Professional Documents
Culture Documents
Total 23 pages
Website:
http://support.huawei.com
E-MAIL:
support@huawei.com
Address:
Bantian, Longgang District, Shenzhen, P. R.
Postal Code:
518129
China
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters.
Copyright Huawei Technologies Co., Ltd. 2004. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Internal use
Table of Contents
T01 IRAT Mobility Test ........................................................................................................................... 1 T01-01 L2U IRAT ............................................................................................................................ 1 T01-0101 LTE to UMTS cell reselection, LTE has higher cell priority ................................... 1 T01-0102 LTE to UMTS PS handover based on coverage with measurement......................... 4 T01-0103 LTE to UMTS redirection based on coverage with measurement............................ 8 T01-0104 LTE to UMTS redirection based on only serving cell measurement, UE don't support UTRAN measurement ................................................................................................ 11 T01-02 L2G IRAT .......................................................................................................................... 14 T01-0201 LTE to GERAN cell reselection for a PS attached UE in idle mode, LTE has higher cell priority ................................................................................................................... 14 T01-0202 LTE to GERAN redirection based on only serving cell measurement, UE don't support GERAN measurement ................................................................................................ 17
Issue: IRAT
Page i of i
Internal use
T01
Prerequisites
1. 2. 3. The LTE/EPC system is in normal operation. The LTE cell is activated, and its status is normal. The SGSN and GGSN are in normal operation.
Issue: IRAT-eRAN2.1
Page 1 of 20
Huawei Test Cases Description for MTN 4. 5. The UMTS cell is activated, and its status is normal.
Internal use
The status of the eNodeB is normal. The status can be checked by choosing Workbench > Main
Topology on the M2000. 6. 7. The following tasks have been created on the M2000: Uu interface tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > Uu
Interface Trace ) 8. S1 interface tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > S1
Interface Trace ) 9. Cell DT tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > Cell DT
Trace ) 10. 11. 12. 13. 14. 15. A TCP/UDP test tool such as Iperf has been installed on the server and client. The network is unloaded. The test UE is ready and located at the center of its serving cell. The UE is subscribed on the HSS as follows: QCI = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s A UE tracing tool, such as HUAWEI GENEX Probe for HUAWEI terminals or XCAL for Samsung
terminals or QXDM, is ready. 16. Add a neighboring UTRA frequency by running the following MML command: ADD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738, UtranFddTddType=UTRAN_FDD, UtranUlArfcnCfgInd=NOT_CFG, CellReselPriorityCfgInd=CFG, CellReselPriority=5;
Procedure
1. Set information related to cell reselection to
Expected Result
Operation succeeded.
UMTS by running the following MML command: ADD CELLRESELUTRAN: LocalCellId=0, SpeedStateSfCfgInd=NOT_CFG; 2. Configure the LTE cell reselection parameter
with higher cell priority than UMTS by running the following MML command: MOD CELLRESEL: LocalCellId=0, CellReselPriority=6; MOD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738, CellReselPriorityCfgInd=CFG, CellReselPriority=5; 3. Set the PS inactivity timer to 10s to increase the Operation succeeded.
probability of UE state transition to idle mode by running the following MML command: MOD RRCCONNSTATETIMER: UeInactiveTimer=10; Record the default value of the PS inactivity timer for post-test restoration. 4. Power on the UE so that it initiates the attach The messages INITIAL UE MSG and the last UL UE
Issue: IRAT-eRAN2.1
Page 2 of 20
Internal use MESSAGE (UL NAS TRANS) appear in the S1 tracing result, indicating that the attach procedure is successful. The UE camps on the LTE cell.
5.
The message RRC Connection Release indicates that the UE switches to idle mode. The NAS message Routing Area Update Request in the Initial UE message on the Iu interface indicates that the reselection procedure is successful.
