You are on page 1of 4

PMDG 737NGX Checklist Preflight procedure Ground cart - Connect Battery switch - Guard Closed Standby Power - Guard

Closed Ground Power - ON IRS IRS - Off then NAV CDU/FMC POS INIT Page - SER IRS POS LINE DOORS Open doors - As needed Air Stairs - As needed EMERGENCY EXIT LIGHTS Emergency Exit Lights Switch - Guard closed PASSENGER SIGNS No Smoking/Chime - AUTO or ON Fasten Belts - AUTO or ON HEAT AND ANTI-ICE Window Heat - ON Probe Heat - OFF Wing Anti-ice - OFF Engine Anti-ice - OFF AIR CONDITIONING PANEL Check Trim air - ON Recirc. Fan Switches - AUTO Air Cond. Pack Switches - AUTO or HIGH Isolation Valve Switch - OPEN Engine Bleed Air switches - ON CABIN PRESSURIZATION PANEL Flight Altitude Indicator Set - CRUISE ALTITUDE Landing Altitude - DESINATION FIELD ELEVATION LIGHTING PANEL LOGO - As needed (ON) Position Lights - As needed (ON) Anti Collision - OFF Wing Illumination - AS NEEDED RADIO Contact ATIS - QNH, RWY, TEMP VHF COM. Radios - SET VHF NAV. Radios - SET Contact ATC for clearance - ALTITUTE, SQUAWK Transponder - SET Squawk code CDU/FMC Set up FMC. Walkthrough available PMDG NGX FCOM1 page 79-81. Set fuel/pax first EFIS Control Panel Minimum Reference Selector - RADIO or BARO

Minimum Selector- Set Decision Height MCP (MODE CONTROL PANEL) Course - SET Auto Throttle - ARM Flight Director Switches - ON IAS - SET V2 Initial Heading - SET Initial Altitude - SET Bank Angle Selector - As Needed LNAV - As Needed VNAV - ARM APU APU - START FUEL PANEL ALL Fuel Pumps - ON DOORS Exterior Doors - CLOSE APU APU Generator Switches - ON APU Bleed Air Switch - ON GROUND POWER Ground Power - OFF and REMOVE OVERHEAD PANEL Electric Hydraulic Pump Switches - ON Anti Collision Light Switch - ON YAW Damper Switch - ON FLIGHT DECK AND CONTROL STAND Speed brake lever - DOWN DETENT TRIM - SET Parking Brake - ON Auto Brake Select Switch - RTO Engine Display Control Panel - ON PUSH BACK AND START ENGINES CDU Push back, Set up as needed - START (follow crew) Engine Ignition Selector - BOTH Air Conditioning PACK Switches - OFF Engine #2 Start Switch - GRD When N2 RPM is at 25% - ENGINE START LEVER IDLE Wait for Engine 2 Starter - CUT OUT Engine #1 Start Switch - GRD When N2 RPM is at 25% - ENGINE START LEVER IDLE Wait for Engine 1 Starter - CUT OUT BEFORE TAXI PROCEDURE Generator 1&2 Switches - ON Probe Heat - ON Wing Anti-Ice - AS NEEDED Engine Anti-Ice - AS NEEDED Pack Switch - AUTO Isolation Valve - AUTO APU Bleed Air Switch - OFF APU Switch - OFF

Engine Start Switches - CONT Set Flaps - 5 (As needed) Lower Engine Display - OFF Lights - As needed TAXI Follow TAXI Clearance CLEARED FOR TAKEOFF Strobe Lights - ON Fixed landing Lights - ON Transponder Mode - TA/RA Line up Runway Advance Thrust Levers to 40% N1 - Stabilize TO/GA - ON At VR - ROTATE AFTER TAKEOFF Positive Rate of Climb - Gear Up At 400ft Radio Select Roll Mode - SELECT(if V/LNAV Armed = CMD A ON) At Acceleration height - Flaps Up After Flaps and Slats Retract - VNAV/LNAV (if not armed) CMD A - ON Auto Brakes - OFF Engine Start Switches - OFF Landing Gear - OFF CLIMB AND CRUISE Altitude - SET assigned Altitude change - PRESS alt change At Transition ALT - BARO STD At 10,000FT - LANDING LIGHTS OFF 5 Miles before Decent - SET ALT DESCENT CDU/FMC - VREF FLAPS 30% (As needed) NAV Radios ILS Frequencies - SET MCP Course of RWY - SET Auto Brakes - AS NEEDED (2) Minimums - SET RADIO 100ft At 10,000ft - LDG LIGHTS ON Map Range - 10nm (As needed) At Flaps Up Speed - FLAPS 1 Speed Brakes - WHEN Required APPROACH Before Intercept - VOR/LOC ARM Turning onto Localizer - FLAPS 5 Localizer Captured - APP ON CMD B - ON (autoland) IAS - SET VREF +5 Engine Start Selectors - CONT At Flaps 5 Speed - FLAPS 15 Landing Gear - DOWN At Flaps 15 - FLAPS 30 Speed Brakes - ARM LANDING At Touch Down - THRUST REV. ON 80 Knots - THRUST REV. OFF

Auto Brakes - - DISENGAGE Auto Pilot if ON - OFF AFTER LANDING Speed brakes - DOWN APU - START PROBE HEAT - OFF Landing Lights - OFF Position Lights - ON STEADY Engine Start Selectors - OFF Auto Brakes - OFF FLAPS - UP Transponder - ALT OR STBY SHUTDOWN PROCEDURE Parking Brake - ON APU Generator - ON (BOTH) Engine Start Levers - CUT OFF Doors - AS NEEDED Air Stairs - AS NEEDED Fasten belts - OFF Anti-Collision Lights - OFF Fuel Pumps - OFF HYD Pumps - OFF Isolation Valve - OPEN APU BLEED - ON Flight Directors - OFF Transponder - STANDBY Ground Connections - CHOCKS Parking Brake - OFF *Ground Connections - Ground Power *opt* *Ground Power - ON *opt* APU Bleed - OFF APU - OFF SECURE COCKPIT IRS - OFF EMER Exit Lights - OFF Window Heat - OFF PACKs - OFF Verify APU - TURNED OFF Battery (If No Ground power) - OFF

Canto dos Aviadores Virtuais http://cantodosaviadoresvirtuais.blogspot.com.br

You might also like