 2 10.1.2.0 255.255.255.252 0.0.0.0 7 3 156.10.20.20 255.255.255.252 0.0.0.0 9 4 172.16.1.0 255.255.255.0 10.1.2.1 7 5 192.168.1.0 255.255.255.0 0.0.0.0 1
Cost 1 1 1 1 1 1
Type S *O D D S D
27
1. If the destination hosts network number was the same as the source hosts, then the destination host would be considered local and on the same subnet. This is determined by taking Host A taking its own IP address and subnet mask and determining its own network address and then doing the same operation with the destination IP and destinations subnet mask and comparing the results. If they are the same then the destination Host B would be considered local; Otherwise the packets will be forwarded to the default gateway in order to be sent to a remote host. In this example the destination Host Bs Network ID of 192.168.3.0 is different from the source Host As Network ID of 192.168.1.0 and therefore the packets will need to be routed to the destination Host B. 2. The source Host A must check its own Local Route Table for its default gateway (this is the general behavior unless a special route has been defined). The default gateway IP is the IP of the routing interface for that subnet. In this example it is 192.168.1.1 which is the IP of Router 1 Interface E1. Since this is an Ethernet LAN, Host A will need to encapsulate the frame in order to sent it out to the routing interface of E1 and to do so it needs to know the MAC address of the routing interface. If it is not in its local cache an ARP broadcast will need to be initiated in order to send the encapsulated frames to the routing interface (E1 on Router1).
3. In Figure26, the default gateways MAC address is not in Host As cache. Host A initiates a local ARP broadcast request attempting to resolve the IP address to a physical MAC address. 4. Router 1 responds with a unicast ARP response to Host A with its MAC address of 22. 5. Host A creates/encapsulates an Ethernet frame with its own MAC 11 as the source and a destination MAC address of 22. Notice the destination IP still remains 192.168.3.20 and the frame can be sent on the wire.
28
6. Once Interface E1 on R1 receives the Ethernet frame it looks at the destination MAC address of the frame to check it if matches his own in order to determine if he is the recipient of the frame. In this case R1 interface E1 is the default gateway of Host A and therefore the intended recipient. R1 checks the frames Type field and notices 0x800 which indicates that there is an IP packet in the data portion of the Ethernet frame. R1 then proceeds to decapsulate the Ethernet frame in order to analyze the destination IP of the packet. 7. The Router must then consult its routing table to determine what to do with the packet. In general terms it looks to identify network routes in its table which would include the destination IP address as a host address on that network. Note: If there are several viable routes to the destination network it will chose the route with the longest subnet mask match. How routing tables become populated and an in depth look of how they are evaluated are beyond the scope of this example and class. After viewing R1s routing table it finds that the network address of 192.168.3.0 is the destination network where these packets need to be routed. It also notices the next hop IP of 192.168.2.2 which represents the next stop for the packets on its way to the 192.168.3.0 network and this can be reached through local interface E2. 8. In order for R1 to do the frame encapsulation process it needs to know the MAC address of the 192.168.2.2 interface. So it must check its local ARP cache and again if the MAC address is not found, it must send an ARP broadcast to request the MAC address. In this case it will be already present. Therefore the frame encapsulation process can continue. Notice that the source and destination IP addresses stay the same but the source MAC becomes 33 and the destination MAC becomes 44. Also note that it also will decrement the Time to Live field of the packet (in the IP header) by 1. Now the packet is sent on the wire.
29
9. Once Interface E1 on R2 receives the Ethernet frame, it looks at the destination MAC address of the frame to check it if matches his own in order to determine if he is the recipient of the frame. In this case R2 interface E1 is the next hop IP of R1 and therefore the intended recipient. R2 checks the frames Type field and notices 0x800 which indicates that there is an IP packet in the data portion of the Ethernet Frame. R2 then proceeds to decapsulate the Ethernet frame in order to analyze the destination IP of the packet. 10. R2 must then consult its routing table to determine what to do with the packet. After consulting its routing table it finds that the Network Address of 192.168.3.0 is the destination network where these packets need to be forwarded and this is a directly connected route in its table through interface E2. 11. In order for R2 to do the frame encapsulation process it needs to know the MAC address of the final destination host B with the IP 192.168.3.20. So it must check its local ARP cache and again if the MAC address is not found it must be a ARP broadcast to resolve the IP Address to a matching physical MAC address. In this case it will be already present and therefore the frame encapsulation process can continue. Notice that the source MAC is 55 and the destination MAC becomes 66. Now the frame(s) are sent on the wire. 12. Once Host B receives the frame, it recognizes its own MAC address. It then decapsulates the frame and notices that itself is the intended host with an IP of 192.168.3.20.
30
Throughout the packet flow the source and destination IP addresses stay the same, but the source and destination MAC changes. Also, the Time to Live field of the packet (in the IP header) is decremented by 1.
