Professional Documents
Culture Documents
Quick Start Guide to the VADIS frame V 212x Number of this document: see footer You must always obtain express written permission from KLOTZ DIGITAL before reproducing this documentation in whole or in part. Microsoft and Windows are registered trademarks of Microsoft Corporation. Specifications are subject to change without notice.
KLOTZ DIGITAL AG Headquarters Hans-Stiessberger-Strasse 2A 85540 Haar, Germany Phone: +49-89-45672 300 Fax: +49-89-45672 309 E-mail: mailto:info@klotzdigital.com Web: http://www.klotzdigital.com For information on current addresses, telephone numbers, etc. of our offices abroad, please visit our web site.
V212xQ060817 Specifications are subject to change without notice KLOTZ DIGITAL 2006
Important Information Safety Information Warnings Introduction Intention How to Read Mounting Unpacking
Environment Rack Properties Arrangement Weights and Measures Cabling Cable Types Pinout
Synchronization Audio
Open Cardboard Box Lift Out Check Scope of Delivery Check Interior
4 4 4 4 4 4 5 5
5 5 5 5
5 5 6 6 7 7 8
7 7 8 9
Power Connector 18 Ground Connector 18 Ethernet Connectors for VADIS Control PC / Network 18 GPI Inputs and Outputs 19 CMI AEON Connector, V 212CA/C HDD/CV only 20 CMI Connectors for external CMI Devices, V 212CA/C HDD/CV only 21 Status GPI with 2 Inputs and 1 Output 21 BNC Sync I/O 22 AES Sync Connector 22 VGA Connector, V 212CA/C HDD/CV only 22 Service Keyboard 22 Service Display 23 End User License Agreement (EULA) 25
V 344 Microphone Preamplifier Card, 4 Channels V 618 A/D Interface Card, 8 Channels V 639 D/A Interface Card, 8 Channels V 718 / V 719 AES Input Interface Card, 8 Channels V 738 AES Output Interface Card, 8 Channels V 126/x Fiber Optical Interface Cards, 64 Channels V 292, Serial Data Interface Card, 2 Channels V 2100 DSS Bus Interface Card, 4 Buses, 48 V V 2300 OCTO-BUS Bus Interface Card, 4 Buses, 48 V
9 10 11 12 14 16 16 17 17
24 25
V212xQ060817
Content
Content
Important Information
Important Information
Safety Information
CAUTION
Before you set up and operate your V 212x, read and follow the safety information in your V 212x manual.
Warnings
There is a certain hierarchy of warnings in this guide. The warnings are printed in bold letters and marked by a warning sign at the margin. In the following the warnings are described in detail: The term WARNING will be used wherever danger is imminent. The possible consequences may be death or severe injury (personal injury). The term CAUTION will be used wherever a dangerous situation is possible. The possible consequences include death, severe or light injury (personal injury) damage to property (destruction of modules) or environmental hazards (fire damage). In any case, the failure to observe these instructions will result in the loss of guaranty. The term NOTE will be used for marking recommendations on the use. These sections contain additional information, recommendations, hints and tips. Non-compliance with these recommendations may result in damage to property, e.g. to the system or the software.
WARNING CAUTION
NOTE
Introduction
Intention
This quick start guide is intended for providing the minimum information necessary to install the 19 VADIS frame V 212x. For more detailed information, refer to the V 212x manual. The term V 212x includes the following models: Model V 212 V 212CA V 212CV V 212C HDD Features Fanless, 8 GPI I/Os, to be controlled externally, optional redundant PSU Fanless, 8 GPI I/Os, integrated AEON controller incl. CMI interface, optional redundant PSU Fanless, 8 GPI I/Os, integrated VARIZONE controller incl. CMI interface, optional redundant PSU Fanless, 8 GPI I/Os, integrated HDD controller incl. CMI interface, optional redundant PSU
How to Read
In this guide, the following designations are used: - Quotation marks indicate terms which are used on the VADIS GUI, on the V 212x surface and in MS Windows. Sole exception: headings. - Italics are used for accentuations In this guide the following abbreviations are used: Abbreviation Stands for ... A/D ch ctrl D/A I/F
V212xQ060817
Abbreviation Stands for ... I/O mic preamp pwr sync input / output microphone (microphone) preamplifier power synchronization
KLOTZ DIGITAL 2006
Unpacking
Open Cardboard Box
The V 212x frames are shipped in cardboard boxes lined with Styrofoam parts.
