Professional Documents
Culture Documents
Product name E - N 4 Index of Technical Data Sheet. Product name N - S 5 Index of Technical Data Sheet. Product name S - U
* Please click on an above Index which you want to see.
click
click
2. To return to the front page, please click the Sheet index page.
3. To return to the Data Sheet index page, please click the of the Product Data Sheet pages.
Version Information
The Technical Data Sheet are edited as of April 2007 and these information are subject to revision from time to time wishout any notice. For the latest information please contact CMP.
A
ACRI 700 FINISH J ACRI 700 PRIMER J ALP 500
B
BANNOH 200 QD BANNOH 200 BANNOH 2000 QD BANNOH 2000 BANNOH 500 BANNOH 500 AC BANNOH 500 N BANNOH 500QD BANNOH 500R BIOCLEAN DX BIOCRYSTY 700 BIOCRYSTY ANZEN BIOGUARD C-3 BISCON AF BISCON HB-NT L BISCON HB-NT L QD BITUMEN SOLUTION B BONDET PUTTY 5127 5127 5083 5082 5055 5051 5073 5056 5072 5941 8283 8279 8285 5610 6135 6135 8440 9050 A
A A B
C
CERABEST CERABOND 2000 CERABOND TU CERABOND TU QL CLEANKEEP 201 CLEANKEEP 5000 CLEANKEEP 5000 HOLDING PRIMER CLEANKEEP 5500 CMP BIOCLEAN HB CMP BIOCLEAN SEALERCOAT 8052 1049 1034 1035 6073 6072 6075 6072 5982 5983 A A B A
E
EPICON MARINE CH EPICON MARINE HB EPICON MARINE UNDERCOAT M EPICON T-500 EPICON T-500 FOR REPAIR 5409 5402 5301 6025 6025 R
E
EPICON T-500 HS EPICON T-500 PRIMER H EPICON T-800 EPICON T-800 HOLDING PRIMER EPICON T-800 HS EPICON ZINC RICH PRIMER B-2 EPICON ZINC RICH PRIMER B-2 QL ETCHING PRIMER H ETCHING PRIMER H ( for Peller Clean Set Jr) ETCHING PRIMER H ( for Peller Clean Set) EVAMARINE EVAMAX 100P A
A Q P A
G
GALBON SP GALBON S-HB 6240 6250
H
HIPER AC 4005
L
LZI PRIMER LZI PRIMER ZR-HB LZI PRIMER ZS HB 2100 2104 A 2107
M
MARINE STAR 10 KAI MARINE STAR 20 KAI MARINE STAR A MARINE STAR FLAT S MAXSTOP G 2107 A 5876 B 5895 5968 S 6437
N
NEW MARINE GOLD DX NEW MARINE GOLD NOVA 1000 NOVA 1000 QD NOVA 2000 NOVA 2000 CH QD NOVA 2000 CH NOVA 2000 GF QD NOVA 2000 GF 5897 5896 6180 6180 6181 6181 6181 6181 6181
A I H F G
N
NOVA 2000 QD NOVA 2000 W QD NOVA 5000 NOVA 5000 BARRIER NZ PRIMER S
P
PERMAX No. 3000 S W PERMAX No. 3000 S PERMAX No. 3000 MU PERMAX No. 3000 MU W POLIBI T-1 6050 A 6050 6057 6059 3040
R
RAVAX FINISH RAVAX PRIMER RAVAX AC HB RAVAX AF ROSWAN QD ROSWAN QD HB ROSWAN QD ZR HB ROSWAN QD ZS HB RUST INHIBITIVE OIL "CK" RUST INHIBITIVE PRIMER Z 4400 4100 4001 4010 2130 2131 2134 2136 8250 2110
S
SEA FRONTIER SEA FRONTIER F SEA FRONTIER H SEA FRONTIER S SEA FRONTIER ME SEA GRANDPRIX 1000 SEA GRANDPRIX 2000 SEA GRANDPRIX 300 SEA GRANDPRIX 330 SEA GRANDPRIX 500 SEA GRANDPRIX 500 M SEA GRANDPRIX 800 SEA GRANDPRIX CF MK II SEA GRANDPRIX CF MK II L SEA GRANDPRIX CF SUPER SEA GRANDPRIX CF SUPER NFD 5917 5922 5919 5921 5917 5909 5911 5901 5902 5905 5905 5912 5830 5831 5921 5971 N N N N M
S
SEA GRANDPRIX CF-10 SEA GRANDPRIX CF-10 L SEA GRANDPRIX CF-10 L M SEA GRANDPRIX CF-10 M SEA GRANDPRIX CF-20 SEA GRANDPRIX FRP SEAJET 015 SEAJET 033 SEAJET 132 SEAJET 137 SEAJET 145W SILICON HR PRIMER SILICON HR SILVER HG SILICON HR SILVER SILICON HR SILVA SPAR No. 500 SILVAX SQ-K SILVAX SQ-M
T
TFA FLAT TFA-10 5873 5865 G
U
UMEGUARD PU UMEGUARD PU-TU UMEGUARD SUPUR H UMEGUARD SUPER H PRIMER UMEGUARD SUPER-H PRIMER QD UMEGUARD SX UMEGUARD SX HS UMEGUARD SX HS QD UNY MARINE 6165 6164 6197 6195 6196 6166 6193 6135 W 5510 A
Feb.2006
No. 4038J
700 FC J
ACRI 700 FINISH J is a finishing coat based on acrylic resin and drying by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention.
TECHNICAL DATA
Type
Acrylic finish paint
Recommened Finishing coat on ships' topside, superstructure Use
Information
White, As specified 24.0 [degC] 40 (+-2) [volume %] 545 [g/L] 2 0.075 - 0.1 [L/m ] : WET 75 - 100 [micron] DRY 30 - 40 [micron]
5 C 1.5hrs. 8hrs. 10hrs. o
(D.F.T. 35micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)60[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 6 % by Volume ACRI 700 PRIMER, BANNOH 200, BANNOH 500, BISCON HBNT-L -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 4037J
700 P J
ACRI 700 PRIMER J is an effective anti-rust primer based on acrylic resin and drying by evaporation of the solvents.It can be applied directly to bare steel or existing paint film such as acrylic, chlorinated rubber and epoxy. It has also good workability and it is possible to obtain thick coat especially by spray application.
TECHNICAL DATA
Type
Acrylic anti-rust primer
Recommened Anti-rust primer for exposure parts Use
Information
Light gray 24.0 [degC] 43 (+-2) [volume %] 492 [g/L] 2 0.093 - 0.186 [L/m ] : WET 93 - 186 [micron] DRY 40 - 80 [micron]
5 C 1.5hrs. 12hrs. 18hrs. o
(D.F.T. 60micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GRACO)721,723 Paint Output Pressuer: 11.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 10 % by Volume NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, CERABOND, etc. ACRI 700 FINISH J
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ALP 500
ALP
Mar.2006
No. 5006
500
ALP 500 is used as epoxy primer for aluminum on ship's hull, superstructure and other parts. It is a highly effective paint system with excellent adhesion property on aluminum surfaces, and has excellent salt water resistance and excellent applicability, high build efficiency.
TECHNICAL DATA
Type
Epoxy paint
Recommened As a primer on aluminum Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 66 : 34 [by volume] Light gray Base = 22.5, Hardener = 26.5 [degC] 58 (+-2) [volume %] 410 [g/L] 2 0.086 - 0.216 [L/m ] : WET 86 - 216 [micron] DRY 50 - 125 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)170[sec]
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 10 % by Volume UNY MARINE, VINYL AC-HB, etc.
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH
B
200 QD
200 QD
Feb.2006
No. 5127A
BANNOH 200 QD, based on a combination of modified epoxy resin and rust-preventive pigment, has excellent adhesion property, toughness and effective rust-preventive property. It is suitable for protection of superstructures and exposed deck of steel ships, and suitable for the application at cold weather.
TECHNICAL DATA
Type
Modified epoxy rust-preventive paint, high-build
Recommened Primer on inside and outside of superstructures, exposed deck of steel ships and other steel Use structures
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 76 : 24 [by volume] White, Grey, Green Base = 23.7, Hardener = 27.0 [degC] [volume %] 415 [g/L] 2 0.085 - 0.339 [L/m ] : WET 85 - 339 [micron] DRY 50 - 200 [micron]
5 C 3hrs. 20hrs. 16hrs. 8hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
30 C
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 1.5Pas
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. EPICON MARINE HB, UNY MARINE, RAVAX FINISH, etc.,
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 200
B
Feb.2006
No. 5127
200
BANNOH 200, based on a combination of modified epoxy resin and rust-preventive pigment, has excellent adhesion property, toughness and effective rust-preventive property. It is suitable for protection of superstructures and exposed deck of steel ships.
TECHNICAL DATA
Type
Modified epoxy rust-preventive paint, high-build
Recommened Primer on inside and outside of superstructures, exposed deck of steel ships and other steel Use structures
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 76 : 24 [by volume] White, Grey, Light grey, N8 Base = 23.7, Hardener = 27.0 [degC] 59 (+-2) [volume %] 419 [g/L] 2 0.085 - 0.339 [L/m ] : WET 85 - 339 [micron] DRY 50 - 200 [micron]
5 C 3.5hrs. 30hrs. 24hrs. 18hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 1.5Pas
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. EVAMARINE, RAVAX FINISH, ACRI 700 FINISH, UNY MARINE, EPICON MARINE HB, POLIBI T-1, etc.
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 2000 QD
B2000
Jul.2006
No. 5083
QD
BANNOH 2000 QD, is a multi-purpose high solid epoxy primer, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most of areas of ship as Universal primer.
TECHNICAL DATA
Type
Polyamine adduct cured epoxy
Recommened Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 75 : 25 [by volume] Pink, Light grey Base = 32.5, Hardener = 27.0 [degC] 80 (+-2) [volume %] 244 [g/L] 2 0.125 - 0.312 [L/m ] : WET 125 - 312 [micron] DRY 100 - 250 [micron]
5 C 7hrs. 17hrs. 17hrs. * 6hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNNER, Thinning: 0 - 7 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. BANNOH 500 N, UNYMARINE, EPICON MARINE HB, etc.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 2000
B2000
Jul.2006
No. 5082
BANNOH 2000, is a multi-purpose high solid epoxy primer, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most of areas of ship as Universal primer.
TECHNICAL DATA
Type
Polyamine adduct cured epoxy
Recommened Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 75 : 25 [by volume] Pink, Light grey Base = 32.5, Hardener = 27.0 [degC] 80 (+-2) [volume %] 261 [g/L] 2 0.125 - 0.312 [L/m ] : WET 125 - 312 [micron] DRY 100 - 250 [micron]
5 C 10hrs. 28hrs. 28hrs. * 8hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNNER, Thinning: 0 - 7 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. BANNOH 500 N, UNYMARINE, EPICON MARINE HB, etc.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500
B
Feb.2006
No. 5055
500
BANNOH 500, is a multi-purpose primer,which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most areas of ship.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Grey, Light Grey, Red brown, Black Base = 23.1, Hardener = 24.9 [degC] 63 (+-2) [volume %] 401 [g/L] 2 0.16 - 0.32 [L/m ] : WET 159 - 317 [micron] DRY 100 - 200 [micron]
5 C 7hrs. 24hrs. 24hrs. * 18hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, BANNOH THINNER Thinning: 0 - 15 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. BANNOH 500 N, BANNOH 500 AC, SILVAX SQ-K.M, EPICON MARINE HB
Packaging Notes
Two pack product 1.* Kindly consult with CMP sales office. 2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 3.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 AC
B
Mar.2007
No. 5051
500 AC
BANNOH 500 AC, is Tar free ,multi-purpose primer, based on special epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, etc. and highly resistant to water, and salt water. It is suitable for outside hull ,deck and superstructure of ships.
TECHNICAL DATA
Type
Tar free epoxy paint
Recommened Anti-corrosive for ships, and also where anti-abrasive property is specially required. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] Grey, Red brown Base = 23.1, Hardener = 24.9 [degC] 65 (+-2) [volume %] 382 [g/L] 2 0.16 - 0.31 [L/m ] : WET 154 - 308 [micron] DRY 100 - 200 [micron]
5 C 7hrs. 24hrs. 24hrs. (30) 18hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min (urethaen) Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume CERABOND, EPICON ZINC RICH PRIMER, BANNOH 500, etc. SILVAX SQ-K.M, EPICON MARINE HB, etc.
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 N
B
Feb.2006
No. 5073
500 N
BANNOH 500 N, is Tar free ,epoxy anti-corrosive primer, based on epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, especially excellent adhesion with anti-fouling paint.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint for ship's bottom Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Plum Base = 21.2, Hardener = 22.7 [degC] 54 (+-2) [volume %] 444 [g/L] 2 0.18 [L/m ] : WET 185 [micron] DRY 100 [micron]
-5 C 10hrs. 48hrs. 48hrs. o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 10 % by Volume BANNOH 500 SEA GRANDPRIX 1000,2000 , etc.
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 QD
B
Jul.2006
No. 5056
500 QD
BANNOH 500 QD, is a multi-purpose primer,which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most areas of ship. It is suitable for the application at cold weather.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Grey, Ligt Grey, Red brown, Black Base = 23.1, Hardener = 24.9 [degC] 63 (+-2) [volume %] 394 [g/L] 2 0.16 - 0.32 [L/m ] : WET 159 - 317 [micron] DRY 100 - 200 [micron]
-5 C 10hrs. 36hrs. 36hrs. *
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume CERABOND, EPICON ZINC RICH PRIMER, etc. BANNOH 500 N, SILVAX SQ-K.M, EPICON MARINE HB, etc.
Packaging Notes
Two pack product 1.* Kindly consult with CMP sales office. 2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases. 4.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 10 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 R
B
Feb.2006
No. 5072
500 R
BANNOH 500 R, is Tar free ,epoxy anti-corrosive primer, based on epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, especially excellent adhesion with anti-fouling paint. It is suitable for outside hull, deck and superstructure of ships.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint for repar ships Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Grey Base = 22, Hardener = 23.5 [degC] 60 (+-2) [volume %] 390 [g/L] 2 0.12 - 0.29 [L/m ] : WET 125 - 292 [micron] DRY 75 - 175 [micron]
5 C 5hrs. 24hrs. 18hrs.
o
(D.F.T. 175micron) Drying Time Surface Dry Hard Dry Painting Interval Min * Max * Pot Life
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0Pas
: : :
Tip No. : (GRACO)423,425,427 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, BANNOH THINNER Thinning: 0 - 5 % by Volume EPICON ZINC RICH PRIMER, etc. SEA GRANDPRIX 1000,2000 , RAVAX FINISH, EPICON MARINE FINISH, etc.