31
The following command sequence sets up and activates VRRP-E. It follows the configuration rules which state the following:
The router interfaces in a VRID must be in the same IP subnet The Hello/Dead intervals must be set to the same values on all the VRRP-E enabled devices The Virtual IP (VIP) address must be configured the same on routers belonging to the same VRRP-E
backup group Router_A(config)# router VRRPExtended Router_A(config)# interface e1 Router_A(config-if-1)# ip address 192.53.5.2 Router_A(config-if-1)# ip VRRPExtended vrid 1 Router_A(config-if-1-vrid-1)# backup priority 110 track-priority 20 Router_A(config-if-1-vrid-1)# ip-address 192.53.5.1 <-- Virtual IP Router_A(config-if-1-vrid-1)# track-port e15 e16 Router_A(config-if-1-vrid-1)# activate Router_B(config)# router VRRPExtended Router_B(config)# interface e1 Router_B(config-if-1)# ip address 192.53.5.3 Router_B(config-if-1)# ip VRRPExtended vrid 1 Router_B(config-if-1-vrid-1)# backup priority 80 Router_B(config-if-1-vrid-1)# ip-address 192.53.5.1 Router_B(config-if-1-vrid-1)# activate
<-- Virtual IP
32
In Figure30, Router A and Router B use VRRP-E to load share as well as provide redundancy to the hosts. The load sharing is accomplished by creating two VRRP-E groups. Each group has its own virtual IP address. Half of the clients point to virtual IP address of VRID 1 as their default gateway and the other half point to virtual IP address of VRID 2 as their default gateway. This enables some of the outbound Internet traffic to go through Router A and the rest to go through Router B. VRRP-e reduces the priority of a VRRP-E interface by the amount of a tracked interface's priority if the tracked interface's link goes down. For example, if the VRRP-E interface's priority is 200 and a tracked interface with track priority 20 goes down, the software changes the VRRP-E interface's priority to 180. If another tracked interface goes down, the software reduces the VRIDs priority again, by the amount of the tracked interface's track priority.
33
Router A is the master for VRID 1 (backup priority = 110) and Router B is the backup for VRID 1 (backup priority = 100). RouterA and RouterB both track the uplinks to the Internet. If an uplink failure occurs on Router A, its backup priority is decremented by 20 (track priority = 20), so that all traffic destined to the Internet is sent through Router B instead. Similarly, RouterB is the master for VRID 2 (backup priority = 110) and RouterA is the backup for VRID 2 (backup priority = 100). Router A and Router B are both tracking the uplinks to the Internet. If an uplink failure occurs on RouterB, its backup priority is decremented by 20 (track priority = 20), so that all traffic destined to the internet is sent through RouterA instead.
34
4 - Routing Concepts
When you have completed reviewing this section be sure you can do the following:
Describe general routing concepts Demonstrate knowledge of the OSPF protocol Demonstrate basic knowledge of the BGP protocol Demonstrate basic knowledge of multicast routing
A distance-vector routing protocol Uses periodic updates to exchange routing information Uses hop count as its metric Limits the maximum number of hops allowed to 15 Hop count of 16 is considered an infinite distance and is used to remove inaccessible routes and limit routing loops
RIP is enabled on a per interface basis. This way RIP updates are not flooded out of every port. RIPv2 supports MD5 Does not scale well and can have poor convergence times
RIPv1 vs. RIPv2 Similarities:
Use of Split Horizon and/or Poison Reverse to prevent routing loops Maximum hop count of 15 Use of split horizon or split horizon with poison reverse Use of triggered updates
35
The following command sequence is an example of RIPv2 configuration. Router_A(config)# router rip Router_A(config-rip-router)# interface e1 Router_A(config-if-1)# ip address 207.95.8.1/24 Router_A(config-if-1)# ip rip v2-only Router_A(config-if-1)# interface ve 10 Router_A(config-if-2)# ip address 207.95.10.2 255.255.255.0 Router_A(config-if-2)# ip rip v2-only
Because of the Internet evolution there was a real concern that in the IPv4 address space, especially
Class B addresses would be exhausted
Running out of capacity in the global routing tables Eventual exhaustion of the entire 32-bit IP address space
The motivation behind CIDR implementations was allocating IP address space more efficiently. CIDR is used instead of handing out full classful addresses (A or B) to organizations that were not fully utilizing the entire address space. During the early adoption phase of CIDR a real concern existed about the imminent depletion of Class B networks. Class C networks were not favored by companies due to its inherent host address constraints. CIDR was seen as an interim solution until the adoption of IPv6 and its much larger address space. For example, if a network administrator needs 300 IP addresses she would typically need either a small portion of a class B networks, and thereby waste much of that address space, or 2 Class C networks (remember 254 hosts are possible in a standard Class C network). There is no middle ground with the structured classful address scheme. CIDR provides a mechanism for aggregating multiple smaller networks into a single larger network as in combining 2 Class C networks to provide 512 host addresses. CIDR provides the mechanism to combine multiple networks into groups or blocks, which the router treats as one big network (route summarization or route aggregation). For example, instead of having to store 10 Class C network addresses (any multiple number of smaller classful networks) the router can store a single CIDRbased network address. The eventual adoption of IPv6 is the answer to a much larger addressing space. Variable Length Subne Masks (VLSM) is used to set the boundary between host ID and network.
