Professional Documents
Culture Documents
Meshing
Meshing
Overview
Recall that meshing is a three-step procedure:
Define element attributes
Training Manual
In this chapter, we will expand on each of these steps and also discuss additional meshing options.
Topics covered:
A. Multiple Element Attributes B. Controlling Mesh Density C. Changing a Mesh D. Mapped Meshing E. Hex-to-Tet Meshing F. Mesh Extrusion G. Sweep Meshing H. Workshop
Meshing
Training Manual
As we discussed earlier, every element has the following attributes associated with it:
Element type (TYPE) Real constants (REAL) Material properties (MAT)
Most FEA models have multiple attributes. For example, the silo shown here has two element types, three real constant sets, and two materials.
TYPE 1 = shell TYPE 2 = beam
Meshing
Training Manual
Whenever you have multiple TYPEs, REALs and MATs, you need to make sure that each element is assigned the proper attributes. There are three ways to do this:
Assign attributes to the solid model entities before meshing Activate a global setting of MAT, TYPE, and REAL before meshing Modify element attributes after meshing
If no assignments are made, ANSYS uses default settings of MAT=1, TYPE=1, and REAL=1 for all elements in the model. Note, the current active TYPE, REAL, and MAT dictates mesh operation.
Meshing
Training Manual
Or select the desired entities and use the VATT, AATT, LATT, or KATT command. 3. When you mesh an entity, its attributes are automatically transferred to the elements.
Meshing
Training Manual
Activate the desired combination of attributes in the Meshing Attributes dialog box. We refer to these as the active TYPE, REAL, and MAT settings.
Or use the TYPE, REAL, and MAT commands. 3. Mesh only those entities to which the above settings apply.
Meshing
Training Manual
1. Define all necessary element types, materials, and real constant sets. 2. Activate the desired combination of TYPE, REAL, and MAT settings:
Preprocessor > -Attributes- Define > Default Attribs... Or use the TYPE, REAL, and MAT commands
3. Modify the attributes of only those elements to which the above settings apply:
Issue EMODIF,PICK or choose Preprocessor > Move/Modify > -ElementsModify Attrib Then pick the desired elements
Meshing
Training Manual
Element attributes assigned directly to solid model entities will override the default attribute pointers. By assigning attributes to solid model entities, you can avoid having to reset attributes in the middle of meshing operations. This is advantageous because ANSYS meshing algorithms are most efficient when meshing all entities at once. Clearing a solid model entity of its mesh will not delete attribute assignments.
Meshing
Training Manual
List element types, real constants, and materials. One of each has been defined.
Bring up MeshTool, choose area attributes, and press Set Pick the single area, show the Area Attributes dialog box, and press OK. (There is only one set of attributes, but this illustrates the general procedure.)
Meshing
Training Manual
ANSYS provides many tools to control mesh density, both on a global and local level:
Global controls SmartSizing Global element sizing Default sizing Local controls Keypoint sizing Line sizing Area sizing
Meshing
Training Manual
Determines element sizes by assigning divisions on all lines, taking into account curvature of the line, its proximity to holes and other features, and element order. SmartSizing is off by default, but is recommended for free meshing. It does not affect mapped meshing. (Free meshing vs. mapped meshing will be discussed later.)
Meshing
Training Manual
Meshing
Training Manual
Advanced SmartSize controls, such as mesh expansion and transition factors, are available on the SMRT command (or Preprocessor > -Meshing- Size Cntrls > -SmartSize- Adv Opts...)
You can turn off SmartSizing using the MeshTool or by issuing smrt,off.
Meshing
Training Manual
Meshing
Training Manual
If you dont specify any controls, ANSYS uses default sizing, which assigns minimum and maximum line divisions, aspect ratio, etc. based on element order. Meant for mapped meshing, but is also used for free meshing if SmartSizing is off.
You can adjust default size specifications using DESIZE or Preprocessor > -Meshing- Size Cntrls > -Global- Other.
Meshing
Training Manual
Different keypoints can have different KESIZEs, giving you more control over the mesh. Useful for stress concentration regions. Specified sizes may be overridden by SmartSizing to accommodate line curvature or proximity to features.
Meshing
Training Manual
Different lines can have different LESIZEs. Size specifications may be hard or soft.
Hard sizes are always honored by the mesher, even if SmartSizing is on. They take precedence over all other size controls. Soft sizes may be overridden by SmartSizing.
You can also specify a spacing ratio ratio of last division to first. Used to bias the divisions towards one end or towards the middle.
