Professional Documents
Culture Documents
DE710-TRACK
Parts Manual
EXPLORATION DRILL DE710-TRACK REVISION A
Sandvik Mining and Construction Australia 100 Grindle Road, Rocklea QLD Australia 4106
SANDVIK MINING AND CONSTRUCTION STANDARD EQUIPMENT WARRANTY (Effective for Equipment sold after 01 February 2010)
1 SANDVIK MINING AND CONSTRUCTION (as defined in the General Conditions of Sale) warrants new Drill Rigs, LHDs, Dump Trucks, Breaking, Crushing and Screening, Mechanical Cutting, Projects & Systems, Fire Suppression and Automation Systems (PRODUCTS) supplied by SANDVIK MINING AND CONSTRUCTION to be free from defects in material and workmanship. 2 The warranty periods for the equipment is the following: i) Breaking, Crushing and Screening a. Breakers six (6) months from the date of purchase based on a single shift use of ten (10) hours per shift, plus another six (6) months after completion of the six (6) monthly service inspection. b. Crushing & Screening (both mobile and fixed plant) twelve (12) months or 2000 hours from date of commissioning acceptance by Purchaser. Drill Rigs a. Top hammer drill rigs twelve (12) months, except hydraulic rock drills twelve (12) months or one thousand (1000) percussion hours, whichever comes first. b. Down the hole drill rigs twelve (12) months or two thousand (2000) engine hours whichever comes first, except down the hole hammer three (3) months. c. Rotary and waterwell drill rigs twelve (12) months or two thousand (2000) engine hours whichever comes first, except the following components carry additional warranty: Air End 24 months unlimited hours; Rotary Head - 12 months unlimited hours; Piston Pumps and Motors 12 months unlimited hours; Feed and Jack Cylinders 12 months unlimited hours. d. Exploration drill rigs twelve (12) months or two thousand (2000) engine hours whichever comes first.
ii)
iii) Load & Haul a. LHDs and Trucks (12) months or two thousand (2000) engine hours (operating hours for electric equipment), whichever comes first. b. Shuttle Cars and Utility Vehicles twelve (12) months or two thousand (2000) engine hours, whichever comes first. c. Quick Detach System Appliances six (6) months. iv) Mechanical Cutting a. Twelve (12) months from date of commissioning acceptance by Purchaser. v) Projects & Systems a. Material handling twelve (12) months from date of commissioning acceptance by Purchaser. b. Onboard automation within the machine (LHD, truck, drilling rig, etc.) follows the warranty terms of the basic machine: twelve (12) months or two thousand (2000) operating hours, whichever comes first. c. Automation system excluding onboard automation: twelve (12) months after commissioning is completed (Site Acceptance Test completed and signed-off) or eighteen (18) months after shipment of components, whichever comes first. d. Plants twelve (12) months from date of commissioning acceptance by Purchaser.
vi) Fire Suppression a. Twelve (12) months from date of commissioning acceptance by Purchaser.
3 All the above mentioned periods are calculated from the date of start-up inspection at the first end user. Under no circumstances will the warranty period exceed eighteen (18) months from the delivery to Purchaser. Any liability whatsoever to any party, other than the first end user is expressly disclaimed. The Purchaser agrees and acknowledges that all warranties shall immediately terminate in the event that the Purchaser expressly or impliedly purports to transfer or assign or otherwise any of its rights under this warranty to a third party. Any attempt by the Purchaser to transfer or assign the warranties provided by SANDVIK MINING AND CONSTRUCTION to any third party shall be void, unless Sandvik has provided its prior written consent to the Purchaser. 4 The unit start-up inspection form/ warranty registration card shall be filled in, signed by the end user and sent to SANDVIK MINING AND CONSTRUCTION representative within fourteen (14) days from start-up inspection. The warranty period starts from the date the end user signs the start-up inspection form. 5 The engine warranty registration shall be completed with local engine representative. All engine warranties shall be handled with local OEM engine representative. 6 The completed warranty registration form must be received by SANDVIK MINING AND CONSTRUCTION representative before any claims for warranty will be processed. 7 This warranty does not cover: i) natural wear and tear of the equipment, normal maintenance service such as but not limited to, engine tune-ups, adjustments and inspections or normal replacement items (such as service filters), and damage resulting there from; consumables such as but not limited to, seals, filters, hoses, v-belts, tyres, fittings, screws, bolts, washers, rock drill connecting pieces, chucks, diaphragms, pick holders, conveyor chain, spray nozzles, idlers, trailing cable, rubber skirting, pick bushes, teeth and knives, mantles and concaves, manganese wear parts etc;
ii)
iii) parts which can be repaired or corrected with minimum action such as but not limited to, changing of seals, tightening or adjustment; iv) damage caused by breakage of the shank adaptor (excluding material or workmanship failure in genuine SANDVIK shank adaptor); v) damage caused by the Purchasers failure to store, maintain or operate the equipment properly, or due to overloading or failure to pay proper attention to service and operating instructions or caused by accident or caused by working beyond rated capacities or exceeding or not meeting recommended power inputs;
vi) damage caused by negligence or failure of PURCHASER to maintain the equipment in accordance with SANDVIK MINING AND CONSTRUCTIONs maintenance recommendations, documented service history is required; vii) damage which is caused by but not limited to, operating conditions such as deep and/or aggressive water, poor roadways, dust, poor ventilation, where components, which are designed and manufactured according to industrial standards, fail prematurely; viii) any defect or damage in materials or design provided by the PURCHASER, which are a consequence of the PURCHASERS action or stipulation affecting quality or structure; ix) any parts or components manufactured or supplied by third parties or damage caused by such parts or components to the PRODUCTS; x) any costs such as labour, accommodation, meals travel and similar costs or any transportation;
xi) any direct or indirect consequential damage including but not limited to loss of revenue or profit, loss of production or loss of use of any equipment; xii) Product improvements/ updates made available by Sandvik, unless otherwise specified. 8 This Equipment warranty contains the entire warranty terms and conditions between Sandvik Mining and Construction and the Purchaser. Notwithstanding anything to the contrary contained in this warranty or otherwise, the Purchaser expressly waives all claims against Sandvik Mining and Construction (and against its parent company, affiliates, contractors, subcontractors, consultants, employees, agents and vendors) for any consequential, incidental, indirect, special, exemplary or punitive damages, including, but not limited to, loss of actual or anticipated profits, revenues or product; loss by reason of shutdown or non-operation; increased expense of manufacturing, operation, borrowing or financing; loss of use, productivity or shop space; or increased cost of capital, and regardless of whether any such claim arises out of breach of contract or warranty, tort (including negligence), product liability, indemnity, contribution, strict liability or any other legal theory. All limitations in this warranty on Sandvik Mining and Constructions liability shall apply notwithstanding the fact that Sandvik Mining and Constructions warranties fail of their essential purpose or are held to be invalid or unenforceable. Under no circumstances and in no conditions, shall SANDVIK MINING AND CONSTRUCTION's liability whether in respect of one claim or in the aggregate, arising out of any contract, exceed the purchase price payable under the contract for such part in which the liability shall arise. On receipt of notification of a warranted defect, SANDVIK MINING AND CONSTRUCTION shall remedy the defect at its own discretion in accordance with these terms of warranty. Warranty claims less than fifty Euros (EUR 50) or the equivalent in another currency are not considered by SANDVIK MINING AND CONSTRUCTION. No claim will be considered, and this warranty will be considered null and void, if other than GENUINE SANDVIK MINING AND CONSTRUCTION SPARE PARTS are used in the equipment or if GENUINE SANDVIK MINING AND CONSTRUCTION SPARE PARTS are dismounted and used in another product than the PRODUCT originally supplied to the PURCHASER by SANDVIK MINING AND CONSTRUCTION. All Warranty claims need to have a proof of purchase which may include but not limited to: i) Copy of invoice or order number; or ii) Job Charge out report. 1. Warranty claims must be sent in writing using a "SANDVIK MINING AND CONSTRUCTION Warranty Claim" form. Warranty claims concerning the failure in rock drills should also include the "Drifter Failure Report" form. Claims should include digital photographs of the failure where appropriate. The forms shall be completely filled in and delivered to SANDVIK MINING AND CONSTRUCTION representative within fourteen (14) days from the time when the PURCHASER discovers or should have discovered the alleged defect. Claims lodged after this period will be declined. Only one failure should be reported for each claim. The warranty claim form should be sent to your local SANDVIK MINING AND CONSTRUCTION representative. The obligation of SANDVIK MINING AND CONSTRUCTION under this warranty is limited, at PURCHASERs option, to: i) ii) refund the part at its stock replenishment order price; or replace the part, free of charge, DDP (delivered, duty paid, Incoterms 2000) at the place of business of the SANDVIK MINING AND CONSTRUCTION representative.
