You are on page 1of 20

TC14433/A

3-1/2 Digit, Analog-to-Digital Converter


Features
Accuracy: 0.05% of Reading 1 Count Two Voltage Ranges: 1.999V and 199.9 mV Up to 25 Conversions Per Second ZIN > 1000M Ohms Single Positive Voltage Reference Auto-Polarity and Auto-Zero Overrange and Underrange Signals Available Operates in Auto-Ranging Circuits Uses On-Chip System Clock or External Clock Wide Supply Range: 4.5V to 8V

Package Type
24-Pin PDIP (Wide) 24-Pin CERDIP (Wide) 24-Pin SOIC (Wide)
VAG VREF VX 1 2 3 24 VDD 23 Q3 22 Q2 21 Q1

R1 4 R1/C1 5

TC14433/A

20 Q0 19 DS1 18 DS2 17 DS3 16 DS4 15 OR 14 EOC 13 VSS

C1 6 CO1 7

Applications
Portable Instruments Digital Voltmeters Digital Panel Meters Digital Scales Digital Thermometers Remote A/D Sensing Systems MPU Systems

CO2 8 DU 9

CLK1 10 CLK0 11

VEE 12

Device Selection Table


Part Number TC14433AEJG TC14433AELI TC14433AEPG TC14433COG TC14433EJG TC14433ELI TC14433EPG Package 24-Pin CERDIP (Wide) 28-Pin PLCC 24-Pin PDIP (Wide) 24-Pin SOIC (Wide) 24-Pin CERDIP (Wide) 28-Pin PLCC 24-Pin PDIP (Wide) Temperature Range -40C to +85C
R1 5 VX

28-Pin PLCC
VREF VAG VDD NC Q3 Q2 25 Q1 24 Q0 23 DS1 22 NC 21 DS2 20 DS
3

28 27 26

-40C to +85C -40C to +85C 0C to +70C -40C to +85C -40C to +85C -40C to +85C

R1/C1 6 C1 7 NC 8 CO1 9 CO2 10 DU 11 12 13 14 15 16 17 18 EOC CLK1 CLK0 VEE VSS NC OR

TC14433/A

19 DS4

Note 1: NC = No internal connection (In 28-Pin PLCC). 2: 24-Pin SOIC (Wide) package, only for TC14433 device.

2002 Microchip Technology Inc.

DS21394B-page 1

TC14433/A
General Description
The TC14433 is a low power, high performance, monolithic CMOS 3-1/2 digit A/D converter. The TC14433 combines both analog and digital circuits on a single IC, thus minimizing the number of external components. This dual slope A/D converter provides automatic polarity and zero correction with the addition of two external resistors and two capacitors. The full scale voltage range of this ratiometric IC extends from 199.9 millivolts to 1.999 volts. The TC14433 can operate over a wide range of power supply voltages, including batteries and standard 5-volt supplies. The TC14433A features improved performance over the industry standard TC14433. Rollover, which is the measurement of identical positive and negative signals, is specified to have the same reading within one count for the TC14433A. Power consumption of the TC14433A is typically 4mW, approximately onehalf that of the industry standard TC14433. The TC14433/A is available in 24-Pin PDIP, 24-Pin CERDIP, 24-Pin SOIC (TC14433 device only), and 28-Pin PLCC packages.

Typical Application
MCP1525 +5V VIN VOUT VSS 1F VX R1* 20k 1F 300k RC 11 10 2 12 24 23 22 21 4 20 TC14433 5 6 13 3 1 7 8 9 14 15 19 18 17 16 +5V 0.1 -5V +5V 0.1F 1 4 2 3 5 -5V 16 7 6 5 4 3 2 1 -5V -5V 10 11 12 13 14 15 16 1413 Minus Sign f g e d c b a 9 10 11 12 13 4543B 14 15 8 6 7 +5V Segment Resistors 150 (7)

0.1F** 0.1F**

-5V -5V 6 5 S 1 Q 2 3 D C RQ 4 8 9 D S Q 13 11 C Q 12 R 710 14 +5V

*R1 = 470k for 2V Range R1 = 27k for 200mV Range **Mylar Capacitor 14013B

200 MPS-A12 Plus Sign -5V 110 51k Common Anode Led +5V Display 50F 0.1F MPS-A12 (4) -5V

DS4 DS3 DS2 DS1

-5V

DS21394B-page 2

2002 Microchip Technology Inc.

TC14433/A
1.0 ELECTRICAL CHARACTERISTICS
*Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.