6.
lab, decrease the power from the LTE cell and increase the power from the UMTS cell to trigger reselection to UMTS. 7. 8. 9. Ping 32bytes from UE to FTP server. Disconnect the UE and save the logs. Restore the test environment by running the RMV UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738; MOD RRCCONNSTATETIMER
Remarks
1. 2. 3. 4. Time required: 1 hour Related specifications: 3GPP TS 36.300, 36.331, 36.413, 24.301, 23.401 Message flow:
Issue: IRAT-eRAN2.1
Page 3 of 20
Internal use
Issue: IRAT-eRAN2.1
Page 4 of 20
Internal use
Prerequisites
1. 2. 3. 4. The LTE/EPC system is in normal operation. The UMTS system is in normal operation. The test UE is ready and located at the center of its serving cell. Uu and S1 interface tracing tasks have been created on the M2000 or eNodeB Web LMT, and Iu and Uu
interface tracing tasks have been created on the M2000 or RNC Web LMT. 5. CELL1 is configured in the eNodeB and CELL2 is configured in the RNC. CELL1 and CELL2 have the
same coverage. 6. 7. 8. The UE is subscribed on the HSS as follows: QCI = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s The UeInactiveTimer parameter is set as follows to keep the UE in connected mode: MOD RRCCONNSTATETIMER: UeInactiveTimer=0; 9. CELL2 is configured as an inter-RAT neighboring cell of CELL1 in the eNodeB by running the following
MML commands: ADD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738, UtranFddTddType=UTRAN_FDD, UtranUlArfcnCfgInd=NOT_CFG, CellReselPriorityCfgInd=CFG, CellReselPriority=6; ADD UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001, UtranDlArfcn=10738, UtranUlArfcnCfgInd=NOT_CFG, RncId=1, RacCfgInd=CFG, Rac=0, PScrambCode=150, Lac=1; ADD UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001, BlindHoPriority=32;
Procedure
1. Enable LTE to UMTS PS handover switchby
Expected Result
Operation succeeded.
running the following MML command: Issue: IRAT-eRAN2.1 Huawei Proprietary and Confidential Page 5 of 20
Huawei Test Cases Description for MTN MOD ENODEBALGOSWITCH: HoModeSwitch=UtranPsHoSwitch-1; Record the default values of the algorithm switches for post-test restoration. 2. Query the inter-RAT handover policy group ID of ---------START--------
Internal use
%%LST STANDARDQCI: Qci=QCI9;%% RETCODE = 0 ... QoS Class Indication = QCI 9 = 3 Operation succeeded.
InterRAT policy config group ID ... ---------END-------3. Based on the queried inter-RAT handover policy Operation succeeded.
group ID, enable PS handover to UTRAN in the group by running the following MML command: MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO-1; Record the default values of the algorithm switches for post-test restoration. 4. Power on the UE so that it initiates the attach The UE attaches to CELL1.
procedure. 5. Use FTP tool or Iperf to perform downlink data Data is transmitted properly. The UE reports event A2 to the eNodeB. After receiving the report, the eNodeB delivers the inter-RAT measurement configuration to the UE. The UE performs inter-RAT measurements. If the signal quality of the UMTS cell meets the threshold for reporting event B1, the UE reports event B1 to the eNodeB. Then, the eNodeB sends a handover command to the UE. The RRC_MOBIL_FROM_EURAN_CMD message in the LTE Uu interface tracing log and the Handover to UTRAN Complete in Uu interface and PS Handover Complete messages in the RNC Iu interface tracing log indicate that the UE is handed over to the UMTS cell. The data transmission in UMTS side is normal. 7. 8. Disconnect the UE and save the logs. Restore the test environment by running the Operation succeeded. Operation succeeded.