Meshing
Training Manual
Different areas can have different AESIZEs. Bounding lines will use the specified size only if they have no LESIZE or KESIZE specified and if no adjacent area has a smaller size. Specified sizes may be overridden by SmartSizing to accommodate line curvature or proximity to features.
Meshing
Training Manual
Meshing
C. Changing a Mesh
If a mesh is not acceptable, you can always re-mesh the model by following these steps:
1. Clear the mesh. The clear operation is the opposite of mesh: it removes nodes and elements. Use the [Clear] button on the MeshTool, or use VCLEAR, ACLEAR, etc.
Training Manual
(If you are using the MeshTool, you may skip this step since the program will prompt you whether to clear or not when you execute step 3.)
2. Specify new or different mesh controls. 3. Mesh again.
Meshing
...Changing a Mesh
Another meshing option is to refine the mesh in specific regions.
Available for all area elements and only tetrahedral volume elements. Easiest way is to use the MeshTool: First save the database. Then choose how you want to specify the region of refinement at nodes, elements, keypoints, lines, or areas and press the Refine button. Pick the entities at which you want the mesh to be refined. (Not required if you choose All Elems.) Finally, choose the level of refinement. Level 1 (minimal refinement) is a good starting point.
Training Manual
Meshing
...Changing a Mesh
Demo:
Training Manual
Continuing the last demo (ribgeom has been meshed with ESIZE = 0.2) Choose refinement at Lines and press Refine Pick the top line, then choose the default minimal refinement
Meshing
D. Mapped Meshing
There are two main meshing methods: free and mapped. Free Mesh
Has no element shape restrictions. The mesh does not follow any pattern. Suitable for complex shaped areas and volumes.
Training Manual
Mapped Mesh
Restricts element shapes to quadrilaterals for areas and hexahedra (bricks) for volumes. Typically has a regular pattern with obvious rows of elements. Suitable only for regular areas and volumes such as rectangles and bricks.
Meshing
...Mapped Meshing
Free Mesh + Easy to create; no need to divide complex shapes into regular shapes. Volume meshes can contain only tetrahedra, resulting in a large number of elements. Mapped Mesh
Training Manual
+ Generally contains a lower number of elements. + Lower-order elements may be acceptable, so the number of DOF is lower. Areas and volumes must be regular in shape, and mesh divisions must meet certain criteria. Very difficult to achieve, especially for complex shaped volumes.
Only higher-order (10-node) tetrahedral elements are acceptable, so the number of DOF can be very high.
Meshing
...Mapped Meshing
Creating a Free Mesh Free meshing is the default setting for both area and volume meshes. Create a free mesh is easy:
Bring up the MeshTool and verify that free meshing is set. SmartSizing is generally recommended for free meshing, so activate it and specify a size level. Save the database. Then initiate the mesh by pressing the Mesh button. Press [Pick All] in the picker to choose all entities (recommended). Or use the commands VMESH,ALL or AMESH,ALL.
Training Manual
Meshing
...Mapped Meshing
Creating a Mapped Mesh
Training Manual
This is not as easy as free meshing because the areas and volumes have to meet certain requirements:
Area must contain either 3 or 4 lines (triangle or quadrilateral). Volume must contain either 4, 5, or 6 areas (tetrahedron, triangular prism, or hexahedron).
Meshing
...Mapped Meshing
Training Manual
For quadrilateral areas or hexahedral volumes, unequal divisions are allowed, as shown in these examples, but the number of divisions must satisfy a formula (shown on the next page).
Meshing
...Mapped Meshing
Training Manual
Meshing
...Mapped Meshing
Thus mapped meshing involves a three-step procedure:
Training Manual
Ensure regular shapes, i.e, areas with 3 or 4 sides, or volumes with 4, 5, or 6 sides. Specify size and shape controls Generate the mesh
Meshing
...Mapped Meshing
Ensure regular shapes
Training Manual
In most cases, the model geometry is such that the areas have more than 4 sides, and volumes have more that 6 sides. To convert these to regular shapes, you may need to do one or both of these operations:
Slice the areas (or volumes) into smaller, simpler shapes. Concatenate two or more lines (or areas) to reduce the total number of sides.
Meshing
...Mapped Meshing
Slicing can be accomplished with the Boolean divide operation.
Training Manual
Remember that you can use the working plane, an area, or a line as the slicing tool. Sometimes, it may be easier to create a new line or a new area than to move and orient the working plane in the correct direction.