Absolute Maximum Ratings*


Supply Voltage (V DD VEE) ................... -0.5V to +18V Voltage on Any Pin: Reference to VEE .....................-0.5V to (VDD + 0.5) DC Current, Any Pin: ........................................ 10mA Power Dissipation (TA 70C): Plastic PLCC ................................................. 1.0W Plastic PDIP.................................................. 940W SOIC ............................................................. 940W CERDIP ....................................................... 1.45W Operating Temperature Range ............... 0C to +70C Storage Temperature Range .............. -65C to +160C

TC14433/A ELECTRICAL SPECIFICATIONS


Electrical Characteristics: VDD = +5V, VEE = -5V, C1 = 0.1F, (Mylar), C 0 = 0.1F, RC = 300k, R1 = 470k @ VREF = 2V, R1 = 27k @ VREF = 200mV, unless otherwise specified. Symbol Analog Input SYE Rollover Error (Positive) and Negative Full Scale Symmetry Linearity Output Reading (Note 1) Stability Output Reading (Note 2) -1 Parameter Min Typ TA = +25C +1 Max Min Typ TA = +25C Counts 200mV Full Scale VIN -VIN = +VIN %rdg %rdg LSD LSD LSD pA pA pA dB VX = 1.4V, VREF = 2V, FOC = 32kHz VREF = 2V VREF = 200mV VX = 1.99V, VREF = 2V VX = 199mV, VREF = 200mV VX = 0V, VREF = 2V Max Units Test Conditions

NL SOR

-0.05 -1 count

+0.05 0 20 20 20 65

+0.05 +1 count 2 3 0 100 100 100

ZOR IIN

Zero Output Reading Bias Current: Analog Input Reference Input Analog Ground

CMRR

Common mode Rejection

Note 1: Accuracy - The accuracy of the meter at full scale is the accuracy of the setting of the reference voltage. Zero is recalculated during each conversion cycle. The meaningful specification is linearity. In other words, the deviation from correct reading for all inputs other than positive full scale and zero is defined as the linearity specification. 2: The LSD stability for 200mV scale is defined as the range that the LSD will occupy 95% of the time. 3: Pin numbers refer to 24-pin PDIP.

2002 Microchip Technology Inc.

DS21394B-page 3

TC14433/A
TC14433/A ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: VDD = +5V, VEE = -5V, C1 = 0.1F, (Mylar), C 0 = 0.1F, RC = 300k, R1 = 470k @ VREF = 2V, R1 = 27k @ VREF = 200mV, unless otherwise specified. Symbol Digital VOL Output Voltage (Pins 14 to 23) (Note 3) Output Voltage (Pins 14 to 23) (Note 3) Output Current (Pins 14 to 23) VOH 4.95 4.95 IOH -0.2 - 0.5 IOL Output Current (Pins 14 to 23) 0.51 1.3 fCLK IDU Power IQ Quiescent Current: 14433A: Quiescent Current: 14433: PSRR Supply Rejection 0.4 1.4 0.9 1.8 0.5 2 4 2 4 3.7 7.4 3.7 7.4 mA mA mA mA mV/V VDD to VEE, ISS = 0 VDD = 5, VEE = -5 VDD = 8, VEE = -8 VDD to VEE, ISS = 0 VDD = 5, VEE = -5 VDD = 8, VEE = -8 VDD to VEE, ISS = 0, VREF = 2V, VDD = 5, VEE = -5 Clock Frequency Input Current -DU 0 -5 5 5 -0.36 -0.9 0.88 2.25 66 0.00001 0.05 -4.95 0.3 4.95 4.95 -0.14 -0.35 0.36 0.9 0.05 -4.95 1 V V V V mA mA mA mA kHz A VSS = 0 V, "0" Level VSS = -5V, "0" Level VSS = 0V, "1" Level VSS = -5V, "1" Level VSS = 0V, VOH = 4.6V Source VSS = -5V, VOH = 5V Source VSS = 0V, VOL = 0.4V Sink VSS = -5V, VOL = -4.5V Sink RC = 300k Parameter Min Typ Max Min Typ Max Units Test Conditions

Note 1: Accuracy - The accuracy of the meter at full scale is the accuracy of the setting of the reference voltage. Zero is recalculated during each conversion cycle. The meaningful specification is linearity. In other words, the deviation from correct reading for all inputs other than positive full scale and zero is defined as the linearity specification. 2: The LSD stability for 200mV scale is defined as the range that the LSD will occupy 95% of the time. 3: Pin numbers refer to 24-pin PDIP.