CAUTION
Avoid heavy vibrations and do not reach deep inside the box with your tools, e.g. a knife or box cutter. Open the cardboard box at the top side.
Lift Out
CAUTION
Consider the weight of a V 212x frame when lifting it out of the cardboard box. Depending on the equipment, the weight of the VADIS V 212x can be up to 14 kg.
Check Interior
Check if the V 212x frame's plug-in modules are properly inserted and fixed with 2 or 4 screws, depending on the type of module.
Environment
CAUTION
In order to avoid overheating, the ambient temperature on top of the V 212x cabinet must not exceed 40 C / 104 F! The maximum environmental humidity must not exceed 85%! If you intend to install more than 1 frame per rack, take into consideration that the ambient temperature will probably rise with every additional frame. If necessary, appropriate measures must be taken against overheating.
Rack Properties
CAUTION
It is strongly recommend to mount the V 212x in a 19 rack. The 19 rack must be properly grounded in compliance with IEC safety standards and the regulations of the country it is being used in. The rack must show sufficient stability to carry a V 212x frame *). Telescope or slide rails of sufficient load-carrying capacity must be fitted in order to support the frame *). The rack must be of sufficient depth to cover 100% of the frame depth on the telescope or slide rails *). Simple service and operation of the V 212x frame is only possible if there is free access to the front and back side of the rack. *) The weights and measures of the V 212x can be found under Weights and Measures.
V212xQ060817
Mounting
Mounting
Mounting
Arrangement
CAUTION
When mounting the V 212x frame into a 19 rack, leave at least 1 RU of free space above and below the frame. Otherwise a sufficient cooling of the frame is not provided. The airflow in and out of the V 212x as well as its arrangement within a 19'' rack is shown in figure 1.
OUT
19 device
OU
OUT
IN
19 device
IN
IN
Figure 1: Airflow in (light arrows) and out (dark arrows) of a VADIS frame V 212x, mounted in a rack with other rack mount devices
Cable Types
NOTE! In this guide, the terms "screened twisted pair cable" and "shielded twisted pair cable" are used as follows: Term Screened twisted pair cable Shielded twisted pair cable Meaning The individual pairs of conductors are not shielded. All pairs of conductors are provided with one overall screen or metal foil. Each pair of conductors is individually shielded. An overall screen is not necessary.
The following tables indicate the cable types required for wiring a V 212x.
Synchronization
Audio
Signal Type Remark Analog, mic level Balanced Analog, line level Balanced AES / S/PDIF AES-3 / IEC958 Fiber optics, 1300 nm ANSI X3T9.5 OCTO-BUS / DSS Audio / ctrl / pwr Cable Type 2 cores, twisted to a pair, shielded Screened twisted pair cable V 719 / V 738: AES 75 / 110 50/125 m / 62,5/125 m, Multi Mode Cat 5 / J-Y(ST)Y
V212xQ060817
Cabling
Cabling
Cabling
Pinout
Survey of the V 212x Rear Side Connectors
Power socket Fuse Ground connector
Disconnect power before removing cover or any screws. 150 Watt Power Supply 115-230 VAC / 60 - 50 Hz 2.5 - 1.2 A Fuse 2.5 A SB
AES OUT 8
DSP
D/A 8
D/A 8
A/D 8
A/D 8
AES IN 8
Ethernet connectors for VADIS control PC / network, V 212CA/C HDD/CV only GPI, 8 inputs, 8 outputs CMI AEON connector, V 212CA/C HDD/CV only CMI connectors for external CMI devices, V 212CA/C HDD/CV only Ethernet / CMI link indicator LEDs, V 212CA/C HDD/CV only Status GPI, 2 inputs, 1 output BNC sync inputs / outputs Ethernet connector for VADIS control PC / network, V 212 only Ethernet link indicator LEDs, V 212 only
AES SYNC
ETH
ETH
CMI 2
200
CMI 1
CMI 3
Serial No.:
WCLK 75
Status GPI
GPI
AES sync connector VGA connector, V 212CA/C HDD/CV only Cover plate for integrated PC connectors, V 212CA/C HDD/CV only, to be removed for service purposes only
PUSH
Figure 2: V 212x rear view Below, basics about the V 212x connectors are described. For more details, refer to the V 212x manual.