10
11
12
13
14
15
16 The warranty of a replaced or repaired part expires at the same time as the original warranty of the supplied
equipment.
17 The PURCHASER shall retain the claimed part for 90 days from claim settlement, for SANDVIK MINING AND CONSTRUCTION's inspection and on request the alleged defective part shall be sent as directed by SANDVIK MINING AND CONSTRUCTION and at SANDVIK MINING AND CONSTRUCTION'S cost to a destination designated by SANDVIK MINING AND CONSTRUCTION. No part may be returned to SANDVIK MINING AND CONSTRUCTION without SANDVIK MINING AND CONSTRUCTION'S prior written consent. After warranty handling, the title to the defective parts shall be transferred to SANDVIK MINING AND CONSTRUCTION. 18 Return parts to your local SANDVIK MINING AND CONSTRUCTION representative. 19 APPEAL PERIOD FOR EACH SANDVIK MINING AND CONSTRUCTIONS DECISION IN WARRANTY CLAIM IS FOURTEEN (14) DAYS AS OF THE DATE OF DECISION AFTER WHICH THE SAID DECISION IS FINAL. 20 This warranty is in lieu of all other warranties or conditions express, implied or statutory, including, but not limited to, warranties of merchantability and fitness for a particular purpose. No other warranties express or implied are given unless they are expressly given by SANDVIK MINING AND CONSTRUCTION in writing. 21 This warranty shall not be suspended on the grounds of non-use, intermittent use or for any other reason.
SANDVIK MINING AND CONSTRUCTION STANDARD SPARE PARTS WARRANTY (Effective for Spare Parts sold after 01 February 2010)
1 SANDVIK MINING AND CONSTRUCTION (as defined in the General Conditions of Sale) warrants new spare parts supplied by SANDVIK MINING AND CONSTRUCTION to be free from defects in material and workmanship in accordance with industry standards current at the time of sale when the parts are used as a part of SANDVIK MINING AND CONSTRUCTION PRODUCTS. 2 The warranty periods are as follows: i) hydraulic rock drills mounted on used drill rig six (6) months or five hundred (500) percussion hours, whichever comes first; ii) for other spare parts the warranty period is three (3) months from date of fitment, with a maximum of six (6) months from date of delivery; iii) all major components mounted to used equipment six (6) months or five hundred (500) operating hours, whichever comes first. 3 All the above mentioned periods are calculated from the date of delivery to the end user. Any liability whatsoever to any party other than the first end user is expressly disclaimed. 4 The engine warranty registration shall be completed with local engine representative. All engine warranties shall be handled with local engine representative. 5 This warranty does not cover: i) natural wear and tear of the spare part and damage resulting there from;
ii)
consumables such as seals, filters, hoses, v-belts, tyres, fittings, screws, bolts, washers and rock drill connecting pieces, chucks, diaphragms, pick holders, conveyor chain, spray nozzles, idlers, trailing cable, rubber skirting, pick bushes, teeth & knives, mantles & concaves, manganese wear parts, G.E.T., etc; parts which can be repaired or corrected with minimum action such as changing of seals, tightening or adjustment; damage caused by breakage of the shank adaptor (excluding material or workmanship failure in genuine SANDVIK shank adaptor); damage caused by the Purchasers failure to store, maintain or operate the spare part properly, or due to overloading or failure to pay proper attention to service and operating instructions or caused by accident or caused by working beyond rated capacities or exceeding recommended power inputs or not meeting required power inputs; damage caused by negligence or failure of PURCHASER to maintain the equipment in accordance with SANDVIK MINING AND CONSTRUCTIONs maintenance recommendations, documented service history is required;
iii)
iv)
v)
vi)
vii) damages, which are caused by operating conditions such as deep and/or aggressive water, dust, poor ventilation, where components, which are designed and manufactured according to industrial standards fail prematurely; viii) any defect or damage in materials or design provided by the PURCHASER, which are a consequence of PURCHASERS action or stipulation affecting quality or structure; ix) any parts or components manufactured or supplied by third parties or damage caused by such parts or components to the PRODUCTS; any costs such as labour, accommodation, meals, travel and similar costs or any transportation; any indirect or consequential damage including but not limited to loss of profit, loss of production or loss of use of equipment;
x) xi)
xii) Product improvements/ updates made available by Sandvik. 6 Warranty claims less than fifty Euros (EUR 50) or the equivalent in another currency are not considered by SANDVIK MINING AND CONSTRUCTION. 7 All Warranty claims need to have a proof of purchase which may include but not limited to: i) Copy of invoice or order number; or ii) Job Charge out report.
8 This Parts warranty contains the entire warranty terms and conditions between Sandvik Mining and
Construction and the Purchaser. Notwithstanding anything to the contrary contained in this warranty or by way or otherwise, the Purchaser expressly waives all claims against Sandvik Mining and Construction (and against its parent company, affiliates, contractors, subcontractors, consultants, employees, agents and vendors) for any consequential, incidental, indirect, special, exemplary or punitive damages, including, but not limited to, loss of actual or anticipated profits, revenues or product; loss by reason of shutdown or non-operation; increased expense of manufacturing, operation, borrowing or financing; loss of use, productivity or shop space; or increased cost of capital, and regardless of whether any such claim arises out of breach of contract or warranty, tort (including negligence), product liability, indemnity, contribution, strict liability or any other legal theory. All
limitations in this warranty on Sandvik Mining and Constructions liability, shall apply notwithstanding the fact that Sandvik Mining and Constructions warranties fail of their essential purpose or are held to be invalid or unenforceable. 9 In order to be able to avail himself of the rights under this Warranty, the PURCHASER shall notify SANDVIK MINING AND CONSTRUCTION in writing without delay of any defects that have appeared and shall give SANDVIK MINING AND CONSTRUCTION every opportunity of inspecting and remedying them. 10 On receipt of notification of a warranted defect, SANDVIK MINING AND CONSTRUCTION shall remedy the defect at its own discretion in accordance with these terms of warranty. 11 The purchase Order Number and or Sandvik Invoice Number must be received by SANDVIK MINING CONSTRUCTION representative before any claims for warranty will be processed. AND
12 Under no circumstances and in no conditions, shall SANDVIK MINING AND CONSTRUCTION's liability for any singular or aggregate claim arising under any contract or otherwise exceed the contract purchase price of the part from which the liability arises. 13 No claim will be considered, and this warranty will be considered null and void, if other than GENUINE SANDVIK MINING AND CONSTRUCTION SPARE PARTS and all consumables as originally installed by SANDVIK MINING AND CONSTRUCTION are used in the PRODUCT. 14 Warranty claims must be sent in writing using a "SANDVIK MINING AND CONSTRUCTION Warranty Claim" form. Warranty claims concerning the failure in rock drills should also include the Drifter Failure Report form. The forms shall be completely filled in and be delivered to SANDVIK MINING AND CONSTRUCTION within fourteen (14) days from the time when the PURCHASER discovers or should have discovered the alleged defect. The date of the Spare Part delivery to the end user must be proved in writing. Only one failure should be reported for each claim. The warranty claim form should be sent to your local SANDVIK MINING AND CONSTRUCTION representative. 15 The obligation of SANDVIK MINING AND CONSTRUCTION under this warranty is limited, at PURCHASERs option, to: i) refund the part at its stock replenishment order price; or ii) replace the part, free of charge, DDP (delivered, duty paid, Incoterms 2000) at the place of of the SANDVIK MINING AND CONSTRUCTION representative. business
16 The PURCHASER shall retain and appropriately store the claimed part to allow accurate assessment by SANDVIK MINING AND CONSTRUCTION until the claim is settled. On request the alleged defective part shall be sent as directed by SANDVIK MINING AND CONSTRUCTION and at SANDVIK MINING AND CONSTRUCTION'S cost, to a destination designated by SANDVIK MINING AND CONSTRUCTION. No part may be returned to SANDVIK MINING AND CONSTRUCTION without SANDVIK MINING AND CONSTRUCTION's prior written consent. After warranty handling, the title to the defective part will be transferred to SANDVIK MINING AND CONSTRUCTION. 17 APPEAL PERIOD FOR EACH SANDVIK MINING AND CONSTRUCTIONS DECISION IN WARRANTY CLAIM IS FOURTEEN (14) DAYS AS OF THE DATE OF DECISION AFTER WHICH THE SAID DECISION IS FINAL. 18 This warranty is in lieu of all other warranties or conditions express, implied or statutory, including, but not limited to warranties of merchantability and fitness for a particular purpose. No other warranties express or implied are given unless they are expressly given by SANDVIK MINING AND CONSTRUCTION in writing. 19 This warranty shall not be suspended on the grounds of non-use, intermittent use or for any other reason.