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCLEAN DX
Feb.2006
No. 5941
BIOCLEAN DX is an innocuous long life anti-fouling paint to prevent attachment of marine organisms by the effect of low critical surface tension of the surface of coated film. It has the following advantages: 1. Environmentaliy friendly, safe and hygienic 2. Good anti-fouling property 3. Easy application
TECHNICAL DATA
Type
Recommened Use
Special synthetic resin anti-fouling coating with an outstanding long term durability Anti-fouling for propeller of ship
Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Information
Clear 26.0 [degC] 84 (+-2) [volume %] 130 [g/L] 2 0.088 [L/m ] : WET 89 [micron] DRY 75 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 70 - 80[sec]
: : :
Tip No. : (GRACO)617,719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] SILICON THINNER, Thinning: 0 - 5 % by Volume ETCHING PRIMER H
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCRYSTY 700
BIOCRYSTY
Feb.2006
No. 8283
700
BIOCRYSTY 700 is a epochal anti-foulant for firming fishnet specially designed for the prevention of sticking barnacle and mussel moss animals with a cuprous glass type anti-foulant which developed by Chugoku Marin Paints originally. Specific Features Good anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons. Good workability and drying property for net-dyeing. No bad smelling, only solvent smell. Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type
Copper type anti-fouling paint
Recommened Fishnet Use
Information
Color Flash Point Specific Gravity VOC Thinner Consumption Weight Increase
Dark brown 26.0 [degC] 1.02(+-0.05) [g/mL] 704 [g/L] BIOCRYSTY THINNER : about 44 - 54 % (against fishnet weight) : 12 - 16 % (Dry)
: : : : :
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCRYSTY ANZEN
ANZEN
Feb.2006
No. 8279
BIOCRYSTY ANZEN is a epochal anti-foulant for firming fishnet specially designed for the prevention of sticking barnacle and mussel moss animals with a cuprous glass type anti-foulant which developed by Chugoku Marin Paints originally. Specific Features Good anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons. Good workability and drying property for net-dyeing. No bad smelling, only solvent smell. Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type
cuprous glass type anti-fouling paint
Recommened Fishnet Use
Information
Color Flash Point Specific Gravity VOC Drying Time Thinner Consumption Weight Increase
Dark brown 31.5 [degC] 1.07(+-0.05) [g/mL] 762 [g/L] 20 degC / 3 hrs. BIOCRYSTY THINNER : about 70 - 80 % (against fishnet weight) : 20 - 30 %
: : : : : :
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOGUARD C-3
C-3
Jan.2006
No. 8285A
BIOGUARD C-3 is a epochal anti-foulant for fishnet specially designed for the prevention of sticking hydrozoan with a organic nitorogenous sulfur type anti-foulant which developed by Chugoku Marin Paints originally. Specific Features Good anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons. Good workability and drying property for net-dyeing. No bad smelling, only solvent smell. Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type
Organic nitrogenous sulfur type anti-fouling paint
Recommened Fishnet Use
Information
Color Flash Point Specific Gravity VOC Drying Time Thinner Consumption Weight Increase
Black, White, Orange, 26.0 [degC] 0.96(+-0.05) [g/mL] 658 [g/L] 20 degC / 3 hrs. BIOGUARD THINNER, : about 30 - 35 % (against fishnet weight) : 9 - 10 % (Dry)
: : : : : :
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON
BC
AF
AF
Mar.2006
No. 5610
BISCON AF is a synthetic rubber vehicle based anti-fouling paint with a high content of antifoulant. It provides very effective and extended protection against fouling and results in fuel saving and elimination of lost time as well as loss of speed usually resulting from fouling.
TECHNICAL DATA
Type
Synthetic rubber anti-fouling paint
Recommened Anti-fouling finish of steel ship's bottom and underwater areas Use
Information
Red brown 27.0 [degC] 53 (+-2) [volume %] 404 [g/L] 2 0.075 - 0.094 [L/m ] : WET 75 - 94 [micron] DRY 40 - 50 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
: : :
Tip No. : (GRACO)619,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON AF THINNER, Thinning: 0 - 5 % by Volume RAVAX AC, RAVAX AC-HB, RAVAX AC S-HB, SILVAX SQ-HB, etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON
BC
HB NT L
HB-NT
Feb.2006
No. 6135A
BISCON HB-NT L, is a epoxy type paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil.
TECHNICAL DATA
Type
Epoxy type paint
Recommened Cargo hold, Inside and outside of accommodation space, Void space, Cofferdam, Engine room, Use Pipe line, Other steel structures, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Grey, Black, White, Red brown, Green Base = 23.5, Hardener = 19.0 [degC] 57 (+-2) [volume %] 426 [g/L] 2 0.176 - 0.439 [L/m ] : WET 176 - 439 [micron] DRY 100 - 250 [micron]
5 C 4.5hrs. 44hrs. 44hrs. 24hrs.
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON THINNER, Thinning: 0 - 5 % by Volume WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.Waiting time before the first dry cargo loading Temp. 10degC 20degC 30degC (Days) 20 12 7 3.As nature of epoxy coatings Biscon HB-NT L can not avoid chalking and fading on UV exposure.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON HB-NT L QD
BC
Feb.2006
No. 6135B
HB NT L QD
BISCON HB-NT L QD, is a epoxy type paint. It gives excellent physical properties such as adhesion , toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil. In addition , it has excellent drying properties at low temperatures.
TECHNICAL DATA
Type
Epoxy type paint
Recommened Cargo hold, Inside and outside of accomdation space, Void space, Cofferdam, Engine room, Pipe Use line, Other steel structures, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Grey, Black, White, Red brown Base = 23.5, Hardener = 19.0 [degC] 57 (+-2) [volume %] 435 [g/L] 2 0.176 - 0.439 [L/m ] : WET 176 - 439 [micron] DRY 100 - 250 [micron]
-5 C 8hrs. 40hrs. 40hrs. o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER -
Packaging Notes
Two pack product 1. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 2.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 3.Too much solvent results in reduced sag resistance and paint film property. 4.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases. 5.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 10
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BITUMEN SOLUTION B
BS
Feb.2007
No. 8440
BITUMEN SOLUTION B is a bituminous paint which has excellent adhesion properties to steel plates. BITUMEN SOLUTION B is used as a primer for Liquid Bitumen Enamel, and may be applied by itself as a temporary anti-corrosive paint.
TECHNICAL DATA
Type
Bituminous paint
Recommened As a protective coating for steel structures and inside of rudders, etc. Use
Information
Black 31.0 [degC] 41 [volume %] 499 [g/L] 2 0.073 - 0.121 [L/m ] : WET 73 - 121 [micron] DRY 30 - 50 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 0.7Pas
: : :
Tip No. : (GRACO)515,517 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BONDET PUTTY
BP
Feb.2006
No. 9050
BONDET PUTTY, based on epoxy resin and polyamide resin combination, has excellent physical properties such as adhesion, impact and abrasion resistance, etc., and chemical resistance to salt water, oil, alkalis and dilute acid, and is suitable for putty of tank interiors and underwater areas.
TECHNICAL DATA
Type
Epoxy/Polyamide putty
Recommened As protective coating against galvanic corrosion around the anode, and touching up of pitting Use corrosion occurring on exterior hull and tank inside.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 64 : 36 [by volume] Grey Base = -, Hardener = - [degC] 100 [volume %] 0 [g/L] 2 2 [L/m ] : WET 2000 [micron] DRY 2000 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Spatula Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. Thinner : EPICON MARINE THINNER (For cleaning), Preceding Coats Subsequent Coats : :
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABEST
Cb
Sep.2006
No. 8052
CERABEST is a combination of strictly selected heat resistant alloys and heat resistant silicate solution. It has excellent heat resistance at high temperatures up to 800 degC, and has excellent adhesion to inorganic zinc shop primer.
TECHNICAL DATA
Type
Ultra heat resistant paint
Recommened As a topcoat of inorganic shop primer to prevent from the heat damages of steel structures, Use such as Ships' super structures.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Paste : Base = 44 : 56 [by volume] Grey Paste = 13.6, Base = 13.0 [degC] 45 [volume %] 553 [g/L] 2 0.071 [L/m ] : DRY 30 [micron]
5 C 12mins. 60hrs. 14days 180days 30hrs.
o
(D.F.T. 30micron) Drying Time Surface Dry Hard Dry Painting Interval Min Organic Max Pot Life
Condition of Application
Method of Application : Airless spray, Air spray Weather : Temperature : 5 - 35 degC, Humidity : 50 - 90 %R.H. For Airless Spray : Viscosity : (IWATA CUP)9 - 10[sec]
Thinner
: :
Tip No. : (GRACO)619,719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 30 - 50[cm/sec] INORGANIC SHOP PRIMER THINNER, INORGANIC SHOP PRIMER THINNER S Thinning: 0 - 5 % by Volume inorganic shop primer Epoxy paint, Tar-epoxy paint, Non-tar-epoxy paint, Chlorinated rubber primer, Alkyd primer
Packaging Notes
Two pack product 1.To obtain homogenous mixture stir the PASTE well prior to adding the BASE. 2.To prevent from nozzle clogging, put 80 mesh filter on the suction inlet. 3.To prevent from pigment settling, keep stirring the mixture during the application. 4.Since the paint mixture reacts with moisture, use up the mixture as soon as possible under high humid condition. 5.Use the specified thinner. 6.Take 7 days for aging before application of subsequent coat at below 10 degree C since curing of the product becomes considerably slow at low temperature.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND 2000
CB
Mar.2007
No. 1049A
2000
CERABOND 2000 is a combination of heat resistant alloy and heat resistant silicate solution producing an inorganic rust preventive coat mechanically adhered to the steel and giving an effective and long-term protection against corrosion without suffering from blistering and loss of adhesion. It is compatible with organic overcoatings as well as with inorganic overcoatings. CERABOND 2000 is extremely resistant to heat (up to 800 degree C) and secondary surface preparation cost can be decreased. It has excellent welding and cutting properties and presents no health hazard to the welder. CERABOND 2000 has been approved by Lloyd's Register of Shipping as a shop primer which is suitable for welding.
TECHNICAL DATA
Type
Fast weldable & heat resistant inorganic zinc silicate shop primer
Recommened As a shop primer for temporary protection of blast-cleaned steel, as a general purpose Use rust-preventing primer for organic and inorganic over-coating, and also as a heat resistant paint.
Information
Mixing Ratio : Color : Flash Point : Specific Gravity : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Paste : Base = 39 : 61 [by volume] Green, Grey, Light grey, Brown, Grey S Paste = 23.3, Base = 13.0 [degC] 1.31 [g/mL] 36 1 [volume %] 606 [g/L] 2 0.044 [L/m ] : DRY 15 [micron]
5 C 3mins. 2hrs. 14days 16hrs. 36hrs.
o
(D.F.T. 15micron) Drying Time Surface Dry Hard Dry Painting Interval Min Organic Inorganic Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : 0 - 40 degC, Humidity : 50 - 90 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 11[sec]
Thinner
Tip No. : (GRACO)617 - 923 Paint Output Pressuer: 3.8 - 8.9[MPa] Spray Speed : 100 - 160[cm/sec] INORGANIC SHOP PRIMER THINNER, INORGANIC SHOP PRIMER THINNER S Thinning: 5 - 25 % by Volume Most our products or the equivalents. However, when oleoresins paints are applied please consult us . ; about 6 months
: :
Packaging Notes
Two pack product 1.Expected life for outdoor exposure (under normal conditions)
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
2.Oleoresinous coating system over CERABOND 2000 is no recommended on high humid (often sweaty) or underwater areas. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND TU
CB
Nov.2006
No. 1034A
TU
CERABOND TU, a two-pack primer, based on a combination of metallic zinc, epoxy resin and hardener. It dries quickly and gives adequate preliminary protection of steel. This primer is completely compatible with almost any type of paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type
Epoxy zinc rich primer
Recommened As a primer for protection of blast-cleaned steel plates used for under water area of outer hull Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 70 : 30 [by volume] Grey Base = 10.0, Hardener = 10.0 [degC] 40 (+-2) [volume %] 512 [g/L] 2 0.045 [L/m ] : DRY 18 [micron]
5 C 8mins. 4hrs. 24hrs. 180days 72hrs.
o
(D.F.T. 18micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.2 - 11[MPa] Spray Speed : 60 - 160[cm/sec] EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume (for airless spray) Most of our products or the equivalents except oleoresins paints.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND TU QL
CB
Feb.2006
No. 1035B
TU QL
CERABOND TU QL, a two-pack primer, based on a combination of metallic zinc, epoxy urethane resin and a hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with tar-urethane and vinyl-tar anti-corrosive paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type
Epoxy urethane zinc rich primer
Recommened As a primer for protection of blast-cleaned steel plates. For the application at low temperature. Use (-5 - +15C)
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] Grey Base = 6.0, Hardener = 6.0 [degC] 44 (+-2) [volume %] 486 [g/L] 2 0.041 [L/m ] : DRY 18 [micron]
5 C 4mins. 2hrs. 16hrs. 180days 6hrs.
o
(D.F.T. 18micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 15 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec] EPICON ZINC RICH PRIMER QL THINNER, Thinning: 10 - 25 % by Volume (for airless spray) Tar-urethane anti-corrosive paint, Vinyl-tar anti-corrosive paint, Chlorinated rubber anti-corrosive paint, etc.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 201
CK
Nov.2005
No. 6073A
201
CLEANKEEP 201, based on non-solvent type epoxy resin, is a special coating for drinking water tank interior. It has the following advantages; 1.Non-toxic, non -solvent and odourless 2.Good adhesiveness to various water tank substrates 3.Fast drying 4.Tough, glossy and smooth surfaces 5.Easy application with roller 6.Safe and hygienic since it is non-solvent type 7.Thick film can be formed with one coat. 8.Good anti-corrosive property with the barrier effect because of it's thick solid paint film
TECHNICAL DATA
Type
Non-solvent epoxy coating
Recommened As a interior coating for drinking water tank Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 73 : 27 [by volume] Blue Base = 136, Hardener = 126 [degC] 100 2 [volume %] 5 [g/L] 2 0.2 [L/m ] : WET 200 [micron] DRY 200 [micron]
5 C 16hrs. 24hrs. 24hrs. 5days 90mins. 48hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life Dry to Launch Min
Condition of Application
Method of Application : Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 5.0 - 8.0 Pas Thinner : , Preceding Coats Subsequent Coats : :
Thinning: - % by Volume -
Packaging Notes
Two pack product 1."bis-phenol A type" epoxy resin is not used in this paint. 2.Please use summer type hardener in summer or high temperature environment. 3.Do not use any thinner for application. 4.Mixing ratio of Base and Hardener by weight = 4 : 1 5.Mix materials as required, because of short pot life.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
6.Surface preparation : In case of direct application on steel surface, ISO St3 or more is required.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 5000
CK
Mar.2007
No. 6072
5000
CLEANKEEP 5000, solvent-free epoxy paint, is designed as a protective coating of drinking water tank. CLEANKEEP 5000 is friendly to the environment as it provides no solvent, no heavy metal and less wasted material while coating. CLEANKEEP 5000 could be coated by airless spray.
