Professional Documents
Culture Documents
--
1)
Operating states
On/off status message, storage spring, tripped, readiness
Switching position (connected, test and disconnected position, not present) for withdrawable circuit
breakers,
PROFIBUS/MODBUS write protection on/off, free user input
--
1)
--
1)
Control commands
Switch circuit breakers ON/OFF, switch free user output ON/OFF
Reset tripped signal
Delete event and history memory
Rest min./max. measured values, reset maintenance information
--
1)
--
1)
History
Read out the event protocol, read out the release protocol --
1)
Information on maintenance
Number of tripping operations - L, S/I and total, contact erosion
Number of switching operations - under load and total, operating hours
--
1)
Event signals
Tripped signals with data on tripping currents
Alarmsignals (e. g. overload) with incoming/outgoing information
All named event signals with time stamp
--
1)
--
1)
2)
2)
2)
2)
Measured values
Phase currents, each with min./max. value
Temperature in the circuit breaker with min./max. value
Temperature in the control cabinet with min./max. value
All named measured values with time stamp
--
1)
--
1)
--
1)
Siemens AG 2011
3WL Air Circuit Breakers
23
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
CubicleBUS modules
Digital output modules with rotary coding switch
6 items of binary information concerning the state of the circuit
breaker (reasons for tripping and warnings) can be output via
this module to external signaling devices (e. g. light, horn) or be
used for the selective shut-down of other system components
(e. g. frequency converters).
Digital output modules are available in versions with and without
a rotary coding switch. On modules with a rotary coding switch
it is possible to choose between two signaling blocks each with
6 defined assignments and to set an additional response delay.
All the digital output modules are available as a version with re-
lay outputs (CO contacts, up to 12 A). Up to two modules of this
type can be connected to one 3WL circuit breaker.
Digital output modules with rotary coding switch
Digital output modules, configurable
The configurable output module is available for higher-perfor-
mance solutions. With this module, random events on the
CubicleBUS can be switched directly to one of six available out-
puts or three of these outputs can be assigned with up to six
events. In other words, up to six events can be placed on one
physical output with "OR" operation. Either BDA/BDA Plus or
Switch ES Power is used for configuring.
A relay variant is also available here the same as for the output
modules with rotary coding switch. Only one module of this type
is possible per 3WL circuit breaker.
Digital output modules, configurable
Analog output modules
The analog output module can be used to output the following
measured values to analog indicators in the control cabinet
door:
I
L1
, I
L2
, I
L3
, I
N
or
U
L12
, U
L23
, U
L31
, U
L1N
or
P
L1
, P
L2
, P
L3
, S
tot
or
p.f.
1
, p.f.
2
, p.f.
3
, I % or
f
avg
, U
LLavg
, P
tot
, p.f.
avg
Four 4-20-mA/0-10-V interfaces are available for this. The mea-
sured values to be output are selected with a rotary coding
switch. By using the analog output module it is possible to do
without additional converters and their conventional installa-
tion/wiring in the main current path. Up to two modules of this
type can be connected to one 3WL circuit breaker.
Analog output modules
Digital input module
With the digital input module, up to 6 additional binary signals
(24 V DC) in the circuit breaker environment can be connected
to the system. It is thus possible for example to send messages
concerning the state of a switch disconnector or a control cabi-
net door to the PROFIBUS DP/MODBUS.
With the digital input module on the CubicleBUS it is also possi-
ble for the two different protection parameter sets held in the
ETU76B electronic releases to be switched over automatically in
a few milliseconds. It is thus possible, for example, to automati-
cally change the parameters of a coupling switch should the
transformer infeed fail.
One module each of this type can be used for holding the six
items of digital information and for automatically switching over
the parameters.
Digital input module
ZSI modules (short-time grading control)
The use of ZSI modules is recommended when Siemens circuit
breakers are arranged in several staggered levels but full grad-
ing with the smallest possible delay is to be assured neverthe-
less.
The circuit breakers are interconnected by these modules. In
case of a short-circuit, each affected circuit breaker asks the cir-
cuit breakers directly downstream whether the short-circuit has
also occurred in the next, lower level. The short-circuit is exactly
localized as the result, and only the next upstream circuit
breaker in the energy flow direction is switched off.
ZSI modules (short-time grading control)
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
24
Siemens 2012
Technical specifications
Switching capacity
1)
Size II with I
n max
2500 A.
2)
Size II with I
n max
= 3200 A and I
n max
= 4000 A.
3)
At a rated voltage of 690 V the I
cw
value of the circuit breaker cannot be
greater than the I
cu
or I
cs
value at 690 V.
4)
Rated operational voltage U
e
= 1150 V.
5)
At U
e
= 220 V DC.
L, S, I, N, G: Designation according to IEC 60947-2, Appendix K.
6)
At U
e
= 300 V DC.
7)
At U
e
= 600 V DC.
8)
At U
e
= 1000 V DC.
9)
Values also apply to version 690 V + 20 % with Z option "A16".
Sizes I II III
Type 3WL11 3WL12 3WL13
Switching capacity class N
S H
N S H
H
C
3-pole
C
4-pole
Short-circuit breaking capacity
Rated operational voltage U
e
up to 415 V AC
I
cu
kA 55 66 85 66 80 100 100 150 130
I
cs
kA 55 66 85 66 80 100 100 150 130
I
cm
kA 121 145 187 145 176 220 220 330 286
Rated operational voltage U
e
up to 500 V AC
I
cu
kA 55 66 85 66 80 100 100 150 130
I
cs
kA 55 66 85 66 80 100 100 150 130
I
cm
kA 121 145 187 145 176 220 220 330 286
Rated operational voltage U
e
up to 690 V AC
I
cu
kA 42 50 66 50 75 85 85 150 130
I
cs
kA 42 50 66 50 75 85 85 150 130
I
cm
kA 88 105 145 105 165 187 187 330 286
Rated operational voltage U
e
up to 1000 V/1150 V AC
I
cu
kA -- -- 50
9)
-- -- 50 50 70
4)
70
4)
I
cs
kA -- -- 50
9)
-- -- 50 50 70
4)
70
4)
I
cm
kA -- -- 105
9)
-- -- 105 105 154
4)
154
4)
Rated short-time withstand current I
cw
of the circuit breakers
3)
0.5 s kA 55 66 75 66 80 100 100 100 100
1 s kA 42 50 66 55 66 80 100 100 100
2 s kA 29.5 35 46 39 46 65
1)
/70
2)
80 80 80
3 s kA 24 29 37 32 44 50
1)
/65
2)
65 65 65
Short-circuit breaking capacity I
cc
of the non-automatic air circuit breakers
Up to 500 V AC kA 55 66 75 66 80 100 100 100 100
Up to 690 V AC kA 42 50 66 50 75 85 85 100 100
Up to 1000 V /1150 V AC kA -- -- 50
9)
-- -- 50
4)
50
4)
70
4)
70
4)
Sizes II
Type 3WL12
Switching capacity class DC
Short-circuit breaking capacity
Up to 220 V DC
Up to 300 V DC
Up to 600 V DC
Up to 1000 V DC
I
cc
I
cc
I
cc
I
cc
kA
kA
kA
kA
35
30
25
20
Rated short-time withstand current I
cw
0.5 s
1 s
2 s
3 s
kA
kA
kA
kA
--
35
5)
/30
6)
/25
7)
/20
8)
--
--
N S H N S H H C C
DC
Circuit breaker with ECO switching capacity N
Circuit breaker with standard switching capacity S
Circuit breaker with high switching capacity H
Circuit breakers with very high switching capacity C
Non-automatic air circuit breakers with DC switching ca-
pacity
These switching capacities are indicated in the corre-
sponding tables by the symbols shown on orange back-
grounds.
N
S
H
C
DC
Abbreviations
(functions)
L = Long Time Delay = Overload protection
S = Short Time Delay = Short-circuit protection
(short-time delayed)
I = Instantaneous = Short-circuit protection
(instantaneous)
N = Neutral Protection Neutral conductor protec-
tion
G = Ground Fault Ground-fault protection
Siemens AG 2011
3WL Air Circuit Breakers
25
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
1)
Opening time on instantaneous short-circuit release with
ETU15B = 85 ms.
2)
Make-time through closing solenoid for synchronization purposes
(short-time excited) 50 ms.
3)
Maintenance means: replace main contact elements and arc chutes (see
Operating Manual).
4)
Use of releases from 20 C
5)
ETU76B with graphics display can be used up to max. 55 C.
6)
Minimum interval between 2 switching operations.
7)
3-pole switching with switching capacity N and S: 45/h.
8)
For switching capacity H: 1600 A to 70 C.
9)
The main contacts of size I circuit breakers with switching capacity H can
only be replaced at the factory.
Sizes I II
Type ... 3WL11 10 3WL11 12 3WL11 16 3WL11 20 3WL12 08 3WL12 10 3WL12 12 3WL12 16
Rated current I
n
at 40 C, at 50/60 Hz
Main conductors
N conductor (only on 4-pole versions)
A
A
... 1000
... 1000
1250
1250
1600
1600
2000
2000
800
800
1000
1000
1250
1250
1600
1600
Rated operational voltage U
e
at 50/60 Hz
(1000 V version, see Catalog LV 10.1, "Options")
V AC ...
690/1000
...
690/1000
...
690/1000
...
690/1000
...
690/1000
...
690/1000
...
690/1000
...
690/1000
Rated insulation voltage U
i
V AC 1000 1000 1000 1000 1000 1000 1000 1000
Rated impulse withstand voltage U
imp
Main current paths
Auxiliary circuits
Control circuits
kV
kV
kV
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
Isolating function to EN 60 947-2 Yes Yes Yes Yes Yes Yes Yes Yes
Utilization category B
Permissible ambient temperature
During operation (in operation with LCD max. 55 C)
4)
During storage (special conditions for LCDs must be
observed)
C
C
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
Permissible load
At rear horizontal main con-
nections
Up to 55 C (Cu bare)
Up to 60 C (Cu bare)
5)
Up to 70 C (Cu black
painted)
5)
A
A
A
1000
1000
1000
1250
1250
1210
1600
1600
1490
8)
2000
1930
1780
800
800
800
1000
1000
1000
1250
1250
1250
1600
1600
1600
Rated rotor operational voltage U
er
V 2000 2000 2000 2000 2000 2000 2000 2000
Power loss at I
n
with 3-phase symmetrical load
Fixed-mounted circuit breakers
Withdrawable circuit breakers
W
W
100
195
105
205
150
350
240
440
40
85
45
95
80
165
85
175
Switching times
Make-time
Opening time
Electrical make-time (through closing solenoid)
2)
Electrical opening time (through shunt release)
Electrical opening time (instantaneous undervoltage
release)
Opening time due to ETU, instantaneous short-circuit
release
ms
ms
ms
ms
ms
ms
35
38
80
73
73
50
1)
35
38
80
73
73
50
1)
35
38
80
73
73
50
1)
35
38
80
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
Endurance: Switching capacity N and S. 3/4-pole
Mechanical (without maintenance) Operating cycles
Mechanical (with maintenance)
3)
Operating cycles
Electrical (without maintenance) Operating cycles
1000 V version, electrical Operating cycles
(without maintenance)
1150 V version, electrical Operating cycles
(without maintenance)
Electrical (with maintenance)
3)
Operating cycles
10 000
20 000
10 000
--
--
20 000
10 000
20 000
10 000
--
--
20 000
10 000
20 000
10 000
--
--
20 000
10 000
15 000
7500
1000
--
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
Endurance: Switching capacity H, 3-pole
Mechanical (without maintenance) Operating cycles
Mechanical (with maintenance)
3)
Operating cycles
Electrical (without maintenance) Operating cycles
1000 V version, electrical Operating cycles
(without maintenance)
1150 V version, electrical Operating cycles
(without maintenance)
Electrical (with maintenance)
3)9)
Operating cycles
10 000
15 000
7 500
1000
--
15 000
10 000
15 000
7 500
1000
--
15 000
10 000
15 000
7 500
1000
--
15 000
10 000
15 000
7500
1000
--
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
Endurance: Switching capacity H, 4-pole
Mechanical (without maintenance) Operating cycles
Mechanical (with maintenance)
3)
Operating cycles
Electrical (without maintenance) Operating cycles
1000 V version, electrical Operating cycles
(without maintenance)
1150 V version, electrical Operating cycles
(without maintenance)
Electrical (with maintenance)
3)9)
Operating cycles
10 000
15 000
7 500
1000
--
10 000
10 000
15 000
7 500
1000
--
10 000
10 000
15 000
7 500
1000
--
10 000
10 000
15 000
7500
1000
--
10 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
10 000
15 000
7500
1000
500
15 000
Switching frequency
6)
690 V version
1000 V version
1150 V version
1/h
1/h
1/h
60
7)
--
--
60
7)
--
--
60
7)
--
--
60
20
--
60
7)
20
20
60
7)
20
20
60
7)
20
20
60
7)
20
20
Minimum interval between tripping operation by elec-
tronic release and next making operation of the circuit
breaker (only with autom. mechanical resetting of the
lockout device).