Meshing
...Mapped Meshing
Training Manual
Concatenation creates a new line (for meshing purposes) that is a combination of two or more lines, thereby reducing the number of lines making up the area.
Use the LCCAT command or Preprocessor > -MeshingConcatenate > Lines, then pick the lines to be concatenated. For area concatenation, use ACCAT command or Preprocessor > -Meshing- Concatenate > Areas
Meshing
...Mapped Meshing
Training Manual
You can also imply a concatenation by simply identifying the three or four corners of the area. In this case, ANSYS internally generates the concatenation.
To do this, choose Quad shape and Map mesh in the MeshTool. Then change 3/4 sided to Pick corners. Press the Mesh button, pick the area, and then pick the 3 or 4 corners that form the regular shape.
Meshing
...Mapped Meshing
Notes on concatenation:
Training Manual
It is purely a meshing operation and therefore should be the last step before meshing, after all solid modeling operations. This is because the output entity obtained from a concatenation cannot be used in any subsequent solid modeling operation. You can "undo" a concatenation by deleting the line or area it produced. Concatenating areas (for mapped volume meshing) is generally much more complicated because you may also need to concatenate some lines. Lines are automatically concatenated only when two adjacent, 4sided areas are concatenated. Consider the add (Boolean) operation if the lines or areas meet at a tangent.
Meshing
...Mapped Meshing
Specify size and shape controls This is the second step of the three-step mapped meshing procedure. Choosing the shape is simple. In the MeshTool, choose Quad for area meshing, and Hex for volume meshing, then click on Map. Commonly used size controls and the order in which they are applied:
Line sizing [LESIZE] is always honored. Global element size , if specified, will be applied to unsized lines.
Training Manual
Default element sizing [DESIZE] will be applied to unsized lines only if ESIZE is not specified.
(SmartSizing is not valid.)
Meshing
...Mapped Meshing
If you specify line divisions, remember that:
Training Manual
divisions on opposite sides must match, but you only need to specify one side. The map mesher automatically transfers divisions to the opposite side. if you have concatenated lines, divisions can only be applied to the original (input) lines, not the composite line.
6 divisions specified on each original line. 12 divisions will be automatically applied to this line (opposite to composite line).
How many divisions are used for the other two lines? (Upcoming demo will answer it.)
Meshing
...Mapped Meshing
Generate the mapped mesh
Training Manual
Once you have ensured regular shapes and assigned the appropriate divisions, generating the mesh is easy. Just press the Mesh button in the MeshTool, then press [Pick All] in the picker or choose the desired entities.
Meshing
...Mapped Meshing
Question: How would you slice this model for mapped meshing?
Training Manual
Meshing
...Mapped Meshing
Demo:
Resume ribfull.db
Training Manual
Meshing
E. Hex-to-Tet Meshing
For volume meshing, we have only seen two options so far:
Free meshing, which creates an all-tet mesh. This is easy to achieve but may not be desirable in some cases because of the large number of elements and total DOF created. Mapped meshing, which creates an all-hex mesh. This is desirable but usually very difficult to achieve.
Training Manual
Hex-to-tet meshing provides a third option that is the best of both worlds. It allows you to have a combination of hex and tet meshes without compromising the integrity of the mesh.
Meshing
...Hex-to-Tet Meshing
Training Manual
This option works by creating pyramid-shaped elements in the transition region between hex and tet regions.
Requires the hex mesh to be available (or at least a quad mesh at the shared area). The mesher first creates all tets, then combines and rearranges the tet elements in the transition region to form pyramids. Available only for element types that support both pyramid and tet shapes, e.g:
Meshing
...Hex-to-Tet Meshing
Training Manual
Hex-to-tet meshing is valid for both quadratic-to-quadratic and linear-toquadratic transitions. Element type must support a 9-node pyramid for the latter. Hex Mesh Transition Layer Tet Mesh
Quadratic to Quadratic
20-Node Hex 13-Node Pyramid 10-Node Tet
Meshing
...Hex-to-Tet Meshing
Procedure involves four steps: 1. Create the hex mesh.
Training Manual
Start by map-meshing the regular-shaped volumes. (Or mesh the shared areas with quads.)
For stress analysis, use either an 8-node brick (SOLID45 or SOLID185) or a 20-node brick (SOLID95 or SOLID186).
Meshing
...Hex-to-Tet Meshing
Training Manual
Thermal SOLID90
Multiphysics SOLID62, 117, 122
Meshing
...Hex-to-Tet Meshing
3. Generate the tet mesh.
First activate free meshing.