TECHNICAL DATA
Type
Solventfree epoxy coating
Recommened Fresh water tank, Drinking water tank, Portable water tank Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Cream, Light grey Base = >250, Hardener = 155 [degC] 100 (+-2) [volume %] 80 [g/L] 2 0.3 [L/m ] : WET 300 [micron] DRY 300 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 3.0 - 4.0Pas
: : :
Tip No. : (GRACO)619 - 721 Paint Output Pressuer: 23.5 - 33.4[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER ( for cleaning only ), Thinning: - % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER -
Packaging Notes
Two pack product 1.Certificated by the test of quality fo Drinking Water as follows: 2. - Tests of Effect on Water Quality/BS 6920: 2000- WRAS(UK) 3. - SS375: 1994- SINGAPORE 4. - Ministry of Health Circular no.102/78: 2001- ITALY 5. - Hiroshima City Research Laboratory of Public Health - Japan
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Jul.2006
No. 6075
5000 HP
CLEANKEEP 5000 HOLDING PRIMER, based on a combination of epoxy resin and hardener, has excellent physical properties such as adhesion, toughness, abrasion resistance, and water resistance. It is particularly compatible with CLEANKEEP 5000 and useful as a holding primer for drinking water tank interiors.
TECHNICAL DATA
Type
Epoxy holding primer
Recommened As holding primer for drinking water tank interiors Use
Information
Mixing Ratio : Color : Flash Point : Specific Gravity : Solid by volume : Coverage(Theoretical): Film Thickness
Base : Hardener = 73 : 27 [by volume] Pink Base = 10.5, Hardener = 10.0 [degC] 1.16 [g/mL] 33 2 [volume %] 2 0.152 [L/m ] : WET 152 [micron] DRY 50 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 0.9 - 1.0Pas
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc. CLEANKEEP 5000
Packaging Notes
Two pack product 1.* In case of outdoor exposure. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 5500
CK
Feb.2006
No. 6072C
5500
CLEANKEEP 5500, solvent-free epoxy paint, is designed as a protective coating of drinking water tank. CLEANKEEP 5500 is friendly to the environment as it provides no solvent, no heavy metal and less wasted material while coating. CLEANKEEP 5500 could be coated by airless spray.
TECHNICAL DATA
Type
Solventfree epoxy coating
Recommened Fresh water tank, Drinking water tank, Portable water tank Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Cream, Light grey Base = >250, Hardener = 155 [degC] 100 (+-2) [volume %] 0 [g/L] 2 0.3 [L/m ] : WET 300 [micron] DRY 300 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Rion viscometer)3 - 4Pas
: : :
Tip No. : (GRACO)619 - 721 Paint Output Pressuer: 23.5 - 33.4[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER ( for cleaning only ), Thinning: - % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER -
Packaging Notes
Two pack product 1.Certificated by the test of quality fo Drinking Water as follows: 2.ANSI / NSF - Standard - 61 (USA) 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CMP BIOCLEAN HB
CMP
Apr.2007
No. 5982
BCL HB
TECHNICAL DATA
Type
Silicone elastomer
Recommened As a finish coat in the CMP BIOCLEAN foul release system. Use Especialiy designed for ocean going liners and fast coastal vessels.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base:Hardener:Accelerator = 75:20:5 [by volume] Light Grey Base = 34.5, Hardener = 25.0, Accelerator = 20.5 [degC] 68 (+-2) [volume %] 275 [g/L] 2 0.293 [L/m ] : WET 293 [micron] DRY 200 [micron]
5 C
o
(DFT 200microns) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : 10 - 35 degC, Humidity : 40 - 85 %R.H. For Airless Spray : Viscosity : -
: : :
Tip No. : (GRACO)617 - 719 Paint Output Pressuer: Minimum 20.0[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, (for cleaning only) Thinning: - % by Volume CMP BIOCLEAN SEALER COAT -
Packaging Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Apr.2007
No. 5983
BCL SC
CMP BIOCLEAN SEALER COAT is two pack sealer coat, which enables application of CMP BIOCLEAN system over self-polishing type of anti-fouling paints.
TECHNICAL DATA
Type
Modified epoxy paint
Recommened As a basecoat in the CMP BIOCLEAN foul release system Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] Grey Base = 23.1, Hardener = 24.9 [degC] 55 (+-2) [volume %] 382 [g/L] 2 0.154 [L/m ] : WET 154 [micron] DRY 100 [micron]
5 C 7hrs. 24hrs. 7hrs. 18hrs.
o
(DFT 100microns) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON THINNER, Thinning: 0 - 5 % by Volume SEA GRANDPRIX 500,1000,CF-10, BANNOH 500 etc. CMP BIOCLEAN SYSTEM
Packaging Notes
Two pack product 1.*Please refer to painting specification. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON MARINE CH
EPM
Feb.2006
No. 5409
CH
EPICON MARINE CH, based on a combination of epoxy resin and polyamide curing agent, has high-build excellent durability and adhesion properties. It is suitable for carhold.
TECHNICAL DATA
Type
Epoxy paint
Recommened Carhold, inside of steel superstructures, anticorosive finish coat Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] White (Standard) Base = 24.0, Hardener = 16.0 [degC] 58 (+-2) [volume %] 466 [g/L] 2 0.085 - 0.172 [L/m ] : WET 86 - 172 [micron] DRY 50 - 100 [micron]
5 C 4.5hrs. 45hrs. 28hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5Pas
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume BANNOH 500, BANNOH 200, etc. -
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.As nature of epoxy coatings EPICON MARINE CH can not avoid chalking and fading on UV exposure. 3.Please consult our representative about color variation 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON MARINE HB
EPM
Feb.2006
No. 5402
HB
EPICON MARINE HB, based on a combination of epoxy resin and polyamide curing agent, has high-build excellent durability and adhesion properties. It is suitable as a finish coat for protection of steel ships, bridges and steel structures.
TECHNICAL DATA
Type
Epoxy/Polyamide finish coat, high-build
Recommened Finish coat of EPICON MARINE system of steel ships, bridges and other steel structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 73 : 27 [by volume] As specified(except White) Base = 23.0, Hardener = 27.5 [degC] 58 (+-2) [volume %] 465 [g/L] 2 0.052 - 0.172 [L/m ] : WET 52 - 172 [micron] DRY 30 - 100 [micron]
-5 C 5.5hrs. 55hrs. 55hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5Pas
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume BANNOH 500, BANNOH 200, etc. -
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.As nature of epoxy coatings EPICON MARINE HB can not avoid chalking and fading on UV exposure. 3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 5301
UC M
EPICON MARINE UNDERCOAT M, based on a combination of modified epoxy resin and Polyamide curing agent, has excellent durability and adhesion properties. It is protective undercoat for steel ships, bridges and steel structures.
TECHNICAL DATA
Type
Modified epoxy/Polyamide undercoat
Recommened Undercoat of steel ships, bridges and other steel structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] Black, White Base = 24.5, Hardener = 27.5 [degC] 45 (+-2) [volume %] 505 [g/L] 2 0.088 - 0.131 [L/m ] : WET 88 - 131 [micron] DRY 40 - 60 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
: : :
Tip No. : (GRACO)619,719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume EPICON MARINE HB-AL, EPICON MARINE HB-CL, BANNOH BANNOH 500 AC, etc. RAVAX FINISH, UNY MARINE, etc.
200,
Packaging Notes
Two pack product 1.Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500
EP
Feb.2006
No. 6025
T-500
EPICON T-500, a high build type epoxy coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 75-125 microns per coat.
TECHNICAL DATA
Type
Epoxy tank coating, high-build
Recommened Product carrier tank, Cargo oil tank, Fresh water tank, Drinking water tank, Portable water tank, Use Hold, Solvent tank, Chemical tank, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 79 : 21 [by volume] Red brown, Grey, Light Grey, White Base = 13.0, Hardener = 15.5 [degC] 58 (+-2) [volume %] 423 [g/L] 2 0.13 - 0.216 [L/m ] : WET 130 - 216 [micron] DRY 75 - 125 [micron]
5 C 3.5hrs. 36hrs. 36hrs. 10days 5days 10hrs.
o
(D.F.T. 125micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5(10) degC, Humidity : Dew Point For Airless Spray :
Thinner
: :
+Minimum 5 degC Viscosity : 1 - 1.5 Pas Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON T-500 THINNER , EPICON T-500 S THINNER, EPICON T-500 THINNER for WINTER Thinning: 0 - 10 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, EPICON T-500 PRIMER H, EPICON T-500
Packaging Notes
Two pack product 1.Shown above "( )" are for tank coating of product carrier, please refer to Chugoku's catalogue "Product Carrier Tank Coating" in detail. 2.* Maximum painting interval is 3 days at 20degC when it is exposed outdoors. 3.** On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
4.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 6025R
EPICON T-500 FOR REPAIR, high build type epoxy coating, has excellent physsical properites such as adhesion, toughness, abrasion resistance, etc., and chemical resistance to salt water, petroleum products, crude oil, alkaris and weak acid, and is suitable as a protective coating of tank interior. A dry fil thickness of 8 - 10 mils can be built in brush application. It is suitable as a protective coating tank interior.
TECHNICAL DATA
Type
Epoxy tank coating, high-build
Recommened Cargo oil tank, fresh water tank, hold, solvent tank, chemical tank, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 77 : 23 [by volume] Red brown, Grey, Light Grey Base = 13.0, Hardener = 24.0 [degC] 59(+-2) [volume %] 342 [g/L] 2 0.128 - 0.213 [L/m ] : WET 128 - 213 [micron] DRY 75 - 125 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 7.5Pas Thinner : EPICON T-500 THINNER, Preceding Coats Subsequent Coats : :
Packaging Notes
Two pack product 1.Maximum painting interval at 20 degree C is 3 days when it is exposed outdoors. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500 HS
EP
Sep.2006
No. 6032
T-500 HS
EPICON T-500 HS, a high build type epoxy coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 100-125 microns per coat.
TECHNICAL DATA
Type
Epoxy tank coating, high-build
Recommened Cargo oil tank, solvent tank, chemical tank, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 77 : 23 [by volume] Red brown, Grey, Light Grey Base = 17.5, Hardener = 46.5 [degC] 74 (+-2) [volume %] 267 [g/L] 2 0.135 - 0.203 [L/m ] : WET 135 - 203 [micron] DRY 100 - 150 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Dew Point +Minimum For Airless Spray :
Thinner
: :
5 degC Viscosity : 1.3 - 1.8 Pas Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON T-500 THINNER , EPICON T-500 S THINNER, EPICON T-500 THINNER for WINTER Thinning: 0 - 10 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc. EPICON T-500 HS
Packaging Notes
Two pack product 1. On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Apr.2006
No. 6020A
T-500 H
EPICON T-500 PRIMER H, based on a combination of epoxy resin and hardener, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. and chemical resistance to salt-water, petroleum products, crude oil, alkalis and weak acids, and it is particularly compatible with EPICON T-500. When this product is used as a folding primer, please reference the Notes.
TECHNICAL DATA
Type
Epoxy tank coating
Recommened As primer for product carrier tank interiors and useful as holding primer Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 73 : 27 [by volume] Pink brown Base = 13.0, Hardener = 15.5 [degC] 33 (+-2) [volume %] 595 [g/L] 2 0.152 [L/m ] : WET 152 [micron] DRY 50 [micron]
10 C 90mins. 16hrs. 16hrs. 15days (7)days 24hrs.
o
(D.F.T. 50micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Dew Point +Minimum For Airless Spray :
Thinner
: :
5 degC Viscosity : 0.9 - 1Pas Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec] EPICON T-500 THINNER, EPICON T-500 S THINNER, EPICON T-500 THINNERfor WINTER Thinning: 0 - 5 % by Volume WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, etc. EPICON T-500
Packaging Notes
Two pack product 1.* In case of outdoor exposure. 2.In case of using as holding primer, please reference the following. Coverage 0.076L/m2 Film thickness WET:76micron, DRY:25micron (D.F.T 25micron) 10decC 20degC 30degC Drying time Surface Dry 15mins. 10mins. 6mins.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Hard Dry 3hrs. 2hrs. 1.5hrs. Painting Interval Min 16hrs. 12hrs. 8hrs. Max 15days 15days 15days Max * 7days 5days 3days Pot Life 16hrs. 10hrs. 6hrs. Viscosity Ford cup No.4 : 16 sec Thinning for airless spray : 0 - 10 % by Volume 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-800
EP
Feb.2006
No. 6037
T-800
EPICON T-800, a high-build type epoxy phenolic coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 75-125 microns per coat.
TECHNICAL DATA
Type
Epoxy phenolic tank coating, high-build
Recommened Product carrier tank, Chemical tank, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 84 : 16 [by volume] Grey, Light Grey, Red brown Base = 17.5, Hardener = 7.5 [degC] 63 (+-2) [volume %] 332 [g/L] 2 0.119 - 0.199 [L/m ] : WET 119 - 199 [micron] DRY 75 - 125 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Dew Point +Minimum For Airless Spray :
: : :
5 degC Viscosity : 1.0 - 1.5Pas Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON T-800 THINNER, Thinning: 0 - 10 % by Volume EPICON T-800 HOLDING PRIMER , EPICON T-800, WELBOND, EPICON ZINC RICH PRIMER EPICON T-800
CERABOND,
Packaging Notes
Two pack product 1.* In case of outdoor exposure. 2. On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Apr.2006
No. 6035
T-800 HP
EPICON T-800 HOLDING PRIMER, based on a combination of epoxy phenolic resin, rust-preventive pigments and hardener, has chemical resistance to salt-water, petroleum products, crude oil, alkalis and weak acids. It is particularly compatible with EPICON T-800 and useful as a holding primer for product carrier tank interiors.
TECHNICAL DATA
Type
Epoxy phenolic holding primer
Recommened As a holding primer for product carrier tank interiors Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Pink brown Base = 17.5, Hardener = 8.0 [degC] 35 (+-2) [volume %] 577 [g/L] 2 0.072 [L/m ] : WET 72 [micron] DRY 25 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Dew Point +Minimum For Airless Spray :
: : :
5 degC Viscosity : (Fc#4)9 - 10[sec] Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec] EPICON T-800 THINNER, Thinning: 0 - 20 % by Volume CERABOND, WELBOND EPICON T-800
Packaging Notes
Two pack product 1.* In case of outdoor exposure. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-800 HS
EP
Oct.2006
No. 6033
T-800 HS
EPICON T-800 HS, a high-solid type epoxy phenolic coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 100-150 microns per coat.