Minimum interval between ON/OFF or OFF/ON switching
operations.
ms 80 80 80 80 80 80 80 80
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
26
Siemens 2012
Sizes I II
Type ... 3WL11 10 3WL11 12 3WL11 16 3WL11 20 3WL12 08 3WL12 10 3WL12 12 3WL12 16
Mounting position
and/or
Degree of protection IP20 without cabinet door, IP41 with door sealing frame, IP55 with cover
Main conductor
minimum
cross-sections
Copper bars,
bare
Copper bars,
painted black
Unit(s)
mm
2
Unit(s)
mm
2
1
60 10
1
60 10
2
40 10
2
40 10
2
50 10
2
50 10
3
50 10
3
50 10
1
50 10
1
50 10
1
60 10
1
60 10
2
40 10
2
40 10
2
50 10
2
50 10
Auxiliary conductors (Cu)
Max. number of
auxiliary conductors cross-
section
(solid/stranded)
Standard connection = strain-
relief clamp
Without end sleeve
With end sleeve according to
DIN 46228 Part 2
With twin end sleeve
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16); 1 2.5 mm
2
(AWG 14)
1 0.5 mm
2
(AWG 20) ... 1 1.5 mm
2
(AWG 16)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Optional connection = tension
spring
Without end sleeve
With end sleeve according to
DIN 46228 Part 2
2 0.5 mm
2
(AWG 20) ... 2 2.5 mm
2
(AWG 14)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Position signaling switches Tension spring terminals 1 0.5 mm
2
(AWG 20) ... 1 2.5 mm
2
(AWG 14)
Weights 3-pole
4-pole
Fixed-mounted CBs
Withdrawable CBs
Guide frames
Fixed-mounted CBs
Withdrawable CBs
Guide frames
kg
kg
kg
kg
kg
kg
43
45
25
50
54
30
43
45
25
50
54
30
43
45
25
50
54
30
43
45
25
50
54
30
56
60
31
67
72
37
56
60
31
67
72
37
56
60
31
67
72
37
56
60
31
67
72
37
NSE0_00061 a
30 30
NSE0_00062a
30 30
NSE0_00927a
h
=
m
m
m
a
x
.
Siemens AG 2011
3WL Air Circuit Breakers
27
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
1)
Opening time on instantaneous short-circuit release with
ETU15B = 85 ms.
2)
Make-time through closing solenoid for synchronization purposes
(short-time excited) 50 ms.
3)
Maintenance means: replace main contact elements and arc chutes
(see Operating Manual).
4)
Use of releases from 20 C
5)
ETU76B with graphics display can be used up to max. 55 C.
6)
4000 A, size II in fixed-mounted version, 3-pole.
7)
Size II with order code "A15" and size III:
Data for very high switching capacity.
8)
Minimum interval between 2 switching operations.
9)
3-pole switching with switching capacity N and S: 45/h.
Sizes II III
Type 3WL12 20 3WL12 25 3WL12 32 3WL12 40 3WL13 40 3WL13 50 3WL13 63
Rated current I
n
at 40 C, at 50/60 Hz
Main conductors
N conductor (only on 4-pole versions)
A
A
2000
2000
2500
2500
3200
3200
4000
4000
4000
4000
5000
5000
6300
6300
Rated operational voltage U
e
at 50/60 Hz
(1000 V version, see Catalog LV 10.1, "Options")
V AC ...
690/1000
...
690/1000
...
690/1000
... 690 ...
690/1000
...
690/1000
...
690/1000
Rated insulation voltage U
i
V AC 1000 1000 1000 1000 1000 1000 1000
Rated impulse withstand voltage U
imp
Main current paths
Auxiliary circuits
Control circuits
kV
kV
kV
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
12
4
2.5
Isolating function to EN 60947-2 Yes Yes Yes Yes Yes Yes Yes
Utilization category B (except switching capacity class DC)
Permissible ambient temperature
During operation (in operation with LCD max. 55 C)
4)
During storage (special conditions for LCDs must be observed)
C
C
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
Permissible load
6)
Up to 55 C (Cu bare)
Up to 60 C (Cu bare)
5)
Up to 70 C (Cu black painted)
5)
A
A
A
2000
2000
2000
2500
2500
2280
3200
3020
2870
3950
3810
3600
4000
4000
4000
5000
5000
5000
5920
5810
5500
Rated rotor operational voltage U
er
V 2000 2000 2000 2000 2000 2000 2000
Power loss at I
n
with 3-phase symmetrical load
Fixed-mounted circuit breakers
Withdrawable circuit breakers
W
W
180
320
270
520
410
710
750
925
520
810
630
1050
900
1600
Switching times
Make-time
Opening time
Electrical make-time (through closing solenoid)
2)
Electrical opening time (through shunt release)
Electrical opening time (instantaneous undervoltage release)
Opening time due to ETU, instantaneous short-circuit release
ms
ms
ms
ms
ms
ms
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
1)
35
34
100
73
73
50
35
34
100
73
73
50
35
34
100
73
73
50
Endurance
Mechanical (without maintenance) Operating cycles
Mechanical (with maintenance)
3)
Operating cycles
Electrical (without maintenance) up to 690 V Operating cycles
1000 V version, electrical (without maintenance) Operating cycles
1150 V version, electrical
7)
(without maintenance) Operating cycles
Switching capacity C: Electrical Operating cycles
(without maintenance) up to 690 V
Switching capacity C: Electrical Operating cycles
(without maintenance) up to 1150 V
Electrical (with maintenance)
3)
Operating cycles
10000
15000
7500
1000
500
--
--
15000
10000
15000
7500
1000
500
--
--
15000
10000
15000
4000
1000
500
--
--
15000
10000
15000
2000
1000
500
--
--
15000
5000
10000
2000
1000
500
1000
500
10000
5000
10000
2000
1000
500
1000
500
10000
5000
10000
2000
1000
500
1000
500
10000
Switching frequency
8)
690 V version
1000 V version
1150 V version
7)
1/h
1/h
1/h
60
9)
20
20
60
9)
20
20
60
9)
20
20
60
9)
20
20
60
20
20
60
20
20
60
20
20
Minimum interval between tripping operation by electronic
release and next making operation of the
circuit breaker (only with automatic
mechanical resetting of the lockout device)
Minimum interval between ON/OFF or OFF/ON switching opera-
tions.
ms 80 80 80 80 80 80 80
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
28
Siemens 2012
1)
Minimum main conductor cross-sections for 4-pole withdrawable circuit
breakers: 4 x 120 x 10 mm
Sizes II III
Type 3WL12 20 3WL12 25 3WL12 32 3WL12 40 3WL13 40 3WL13 50 3WL13 63
Mounting position
Degree of protection IP20 without cabinet door, IP41 with door sealing frame, IP55 with cover
Main conductor
minimum
cross-sections
Copper bars,
bare
Copper bars,
painted black
Unit(s)
mm
2
Unit(s)
mm
2
3
50 10
3
50 10
2
100 10
2
100 10
3
100 10
3
100 10
4
120 10
4
100 10
1)
4 x
100 x 10
4
100 10
6 x
100 x 10
6
100 10
6 x
120 x 10
6
120 10
Auxiliary conductors
(Cu)
Max. no. of
auxiliary conductors
cross-section
(solid/stranded)
Standard connection = strain-relief clamp
Without end sleeve
With end sleeve according to
DIN 46228 Part 2
With twin end sleeve
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16); 1 2.5 mm
2
(AWG 14)
1 0.5 mm
2
(AWG 20) ... 1 1.5 mm
2
(AWG 16)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Optional connection = tension spring
Without end sleeve
With end sleeve according to
DIN 46228 Part 2
2 0.5 mm
2
(AWG 20) ... 2 2.5 mm
2
(AWG 14)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Position signaling
switches
Tension spring terminals 1 0.5 mm
2
(AWG 20) ... 1 2.5 mm
2
(AWG 14)
Weights 3-pole
4-pole
Fixed-mounted circuit breakers
Withdrawable circuit breakers
Guide frames
Fixed-mounted circuit breakers
Withdrawable circuit breakers
Guide frames
kg
kg
kg
kg
kg
kg
56
60
31
67
72
37
59
63
39
71
76
47
64
68
45
77
82
54
85
121
52
103
146
62
82
88
60
99
106
84
82
88
60
99
106
84
90
96
70
108
108
119
NSE0_00061 a
30 30
NSE0_00062a
30 30
and/
or
NSE0_00927a
h
=
m
m
m
a
x
.
Siemens AG 2011
3WL Air Circuit Breakers
29
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
1)
24 V and 30 V only with undervoltage release UVR (F3).
Sizes I to III
Type 3WL1
Manual operating mechanism with mechanical closing
Closing/
Charging stored-
energy feature
Max. force required to operate the hand lever
Required number of strokes on the hand lever
N 230
9
Manual operating mechanism with mechanical and electrical closing
Charging stored-
energy feature
Closing solenoid
(CC)
Primary operating range 0.85 ... 1.1 U
s
Extended operating range for battery operation At 24 V DC, 48 V DC
60 V DC, 110 V DC
220 V DC
0.7 ... 1.26 U
s
Rated control supply voltage U
s
50/60 Hz AC
DC
V
V
110 ... 127; 208 ... 240
24; 30; 48; 60; 110 ... 125; 220 ... 250
Power consumption AC/DC VA/W 15/15
Minimum command duration at U
s
for the closing solenoid ms 60
Short-circuit protection
Smallest permissible DIAZED fuse (gL operational class)/
miniature circuit breaker with C characteristic
1 A TDz (slow)/1 A
Manual/motorized operating mechanism with mechanical and electrical closing
Manual operating
mechanism
For data see above.
Motor Primary operating range 0.85 ... 1.1 U
s
Extended operating range for battery operation At 24 V DC, 48 V DC
60 V DC, 110 V DC
220 V DC
0.7 ... 1.26 U
s
Power consumption of motor AC/DC VA/W 135/135
Time required to charge the stored-energy mechanism at 1 U
s
s 10
Closing solenoid For data see above.