36
Subnetting
To begin we will use a fairly easy subnetting example for a traditional class C network 192.168.1.100 255.255.255.192
How many subnet bits are there? - 2 (most significant) bits from the 4th octet (27 or 128 + 26 or 64 = 192) How many Host ID bits are left? - 6 bits To determine the # of possible (sub) networks take the # of subnet bits to the power of 2 - In this case 22 = 4 possible (sub) networks - Remember there is only 1 possible network with the default subnet mask of 255.255.255.0 To determine the # of possible host addresses per subnetwork take the # of Host ID bits to the power of 2
and then subtract 2 for the network and broadcast addresses for the subnetwork
In this 26 - 2 = 64. 64 - 2 = 62 possible host addresses per subnetwork It is important to note when subnetting each subnetwork created has an identical number of host ID space created. In this example we can use up to 4 subnetworks and each subnetwork has a possible of 62 unique host addresses that can be deployed.
37
Administrative Distance
Each route in a routing table has a metric called an administrative distance in the range of 0-255. Lower metrics mean better values or routes are chosen. The lowest value administrative distance is the one that is stored in the routing table.
TABLE 2
Procotol Directly connected Static External BGP (eBGP) OSPF RIP Internal BGP (iBGP)
38
Decreases routing overhead Speeds up convergence Confines network instability to a single area of the network Communicates between routers using multicast advertisements
2011 Brocade Communications
Areas
Routers in OSPF are split into different groups called areas. The purpose is to reduce traffic and CPU load. The area that is the most restrictive uses the least resources (CPU and memory). Areas may be organized in any way that makes the most sense for a particular network. Areas are assigned numbers on the range of 1 through 4,294,967,295. Enabling OSPF logging is good for troubleshooting.
New York
San Jose
Los Angeles
Figure 32: OSPF Areas
Area Types:
Area 0 - Backbone - A required area to which all other areas must connect Ordinary or standard area (Normal or transit area) - All routers in a OSPF area have the same topological database, but their routing tables are based on
the routers position in the area and are unique to the router
Stub area - An area that does not accept external routes but accepts routes from within the same autonomous
system
Not So Stubby Area (NSSA) - A stub area does not accept external summary routes from the backbone, but can advertise external
summary routes into the backbone
39
Totally stubby area - This area wont accept routes from any other area. The Area Border Router (ABR) advertises 0.0.0.0/0
instead OSPF Autonomous System (AS) is the entire OSPF routing domain. An OSPF AS can be divided into multiple areas. The propagation of Types 1 and 2 Link State Advertisements is limited to the bounds of an area. An OSPF router can be a member of multiple areas. These routers are known as Area Border Routers (ABRs). Each ABR maintains a separate topological database for each area the router is in. Each topological database contains all of the LSAs within a given area. The routers within the same area have identical topological databases. The ABR is responsible for forwarding routing information or changes between its border areas. An Autonomous System Boundary Router (ASBR) is a router that is running multiple protocols and serves as a gateway to routers outside an AS. The ASBR is able to import and translate different protocols routes into OSPF through a process known as redistribution.
Level 1 - Intra-area routing Level 2 - Inter-area routing Level 3 - External Type 1 Metrics Level 4 - External Type 2 Metrics
If there are two routing paths to choose from then paths that are internal to an OSPF routing domain are preferred over external routes. External routes can be imported into the OSPF domain at two separate levels, one that has Type 1 Metrics and the other Type 2 Metrics.
40
The use of Type 1 metrics assumes that in the path from the OSPF router to the destination, the internal OSPF AS component (path to the ASBR advertising the AS-external-LSA) and external component are of the same importance. In Type 2 metrics, it is assumed that only the external component is more significant than the internal component. The aggregate cost to these external destinations does not change when viewed from different routers, since the internal costs are not important. But the cost of Intra-area and Inter-area destinations does change depending on which router the cost is observed.
Designated Routers
In order to minimize the amount of information exchange on a particular segment, OSPF elects one router to be a designated router and one router to be a backup designated router on each multi access segment. The idea behind this is that routers have a central point of contact for information exchange. Instead of each router exchanging updates with every other router on the segment, every router will exchange the information with the DR and BDR. The DR and BDR will relay the information to everybody else. The adjacency building process takes effect after multiple stages have been fulfilled. Routers that become adjacent will have the exact link state database.
Designated Router (DR) election is done by selecting the neighboring router with the highest priority. The router with the next largest priority is elected as the Backup DR (BDR). If the DR goes offline, the BDR automatically becomes the DR. The router with the next highest priority becomes the new BDR. If two neighbors share the same priority, the router with the highest router ID is designated as the DR. 1. The Router ID can be manually configured using the global ip router-id x.x.x.x command. 2. If the Router ID is not manually configured, the IP address configured on the lowest numbered loopback interface is used as the Router ID 3. If there is no loopback interface, then the router ID is the lowest numbered IP address configured on the device When only one router on the network claims the DR role despite neighboring routers with higher priorities or router IDs; this router remains the DR. This is also true for BDRs. The DR and BDR election process is performed when one of the following events occurs:
41
1. An interface is in a waiting state and the wait time expires 2. An interface is in a waiting state and a hello packet is received that addresses the BDR 3. A change in the neighbor state occurs, such as, a neighbor state transitions from 2 or higher, communication to a neighbor is lost, or a neighbor declares itself to be the DR or BDR for the first time
Type 1: Router LSA - generated by each router for each area to which it belongs. Type 2: Network LSA - generated by DRs describing the set of routers attached to a particular network. Type 3: Network Summary LSA - generated by ABRs describing inter-area routes. Type 4: ASBR Summary LSA - generated by ABRs advertising the IP address of the ASBR. Type 5: External LSA - generated by the ASBR describing networks external to the Autonomous System (AS). converts Type 7 LSAs into type 5 before flooding them into the backbone area (area 0).