SANDVIK MINING AND CONSTRUCTION STANDARD FOR CONSUMABLES (Effective for Consumables sold after 01 February 2010)
1. SANDVIK MINING AND CONSTRUCTION (as defined in the General Conditions of Sale) warrants that Sandvik Consumables delivered are free of defects, faults in workmanship, manufacture and material, free of any liens or encumbrances and will be of the standard quality and not that such Goods will accomplish any particular result. 2. The warranty periods are as follows: i) ii) 3. Sandvik Drilling Consumables three (3) months from date of delivery; Manganese wear parts, MGT, G.E.T. three (3) months.
Any repair or replacement to SANDVIK Consumables provided by SANDVIK MINING AND CONSTRUCTION will be subject to the same warranty, from the date of repair or replacement.
4. All the above mentioned periods are calculated from the date of delivery to the end user. Any liability whatsoever to any party other than the first end user is expressly disclaimed. 5. This warranty does not cover: i) natural wear and tear of the spare part and damage resulting there from; ii) damage caused by breakage of the shank adaptor; i) damage caused by the Purchasers failure to store, maintain or due to overloading or failure to pay proper attention to operating instructions or caused by accident or caused by working beyond rated capacities or exceeding recommended power inputs or not meeting required power inputs; ii) any defect or damage in materials or design provided by the PURCHASER, which are a consequence of PURCHASERS action or stipulation affecting quality or structure; iii) any costs such as labour, accommodation, meals, travel and similar costs or any transportation; iv) any indirect or consequential damage including but not limited to loss of profit, loss of production or loss of use of equipment. 6. Warranty claims less than fifty Euros (EUR 50) or the equivalent in another currency are not considered by SANDVIK MINING AND CONSTRUCTION. 7. This Consumables warranty contains the entire warranty terms and conditions between Sandvik Mining and Construction and the Purchaser. Notwithstanding anything to the contrary contained in this warranty or by way or otherwise, the Purchaser expressly waives all claims against Sandvik Mining and Construction (and against its parent company, affiliates, contractors, subcontractors, consultants, employees, agents and vendors) for any consequential, incidental, indirect, special, exemplary or punitive damages, including, but not limited to, loss of actual or anticipated profits, revenues or product; loss by reason of shutdown or nonoperation; increased expense of manufacturing, operation, borrowing or financing; loss of use, productivity or shop space; or increased cost of capital, and regardless of whether any such claim arises out of breach of contract or warranty, tort (including negligence), product liability, indemnity, contribution, strict liability or any other legal theory. All limitations in this warranty on Sandvik Mining and Constructions liability, shall apply notwithstanding the fact that Sandvik Mining and Constructions warranties fail of their essential purpose or are held to be invalid or unenforceable.
8. In order to be able to avail himself of the rights under this Warranty, the PURCHASER shall notify SANDVIK MINING AND CONSTRUCTION in writing without delay of any defects that have appeared and shall give SANDVIK MINING AND CONSTRUCTION every opportunity of inspecting and remedying them. 9. On receipt of notification of a warranted defect, SANDVIK MINING AND CONSTRUCTION shall remedy the defect at its own discretion in accordance with these terms of warranty. 10. The purchase Order Number and or Sandvik Invoice Number must be received by SANDVIK MINING AND CONSTRUCTION representative before any claims for warranty will be processed. 11. Under no circumstances and in no conditions, shall SANDVIK MINING AND CONSTRUCTION's liability for any singular or aggregate claim arising under any contract or otherwise exceed the contract purchase price of the part from which the liability arises. 12. No claim will be considered, and this warranty will be considered null and void, if other than GENUINE SANDVIK MINING AND CONSTRUCTION CONSUMABLES are used with the equipment. 13. Warranty claims must be sent in writing using a "SANDVIK MINING AND CONSTRUCTION Warranty Claim" form. The forms shall be completely filled in and be delivered to SANDVIK MINING AND CONSTRUCTION within fourteen (14) days from the time when the PURCHASER discovers or should have discovered the alleged defect. The date of the Spare Part delivery to the end user must be proved in writing. Only one failure should be reported for each claim. The warranty claim form should be sent to your local SANDVIK MINING AND CONSTRUCTION representative. 14. The obligation of SANDVIK MINING AND CONSTRUCTION under this warranty is limited, at the PURCHASERs option, to: i) refund the consumable at its stock replenishment order price; or ii) replace the consumable, free of charge, DDP (delivered, duty paid, Incoterms 2000) at the place of business of the SANDVIK MINING AND CONSTRUCTION representative. 15. The PURCHASER shall retain and appropriately store the claimed part to allow accurate assessment by SANDVIK MINING AND CONSTRUCTION until the claim is settled. On request the alleged defective part shall be sent as directed by SANDVIK MINING AND CONSTRUCTION and at SANDVIK MINING AND CONSTRUCTION'S cost, to a destination designated by SANDVIK MINING AND CONSTRUCTION. No part may be returned to SANDVIK MINING AND CONSTRUCTION without SANDVIK MINING AND CONSTRUCTION's prior written consent. After warranty handling, the title to the defective part will be transferred to SANDVIK MINING AND CONSTRUCTION. 16. APPEAL PERIOD FOR EACH SANDVIK MINING AND CONSTRUCTIONS DECISION IN WARRANTY CLAIM IS FOURTEEN (14) DAYS AS OF THE DATE OF DECISION AFTER WHICH THE SAID DECISION IS FINAL. 17. This warranty is in lieu of all other warranties or conditions express, implied or statutory, including, but not limited to warranties of merchantability and fitness for a particular purpose. No other warranties express or implied are given unless they are expressly given by SANDVIK MINING AND CONSTRUCTION in writing. 18. This warranty shall not be suspended on the grounds of non-use, intermittent use or for any other reason.