For motor and
closing solenoid
Short-circuit protection
Smallest permissible DIAZED fuse (gL operational class)/miniature circuit breaker with
C characteristic; Motor and closing solenoid for identical rated control supply voltages
6 A TDz (slow)/2 A
Smallest permissible DIAZED fuse (gL operational class)/
miniature circuit breaker with C characteristic (for different
rated control supply voltages)
At U
s
= 24 ... 30 V
At U
s
= 48 ... 60 V
At U
s
= 110 ... 125 V DC/
110 ... 127 V AC
At U
s
= 220 ... 250 V DC/
208 ... 240 V AC
6 A
6 A
2 A
2 A
Electronic release signals
Measuring accuracy of the electronic release Protection functions acc. to
EN 60947; current indication 10 %;
Measurement function
Base electrical quantities 1 %;
Measurement function
derived variables 4 %
Auxiliary releases
Undervoltage
releases
UVR (F3) and
UVR-t
d
(F4)
Response values Pick-up
Dropout
0.85 U
s
(circuit breaker can
be closed)
0.35 ... 0.7 U
s
(circuit breaker is tripped)
Primary operating range 0.85 ... 1.1
Extended operating range for battery operation At 24 V DC, 30 V DC,
48 V DC, 110 V DC, 220 V DC
0.85 ... 1.26
Rated control supply voltage U
s
Instantaneous
50/60 Hz AC
DC
Delayed
50/60 Hz AC
DC
V
V
V
V
110 ... 127/208 ... 240/380 ... 415
24/30/48/60/110 ... 125/220 ... 250
1)
110 ... 127; 208 ... 240; 380 ... 415
48; 110 ... 125; 220 ... 250
Power consumption (pickup/uninterrupted duty) AC
DC
VA
W
20/5
20/5
Opening time of circuit breaker at U
s
= 0 ms 200
- Version UVR (F3)
Instantaneous
With delay
ms
ms
80
200
- Version UVR-t
d
(F8)
with delay, t
d
= 0.2 to 3.2 s
Reset via additional NC contact direct switching off
s
ms
0.2 ... 3.2
100
Short-circuit protection
Smallest permissible DIAZED fuse (gL operational class)/
miniature circuit breaker with C characteristic
1 A TDz (slow)/1 A
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
30
Siemens 2012
Sizes I to III
Type 3WL1
Auxiliary releases
Shunt release (ST)
(F1, F2)
For continuous command
(100 % ON period), locks
out on momentary-con-
tact commands
- Response value Pick-up > 0.7 U
s
(circuit breaker is tripped)
- Primary operating range 0.85 ... 1.1 U
s
- Extended operating range
for battery operation
At 24 V DC, 48 V DC
60 V DC, 110 V DC
220 V DC
0.7 ... 1.26 U
s
- Rated control supply voltage U
s
50/60 Hz AC
DC
V
V
110 ... 127; 208 ... 240
24; 30; 48; 60; 110 ... 125;
220 ... 250
- Power consumption AC/DC VA/W 15/15
- Minimum command duration at U
s
ms 60
- Opening time of circuit breaker at
U
s
= 100 %
AC/DC ms 80
- Short-circuit protection
Smallest permissible DIAZED fuse (gL operational
class)/miniature circuit breaker with C characteristic
1 A TDz (slow)/1 A
5 % OP - Response value Pick-up > 0.7 U
s
(circuit breaker is tripped)
- Primary operating range 0.85 ... 1.1 U
s
- Extended operating range
for battery operation
At 24 V DC, 48 V DC
60 V DC, 110 V DC
220 V DC
0.7 ... 1.26 U
s
- Rated control supply voltage U
s
50/60 Hz AC
DC
V
V
110 ... 127; 208 ... 240
24; 48; 110 ... 125; 220 ... 250
- Power consumption AC/DC VA/W 15/15
- Minimum command duration at U
s
ms 25
- Opening time of circuit breaker at
U
s
= 100 %
AC/DC ms 50
- Short-circuit protection
Smallest permissible DIAZED fuse (gL operational
class)/miniature circuit breaker with C characteristic
1 A TDz (slow)/1 A
With stored energy fea-
ture
consisting of shunt re-
lease and capacitor stor-
age device
- Rated control supply voltage U
s
50/60 Hz AC
DC
V
V
110; 230
110; 220
- Primary operating range 0.85 ... 1.1 U
s
- Power consumption AC/DC VA/W 1/1
- Storage time at U
s
/
recharging time at U
s
max. 5 min/min. 5 s
- Opening time of circuit breaker, short-circuit protec-
tion
As with "for continuous com-
mand"
Remote reset solenoid for mechanical tripped indicator (F7)
Remote reset solenoid for
mechanical tripped indica-
tor (F7)
- Primary operating range 0.85 ... 1.1 U
s
- Extended operating range
for battery operation
At 24 V DC, 48 V DC
110 V DC
220 V DC
0.7 ... 1.26 U
s
- Power consumption AC/DC VA/W 50/50
- Minimum command duration at U
s
for the remote re-
set solenoid
ms 60
- Short-circuit protection
Smallest permissible DIAZED fuse (gL operational class)/
miniature circuit breaker with C characteristic
2 A TDz (slow)/1 A at 24 V DC
and 48 V DC,
1 A TDz (slow)/1 A at 110 V and
208 ... 250 V
Contact position-driven auxiliary switches (S1, S2, S3, S4, S7, S8)
Rated insulation voltage U
i
V AC/DC 500
Rated operational voltage U
e
V AC/DC 500
Rated impulse withstand voltage U
imp
kV 4
Switching capacity Alternating current
50/60 Hz
- Rated operational voltage U
e
- rated operational current
I
e
/AC-12
I
e
/AC-15
V
A
A
24 ... 230
10
4
380/400
10
3
500
10
2
Direct current - Rated operational voltage U
e
- rated operational current
I
e
/DC-12
I
e
/DC-13
V
A
A
24
10
8
48
8
4
110
3.5
1.2
220
1
0.4
Short-circuit protection Largest permissible DIAZED fuse (gL operational class)
Largest permissible miniature circuit breaker with C characteristic
10 A TDz, 10 A Dz
10 A
Siemens AG 2011
3WL Air Circuit Breakers
31
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
Sizes I to III
Type 3WL1
Ready-to-close signaling switch (S20) (according to DIN VDE 0630)
Switching capacity Alternating current - Rated operational voltage U
e
- Rated operational current I
e
V
A
250
8
Direct current - Rated operational voltage U
e
- Rated operational current I
e
V
A
125
0.4
250
0.2
Short-circuit protection Largest permissible DIAZED fuse (gL operational class) 2 A Dz (quick)
Tripped signaling switch (S24) and signaling switch for auxiliary releases (S22, S23)
(according to DIN VDE 0630)
Switching capacity Alternating current - Rated operational voltage U
e
- Rated operational current I
e
/AC-12
V
A
250
8
Direct current - Rated operational voltage U
e
- Rated operational current I
e
/DC-12
V
A
24
6
125
0.4
250
0.2
Short-circuit protection Largest permissible DIAZED fuse (gL operational class) 6 A Dz (quick)
Tripped signaling switch Signal duration after tripping Until manual or electrical
remote reset (option)
Position signaling switch on guide frame
Type of contact Signal: - "Circuit breaker in connected posi-
tion"
- "Circuit breaker in test position"
- "Circuit breaker in disconnected
position"
3 CO
2 CO
1 CO
or
1 CO
1 CO
1 CO
Rated insulation voltage U
i
50/60 Hz AC
DC
V
V
440
250
Rated operational voltage U
e
V 250
Rated impulse withstand voltage U
imp
kV 4
Switching capacity Rated operational
current I
e
- I
e
/AC-12
- I
e
/AC-15
- I
e
/DC-12
- I
e
/DC-13
- A 300 (AC)
- R 300 (DC)
24 V 10 A, 110/127 V 10 A,
220/240 V 10 A, 320/440 V 10 A
220/240 V 4 A,
320/440 V 3 A,
24 V 10 A, 48 V 2.5 A,
220/240 V 0.2 A,
24 V 3.0 A, 220/240 V 0.1 A
120 V 6 A, 240 V 3 A
125 V 0.22 A, 250 V 0.11 A
Short-circuit protection Largest permissible DIAZED fuse (gL operational class)
Largest permissible miniature circuit breaker with C characteristic
8 A TDz (slow)
8 A TDz (slow)
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
32
Siemens 2012
For the setting range of the operating current Ig, see page 33.
Protection functions ETU15B ETU25B ETU27B
Parameterization by D D D & S
Functional overview of the electronic release system
L
Overload protection
Function can be switched on/off
--
--
--
Setting range I
R
= I
n
... 0.5-0.55-0.6-0.65-0.7-
0.75-0.8-0.85-0.9-1
0.4-0.45-0.5-0.55-0.6-
0.65-0.7-0.8-0.9-1
0.4-0.45-0.5-0.55-0.6-
0.65-0.7-0.8-0.9-1
Switchable overload protection
(I
2
t- or I
4
t-dependent function)
-- -- --
Setting range for time-lag class t
R
at I
2
t 10 s fixed 10 s fixed 10 s fixed
Setting range for time-lag class t
R
at I
4
t -- -- --
Thermal image can be switched on/off -- -- --
Phase failure sensitivity -- At t
sd
= 20 ms (M) At t
sd
= 20 ms (M)
N
Neutral conductor protection -- --
Function can be switched on/off -- --
N conductor setting range I
N
= I
n
... -- -- 1
S
Short-time delayed short-circuit protection --
Function can be switched on/off -- -- --
Setting range I
sd
= I
n
... -- 1.25-1.5-2-2.5-3-4-6-8-10-12 1.25-1.5-2-2.5-3-4-6-8-10-12
Setting range for delay time t
sd
-- 0-M-100-200-300-400 ms 0-M-100-200-300-400 ms
Switchable short-time delayed short-circuit
protection (I
2
t-dependent function)
-- -- --
Setting range for delay time t
sd
at I
2
t -- -- --
Zone Selective Interlocking function -- -- --
I
Instantaneous short-circuit protection
Function can be switched on/off -- -- --
Setting range I
i
= I
n
... 2-3-4-5-6-7-8 Fixed for I
i
20 I
n
, max. 50 kA Fixed for I
i
20 I
n
, max. 50 kA
G
Ground-fault protection -- -- Fixed mounted
Tripping and alarm function -- -- --
Tripping function can be switched on/off -- --
Alarm function can be switched on/off -- -- --
Detection of the ground-fault current through summa-
tion current formation with internal or external N con-
ductor transformer
-- --
Detection of ground-fault current through external
current transformer
-- -- --
Setting range of the operating current I
g
for tripping -- -- A-B-C-D-E
Setting range of the operating current I
g
for alarm -- -- --
Setting range of the delay time t
g
-- -- 100-200-300-400-500 ms
Switchable ground-fault protection characteristic
curve (I
2
t-dependent function)
-- -- --
Setting range for delay time t
g
at
I
2
t -- -- --
Zone Selective Interlocking ground-fault protect.
function
-- -- --
Parameter set switchover
Switchable between parameter set A and B -- -- --
LCD
Alphanumeric LCD (4-line) -- -- --
Graphical LCD (24 V, external power supply required) -- -- --
Communication
CubicleBUS integrated -- -- --
Communication-capable through PROFIBUS DP -- -- --
Measurement function
Measurement-function capable with measurement
function Plus
-- -- --
LED display
Electronic release active
Alarm
ETU fault
L-release --
S-release --
I-release --
N-release -- --
G-release -- --
G-alarm -- -- --
Release through extended protection function -- -- --
Communication -- -- --
Signals from signaling switches with external CubicleBUS modules (relays)
Overload warning -- -- --
Load shedding, load receiving -- -- --
Leading signal overload trip 200 ms -- -- --
Temperature alarm -- -- --
Phase unbalance -- -- --
Instantaneous short-circuit release -- -- --
Short-time delayed short-circuit release -- -- --
Overload trip -- -- --
Neutral conductor release -- -- --
Ground-fault protection release -- -- --
Ground-fault alarm -- -- --
Auxiliary relay -- -- --
ETU fault -- -- --
R
NSE0_00888b
R
sd
sd
i
NSE0_00889a
g
g
NSE00890
NSE00891
Delay time figures given in ms. D & S = Rotary coding and slide switch Available.
