Professional Documents
Culture Documents
Close Window
Assessment System
Exam Viewer - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the Enterprise (Version
4.0)
Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item.
Use of the exam information in the Exam Viewer is subject to the terms of the Academy Connection Website Usage Agreement between you
and Cisco. The purpose of the Exam Viewer is to support instruction while not compromising exam security for other Cisco Networking
Academies or students. This material should not be distributed outside a proctored and controlled setting. If misuse is found, action will be
taken to limit access to assessment content. Please remember to logout and close your browser window after using the Exam Viewer.
Max Value = 2
Max Value = 2
Refer to the exhibit. Users on the 172.30.20.0/24 network are unable to access any of the servers located on the 192.168.0.0/23
network. Given the network topology and OSPF configuration, what two problems exist in this network? (Choose two.)
There is a routing loop occurring between all three routers.
There is a network statement missing.
Network 172.30.20.0 has an incorrect wildcard mask.
The OSPF area configuration is incorrect.
/23 is an invalid subnet mask for the 192.168.0.0 network.
Max Value = 2
Refer to the exhibit. A network administrator must manually summarize all IP addresses on the POP router for the ISP. Which one is the
correct summary address?
192.168.0.0/22
192.168.0.0/23
192.168.0.0/24
192.168.0.0/25
Max Value = 2
Refer to the exhibit. A network support technician has been asked to set an IP address on one of the FastEthernet interfaces on a new
router. What is causing the interface to reject the address?
The IP address is already in use.
The technician is using a network address.
The technician is using the wrong subnet mask for /26.
The technician must enable VLSM on the interface.
Max Value = 2
pruning
transparent
Max Value = 2
Max Value = 2
Refer to the exhibit. R1 and R2 are connected via serial interfaces. Both interfaces show that there is Layer 2 connectivity between
them. The administrator verifies that CDP is operational; however, pings between the two interfaces are unsuccessful. What is the cause
of this connectivity problem?
no set loopback
incorrect subnet mask on R2
incompatible bandwidth
incorrect IP address on R1
incompatible encapsulation
Max Value = 2
Max Value = 2
Refer to the exhibit. R3 is announcing all displayed internal networks to R4 with the summary address 10.1.0.0/22. Which address will
be most appropriate for Network A?
10.0.0.0/24
10.1.4.0/24
10.1.0.0/24
10.1.0.0/23
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Max Value = 2
Refer to the exhibit. The network administrator wants to restrict the Production network from accessing the HR network. All other traffic
will have access to all networks. Which combination of interface and direction should the administrator use to apply the ACL?
Fa0/1, out
Fa1/0, out
Fa0/1, in
Fa1/0, in
Max Value = 2
Refer to the exhibit. The network consists of a single OSPF area. All router priorities are at the default value and no loopback addresses
are configured. The router interface IP addresses are displayed. Which two routers are likely to be elected as the DRs? (Choose two.)
R1
R2
R3
R4
R5
R6
Max Value = 2
Refer to the exhibit. Which IP address can be assigned to the Fa0/0 interface of R1 to enable host A to access host B?
192.168.1.32/26
192.168.1.64/26
192.168.1.126/26
192.168.1.129/26
Max Value = 2
Refer to the exhibit. The command that is displayed was run on a switch with 24 FastEthernet ports. Why are some ports missing from
VLAN1?
The missing ports are administratively down.
The missing ports are not configured for STP.
The missing ports are not connected to any active device.
The missing ports are configured for trunk ports.
Max Value = 2
Refer to the exhibit. The routing protocols are configured with their default settings. Which two statements are true about the path or
paths that R1 will choose to the 192.168.2.0/24 network? (Choose two.)
If only EIGRP is configured on the network, only the path R1->R3 will be installed in the routing table.
If OSPF and RIPv2 are both configured on the network, only OSPF paths will be installed in the routing table.
If EIGRP and OSPF are both configured on the network, only EIGRP paths will be installed in the routing table.
If EIGRP and RIPv2 are both configured on the network, only RIPv2 paths will be installed in the routing table.
If RIPv2 is the routing protocol, the two equal cost paths (R1-R2-R3 and R1-R4-R3) will be installed in the routing table.
Max Value = 2
Refer to the exhibit. The network administrator enters the command that is shown in the exhibit and then issues the show ip route
command. The route added by the network administrator is missing from the routing table. What is the reason for this?
This static route is providing a backup to the existing route to 192.168.1.0 /24.
The route is incorrectly configured.
Dynamic updates are always preferred over static routes.
The FastEthernet0/0 interface is administratively down.
Max Value = 2
Refer to the exhibit. R2 receives the dynamic update R 192.168.2.0/24 [120/2] via 10.1.1.2, 00:00:15, Serial0/0/0.
The update information will replace the existing routing table entry.
The routing protocol will not replace the existing route with this new routing update.
The existing routing table entry will be purged from the routing table and all routers will attempt to converge.
Max Value = 2
Refer to the exhibit. All routers are configured to use the EIGRP routing protocol, and the network administrator has configured the serial
interface with the displayed commands. Which summary route will show in the routing table of R1 as a result of these commands?
a route pointing to the FastEthernet0/0 interface
a route pointing to the Serial0/0/0 interface
a route pointing to the Null0 interface
a route pointing to the loopback0 interface
Max Value = 2
Max Value = 2
Refer to the exhibit. All routers are configured to use the OSPF protocol with default settings. Which router will act as the BDR if all
routers start at the same time?
R1
R2
R3
R4
Max Value = 2
Refer to the exhibit. Which two facts can be determined from the output? (Choose two.)
The router ID of R2 is 192.168.100.65.
R2 has established adjacencies with three routers.
R2 is not receiving hellos from neighbor 192.168.100.66.
R2 is connected to an Ethernet network that consists of two routers.
Neighbor 192.168.100.3 will become the DR if the current DR becomes unavailable.
Max Value = 2
Refer to the exhibit. The network administrator has configured R1, R2, and R3 to use RIPv2, and the network is fully converged. The
hosts on the internal network are able to access R2, but they are unable to access the Internet.
Max Value = 2
Max Value = 2
Refer to the exhibit. The network administrator configured the routers using the displayed commands, but the network fails to converge.
What can the network administrator do to solve this problem?
Issue the network commands correctly on both routers.
Configure the wildcard masks correctly on both routers.
Issue the no auto-summary command.
Configure both routers with different autonomous numbers.
Max Value = 2
Refer to the exhibit. Both routers are configured to use the EIGRP routing protocol. The network administrator wants to enable manual
summarization by issuing the displayed command.
Max Value = 2
Reset View
Close Window
All contents copyright ©2001-2008 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.