Seq
1 2 3 14 15 16 18 20 22 23 25 26 27 29 40 42 44 52 53 58 61 65 66 69 73 74 75 76 77 78 79 90 91 92 94 95 96 97 1001
Component
710-01 MPL11640-1 MPL11605-2 MPL11940-2 710-15 MPL11634-1 710-18 710-20 MPL11945-1 MPL14230-1 710-25CT 710-26CT MPL14475-1 MPL11670-1 MPL12300-1 MPL14395-1 MPL11620-1 MPL12330-2 MPL11750-1 MPL13230-1 MPL11610-1 MPL11260-1 MPL8610-4 MPL10650-2 MPL11475/50 MPL11630-1 MPL10602-3 710-76CT 710-77CT 710-78 710-79 MPL11350/41 MPL15030-1 MPL8301/38 MPL10639-1 MPL11668_S/50 MPL11273/41 MPL11696-1 HYD14420-1
Item Description
OPTIONS MAST TYPE ASS'Y CROWN ASSEMBLY TRAVERSE CYLINDER ASSEMBLY SIDE RACK ASSEMBLY 200DLS PQ OPTIONS UPPER ROD SLIDE ASS'Y MAST STAY ROD ASSEMBLY OPTIONS MAST PLATFORM ASS'Y OPTIONS PLATFORM STAYROD ASS'Y HEAD CARRIAGE ASS' Y 200DLSPQ DA510 Rotation unit ASSEMBLY OPTIONS ROD SPIN GUARD ASS'Y OPTIONS UPPER BRAKER ASS'Y MAIN WINCH ASSEMBLY WIRELINE WINCH ASS'Y 200DLS B'TOOL ASSEMBLY 200DLS ROD CLAMP ASS'Y DEEPHOLE DUMP SLIDE ASSEMBLY BASE FRAME ASSEMBLY JOHN DEERE JACK LEG ASSEMBLY 200DLS FUEL PIPING ASSEMBLY 200DLS-41 MAST RAISE CYLINDER ASS'Y MAIN DRIVE ASSY 6068TF250 200D PUMP GROUP PIPING ASSY 200D-19 BEAN PUMP W11 200D-07 CONTROL CABINET ASSY 200DLS-50 HYDRAULIC TANK ASSY 200DLS COOLER ASSEMBLY DE710 OPTIONS BOOST PUMP ASS'Y OPTIONS SAFE-T-SPIN ASS'Y OPTIONS SAFE-T-SPIN SUPPT ASSY OPTIONS WIRELINE SPOOLER ASS'Y ELECTRICAL ASSEMBLY 200D-38 HYDRAULIC PIPING ASS'Y DE710XX AIR AND WATER PIPING 200D-38 D COMMISSIONING ITEMS 200DLS NAME/WARNING TAG ASSY 200DLS-5 TRACK CABIN ASSEMBLY 200D-41 D TRACK SUB STRUCTURE ASS'Y HYDRAULIC CIRCUIT DE710XX (CT)
Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Quantity
1 2 2 2 1 1 2 2 4 2 4 2 2 4 2 2 4 2 4 2
Quantity
1 2 1 1 1 1 1 4 4 1 1 4 8 4 4 2 14 4 4 2 4 23
Quantity
1 1 1 4 2 1 2 2 2 1 1 1 6 4 1 2 4 4 20 4 30 16 1 16 4 12 4
Quantity
1 2 2 2 2 2 2 2 4 2 4 4 2
Quantity
1 16 16 2 4 4 4 4 8 2 4 8 1 8 16 8 8
Quantity
1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 3 1 1 1 1 2 2 2 1 1 1 1 1 1
RBR
BALL Component
127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 ..PM26905CH ..PD23776BJ ..PM26904KK ..PM26935KC ..PD23776BK ..PD23776BL ..PD23776BM ..PM26917SS ..PM26907HH ..PM26907NK ..PM28617D19 ..PM26934H ..PM26933A ..PM26944GG ..PM26944KK ..PM26944AA ..WU15185 ..PD23776BN ..PD23776BO ..PM28667C5A ..PM26934K ..PM26934S ..PM26892LK ..PM26889EH .BI00004114 .PD22870AAF .PD22873CA .PD22873CB .PD22873CC .PD22873CD .PD22875BA .PD22893M .PD22928MB .PD22981GA .PD22981GB .PD22981GC .PD22981GD .PD22981GE .PD22981GF .PD22981GG .PD22981GH .PD22981GI .PD22981GJ .PD23753DU .PD23776BE .PD23776BF .PD23776BG .PD23776BQ .PD24433BA .PD24433BB .PD27210EA .PM28610E32 .PM28610F32 .PM28615D13 .PM28615D19
Description
ELBOW MM 90D 1/4"NPT-9/16"JIC 6MJ-14MM, 1.5 ELBOW MF 90D ALL 3/4"NPT RED BUSH 3/4"NPT-1/4"NPT 4MP AIR BREATHER 20 SAE CODE 62-16MJ 90 20 SAE CODE 62 FLANGE HALFS ELBOW MF 90D ALL 1 5/16"JIC ELBOW MM 90D 9/16"UN-9/16"JIC ELBOW MM 90D 1 1/16"UN-3/4"JIC SOCKET SET SCREW CUP POINT CAP NUT 9/16"JIC PLUG 1/8"NPT SOCKET 1/2"NPT SOCKET 3/4"NPT SOCKET 1/8"NPT HYD TUBE 15X1.5; 127 LG SIGHT INDICATOR 5 BAR CHECK VALVE (3/8") GREASE NIPPLE STR 1/4"UNF CAP NUT 3/4"JIC CAP NUT 1 5/16"JIC HEX NIPPLE 7/8"UN x 3/4"NPT HEX NIPPLE 3/8"NPT-9/16"JIC GEAR ASSEMBLY MOTOR; 160CC, SPLINED SHAFT; BALL BEARING CONE THRUST BEARING BALL BEARING STEEL BALL NEEDLE BEARING SPEEDI SLEEVE COMPRESSION SPRING O-RING, 11/16" X7/8"X3/32" O-RING, 9-1/2" X1/8" O-RING, 2-5/16"X3/32" O-RING, 4-3/4"X1/8" POLYURETHANE U-SEAL POLYURETHANE U-SEAL O-RING, 9-1/2"X1/8" O-RING, 7"X7-3/16"X3/32" O-RING, 7-3/4"X7-15/16"X3/32" O-RING, 4-5/8"X1/8" TACHOMETRE PHENOLIC BALL; SCREW-ON COTTER PIN ((1/8" DIAM) HITCH PIN NUT - HEX GR8 1/2" UNF (CASTEL OIL SEAL SHAFT SEAL RETAINING RINGS SET; ( B ROD) HEX HD BOLT 5/16"UNC x 1 1/4" HEX HD BOLT 3/8"UNC x 1 1/4" SKT HD CAP SCREW SKT HD CAP SCREW
Quantity
2 2 1 1 1 2 2 1 1 1 2 2 1 1 4 1 1 1 1 1 1 2 1 1 1 1 2 2 1 1 1 2 21 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 5 18 4 2
RBR
BALL Component
68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 .PM28615D25 .PM28615G51 .PM28615H38 .PM28615H76 .PM28615K32 .PM28615K51 .PM28615K76 .PM28652K .PM28655S41 .PM28680AT .PD22871NA .PD22928MA .PD23776BA .PD23776BC .PD23776BD .PM28651F .PM28651H .PM28652F .PM28667A1A
Description
SKT HD CAP SCREW SKT HD CAP SCREW SKT HD CAP SCREW GR 12.9 SKT HD CAP SCREW GR 12.9 SKT HD CAP SCREW GR 12.9 SKT HD CAP SCREW GR 12.9 SKT HD CAP SCREW GR 12.9 WASHER HELICAL SPRING 3/4" CIRCLIP EXT. DIA 41 NYLOC NUT 3/8" UNC LUBE PUMP COMPRESSION SPRING EXTERNAL SNAP RING (150MM INTERNAL SNAP RING (110MM BORE EXTERNAL SNAP RING (60MM SHAFT WASHER FLAT 3/8 PLATED WASHER FLAT 1/2" PLATED WASHER HELICAL SPRING 3/8" GREASE NIPPLE STR 1/8"NPT