M = Motor protection, corresponds to 20 ms. K = communication -- Not available.
D = Rotary coding switch M/K = menu/communication Optional.
Siemens AG 2011
3WL Air Circuit Breakers
33
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
General data
Protection functions ETU45B ETU76B
Parameterization by D & S M/K
Functional overview of the electronic release system
Overload protection
Function can be switched on/off
--
Setting range I
R
= I
n
... 0.4-0.45-0.5-0.55-0.6-
0.65-0.7-0.8-0.9-1
0.4 ... 1
Switchable overload protection (I
2
t- or I
4
t-dependent function)
Setting range for time-lag class t
R
at I
2
t 2-3.5-5.5-8-10-14-17-21-25-30 s 2 ... 30 s
Setting range for time-lag class t
R
at I
4
t 1-2-3-4-5 s 1 ... 5 s
Thermal image can be switched on/off
Phase failure sensitivity At t
sd
= 20 ms (M) (on/off)
Neutral conductor protection
Function can be switched on/off
N conductor setting range I
N
= I
n
... 0.5 ... 1 0.2 ... 2
Short-time delayed short-circuit protection
Function can be switched on/off
Setting range I
sd
= I
n
... 1.25-1.5-2-2.5-3-4-6-8-10-12 1.25 I
n
... 0.8 I
cw
Setting range for delay time t
sd
M-100-200-300-400 ms M-80 ... 4000 ms
Switchable short-time delayed short-circuit protection
(I
2
t-dependent function)
Setting range for delay time t
sd
at I
2
t 100-200-300-400 ms 100 ... 400 ms
Zone Selective Interlocking function By CubicleBUS-Module By CubicleBUS-Module
Instantaneous short-circuit protection
Function can be switched on/off
Setting range I
i
= I
n
... 1.5-2.2-3-4-6-8-10-12-0.8 x I
cs
1.5 I
n
... 0.8 I
cs
Ground-fault protection Module can be retrofitted Module can be retrofitted
Tripping and alarm function
Tripping function can be switched on/off
Alarm function can be switched on/off --
Detection of the ground-fault current through summation cur-
rent formation with internal or external N conductor transformer
Detection of ground-fault current through external
current transformer
Setting range of the operating current I
g
for tripping
A-B-C-D-E A ... E
Setting range of the operating current I
g
for alarm A-B-C-D-E A ... E
Setting range of the delay time t
g
100-200-300-400-500 ms 100 ... 500 ms
Switchable ground-fault protection characteristic curve
(I
2
t-dependent function)
Setting range for delay time t
g
at I
2
t 100-200-300-400-500 ms 100 ... 500 ms
Zone Selective Interlocking ground-fault protect. function By CubicleBUS-Module By CubicleBUS-Module
Parameter set switchover
Switchable between parameter set A and B --
LCD
Alphanumeric LCD (4-line) --
Graphical LCD (24 V, external power supply required) --
Communication
CubicleBUS integrated
Communication-capable through PROFIBUS DP
Measurement function
Measurement-function capable with measurement function
Plus
LED display
Electronic release active
Alarm
ETU fault
L-release
S-release
I-release
N-release
G-release (only with ground-fault protection module) (only with ground-fault protection module)
G-alarm (only with ground-fault protection module) (only with ground-fault protection module)
Release through extended protection functions
Communication
Signals from signaling switches with external CubicleBUS modules (relays)
Overload warning
Load shedding, load receiving
Leading signal overload trip 200 ms
Temperature alarm
Phase unbalance
Instantaneous short-circuit release
Short-time delayed short-circuit release
Overload trip
Neutral conductor release
Ground-fault protection release (only with ground-fault protection module) (only with ground-fault protection module)
Ground-fault alarm (only with ground-fault protection module) (only with ground-fault protection module)
Auxiliary relay
ETU fault
Setting range of the operating current Ig Increment size for settings for ETU76B via menu For legend see page 32.
Size I and size II Size III From ... to Increment
size
From ... to Increment
size
A 100 A 400 A 0 ... 1 0.1 1000 ... 1600 50
B 300 A 600 A 1 ... 100 1 1600 ... 10000 100
C 600 A 800 A 100 ... 500 5 10000 ... max 1000
D 900 A 1000 A 500 ... 1000 10
E 1200 A 1200 A
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
34
Siemens 2012
Characteristic curves
2)
Every release type and every setting has its own characteristic
curve. Only a selection is shown in the following. The character-
istic curves each show the largest and smallest setting range of
3WL circuit breakers with 1000 A rated current at 500 V rated
voltage with various releases. In order to obtain a complete trip-
ping characteristic, the relevant parts of the characteristics have
to be combined. The characteristic curves show the behavior of
the release when it is activated by a current that is already flow-
ing before the tripping operation. If the overcurrent tripping oc-
curs immediately after switch on and the release is therefore not
yet enabled, the opening time is extended, depending on the
level of the overcurrent by up to 15 ms. In order to determine the
break-times of the circuit breakers, approximately 15 ms must
be added to the opening times shown for the arcing time.
Refer to the following legend for tolerances.
The characteristic curves shown apply to ambient temperatures
at the circuit breaker between -5 and +55 C. The release can
be operated at ambient temperatures of -20 to +70C.
An extended tolerance band can apply at these temperatures.
3WL circuit breaker with ETU25B release,
LSI characteristic curve
3WL circuit breaker with ETU27B release,
G characteristic curve
Tolerances for the set currents
L: Tripping operations between 1.05 and 1.2 x I
R
S: 0 %, +20 %
I: 0 %, +20 %
G: 0 %, +20 %
Tolerances for the tripping times
L: 20 %, +0 % for I
2
t characteristic curve
S: 0 %, +60 ms or -0 %, 10 % for tripping times greater than 600 ms
I: <50 ms
G: 0 %, +60 ms or -0 %, 10 % for tripping times greater than 600 ms
3WL circuit breaker with ETU15B release
3WL circuit breaker with ETU27B release,
LSIN characteristic curve
3WL circuit breaker with ETU45B release,
S characteristic curve
1)
Sizes I and II: 100 ... 1200 A
Size III: 400 ... 1200 A.
2)
With single-pole loading in the lowest rated current range, the response
times of the short-circuit release can be extended by approx. 10 % and
the tripping times by approx. 15% compared to the characteristic curve.
0,01
0,1
1
10
100
1000
10000
0,1 1 10 100
N
S
E
0
_
0
1
5
2
0
[
s
]
/
n
R
min
R
max
0,4 ... 1,0 x
n
sd
min
1,25 ... 12 x
n
0 ... 0,4 s
sd
max
sd
max
sd
min
i
> 20 x
n
max. 50 kA
i
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
100 1000 10000 100000
N
S
E
0
_
0
1
5
2
1
[
s
]
g
min g
max
100 ... 1200 A
1)
0,1 ... 0,5 s
g
max
g
min
A
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
0,1 1 10 100
N
S
E
0
_
0
1
5
2
7
[
s
]
/
n
i
min
i
max
R
min
R
max
0,5 ... 1,0 x
n
2 ... 8 x
n
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
0,1 1 10 100
N
S
E
0
_
0
1
5
1
9
[
s
]
/
n
R
min
R
max
0,4 ... 1,0 x
n
N
sd
min
1,25 ... 12 x
n
0 ... 0,4 s
sd
max
sd
max
sd
min
i
> 20 x
n
max. 50 kA
i
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
0,1 1 10 100
N
S
E
0
_
0
1
5
2
3
a
[
s
]
sd
0,1 ... 0,4 s
/
n
2
sd
1,25 ... 12 x
n
2
sd
sd
0,02 ... 0,4 s
O
p
e
n
i
n
g
T
i
m
e
= const
= const
= const
Siemens AG 2011
3WL Air Circuit Breakers
35
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Every release type and every setting has its own characteristic
curve. Only a selection is shown in the following. The character-
istic curves each show the largest and smallest setting range of
3WL circuit breakers with 1000 A rated current at 500 V rated
voltage with various releases.
In order to obtain a complete tripping characteristic, the relevant
parts of the characteristics have to be combined.
The characteristic curves show the behavior of the release when
it is activated by a current that is already flowing before the trip-
ping operation. If the overcurrent tripping occurs immediately af-
ter switch on and the release is therefore not yet enabled, the
opening time is extended, depending on the level of the overcur-
rent by up to 15 ms. In order to determine the total break-times
of the circuit breakers, approximately 15 ms must be added to
the opening times shown for the arcing time.
Refer to the following table for tolerances.
The characteristic curves shown apply to ambient temperatures
at the circuit breaker between -5 and +55 C. The release can
be operated at ambient temperatures of -20 to +70C (ETU76B
with graphics display up to +55 C). An extended
tolerance band can apply at these temperatures.
3WL circuit breaker with ETU45B and ETU76B release, L characteristic
curve
3WL circuit breaker with ETU45B and ETU76B release, I characteristic
curve
1)
Sizes I and II: 100 ... 1200 A
Size III: 400 ... 1200 A.
3WL circuit breaker with ETU45B and ETU76B release, G characteristic
curve
3WL circuit breaker with ETU76B release, S characteristic curve
Further characteristic curves are shown in the manual and the
planning and configuring tool SIMARIS deSign, or ask your
Siemens contact person.
