Professional Documents
Culture Documents
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
A General requirements
ASTM A325 or A490 bolts are used for primary structural connections. 12-SAMSS-008
A1
(PIP STS05130, Para. 6.5.1) Sec. I
The minimum size of ASTM A325 N bolts shall be 20 mm.7.1.8.4 The 12-SAMSS-007
A2
minimum size of high-strength bolts shall be 20 mm diameter. Para. 6.2.5.3
Joint type of the connection has been identified on the drawing or was
specified in the design, ie: snug-tightened joint, pretensioned joint or slip-
critical joint. 12-SAMSS-007
A4
NOTE: Indicate joint type: _______________________ Sec. 3.2
(AISC, Specification for Structural Joints Using ASTM A325 or A490
Bolts, Sec. 4)
All bolts, nuts, and washers shall be properly identified and marked with 12-SAMSS-007
A6
the material grade and manufacturer's logo. Para. 6.2.5.5
All bolt holes shall be standard holes with a diameter 1/16 inch (1 mm)
12-SAMSS-007
A7 larger than the nominal bolt diameter.
Para. 6.2.5.11
Refer to Table 4.1 attached, for the standard hole dimensions.
Bolts have full thread engement with the nut. The bolt length used shall
be such that the end of the bolt extends beyond or is at least flush with
12-SAMSS-007
A10 the outer face of the nut when properly installed.
Sec. 3.2
(AISC, Specification for Structural Joints Using ASTM A325 or A490
Bolts, Para. 2.3.2)
Page 1 of 5
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
High Strength Bolts Tightening Inspection and Testing
SAIC-M-1072 18-May-05 Civil
(ASTM A325 or A490 Bolts)
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
All nuts for high-strength bolts shall be wax-dipped to reduce torque 12-SAMSS-007
A11
during installation Para. 6.2.5.22
Mechanically galvanized bolts and nuts shall not be intermixed with hot- 12-SAMSS-008
A12
dip galvanized nuts and bolts. (PIP STS05130, Para. 6.5.4) Sec. I
ASTM A490/A490M bolts and galvanized ASTM A325/A325M bolts shall 12-SAMSS-008
A13
not be reused. (PIP STS05130, Para. 6.5.6) Sec. I
The erector shall color code, die punch, or otherwise mark the ends of
12-SAMSS-008
A14 torqued bolts indicating that the bolts have been properly tensioned and
Sec. I
are ready for inspection. (PIP STS05130, Para. 6.5.7)
Faying surfaces and surfaces adjacent to the bolt head and nut for snug-
tightened or pretensioned joints shall be free of dirt and other foreign
12-SAMSS-007
A15 material. These joints may be coated or uncoated.
Sec. 3.2
(AISC, Specification for Structural Joints Using ASTM A325 or A490
Bolts, Para. 3.2.1 & PIP STS05130, Para. 6.5.1)
An ASTM F436 beveled washer shall be installed when the outer face of
the joint has a slope that is greater than 1:20. 12-SAMSS-007
A17
(AISC, Specification for Structural Joints Using ASTM A325 or A490 Sec. 3.2
Bolts, Para. 3.2.1 & PIP STS05130, Para. 6.5.1)
B Snug-tightening Method
All bolt holes are aligned and permit insertion of bolts without damage to
12-SAMSS-007
B1 the threads. (AISC, Specification for Structural Joints Using ASTM A325
Sec. 3.2
or A490 Bolts, Para. 8.1)
Normal washers are installed on slotted holes (Washers are not required
12-SAMSS-007
B2 on standard bolt holes). (AISC, Specification for Structural Joints Using
Sec. 3.2
ASTM A325 or A490 Bolts, Para. 8.1)
Page 2 of 5
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
High Strength Bolts Tightening Inspection and Testing
SAIC-M-1072 18-May-05 Civil
(ASTM A325 or A490 Bolts)
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
The faying surfaces are in firm contact (snug-tight condition) after a few
impacts of an impact wrench or with the full effort of a worker using a 12-SAMSS-007
B5
spud wrench. (AISC' Specification for Structural Joints Using ASTM Sec. 3.2
A325 or A490 Bolts, Para. 8.1)
The erector shall color code, die punch, or otherwise mark the ends of
12-SAMSS-008
B6 torqued bolts indicating that the bolts have been properly tensioned and
Sec. I
are ready for inspection. (PIP STS05130, Para. 6.5.7)
The nut and protruding end of the bolt are match-marked after snug-
tightening is performed. 12-SAMSS-007
C4
(AISC, Specification for Structural Joints Using ASTM A325 or A490 Sec. 3.2
Bolts, Para. 9.2.1 and 8.2.1-Commentary)
After all bolts are in snug-tight condition and matched-marked, the nut or
bolt head is rotated to the amount of turn specified in Table 8.2 in 12-SAMSS-007
C5
Attachment 4 of this checklist. (AISC, Specification for Structural Joints Sec. 3.2
Using ASTM A325 or A490 Bolts, Para. 8.2.1)
Page 3 of 5
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
High Strength Bolts Tightening Inspection and Testing
SAIC-M-1072 18-May-05 Civil
(ASTM A325 or A490 Bolts)
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
The erector shall color code, die punch, or otherwise mark the ends of
12-SAMSS-008
D6 torqued bolts indicating that the bolts have been properly tensioned and
Sec. I
are ready for inspection. (PIP STS05130, Para. 6.5.7)
Direct tension indicator materials have been inspected per the checklist,
12-SAMSS-007
E1 SAIC-M-2021. (AISC, Specification for Structural Joints Using ASTM
Sec. 3.2
A325 or A490 Bolts, Para. 8.2.4)
Page 4 of 5
SAUDI ARAMCO ID/PID - 18-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
High Strength Bolts Tightening Inspection and Testing
SAIC-M-1072 18-May-05 Civil
(ASTM A325 or A490 Bolts)
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
The erector shall color code, die punch, or otherwise mark the ends of
12-SAMSS-008
E6 torqued bolts indicating that the bolts have been properly tensioned and
Sec. I
are ready for inspection. (PIP STS05130, Para. 6.5.7)
REMARKS:
REFERENCE DOCUMENTS:
1- SAES-M-001 -- Structural Design Criteria for Non-Building Structures, 30 June 2004
2- 12-SAMSS-008 -- Erection of Structural and Miscellaneous Steel, 28 January 2004
Page 5 of 5