V212xQ060817 Specifications are subject to change without notice KLOTZ DIGITAL 2006
Please refer to the V 212x manual for interface card pinouts not listed below.
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Channel 4 ground/shield Channel 4 - input Channel 4 + input Channel 3 ground/shield Channel 3 ground/shield Channel 3 - input Channel 3 + input Channel 2 ground/shield Channel 2 ground/shield Channel 2 - input Channel 2 + input Channel 1 ground/shield Channel 1 ground/shield Channel 1 - input Channel 1 + input
V212xQ060817
Cabling
Interface Cards
10
Cabling
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Ground/shield input 4 Input 4Input 4+ Ground/shield input 3 Ground/shield input 3 Input 3Input 3+ Ground/shield input 2 Ground/shield input 2 Input 2Input 2+ Ground/shield input 1 Ground/shield input 1 Input 1Input 1+
Connector 2
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Ground/shield input 8 Input 8Input 8+ Ground/shield input 7 Ground/shield input 7 Input 7Input 7+ Ground/shield input 6 Ground/shield input 6 Input 6Input 6+ Ground/shield input 5 Ground/shield input 5 Input 5Input 5+
V212xQ060817
11
9 10 11 12 13 14 15
1 2 3 4 5 6 7 8
Output 1+ Output 1Ground/shield Output 2+ Output 2Ground/shield Output 3+ Output 3Ground/shield Output 4+ Output 4Ground/shield
Connector 2
1 2 3 4 5 6 7 8
9 11 1013 11 15 12 13 14 15
12 14
10
1 2 3 4 5 6
Output 5+ Output 5Ground/shield Output 6+ Output 6Ground/shield Output 7+ Output 7Ground/shield Output 8+ Output 8Ground/shield
= Internally connected
V212xQ060817
Cabling
12
Cabling
J4-J11
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Ground/shield AES in 4AES in 4+ Ground Ground/shield AES in 3AES in 3+ Ground Ground/shield AES in 2AES in 2+ Ground Ground/shield AES in 1AES in 1+
Connector 2
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Ground/shield AES in 8AES in 8+ Ground Ground/shield AES in 7AES in 7+ Ground Ground/shield AES in 6AES in 6+ Ground Ground/shield AES in 5AES in 5+
V212xQ060817
13
Termination: 75
75 J4-J11
15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
AES3-id/S/PDIF in 4 ground AES3-id/S/PDIF in 4+ AES3-id/S/PDIF in 3 ground AES3-id/S/PDIF in 3+ AES3-id/S/PDIF in 2 ground AES3-id/S/PDIF in 2AES3-id/S/PDIF in 1 ground AES3-id/S/PDIF in 1+
Connector 2
15 14 13 12 11 10 9 15 14 13 12 11 10 9
8 7 6 5 4 3 2 18 7 6 5 4 3
AES3-id/S/PDIF in 8 ground AES3-id/S/PDIF in 8+ AES3-id/S/PDIF in 7 ground AES3-id/S/PDIF in 7+ AES3-id/S/PDIF in 6 ground AES3-id/S/PDIF in 6+ AES3-id/S/PDIF in 5 ground AES3-id/S/PDIF in 5+
= To be connected externally
2 1
V212xQ060817
Cabling
14
Cabling
110 J4-J19
9 10 11 12 13 14 15
1 2 3 4 5 6 7 8