DS21394B-page 4

2002 Microchip Technology Inc.

TC14433/A
2.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2.0.

TABLE 2-1:
Pin No. (24-Pin PDIP) (24-Pin CERDIP) (24-Pin SOIC) 1 2

PIN FUNCTION TABLE


Pin No. Symbol (28-Pin PLCC) 2 3 VAG VREF Description

This is the analog ground. It has a high input impedance. The pin determines the reference level for the unknown input voltage (VX) and the reference voltage (VREF). Reference voltage - Full scale output is equal to the voltage applied to VREF. Therefore, full scale voltage of 1.999V requires 2V reference and 199.9mV full scale requires a 200mV reference. VREF functions as system reset also. When switched to VEE, the system is reset to the beginning of the conversion cycle. The unknown input voltage (VX) is measured as a ratio of the reference voltage (VREF ) in a rationetric A/D conversion. This pin is for external components used for the integration function in the dual slope conversion. Typical values are 0.1F (mylar) capacitor for C 1. R1 = 470k (resistor) for 2V full scale. R1 = 27k (resistor) for 200mV full scale. Clock frequency of 66kHz gives 250msec conversion time. These pins are used for connecting the offset correction capacitor. The recommended value is 0.1 F. These pins are used for connecting the offset correction capacitor. The recommended value is 0.1 F. Display update input pin. When DU is connected to the EOC output, every conversion is displayed. New data will be strobed into the output latches during the conversion cycle if a positive edge is received on DU, prior to the ramp down cycle. When this pin is driven from an external source, the voltage should be referenced to VSS. Clock input pins. The TC14433 has its own oscillator system clock. Connecting a single resistor between CLK1 and CLK0 sets the clock frequency. A crystal or OC circuit may be inserted in lieu of a resistor for improved CLK1 , the clock input, can be driven from an external clock source, which need only have standard CMOS output drive. This pin is referenced to VEE for external clock inputs. A 300k resistor yields a clock frequency of about 66kHz. See Section 5.0 Typical Characteristics. (Also see Figure 4-3 for alternate circuits.) Negative power current. Connection pin for the most negative supply. Please note the current for the output drive circuit is returned through VSS. Typical supply current is 0.8mA. Negative power supply for output circuitry. This pin sets the low voltage level for the output pins (BCD, Digit Selects, EOC, OR). When connected to analog ground, the output voltage is from analog ground to VDD. If connected to VEE, the output swing is from VEE to VDD. The recommended operating range for VSS is between the VDD -3 volts and VEE. End of conversion output generates a pulse at the end of each conversion cycle. This generated pulse width is equal to one half the period of the system clock. Overrange pin. Normally this pin is set high. When VX exceeds VREF the OR is low. Digit select pin. The digit select output goes high when the respective digit is selected. The MSD (1/2 digit turns on immediately after an EOC pulse). The remaining digits turn on in sequence from MSD to LSD. To ensure that the BCD data has settled, an inter digit blanking time of two clock periods is included. Clock frequency divided by 80 equals multiplex rate. For example, a system clock of 60kHz gives a multiplex rate of 0.8kHz. See Figure 4-4 for digit select timing diagram.