Training Manual
Meshing
...Hex-to-Tet Meshing
4. Convert degenerate tets to true 10-node tets.
Training Manual
The tet mesh created by the transition mesher consists of degenerate elements 10-node tetrahedra derived from 20node bricks, for example. These elements are not as efficient as true 10-node tets such as SOLID92, which use less memory and write smaller files during solution.
Meshing
...Hex-to-Tet Meshing
Demo:
Resume hextet.db
Training Manual
Show element type list using Element Type > Add/Edit/Delete. There are two element types: SOLID45 & 95
Bring up MeshTool and set ESIZE,1 (size) Map-mesh the regular shaped volume Set element type to 2, and activate tet-meshing Free-mesh the other volume Convert degenerate tets to SOLID92 Show element type list. There are now three element types.
Meshing
F. Mesh Extrusion
Training Manual
When you extrude an area into a volume, you can extrude the area elements along with it, resulting in a meshed volume. This is called mesh extrusion. Advantage: Easy to create a volume mesh with all bricks (hexahedra) or a combination of bricks and prisms. Obvious requirement: Shape of the volume must lend itself to extrusion.
Extrude
Meshing
...Mesh Extrusion
Procedure 1. Define two element types an area element and a volume element.
Area element: Choose MESH200 quadrilaterals. MESH200 is a meshonly (Not Solved) element and has no DOFs or material properties associated with it. Volume element: Should be compatible with the MESH200 element type. For example, if you choose midside nodes for MESH200, the 3-D solid element should also have midside nodes. ET command or Preprocessor > Element Type > Add/Edit/Delete
Training Manual
Meshing
...Mesh Extrusion
2. Mesh the area to be extruded with MESH200 elements.
Use mapped or free meshing with desired mesh density. Preprocessor > MeshTool
Training Manual
Meshing
...Mesh Extrusion
4. Extrude the area.
Training Manual
First delete concatenated lines, if any. If concatenations are present, ANSYS will not allow the extrusion operation. Preprocessor > -Meshing- Concatenate > -Del Concats- Lines Then extrude the area using any of the extrusion methods.
Meshing
...Mesh Extrusion
Demo:
Resume ribgeom.db
Training Manual
Bring up the Element Types dialog, delete PLANE82 element type, and replace it with MESH200 4-node quad
Also add SOLID45 as element type 2 Bring up MeshTool and set ESIZE,0.1 Choose free quad-meshing and mesh the area Set extrusion options: TYPE=2, number of element divisions = 4 Rotate view to ISO Extrude area along normal with offset = 0.4
Meshing
G. Sweep Meshing
Training Manual
Sweep meshing is yet another option available for volume meshing. It is the process of meshing an existing volume by sweeping an area mesh. Similar to mesh extrusion, except that the volume already exists in this case (from a geometry import, for example).
Meshing
...Sweep Meshing
Advantages:
Easy to create a volume mesh with all bricks (hexahedra) or a combination of bricks and prisms. Option to tet-mesh volumes that are not sweepable. Transition pyramids are automatically generated.
Source surface (1 area)
Training Manual
Requirements:
Topology of the volume must be consistent in the sweep direction. Example: a block with a through hole (ok even if the hole is tapered). Source and target surfaces must be single areas. Concatenated areas are not allowed for either the source or the target.
Meshing
...Sweep Meshing
Procedure Define and activate a 3-D hexahedral solid element type, such as structural SOLID45 or SOLID95. Bring up MeshTool and choose Hex/Wedge and Sweep. Choose how the source and target surfaces are identified:
Auto Source/Target means that ANSYS will automatically choose them based on the volumes topology. Pick Source/Target means that you will be choosing them.
Training Manual
Press the SWEEP button and follow prompt instructions from the picker. (Or use VSWEEP command.)
Meshing
...Sweep Meshing
Tet-Mesh Option A useful sweep option is to generate a tet-mesh in non-sweepable volumes. To use this option:
Make sure that the element type supports degenerate pyramid and tetrahedron shapes. Examples:
Training Manual
Meshing
...Sweep Meshing
Notes
Training Manual
To map-mesh a complex volume, you may need to slice it several times and also do some area and line concatenations. For sweep meshing, you typically need only a few slicing operations, and no concatenations are needed! You can control the source area mesh using standard mesh controls. SmartSizing is generally not recommended since it is meant for free meshing.
Meshing
...Sweep Meshing
Demo:
Resume ribvol.db
Training Manual
Meshing
H. Workshop
This workshop consists of four exercises:
W8A. Pillow Block
Training Manual