Type 7: NSSA External LSA - generated by ASBR and only flooded within the Not-So-Stubby area. The ABR
Redistribution
Redistribution enables one routing protocol to learn and advertise routes that exist under some other process. The other process could be one or more of the following:
Another dynamic routing protocol (another instance of the same routing protocol or a different routing
protocol)
Static routes Directly connected interfaces on which no routing protocol has been enabled
The following command sequence uses the redistribution command to send OSPF routes as RIP updates. Redistribution enables one routing protocol to learn and advertise routes that exist under some other process. Router_B(config)# router rip Router_B(config-rip-router)# redistribution The following command sequence uses the redistribution rip command to send RIP routes as OSPF LSAs.
42
Router_B(config)# router ospf Router_B(config-ospf-router)# redistribution rip Router_B(config-ospf-router)# redistribution connected OSPF does not include directly connected networks in routing updates. The redistribution connected command takes directly connected routes and sends them out as OSPF LSAs. For the OSPF domain to have that network in its route tables, you must configure using the following command: Router_B(config-ospf-router)#redistribution connected The ip rip learn-default command allows a router to learn and advertise default RIP routes. This command is necessary on RIP routers, so they learn the default route redistributed from OSPF. This command can be applied on a global or interface basis. This example shows the feature enabled at the interface level: Router_D(config)#int e 2/2 Router_D(config-if-2/2)#ip rip learn-default Ideally, all routers within a given AS should run the same routing protocol. Rarely there are technical reasons to run multiple routing protocols. Redistributions should be avoided as much as possible.
43
1. Routers establish a TCP connection 2. Routers establish a BGP session 3. BGP peers exchange routing information
BGP routers do not automatically advertise any routes unless configured to do so (using the BGP network command) Router_A(config)#router bgp Router_A(config-bgp-router)#network 100.1.1.0/24
Initially the full BGP tables are exchanged; after that only incremental occur TCP connection stays alive until BGP problems cause termination
44
The BGP route table is empty until routes are injected into it from an IGP. This injection could be on a broad scale using the redistribution command, or very specific routes could be injected using the network command. The arrows in Figure38 display the prefix information that is received by Router A and Router C. When prefixes are advertised from a BGP peer, they are transmitted to all BGP neighbors. The arrows are being used to focus on routers A and C that use this prefix information. In a production network Router C, owned by an ISP, receives the entire Internet Routing table. Typically, a subset of these, for example a default route, is forwarded to Router A. Also in a production network, the Customer Prefix advertised by Router B would be one of the 100,000+ prefixes in the internet routing table. This information would allow all members of the internet access to AS 100. Router_B(config-bgp-router)# Router_D(config-bgp-router)#
CAUTION Liberal use of redistribution from and IGP into BGP can result in publishing private network information to destinations outside of the autonomous system, as well as illegal (unregistered) addresses.
45
Multicast Routing
PIM Sparse Mode
Brocade devices support Protocol Independent Multicast (PIM) Sparse version 2. PIM Sparse provides multicasting that is especially suitable for widely distributed multicast environments. The Brocade implementation is based on RFC 2362. In a PIM Sparse network, a PIM Sparse router that is connected to a host that wants to receive information for a multicast group must explicitly send a join request on behalf of the receiver (host). Traffic is optimized for a wide distribution. PIM Sparse routers are organized into domains. A PIM Sparse domain is a contiguous set of routers that all implement PIM and are configured to operate within a common boundary.
Switches that are configured with PIM Sparse interfaces also can be configured to fill one or more of the
following roles:
PMBR: A PIM switch that has some interfaces within the PIM domain and other interface outside the PIM domain. PMBRs connect the PIM domain to the Internet. BSR: The Bootstrap Router (BSR) distributes RP information to the other PIM Sparse switches within the domain. Each PIM Sparse domain has one active BSR. For redundancy, you can configure ports on multiple switches as candidate BSRs. The PIM Sparse protocol uses an election process to select one of the candidate BSRs as the BSR for the domain. The BSR with the highest BSR priority (a userconfigurable parameter) is elected. If the priorities result in a tie, then the candidate BSR interface with the highest IP address is elected. RP: The Rendezvous Point (RP) is the meeting point for PIM Sparse sources and receivers. A PIM Sparse domain can have multiple RPs, but each PIM Sparse multicast group address can have only one active RP. PIM Sparse switches learn the addresses of RPs and the groups for which they are responsible from messages that the BSR sends to each of the PIM Sparse switches.