3 4 5 6 7 8 9

4 5 6 7 9 10 11

VX R1 R1/C1 C1 CO1 CO2 DU

10 11

12 13

CLK1 CLK0

12

14

V EE

13

16

V SS

14 15 16 17 18 19 20

17 18 19 20 21 23 24

EOC OR DS4 DS3 DS2 DS1 Q0

2002 Microchip Technology Inc.

DS21394B-page 5

TC14433/A
TABLE 2-1:
Pin No. (24-Pin PDIP) (24-Pin CERDIP) (24-Pin SOIC) 21 22 23 24

PIN FUNCTION TABLE (CONTINUED)


Pin No. Symbol (28-Pin PLCC) 25 26 27 28 1 8 15 22 Q1 Q2 Q3 VDD NC NC NC NC Description

BCD data output pin. Multiplexed BCD outputs contain three full digits of information during digit select DS2, DS3, DS4. During DS1, the 1/2 digit, overrange, underrange and polarity information is available. Refer to the Truth Table 4-1. Positive power supply. This is the most positive power supply pin. Not Used. Not Used. Not Used. Not Used.

DS21394B-page 6

2002 Microchip Technology Inc.

TC14433/A
3.0 DETAILED DESCRIPTION
The TC14433 CMOS IC becomes a modified dualslope A/D with a minimum of external components. This IC has the customary CMOS digital logic circuitry, as well as CMOS analog circuitry. It provides the user with digital functions such as (counters, latches, multiplexers), and analog functions such as (operational amplifiers and comparators) on a single chip. Refer to the Functional Block diagram, Figure 3-3 Features of the TC14433/A include auto-zero, high input impedances and auto-polarity. Low power consumption and a wide range of power supply voltages are also advantages of this CMOS device. The system's auto-zero function compensates for the offset voltage of the internal amplifiers and comparators. In this "ratiometric system," the output reading is the ratio of the unknown voltage to the reference voltage, where a ratio of 1 is equal to the maximum count of 1999. It takes approximately 16,000 clock periods to complete one conversion cycle. Each conversion cycle may be divided into 6 segments. Figure 3-1 shows the conversion cycle in 6 segments for both positive and negative inputs. Segment 1 - The offset capacitor (CO), which compensates for the input offset voltages of the buffer and integrator amplifiers, is charged during this period. However, the integrator capacitor is shorted. This segment requires 4000 clock periods. Segment 2 - During this segment, the integrator output decreases to the comparator threshold voltage. At this time, a number of counts equivalent to the input offset voltage of the comparator is stored in the offset latches for later use in the auto-zero process. The time for this segment is variable and less than 800 clock periods. Segment 3 - This segment of the conversion cycle is the same as Segment 1. Segment 4 - Segment 4 is an up going ramp cycle with the unknown input voltage (VX as the input to the integrator. Figure 4-2 shows the equivalent configuration of the analog section of the TC14433. The actual configuration of the analog section is dependent upon the polarity of the input voltage during the previous conversion cycle.

FIGURE 3-2:

FIGURE 3-1:

INTEGRATOR WAVEFORMS AT PIN 6


End 2 3 4 5 6 VX Typical Positive Input Voltage Buffer VX +

EQUIVALENT CIRCUIT DIAGRAMS OF THE ANALOG SECTION DURING SEGMENT 4 OF THE TIMING CYCLE
C1 R1 Integrator + Comparator +

Start Time 1 Segment Number

VX

Typical Negative Input Voltage

Segment 5 - This segment is a down-going ramp period with the reference voltage as the input to the integrator. Segment 5 of the conversion cycle has a time equal to the number of counts stored in the offset storage latches during Segment 2. As a result, the system zeros automatically. Segment 6 - This is an extension of Segment 5. The time period for this portion is 4000 clock periods. The results of the A/D conversion cycle are determined in this portion of the conversion cycle.

2002 Microchip Technology Inc.

DS21394B-page 7

TC14433/A
FIGURE 3-3: FUNCTIONAL BLOCK DIAGRAM
20-23 RC 10 11 CLK1 CLK0 Clock 1's Multiplexer 16 -19 Q Q3 BDC Data DS1 DS4 Digit Strobe Polarity Detect 100's 1,000's

Latches 10's

TC14433/A
Overflow

15

OR Overrange VREF Reference Voltage VAG Analog Ground Analog Input VX VDD = Pin 24 VSS = Pin 13 VEE = Pin 12

