Professional Documents
Culture Documents
2
Given the following commands:
What three conclusions can be determined based on the commands used on the
router? (Choose three.)
Bandwidth, load, delay, and reliability are metrics used for route selection.
3
What is indicated when an EIGRP route is in the passive state?
The route has the highest path cost of all routes to that destination network.
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
The route must be confirmed by neighboring routers before it is put in the active state.
The route is a feasible successor and will be used if the active route fails.
4
What two problems may occur if the EIGRP default bandwidth for a serial link is
higher than the actual bandwidth? (Choose two.)
Routing updates will arrive too quickly for receiving routers to process.
5
What is the default administrative distance for EIGRP internal routes?
70
90
100
110
120
255
6
A network administrator issues the command show ip route and sees this line of
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
output:
What two pieces of information can be obtained from the output? (Choose two.)
Refer to the exhibit. Which statement is true about the EIGRP authentication
configuration?
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
RTA and RTB will not accept updates from each other because key 1 on RTB does
not match RTA.
RTA and RTB will not accept updates from each other because the key chain names
do not match.
The ip authentication mode AS does not match the locally configured AS.
8
Which Layer 4 protocol does EIGRP use to provide reliability for the transmission of
routing information?
DUAL
IP
PDM
RTP
TCP
UDP
Refer to the exhibit. Routers RTR-1 and RTR-3 are completely configured. The
administrator needs to configure the routing protocol on router RTR-2 so that
communication occurs throughout the network. Which group of commands will
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
10
What prevents RIPv1 updates from being correctly advertised?
a mismatch between the configured bandwidth and the actual bandwidth of a link
11
What does a router that is running RIP use to determine the best path to take when
forwarding data?
12
What is the purpose of the network command when RIP is being configured as the
routing protocol?
It identifies all of the destination networks that the router is allowed to install in its
routing table.
It identifies the directly connected networks that will be included in the RIP routing
updates.
13
How do EIGRP routers establish and maintain neighbor relationships?
14
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. Routers A and B have EIGRP configured and automatic
summarization has been disabled on both routers. Which router command will
summarize the attached routes?
15
How often does RIPv2 send routing table updates, by default?
every 30 seconds
every 45 seconds
every 60 seconds
every 90 seconds
16
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
The Ethernet networks on RTR-2 and RTR-3 were not entered correctly in the
network statements on these routers.
17
What two statements are correct regarding EIGRP authentication? (Choose two.)
EIGRP authentication requires that both routers have the same key chain name.
EIGRP authentication uses varying levels of WEP to encrypt data exchanged between
routers.
EIGRP authentication can be configured on one router and updates from this router
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
18
When should EIGRP automatic summarization be turned off?
19
What is the maximum number of hops that RIP will attempt before it considers the
destination unreachable?
14 hops
15 hops
16 hops
17 hops
20
What two statements are true regarding EIGRP tables? (Choose two.)
The topology table shows whether a route is in the passive or active state.
The routing table shows the amount of time elapsed since a router adjacency was
formed.
21
Refer to the exhibit. Which statement is true about the output from the show ip
protocols command?