To enhance overall network performance, Brocade Layer 3 Switches use the RP to forward only the first packet from a group source to the groups receivers. After the first packet, the Layer 3 Switch calculates the shortest path between the receiver and source (the Shortest Path Tree, or SPT) and uses the SPT for subsequent packets from the source to the receiver. The Layer 3 Switch calculates a separate SPT for each source-receiver pair. By default, when a multicast packet is received on a PIM-capable router interface in a multi-path topology, the interface checks its IP routing table to determine the shortest path back to the source. If the alternate paths have the same cost, the first entry in the IP routing table is picked as the path back to the source. When choosing the RPF, the router first checks the Multicast Routing Table. If the table is not available, it chooses an RPF from the IP Routing Table.
46
47
ACL Overview
Brocades FastIron devices support rule-based ACLs (sometimes called hardware-based ACLs), where the decisions to permit or deny packets are processed in hardware and all permitted packets are switched or routed in hardware. In addition, Brocades FastIron devices support inbound ACLs only; outbound ACLs are not supported. Rule-based ACLs program the ACL entries you assign to an interface into Content Addressable Memory (CAM) space allocated for the ports. The ACLs are programmed into hardware at startup (or as new ACLs are entered and bound to ports). Devices that use rule-based ACLs program the ACLs into the CAM entries and use these entries to permit or deny packets in the hardware, without sending the packets to the CPU for processing. Rule-based ACLs are supported on the following interface types:
Gigabit Ethernet ports 10 Gigabit Ethernet ports Trunk groups Virtual routing interfaces
Standard (ACL 1-99) - Permits or Denies packets based on source IP address - Configured with the access-list command Extended (ACL 100-199) - Permits or Denies packets based on source and destination IP addresses, TCP/UDP ports, or protocol
number/name
Configured with the access-list command The following are editing options for extended ACLs:
Insert a new ACL entry within an existing ACL Delete an entry from an ACL Replace an existing ACL entry Add, insert, replace, or delete a remark per ACL entry
48
If you can, try to apply ACLs Inbound rather than Outbound. Inbound ACL behavior states that the first instance of a TCP or UDP packet is handled by the ASIC and not the CPU. Enabling access list logging impacts the CPU. Example Standard ACL
Router_A(config)# ip dns server-address 209.157.22.30 Router_A(config)# access-list 1 deny host 209.157.22.26 log Router_A(config)# access-list 1 deny host 209.157.29.12 log Router_A(config)# access-list 1 deny host IPHost1 log Router_A(config)# access-list 1 permit any Router_A(config)# interface ethernet 1/1 Router_A(config-if-1/1)# ip access-group 1 in Example Explanation Q: Why do the 2nd , 3rd, and 4th access list 1 lines have no subnet mask? A: With the host argument, there is an implicit /32 bit mask.
The host argument is used in the syntax as a substitute for the subnet mask. DNS server configuration allows a host name to be specified and it is looked up on the servers listed in the command, you can list up to four servers. The DNS servers are searched in the order listed in the configuration. Syslog entries: The first time an ACL entry permits or denies a packet, the software immediately generates a Syslog entry and SNMP trap. The software also starts a five-minute timer. The timer keeps track of all packets explicitly denied by the ACL entries. After five minutes, the software generates a single Syslog entry for each ACL entry that has denied a packet. The message indicates the number of packets denied by the ACL entry during the previous five minutes.
49
ISP_WAN
V L VE1 A N
192.168.2.1
R
VE3: 192.168.2.4/24
Customer B AS 110
209.157.23.X
192.168.2.2
AS 200
192.168.2.3
Customer C AS 120
209.157.24.X
Customer D AS 130
209.157.25.X
dscp-cos-mapping This option is similar to the dscp-matching command (described below). This option maps the Differentiated Services Code Point (DSCP) value in incoming packets to a hardware table that provides mapping of each of the 063 DSCP values, and distributes them among eight traffic classes (internal priorities) and eight 802.1p priorities. By default, the Brocade device does the 802.1p to CoS mapping.
dscp-marking Marks the DSCP value in the outgoing packet with the value you specify. internal-priority-marking and 802.1p-priority-marking Supported with the DSCP marking option, these commands assign traffic that matches the ACL to a hardware forwarding queue (internal-priority-marking), and re-mark the packets that match the ACL with the 802.1p priority (802.1p-priority-marking).
dscp-matching Matches on the packets DSCP value. This option does not change the packets forwarding priority through the device or mark the packet.
50
Strict Priority (SP) SP ensures service for high priority traffic. The software assigns the maximum
weights to each queue which causes the queuing mechanism to serve as many packets in one queue as possible before moving to a lower queue. This method biases the queuing mechanism to favor the higher queues over the lower queues.
Hybrid WRR and SP Starting with software release 02.2.00, an additional configurable queueing
mechanism combines both the strict priority and weighted round robin mechanisms. The combined method enables the Brocade device to give strict priority to delay-sensitive traffic such as VoIP traffic, and weighted round robin priority over other traffic types.