TECHNICAL DATA
Type
Epoxy phenolic tank coating, high-solid
Recommened Product carrier tank, Chemical tank, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Red brown, Light Grey, Grey Base = 24.0, Hardener = 10.0 [degC] 77 2 [volume %] 264 [g/L] 2 0.13 - 0.195 [L/m ] : WET 130 - 195 [micron] DRY 100 - 150 [micron]
10 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Dew Point +Minimum For Airless Spray :
: : :
5 degC Viscosity : 1.3 - 1.7Pas Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 80[cm/sec] EPICON T-800 THINNER, Thinning: 0 - 10 % by Volume CERABOND, EPICON ZINC RICH PRIMER EPICON T-800 HS
Packaging Notes
Two pack product 1.Application of block is not recommended. If defumidification and temperature can not be controlled, application should not be carried out.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Nov.2006
No. 1034
B-2
EPICON ZINC RICH PRIMER B-2, a two-pack primer, based on a combination of metallic zinc, epoxy resin and hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with almost all type of coatings and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type
Epoxy zinc rich primer
Recommened As a primer for protection of blast-cleaned steel plates used for under water area of outer hull Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 70 : 30 [by volume] Grey Base = 10.0, Hardener = 10.0 [degC] 40 (+-2) [volume %] 512 [g/L] 2 0.045 [L/m ] : DRY 18 [micron]
5 C 8mins. 4hrs. 24hrs. 180days 72hrs.
o
(D.F.T. 18micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.2 - 11.0[MPa] Spray Speed : 60 - 160[cm/sec] EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume (for airless spray Most of our products or the equivalents except oleoresins paints.
Packaging Notes
Two pack product 1. * Minimum painting interval for touch up is 4 hours at 20degC 2.This primer has good workability and good adhesion with almost all type of over coatings. Therefore, this primer is suitable for touch-up coating. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 1035A
B-2 QL
EPICON ZINC RICH PRIMER B-2 QL, a two-pack primer, based on a combination of metallic zinc, epoxy urethane resin and a hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with tar-urethane and vinyl-tar anti-corrosive paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type
Epoxy urethane zinc rich primer
Recommened As a primer for protection of blast-cleaned steel plates. For the application at low temperature. Use (-5 - +15C)
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] Grey Base = 6.0, Hardener = 6.0 [degC] 44 (+-2) [volume %] 486 [g/L] 2 0.041 [L/m ] : DRY 18 [micron]
-5 C 8mins. 4hrs. 36hrs. 180days 10hrs.
o
(D.F.T. 18micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 15 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec] EPICON ZINC RICH PRIMER QL THINNER, Thinning: 10 - 25 % by Volume Tar-urethane anti-corrosive paint, Vinyl-tar anti-corrosive paint, Chlorinated rubber anti-corrosive paint, etc.
Packaging Notes
Two pack product 1.The temperature of the mixed base and hardener preferably should be above 0 degC otherwise extra solvent may be required to obtain appliaction viscosity. 2.Too much solvent results in reduced sag resistance. 3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ETCHING PRIMER H
ETP
Oct.2006
No. 1061
ETCHING PRIMER H is a two-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a temporary protection against corrosion and increasing the adhesive property of the subsequent coats.
TECHNICAL DATA
Type
Butyral resin based etching primer
Recommened As a pre-treatment primer on non-ferrous metals such as aluminium and light alloys as well as Use zinc and galvanized iron. May also be used as a pre-treatment primer on blast-cleaned steel plates
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Additive = 80 : 20 [by volume] Yellow Base = 17.5, Additive = 15.0 [degC] 10 [volume %] 703 [g/L] 2 0.08 [L/m ] : DRY 8 [micron]
5 C 20mins. 2hrs. 6hrs. 24hrs. 24hrs.
o
(D.F.T. 8micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)18 - 22[sec]
: : :
Tip No. : (GRACO)617 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 90 - 120[cm/sec] ETCHING PRIMER THINNER, Thinning: 35 - 50 % by Volume (for airless spray) Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 1061Q
ETCHING PRIMER H(for Peller Clean Set Jr) is a three-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a excellent adhesive property for propeller surfece and the subsequent coat . (Bioclean DX)
TECHNICAL DATA
Type
Butyral resin based etching primer
Recommened As a primer of Bioclean DX for propeller Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base:Additive:Adhisive agent = 4 : 1 : 1 [by volume] Yellow Base = 17.5, Additive = 15.0, Adhisive agent = 26.0 [degC] 10 [volume %] 726 [g/L] 2 0.08 [L/m ] : WET 86 [micron] DRY 8 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. Thinner : ETCHING PRIMER THINNER, Preceding Coats Subsequent Coats : :
Thinning: 35 - 50 % by Volume Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Three pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 1061P
ETCHING PRIMER H(for Peller Clean Set) is a three-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a excellent adhesive property for propeller surfece and the subsequent coat. (Bioclean DX)
TECHNICAL DATA
Type
Butyral resin based etching primer
Recommened As a primer of Bioclean DX for propeller Use
Information
: :
Base : Additive : Adhisive agent = 4 : 1 : 0.25 [by volume] Yellow Base = 17.5, Additive = 15.0, Adhisive agent = 26.0 [degC] 10 (+-2) [volume %] 706 [g/L] 2 0.08 [L/m ] WET 72 [micron] DRY 8 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. Thinner : ETCHING PRIMER THINNER, Preceding Coats Subsequent Coats : :
Thinning: 35 - 50 % by Volume Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Three pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EVAMARINE
EM
Feb.2006
No. 2400A
EVAMARINE is an alkyd resin based paint with excellent adhesion property, weathering resistance and excellent colour retention.
TECHNICAL DATA
Type
Alkyd resin finish paint
Recommened As a finishing coat on exterior wood and steel surfaces Use
Information
As specified, 43.0 [degC] 49 (+-2) [volume %] 385 [g/L] 2 0.051 - 0.071 [L/m ] : WET 51 - 71 [micron] DRY 25 - 35 [micron]
0 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)110[sec]
: : :
Tip No. : (GRACO)615,715 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume LZI PRIMER, RED LEAD PRIMER QD, EVAMARINE UNDERCOAT, etc. -
Packaging Notes
One pack product Applying within the recommended film thickness range to avoid the wrinkling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EVAMAX 100P
EX
Feb.2006
No. 6435
100P
EVAMAX 100P is based on a combination of epoxy resin, special abrasive resistant agent and polyamide resin. It provides excellent characteristics in adhesion, toughness, impact, abrasion resistance and rust-prevention. It is suitable for protection of exposed deck and holds of steel ships.
TECHNICAL DATA
Type
Epoxy/Polyamide, high-build
Recommened Ship's deck and hold Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 75 : 25 [by volume] Grey, Red brown Base = 21.2, Hardener = 30.5 [degC] 58 2 [volume %] 409 [g/L] 2 0.216 - 0.432 [L/m ] : WET 216 - 432 [micron] DRY 125 - 250 [micron]
5 C 4.5hrs. 44hrs. 44hrs. 90days 24hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2Pas
Spray Speed : 60 - 80[cm/sec] EVAMAX THINNER, Thinning: 0 - 5 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER EPICON MARINE FINISH
Packaging Notes
Two pack product 1. In confined spaces such as tank insides ventilation is required during application and curing to remove solvent vapours and promote curing. 2.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
GALBON SP
GB
Feb.2006
No. 6240
SP
GALBON SP is a combination of selected zinc dust and ethyl silicate solution producing an inorganic coat which gives outstanding prolonged weather resistance, effective and long-term protection against corrosion, solvent and oil resistance, heat resistance ( up to 400 decC), and resistance to fresh and salt water.
TECHNICAL DATA
Type
Inorganic zinc silicate alcohol soluble and self -curing
Recommened As a shop primer, as a protective coating for oil tanks, solvent tanks, ballast tanks, heating pipes, Use holds, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Powder = 76 : 24 [by volume] Grey Base = 14.5, Powder = - [degC] 39 [volume %] 464 [g/L] 2 0.051 [L/m ] : WET 51 [micron] DRY 18 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Air spray, Brush Weather : Temperature : 0 - 50 degC, Humidity : 50 - 95 %R.H. For Airless Spray : Viscosity : (Fc#4)11[sec]
: :
Subsequent Coats
Tip No. : (GARCO)719,721 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec] GALBON S THINNER, Thinning: 0 - 5 % by Volume The particular properties of this product require a very careful surface preparation of the steel which must be blast-cleaned to SSPC-SP 10 or ISO Sa 2.5. Any one of our products and/or the equivalent, e.g. Inorganic zinc paint, Chlorinated rubber paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
GALBON S-HB
GB
Feb.2006
No. 6250
S-HB
GALBON S-HB is an alcohol soluble inorganic zinc coating based on a combination of ethyl silicate and selected zinc dust. It gives excellent protection against corrosion and prolonged weather resistance, and is highly resistant to oil and solvent as well as fresh and salt water. GALBON S-HB withstands temperatures of up of to 400 degree C. A film thickness of 50-100 microns can be built in one application. GALBON S-HB is recommended as a top coating over GALBON S or WELBOND.
TECHNICAL DATA
Type
Inorganic zinc silicate alcohol soluble and self -curing, high-build type
Recommened As a protective coating for oil tanks, solvent tanks, ballast tanks, outside hull, deck, heating Use pipes, holds, other steel structures, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Powder = 7 : 3 [by volume] Grey Base = 14.5, Powder = - [degC] 60 2 [volume %] 464 [g/L] 2 0.083 - 0.125 [L/m ] : WET 83 - 125 [micron] DRY 50 - 75 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray; Brush (only for touch-up) Weather : Temperature : 0 - 50 degC, Humidity : 50 - 95 %R.H. For Airless Spray : Viscosity : 10 - 12[sec]
Spray Speed : 60 - 80[cm/sec] GALBON S-HB THINNER, Thinning: 0 - 5 % by Volume GALBON S, GALBON SP, WELBOND, CERABOND Any one of our products and/or the equivalent, e.g. Inorganic zinc paint, Chlorinated rubber paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Two pack product 1.In case an organic top coat is applied, dry film thickness of GALBON S-HB should be controlled at 50-100 microns. Recommended dry film thickness is 65 microns. 2.Waiting time before the first cargo loading for Bulkcarrier(DRY CARGO) Temp. 10degC 20degC 30degC (Days) 7 7 7 3.Mixing Ratio,Base:Powder=25:75(by weight)
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
HIPERAC
HP
Mar.2006
No. 4005
AC
HIPER AC is a special synthetic resin paint giving a high-build quick drying, effective protection against corrosion. It possesses good sea water resistance and shows good adhesion to subsequent coats.
TECHNICAL DATA
Type
Special synthetic resin anti-corrosive paint
Recommened Anti-corrosive paint for repair ships and steel ship's hull. Use
Information
S(Silver), SR(Silver red) 26.5 [degC] 43 (+-2) [volume %] 538 [g/L] 2 0.142 - 0.235 [L/m ] : WET 142 - 235 [micron] DRY 60 - 100 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min (AC) (AF) Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, etc. TFA-10,TFA-10H, TFA FLAT, SEATENDER 12.15, SEA GRANDPRIX 500,1000, etc.
Packaging Notes
One pack product 1.Below 10 degC, extra solvent maybe required to obtain application viscosity. 2.But too much solvent results in reduced sag resistance and paint film property.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
LZI PRIMER
LZI
Feb.2006
No. 2100
LZI PRIMER, is an alkyd resin based primer . It dries quickly, offering effective rust-prevention and excellent resistance to impact and bending.
TECHNICAL DATA
Type
Alkyd resin primer
Recommened As a rust-preventing primer for inside of superstructure, deck, hold, and other steel structures Use
Information
Red brown 43.0 [degC] 52 (+-2) [volume %] 383 [g/L] 2 0.058 - 0.077 [L/m ] : WET 58 - 77 [micron] DRY 30 - 40 [micron]
0 C 7hrs. 26hrs. 45hrs. 120days
o
(D.F.T. 35micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, etc. EVAMARINE, Alkyd resin based paints
Packaging Notes
One pack product 1.Applying within the recommended film thickness range to avoid the wrinkling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 2104A
ZR HB
LZI PRIMER ZR-HB, based on alkali-resistant synthetic resin, contains special compound which can make zinc surface stable. It has excellent adhesion property on zinc rich shop primer, as well as salt-water and weathering resistance.
TECHNICAL DATA
Type
Special synthetic resin primer
Recommened As the 1st coat of primer, when a conventional paint system is specified on zinc shop primer Use
Information
Red brown 36.0 [degC] 52 (+-2) [volume %] 388 [g/L] 2 0.058 - 0.135 [L/m ] : WET 58 - 135 [micron] DRY 30 - 70 [micron]
0 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pas
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, WELBOND, NZ PRIMER, etc. EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging Notes
One pack product 1.Applying within the recommended film thickness range to avoid the wrinkling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
LZI PRIMER ZS HB
LZI
Feb.2006
No. 2107
ZS HB
LZI PRIMER ZS HB, based on alkali-resistant synthetic resin, contains special compound which can make zinc surface stable. It has excellent adhesion property on zinc rich shop primer, as well as salt-water and weathering resistance.
TECHNICAL DATA
Type
Special synthetic resin primer, High build
Recommened As the 1st coat of primer, when a conventional paint system is specified on zinc shop primer Use
Information
Red brown 31.0 [degC] 43 (+-2) [volume %] 471 [g/L] 2 0.069 - 0.162 [L/m ] : WET 70 - 162 [micron] DRY 30 - 70 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray; Brush*; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, WELBOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc. LZI PRIMER, ROSWAN QD, HOLD SILVER, EVAMARINE, etc.
Packaging Notes
One pack product 1. * Sufficient thickness is difficult to obtain by brush. 2.** In case of applying alkyd resin finish coat on LZI PRIMER ZS HB at outdoor exposed area or high humidity area , LZI PRIMER or ROSWN QD to be applied as a binder coat 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5865A
10 KAI
MARINE STAR 10 KAI is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Pink, Red 23.0 [degC] 55 (+-2) [volume %] 476 [g/L] 2 0.18 - 0.27 [L/m ] : WET 182 - 273 [micron] DRY 100 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Nov.2006
No. 5876B
20 KAI
MARINE STAR 20 KAI is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint for steel ship's bottom Use
Information
Pink, Red 23.0 [degC] 54 (+-2) [volume %] 462 [g/L] 2 0.138 - 0.184 [L/m ] : WET 138 - 184 [micron] DRY 75 - 100 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MARINE STAR A
MS
Feb.2006
No. 5895
MARINE STAR A is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling peraformance.