AES out 1+ AES out 1Ground/shield Ground AES out 2+ AES out 2Ground/shield Ground AES out 3+ AES out 3Ground/shield Ground AES out 4+ AES out 4Ground/shield
Connector 2
9 10 11 12 13 14 15
1 2 3 4 5 6 7 8
AES out 5+ AES out 5Ground/shield Ground AES out 6+ AES out 6Ground/shield Ground AES out 7+ AES out 7Ground/shield Ground AES out 8+ AES out 8Ground/shield
V212xQ060817
15
Termination: 75
75
J4-J19
9 10 11 12 13 14 15
1 2 3 4 5 6 7 8
AES3-id out 1+ AES3-id out 1 ground AES3-id out 2+ AES3-id out 2 ground AES3-id out 3+ AES3-id out 3 ground AES3-id out 4+ AES3-id out 4 ground
Connector 2
9 10 11 12 13 14 159 10 11 12 13 14 15
1 2 3 4 5 6 71 82 3 4 5 6 7
AES3-id out 5+ AES3-id out 5 ground AES3-id out 6+ AES3-id out 6 ground AES3-id out 7+ AES3-id out 7 ground AES3-id out 8+ AES3-id out 8 ground
= To be connected externally
8
V212xQ060817
Cabling
AES3-id Signals
16
Cabling
1 J4
1 2 3 4 5 6 7 8 9
RS232 master mode DCD (Input) RXD (Input) TXD (Output) DTR (Output) GND DSR (Input) RTS (Output) CTS (Input) RI (Input) RS232 master mode DCD (Input) RXD (Input) TXD (Output) DTR (Output) GND DSR (Input) RTS (Output) CTS (Input) RI (Input)
RS232 slave mode DCD (Output) TXD (Output) RXD (Input) DSR (Input) GND DTR (Output) CTS (Input) RTS (Output) RI (Output) RS232 slave mode DCD (Output) TXD (Output) RXD (Input) DSR (Input) GND DTR (Output) CTS (Input) RTS (Output) RI (Output)
RS422 master mode TXD- (Output) TXD+ (Output) RXD+ (Input) RXD- (Input) GND RTS- (Output) RTS+ (Output) CTS+ (Input) CTS- (Input) RS422 master mode TXD- (Output) TXD+ (Output) RXD+ (Input) RXD- (Input) GND RTS- (Output) RTS+ (Output) CTS+ (Input) CTS- (Input)
RS422 slave mode RXD- (Input) RXD+ (Input) TXD+ (Output) TXD- (Output) GND CTS- (Input) CTS+ (Input) RTS+ (Output) RTS- (Output) RS422 slave mode RXD- (Input) RXD+ (Input) TXD+ (Output) TXD- (Output) GND CTS- (Input) CTS+ (Input) RTS+ (Output) RTS- (Output)
2 J3
1 2 3 4 5 6 7 8 9
V212xQ060817
17
Pin 1 2 3 4 5 6 7 8
Signal TX+ TXRX+ GND line interface GND redundant line interface RX+48 V line interface +48 V redundant line interface
The 2 wires in each pair of the cable connected to the V 2100 card connector must be twisted as follows: Pins / wires 1 and 2 3 and 6 4 and 5 7 and 8 Signals TXD+ and TXDRXD+ and RXDGND and GND +48 V and +48 V
Connector Bus J2 J4 J5 J6
V 2100
1 2 3 4
DSS2-BUS I/O
Installation
The installation of the DSS bus is too extensive to be described here. For details, please see the VARIZONE installation guide.
V212xQ060817
Cabling
18
Cabling
Power Connector
Frame connector: 3-pin male built-in power connector
N L Pin N L PE Signal Neutral conductor Phase conductor Equipment grounding conductor
PE
Ground Connector
The ground connector is a ground bolt.