802.1p
The 802.1p priority is also called the Class of Service (CoS), and uses a 3-bit field There is support for up to 8 priority levels (0-7) with 7 being the highest It is not preserved end-to-end Trust levels can be one of the following:
Marking
Marking is the process of changing the packets QoS information (the 802.1p and DSCP information in a packet) for the next hop. For example, for traffic coming from a device that does not support DiffServ, you can change the packets IP Precedence value into a DSCP value before forwarding the packet. You can mark a packets Layer 2 CoS value, its Layer 3 DSCP value, or both values. The Layer 2 CoS or DSCP value the device marks in the packet is the same value that results from mapping the packets QoS value into a Layer 2 CoS or DSCP value. Marking is optional and is disabled by default. Marking is performed using ACLs. When marking is not used, the device still performs the mappings listed in Classification for scheduling the packet, but leaves the packets QoS values unchanged when the device forwards the packet.
51
7 - Wireless Concepts
After reviewing this section you should be able to do the following:
Wireless Protocols
802.11b Channels
802.11 divides each of its bands into channels, similar to how the radio and TV broadcast bands are allocated, but with greater channel width and overlap. There are only 3 non-overlapping channels available in the 802.11b standard.These are Channels 1,6, and 11. For WiFi access points that are located near each other it is recommended that they each use one of the above non-overlapping channels to minimize the effects of interference. (The following graphic is used with permission from the Creative Commons website.)
a VLAN that supports multiple access points per ESSID multiple ESSIDs per physical access point a VLAN for each ESSID to separate network traffic and can also specify that a VLAN be shared between
multiple ESSIDs
an ESSID that supports just one person an ESSID for Remote Access Point (AP), such as in a branch office, and that AP can also support ESSIDs
for local traffic Typically, a wireless LAN supports one beacon on a single BSSID (Basic Service Set Identifier), which can advertise the primary ESSID. Clients can request to associate to that BSSID by requesting one of the ESSIDs. The Brocade IronPoint Mobility Series allows you to customize a beacon per ESSID to support different access point settings, such as base or supported transmit rates, different BSSIDs, different beacon intervals, and different Delivery Traffic Indication Message (DTIM) periods. This beacon customization allows service customization for each ESSID, as well as more flexibility in supporting different clients and services.
52
802.11i
Brocade IronPoint Mobility Series supports both WiFi Protected Access (WPA) and WPA2 protocols that have been presented by the Wi-Fi Alliance as interim security standards that improve upon the known vulnerabilities of Wired Equivalent Privacy (WEP) until the release of the 802.11i standard. In WPA2, the WPA Message Integrity Code (MIC) algorithm is replaced by a message authentication code, CCMP, that is considered fully secure and the RC4 cipher is replaced by the Advanced Encryption Standard (AES), as described in CCMP-AES. WPA includes the encryption protocol Temporal Key Integrity Protocol (TKIP) and leverages existing 802.1X authentication, including the dynamic key management facility. If 802.1X authentication is not available (in a SOHO, for example), WPA2-Personal or WPA-Personal can be implemented as alternatives and provide for manual key distribution between APs and clients.
802.1X Authentication
For enterprise wireless security to scale to hundreds or thousands of users, an authentication framework that supports centralized user authentication must be used in addition to the encryption type specified by 802.11, WEP, or by using WPA/WPA2 , which incorporates TKIP/CCMP-AES and 802.1X authentication. The use of IEEE 802.1X offers an effective framework for authenticating and controlling user traffic to a protected network, as well as dynamically varying encryption keys if WPA/WPA2 is configured. 802.1X ties a protocol called EAP (Extensible Authentication Protocol) to both the wired and wireless LAN media and supports multiple authentication methods, such as token cards, Kerberos, one-time passwords, certificates, and public key authentication. There are three basic pieces to 802.1X authentication: 1. Supplicanta software client running on the wireless station 2. Authenticatorthe access point and the controller 3. Authentication Serveran authentication database, usually a RADIUS server such as Cisco ACS, Microsoft IAS or Funk (Juniper) Odyssey. Extensible Authentication Protocol (EAP) is used to pass the authentication information between the supplicant (the wireless station) and the authentication server (RADIUS, MS IAS, or other). The actual authentication is defined and handled by the EAP type. The access point (and the controller in the configuration) acts as the authenticator. The authenticator is a client of the RADIUS server that allows the supplicant and the authentication server to communicate. The EAP type you choose, and whether you choose to implement authentication in your organization, depends on the level of security you require.
53
Describe the tools used to monitor a network Desribe the tools used to manage a network Demonstrate how to apply security on switches and routers Describe maintenance procedures for switches and routers
Network Monitoring
Restricting Remote Access to the Device to Specific VLAN IDs
You can restrict management access to a Foundry device to ports within a specific port-based VLAN. VLANbased access control applies to the following access methods:
By default, access is allowed for all the methods listed above on all ports. Once you configure security for a given access method based on the VLAN ID, access to the device using that method is restricted to only the ports within the specified VLAN.