TECHNICAL DATA
Type
Tin free antifouling paint
Recommened Antifouling paint on aluminum ship's bottom Use
Information
Red, Blue, Red brown, 22.0 [degC] 54 (+-2) [volume %] 421 [g/L] 2 0.186 [L/m ] : WET 186 [micron] DRY 100 [micron]
o
White
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume VINYL AC-HB, RAVAX AC, RAVAX AC-P, HIPER AC, etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5868S
FLAT S
MARINE STAR FLAT S is a tin free antifouling paint with self polishing action. The product is used for fouling control on the flat bottom.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ships' flat bottom for world wide service with extended drydocking Use interval.
Information
Pink, Red 23.0 [degC] 52 (+-2) [volume %] 457 [g/L] 2 0.095 - 0.19 [L/m ] : WET 95 - 190 [micron] DRY 50 - 100 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 633(733) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ, VINYL AC-HB, RAVAX AC-P, RAVAX AC, RAVAX AC-HB, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MAXSTOP G
MXT
Dec.2006
No. 6437
MAXSTOP G is a high-build epoxy non-slip paint. It has excellent physical properties such as adhesion, toughness, impact and abrasion resistance, and chemical resistance to water, salt water and oils. No repainting is required for long time. It is suitable for non-slip deck.
TECHNICAL DATA
Type
Epoxy paint, high-build
Recommened Non-slip deck coating Use
Information
Mixing Ratio : Color : Flash Point : Specific Gravity : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 82 : 18 [by volume] Red brown, Green, Grey Base = 34.0, Hardener = 29.3 [degC] 1.81 [g/mL] 75 2 [volume %] 233 [g/L] 2 1.07 [L/m ] : WET 1066 [micron] DRY 800 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Special spray equipment, Roller, Brush, Spatula Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. Thinner : MAXSTOP THINNER, EPICON MARINE THINNER Preceding Coats Subsequent Coats : :
Packaging Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NEW
NMG
DX
MARINE GOLD DX
Feb.2006
No. 5897
NEW MARINE GOLD DX is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on FRP,aluminium and steel ship's bottom . Use
Information
Red , Blue, Red brown, 24 [degC] 40 (+-2) [volume %] 530 [g/L] 2 0.12 - 0.25 [L/m ] : WET 124 - 262 [micron] DRY 50 - 100 [micron]
5 C 3hrs. 6hrs. 6hrs. 8hrs.
o
White
(D.F.T. 50micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Air spray; Brush; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume FRP PRIMER, VINYL AC-HB, HIPER AC, RAVAX AC-HB, SILVAX SQ-K, -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 5896
NEW MARINE GOLD is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling performance.
TECHNICAL DATA
Type
Tin free antifouling paint
Recommened Antifouling paint on FRP ship's bottom Use
Information
Red, White, Blue, Red brown 22.0 [degC] 54 (+-2) [volume %] 428 [g/L] 2 0.093 - 0.186 [L/m ] : WET 93 - 186 [micron] DRY 50 - 100 [micron]
5 C 3hrs. 6hrs. 6hrs. 8hrs.
o
(D.F.T. 50micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume FRP PRIMER -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 1000
NV
Apr.2006
No. 6180
1000
NOVA 1000, is Tar free modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, and salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type
Recommened Use
Tar free modified epoxy paint Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Information
Base : Hardener = 78 : 22 [by volume] Light grey, Cream Base = 25.5, Hardener = 24.9 [degC] 66 (+-2) [volume %] 378 [g/L] 2 0.189 - 0.379 [L/m ] : WET 189 - 378 [micron] DRY 125 - 250 [micron]
10 C 7hrs. 28hrs. 28hrs. 15days 10hrs.
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, CERABOND -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied as soon as possible after the minimum painting interval.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 1000 QD
NV
Apr.2006
No. 6180A
1000 QD
NOVA 1000 QD, is Tar free modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water and salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type
Tar free modified epoxy paint
Recommened Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 78 : 22 [by volume] Light Grey, Cream Base = 25.5, Hardener = 24.9 [degC] 67 (+-2) [volume %] 373 [g/L] 2 0.187 - 0.373 [L/m ] : WET 187 - 373 [micron] DRY 125 - 250 [micron]
-5 C 16hrs. 37hrs. 40hrs. 15day
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray Weather : Temperature : -5 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 4.Too much solvent results in reduced sag resistance and paint film property. 5.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000
NV
Mar.2007
No. 6181
2000
NOVA 2000, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Ballast water tank, Crude oil tank, Void space, Cofferdam, Use
Information
Mixing Ratio : Color : Flash Point : Specific Gravity : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Light Grey, Cream, Red brown Base = 37.0, Hardener = 21.5 [degC] 1.4 [g/mL] 80 (+-2) [volume %] 303 [g/L] 2 0.16 - 0.31 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
10 C 12hrs. 24hrs. 24hrs. 15days 5hrs. 8days
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life Dry to Launch Min
Condition of Application
Method of Application : Airless spray Weather : Temperature : 10 - 40 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 CH QD
NV
Mar.2006
No. 6181I
2000 CH QD
NOVA 2000 CH QD, is Tar free high solid modified epoxy paint, based on a combination ofmodified epoxy, special abrasive resistant agent. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and rust-prevention.It is suitable for protection of holds of steel ships.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Cargo hold Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] Light Grey, Red brown Base = 30.0, Hardener = 21.5 [degC] 80 (+-2) [volume %] 298 [g/L] 2 0.16 - 0.31 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
5 C 8hrs. 24hrs. 24hrs. 15days 5hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray Weather : Temperature : 0 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] NOVA THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 4.Too much solvent results in reduced sag resistance and paint film property. 5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases. 6.This product can not be applied to the grain as FDA-DRY CARGO
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
7.Wating time before the first cargo loading TEMP 5degC 10degC 20degC Days(DFT200micron) 25 16 10 Days(DFT400micron) 35 24 15 8.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 CH
NV
Mar.2006
No. 6181H
2000 CH
NOVA 2000 CH, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy, special abrasive resistant agent. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Cargo hold Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] Light Grey, Red brown Base = 30.0, Hardener = 21.5 [degC] 80 (+-2) [volume %] 303 [g/L] 2 0.16 - 0.31 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
10 C 12hrs. 24hrs. 24hrs. 15days 5hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.This product can not be applied to the grain as FDA-DRY CARGO 4.Wating time before the first cargo loading TEMP 10degC 20degC 30degC Days(DFT200micron) 20 12 7 Days(DFT400micron) 30 16 10 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 GF QD
NV
Mar.2006
No. 6181F
2000 GF QD
NOVA 2000 GF QD, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy and glass-flake. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Cargo hold Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] Light Grey, Red brown Base = 30.0, Hardener = 21.5 [degC] 80 (+-2) [volume %] 298 [g/L] 2 0.16 - 0.31 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
5 C 8hrs. 24hrs. 24hrs. 15days 5hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray Weather : Temperature : 0 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] NOVA THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 4.Too much solvent results in reduced sag resistance and paint film property. 5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases. 6.This product can not be applied to the grain as FDA-DRY CARGO. 7.Wating time before the first cargo loading
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TEMP 5degC 10degC 20degC Days(DFT200micron) 25 16 10 Days(DFT400micron) 35 24 15 8.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 GF
NV
Jan.2007
No. 6181G
2000 GF
NOVA 2000 GF, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy and glass-flake. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Cargo hold Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] Light Grey, Red Brown Base = 37.0, Hardener = 21.5 [degC] 80 (+-2) [volume %] 275 [g/L] 2 0.156 - 0.313 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
10 C 12hrs. 24hrs. 24hrs. 15days 5hrs.
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.This product can not be applied to the grain as FDA-DRY CARGO 4.Wating time before the first cargo loading TEMP 10degC 20degC 30degC Days(DFT200micron) 20 12 7 Days(DFT400micron) 30 16 10 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 QD
NV
Feb.2006
No. 6181A
2000 QD
NOVA 2000 QD, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam, Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Light Grey, Cream, Red brown Base = 37.0, Hardener = 21.5 [degC] 80 (+-2) [volume %] 298 [g/L] 2 0.16 - 0.31 [L/m ] : WET 156 - 313 [micron] DRY 125 - 250 [micron]
-5 C 17hrs. 44hrs. 44hrs. 15days
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray Weather : Temperature : 0 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] NOVA THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 4.Too much solvent results in reduced sag resistance and paint film property. 5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 W QD
NV
Mar.2007
No. 6181D
2000 W QD
NOVA 2000 W QD, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type
Tar free high solid modified epoxy paint
Recommened Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam, Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Light Grey, Cream, Red brown Base = 26, Hardener = 22.5 [degC] 76 (+-2) [volume %] 307 [g/L] 2 0.164 - 0.329 [L/m ] : WET 164 - 329 [micron] DRY 125 - 250 [micron]
-5 C 15hrs. 40hrs. 40hrs. 15days
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray Weather : Temperature : 0 - 15 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] NOVA THINNER, Thinning: 0 - 7 % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 4.Too much solvent results in reduced sag resistance and paint film property. 5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases. 6.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 5000
NV
Feb.2006
No. 6182
5000
NOVA 5000, solvent-free epoxy tank coating, is designed as a protective coating of ballast water tanks and cargo oil tanks. It has excellent water/sea-water resistance and has also superior crude oil resistance. NOVA 5000 is eco-friendly to the environment as it contains no solvent, no heavy metal. NOVA 5000 can be coated by conventional airless spray.
TECHNICAL DATA
Type
Solventfree epoxy coating
Recommened Ballast water tank, Crude oil tank, void space, cofferdam, hold, of ships. bridges, underground Use pipes, port facilities, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Light Grey Base = >250, Hardener = 155 [degC] 100 (+-2) [volume %] 122 [g/L] 2 0.3 [L/m ] : WET 300 [micron] DRY 300 [micron]
10 C 45hrs. 3days. 3days 14days 1.5hrs.
o
(D.F.T. 300micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray :
Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER ( for cleaning purpose), Thinning: - % by Volume WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER -
Packaging Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 6182A
5000 B
NOVA 5000 BARRIER, solvent-free epoxy putty, is designed as a repair protective coating of ballast water tanks and cargo oil tanks. It has excellent water/sea-water resistance and has also superior crude oil resistance, besides excellent adhesion even on simply treated or/and slightly dump surface. NOVA 5000 BARRIER is eco-friendly to the environment as it is solvent-free.
TECHNICAL DATA
Type
Solvent-free epoxy putty for repair
Recommened Ballast water tank, Void space, Cofferdam, Hold of ships, Bridges, Underground pipes, Port Use facilities, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 55 : 45 [by volume] Grey Base = >250, Hardener = 155 [degC] 100 (+-2) [volume %] 195 [g/L] 2 0.3 [L/m ] : WET 300 [micron] DRY 300 [micron]
5 C
o
(D.F.T. 300micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life Dry to Launch Min
Condition of Application
Method of Application : Brush; Roller; Spatula; Hand-glove Weather : Temperature : - degC, Humidity : Thinner Preceding Coats Subsequent Coats : : :
EPICON MARINE THINNER ( for cleaning only), Thinning: Not recommended. % by Volume -
Packaging Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NZ PRIMER S
NZ
Feb.2006
No. 1050
NZ PRIMER S, based on a combination of epoxy resin, rust-preventive pigments and hardener, is quick drying and gives adequate preliminary protection of blast-cleaned steel plates. It is compatible with almost any type of priming coat and highly resistant to heat, oil, water and solvents.
TECHNICAL DATA
Type
Non zinc type epoxy shop primer
Recommened As a shop primer for protection of blast- cleaned steel plates. Especially suitable for steel plates Use subject to prolonged weathering
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 73 : 27 [by volume] Red brown Base = 3.5, Hardener = 7.0 [degC] 23 [volume %] 655 [g/L] 2 0.091 [L/m ] : DRY 22 [micron]
5 C 8mins. 4hrs. 24hrs. 150days 72hrs.
o
(D.F.T. 22micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)9 - 10[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 80 - 120[cm/sec] EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Notes
Two pack product 1.Expected life for outdoor exposure [ under normal conditions ] : about 4 months 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000 S W
PM
Feb.2006
No. 6050A
3000S W
PERMAX No.3000 S W, based on a combination of epoxy resin with glass-flake and polyamide resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors. A film thickness of over 500 microns can be built in one application by airless spray.
TECHNICAL DATA
Type
Epoxy/polyamide glass flake mastic paint
Recommened Splash zone and underwater area of ship's outer shell and offshore structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 79 : 21 [by volume] Grey, Red brown, Black Base = 28.5, Hardener = 50 [degC] 92 (+-2) [volume %] 151 [g/L] 2 0.326 - 0.543 [L/m ] : WET 326 - 543 [micron] DRY 300 - 500 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
20 C
30 C
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 6.0[sec]
: : :
Tip No. : (GRACO)Zincgun(208-663) Paint Output Pressuer: 24.5 - 29.4[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume BANNOH 500, BANNOH 2000 BANNOH 500 N, VINYL AC-HB, etc.
Packaging Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000 S
PM
Feb.2006
No. 6050
3000S
PERMAX No.3000 S, based on a combination of epoxy resin with glass-flake and polyamide resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors. A film thickness of over 500 microns can be built in one application by airless spray.
TECHNICAL DATA
Type
Epoxy/polyamide glass flake mastic paint
Recommened Splash zone and underwater area of ship's outer shell and offshore structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 79 : 21 [by volume] Grey, Red brown, Black Base = 28.5, Hardener = 50 [degC] 92 (+-2) [volume %] 153 [g/L] 2 0.326 - 0.543 [L/m ] : WET 326 - 543 [micron] DRY 300 - 500 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 6.0[sec]
: : :
Tip No. : (GRACO)SILVERGUN(208-663) Paint Output Pressuer: 24.5 29.4[MPa] Spray Speed : 60 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume BANNOH 500, BANNOH 2000 BANNOH 500 N, VINYL AC-HB, etc.
Packaging Notes
Two pack product 1.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000MU
PM
Dec.2006
No. 6057
3000MU
PERMAX No.3000MU, based on a combination of epoxy resin with glass-flake and polyamine resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors.