following MML commands: Issue: IRAT-eRAN2.1 Huawei Proprietary and Confidential Page 6 of 20
Huawei Test Cases Description for MTN RMV UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANEXTERNALCELLPLMN: UtranCellId=15001, Mcc="460", Mnc="150", ShareMcc="460", ShareMnc="20"; RMV UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738; MOD ENODEBALGOSWITCH MOD RRCCONNSTATETIMER
Internal use
Remarks
Message flow:
Issue: IRAT-eRAN2.1
Page 7 of 20
Internal use
UE
eNodeB
RNC
MME
SGSN
UE Attach Procedure
RRC_MEA_RPRT(A2)
RRC_CONN_RECFG(B1)
RAU Procedure
Issue: IRAT-eRAN2.1
Page 8 of 20
Internal use
Prerequisites
1. 2. 3. 4. 5. 6. The LTE/EPC system is in normal operation. The UMTS system is in normal operation. The test UE is ready and located at the center of its serving cell. The UE is subscribed on the HSS as follows: QCI = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s Uu and S1 interface tracing tasks have been created on the M2000 or eNodeB Web LMT, and Iu and Uu
interface tracing tasks have been created on the M2000 or RNC Web LMT. 7. 8. CELL1 is configured in the eNodeB and CELL2 is configured in the RNC. The UeInactiveTimer parameter is set as follows to keep the UE in connected mode: MOD RRCCONNSTATETIMER: UeInactiveTimer=0; 9. CELL2 is configured as an inter-RAT neighboring cell of CELL1 in the eNodeB by running the following
MML commands: ADD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738, UtranFddTddType=UTRAN_FDD, UtranUlArfcnCfgInd=NOT_CFG, CellReselPriorityCfgInd=CFG, CellReselPriority=6; ADD UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001, UtranDlArfcn=10738, UtranUlArfcnCfgInd=NOT_CFG, RncId=1, RacCfgInd=NOT_CFG, PScrambCode=150, Lac=1; ADD UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001, BlindHoPriority=16;
Procedure
1. On the M2000 or eNodeB Web LMT, query
Expected Result
Operation succeeded.
algorithm switch settings for post-test restoration by running the following MML commands: Issue: IRAT-eRAN2.1 Huawei Proprietary and Confidential Page 9 of 20
Huawei Test Cases Description for MTN LST ENODEBALGOSWITCH 2. Disable PS handover and redirection to UTRAN Operation succeeded.
Internal use
by running the following MML commands: MOD ENODEBALGOSWITCH: HoModeSwitch=UtranPsHoSwitch-0&UtranR edirectSwitch-1; 3. Power on the UE so that it initiates the attach The messages INITIAL UE MSG and the last UL UE MESSAGE (UL NAS TRANS) appear in the S1 tracing result, indicating that the attach procedure is successful. The UE attaches to CELL1. 4. Use FTP tool or Iperf to perform downlink data Data is transmitted properly. The UE reports event A2 to the eNodeB. After receiving the report, the eNodeB delivers the inter-RAT measurement configuration to the UE. The UE performs inter-RAT measurements. If the signal quality of the UMTS cell meets the threshold for reporting event B1, the UE reports event B1 to the eNodeB. Then, the eNodeB sends a redirection command to the UE. The redirected carrierInfo IE in the RRC_CONN_REL message on the Uu interface indicates that the redirection is triggered successfully. The Routing Area Update Request message in the Initial UE message on the Iu interface indicates that the redirection procedure is successful. The data transmission in UMTS side is normal. 6. 7. Disconnect the UE and save the logs. Restore the test environment by running the RMV UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738; MOD RRCCONNSTATETIMER: UeInactiveTimer=1800; Operation succeeded. Operation succeeded.
procedure.