Control Logic

CMOS Analog Subsystem 4 5 R1 R1/C 6 7 8 C1 CO1 CO2 Offset

2 1 3

Display Update

End of 9 14 Conversion DU EOC

Integrator

DS21394B-page 8

2002 Microchip Technology Inc.

TC14433/A
4.0 TYPICAL APPLICATIONS
Note: If the most significant digit is connected to a display other than a "1" only, such as a full digit display, segments other than b and c must be disconnected. The BCD to 7-segment decoder must blank on BCD inputs 1010 to 1111. See Table 4-1 The Typical Application circuit is an example of a 3-1/2 digit voltmeter using the TC14433 with Commonanode displays. This system requires a 2.5V reference. Full scale may be adjusted to 1.999V or 199.9 mV. Input overrange is indicated by flashing a display. This display uses LEDs with common anode digit lines. Power supply for this system is shown as a dual 5V supply; however, the TC14433 will operate over a wide voltage range The circuit in Figure 4-1 shows a 3-1/2 digit LCD voltmeter. The 14024B provides the low frequency square wave signal drive to the LCD backplane. Dual power supplies are shown here; however, one supply may be used when VSS is connected to VEE. In this case, VAG must be at least 2.8V above VEE. When only segments b and c of the decoder are connected to the 1/2 digit of the display, 4, 0, 7 and 3 appear as 1. The overrange indication (Q 3 = 0 and Q0 = 1) occurs when the count is greater than 1999; (e.g., 1.999V for a reference of 2V) The underrange indication, useful for auto-ranging circuits, occurs when the count is less than 180; (e.g., 0.180V for a reference of 2V).

TABLE 4-1:
Coded Q Condition 3 of MSD +0 -0 +0 UR -0 UR +1 -1 +1 OR -1 OR
Note 1:

TRUTH TABLE
Q
2

Q
1

Q
0

BDC to 7-Segment Decoding Blank Blank Blank Blank 41 01 71 31 Hook up only segments b and c to MSD

1 1 1 1 0 0 0 0

1 0 1 0 1 0 1 0

1 1 1 1 0 0 1 1

0 0 1 1 0 0 1 1

Q3 - 1/2 digit, low for "1", high for "0". Q2 - Polarity: "1" = positive, "0" = negative. Q0 - Out of range condition exists if Q0 = 1. When used in conjunction with Q3, the type of out of range condition is indicated; i.e., Q3 = 0 OR or Q3 = 1 UR.

Figure 4-2 is an example of a 3-1/2 digit LED voltmeter with a minimum of external components, (only 11 additional components). In this circuit, the 14511B provides the segment drive and the 75492 or 1413 provides sink for digit current. Display is blanked during the overrange condition.

2002 Microchip Technology Inc.

DS21394B-page 9

TC14433/A
FIGURE 4-1: 3-1/2 DIGIT VOLTMETER WITH LCD DISPLAY
0.1F V+ MCP1525 VIN VOUT VSS 1F 20k C01 C02 R1 470k 0.1F -V C R 14024B

R1/C 1C1 VX DS4 DS3 VAG DS2 DS1 TC14433 Q0 Q1 VREF Q2 Q3 VDD VSS VEE EOE DU RC RC +V -V 300k 14070B 1/4 +V

14013B 14070B 1/4 1/2 Digit D Q C R RQ 14013B D Q C R RQ Plus Sign +V BI D C B A Ph LD +V -V 14543B g f e d c b a +V -V

BI D C B A Ph LD 14543B g f e d c b a +V -V

BI D C B A Ph LD 14543B g f e d c b a

-V 1/4 14070B Minus Sign +V

DS21394B-page 10

2002 Microchip Technology Inc.

TC14433/A
FIGURE 4-2: 3-1/2 DIGIT LED VOLTMETER WITH LOW COMPONENT COUNT USING COMMON CATHODE DISPLAYS
470k 0.1F 0.1F

+5V MCP1525 VIN VOUT VSS 1F

VX

Input

20k

R1 R1/C C1 C01 C02 VX CLK1 VAG CLK0 DU OR Q0 EOE Q1 TC14433 Q2 VREF VSS VDD VEE DS4 DS3 DS2 DS1

300k

+5V

A B1 a B b C I4511B c d D e LT f LE VSS VDD g

Resitor Network or Individual Resistor* R

RDP

Alternate Overrange Circuit with Separated LED OR 1/6 75492 OR 1/7 1413 RR +5V

RM VEE** (Minus) +5V Minus Control 75492 OR 1413* Digit Drivers Common Cathode Led Display

Note 1: For VREF = 2000V; V: 1.999V full scale. 2: For VREF = 200mV; V: 199.9mV full scale (change 470k to R = 27k and decimal point position. 3: Peak digit current for an eight displayed is 7 times the segment current: *To increase segment current capability, add two 75491 ICs between 14511B and resistor network. The use of the 1413 as digit driver increases digit current capability over the 75492. **V can range between -2.8V and -11V.