Syslog Messages
A Brocade devices software can write syslog messages to provide information at the following severity levels:
The device writes the messages to a local buffer. The buffer can hold up to 1000 entries. You also can specify the IP address or host name of up to six Syslog servers. When you specify a Syslog server, the Brocade device writes the messages both to the system log and to the Syslog server. Using a Syslog server ensures that the messages remain available even after a system reload. The Brocade devices local Syslog buffer is cleared during a system reload or reboot, but the Syslog messages sent to the Syslog server remain on the server. By default, to view Syslog messages generated by a Brocade device, you need to display the Syslog buffer or the log on a Syslog server used by the Brocade device. You can enable real-time display of Syslog messages on the management console. When you enable this feature, the software displays a Syslog message on the management console when the message is generated. However, to enable display of real-time Syslog messages in Telnet or SSH sessions, you also must enable display within the individual sessions. To enable real-time display of Syslog messages, enter the logging console command at the global CONFIG level of the CLI. FastIron(config)#logging console
sFlow is supported on all Ethernet ports (10/100, Gigabit, and 10 Gigabit) Enabling sFlow may cause a slight and noticeable increase of up to 20% in CPU utilization. In typical
scenarios, this is normal behavior for sFlow, and it does not affect the functionality of other features on the switch.
The sampling rate is the average ratio of the number of packets incoming on an sFlow enabled port, to the
number of flow samples taken from those packets. sFlow sampling can affect performance in some configurations.
Note that on the FastIron devices, the configured sampling rate and the actual rate are the same. The
software does not adjust the configured sampling rate as on other Brocade devices.
55
The mirror port is the port to which the monitored traffic is copied. Attach your protocol analyzer to the
mirror port.
The monitored port is the port whose traffic you want to monitor
Network Management
Console Port
The first step in configuring your Brocade device is to connect a console cable (typically shipped with your device) to the serial port. You can then use the Command Line Interface (CLI ) to assign an IP address. After you assign an address, you can access the system through Telnet, the Web management interface, or Iron View. In order to attach a management station using the serial port, connect a PC or terminal to the serial port using a straight through cable. You will need a serial interface on your computer or a DB9-to-USB converter to be able to access the switch. The serial port has a male DB-9 connector. You will need a straight-through (female-to-female) cable. You need to run a terminal emulation program such as Hyperterm or Procomm plus on the PC. The session parameters should be set to the following:
Baud: 9600 Data Bits: 8 Parity: none Stop Bits: 1 Flow control: none
56
SNMP
SNMP is a set of protocols for managing complex networks. SNMP sends messages, called protocol data units (PDUs), to different parts of a network. SNMP-compliant devices, called agents, store data about themselves in Management Information Bases (MIBs) and return this data to the SNMP requesters. SNMP management access may be controlled, or restricted, by using a VLAN or ACLs.
Applying Security
Restricting Remote Access
By default, a Brocade device does not control remote management access based on the IP address of the managing device. You can restrict remote management access to a single IP address for the following access methods:
SNMP and Web Management use community strings for authentication. In addition, you can restrict all access methods to the same IP address using a single command. To restrict Telnet access: FastIron(config)# telnet-client 209.157.22.39 To restrict SSH access: FastIron(config)# ip ssh client 209.157.22.39 To restrict Web Management access: FastIron(config)# web-client 209.157.22.39 To restrict SNMP access: FastIron(config)# snmp-client 209.157.22.39 To restrict all access: FastIron(config)# all-client 209.157.22.39 To restrict access using ACLs the command is basically the same for all, except for the modifier before the access group. An example for Telnet: FastIron(config)# FastIron(config)# FastIron(config)# FastIron(config)# FastIron(config)# FastIron(config)# FastIron(config)# access-list 10 deny host 209.157.22.32 log access-list 10 deny 209.157.23.0 0.0.0.255 log access-list 10 deny 209.157.24.0 0.0.0.255 log access-list 10 deny 209.157.25.0/24 log access-list 10 permit any telnet access-group 10 write memory
57
To allow Telnet access to the device, you must first issue the telnet server command. If you wish to allow SSHv2 access, additionally, you must generate a Crypto Key. That is done with the crypto key generate command. In addition, you must use AAA authentication to create a password to allow SSHv2 access.
User: Displays information and perform basic tasks such as pings and traceroutes - View basic information - Verify connectivity (ping command) Privileged: Allows you use the same commands as those at the User level plus configuration commands
that do not require saving the changes to the system-config file
Enter through the enable command Can be password protected View detailed information (show commands) Execute system-wide features
CONFIG: Allows you make configuration changes to the device. To save the changes across reboots, you
need to save them to the system-config file. The CONFIG level contains sub-levels for individual ports, for VLANs, for routing protocols, and other configuration areas.
Enter through the configure terminal command Make global or local system changes (VLANs) Save changes with the write memory command
You can tell which level of the command hierarchy that you are currently at by looking at the system prompt.