Remarks
Message flow:
Issue: IRAT-eRAN2.1
Page 10 of 20
Internal use
UE
eNodeB
RNC
MME
SGSN
UE Attach Procedure
Adjust Attenuation (if in lab) RRC_MEA_RPRT(A2) RRC_CONN_RECFG(B1) RRC_MEA_RPRT(B1) RRC REL RRC Connection Req RRC Connection Setup RRC Connection Setup CMP
RAU Procedure
T01-0104 LTE to UMTS redirection based on only serving cell measurement, UE don't support UTRAN measurement
Objective If a UE does not support inter-RAT measurement, the eNodeB triggers LTE to UMTS redirection for the UE only after receiving a measurement report from the UE. This test case aims to verify that the eNodeB directly triggers LTE to UMTS redirection after receiving an event A2 report from a UE that does not support inter-RAT measurement. Network Diagram Lab test scenario:
Issue: IRAT-eRAN2.1
Page 11 of 20
Internal use
Prerequisites
1. 2. 3. 4. 5. The LTE/EPC system is in normal operation. The UMTS system is in normal operation. A TCP/UDP test tool such as Iperf has been installed on the server and client. The test UE is ready and located at the center of its serving cell. Uu and S1 interface tracing tasks have been created on the M2000 or eNodeB Web LMT, and Uu and Iu
interface tracing tasks have been created on the RNC Web LMT. 6. 7. 8. 9. The UE is subscribed on the HSS as follows: QCI = 9, AMBRMAXUL = 50000000, AMBRMAXDL = 100000000 CELL1 is configured in the eNodeB and CELL2 is configured in RNC1. CELL2 is configured as a neighboring cell with blind priority of CELL1 in the eNodeB by running the ADD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738, UtranFddTddType=UTRAN_FDD, UtranUlArfcnCfgInd=NOT_CFG, CellReselPriorityCfgInd=CFG, CellReselPriority=6; ADD UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001, UtranDlArfcn=10738, UtranUlArfcnCfgInd=NOT_CFG, RncId=1, RacCfgInd=NOT_CFG, PScrambCode=150, Lac=1; ADD UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001, BlindHoPriority=16;
Procedure
1. On the M2000 or eNodeB Web LMT, query
Expected Result
Operation succeeded.
algorithm switch settings for post-test restoration by running the following MML commands: LST ENODEBALGOSWITCH Issue: IRAT-eRAN2.1 Huawei Proprietary and Confidential Page 12 of 20
Huawei Test Cases Description for MTN 2. Disable PS handover and enable LTE to UMTS Operation succeeded.
Internal use
redirection by running the following MML commands: MOD ENODEBALGOSWITCH: HoModeSwitch=UtranPsHoSwitch-0&UtranR edirectSwitch-1; 3. Power on the UE so that it initiates the attach The messages INITIAL UE MSG and the last UL UE MESSAGE (UL NAS TRANS) in S1 interface indicate the success of the attach procedure. The UE attaches to CELL1. 4. Use FTP tool or Iperf to perform downlink data Data is transmitted properly. The RRC_MEA_RPRT message with A2 event report ID sent from the UE to the eNodeB on the Uu interface indicates that the change of coverage has triggered measurement of the serving cell. The redirected carrierInfo IE in the RRC_CONN_REL message on the Uu interface indicates that the redirection is triggered successfully. The Routing Area Update Request message in the Initial UE message on the Iu interface indicates that the redirection procedure is successful. The data transmission in UMTS side is normal. 6. 7. Disconnect the UE and save the logs. Restore the test environment by running the Operation succeeded. Operation succeeded.
procedure.
lab, adjust the attenuators to decrease the signal quality of CELL1 and increase that of CELL2 to trigger LTE to UMTS redirection.
following MML commands: RMV UTRANNCELL: LocalCellId=0, Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANEXTERNALCELL: Mcc="460", Mnc="150", UtranCellId=15001; RMV UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738;
Remarks
1. 2. Time required: 0.5 hours Message flow:
Issue: IRAT-eRAN2.1
Page 13 of 20
Internal use
UE
eNodeB
RNC
MME
SGSN
UE Attach Procedure
Adjust Attenuation (if in lab) RRC_MEA_RPRT(A2) RRC REL RRC Connection Req RRC Connection Setup RRC Connection Setup CMP
RAU Procedure
3.
