Professional Documents
Culture Documents
ON
PLATFORM USED
BLOCK DIAGRAM
MICROCONTROLLER UNIT
REFERENCE
INTRODUCTION
The natures most spectacular creation is human brain. The main feature of the human brain is its ability to sense the obstacles and respond according to them. The men always want to transplant his ability to the artificial things so that they can not only sense the problem but also respond according to that. In this competitive corporate world every organization wants to improve the efficiency as well as its productivity. To improve the efficiency of organization, automation is a preferred solution. This system is based on mobile technology in which you can perform the long distance communication. Using mobile communication we can also switch the heavy machines in industries and can secure the machines from accessing by other person . For this purpose password is given to each machine that can be type through your mobile from anywhere and can switch the machine that you want to on or off. Suppose if all the machines are controlled by a manager or any other person in a industry and if he is not present when it is urgent to turn on a machine but that machine can only turn on when the authorized person enter the password through his mobile. Then a call can made to that person to request him for turning on the machine ,then he could turn them on through any where by just dialing the password to turning on the .
Here the use of DTMF signal is done .DTMF signaling is used for telephone signaling over the line in the voice frequency band to the call switching center. The
version of DTMF used for telephone dialing is known as touch tone. DTMF assigns a specific frequency (consisting of two separate tones) to each key s that it can easily be identified by the electronic circuit. The signal generated by the DTMF encoder is the direct al-gebric submission, in real time of the amplitudes of two sine(cosine) waves of different frequencies, i.e. ,pressing 5 will send a tone made by adding 1336hz and 770hz to the other end of the mobile. The tones and assignments in a dtmf system shown below
PLATFORM USED
SOFTWARE REQUIREMENTS 1. Batronix Prog Studio for programming of Microcontroller 2. Orcad for Circuit Designing 3. Pads for PCB designing
HARDWARE REQUIREMENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Microcontroller 89c51/89s52 Crystal Oscillator Resistor Diode Capacitor Transistor Connectors Relay Cell phone Function numeric display Voltage regulator
The aim of the project is to investigate a cost effective solution that will provide switching of machine in industry remotely. The motivation is to facilitate the users to automate their industry having ubiquitous access. The system provides availability due to development of a low cost system. The system is using mobile for making the work of switching machines very easier .Through cell phone and the microcontroller we are aiming for successful completion of this project.
BLOCK DIAGRAM
BLOCK DIAGRAM
SUPPLY SECTION
Electrica l machine
MOBILE UNIT
IN this project a call is made to the mobile which is communicating with the microcontroller serially ,phone which is connected to the microcontroller will receive the call after some time automatically then the user dial a specific password to switching the machine .when the user dial that password receiver of the mobile unit connected to circuit communicate it with the microcontroller .Since today we use the DTMF technology for communication each number on keypad has its own frequency in our circuit we will use a DTMF receiver for converting the received frequencies by the mobile unit into digital signal and apply it to the pins of the microcontroller, microcontroller will read that execute the instructions stored in it ,and switch the machine connected at its output pin .
MICROCONTROLLER UNIT
MICROCONTROLLER:
MICROCONTROLLER AT89s51
Features Compatible with MCS-51 Products 8K Bytes of In-System Re programmable Flash Memory Endurance: 1,000 Write/Erase Cycles Fully Static Operation: 0 Hz to 24 MHz Three-level Program Memory Lock 256 x 8-bit Internal RAM 32 Programmable I/O Lines Three 16-bit Timer/Counters Eight Interrupt Sources Programmable Serial Channel Low-power Idle and Power-down Modes
DESCRIPTION The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer 8Kbytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel s high-density nonvolatile memory technology and is compatible with the industry standard 80C51 and 80C52 instruction set and pin out. The on-chip Flash allows the program memory to be reprogrammed insystem or by a Conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputer that provides a highly flexible and cost-effective solution to many embedded control application.
The AT89C52 provides the following standard features: 8K bytes of Flash, 256 bytes of RAM, 32 I/O lines, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full-duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89C52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode tops the CPU while allowing the RAM; timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but Freezes the oscillator, disabling all other chip functions until the next hardware reset
BIBLIOGRAPHY ELECTRONIC DEVICES AND CIRCUIT THEORY BY ROBERT L. BOYLSTEAD AND LOUIS NASHELSKY OP-AMPS AND LINEAR INTEGRATED CIRCUITS BY RAMAKANT A. GAYAKWAD DIGITAL DESIGN BY M.MORRIS MANO A COURSE IN ELECTRICAL END ELECTRONIC MEASUREMENTS AND INSTRUMENTATION BY A.K.SAWHNEY SOME OF THE FOLLOWING WEB SITES WERE ACCESSED
www.parallaxinc.com