Tolerances for the set currents
L: Tripping operations between 1.05 and 1.2 I
R
S: 0 %, +20 %
I: 0 %, +20 %
G: 0 %, +20 %
Tolerances for the tripping times
L: 20 %, +0 % for I
2
t characteristic curve
S: 0 %, +60 ms or -0 %, 10 % for tripping times greater than 600 ms
I: <50 ms
G: 0 %, +60 ms or -0 %, 10 % for tripping times greater than 600 ms
0,01
0,1
1
10
100
1000
10000
0,1 1 10 100
N
S
E
0
_
0
1
5
2
2
a
[
s
]
R
/
n
0,4 ... 1,0 x
n
R
2
4
2 ... 30s for
4
= const
2
= const
1 ... 5s for
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
0,1 1 10 1
N
S
E
0
_
0
1
5
2
4
a
[
s
]
/
n
i
1,5 x
n
... 0,8 x
cs
/
cs
O
p
e
n
i
n
g
t
i
m
e
0,01
0,1
1
10
100
1000
10000
100 1000 10000 100000
N
S
E
0
_
0
1
5
2
5
a
g
0,1 ... 0,5 s
g
[
s
]
100 ... 1200 A
1)
A
O
p
e
n
i
n
g
t
i
m
e
2
= const
0,01
0,1
1
10
100
1000
10000
0,1 1 10 1
N
S
E
0
_
0
1
5
2
6
a
[
s
]
/
n /
cw
sd
0,02 ... 4 s
2
sd
0,1 ... 0,4 s
1,25 x
n
... 0,8 x
cw
sd
O
p
e
n
i
n
g
t
i
m
e
= const
= const
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
36
Siemens 2012
Dimensional drawings
Voltage transformer for 3WL air circuit breakers
Current transformers for overload protection in the N con-
ductor
External current transformers for N conductor with copper con-
nection pieces
Dimensions for option with door interlocking
1)
Mounting surface
2)
Center 3WL circuit breaker operator panel
3)
8 mounting holes for door sealing frame
4)
3 mounting holes for door interlocking
External current transformers for N conductor without copper
connection pieces
Door cutout for operator panel
Door cutout for operator panel
using the door sealing frame
Size I, 3WL9 111-0AA31-0AA0
Size II, 3WL9 111-0AA32-0AA0
Size III, 3WL9 111-0AA33-0AA0
NSE0_01103b
260
1
2
5
87
For mounting on
35 mm standard
mounting rail
83
55
5
1
4
4
6
8
1
3
0
N
S
E
0
_
0
0
6
0
6
b
1 5
97
41
1
7
0
1 3, 5
9
1
2
4
30 30
90
50, 5
31 0
1 31
5
1
4
4
6
8
1
3
0
N
S
E
0
_
0
0
6
0
7
b
1 3, 5
1
7
0
1 1 3
9
1
2
4
30
1 23
52
1 60
31 0
1
7
0
30 30
5
1
4
4
6
8
1
3
0
N
S
E
0
_
0
0
6
0
8
b
1 3, 5
1 84
2
4
9
1
Size I, 3WL9 111-0AA21-0AA0
Size II, 3WL9 111-0AA22-0AA0
Size III, 3WL9 111-0AA23-0AA0
Door cutout with edge protector
Inner dimensions with mounted
edge protector
Option with/without door interlocking
N
S
E
0
_
0
1
3
7
5
60
8
1
2
2
9
6
,
8
8
R 1 3, 1
R 22
1 8
36
1 6
70
83
8
,
9
4
0
51
N
S
E
0
_
0
1
3
7
6 5
4
88
1
1
5
1
3
1
R 27
95
1 1 3 3
6
5
,
5
51
51
N
S
E
0
_
0
1
3
7
7
1 60
4
5
1 61
1 84
3
3
1
R 1 5
1
0
7
1
2
3
3
4
0
2
4
0
295
NSE0_001 64c
40 1 20
300
31 4
40 1 20
R5 R5
2)
3)
6
5
5, 5
1
4
0
1
7
5
3
5
0
5, 5
1
4
0
1
8
5
1
8
0
5, 5
NSE0_0061 0c
1 ) 4)
21
1 2
40
1
1
,
5
Siemens AG 2011
3WL Air Circuit Breakers
37
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
CubicleBUS modules
3WL9 111-0AT2.-0AA0
Breaker Data Adapter (BDA)
3WL9 111-0AT28-0AA0
3WL9 111-0AT33-0AA0
4
7
,
5
70
9
4
86
6
N
S
E
0
_
0
2
0
8
5
81,9
45,5
38
19
1
5
3
30
N
S
E
0
_
0
2
0
8
6
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
38
Siemens 2012
Door cutout for operator panel using protective cover IP55
Safety clearance from grounded parts
All safety clearances above the circuit breaker refer to the upper
edge of the auxiliary connector - not to the upper edge of the arc
chute! See dimensional drawings on pages 39 to 47, Parts 4)
and 5).
Protective cover, IP55
Safety clearances from live parts
1)
Value for plate; 0 mm for struts and grids
2)
40 mm (size II: 70 mm) for plates, which cover the lateral openings in the
guide frame
3)
Not for switching capacity S.
4)
For switching capacity S: 100 mm.
Rated operational voltage
V/AC
Above
auxiliary connector
mm
Lateral
(each side)
mm
Rear
mm
Size I, fixed-mounted version
500 75
1)
0 0
690 75
1)
0 0
Size I, withdrawable version,
without arc chute cover
500 50
1)
0 0
690 50
1)
0 0
Size I, withdrawable version,
with arc chute cover
500 0 0
2)
0
690 0 0
2)
0
Size II, fixed-mounted version
500 75
1)
0 0
690 75
1)
0 0
1000 180 0 0
Size II, withdrawable version,
without arc chute cover
500 50
1)
0 0
690 50
1)
0 0
1000 100 0 0
Size II, withdrawable version,
with arc chute cover
500 0 0
2)
0
690 0 0
2)
0
Size III, fixed-mounted version
500 75
1)
0 0
690 75
1)
0 0
1000 180 0 0
Size III, withdrawable version,
without arc chute cover
500 50
1)
0 0
690 50
1)
0 0
1000 100 0 0
Size III, withdrawable version,
with arc chute cover
500 0 0
2)
0
690 0 0
2)
0
DC non-automatic air circuit breakers
300 45 0 0
600 200 0 0
1000 150 0 0
6
8
3
4
0
-
3
5
0
N
S
E
0
_
0
1
0
2
9
c
295-300
341
4 x R5
4 x 5,5
7
2
7
2
7
0
Circuit breaker mounting level
Mounting surface for circuit breaker
or guide frame
Rated operational voltage
V/AC
Above
auxiliary connector
mm
Lateral
(each side)
mm
Rear
mm
Size I, fixed-mounted version
500 150 20 20
690 300 50 125
1000 500
3)
100
3)
140
3)
Size I, fixed-mounted version,
with arc chute cover
500 14 50
4)
14
690 14 225
4)
14
Size I, withdrawable version,
without arc chute cover
500 150 20 14
690 300 50 14
1000 500
3)
100
3)
140
3)
Size I, withdrawable version,
with arc chute cover
500 14 100 14
690 14 100 14
Size II, fixed-mounted version
500 250 50 20
690 600 100 140
1000 430 100 125
Size II, withdrawable version,
without arc chute cover
500 250 50 14
690 600 100 30
1000 350 100 14
Size II, withdrawable version,
with arc chute cover
500 14 50 14
690 14 225 14
Size III, fixed-mounted version
500 75 20 20
690 500 100 125
1000 430 100 125
Size III, withdrawable version,
without arc chute cover
500 50 20 14
690 500 100 14
1000 350 100 14
Size III, withdrawable version,
with arc chute cover
500 14 50 14
690 14 200 14
8
5
148 313
4
3
5
1
7
N
S
E
0
_
0
1
0
3
0
b
395
400
Circuit breaker
mounting level
Siemens AG 2011
3WL Air Circuit Breakers
39
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Size I, up to 2000 A, fixed-mounted version, 3 and 4-pole
4-pole version
1)
Mounting space for removal of the arc chutes.
2)
Arc quenching space 690 V circuit breaker facing grounded or non-
conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the
system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with screwless connection method.
6)
Dimension to inside surface of the closed cabinet door.
7)
Fixing points for mounting the circuit breaker in the system;
4 setting nut M8.
8)
"Secure OFF" locking device (optional accessory).
9)
Key operation (optional accessory).
11)
Terminal face.
14)
Space for electrical auxiliary circuit connections.
18)
Circuit breaker upper edge, only 690 V (+20 %) and 1000 V circuit
breakers.
19)
Arc quenching space, circuit breaker facing grounded or non-conduc-
tive surfaces, only 690 V (+20 %) and 1000 V circuit breakers.
For safety clearances to grounded parts and to live parts see
page 38.
Standard version
Horizontal connection
Optional connection variants Front connection (single),
not suitable for circuit breakers with rated current 2000 A
Front connection (double hole)
according to DIN 43673
Vertical connection
15 270
300 10
390
4
3
7
,
5
1
2
3
,
5
4
4
0
,
5
2
7
5
4) 5)
NSE0_00611h
82 c
47
d
e
N
S
E
0
_
0
0
6
1
2
c
6
60 90 90 90
55 55 55 55
3)
2
6
4
2
1
N
S
E
0
0
6
1
3
b
13,5
3
5
3
5
11)
NSE0_00614h
a
a
1
5
0
2
7
5
5
1
6
4
5
1
,
5
5
4
1
,
5
6
2
1
1) 2)
14)
9)
150
210
106
230 127
6) 45
8)
33,5
60,5
3
2
7
,
5
4
6
1
,
5
7
6
3)
5,5
18)
19)
7)
g
f
6
c 82
47
N
S
E
0
_
0
0
6
1
5
h
90 90 90 60
55 55 55 55
3)
1
4
4
0
4
2
1
4
0
13,5
N
S
E
0
0
6
1
6
b
8
0
8
0
11)
410
320
58 139
60
55
90 90 90
3)
7)
7)
13,5
N
S
E
0
_
0
0
6
1
7
j
3
5
11)
(150) 110
4x 9
4x M8
20
N
S
E
0
_
0
0
6
1
8
h
7)
11)
6
0
3
0
2
6
7
,
5
1
2
7
,
5
13,5
113,5
128,5
35
60 90 90 90
b
3)
NSE00619
3)
90 90 90 60
NSE00620
Rated
circuit breaker
current
A
a b c d e f g
Up to 1000 10 10 10 11 451 34 541
1250 ... 2000 15 20 15 6 461 39 551
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
40
Siemens 2012
Size I, up to 2000 A, withdrawable version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
Flange connections (see following page)
Standard version
Horizontal connection
Optional connection variants Front connection (single),
not suitable for circuit breakers with rated current 2000 A
Front connection (double hole)
according to DIN 43673
Vertical connection
4-pole version
2)
For guide frame without arc chute cover, arc quenching space 690 V circuit
breaker facing grounded or non-conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with screwless connection method.
6)
Dimension to inside surface of the closed cabinet door.
7)
Circuit breaker in connected position.
8)
Circuit breaker in test position.
9)
Circuit breaker in disconnected position.
10)
Fixing holes 10 mm.
11)
Terminal face.
18)
Circuit breaker upper edge, only 690 V (+20 %)and 1000 V circuit breakers.
19)
Arc quenching space, circuit breaker facing grounded or non-conductive surfaces,
only 690 V (+20 %) and 1000 V circuit breakers.
55
270
30 13
210
300
320
5) 4)
10)
1
2
3
,
5
2
7
5
4
6
8
,
5
4
6
5
,
5
NSE0_00621j
169,5 c
62,5
1
1
4
0
3
N
S
E
0
0
6
2
2
a
6
90 90 90
55 55 55 55
1 5
3)
N
S
E
0
_
0
0
6
2
3
b
2
6
3
7
3
3
5
3
5
1 1 )
1 3, 5
260
350
6
9
2
8
7
45
88,5
121,5
140,5
220
3)
7) 8)
9)
10)
58
6)
7
6
327
NSE0_00624g
12)
367,5
382,5
1
5
0
a
a
2
7
5
4
6
0
5
1
9
6
2
0
3
2
7
,
5
4
0
3
1
27
42
14
19)
18)
2)
5
1
8
,
5
10)
62,5
6
c
4
9
3
3
4
169,5
N
S
E
0
_
0
0
6
2
5
h
350
260
55
13,5
4
0
8
0
3
7
3
N
S
E
0
_
0
0
6
2
6
h
4
0
1
4
8
0
6
9
2
8
7
55 55 55
11)
15 90 90 90
55 55 55 55
68 139
25 270
320
410
13,5
N
S
E
0
0
6
2
7
a
3
8
11)
NSE0_00628h
10)
11)
13,5
150
165
6
0
3
0
2
6
7
,
5
1
2
7
,
5
38
350
260
15
3)
90 90 90
b
2
8
7
6
9
N
S
E
0
_
0
0
6
2
9
h
260
350
2
8
7
6
9
55
15
90
3)
10) 10)
90 90
N
S
E
0
_
0
0
6
3
0
h
Rated circuit breaker current
A
a b c
Up to 1000 10 10 10
1250 ... 2000 15 15 15
Siemens AG 2011
3WL Air Circuit Breakers
41
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Size I, up to 2000 A, withdrawable version, 3 and 4-pole
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the
system.
10)
Fixing holes 10 mm.
For safety clearances to grounded parts and to live parts see
page 38.
For more connection options see previous page.