Issue: IRAT-eRAN2.1
Page 14 of 20
Internal use
Prerequisites
1. 2. 3. 4. 5. The LTE/EPC system is in normal operation. The LTE cell is activated, and its status is normal. The SGSN and GGSN are in normal operation. The GERAN cell is activated, and its status is normal. The status of the eNodeB is normal. The status can be checked by choosing Workbench > Main
Topology on the M2000. 6. 7. The following tasks have been created on the M2000: Uu interface tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > Uu
Interface Trace ) 8. S1 interface tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > S1
Interface Trace ) 9. Cell DT tracing (by choosing Monitor > Signaling Trace > Signaling Trace Management > Cell DT
Trace ) 10. 11. 12. 13. 14. 15. A TCP/UDP test tool such as Iperf has been installed on the server and client. The network is unloaded. The test UE is ready and located at the center of its serving cell. The UE is subscribed on the HSS as follows: QCI = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s A UE tracing tool, such as HUAWEI GENEX Probe for HUAWEI terminals or XCAL for Samsung
terminals or QXDM, is ready. 16. The GERAN cell is configured as a neighboring cell of the LTE cell in the eNodeB by running the
Issue: IRAT-eRAN2.1
Page 15 of 20
Huawei Test Cases Description for MTN ADD GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0, GeranVersion=EDGE, StartingArfcn=800, BandIndicator=GSM_dcs1800, CellReselPriorityCfgInd=CFG, CellReselPriority=6, PmaxGeranCfgInd=NOT_CFG;
Internal use
Procedure
1. Set information about cell reselection to GERAN
Expected Result
Operation succeeded.
for the LTE cell by running the following MML command: ADD CELLRESELGERAN: LocalCellId=0, SpeedStateSfCfgInd=NOT_CFG; 2. Configure the LTE cell reselection parameter
with higher cell priority than UMTS by running the following MML command: MOD CELLRESEL: LocalCellId=0, CellReselPriority=6; MOD GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0, CellReselPriorityCfgInd=CFG, CellReselPriority=5; 3. Set the PS inactivity timer to 10s to increase the Operation succeeded.
probability of UE state transition to idle mode by running the following MML command: MOD RRCCONNSTATETIMER: UeInactiveTimer=10; Record the default value of the PS inactivity timer for post-test restoration. 4. Power on the UE so that it initiates the attach The messages INITIAL UE MSG and the last UL UE MESSAGE (UL NAS TRANS) on the S1 interface indicate that the attach procedure is successful. The UE camps on the LTE cell. 5. UE moves from LTE cell to GERAN cell. If in the The Routing Area Update Request message in the Initial UE message on the Iu interface indicates that the reselection procedure is successful.
procedure.