TECHNICAL DATA
Type
Epoxy/polyamine glass flake mastic paint
Recommened Splash zone and underwater area of ship's outer shell and offshore structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 82 : 18 [by volume] Light Grey, Red brown Base = 32, Hardener = 24.5 [degC] 80 (+-2) [volume %] 239 [g/L] 2 0.25 - 0.375 [L/m ] : WET 250 - 375 [micron] DRY 200 - 300 [micron]
5 C
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
10 C
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray :
: : :
Tip No. : GRACO BallTip No205-723 Zincgun(208-663) Paint Output Pressuer: 14.7 - 19.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume CERABOND BANNOH 500, BANNOH 500 N, EPICON MARINE HB, etc.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000MU W
PM
Dec.2006
No. 6059
3000MU W
PERMAX No.3000MU W, based on a combination of epoxy resin with glass-flake and polyamine resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors.
TECHNICAL DATA
Type
Epoxy/polyamine glass flake mastic paint
Recommened Splash zone and underwater area of ship's outer shell and offshore structures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 82 : 18 [by volume] Light Grey, Red brown Base = 32, Hardener = 26 [degC] 80 (+-2) [volume %] 225 [g/L] 2 0.25 - 0.375 [L/m ] : WET 250 - 375 [micron] DRY 200 - 300 [micron]
5 C 10hrs. 28hrs. 28hrs. 10days 4hrs.
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray :
Tip No.
: : :
: (GRACO)BallTip No205-723 Zincgun(208-663) Paint Output Pressuer: 14.7 - 19.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume CERABOND BANNOH 500, BANNOH 500 N, EPICON MARINE HB, etc.
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
POLIBI T-1
PB
Feb.2006
No. 3040
T-1
POLIBI T-1 is a vinyl chloride resin based paint, providing excellent adhesion property, durability, weathering resistance and gloss retention. It is quick drying and easy to apply. Recommended as a finishing coat on the inside and outside of superstructures.
TECHNICAL DATA
Type
Vinyl finish paint
Recommened Finish coat of vinyl system on the ship's inside and outside superstructures area and other steel Use structures.
Information
White 7.3 [degC] 28 [volume %] 605 [g/L] 2 0.072 - 0.108 [L/m ] : WET 72 - 108 [micron] DRY 20 - 30 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)30 - 45[sec]
: : :
Tip No. : (GRACO)717,719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec] VINYL THINNER, Thinning: 6 - 12 % by Volume VINYL RED LEAD PRIMER, VINYL RED LEAD PRIMER HB, VINYL AC -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX
RX
FC
FINISH
Feb.2006
No. 4400
RAVAX FINISH, based on a chlorinated rubber vehicle, physically dries by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention. It is also highly resistant to the influence of salt water, oil and chalking. Although standard dry film thickness is 35 microns per coat, it is possible to obtain a maximum of 50 microns dry film thickness per coat.
TECHNICAL DATA
Type
Chlorinated rubber finish paint
Recommened As a finishing coat on interior and exterior of superstructures Use
Information
White, As specified 25.5 [degC] 42 (+-2) [volume %] 484 [g/L] 2 0.072 - 0.12 [L/m ] : WET 72 - 120 [micron] DRY 30 - 50 [micron]
5 C 1hr. 6hrs. 12hrs. o
(D.F.T. 35micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)100[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume RAVAX PRIMER, RAVAX RED LEAD PRIMER, etc. -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX
RX
PRIMER
Feb.2006
No. 4100
RAVAX PRIMER is an effective anti-rust primer based on chlorinated rubber and drying by evaporation of the solvents. It has excellent rust-preventing and adhesion properties, weathering and oil resistance and other physical properties.
TECHNICAL DATA
Type
Chlorinated rubber anti-rust primer
Recommened As an anti-rust primer on the superstructure of ships Use
Information
Red brown, White, Light gray 25.5 [degC] 43 (+-2) [volume %] 495 [g/L] 2 0.082 - 0.105 [L/m ] : WET 82 - 105 [micron] DRY 35 - 45 [micron]
5 C 1hr. 8hrs. 10hrs. o
(D.F.T. 40micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GRACO)721,719 Paint Output Pressuer: 11.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, WELBOND, CERABOND, EPICON ZINC RICH PRIMER, RAVAX FINISH, RAVAX DECK, etc.
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX AC HB
RX
Feb.2006
No. 4001
AC HB
RAVAX AC HB is a chlorinated rubber paint giving a high-build quick drying, effective protection against corrosion. It affords good adhesion between the films as well as to shop primers and subsequent coats. It also possesses sea water resistance and shows good adhesion to subsequent coats even after prolonged weathering.
TECHNICAL DATA
Type
Chlorinated rubber anti-corrosive paint, high-build
Recommened Steel ship's hull and other steel structures Use
Information
SR (Pink silver), S (Silver) 27.0 [degC] 42 (+-2) [volume %] 489 [g/L] 2 0.095 - 0.179 [L/m ] : WET 95 - 179 [micron] DRY 40 - 75 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)140[sec]
: : :
Tip No. : (GRACO)721,723 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, CERABOND, etc. RAVAX AF, RAVAX FINISH, TFA-10.20.30, etc.
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX AF
RX
Mar.2006
No. 4010
AF
RAVAX AF is a special synthetic resin based anti-fouling paint with a high content of antifoulant, providing extended effective protection against fouling, results in fuel saving and elimination of lost time due to reduction in speed resulting from fouling. It has excellent adhesion to RAVAX AC.
TECHNICAL DATA
Type
Special synthetic resin anti-fouling paint
Recommened Anti-fouling finish of chlorinated rubber system on steel ship's bottom areas Use
Information
Dark red brown 24.3 [degC] 50 (+-2) [volume %] 421 [g/L] 2 0.07 - 0.09 [L/m ] : WET 70 - 90 [micron] DRY 35 - 45 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume RAVAX AC, RAVAX AC HB, RAVAX AC S-HB, SILVAX SQ, etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD
RWN
Feb.2006
No. 2130
QD
ROSWAN QD, a white coloured alkyd resin based rust-preventing primer, has highly rust-preventing property. As it is white colour, it is especially recommended for use as a primer for white or light-colour finishes.
TECHNICAL DATA
Type
Alkyd resin white primer.
Recommened As a rust-preventing primer for inside and outside of the superstructure and other steel Use structures
Information
White 43.0 [degC] 51 (+-2) [volume %] 390 [g/L] 2 0.059 - 0.078 [L/m ] : WET 59 - 78 [micron] DRY 30 - 40 [micron]
5 C 4hrs. 18hrs. 30hrs. 120days
o
(D.F.T. 35micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)110[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 110[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, LZI PRIMER, etc. EVMARINE, Alkyd resin based paints
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD HB
RWN
Oct.2006
No. 2131
QD HB
ROSWAN QD HB, a white colored alkyd resin based rust-preventing primer has highly effective rust-preventing property. Being white, it is especially recommended for use as a primer for white and light-colored finishes.
TECHNICAL DATA
Type
Special alkyd resin primer, High-build
Recommened As a rust-preventing primer for inside of superstructure, deck, hold, and other steel structures Use
Information
White 36.0 [degC] 51 (+-2) [volume %] 393 [g/L] 2 0.059 - 0.137 [L/m ] : WET 59 - 137 [micron] DRY 30 - 70 [micron]
5 C 6hrs. 24hrs. 48hrs. 120days
o
(D.F.T. 70micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush*, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pas
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, LZI PRIMER, etc. EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging Notes
One pack product 1.* Sufficient thickness is difficult to obtain by brush. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD ZR HB
RWN
Feb.2006
No. 2134
QD ZR HB
ROSWAN QD ZR HB, a white coloured alkari-resistant synthetic resin based rust-preventing primer has highly effective rust-preventing property. Being white, it is especially recommended for use as a primer for white and light-coloured finishes.
TECHNICAL DATA
Type
Special synthetic resin primer,High-build
Recommened As the 1st coat of primer for inside of superstructure and other steel structures, when a Use conventional paint systen is specified on zinc shop primer.
Information
White 36.0 [degC] 51 (+-2) [volume %] 393 [g/L] 2 0.058 - 0.137 [L/m ] : WET 59 - 137 [micron] DRY 30 - 70 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush*, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pas
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, CERABOND, WELBOND, NZ PRIMER, etc. EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging Notes
One pack product 1.* Sufficient thickness is difficult to obtain by brush. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD ZS HB
RWN
Feb.2006
No. 2136
QD ZS HB
ROSWAN QD ZS HB, a white coloured alkari-resistant synthetic resin based rust-preventing primer, has highly effective rust-preventing property. Being white colour, it is especially recommended for use as a primer for white and light-coloured finishes.
TECHNICAL DATA
Type
Special synthetic resin primer
Recommened As the 1st coat of primer for inside of superstructure and other steel structures, when a Use conventional paint system is specified on zinc shop primer.
Information
White 31.0 [degC] 44 (+-2) [volume %] 461 [g/L] 2 0.067 - 0.157 [L/m ] : WET 67 - 157 [micron] DRY 30 - 70 [micron]
5 C 6hrs. 24hrs. 48hrs. 120days
o
(D.F.T. 70micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GARCO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, EPICON ZINC RICH PRIMER B-2, CERABOND 2000, NZ PRIMER, etc. EVAMARINE, ROSWAN QD*, ROSWAN QD HB, Alkyd resin based paints
Packaging Notes
One pack product 1.* In case of applying alkyd resin finish coat on ROSWAN QD ZS HB at outdoor exposed area or high humidity area , ROSWAN QD to be applied as a binder coat. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 8250
RUST INHIBITIVE OIL "CK", based on special petroleum resin and mineral spirit, is a temporary protective primer for fuel oil tanks.
TECHNICAL DATA
Type
Recommened Use
Petroleum resin
Information
Clear 42.5 [degC] 49 [volume %] 386 [g/L] 2 0.043 [L/m ] : WET 41 [micron] DRY 20 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
10 C 30mins. 2hrs. -
20 C 15mins. 1hr. -
30 C 5mins. 30mins. -
1hr. 4hrs. -
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Packaging Notes
One pack product 1.The ingredients of this product will be dissolved by the fuel oil but they do not affect the quality of the fuel oil at all. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Sep.2006
No. 2110
RUST INHIBITIVE PRIMER Z is an alkyd based primer. It is a highly effective rust-preventing primer which possesses excellent adhesion properties and flexibility.
TECHNICAL DATA
Type
Alkyd resin primer
Recommened As a rust-preventing primer on inside and outside of superstructures, deck, hold, and other steel Use structures
Information
Red brown 43.0 [degC] 52 (+-2) [volume %] 383 [g/L] 2 0.058 - 0.077 [L/m ] : WET 58 - 77 [micron] DRY 30 - 40 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
: : :
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec] MARINE THINNER, Thinning: 0 - 5 % by Volume EVABOND, NZ PRIMER, etc. EVAMARINE, Alkyd resin based paints
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER
SFT
Mar.2006
No. 5917N
SEA FRONTIER , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Light red, Pink, 25.0 [degC] 41 (+-2) [volume %] 528 [g/L] 2 0.18 - 0.37 [L/m ] : WET 183 - 366 [micron] DRY 75 - 150 [micron]
o
Blue
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER
SFT
Mar.2006
No. 5922N
SEA FRONTIER F , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Light red 25.0 [degC] 40 (+-2) [volume %] 522 [g/L] 2 0.187 - 0.371 [L/m ] : WET 373 [micron] DRY 150 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER
SFT
Mar.2006
No. 5919N
SEA FRONTIER H , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Pink, Blue, Black 25.0 [degC] 41 (+-2) [volume %] 518 [g/L] 2 0.18 - 0.37 [L/m ] : WET 183 - 366 [micron] DRY 75 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER
SFT
Mar.2006
No. 5921N
SEA FRONTIER S, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Light red, Pink, 25.0 [degC] 41 (+-2) [volume %] 528 [g/L] 2 0.18 - 0.37 [L/m ] : WET 183 - 366 [micron] DRY 75 - 150 [micron]
o
Black
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER ME
SFT
Mar.2006
No. 5917M
ME
SEA FRONTIER ME , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Light red 24.5 [degC] 45 (+-2) [volume %] 474 [g/L] 2 0.11 - 0.33 [L/m ] : WET 111 - 333 [micron] DRY 50 - 150 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5909
1000
SEA GRANDPRIX 1000 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Red, Dark red, Light red, 23.2 [degC] 44 (+-2) [volume %] 504 [g/L] 2 0.17 - 0.34 [L/m ] : WET 170 - 340 [micron] DRY 75 - 150 [micron]
5 C
o
Purple
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.Below 10 degC, extra solvent maybe required to obtain application viscosity. 3.But too much solvent results in reduced sag resistance and paint film property. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5911
2000
SEA GRANDPRIX 2000 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Red, Light red, Brown, 23.2 [degC] 44 (+-2) [volume %] 494 [g/L] 2 0.17 - 0.34 [L/m ] : WET 170 - 340 [micron] DRY 75 - 150 [micron]
o
Purple
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 AC, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5901
300
SEA GRANDPRIX 300,is used for fouling control on the flat bottom, is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's flat bottom for world wide service with extended dry-docking Use interval.
Information
Red, Light red, Purple 25.0 [degC] 47 (+-2) [volume %] 484 [g/L] 2 0.16 - 0.32 [L/m ] : WET 160 - 319 [micron] DRY 75 - 150 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, HIPER AC, RAVAX AC HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2007
No. 5902
330
SEA GRANDPRIX 330 is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique fusion technology during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Brown, Light brown 26.0 [degC] 62 (+-2) [volume %] 371 [g/L] 2 0.12 - 0.24 [L/m ] : WET 121 - 242 [micron] DRY 75 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5905
500
SEA GRANDPRIX 500 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Red, Light red, Purple 25.0 [degC] 46 (+-2) [volume %] 481 [g/L] 2 0.16 - 0.33 [L/m ] : WET 163 - 326 [micron] DRY 75 - 150 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GARCO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.Below 10 degC, extra solvent maybe required to obtain application viscosity. 3.But too much solvent results in reduced sag resistance and paint film property. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5905M
500 M
SEA GRANDPRIX 500 M is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Red, Light red, Purple 25.0 [degC] 46 (+-2) [volume %] 495 [g/L] 2 0.16 - 0.33 [L/m ] : WET 163 - 326 [micron] DRY 75 - 150 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5912
800
SEA GRANDPRIX 800 is a tin free self polishing antifouling paint based on the specific polymer with hydrolysis activity. Excellent antifouling effect is derived from the active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for coastal ships. Use
Information
Red, Light red 23.2 [degC] 44 (+-2) [volume %] 513 [g/L] 2 0.11 - 0.34 [L/m ] : WET 113 - 340 [micron] DRY 50 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 R, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF MK II
SGP
Dec.2006
No. 5830
CF MK II
SEA GRANDPRIX CF MK II is a tin and copper free self polishing anti-fouling paint based on a unique hydrolysis polymer. In service, SEA GRANDPRIX CF MK II's unique polymer presents a very thin hydrolysed active layer on the paint film surface ensuring an efficient and controlled biocide release mechanism. In our view this is the most efficient biocide release mechanism currently available. This efficient biocide release mechanism also ensures an extremely low hull surface roughness. The absence of tin, copper and other heavy metals in SEA GRANDPRIX CF MK II means that it remains colour-fast without fading or staining for the duration of the service life . IMO Anti-fouling System Convention compliant (AFS/CONF/26)
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red, Purple 25.0 [degC] 50 2 [volume %] 437 [g/L] 2 0.15 - 0.32 [L/m ] : WET 150 - 320 [micron] DRY 75 - 160 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB, -
Packaging Notes
One pack product 1.The information contained in this technical data sheets in based on laboratory testing and practical in service experience. Note 1: Please refer to the above painting intervals and dry to launch times, for below 320 total DFT.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Note 2: When applying over 320 total DFT, or applying 3 coats or more, CMP recommend that 1 (one) day interval between the application of A/F and A/F and 24 hours minimum dry to launch. Note 3: In case of application below 5C. 2.(below 0degC) Surface Hard Interval Interval dry to Launch Dry Dry Min Max Min 0degC 4hrs 16hr 16hr 36hr -5degC 6hrs 22hr 22hr 48hr
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF MK II L
SGP
Dec.2006
No. 5831
CF MK II L
SEA GRANDPRIX CF MK II L is a tin and copper free self polishing anti-fouling paint based on a unique hydrolysis polymer. In service, SEA GRANDPRIX CF MK II L's unique polymer presents a very thin hydrolysed active layer on the paint film surface ensuring an efficient and controlled biocide release mechanism. In our view this is the most efficient biocide release mechanism currently available. This efficient biocide release mechanism also ensures an extremely low hull surface roughness. The absence of tin, copper and other heavy metals in SEA GRANDPRIX CF MK II L means that it remains colour-fast without fading or staining for the duration of the service life .