Quantity
4 18 12 4 2 2 2 4 1 2 1 1 2 1 1 4 8 14 1
Quantity
1 1 6 1 1 1 1 0 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 4 17 18 4 4 12 8 4 4 4 4 8 4 4
REV 2
Quantity
1 1 1 1 6 1 1 1 1 1 1 1 2 2 2 1 17 12 6 6 17 1 12 12
Quantity DWG 1
REV 1 REV.3 1 1 1 2 1 1 1 1 4 4 4 4 1 1 1
REV.2
Quantity REV.1
REV.2 1 1 1 1 1 1 2 4 1 1 2 1 1 1 1 2 2 4 2 2 1 0 1 1 1 1 2 2 2 8 12 1 4 2 1 12 2 1 4 32 4 4 4
REV.1 REV.3 REV.1 REV.3 REV.2 REV.8 REV.3 REV.2 REV.3 REV.3 REV.1 REV.1 REV.1 REV.3 REV.2 REV 5
Quantity
1 1 2 14 8 2 14 1 4 4 40 40 4 2 2 2 2 2 2 2 4 1 1 2 1 1 2 2 2 2 4 4 4 1 5 2 4
REV REV REV REV REV REV REV REV REV REV REV
2 1 1 1 2 1 1 2 2 1 1
REV A REV 1 REV 1 REV 1 REV.1 REV A REV 1 REV 1 REV 1 REV 1 REV 1 REV 1 REV 1
Quantity
1 1 1 3 1 1 1 1 2 4 1 1 1 4 1 1 1 2 1 1 1 1 6 1 1 4 2 2 1 1 1 1 1 1 1 1 1 1
REV 2 REV 1
1 1 A 1
10
11
12
1 2 3 4 5 6 1 1 4 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 4 1 1 1 1 4 2 2
13
ITEM QTY PART No. 11612 11647 11648 11656 11697 11698 11806 12231 12232 12233 13253 13254 13255 13258 13268 13276 13278 13511 13969 13970 13977 9122 PD24461GZ PM28661B PM28680AT PM28680BM PART NAME SUPPORT BEAM BASE PLATE JACK LEG COVER STABILIZER OUTER LEG STABILIZER INNER LEG STABILIZER ADJUSTER PLATE 6 X 40 X 217 PIN TENSION STAY BEAM PIN STABILISER LEG PIN COMPR. STAY BEAM NYLON BLOCK, MAST REST THERMAL VALVE, BRACKET GUARD BATTERY BOX JACKLEG VALVE SUPPORT SUPPORT ELECTRIC SOCKET PLATE 8 X 630 X 680 TRAY WELDMENT TRACK PLATE 10 X 65 X 150 MAST VERTICAL STOP SHIM LIGHT SUPPORT, FLASHING TRACK CONTROL PANEL SEAT LYNCH PIN DIA 6 x 42 NYLOC NUT 3/8" UNC
14
MASS (Kg) 0.39 4.81 21.59 0.67 0.07 0.00 0.01 0.02
7 8 9 10 11 12 13 14 15 16 21 17 18 19 20 21 22 23 24 25 23 26 27 7
15
C
17 12 18 3 13 11 16 14
PICTORIAL VIEW
ASSEMBLY FINISH = ASSEMBLY MASS = WELDMENT FINISH = 3900.87 kg
2 8
25
10
25
25
6
NOTE: ALL DRAWING AND PARTS LIST DIMENSIONS INDICATE FINISHED SIZES. NO ALLOWANCES HAVE BEEN MADE FOR MANUFACTURING PROCESSES
K
PROJECTION
DRAWN TO AS1100 ALL DIM'S IN MM - DO NOT SCALE
NTS BS 10-8-06 -
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
SIZE
DRAWING NUMBER
REV.
300 1000 4000 1000 4000 PLUS ANGLE 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS 6 7 8
BY DATE 9 10
REVISIONS 11
BY DATE 12
SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
A0
MPL12330
SHEET 1 OF 3
13
14
10
11
12
13
14
11
21
22
25
B
9
12
13
23
18
14
18
16
17
19 20
3 15
K
PROJECTION
DRAWN TO AS1100 ALL DIM'S IN MM - DO NOT SCALE
NTS BS 10-8-06 -
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
SIZE
DRAWING NUMBER
REV.
300 1000 4000 1000 4000 PLUS ANGLE 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS 6 7 8
BY DATE 9 10
REVISIONS 11
BY DATE 12
SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
A0
MPL12330
SHEET 2 OF 3
13
14
A
17 7 15 21 20 14 11 13 16 18
19 VIEW A 23 12 25 2 22 20 19
25
5 1
10 25
PROJECTION
NTS BS 10-8-06 SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
SIZE
DRAWING NUMBER
REV.
300 1000 4000 ANGLE 1000 4000 PLUS 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS
BY DATE
A3
MPL12330
SHEET 3 OF3
Quantity DWG.1
REV 1 REV 4 4 4 4 4 4 4 8 8
Quantity
1 1 1 4 2 2 1 1 1 1 1 1 3 1 1 3 6 3
Quantity
1 2 4 1 1 2 4
Quantity
1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RBR
BALL Component
38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 14 15 16 17 18 19 20 21 22 ..PD22929PP ..PD22929PQ ..PD22929PR ..PD22929PS ..PD22929PT ..PD22929PU ..PD22929PV ..PD22929PW ..PD22929PX ..PD22929PY ..PD22929PZ ..PD22929QA ..PD22929QB ..PD22929QC ..PD22929QD ..PD22929QE ..PD22929QF ..PD22929QG ..PD22929QH ..PD22929QJ ..PD22929QK ..PD22929QL ..PD22929QM ..PD22929QP ..PD22929QR ..BE00003653 ..BE00003654 ..BE00003655 ..BE00003656 ..BE00003657 ..BE00003658 ..BE00003703 ..BE00003704 .PD22932CW .PD23767W .PM28602M85 .PM28604J30 .PM28604K25 .PM28615F38 .PM28615K44 .PM28645J .PM28645N
Description
FILTER ELEMENT SEALING WASHER O RING O RING FUEL PUMP (FEED PUMP) WASHER GASKET WATER PUMP INSERT WATER PUMP CYLINDER HEAD GASKET O RING OIL COOLER GASKET O RING O RING O RING GASKET O RING O RING CLAMP TURBO CHARGER TURBO CHARGER (RECON) TURBO OIL SUPPLY HOSE GASKET OIL FILTER RADIATOR HOSE TOP RADIATOR HOSE BOTTOM RADIATOR SUITS JOHN DEERE 6068 FAN SHROUND SUITS JOGN DEERE 6 FUEL TRANSFER PUMP SUITS JOHN FUEL HAND PRIMER PUMP SUITS JO ADAPTER FITTING KIT GASKET PUMP/HYD 25.4/10.2 CC/REV VIBRATION MOUNT 390/175kg HEX HD BOLT M16 x 85 AS1252 SKT HD CAP SCREW M10x 30 SKT HD CAP SCREW M12x 25 SKT HD CAP SCREW SKT HD CAP SCREW GR 12.9 WASHER LOAD CONVEX M10 WASHER LOAD CONVEX M20
Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 12 14 8 4 20 4
Quantity
1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 4 4 1 1 1 1 1 1 1
REV 4
Quantity