lab, decrease the power from the LTE cell and increase the power from the GERAN cell to trigger reselection to the GERAN cell. 6. 7. 8. Ping 32bytes from UE to FTP server. Disconnect the UE and save the logs. Restore the test environment by running the RMV CELLRESELGERAN: LocalCellId=0; MOD RRCCONNSTATETIMER
Remarks
1. Time required: 1 hour Huawei Proprietary and Confidential Page 16 of 20
Issue: IRAT-eRAN2.1
Huawei Test Cases Description for MTN 2. 3. 4. Related specifications: 3GPP TS 36.300, 36.331, 36.413, 24.301, 23.401 Message flow:
Internal use
T01-0202 LTE to GERAN redirection based on only serving cell measurement, UE don't support GERAN measurement
Objective This test case aims to verify that the eNodeB supports inter-RAT redirection to GERAN for UEs in connected mode based on coverage. Network Diagram Lab test scenario:
Issue: IRAT-eRAN2.1
Page 17 of 20
Internal use
Prerequisites
1. 2. 3. 4. The LTE/EPC system is in normal operation. The GERAN system is in normal operation. The test UE is ready and located at the center of its serving cell. Uu and S1 interface tracing tasks have been created on the M2000 or eNodeB Web LMT, and A and Gb
interface tracing tasks have been created on the BSC Web LMT. 5. 6. 7. 8. The UE is subscribed on the HSS as follows: QCI = 9, AMBRMAXUL = 50000000, AMBRMAXDL = 100000000 CELL1 is configured in the eNodeB and CELL2 is configured in the BSC. The UeInactiveTimer parameter is set as follows to keep the UE in connected mode: MOD RRCCONNSTATETIMER: UeInactiveTimer=0; 9. CELL2 is configured as an inter-RAT neighboring cell with blind handover priority of CELL1 in the
eNodeB by running the following MML commands: ADD GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0, GeranVersion=EDGE, StartingArfcn=800, BandIndicator=GSM_dcs1800, CellReselPriorityCfgInd= NOT_CFG, PmaxGeranCfgInd=NOT_CFG; ADD GERANEXTERNALCELL: Mcc="460", Mnc="150", GeranCellId=121, Lac=57345, RacCfgInd=NOT_CFG, BandIndicator=GSM_dcs1800, GeranArfcn=800, NetworkColourCode=0, BaseStationColourCode=0; ADD GERANNCELL: LocalCellId=0, Mcc="460", Mnc="150", Lac=57345, GeranCellId=121, BlindHoPriority=30; 10. UE don't support GERAN measurement.
Procedure
Issue: IRAT-eRAN2.1
Expected Result
Huawei Proprietary and Confidential Page 18 of 20
Huawei Test Cases Description for MTN 1. Enable LTE to GERAN redirection and disable Operation succeeded.
Internal use
LTE to GERAN PS handover for the eNodeB by running the following MML commands: MOD ENODEBALGOSWITCH: HoModeSwitch=GeranPsHoSwitch-0&Geran RedirectSwitch-1; 2. Power on the UE so that it initiates the attach The messages INITIAL UE MSG and the last UL UE MESSAGE (UL NAS TRANS) appear in the S1 tracing result, indicating that the attach procedure is successful. The UE camps on CELL1. 3. Use FTP tool or Iperf to perform downlink data Data is transmitted properly. If the signal quality of the LTE cell deteriorates and meets the threshold for reporting event A2, the UE reports event A2 to the eNodeB. After receiving the report, eNodeB sends an RRC CONNECTION RELEASE message to the UE. The RRC CONNECTION RELEASE message with "redirected CarrierInfo" on the Uu interface indicates the UE redirection from the LTE cell to the GERAN cell. The Routing Area Update Request message appears in the Gb tracing log, indicating that the redirection procedure is successful. The data transmission in GERAN side is normal. 5. 6. Disconnect the UE and save the logs. Restore the test environment by running the Operation succeeded. Operation succeeded.
procedure.
lab, decrease the LTE signal quality and raise the GERAN signal quality to trigger a redirection from LTE to GERAN.
following MML commands: RMV GERANNCELL: LocalCellId=0, Mcc="460", Mnc="150", Lac=57345, GeranCellId=121; RMV GERANEXTERNALCELL: Mcc="460", Mnc="150", GeranCellId=121, Lac=57345; RMV GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0; MOD RRCCONNSTATETIMER: UeInactiveTimer=1800;
Remarks
1. 2. 3. Time required: 1 hour Related specifications: 3GPP TS 36.300, 36.331, 36.413, 24.301, 23.401 Message flow: Huawei Proprietary and Confidential Page 19 of 20
Issue: IRAT-eRAN2.1
Internal use
UE
eNodeB
BSC
MME
SGSN
UE Attach Procedure
Adjust Attenuation (if in lab) RRC_MEA_RPRT(A2) RRC_CONN_REL Channel request Immediate Assignment
RAU Procedure
4.
Issue: IRAT-eRAN2.1
Page 20 of 20