FIGURE 4-3:

ALTERNATE OSCILLATOR CIRCUITS


(A) Crystal Oscillator Circuit (B) LC Oscillator Circuit

10

CLK1

10 C 11 C f= 1 2 2/LC

CLK1

C1

18M 11

TC14433
CLK0

TC14433
CLK0

C2

47k

10pF < C1 and C2 < 200pF

For L = 5mH and C = 0.01F, f 32kHz

2002 Microchip Technology Inc.

DS21394B-page 11

TC14433/A
FIGURE 4-4:
EOC

DIGIT SELECT TIMING DIAGRAM


1/2 Clock Cycle 16,400 Clock Cycles Between EOC Pulses

DS1 1/2 Digit (MSD) 2 Clock Cycles DS2

18 Clock Cycles

DS3 DS4 LCD

DS21394B-page 12

2002 Microchip Technology Inc.

TC14433/A
5.0
Note:

TYPICAL CHARACTERISTICS
The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range.

Typical Rollover Error vs. Power Supply Skew


ROLLOVER ERROR (IN LSD) AT FULL SCALE (PLUSE COUNT LESS MINUS COUNT) 4 3 2 1 0 -1 -2 -3 -4 -3 -2 -1 0 1 2 3 4 Note: Rollover Error is the Difference in Output Reading for the same Analog Input Switched from Positive to Negative. IQ - QUIESCENT CURRENT (mA)

Typical Quiescent Power Supply Current vs.Temp.


4

3 VEE = -8V VDD = +8V 2

1 VEE = -5V VDD = +5V 0 -40 -20 0 20 40 60 80 100

(VDD I-IVEE I) - SUPPLY VOLTAGE SKEW (V)

TA - TEMPERATURE (C)

Typical N-Channel Sink Current at VDD VSS = 5 Volts


5
ID - SINK CURRENT (mA) ID - SINK CURRENT (mA)

Typical P-Channel Sink Current at VDD VSS = 5 Volts


-3

4 3 2 1 0 0 1 2 3 4 5 VDS - DRAIN TO SOURCE VOLTAGE (VDC) -40C +25C +85C

-40C -2 +25C +85C -1

0 0 -1 -2 -3 -4 -5 VDS - DRAIN TO SOURCE VOLTAGE (VDC)

Typical Clock Frequency vs. Resistor (RC)


ICLK - CLOCK FREQUENCY (Hz) Note: 5% Typical Variation over Supply Voltage Range of 4.5V to 8V ICLK - CLOCK FREQUENCY (% CHANGE)

Typical % Change fo Clock Frequency vs. Temp.


4 3 2 1 0 -1 -2 -3 -4 -40 -20 0 20 40 60 80 TA - TEMPERATURE (C) CONVERSION RATE = MULTIPLEX RATE = CLOCK FREQUENCY 1.5% 16,400 CLOCK FREQUENCY 80 Normalized at 25C 8V Supply 5V Supply

1M

100k

10k

10k

100k

1M

RC - CLOCK FREQUENCY RESISTOR CLOCK FREQUENCY 1.5% 16,400 CLOCK FREQUENCY 80

CONVERSION RATE = MULTIPLEX RATE =

2002 Microchip Technology Inc.

DS21394B-page 13

TC14433/A
6.0
6.1

PACKAGING INFORMATION
Package Marking Information

Package marking data not available at this time.