1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 5 3 10 3 5
9 10
11 12 13 14 15 16
Quantity
1 2 2 1 1 1 2 2 1 2 1 1 1 2 1 1 1 1 1 1 1 2 2 4 2 2 2 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
REV.2
REV.1 REV.2
REV.1 REV.1 REV.2 REV.1 REV.3 REV.3 REV.3 REV.3 REV.2 REV.3
27 28 1 2 3 4 5 6 7 8 9 10 11
RBR
BALL Component
12 13 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 ..PM28656D10 ..PD22873AW .PD22870AA .PD22870GY .PD22870HB .PD22870QY .PD22870RK .PD22870TP .PD22870UB .PD22981F .PD22981H .PD23752P .PD23752X .PD23753CD .PD23753CF .PD23754DM .PD23754GB .PD23778AA .PD23778Y .PD23816AZ .PD23817E .PD24435FY .PD24435GA .PD24464AJ .PD24464BB .PD24464D .PD24464ED .PD24464GX .PD24464KY .PD24464NR .PD24464PJ .PD27206A .PM26162-017 .PM28604G16 .PM28604H16 .PM28610D19 .PM28610D38 .PM28610D44 .PM28610D51 .PM28610D57 .PM28610E114 .PM28610E19 .PM28610E51 .PM28610H32 .PM28610H89 .PM28615D19 .PM28615D64 .PM28615D70 .PM28615E44 .PM28615F19 .PM28615H32 .PM28633E .PM28634D .PM28649A .PM28649B
Description
PIN SEL LOK 3 x 10 LG. STEEL BALL 4MM VALVE RELIEF CART VALVE RELIEF BODY ONLY (LESS C VALVE RELIEF CART VALVE RELIEF CART VALVE SHUTTLE 1/4" BSPP ***DO VALVE REMOTE PILOT VALVE REMOTE PILOT VALVE BALL 3/4"BSPP VALVE RESTRICTOR 1/2"BSPP GAUGE PR 600kPa 50mm 1/8"BSPT GAUGE PR (MUD) 1000PSI 2"M-1"F GAUGE PR 0-5000 psi 4"OD 1/2"N GAUGE PR 0-3000 psi 4" OD 1/2" VALVE DIVERTER 3 WAY VALVE DIR CONTROL 8 SPOOL VALVE BALL 3-WAY 1/4"NPT VALVE BALL 4-WAY LEVER DIESEL CONTROL VALVE BALL 3/8"BSPP HOSE ASSEMBLY STAUFF HOSE ASSEMBLY 2200MM VALVE BODY VALVE RELIEF CART VALVE CHECK PILOT OPEN HAND KNOB KIT "K" VALVE RELIEF CART VALVE CHECK CARTRIDGE VALVE BODY VALVE BODY VALVE SHUTTLE 1/4" BSPT O RING 17.17ID 1.78W SKT HD CAP SCREW M6x 16 SKT HD CAP SCREW M8x 16 HEX HD BOLT 1/4"UNC x 3/4" HEX HD BOLT 1/4"UNC x 1 1/2" HEX HD BOLT 1/4"UNC x 1 3/4" HEX HD BOLT 1/4"UNC x 2" HEX HD BOLT 1/4"UNC x 2 1/4" HEX HD BOLT 5/16"UNC x 4 1/2" HEX HD BOLT 5/16"UNC x 3/4" HEX HD BOLT 5/16"UNC x 2" HEX HD BOLT 1/2"UNC x 1 1/4" HEX HD BOLT 1/2"UNC x 3 1/2" SKT HD CAP SCREW SKT HD CAP SCREW SKT HD CAP SCREW SKT HD CAP SCREW SKT HD CAP SCREW SKT HD CAP SCREW GR 12.9 HEX NUT 5/16" UNC HEX NUT 1/4"UNC H.T. WASHER FLAT 1/4" (HARDENED) WASHER FLAT 5/16" (HARDENED)
Quantity
1 1 2 5 1 3 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 2 2 1 3 1 1 6 3 1 4 6 12 12 2 4 2 5 2 8 2 6 4 19 8 4 4 8 4 4 12 26 4
RBR
BALL Component
82 83 84 85 86 87 88 89 90 .PM28649E .PM28652D .PM28652E .PM28652F .PM28662G .PM28680AA .PM28680AT .PM28680X .PM28680Y
Description
WASHER FLAT 3/8" (HARDENED) WASHER HELICAL SPRING 1/4" WASHER HELICAL SPRING 5/16" WASHER HELICAL SPRING 3/8" WASHER SAFETY M6 NYLOC NUT 1/2" UNC. NYLOC NUT 3/8" UNC NYLOC NUT 1/4"UNC NYLOC NUT 5/16' UNC
Quantity
14 12 12 8 6 14 8 44 7
Quantity
1 1 1 7 1 1 1 1 3 2 1 1 2 1 1 1 1 1 1 1 0.4 M 1 1 1 2 1 1 2 2 2 2 2 2 2 4 4 34 34 4 34 4
REV 2
REV 3
REV 1
Quantity
1 1 1 4
Quantity
1 1 1 5 1 1 1 1 PR 4 1 1 1 4 1 1 1 1 1 1
REV.3
REV 1
SCALE CHECK
NONE
0.5
0.5
0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd, AND IS CONFIDENTIAL, AND MUST NOT BE MADE PUBLIC OR COPIED. THIS DRAWING IS LOANED SUBJECT TO RETURN ON DEMAND, AND IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO OUR INTERESTS.
B.S.
DRAWING NUMBER
REV.
REVISIONS
BY DATE
DATE 11-11-06
A 3 11350/41 2
SHEET 1 OF 1
Quantity
1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 4 4 4 4 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 4 2 1 1 15 5 1 3 2 1M
22 23 25 27 28 29 30 33 34 36 37 38 41
REV.2
REV.3
REV 2
43 44 46 50 50 50 50 50 51 52 53 54 60 61 63 70 80 101
REV.1
REV.1 REV 1
Quantity
1 3 3
Quantity
1 2 4 PKT 2 DRUM 20 L 3L 0.5 KG
Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 1 100
REV.2 REV 3
Quantity
1 1 1 1 1 1 1 1 1
Quantity
1 1 2 1 1 1 1 2 1 2 40 4 1 2 32 10 40 40 2 2 4 4 2 2 4 4 2 2 2 2 84 336 336 2 2 2 2 2 4 4 12 2 4 4 8 4 8 8 8 12 8 2
Quantity
1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 5 1 1 3 1 1 2 1 1 1 1 1 2 1 1 1 1 1 1 3 1 1 2 1 1 2 2 1 2 2 4 1 1 1 1 1
REV 1
REV.2
RBR
BALL Component
..PM28655H10 ..PM28655H38 ..PM28656D10 ..WU9482 ..WU9483 ..WU9484 ..WU9603 ...PD24464NP ..WU9769 .PD24464NR .PD24464GX .5-203-232 .PD23754GP .PD24464PJ .WU5077 ..PM26889CH .PD23753CD .PD23753CF .PD24435EQ .PD24435BN .WU8317 ..PD24464AJ ..PD24464AK .PD24464QD .PD23754GB .PD22921KE .PD24464MJ .WU11604 ..PD22921JE ..WU11603 .PD24464AK .PD24464KS .PD22921KD .PD24464CD .PD22921JK .PD22921KG .PD22982BJ .PD24464AU .PD24464BW .PD22870RK .PD24464DR .PD24435HQ .PD24464DE .PD24464BU .PD22870ZT .PD22921CC .PD24464AH .PD22932CW .PD24464LD .PD24464MN .PD24464MK .PD24464ML .PD24435HM .WU11462 ..PM26915RR
Description