Flange connection
121
N
S
E
0
_
0
0
6
3
1
h
10)
14
350
260
55
M 12
3)
3
3
2
8
2
,
5
1
4
2
,
5
2
6
N
S
E
0
_
0
0
6
3
2
h
6
9
2
8
7
5
9
5
9
55 55 55
15 90 90 90
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
42
Siemens 2012
Size II, up to 4000 A, fixed-mounted version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
Flange connections (see following page)
Standard version
Horizontal connection
Optional connection variants
Front connection (single)
Front connection (double hole)
according to DIN 43673
Vertical connection up to 3200 A
4-pole version
1)
Mounting space for removal of the arc chutes.
2)
Arc quenching space " 690 V" circuit breaker facing grounded or non-conductive
surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
Fixing points for mounting the circuit breaker in the system.
11)
Terminal face.
12)
Circuit breaker upper edge, only 1000 V and 1150 V circuit breaker.
13)
Arc quenching space, 1000 V and 1150 V circuit breaker facing grounded or non-
conductive surfaces.
14)
Space for electrical auxiliary circuit connections.
10
270
85
440
570
5) 4)
1
2
3
,
5
2
7
5
4
4
0
,
5
4
3
7
,
5
NSE0_00633a
82 c
47
d
e
N
S
E
0
_
0
0
6
3
4
d
6
90 130 130 130
40
90 90 90 90
3)
40
2
6
4
2
1
N
S
E
0
0
6
3
5
c
3
5
3
5
11)
13,5
NSE0_00636e
150
210
230
45
5,5
127
1
5
0
2
7
5
3
2
7
,
5
4
6
1
,
5
7
6
5
4
1
,
5
a
a
1)
6)
3)
106
4
5
1
,
5
5
1
6
6
2
1
13)
14)
2)
12)
82 c
47
g
f
N
S
E
0
_
0
0
6
3
7
d
6
90 130 130 130
40
90 90 90 90
3)
40 4
0
4
0
1
4
4
2
1
N
S
E
0
0
6
3
8
c
11)
8
0
8
0
13,5
130 90
30 30
130 130
90
3
5
11)
7)
9
7)
460
128 139
590
3) 13,5
N
S
E
0
_
0
0
6
3
9
f
113,5
128,5
1
3
4
,
5
9
8 2
9
0
3
0
3
0
NSE00640b
1
3
,
5
35
11)
90 130 130 130
b
3)
NSE00641
3)
130 130 90 130
NSE00642
Rated
circuit breaker
current
A
a b c d e f g
Up to 2000 10 15 10 11 451 34 541
2500 15 15 20 6 461 39 551
3200 30 30 20 6 461 39 551
Siemens AG 2011
3WL Air Circuit Breakers
43
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Size II, up to 4000 A, fixed-mounted version, 3 and 4-pole
1)
Mounting space for removal of the arc chutes.
2)
Arc quenching space " 690 V" circuit breaker facing grounded or non-
conductive surfaces.
11)
Terminal face.
For safety clearances to grounded parts and to live parts see
page 38.
For more connection options see previous page.
Vertical connection 4000 A
200 130 200
10
20
N
S
E
0
_
0
1
8
6
8
a
142
162
3
0
3
0
85 Nm
11)
40
1
0
0
1)
2)
3
4
5
,
5
7
9
,
5
13,5 5
1
6
5
4
1
,
5
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
44
Siemens 2012
Size II, up to 3200 A, withdrawable version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
For vertical connection and flange connection see following
page.
Standard version
Horizontal connection
Optional connection variants
Front connection (single)
Front connection (double hole)
according to DIN 43673
4-pole version
2)
For guide frame 690 V, without arc chute cover, arc quenching space facing
grounded or non-conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
3WL circuit breaker in connected position.
8)
3WL circuit breaker in test position.
9)
3WL circuit breaker in disconnected position.
10)
Fixing holes, 10 mm in diameter.
11)
Terminal face.
12)
Guide frame upper edge only 1000 V and 1150 V AC version.
13)
Arc quenching space, 1000 V and 1150 V circuit breaker facing grounded or
non-conductive surfaces.
55 350
270
40
480
10) 10)
4
6
5
,
5
1
2
3
,
5
2
7
5
4
6
8
,
5
NSE0_00643b
4) 5)
c
62,5
169,5
1
1
4
0
3
N
S
E
0
0
6
4
4
b
6
55 1 30 1 30 1 30
40
90 90 90 90
3)
45, 1
2
6
3
7
3
40
N
S
E
0
_
0
0
6
4
5
c
3
5
3
5
1 1 )
1 3, 5
400
530
2
8
7
6
9
220 27
42
4
0
3
1
45
6)
88,5
121,5
140,5
58
8)
9)
7
6
3
2
7
,
5
5
1
8
,
5
1
5
0
a
a
2
7
5
4
6
0
5
2
0 6
2
0
327
367,5
382,5
13)
12)
2)
7)
10)
14
9
3)
NSE0_00646f
c
62,5
169,5
3
4
4
9
3
N
S
E
0
0
6
4
7
b
6
55 1 30 1 30 1 30 45
40
90 90 90 90
3)
1
4
4
0
4
0
3
7
3
40
N
S
E
0
_
0
0
6
4
8
c
8
0
1 1 )
8
0
1
3
,
5
400
530
2
8
7
6
9
30
138 139
95 270
460
590
30
N
S
E
0
0
6
4
9
a
13,5
3
8
11)
90
400
530
90 90 90
55 45 130 130 130
10)
10)
6
9
2
8
7
N
S
E
0
_
0
0
6
5
2
b
3)
Rated circuit breaker current
A
a b c
Up to 2000 10 15 10
2500 15 15 20
3200/4000 30 30 20
Siemens AG 2011
3WL Air Circuit Breakers
45
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Size II, up to 4000 A, withdrawable version, 3 and 4-pole
4-pole version
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the
system.
11)
Terminal face.
For safety clearances to grounded parts and to live parts see
page 38.
For more connection options see previous page.
Vertical connection up to 3200 A
Vertical connection 4000 A
Flange connection
157
172
1
3
5
1
0
0
2
9
0
3
0
3
0 N
S
E
0
0
6
5
0
a
38
11)
55 45 1 30 1 30 1 30
b
3)
NSE0_00651 a
400
530
2
8
7
6
9
11)
200
1
0
0
N
S
E
0
_
0
1
8
6
9
40
3
0
3
0
177
197
130
55
200
10
20
45
3
1
5
,
5
1
0
9
,
5
4,6
121
N
S
E
0
0
6
5
3
45 1 30 1 30 1 30
90 40
3)
5
9
5
9
2
6
3
3
2
8
2
,
5
1
4
2
,
5
N
S
E
0
_
0
0
6
5
4
a
M 1 2
400
530
2
8
7
6
9
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
46
Siemens 2012
Size III, up to 6300 A, fixed-mounted version, 3 and 4-pole
4-pole version
1)
Mounting space for removal of the arc chutes.
2)
Arc quenching space " 690 V" circuit breaker facing grounded or
non-conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the
system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
Fixing points for mounting the circuit breaker in the system.
11)
Terminal face.
12)
Circuit breaker upper edge, only 1000 V circuit breaker and circuit
breaker with switching capacity C.
13)
Arc quenching space, 1000 V circuit breaker and circuit breaker with
switching capacity C, facing grounded or non-conductive surfaces.
14)
Space for electrical auxiliary circuit connections.
For safety clearances to grounded parts and to live parts see
page 38.
Standard version
Horizontal connection
Optional connection variants
Front connection (single)
Front connection (double hole)
according to DIN 43673
Vertical connection
12 205 270
680
890
4) 5)
4
3
7
,
5
1
2
3
,
5
2
7
5
4
4
0
,
5
NSE0_00655a
N
S
E
0
0
6
5
6
c
1
1
4
5
1
82
20
47
6
130 210 210 210
50
160 160 160
3)
2
6
4
2
1
160
N
S
E
0
0
6
5
7
c
3
5
3
5
11)
50
13,5
NSE0_00658e
150
210
230
45
35
5,5
127
1
5
0
2
7
5
3
2
7
,
5
4
6
1
,
5
7
6
5
4
1
,
5
3
0
3
0
6)
3)
106
4
5
1
,
5
5
1
6
6
2
1
13) 1)
14)
2)
12)
82
20
47
3
4
5
4
1
N
S
E
0
_
0
0
6
5
9
d
6
1 30 21 0 21 0 21 0
50
1 60 1 60 1 60 1 60
3)
4
0
4
2
1
4
0
1
4
N
S
E
0
_
0
0
6
6
0
c
8
0
1 1 )
8
0
1 3, 5
50 50 50
160
210
704
914
130
210
15
210
248 139
7) 7)
30
N
S
E
0
_
0
0
6
6
1
e
13,5
3
5
11)
M10
3)
142
162
40
107
N
S
E
0
0
6
6
2
a
9
4
,
5 1
2
0
3
3
0
,
5
3
0
1
5
13,5
40
11)
85 210 210 210
10
3)
20
NSE00663
3)
130 210 210 210 130
NSE00664a
Siemens AG 2011
3WL Air Circuit Breakers
47
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Size III, up to 6300 A, withdrawable version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
Flange connections (see following page)
Standard version
Horizontal connection up to 5000 A
Optional connection variants
Front connection (single hole),
up to 4000 A
Front connection (double hole)
according to DIN 43673,
up to 4000 A
Vertical connection, up to 6300 A
4-pole version
2)
For guide frame 690 V, without arc chute cover, arc quenching space facing
grounded or non-conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
3WL circuit breaker in connected position.
8)
3WL circuit breaker in test position.
9)
3WL circuit breaker in disconnected position.
10)
Fixing holes, 10 mm in diameter.
11)
Terminal face.
12)
Guide frame upper edge only 1000 V and 150/130 kA guide frame.
13)
Arc quenching space, 1000 V circuit breaker and circuit breaker with switching
capacity C, facing grounded or non-conductive surfaces.
5) 4)
57
590
800
160 270
10)
10) 10)
1
2
3
,
5
2
7
5
4
6
8
,
5
4
6
5
,
5
NSE0_00665b
20
62,5
169,5
1
1
4
0
3
N
S
E
0
0
6
6
6
b
6
57
85 21 0 21 0
50
1 60 1 60 1 60 1 60
590
800
21 0
2
6
3
7
3
N
S
E
0
_
0
0
6
6
7
c
3
5
3
5
1 1 )
50 1
3
,
5
630
840
2
8
7
6
9
220 27
42
4
0
3
1
45
6)
88,5
121,5
140,5
58
8)
9)
7
6
3
2
7
,
5
5
1
8
,
5
1
5
0
3
0
3
0
2
7
5
4
6
0
5
2
0 6
2
0
327
367,5
382,5
13)
7)
12)
2)
10)
14
3)
9
NSE0_00668d
20
62,5
169,5 3
4
4
9
3
N
S
E
0
0
6
6
9
b
6
57
1 60 1 60 1 60 1 60
85 21 0 21 0 21 0
800
590
50
1
4
4
0
3
7
3
4
0
N
S
E
0
_
0
0
6
7
0
c
8
0
8
0
1 1 )
50
1
3
,
5 630
840
2
8
7
6
9
704
30
30
914
217 270
260 139
30 13,5
N
S
E
0
0
6
7
1
a
3
8
11)
177
197
24
9
4
,
5
1
2
4
,
5
3
0
3
3
0
,
5
N
S
E
0
0
6
7
2
a
13,5
38
11)
57
a
590
91 4
800
b 21 0
1 0
20
704
NSE0_00673b
b
630
840
2
8
7
6
9
160
210 85 57 210 210
630
840
160 160 160
6
9
2
8
7
N
S
E
0
_
0
0
6
7
4
a
Rated circuit breaker current
A
a b
4000 40 210
5000 40 210
6300 5 245
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
48
Siemens 2012
Size III, up to 6300 A, withdrawable version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
For more connection options see previous page.