6.2

Taping Form

Component Taping Orientation for 24-Pin SOIC (Wide) Devices

User Direction of Feed


PIN 1

P Standard Reel Component Orientation for TR Suffix Device

Carrier Tape, Number of Components Per Reel and Reel Size


Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size

24-Pin SOIC (W)

24 mm

12 mm

1000

13 in

Component Taping Orientation for 28-Pin PLCC Devices

User Direction of Feed


PIN 1

P Standard Reel Component Orientation for TR Suffix Device

Carrier Tape, Number of Components Per Reel and Reel Size


Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size

28-Pin PLCC

24 mm

16 mm

750

13 in

DS21394B-page 14

2002 Microchip Technology Inc.

TC14433/A
6.3 Package Dimensions

24-Pin PDIP (Wide)


PIN 1

.555 (14.10) .530 (13.46)

1.270 (32.26) 1.240 (31.50)

.610 (15.49) .590 (14.99)

.200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92)

.040 (1.02) .020 (0.51)

.015 (0.38) .008 (0.20) .700 (17.78) .610 (15.50)

3MIN.

.110 (2.79) .090 (2.29)

.070 (1.78) .045 (1.14)

.022 (0.56) .015 (0.38) Dimensions: inches (mm)

24-Pin CERDIP (Wide)


PIN 1

.540 (13.72) .510 (12.95)

.098 (2.49) MAX. 1.270 (32.26) 1.240 (31.50) .210 (5.33) .170 (4.32) .200 (5.08) .125 (3.18)

.030 (0.76) MIN. .620 (15.75) .590 (15.00) .060 (1.52) .020 (0.51) .015 (0.38) .008 (0.20) .700 (17.78) .620 (15.75) 3 MIN.

.150 (3.81) MIN.

.110 (2.79) .090 (2.29)

.065 (1.65) .045 (1.14)

.020 (0.51) .016 (0.41)

Dimensions: inches (mm)

2002 Microchip Technology Inc.

DS21394B-page 15

TC14433/A
Package Dimensions (Continued)

24-Pin SOIC (Wide)


PIN 1

.299 (7.59) .419 (10.65) .291 (7.40) .398 (10.10)

.615 (15.62) .597 (15.16) .104 (2.64) .097 (2.46) .012 (0.30) .004 (0.10)

8 MAX. .050 (1.27) .016 (0.40)

.013 (0.33) .009 (0.23)

.050 (1.27) TYP. .019 (0.48) .014 (0.36)

Dimensions: inches (mm)

28-Pin PLCC
PIN 1

.495 (12.58) .485 (12.32) .456 (11.58) .450 (11.43)

.050 (1.27) TYP.

.021 (0.53) .013 (0.33) .032 (0.81) .026 (0.66) .430 (10.92) .390 (9.91)

.456 (11.58) .450 (11.43) .495 (12.58) .485 (12.32) .180 (4.57) .165 (4.19)

.020 (0.51) MIN. .120 (3.05) .090 (2.29)

Dimensions: inches (mm)

DS21394B-page 16

2002 Microchip Technology Inc.

TC14433/A
SALES AND SUPPORT
Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com)

Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.

2002 Microchip Technology Inc.

DS21394B-page 17

TC14433/A
NOTES:

DS21394B-page 18

2002 Microchip Technology Inc.

TC14433/A

Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchips products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights.

Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, MXLAB, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
Printed on recycled paper.

Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Companys quality system processes and procedures are QS-9000 compliant for its PICmicro 8-bit MCUs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchips quality system for the design and manufacture of development systems is ISO 9001 certified.

2002 Microchip Technology Inc.

DS21394B-page 19

WORLDWIDE SALES AND SERVICE


AMERICAS
Corporate Office
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com

ASIA/PACIFIC
Australia
Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755

Japan
Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122

Rocky Mountain
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456

China - Beijing
Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104

Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934

Atlanta
500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307

Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850

Boston
2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821

China - Chengdu
Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599

Taiwan
Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139

Chicago
333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075

Dallas
4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924

China - Fuzhou
Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521

EUROPE
Denmark
Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910

Detroit
Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260

China - Shanghai
Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060

Kokomo
2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387

France
Microchip Technology SARL Parc dActivite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79

Los Angeles
18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338

China - Shenzhen
Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086

New York
150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335

Germany
Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44

San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955

China - Hong Kong SAR


Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431

Italy
Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883

Toronto
6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509

India
Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, OShaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062

United Kingdom
Microchip Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820
05/01/02

*DS21394B*
DS21394B-page 20

2002 Microchip Technology Inc.

You might also like