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red, Purple 24.5 [degC] 50 2 [volume %] 435 [g/L] 2 0.15 - 0.32 [L/m ] : WET 150 - 320 [micron] DRY 75 - 160 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB, -
Packaging Notes
One pack product 1.The information contained in this technical data sheets in based on laboratory testing and practical in service experience. Note 1: Please refer to the above painting intervals and dry to launch times, for below 320 total DFT. Note 2: When applying over 320 total DFT, or applying 3 coats or more, CMP recommend
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
that 1 (one) day interval between the application of A/F and A/F and 24 hours minimum dry to launch. Note 3: In case of application below 5C. 2.(below 0degC) Surface Hard Interval Interval dry to Launch Dry Dry Min Max Min 0degC 4hrs 16hr 16hr 36hr -5degC 6hrs 22hr 22hr 48hr
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5921
CF SP
SEA GRANDPRIX CF SUPER, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Light red, Pink 25.0 [degC] 44 (+-2) [volume %] 488 [g/L] 2 0.17 - 0.341 [L/m ] : WET 170 - 341 [micron] DRY 75 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Nov.2006
No. 5917P
CF SP NFD
SEA GRANDPRIX CF SUPER NFD, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for an None Final Dock system of new buildings in the heavy fouled area . Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red 25.0 [degC] 42 2 [volume %] 509 [g/L] 2 0.071 - 0.238 [L/m ] : WET 71 - 238 [micron] DRY 30 - 100 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)617 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SEA GRANDPRIX CF-10, SEA GRANDPRIX CF-10 L, SEA GRANDPRIX 1000, SEA GRANDPRIX 500 -
Packaging Notes
One pack product 1.This is a temporary anti-fouling paint for an out fitting period of New buildings at the heavy fouled area such as Tokyo bay, Ise bay and Oosaka bay etc. 2. Any other subsequent coats can not be compatible on this paint due to special paint for non final dock system
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Sep.2006
No. 5917K
CF-10
SEA GRANDPRIX CF-10 , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red, Purple 25.0 [degC] 44 (+-2) [volume %] 487 [g/L] 2 0.17 - 0.364 [L/m ] : WET 170 - 364 [micron] DRY 75 - 160 [micron]
-5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.Below 10 degC, extra solvent maybe required to obtain application viscosity. 3.But too much solvent results in reduced sag resistance and paint film property. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Sep.2006
No. 5917L
CF-10 L
SEA GRANDPRIX CF-10 L , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red, Purple 24.5 [degC] 44 (+-2) [volume %] 484 [g/L] 2 0.17 - 0.364 [L/m ] : WET 170 - 364 [micron] DRY 75 - 160 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5928
CF-10 L M
SEA GRANDPRIX CF-10 L M , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red 24.5 [degC] 43 (+-2) [volume %] 491 [g/L] 2 0.174 - 0.372 [L/m ] : WET 174 - 372 [micron] DRY 75 - 160 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5927
CF-10 M
SEA GRANDPRIX CF-10 M , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin and copper free self polishing antifouling
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval
Information
Red, Light red 25.0 [degC] 43 (+-2) [volume %] 494 [g/L] 2 0.174 - 0.372 [L/m ] : WET 174 - 372 [micron] DRY 75 - 160 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Mar.2006
No. 5919
CF20
SEA GRANDPRIX CF-20 , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type
Tin free self polishing antifouling without cuprous oxide
Recommened On the ship bottom for coastal steel ships and aluminum boats Use
Information
Red, Pink, Blue 25.0 [degC] 41 (+-2) [volume %] 518 [g/L] 2 0.18 - 0.37 [L/m ] : WET 183 - 366 [micron] DRY 75 - 150 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, etc. -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2007
No. 5923
FRP
SEA GRANDPRIX FRP is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing execllent antifouling performance.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint for FRP boat and plesure boat. Use
Information
Light red 23.2 [degC] 42 (+-2) [volume %] 494 [g/L] 2 0.119 - 0.238 [L/m ] : WET 119 - 238 [micron] DRY 50 - 100 [micron]
5 C 3hrs. 12hrs. 12hrs. 24hrs.
o
(D.F.T. 50micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
30 C
Condition of Application
Method of Application : Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pas
: : :
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume FRP PRIMER -
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 015
SJ
Jan.2006
No. 9102
015
SEAJET015based on special acrylic resin, provides excellent adhesion to FRP surfaces and subsequent antifouling paint. It is quick drying and forms a tough yet flexible film which is highly resistant to weather and sea water.
TECHNICAL DATA
Type
Acrylic resin primer
Recommened As aprimer and binder coat for FRP boats' bottom Use
Information
Silver 23.0 [degC] 35 (+-2) [volume %] 560 [g/L] 2 0.11 [L/m ] : WET 114 [micron] DRY 40 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 40[sec] Thinner Preceding Coats Subsequent Coats : : :
Tip No. : (IWATA)W-77-2S,etc Spray Speed : 80 - 100[cm/sec] SEAJET THINNER A, Thinning: 15 - 25 % by Volume SEAJET033, SEAJET034, SEAJET035
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 033
SJ033
Feb.2006
No. 9110
SEAJET033 is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling performance.
TECHNICAL DATA
Type
Tin free antifouling paint
Recommened Antifouling paint on FRP ship's bottom Use
Information
Red, Blue, Black, 30.0 [degC] 456 [g/L] 2 0.107 [L/m ] : WET 98 [micron] DRY 50 [micron]
Shark white
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Air spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. Thinner : SEAJET THINNER A, Preceding Coats Subsequent Coats : :
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 132
SJ
Feb.2006
No. 9121
132
SEAJET 132 is a polyurethane based high gloss finish coat. It has excellent gloss retention and durability and good adhesion property. It is suitable for top coat of pleasure boat and yacht.
TECHNICAL DATA
Type
Polyurethane paint
Recommened Top coat for pleasure boat and yacht. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 5 : 1 [by volume] White, Blue, Red , Yellow, Green, Orange Base = 25.3, Hardener = 29.5 [degC] 45 (+-2) [volume %] 462 [g/L] 2 0.077 - 0.11 [L/m ] : WET 77 - 110 [micron] DRY 35 - 50 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Air spray Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 15 - 20[sec] Thinner Preceding Coats Subsequent Coats : : :
Tip No. : (IWATA Spraygun)W-71-3S Spray Speed : 80 - 100[cm/sec] SEAJET B THINNER, Thinning: 15 - 30 % by Volume SEAJET111 -
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 137
SJ137
Feb.2006
No. 9124
SEAJET137 is a finishing coat based on acrylic resin and drying by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention.
TECHNICAL DATA
Type
Acrylic finish paint
Recommened Top coat for pleasure boat and yacht. Use
Information
Color : Flash Point : Specific Gravity : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
White, As specified, , 25.7 [degC] 1.18 [g/mL] [volume %] 598 [g/L] 2 0.087 - 0.145 [L/m ] : WET 100 - 143 [micron] DRY 35 - 50 [micron]
o
(D.F.T. 35micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max
Condition of Application
Method of Application : Airless spray, Air spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)15 - 20[sec] Thinner Preceding Coats Subsequent Coats : : :
Packaging Notes
One pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 145W
SJ
Feb.2006
No. 9130
145W
SEAJET 145W is epoxy resin based putty with the performance of super light weight, good adhesion, good filling and good fairing.
TECHNICAL DATA
Type
Epoxy resin based putty
Recommened Filling, fairing of wooden, steel, aluminium or FRP substrates. Use
Information
Base : Hardener = 67 : 33 [by volume] Pink Base = -, Hardener = - [degC] 0 [g/L] 2 2 [L/m ] : DRY 2000 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Spatula; Trowel Weather : Temperature : 5 - 25 degC, Humidity : Maximum 85 %R.H. Thinner : Preceding Coats : SEAJET010,SEAJET020 Subsequent Coats : SEAJET020,etc
Packaging Notes
Two pack product VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR PRIMER
SN
Oct.2006
No. 8032
HR PR
SILICON HR PRIMER is a silicon resin primer based on silicon resin with curing accelerator. It has the following characteristics. 1. Excellent heat resistance (up to 700 degC) 2. Excellent weathering resistance 3. Excellent application workability 4. Excellent adhesion property
TECHNICAL DATA
Type
Silicone resin heat resisting primer
Recommened As undercoat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Curing Accelerator = 100 : 1.53 [by volume] White Base = 19.3, Curing Accelerator = 38.3 [degC] 38 (+-2) [volume %] 542 [g/L] 2 0.066 [L/m ] : WET 66 [micron] DRY 25 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
: : :
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec] SILICON THINNER, Thinning: 5 - 10 % by Volume SILICON HR SILVER HG, SILICON HR
Packaging Notes
Two pack product 1.Paint film should be baked for 2 hours at 200 degC to complete curing. 2.Total paint film thickness of painting specification should be less than 150 micron. 3.Surface preparation: In case of direct application to the steel surface, ISO Sa2.5. In case of application on shop primer coated surface, ISO St3 is required. The surface to be painted must be clean, free from rust, oil grease or other foreign matter using power wash, detergent, or solvent wipe. 4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1. 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR SILVER HG
SN
Feb.2006
No. 8035
HR SIL HG
SILICON HR SILVER HG, is a silicone heat resisting paint based on silicone resin pigmented and aluminium pigment. It has the following advantages; 1. Excellent heat resistance (up to 400 degC) 2. Excellent weather resistance 3. Excellent application workability 4. Excellent adhesion property
TECHNICAL DATA
Type
Silicone resin heat resisting aluminium paint
Recommened As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Curing Accelerator = 100 : 1.21 [by volume] SILVER Base = 19.5, Curing Accelerator = 38.3 [degC] 34 (+-2) [volume %] 586 [g/L] 2 0.045 - 0.059 [L/m ] : WET 45 - 59 [micron] DRY 15 - 20 [micron]
5 C 1hr. 7hrs. 20hrs. 32hrs.
o
(D.F.T. 15micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)10 - 20[sec]
: : :
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec] SILICON THINNER, Thinning: 5 - 10 % by Volume SILICON HR PRIMER -
Packaging Notes
Two pack product 1. Paint film should be baked for 2 hours at 200 degC to complete curing. 2. Total paint film thickness of painting specification should be below 150 micron. 3. Surface preparation : In case of direct application to the steel surface, ISO Sa 2.5. In case of application on shop primer coated surface, ISO St 3 is required. The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe. 4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR SILVER
SN
Feb.2006
No. 8034
HR SIL
SILICON HR SILVER, is a silicone heat resisting finish on inorganic zinc primer based on silicone resin pigmented with aluminium pigment. It has the following advantages; 1. Excellent heat resistance (up to 700 degC) 2. Excellent weather resistance 3. Excellent application workability 4. Excellent compatibility with inorganic zinc primer
TECHNICAL DATA
Type
Silicone resin heat resisting aluminium paint
Recommened As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Curing Accelerator = 100 : 1.21 [by volume] Silver Base = 22.3, Curing Accelerator = 38.3 [degC] 25 (+-2) [volume %] 650 [g/L] 2 0.06 - 0.08 [L/m ] : WET 60 - 80 [micron] DRY 15 - 20 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)10 - 20[sec]
: : :
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec] SILICON THINNER, Thinning: 5 - 10 % by Volume SILICON HR PRIMER -
Packaging Notes
Two pack product 1. Paint film should be baked for 2 hours at 200 degC to complete curing. 2. Surface preparation : The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe. 3. Total thickness of specification should be less than 150 micron. 4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1. 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR
SN
Feb.2006
No. 8033
HR
SILICON HR, is a silicone heat resisting paint based on silicone resin pigmented with heat resisting pigment. It has the following advantages; 1. Excellent heat resistance (up to 700 degC) 2. Excellent weather resistance 3. Excellent application workability 4. Excellent adhesion property
TECHNICAL DATA
Type
Silicone resin heat resisting paint
Recommened As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Curing Accelerator = 100 : 1.42 [by volume] White, Black, Red brown, Light colours Base = 20, Curing Accelerator = 38.3 [degC] 38 (+-2) [volume %] 546 [g/L] 2 0.04 - 0.066 [L/m ] : WET 40 - 66 [micron] DRY 15 - 25 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
: : :
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec] SILICON THINNER, Thinning: 5 - 10 % by Volume SILICON HR PRIMER -
Packaging Notes
Two pack product 1. Paint film should be baked for 2 hours at 200 degC to complete curing. 2. Total paint film thickness of painting specification should be less than 150 micron. 3. Surface preparation : The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe. 4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1. 5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Feb.2006
No. 8000
500
SILVA SPAR No.500 is an alkyd resin based aluminium paint with outstanding heat resisting and rust-preventing properties. It presents a beautiful appearance. SILVA SPAR No.500 successfully withstands temperatures of up to 150C.