Link
CMI
CMI
The 2 wires in each pair of the cable connected to the Ethernet connectors for VADIS control network / PC must be twisted as follows: Pins / wires 1 and 2 3 and 6 Signals TX+ and TXRX+ and RX-
V212xQ060817
19
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Signal +5 V GPI input 1 opto-coupler 1+ GPI input 2 opto-coupler 2+ GPI input 3 opto-coupler 3+ GPI input 4 opto-coupler 4+ GPI input 5 opto-coupler 5+ GPI input 6 opto-coupler 6+ GPI input 7 opto-coupler 7+ GPI input 8 opto-coupler 8+ +5 V GPI output 1 relay A GPI output 2 relay A GPI output 3 relay A GPI output 4 relay A GPI output 5 relay A GPI output 6 relay A GPI output 7 relay A GPI output 8 relay A GND GPI input 1 opto-coupler 1GPI input 2 opto-coupler 2GPI input 3 opto-coupler 3GPI input 4 opto-coupler 4GPI input 5 opto-coupler 5GPI input 6 opto-coupler 6GPI input 7 opto-coupler 7GPI input 8 opto-coupler 8GND GPI output 1 relay B GPI output 2 relay B GPI output 3 relay B GPI output 4 relay B GPI output 5 relay B GPI output 6 relay B GPI output 7 relay B GPI output 8 relay B GND
V212xQ060817
Cabling
20
Cabling
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Signal +12 V CMI L CMI L Not used +12 V GND GND GND +12 V CMI H CMI H +12 V +12 V GND GND
The 2 wires in each pair of the cable connected to the CMI AEON connector must be twisted as follows: CMI L and CMI H +12 V and GND
V212xQ060817
21
Link
CMI
CMI
The 2 wires in each pair of the cable connected to the CMI connectors for external CMI devices must be twisted as follows: Pins / wires 1 and 2 3 and 6 4 and 5 7 and 8 Signals CMI H and CMI L GND and GND CMI H and CMI L +12 V and +12 V
Pin 1 2 3 4 5 6 7 8 9
Signal +5 V GPI input 1 opto-coupler 1+ GPI input 2 opto-coupler 2+ GPI output 1 relay A GND GPI input 1 opto-coupler 1GPI input 2 opto-coupler 2+5 V GPI output 1 relay B
V212xQ060817
Cabling
CMI Connectors for external CMI Devices, V 212CA/C HDD/CV only Status TX/RX
22
Cabling
Outer contact
2
3
Service Keyboard
CAUTION
The service keyboard must be used by qualified personnel only. Carrying out service works by unqualified may cause damages to the frame. NOTE The service keyboard PS2 connector is located at the frame's front side! The PS2 connector for a service keyboard is located next to the battery behind the metal plate covering the frame's LCD display and the LEDs. This PS2 connector is used to connect a keyboard to carry out service works concerning the hardware.
V212xQ060817
23
CAUTION
The service display must be used by qualified personnel only. Carrying out service works by unqualified may cause damages to the frame. NOTE The service display IDC connector is located at the frame's front side! The 20-pin IDC connector for a service display is located next to the PS2 service keyboard connector behind the metal plate covering the LCD display and the LEDs. This IDC connector is used to connect a display to carry out service works concerning the hardware.
V212xQ060817
Cabling
Service Display
24
Status Indication
Status Indication
On the V 212x front panel, the frame parameters are indicated via a 2-line LCD display and 5 LEDs. This is outlined on the following table. Parameter
ERROR PSU OK
LEFT RIGHT
Indication LCD display LCD display LCD display LEDs "ERROR", "WARNING", "RUN" "PSU OK" LEDs "LEFT" and "RIGHT" LCD display
WARNING RUN
Frame number Frame name IPX/SPX frame address Frame status PSU status Errors and annoyances
Table 4: V 212x parameters indicated on the front panel For details on the frame parameters and their indication via the LCD display and the LEDs, refer to the V 212x manual.
V212xQ060817
25
Status Indication
Appendix 1
26
der this EULA only as part of a permanent sale or transfer of the DEVICE, provided you retain no copies of the SOFTWARE. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE. This transfer must also include the Certificate of Authenticity label. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end user receiving the SOFTWARE must agree to all the EULA terms. Consent to Use of Data. You agree that MS, Microsoft Corporation and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft Corporation and their affiliates may use this information solely to improve their products or to provide customized services or technologies to you. MS, Microsoft Corporation and their affiliates may disclose this information to others, but not in a form that personally identifies you. Internet Gaming/Update Features. If the SOFTWARE provides, and you choose to utilize, the Internet gaming or update features within the SOFTWARE, it is necessary to use certain computer system, hardware, and software information to implement the features. By using these features, you explicitly authorize MS, Microsoft Corporation and/or their designated agent to use this information solely to improve their products or to provide customized services or technologies to you. MS or Microsoft Corporation may disclose this information to others, but not in a form that personally identifies you. Internet-Based Services Components. The SOFTWARE may contain components that enable and facilitate the use of certain Internet-based services. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may automatically check the version of the SOFTWARE and/or its components that you are utilizing and may provide upgrades or supplements to the SOFTWARE that may be automatically downloaded to your DEVICE. Microsoft Corporation or their affiliates do not use these features to collect any information that will be used to identify you or contact you. For more information about these features, please see the privacy statement at http://go.microsoft.com/fwlink/?LinkId=25243. Links to Third Party Sites. You may link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS or Microsoft Corporation, and MS or Microsoft are not responsible for the contents of any third party sites, any links contained in third party sites, or any changes or updates to third party sites. MS or Microsoft Corporation is not responsible for webcasting or any other form of transmission received from any third party sites. MS or Microsoft Corporation are providing these links to third party sites to you only as a convenience, and the inclusion of any link does not imply an endorsement by MS or Microsoft Corporation of the third party site. Notice Regarding Security. To help protect against breaches of security and malicious software, periodically back up your data and system information, use security features such as firewalls, and install and use security updates. No Rental/Commercial Hosting. You may not rent, lease, lend or provide commercial hosting services with the SOFTWARE to others. Separation of Components. The SOFTWARE is licensed as a single product. Its component parts may not be separated for use on more than one computer. Additional Software/Services. This EULA applies to updates, supplements, add-on components, product support services, or Internet-based services components (Supplemental Components), of the SOFTWARE that you may obtain from KLOTZ, MS, Microsoft Corporation or their subsidiaries after the date you obtain your initial copy of the SOFTWARE, unless you accept updated terms or another agreement governs. If other terms are not provided along with such Supplemental Components and the Supplemental Components are provided to you by MS, Microsoft Corporation or their subsidiaries then you will be licensed by such entity under the same terms and conditions of this EULA, except that (i) MS, Microsoft Corporation or their subsidiaries providing the Supplemental Components will be the licensor with respect to such Supplemental Components in lieu of the COMPANY for the purposes of the EULA, and (ii) TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE SUPPLEMENTAL COMPONENTS AND ANY (IF ANY) SUPPORT SERVICES RELATED TO THE SUPPLEMENTAL COMPONENTS ARE PROVIDED AS IS AND WITH ALL FAULTS. ALL OTHER DISCLAIMERS, LIMITATION OF DAMAGES, AND SPECIAL PROVISIONS PROVIDED BELOW AND/OR OTHERWISE WITH THE SOFTWARE SHALL APPLY TO SUCH SUPPLEMENTAL COMPONENTS. MS, Microsoft Corporation or their subsidiaries reserve the right to discontinue any Internet-based services provided to you or made available to you through the use of the SOFTWARE. Recovery Media. If SOFTWARE is provided by KLOTZ on separate media and labeled Recovery Media you may use the Recovery Media solely to restore or reinstall the SOFTWARE originally installed on the DEVICE. Backup Copy. You may make one (1) backup copy of the SOFTWARE. You may use this backup copy solely for your archival purposes and to reinstall the SOFTWARE on the DEVICE. Except as expressly proSpecifications are subject to change without notice KLOTZ DIGITAL 2006
Status Indication
V212xQ060817
27
vided in this EULA or by local law, you may not otherwise make copies of the SOFTWARE, including the printed materials accompanying the SOFTWARE. You may not loan, rent, lend or otherwise transfer the backup copy to another user. End User Proof of License. If you acquired the SOFTWARE on a DEVICE, or on a compact disc or other media, a genuine Microsoft Proof of License/Certificate of Authenticity label with a genuine copy of the SOFTWARE identifies a licensed copy of the SOFTWARE. To be valid, the label must be affixed to the DEVICE, or appear on KLOTZs software packaging. If you receive the label separately other than from KLOTZ, it is invalid. You should keep the label on the DEVICE or packaging to prove that you are licensed to use the SOFTWARE. Product Support. Product support for the SOFTWARE is not provided by MS, Microsoft Corporation, or their affiliates or subsidiaries. For product support, please refer to KLOTZ support number provided in the documentation for the DEVICE. Should you have any questions concerning this EULA, or if you desire to contact KLOTZ for any other reason, please refer to the address provided in the documentation for the DEVICE. Termination. Without prejudice to any other rights, KLOTZ may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE and all of its component parts. EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. and European Union export jurisdiction. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information see http:// www.microsoft.com/exporting/
V212xQ060817
Status Indication
28
Status Indication
V212xQ060817