CIRCLIP INT. DIA 10 CIRCLIP INT. DIA 38 PIN SEL LOK 3 x 10 LG. PLUNGER NEEDLE BODY NEEDLE VALVE MODIFICATION VALVE NEEDLE CARTRIDGE SUN KNOB (200D) VALVE BODY VALVE RELIEF CART VALVE PRES REDUCING (CART) VALVE DIR CONTROL 4 SPOOL VALVE BODY RESTRICTOR FIXED 0.8 x 4 HEX NIPPLE 1/4"NPT-9/16"JIC GAUGE PR 0-5000 psi 4"OD 1/2"N GAUGE PR 0-3000 psi 4" OD 1/2" PUMP HAND 3/4" VALVE CHECK 3/4"BSPP VALVE C/B ASSY (3:1 PILOT) VALVE BODY VALVE C/B CART VALVE BODY ALUMIN. (TRAV CYL 2 VALVE DIR CONTROL 8 SPOOL CYL HYD 3.5" X 1.75" X 650 STR VALVE BODY ALUMINIUM TRAVERSE CYLINDER CYLINDER HYD 3.5"x2.5"x3450mm MOUNT PLATE VALVE C/B CART VALVE FLOW FUSE CART CYL HYD 4.5" X 2" X 42" STROKE VALVE C/B CART CYL HYD 2" X 1" X 4"STROKE CYL HYD 1.5" X 7/8" X 14" STRO MOTOR HYD. SAUER DANFOSS Serie VALVE C/B CART VALVE RED/RELIEF CART VALVE SHUTTLE 1/4" BSPP ***DO VALVE BODY WITH CHECK CART MOTOR HYD 290cc VALVE BODY (WLW 650 HLDG) VALVE C/B CART SUPERSEDED BY PD22870AAF CYL HYD 2-1/2"x 1 1/2"x 203 VALVE CHECK CART PILOT OPEN PUMP/HYD 25.4/10.2 CC/REV RELIEF VALVE CART VALVE BODY VALVE MANUAL RELEASE VALVE BODY VALVE PROP FLOW CONTROL CASE DRAIN MANIFOLD HEX NIPPLE 1 1/4"NPT-1 1/4"HT
Quantity
1 1 1 1 1 1 1 1 1 6 1 2 1 3 2 2 1 1 1 1 2 2 2 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 3 1 1 1 2 1 1 5 1 1 1 1 1 1 1 1
42 44 45 46 48 49 50 51 52 53 55
REV.2
58 59 60 61 62
REV 1 REV 1
63 64 65 66 68 69 70 71 72 73 74 75 76 77 78 79 81 85 86 87 88 89 93 94
REV.2
RBR
BALL Component
..PM26944GG ..PM26944KK .WU11508 ..PM26938MM ..PM26944GG ..PM26944KK ..PM26944MM .PD22870HB .PD22870GY .PD24464E .PD22918AB .PD24435HA .WU12199 ..PM26889CH .WU5585 ..PM26884CH .WU5433 ..PM26886CH .WU5202 ..PM26884CH .PD23778Y .PD27206A .PD22918M .PD24464AJ .WU5364 ..PD24435BK .WU11460 .WU9153
Description
SOCKET 1/2"NPT SOCKET 3/4"NPT RETURN MANIFOLD SOCKET 1"BSPT SOCKET 1/2"NPT SOCKET 3/4"NPT SOCKET 1"NPT VALVE RELIEF CART VALVE RELIEF BODY ONLY (LESS C VALVE C/B DOUBLE CYLINDER ASSY 2"X1 1/4"X209 MOTOR HYD 154CC RESTRICTOR FIXED 1.8 X 4 HEX NIPPLE 1/4"NPT-9/16"JIC RESTRICTOR FIXED 0.5 x 4 HEX NIPPLE 1/4"BSPT-9/16"JIC RESTRICTOR FIXED 0.5 x 4 HEX NIPPLE 1/4"BSPP-9/16"JIC RESTRICTOR FIXED 0.75x4 HEX NIPPLE 1/4"BSPT-9/16"JIC VALVE BALL 4-WAY VALVE SHUTTLE 1/4" BSPT CYL HYD 3" x 2"x 1000 VALVE BODY VALVE CHECK MODIFIED VALVE CHECK 3/8" BSPP DRAIN-PILOT MANIFOLD SPACER TH6
Quantity
7 1 1 1 1 3 2 1 5 1 1 1 1 1 2 2 1 1 1 1 2 5 4 6 4 4 1 2
95
REV 2
98 99 101 102 105 106 107 108 109 110 111 112 113 114 115 123
REV.2
REV.3 REV.3
710-01
Parts Manual
EXPLORATION DRILL 710-01 REVISION A
Seq
1 2
Component
MPL11600-2 MPL11600/50
Item Description
MAST ASSEMBLY MAST ASSEMBLY 200DLS-50
Quantity
1 1
Quantity 1
1 1 6 1 2 1 1 1 1 1 1 2 2 0.0333 M 1 2 1 1 1 1 1 1 6 1 2 1 11 9 2 8 7 10 18 1 4 19
Quantity
1 1 6 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 11 9 2 8 7 10 18 1 4 9
710-15
Parts Manual
EXPLORATION DRILL 710-15 REVISION A
Seq
1 2
Component
MPL11615-1 MPL11615/50
Item Description
UPPER ROD SLIDE ASSEMBLY UPPER ROD SLIDE ASSY SHORT
Quantity
1 1
Quantity 1
1 1 1 1 1 2 1 1 1 1 1 2 20 2 20 2 1 20 2 20 2 2 2
Quantity
1 1 1 1 1 1 1 1 1 1 2 1 2 2 22 2 2 2 2 20 2 2 4 20 20 2
10
11
12
ITEM 1 2 3 4 5 6 QTY 1 1 1 1 1 2 1 1 1 1 1 16 4 2 2 16 2 4 16 2 16 2 2 2
13
PART No. 11608 11614 11616 11617 11619 11799 11804 12084 21411E 5303-H PD22921JK PART NAME ROLLER CARRIER ROLLER CARRIER MOUNT ROLLER ( 100 NYLON BAR ) TIE ROD RAMP SLIDE
14
MASS (Kg) -0.11 12.37 0.06 0.12 0.11 1.32 0.02 0.04 0.05 0.02 0.01 0.02 0.07 0.00 0.01 3/8" 0.00 0.00 0.01 0.00
SLEEVE (FEELED BAR 40 X 16) TIE ROD PIN ROD SLIDE KEEPER PLATE SHAFT (BMS 25 X 345) CYL HYD 2" X 1" X 4"STROKE
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PM28610F25 HEX HD BOLT 3/8" UNC X 1" PM28610H25 HEX HD BOLT 1/2"UNC x 1" PM28610H32 HEX HD BOLT 1/2"UNC X 1 1/4" PM28615F16 SKT HD CAP SCREW PM28634F PM28634H PM28634K PM28651F PM28651H PM28652F PM28652H PM28662H HEX NUT, 3/8" UNC HEX NUT 1/2"UNC H.T. HEX NUT 3/4"UNC H.T. WASHER FLAT 3/8 PLATED WASHER FLAT 1/2" PLATED HELICAL SPRING WASHER
PICTORIAL VIEW
ASSEMBLY FINISH = ASSEMBLY MASS = WELDMENT FINISH = 67.22 kg
NOTE: ALL DRAWING AND PARTS LIST DIMENSIONS INDICATE FINISHED SIZES. NO ALLOWANCES HAVE BEEN MADE FOR MANUFACTURING PROCESSES
K
PROJECTION
DRAWN TO AS1100 ALL DIM'S IN MM - DO NOT SCALE
UPPER ROD
SLIDE ASS'Y SHORT
SIZE DRAWING NUMBER REV.
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
300 1000 4000 1000 4000 PLUS ANGLE 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS 6 7 8
BY DATE 9 10
REVISIONS 11
BY DATE 12
SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
A0
MPL11615/50
SHEET 1 OF 3
13
14
10
11
12
13
14
23
24
12
21 3 10
23 3 5 13
D
19
16
D
14 22 20 17 9
2 12
21
11
E
4
19
16 18
SECTION
A-A
10
23
15
K
PROJECTION
DRAWN TO AS1100 ALL DIM'S IN MM - DO NOT SCALE
UPPER ROD
SLIDE ASS'Y SHORT
SIZE DRAWING NUMBER REV.