Flange connection, up to 4000 A
121
N
S
E
0
0
6
7
5
85 21 0 21 0 21 0
30
57
590
800
91 4
1 60 1 60 1 60 1 60
704
5 1
4
2
,
5
2
8
2
,
5
5
9
5
9
2
6
3
3
N
S
E
0
_
0
0
6
7
6
a
630
840
M
1
2
2
8
7
6
9
Siemens AG 2011
3WL Air Circuit Breakers
49
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Circuit diagrams
Terminal assignment diagram
Internal wiring
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
5
4
3
2
1
24 V DC input
Remote reset bell alarm & tripped indicator F7
G transformer S2
N sensor S2
N sensor S1
ext. voltage transformer Com
ext. voltage transformer L3
ext. voltage transformer L2
ext. voltage transformer L1
0 V DC
24 V DC
G transformer S1
"Spring charged" signal S21
1st auxiliary release F1 "ST"
S1 "NO"
S1 "NC"
Closing solenoid
"Ready to close" signal S20
S2 "NO"
S2 "NC"
F4 only "quick OFF"
F4 only "quick OFF"
2nd auxiliary release: F2 "ST", F3 "UVR", F4 "UVR td"
S3 "NO" or S7 "NO"
S3 "NC" or S7 "NO"
S4 "NO" or S8 "NO"
S4 "NC" or S8 "NO"
EMERGENCY STOP
or short terminals
Terminals External wiring
L
L+
14
13
12
11
10
9
8
7
6
5
4
3
2
1
N
S
E
0
_
0
0
6
0
5
p
+ BUS
BUS
Short terminals if no N-sensor
M
Local electric close S10
opt. motor main switch S12
Charging motor
(Option F02/F12)
/COM16
1
2
3
4
5
6
7
8
9
D
P
W
r
it
e
E
n
a
b
le F
r
e
e
F
r
e
e
C
lo
s
e
O
p
e
n
+
I
N
O
U
T
E
x
t
e
r
n
a
l
I
n
t
e
r
n
a
l
Y
1
F
1
,
2
e.g. current transformer in the
star point of power transformer
or a summation current
transformer 1200 A /1A
Trip signalling switch S24
(position after tripping)
Signaling contact at the 1 st auxiliary release
S23
Signaling contact at the 2nd auxiliary release
Termination resistor,
if not external CB-module!
N
o
t
a
v
a
i
l
a
b
l
e
w
i
t
h
c
o
m
m
u
n
i
c
a
t
i
o
n
c
o
n
n
e
c
t
i
o
n
"
F
0
2
"
o
r
F
1
2
.
C
O
M
1
5
/
C
O
M
1
6
m
o
d
u
l
e
i
s
a
t
p
o
s
i
t
i
o
n
"
-
X
7
"
.
optional
Accessories
(Auxiliary switch S1, S2 = Standard)
(sw) (br)
L+
L
c
L+
c
L+
L
c
c
L+
L
c
L+
L
c
N
L3
L2
L1
Siemens AG 2011
3WL Air Circuit Breakers
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
50
Siemens 2012
Example of an overall circuit diagram for 3WL circuit breaker
(3WL1. .......4GN4Z C11+C22 +K07)
Manual/motorized operating mechanism with stored-energy fea-
ture with electrical ON button (option C11), with ready-to-close
signaling switch (optionC22), with LSING release, with "UVR" un-
dervoltage release (F3), with "ST" shunt release (F1), with tripped
signaling switch (option K07), with auxiliary switch 4 NO + 4 NC.
Function diagram of
3WL circuit breaker
-A1 ETU release
-S1/-S2 1st auxiliary switch block (2 NO + 2 NC)
-S3/-S4 2nd auxiliary switch block (2 NO + 2 NC)
-S7 (optional) 2nd auxiliary switch block, S7 (2 NO) can be used
if there is no S3 - S3 and S7 have
the same terminal assignment/mounting space
-S8 (optional) 2nd auxiliary switch block, S8 (2 NO) can be used
if there is no S4 - S4 and S8 have
the same terminal assignment/mounting space
3WL1. ..-.....-...2 (2 NO + 2 NC) S1+S2
3WL1. ..-.....-...4 (4 NO + 4 NC) S1+S2+S3+S4
3WL1. ..-.....-...7 (6 NO+ 2 NC) S1+S2+S7+S8
3WL1. ..-.....-...8 (5 NO + 3 NC) S1+S2+S3+S8
-S10 Electrical ON button
-S11 Internal motor shutdown switch (if spring is tensioned)
-S12 Motor shutdown switch
(no automatic tensioning of spring)
-S20 Ready-to-close signaling switch
-S24 Tripped signaling switch
-F1 1st auxiliary release shunt release
-F3 2nd auxiliary release undervoltage release
-F5 Tripping solenoid
-M Motor for "charging store"
-P Stored-energy mechanism
-QS Actuator lever for "stored-energy feature"
-Q1 Main contacts
-T1/-T2/-T3 Current transformers
-X5/-X6/-X7/-X8 Terminals
-Y1 Closing solenoid
-R Indicator and reset button for release
-X8.9/-X8.10 Connection option: external neutral conductor trans-
former
M
R
-S4 -S3 -S2 -S1 -Q1
L1
(L+)
-
X
7
.
9
-
X
6
.
7
-
X
6
.
1
4
-
X
5
.
1
2
-
X
5
.
2
-
X
6
.
6
-
X
7
.
1
2
-
X
7
.
1
4
QS P
N
(L-)
-S11
-Y1
-F1
-F3
-T3
-T1
-T2
1 3 5 -
X
6
.
1
2
-
X
6
.
1
0
-
X
6
.
4
-
X
6
.
2
-
X
5
.
1
0
-
X
5
.
8
-
X
5
.
6
-
X
5
.
4
2 4 6
-
X
6
.
1
1
-
X
6
.
9
-
X
6
.
3
-
X
6
.
1
-
X
5
.
9
-
X
5
.
7
-
X
5
.
5
-
X
5
.
3
-
X
8
.
9
-
X
8
.
1
0
*
N
(L-)
ETU
L
S
I
G
N N
-A1
-F5
-
S
2
4
-
S
2
0
-
X
6
.
5
-
X
7
.
1
3
-
X
5
.
1
1
-
X
6
.
1
3
-
X
6
.
8
-
X
5
.
1
N
S
E
0
_
0
1
5
5
8
b
L1
(L+)
mech.
mech.
-
S
1
0
U<
-S12
version
OFF
ON
ON
* Short terminals, if no N sensor
ON
OFF
electr.
release
contact
NSE0_01559c
M1
P
1
S20
F1
F2
F3
F4
Y1
Q1
S1 & S2
S3 & S4
F5
T1
T2
T3
T4
2
3
S24
A1
L
S
I
G
N N
Siemens AG 2011
3WL Air Circuit Breakers
51
Siemens 2012
3WL Air Circuit Breakers/Non-Automatic Air Circuit Breakers up to 6300 A (AC)
Project planning aids
Example of the mode of operation of Zone Selective
Interlocking functionality in power distribution
3VL and 3WL circuit breakers used in various staggered levels
Circuit diagram for a Zone Selective Interlocking functionality with multi-
ple infeed and several outgoing units with 3WL circuit breakers
Zone Selective Interlocking functionality: Connection using a coupling
switch, use of 3WL circuit breakers
More information
Up-to-date information on the Internet at:
www.siemens.com/sentron
SENTRON 3WL
SENTRON 3WL SENTRON 3WL SENTRON 3WL
SENTRON 3WL
SENTRON 3WL SENTRON 3VL
N
S
E
0
_
0
1
8
9
7
3
4
5
6
3
4
5
3
4
5
6
6
3
4
5
6
3
4
5
6
3
4
5
6
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
SENTRON 3WL SENTRON 3WL
SENTRON 3WL
NSE0_01898
3
4
5
6
6 5 1 2 3 4
3
4
5
6
Z
S
I
m
o
d
u
l
e
ZSI module Z
S
I
m
o
d
u
l
e
SENTRON 3WL SENTRON 3WL
SENTRON 3WL
NSE0_01899
3
4
5
6
6 5 1 2 3 4
3
4
5
6
SENTRON 3WL SENTRON 3WL
3
4
5
6
3
4
5
6
Z
S
I
m
o
d
u
l
e
ZSI module
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Z
S
I
m
o
d
u
l
e
Siemens AG 2011
3WL Air Circuit Breakers
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
General data
52
Siemens 2012
Technical specifications
1)
Make-time through activation solenoid for synchronization purposes
(short-time excited) 50 ms.
2)
Maintenance means: replace main contact elements and arc chutes
(see Operating Manual).
3)
Further technical specifications on request.
1)
At U
e
= 220 V DC.
2)
At U
e
= 300 V DC.
3)
At U
e
= 600 V DC.
4)
At U
e
= 1000 V DC.
Sizes II
Type 3WL12 10 3WL12 20 3WL12 40
Rated current I
n
at 40 C
Main conductors A ... 1000 2000 4000
Rated operational voltage U
e
(1000 V version, see Catalog LV 10.1, order code "A05")
V DC ... 600/1000 ... 600/1000 ... 600/1000
Rated insulation voltage U
i
V DC 1000 1000 1000
Rated impulse withstand voltage U
imp
Main current paths
Auxiliary circuits
Control circuits
kV
kV
kV
12
4
2,5
12
4
2,5
12
4
2,5
Isolating function to EN 60947-2 Yes Yes Yes
Permissible ambient temperature
Operation
Storage
C
C
25/+70
40/+70
25/+70
40/+70
25/+70
40/+70
Permissible load
at rear horizontal main circuit
connections
(Cu painted black)
up to 40 C
up to 55 C
up to 60 C
up to 70 C
A
A
A
A
1000
1000
1000
1000
2000
2000
2000
1950
4000
3640
3500
3250
Power loss at I
n
for symmetrical loads
Withdrawable circuit breakers W 280 770 1640
Switching times
Make-time
Opening time
Electrical make-time (through activation solenoid)
1)
Electrical opening time (through shunt release)
Electrical opening time (instantaneous undervoltage release)
ms
ms
ms
ms
ms
35
34
100
73
73
35
34
100
73
73
35
34
100
73
73
Endurance
3)
Mechanical (without maintenance) Operating cycles
Mechanical (with maintenance)
2)
Operating cycles
Electrical (without maintenance) Operating cycles
1000 V version Operating cycles
Electrical (with maintenance)
2)
Operating cycles
10000
15000
6000
1000
15000
10000
15000
6000
1000
15000
10000
15000
4000
1000
15000
Switching frequency
600 V version
1000 V version
1/h
1/h
60
20
60
20
60
20
Mounting position
Degree of protection IP20 without cabinet door, IP41 with door sealing
frame, IP55 with cover
Auxiliary conductors (Cu)
Max. number of
auxiliary conductors cross-
section
(solid/stranded)
Standard connection = strain-relief clamp
Without end sleeve
With end sleeve acc. to DIN 46228 Part 2
With twin end sleeve
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16); 1 2.5 mm
2
(AWG 14)
1 0.5 mm
2
(AWG 20) ... 1 1.5 mm
2
(AWG 16)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Optional connection = tension spring
Without end sleeve
With end sleeve acc. to DIN 46228 Part 2
2 0.5 mm
2
(AWG 20) ... 2 2.5 mm
2
(AWG 14)
2 0.5 mm
2
(AWG 20) ... 2 1.5 mm
2
(AWG 16)
Weights 3-pole
4-pole
Fixed-mounted circuit breakers
Withdrawable circuit breakers
Guide frames
Fixed-mounted circuit breakers
Withdrawable circuit breakers
Guide frames
kg
kg
kg
kg
kg
kg
56
60
31
67
72
37
56
60
31
67
72
37
64
68
45
77
82
54
NSE0_00061 a
30 30
NSE0_00062a
30 30
NSE0_00927a
h
=
m
m
m
a
x
.