TECHNICAL DATA
Type
Alkyd/Aluminium heat resisting paint
Recommened As a protective coating on steel surfaces reaching high temperatures Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Varnish : Aluminium paste = 89 : 11 [by volume] Metallic Silver Varnish = 35.0, Aluminium paste = 43.3 [degC] 44 (+-2) [volume %] 451 [g/L] 2 0.034 - 0.056 [L/m ] : WET 34 - 56 [micron] DRY 15 - 25 [micron]
0 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)40[sec]
: : :
Tip No. : (GRACO)713 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 100 - 120[cm/sec] MARINE THINNER, Thinning: - % by Volume LZI PRIMER HB, RED LEAD PRIMER QD, Alkyd resin based primer -
Packaging Notes
Two pack product 1.Applying within the recommended film thickness range to avoid the wrinkling. 2.After adding the aluminium paste to the base component, applying early to keep the brightness. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILVAX SQ-K
SX
Mar.2006
No. 3007
SQ K
SILVAX SQ-K, modified vinyl paint, forms a practically impervious barrier against water and provides an excellent key for subsequent anti-fouling paints.
TECHNICAL DATA
Type
Modified vinyl anti-corrosive paint.
Recommened Anti-corrosive for steel ships bottom, Binder-coat for anti-fouling paint Use
Information
S(Silver), SR(Pink silver) 18.8 [degC] 30 [volume %] 611 [g/L] 2 0.13 - 0.27 [L/m ] : WET 133 - 266 [micron] DRY 40 - 80 [micron]
5 C 1.5hrs. 12hrs. 12hrs. 15hrs. 7days
o
(D.F.T. 80micron) Drying Time Surface Dry Hard Dry Painting Interval Min (AC) (AF) Max (AC) (AF)
Condition of Application
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] VINYL THINNER, Thinning: 0 - 10 % by Volume BISCON AC-QL, BISCON AC-AL, etc. SEA GRANDPRIX 100,200 series
Packaging Notes
One pack product 1.Before application of subsequent coat, clean the surface by fresh water washing or other means if surface is contaminated by chalking or impurities. 2. VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILVAX SQ-M
SX
Mar.2006
No. 3008
SQ M
SILVAX SQ-M, modified vinyl paint, forms a practically impervious barrier against water and provides an excellent key for subsequent anti-fouling paints.
TECHNICAL DATA
Type
Modified vinyl anti-corrosive paint.
Recommened Anti-corrosive for steel ships bottom, Binder-coat for anti-fouling paint Use
Information
S(Silver), R(Red silver brown) 18.8 [degC] 36 [volume %] 571 [g/L] 2 0.138 - 0.259 [L/m ] : WET 110 - 207 [micron] DRY 40 - 75 [micron]
5 C 1hr. 8hrs. 8hrs. 14hrs. 7days
o
(D.F.T. 75micron) Drying Time Surface Dry Hard Dry Painting Interval Min (AC) (AF) Max (AC) (AF)
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
: : :
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] VINYL THINNER, Thinning: 0 - 10 % by Volume BISCON AC, BISCON AC-HB, BISCON AC-QL, BISCON AC-QL HB, SILVAX SQ-M, BANNOH 500 etc MARINE STAR 10,20 series, TFA-10 series, SILVAX SQ-M
Packaging Notes
One pack product 1. Before application of subsequent coat, clean the surface by fresh water washing or other means if surface is contaminated by chalking or impurities. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TFA FLAT
TFA
Mar.2006
No. 5873
TFA FLAT S is a tin free antifouling paint with self polishing action. The product is used for fouling control on the flat bottom.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ships' flat bottom for world wide service with extended drydocking Use interval.
Information
Red, Pink 23.0 [degC] 52 (+-2) [volume %] 457 [g/L] 2 0.095 - 0.19 [L/m ] : WET 95 - 190 [micron] DRY 50 - 100 [micron]
5 C
o
() Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 633(733) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ, VINYL AC-HB, RAVAX AC-P, RAVAX AC, RAVAX AC-HB, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TFA-10
TFA
Mar.2006
No. 5865G
10
TFA-10 is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type
Tin free self polishing antifouling paint
Recommened Antifouling paint on steel ship's bottom for world wide service with extended dry-docking Use interval.
Information
Dark red, Light red 23.0 [degC] 55 (+-2) [volume %] 476 [g/L] 2 0.18 - 0.27 [L/m ] : WET 182 - 273 [micron] DRY 100 - 150 [micron]
-5 C 6hrs. 22hrs. 22hrs. 48hrs.
o
(D.F.T. 100micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Dry to Launch Min
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
: : :
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec] RAVAX THINNER, Thinning: 0 - 5 % by Volume SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC, -
Packaging Notes
One pack product 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling. 2.Below 10 degC, extra solvent maybe required to obtain application viscosity. 3.But too much solvent results in reduced sag resistance and paint film property. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD PU
UG
Feb.2006
No. 6165
PU
UMEGUARD PU is based on epoxy polyurethane resin. It gives excellent physical properties such as adhesion, flexibility, toughness and abrasion resistance, etc. and chemical resistance to water and sea water. It has good adhesion to the existing paint surface. UMEGUARD PU is suitable for repair of ships by simply surface preparation such as disc sanding or chipping, and for newbuilding ships by simply surface preparation such as brooming or hand brushing.
TECHNICAL DATA
Type
Epoxy urethane resin paint, high build
Recommened Deck, Hatch cover, etc. Use
Information
Base : Hardener = 88 : 12 [by volume] White, Grey, White, Green Base = 6.0, Hardener = 2.0 [degC] 445 [g/L] 2 0.16 - 0.32 [L/m ] : WET 160 - 320 [micron] DRY 100 - 200 [micron]
5 C 50mins. 22hrs. 22hrs. 3 5hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.2 - 1.8Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON QL THINNER, Thinning: 0 - 10 % by Volume WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, PU-TU, etc. -
UMEGUARD
Packaging Notes
Two pack product 1.The surface must be thoroughly cleaned by thinner wiping of fresh water washing to remove salt, dirt, oil, grease, chalking and impurities. 2.Minimum coating intervals on the existing film are as follows. (Alkyd paint : more than 6 months, Chlorinated rubber paint : more than 12 months, Epoxy paint : more than 2 days)
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD PU-TU
UG
Feb.2006
No. 6164
PU-TU
UMEGUARD PU-TU is based on epoxy polyurethane resin. It gives excellent physical properties such as adhesion, flexibility, toughness and abrasion resistance, etc. and chemical resistance to water and sea water. It has good adhesion to the existing paint surface. UMEGUARD PU-TU is suitable for repair of ships by simply surface preparation such as disc sanding or chipping, and for newbuilding ships by simply surface preparation such as brooming or hand brushing.
TECHNICAL DATA
Type
Epoxy urethane resin paint, high build
Recommened Deck, Hatch cover, etc. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 88 : 12 [by volume] Brown Base = 6.0, Hardener = 2.0 [degC] 69 (+-2) [volume %] 303 [g/L] 2 0.145 - 0.29 [L/m ] : WET 145 - 290 [micron] DRY 100 - 200 [micron]
5 C 50min. 22hrs. 22hrs. 3 4hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : - 1.5Pas
: : :
Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON QL THINNER, Thinning: 0 - 10 % by Volume UMEGUARD PU
Packaging Notes
Two pack product 1.The surface must be thoroughly cleaned by thinner wiping of fresh water washing to remove salt, dirt, oil, grease, chalking and impurities.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SUPER H
UMEGUARD
Sep.2006
No. 6197
SUPER H
UMEGUARD Super H, is a high solid paint based on a combination of epoxy resin, special abrasive resistant agent and polyamide amine resin. It provides excellent abrasive resistance and fast cures to a hard paint film which have excellent anti-abrasion property. It is suitable for protection of cargo hold as a finish coat.
TECHNICAL DATA
Type
High solid Epoxy/Polyamide amine coating
Recommened Cargo hold, Void space, Cofferedam, Engine room. Use Inside of accommodation space.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 83 : 17 [by volume] Grey Base = 17.5, Hardener = 24.5 [degC] 75 (+-2) [volume %] 248 [g/L] 2 0.133 - 0.2 [L/m ] : WET 133 - 200 [micron] DRY 100 - 150 [micron]
15 C 1hrs. 16hrs. 16hrs. 10days 14hrs.
o
(D.F.T. 150micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 15 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0 Pas
: : :
Tip No. : (GRACO)619,719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume UMEGUARD SUPER H PRIMER -
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curings. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval. 3.Too much solvent results in reduced sag resistance and paint film property. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
May.2006
No. 6195
SH Pr
UMEGUARD SUPER-H PRIMER, is a exclusive epoxy primer for UMEGUARD SUPER-H, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent resistance to dry hand cargo such as coal and iron-one. It is suitable for protection at cargo hold as a primer coat.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint for Cargo hold of the bulk carrier. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Grey, Red brown Base = 23.1, Hardener = 24.9 [degC] 63 (+-2) [volume %] 401 [g/L] 2 0.16 - 0.32 [L/m ] : WET 159 - 317 [micron] DRY 100 - 200 [micron]
10 C 5.5hrs. 18hrs. 18hrs. * 14hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, BANNOH THINNER Thinning: 0 - 15 % by Volume CERABOND, etc. UMEGUARD SUPER-H
Packaging Notes
Two pack product 1.* Kindly consult with CMP sales office. 2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
May.2006
No. 6196
SH Pr QD
UMEGUARD SUPER-H PRIMER QD, is a exclusive epoxy primer for UMEGUARD SUPER-H in winter season, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent resistance to dry hand cargoes such as coal and iron-one. It is suitable for protection of cargo hold as a primer coat.
TECHNICAL DATA
Type
Epoxy paint
Recommened Anti-corrosive paint cargo hold of the bulk carrier. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 81 : 19 [by volume] Grey, Red brown Base = 23.1, Hardener = 24.9 [degC] 63 (+-2) [volume %] 394 [g/L] 2 0.16 - 0.32 [L/m ] : WET 159 - 317 [micron] DRY 100 - 200 [micron]
5 C 5hrs. 17hrs. 17hrs. * 6hrs.
o
(D.F.T. 200micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
30 C
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pas
: : :
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume CERABOND, etc. UMEGUARD SUPER-H
Packaging Notes
Two pack product 1.* Kindly consult with CMP sales office. 2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX
UG
Feb.2006
No. 6166
SX
UMEGUARD SX, surface tolerant paint, is a epoxy type paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil.
TECHNICAL DATA
Type
Surface tolerant anti-corrosive paint used as primer and topcoat
Recommened Cargo hold, Inside and outside of accommodation space, Deck,Void space, Cofferdam, Engine Use room, Pipe line, Other steel structures, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Grey, Black, White, Red brown Base = 23.5, Hardener = 19.0 [degC] 57 (+-2) [volume %] 435 [g/L] 2 0.176 - 0.439 [L/m ] : WET 176 - 439 [micron] DRY 100 - 250 [micron]
5 C 4.5hrs. 44hrs. 44hrs. 24hrs.
o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON THINNER, Thinning: 0 - 5 % by Volume WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER EPICON MARINE FINISH HB, ACRI 700, etc.
Packaging Notes
Two pack product 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.As nature of epoxy coatings UMEGURD SX can not avoid chalking and fading on UV exposure. 3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX HS
UMEGUARD
Feb.2006
No. 6193
SX HS
UMEGUARD SX HS, surface tolerant paint, is a modified epoxy paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance.It has excellent resistance to sea water and cathodic protection.
TECHNICAL DATA
Type
Modified anticorrosive epoxy paint
Recommened Anti-corrosive paint for ship's bottom ,Cargo hold, Inside and outside of accommodation space, Use Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.For use at Maintenance and Repair.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 74 : 26 [by volume] Grey, Black, Red brown, Green Base = 17.5, Hardener = 24.5 [degC] 72 (+-2) [volume %] 286 [g/L] 2 0.139 - 0.278 [L/m ] : WET 139 - 278 [micron] DRY 100 - 200 [micron]
5 C
o
(D.F.T. 150micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER EPICON MARINE HB, UNY MARINE, etc.
Packaging Notes
Two pack product 1.In confined spaces , ventilation is required during application and curing to remove solvent vapours and promote curing. 2.As nature of modified epoxy coatings UMEGURD SX HS can not avoid chalking and fading on UV exposure. 3.If painting interval is exceeded,it may be necessary to roughen the surface. 4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX QD
UG
Feb.2006
No. 6135W
SX QD
UMEGUARD SX QD, is a epoxy type paint. It gives excellent physical properties such as adhesion , toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil. In addition , it has excellent drying properties at low temperatures.
TECHNICAL DATA
Type
Epoxy type paint
Recommened Cargo hold, Inside and outside of accomdation space, Void space, Cofferdam, Engine room, Pipe Use line, Other steel structures, etc.
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 85 : 15 [by volume] Grey, Black, White, Red brown Base = 23.5, Hardener = 19.0 [degC] 57 (+-2) [volume %] 435 [g/L] 2 0.176 - 0.439 [L/m ] : WET 176 - 439 [micron] DRY 100 - 250 [micron]
-5 C 8hrs. 40hrs. 40hrs. o
(D.F.T. 250micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max Pot Life
Condition of Application
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 20 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pas
: : :
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec] BISCON THINNER, Thinning: 0 - 15 % by Volume WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER -
Packaging Notes
Two pack product 1. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing. 2.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity. 3.Too much solvent results in reduced sag resistance and paint film property. 4.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases. 5.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 10
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UNY MARINE
UM
Feb.2006
No. 5510A
UNY MARINE, based on polyurethane resin, has excellent gloss retention, durability and chemical resistance, etc. It is suitable for protection of outside of superstructure of steel ships.
TECHNICAL DATA
Type
Polyurethane finish paint
Recommened Glossy finish coat on outside of superstructure, deck and fittings. Use
Information
Mixing Ratio : Color : Flash Point : Solid by volume : VOC : Coverage(Theoretical): Film Thickness
Base : Hardener = 80 : 20 [by volume] White, As specified Base = 23, Hardener = 30 [degC] 44 (+-2) [volume %] 493 [g/L] 2 0.068 - 0.113 [L/m ] : WET 113 [micron] DRY 50 [micron]
5 C 50mins. 12hrs. 8hrs. 24hrs.
o
(D.F.T. 50micron) Drying Time Surface Dry Hard Dry Painting Interval Min Max * Pot Life
Condition of Application
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0 degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
: : :
Tip No. : (GRACO)515,615,715,813 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec] UNY MARINE THINNER, Thinning: 5 - 15 % by Volume BANNOH 500, BANNOH 200, EPICON MARINE UNDERCOAT M, etc. -
Packaging Notes
Two pack product 1.* Please refer to the painting specifications. 2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.