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
300 1000 4000 1000 4000 PLUS ANGLE 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS 6 7 8
BY DATE 9 10
REVISIONS 11
BY DATE 12
SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
A0
MPL11615/50
SHEET 2 OF 3
13
14
20 17 5 22 14
12 21 19 16
13 1 12 6 2 3 21 23 4 18 18 23 7 10 9 24 15 11
PROJECTION
1:5 YCL 29/09/09 SANDVIK MINING AND CONSTRUCTION AUSTRALIA Pty Ltd ABN 62 003 771 382
0.5 0.5
0.5 0.5
0.5 0.25
0.5 0.5
THIS DRAWING AND ALL INFORMATION THEREON IS THE CONFIDENTIAL PROPERTY OF SANDVIK MINING & CONSTRUCTION Pty Ltd. IT MUST NOT BE MADE PUBLIC OR COPIED, & MUST BE RETURNED ON DEMAND. IT IS NOT TO BE USED DIRECTLY OR INDIRECTLY IN ANY WAY DETRIMENTAL TO SANDVIK'S INTERESTS.
300 1000 4000 ANGLE 1000 4000 PLUS 2.5 1.0 0.5 3 2 1 4.0 2.5 1.5 1 0.5 0.2
DEC
0 0.0
0.00
REVISIONS
BY DATE
A3
MPL11615/50
SHEET 3 OF3
710-18
Parts Manual
EXPLORATION DRILL 710-18 REVISION A
Seq
1
Component
BE00001032 PLATFORM, MAST
Item Description
REV B
Quantity
1
REV B
REV 1 REV.2 REV.1
Quantity 1
1 1 2 1 6 8 28 14 3
710-20
Parts Manual
EXPLORATION DRILL 710-20 REVISION A
Seq
1
Component
MPL11675-1
Item Description
PLATFORM STAYROD ASSEMBLY
Quantity
1
Quantity 1
1 1 4 2 1 1 1 1 1 2 1 10 1
710-25CT
Parts Manual
EXPLORATION DRILL 710-25CT REVISION A
Seq
1 2
Component
MPL11892-2 MPL14245-1
Item Description
ROD SPIN GUARD ASSEMBLY 200DLS ROD SPIN GUARD ASSEMBLY
Quantity
1 1
Quantity 1
1 1 7 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 4 1 3 3 8 1 4
REV 1
Quantity
1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 6 1 1 1 1 1 1 2 3 12 1 2 2 3 3 2 24 9 1 2 1 12 3
710-26CT
Parts Manual
EXPLORATION DRILL 710-26CT REVISION A
Seq
1
Component
MPL14385-1
Item Description
UPPER BREAKER ASS'Y ;DE710XXCT
Quantity
1
Quantity 1
1 1 1 1 1 1 2 4 1 1 1 2 1 2 1 4 1 2 2 1 1 1 1 2 4 2 2 4 8 4 4 2 2 2 4 4 4 2 2 2 2 2 1
REV 5 REV 1
REV 1
710-76CT
Parts Manual
EXPLORATION DRILL 710-76CT REVISION A
Seq
1
Component
MPL14410-1
Item Description
BOOST PUMP ASS'Y DE710(CT)XX
Quantity
1
Quantity 1
1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 4 6 6 4 4 2 2 6 1 1 1 8 2 1 2 1 1 8 8 3 1 1 1 1 1 1 1 1 1 1 1 1 1
710-77CT
Parts Manual
EXPLORATION DRILL 710-77CT REVISION A
Seq
1
Component
MPL14400-1
Item Description
SAFT-T-SPIN ASS'Y; DE710XX(CT)
Quantity
1
Quantity 1
1 1 1 1 1 2 1 1 3 72 3 1 1 1 1 1 1 1 1 0.5 0 0 0 8 1 58 1 6 6 16 12 16 8 8 4 2 8 4 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5 6 7 8 9 10 11 12 14 15 16 17 17 17 19 20 21 22 23 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 1 3 40 41 42 43 44 45 46 47
REV.1
RBR
BALL Component
48 49 50 51 52 53 54 55 56 57 59 60 61 62 65 2 3 4 5 6 10 1 2 3 4 5 7 10 ..WU8103 ..WU8102 ..PM28604F16 ..PM28621F ..WU8044 ..WU8105A ..WU8105B ..WU8105C ..WU7820AD ..WU7820AF ..PM28604F25 ..PM28605H25 ..PM28621H ..PM26886KK ..WU9248 ...PM28604G35 .PD23801AK .PD23801AP .PD23801AL .PD22870UF .PD22871CT .HYD14405-1 ..PD23801AK ..PD23801AL ..PD23801AP ..PD23801AQ ..PD24435EB ..PD22871CT ..PD22870UF
Description
RUBBER STRIP/BACKING GUARD RUBBER SKT HD CAP SCREW M5x 16 NUT NYLOC M5 GRADE 6 HOSE CLAMP/INTERNAL SPACER TAKEUP SPACER TAKEUP SPACER TAKEUP SIGN WARNING ROT SIGN SAFE-T-SPIN LOGO. SKT HD CAP SCREW M5x 25 SKT HD C'SUNK SCREW M8x 25 NUT NYLOC M8 GRADE 6 HEX NIPPLE 3/4"BSPP-3/4"JIC LOCKING SCREW SKT HD CAP SCREW M6x 35 QUICK DISCONNECT 3/4"BSPP FEMA QUICK DISCONNECT 3/8"BSPP FEMA QUICK DISCONNECT 3/4" BSPP MAL VALVE REMOTE PILOT VALVE ASSEMBLY 1 SPOOL HYD CIRCUIT SAFE-T-SPIN;REF QUICK DISCONNECT 3/4"BSPP FEMA QUICK DISCONNECT 3/4" BSPP MAL QUICK DISCONNECT 3/8"BSPP FEMA QUICK DISCONNECT 3/8"BSPP MALE MOTOR HYD 400cc VALVE ASSEMBLY 1 SPOOL VALVE REMOTE PILOT REV.3 REV.2
Quantity
2 2 8 12 2 0 2 0 1 1 4 4 4 2 3 3 1 1 1 1 1 1 2 2 1 1 1 1 1
REV.2
710-78
Parts Manual
EXPLORATION DRILL 710-78 REVISION A
Seq
1
Component
MPL13905-1
Item Description
SUPPORT STRUCTURE SAFE-T-SPIN
Quantity
1
Quantity 1
1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 6 14 2 4 4 1 4 6 2 6 1 2 16 2
710-79
Parts Manual
EXPLORATION DRILL 710-79 REVISION A
Seq
1
Component
BE00002540 ASS'Y, DE710,
Item Description
REV A
Quantity
1
REV A
Quantity 1
1 1 1 1 2 2 4 4 4 2 2 2 4 2 2 2 1 1 1 1 2 1 1 1 2 2 4 2 2 2 2 1 2 4 4 2 1 1 1 1 1 1 1 1 1 1 1 1 5 2 2 5 4 3
REV.2
REV A REV 2
RBR
BALL Component
18 19 6 7 8 9 10 11 12 13 14 15 16 17 18 ..PM28652H ..PM28680AA .BE00002551 .PD24406BC .PM28603J25 .PM28603K40 .PM28610H38 .PM28615D19 .PM28615F32 .PM28648J .PM28648K .PM28652D .PM28652F .PM28652H .PM28656G40
Description
WASHER HELICAL SPRING 1/2" NYLOC NUT 1/2" UNC. EXTENSION SHAFT, SPOOLER FELT SEAL AND COVER HEX HD BOLT M10x 25 GR 8.8 HEX HD BOLT M12x 40 GR 8.8 HEX HD BOLT 1/2"UNC x 1 1/2" SKT HD CAP SCREW SKT HD CAP SCREW WASHER HELICAL SPRING M10 WASHER HELICAL SPRING M12 WASHER HELICAL SPRING 1/4" WASHER HELICAL SPRING 3/8" WASHER HELICAL SPRING 1/2" PIN SEL LOK 5 x 40 LG.
Quantity
9 4 1 1 4 8 2 1 1 4 8 2 1 2 1
SANDVIK A SE-811 81 SANDVIKEN SWEDEN TEL +46 (0)26 26 00 00 FAX +64 (0)26 26 10 22 www.sandvik .com