and/
or
Sizes II
Type 3WL12
Switching capacity class DC
Short-circuit breaking capacity
Up to 220 V DC
Up to 300 V DC
Up to 600 V DC
Up to 1000 V DC
I
cc
I
cc
I
cc
I
cc
kA
kA
kA
kA
35
30
25
20
Rated short-time withstand current I
cw
0.5 s
1 s
2 s
3 s
kA
kA
kA
kA
--
35
1)
/30
2)
/25
3)
/20
4)
--
--
Siemens AG 2011
3WL Air Circuit Breakers
53
Siemens 2012
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
Characteristic curves
DIGmat S100 characteristic curve
Dimensional drawings
DIGmat S100
DIGmat S100 DIGmat S100 drilling pattern
0,01
0,1
1
10
100
1000
10000
0,1 1 10
N
S
E
0
_
0
1
5
7
8
[
s
]
R= 10 s [B]
2 s [A]
B
A
B
A
R
= 0.4
n R
= 1.0
n
MIN
= 1.25
R I
= 1.5
R I
MAX
= 4
I n
/
n
= 0.4 ... 1.0
= 2 ... 10 s at 6
= 1.25 ... 4
R
R
I
n
R
R
nn
N
S
E
0
_
0
1
5
7
6
AUTO
ON
R2
R1
AUTO
MAN PEAK DIAG
MAIN
MENUE
271
1
3
6
DIG S100
_
+
N
S
E
0
_
0
1
5
7
5
250
1
2
2
1
1
5
257
3,5
Siemens AG 2011
3WL Air Circuit Breakers
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
54
Siemens 2012
Size II, up to 4000 A, fixed-mounted version, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
Standard version
Horizontal connection
Optional connection variants
Front connection (single)
Front connection (double hole)
according to DIN 43673
Vertical connection
4-pole version
1)
Mounting space for removal of the arc chutes.
2)
Arc quenching space " 690 V" circuit breaker facing grounded or non-conductive
surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
Fixing points for mounting the circuit breaker in the system.
11)
Terminal face.
12)
Circuit breaker upper edge, only 1000 V circuit breaker.
14)
Space for electrical auxiliary circuit connections.
15)
Arc quenching space, 300 V circuit breaker facing grounded or non-conductive sur-
faces.
16)
Arc quenching space, 600 V circuit breaker facing grounded or non-conductive sur-
faces.
17)
Arc quenching space, 1000 V circuit breaker (with high arc chute) facing grounded or
non-conductive surfaces.
10
270
85
440
570
5) 4)
1
2
3
,
5
2
7
5
4
4
0
,
5
4
3
7
,
5
NSE0_00633a
82 c
47
d
e
N
S
E
0
_
0
0
6
3
4
d
6
90 130 130 130
40
90 90 90 90
3)
40
2
6
4
2
1
N
S
E
0
0
6
3
5
c
3
5
3
5
11)
13,5
NSE0_02003
150
210
230
45
5,5
127
1
5
0
2
7
5
3
2
7
,
5
4
6
1
,
5
7
6
5
4
1
,
5
a
a
1)
6)
3)
106
4
5
1
,
5
5
1
6 6
0
2
2) 16) 17)
14)
12)
15)
4
4
7
82 c
47
g
f
N
S
E
0
_
0
0
6
3
7
d
6
90 130 130 130
40
90 90 90 90
3)
40 4
0
4
0
1
4
4
2
1
N
S
E
0
0
6
3
8
c
11)
8
0
8
0
13,5
130 90
30 30
130 130
90
3
5
11)
7)
9
7)
460
128 139
590
3) 13,5
N
S
E
0
_
0
0
6
3
9
f
113,5
128,5
1
3
4
,
5
9
8 2
9
0
3
0
3
0
NSE00640b
1
3
,
5
35
11)
90 130 130 130
b
3)
NSE00641
3)
130 130 90 130
NSE00642
Rated
circuit breaker
current
A
a b c d e f g
Up to 2000 10 15 10 11 451 34 541
4000 30 30 20 6 461 39 551
Siemens AG 2011
3WL Air Circuit Breakers
55
Siemens 2012
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
Size II, up to 4000 A, draw-out technology, 3 and 4-pole
For safety clearances to grounded parts and to live parts see
page 38.
For vertical connection and flange connection see following page.
Standard version
Horizontal connection
Optional connection variants
Front connection (single)
Front connection (double hole)
according to DIN 43673
4-pole version
2)
For guide frame 690 V, without arc chute cover, arc quenching space facing
grounded or non-conductive surfaces.
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the system.
4)
Auxiliary connector with SIGUT screw terminals.
5)
Auxiliary connector with spring-loaded connection.
6)
Dimension to inside surface of the closed cabinet door.
7)
3WL circuit breaker in connected position.
8)
3WL circuit breaker in test position.
9)
3WL circuit breaker in disconnected position.
10)
Fixing holes, 10 mm in diameter.
11)
Terminal face.
12)
Guide frame upper edge only 1000 V AC version.
15)
Arc quenching space, 300 V circuit breaker facing grounded or non-conductive
surfaces.
16)
Arc quenching space, 600 V circuit breaker facing grounded or non-conductive
surfaces.
17)
Arc quenching space, 1000 V circuit breaker (with high arc chute) facing grounded or
non-conductive surfaces.
55 350
270
40
480
10) 10)
4
6
5
,
5
1
2
3
,
5
2
7
5
4
6
8
,
5
NSE0_00643b
4) 5)
c
62,5
169,5
1
1
4
0
3
N
S
E
0
0
6
4
4
b
6
55 1 30 1 30 1 30
40
90 90 90 90
3)
45, 1
2
6
3
7
3
40
N
S
E
0
_
0
0
6
4
5
c
3
5
3
5
1 1 )
1 3, 5
400
530
2
8
7
6
9
220 27
42
4
0
3
1
45
6)
88,5
121,5
140,5
58
8)
9)
7
6
3
2
7
,
5
5
1
8
,
5
1
5
0
a
a
2
7
5
4
6
0
5
2
0
6
5
1
4
9
6
327
367,5
382,5
16) 17)
2)
12)
15)
7)
10)
14
9
3)
NSE0_02084
c
62,5
169,5
3
4
4
9
3
N
S
E
0
0
6
4
7
b
6
55 1 30 1 30 1 30 45
40
90 90 90 90
3)
1
4
4
0
4
0
3
7
3
40
N
S
E
0
_
0
0
6
4
8
c
8
0
1 1 )
8
0
1
3
,
5
400
530
2
8
7
6
9
30
138 139
95 270
460
590
30
N
S
E
0
0
6
4
9
a
13,5
3
8
11)
90
400
530
90 90 90
55 45 130 130 130
10)
10)
6
9
2
8
7
N
S
E
0
_
0
0
6
5
2
b
3)
Rated circuit breaker current
A
a b c
Up to 2000 10 10 10
4000 30 30 20
Siemens AG 2011
3WL Air Circuit Breakers
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
56
Siemens 2012
Size II, up to 4000 A, draw-out technology, 3 and 4-pole
4-pole version
3)
Rivels (4 mm wide, 5 mm deep) for supporting phase barriers in the
system.
11)
Terminal face.
For safety clearances to grounded parts and to live parts see
page 38.
For more connection options see previous page.
Vertical connection
Flange connection
157
172
1
3
5
1
0
0
2
9
0
3
0
3
0 N
S
E
0
0
6
5
0
a
38
11)
55 45 1 30 1 30 1 30
b
3)
NSE0_00651 a
400
530
2
8
7
6
9
121
N
S
E
0
0
6
5
3
45 1 30 1 30 1 30
90 40
3)
5
9
5
9
2
6
3
3
2
8
2
,
5
1
4
2
,
5
N
S
E
0
_
0
0
6
5
4
a
M 1 2
400
530
2
8
7
6
9
Siemens AG 2011
3WL Air Circuit Breakers
57
Siemens 2012
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
Circuit diagrams
Circuit diagram of the DIGmat S100 and the 3WL non-automatic air circuit
breaker
Application examples
The connection to the circuit breakers is not dependent on direc-
tion and polarity; the circuit diagrams can be adapted accord-
ingly.
If the parallel or series connections are made directly at the
connecting bars, for thermal reasons the continuous load on the
circuit breakers must only be 80 % of the permissible operational
current. If the parallel or series connection is made at a distance
of 1 m from the connecting bars, the circuit breaker can be used
at full operational current load.
]
Grounded-neutral system
Load
L1
N
PE
AC230
DC24
+
-
X1.2 X1.1 X5.2 X5.1
+
-
DC24
AC230
X4.i1+
X4.i1-
X4.i2+
X4.i2-
DIGmat S100
+
-
X2.1
X2.3
+
-
-Q01 1 3 5
3WL
X4.01
+
X4.01
-
X4.02
+
X4.02
-
X4.03
+
X4.04
+
X4.04
-
X4.03
-
-K1
-K2 11
12 14
11
12
14
-X6.14 -X5.12
SENTRON
-F1 -F3
-X6.13 -X5.11
-Q01 2 4 6
N
S
E
0
_
0
1
5
7
7
a
Emergency STOP
Auxiliary power
Automatic RESET
Shunt
(60mV)
E
x
c
i
t
a
t
i
o
n
/
A
l
a
r
m
A
u
t
o
m
a
t
i
c
/
R
e
s
e
t
Digital output
Digital input
Rated operational
voltage
Required,
series-connected
breaks at
rated voltage
For 3-pole non-automatic air circuit
breakers
(operational currents up to 4000 A/conduct-
ing path)
For 4-pole non-automatic air circuit breakers
(operational currents up to 4000 A/conducting path)
Up to 300 V + 10 %
1-pole,
2 parallel conducting
paths,
only with grounded-
neutral system
2-pole 1-pole,
3 parallel conducting paths,
only with grounded-neutral
system
2-pole
2 parallel conducting
paths
Over 300 V + 10 %
Up to 600 V + 10 %
2-pole,
only with grounded-
neutral system
1-pole,
2 parallel conducting paths,
only with grounded-neutral
system
2-pole
Over 600 V + 10 %
Up to 1000 V + 10 %
(version for 1000 V
required, order with "-Z"
and order code A05)
1-pole,
only with grounded-
neutral system
2-pole,
only with grounded-neutral
system
1-pole,
only with grounded-
neutral system
Siemens AG 2011
3WL Air Circuit Breakers
3WL Non-Automatic Air Circuit Breakers up to 4000 A (DC)
Project planning aids
58
Siemens 2012
More information
Up-to-date information on the Internet at:
www.siemens.com/sentron
Siemens AG 2011
Siemens AG 2011
The information provided in this Configuration Manual contains
descriptions or characteristics of performance which in case of actual
use do not always apply as described or which may change as a result
of further development of the products. An obligation to provide
the respective characteristics shall only exist if expressly agreed in the
terms of contract. Availability and technical specifications are subject to
change without notice.
All product designations may be trademarks or product names
of Siemens AG or supplier companies whose use by third
parties for their own purposes could violate the rights of
the owners. www.siemens.com/lowvoltage
Subject to change without prior notice
PDF only
MP.R3.LV.0000.00.2.92
PH 1111 58 En
Siemens AG 2011
Siemens AG
Infrastructure & Cities Sector
Low and Medium Voltage Division
Low Voltage Distribution
Postfach 10 09 53
93009 REGENSBURG
GERMANY
PH_01_2012_umschlag_en.indd 2 24.11.2011 12:03:16
Siemens AG 2011