58
Securing CLI
There are 5 ways to secure access to the Privileged EXEC and CONFIG levels of CLI:
Establish a password for Telnet access to the CLI Establish passwords for management privilege levels Set up local user accounts Configure TACACS/TACACS+ security Configure RADIUS security
Maintenance Procedures
Switch and Router show Commands
The following show commands are from routers and switches.
show stat: Interface statistics show ip: IP address and mask information show span: Spanning tree information show mac-address: MAC forwarding table
59
show mac-address stat: Number of MACs learned per port show flash: Flash memory images
FastIron# show flash Active Management Module (Slot 9): Compressed Pri Code size = 3613675, Version 03.1.00aT3e3 (sxr03100a.bin) Compressed Sec Code size = 2250218, Version 03.1.00aT3e1 (sxs03100a.bin) Compressed BootROM Code size = 524288, Version 03.0.01T3e5 Code Flash Free Space = 9699328 Standby Management Module (Slot 10): Compressed Pri Code size = 3613675, Version 03.1.00aT3e3 (sxr03100a.bin) Compressed Sec Code size = 2250218, Version 03.1.00aT3e1 (sxs03100a.bin) Compressed BootROM Code size = 524288, Version 03.0.01T3e5 Code Flash Free Space = 524288
show vlan: Configured VLANs show telnet: IP address(es) of active telnet session(s) show trunk: Configured and active trunk groups show tech-support: Details for assistance in troubleshooting when working with Support
File Management
The flash memory is divided into two different storage areas. This allows you to have two different software image versions stored in the flash memory. Secondary flash is storage space for upgrade code:
Put new code in the secondary flash Schedule a reload to boot on secondary flash during low traffic periods. Unsuccessful reloads will cause
the system to revert back to primary flash.
When confidence is established in upgrade code, use the copy flash flash primary command to
overwrite the old software image with the upgrade image in primary flash
The following command copies the system image in the primary flash to the TFTP server: - FastIron# copy flash tftp 192.22.33.44 vm1r07501.bin primary - A failure may indicate the presence of something in the secondary flash
60
9 - Troubleshooting
After reviewing this section you should be able to do the following:
Demonstrate knowledge of troubleshooting tools and techniques Demonstrate ability to analyze troubleshooting output
A route to the target is unavailable An ARP for the default gateway could not be resolved The default gateway does not exist
Collisions
An increasing collision rate (number of packets output divided by the number of collisions) does not indicate a problem: it is merely an indication of a higher offered load to the network. An example of this could be because another station was added to the network. Excessive collisions indicate a problem. Common causes are devices connected as full-duplex on a shared Ethernet, broken NICs, or simply too many stations on the shared medium. The excessive collisions can be resolved by hardcoding speed and duplex.
Gathering Data
As previously mentioned, the show tech command is extremely useful in gathering data for an escalated support call. The more information you can provide up front, the more likely a faster resolution is possible.
Root port - port having the best path to the root switch Designated port - on a given link, it is the port having the superior BPDU Edge port - a special type of designated port. It is a port that has been identified through a manual
configuration as being at the edge of the network and comes up immediately as a designated port.
2011 Brocade Communications
61
Blocking Ports
Alternate port - a port that is not a root port, and can not be a designated port, because it is receiving a
superior BPDU from another switch
Backup port - a port that is not a root port, and can not be a designated port, because it is receiving a
superior BPDU from its own switch
Disabled port - a port not controlled by RSTP either because it is down, administratively down, or
administratively removed from RSTP
Different route sources are shown above, both static and dynamically learned. If a route to a destination network is expected and is not shown, the router has not learned the route.
62
The following Non-Disclosure Confidentiality Agreement (the Agreement) sets forth the terms and conditions of your use of the exam materials as defined below. The Disclosure to you of this Exam and any questions, answers, worksheets, computations, drawings, diagrams, or any communications, including verbal communication by any party, regarding or related to the Exam and such Exam Materials and any derivatives thereof is subject to the Terms and Conditions of this Agreement. You understand, acknowledge and agree:
That the questions and answers of the Exam are the exclusive and confidential property of Brocade and are
protected by Brocade intellectual property rights;
That you may not disclose the Exam questions or answers or discuss any of the content of the Exam Materials
with any person, without prior approval from Brocade;
Not to copy or attempt to make copies (written, photocopied, or otherwise) of any Exam Material, including,
without limitation, any Exam questions or answers;
Not to sell, license, distribute, or give away the Exam Materials, questions, or answers; You have not purchased, solicited or used unauthorized (non-Brocade sanctioned) Exam Materials, questions,
or answers in preparation for this exam;
That your obligations under this Agreement shall continue in effect after the Exam and, if applicable, after
termination of your credential, regardless of the reason or reasons for terminations, and whether such termination is voluntary or involuntary.
Brocade reserves the right to take all appropriate actions to remedy or prevent disclosure or misuse, including, without limitation, obtaining an immediate injunction. Brocade reserves the right to validate all results and take any appropriate actions as needed. Brocade also reserves the right to use any technologies and methods for verifying the identity of candidates. Such technology may include, without limitation, personally identifiable information, challenge questions, identification numbers, photographic information, and other measures to protect against fraud and abuse. Neither this Agreement nor any right granted hereunder shall be assignable or otherwise transferable by you. By clicking on the "A" button (YES, I AGREE), you are consenting to be bound by the terms and conditions of this agreement and state that you have read this agreement carefully and you understand and accept the obligations which it imposes without reservation. You further state that no promises or representations have been made to induce agreement and that you accept this agreement voluntarily and freely. A. B. YES, I AGREE NO, I DO NOT AGREE
63
64