Professional Documents
Culture Documents
Data Sheet
aIVR1004 10 sec aIVR2104 21 sec aIVR4208 42 sec
APLUS
Address: 3 F-10, No. 32, Sec. 1, Chenggung Rd., Taipei, Taiwan 115, R.O.C. (115) 32 3 10. TEL: 886-2-2782-9266 FAX: 886-2-2782-9255 WEBSITE : http: //www.aplusinc.com.tw
sales@aplusinc.com.tw
Technology E-mail:
service@aplusinc.com.tw
DESCRIPTION
Aplus aIVR is a 8-bit CPU based Voice chip series. It is fabricated with Standard CMOS process with embedded voice storage memory. It can store from 10 to 42sec voice message with 4-bit ADPCM compression at 6KHz sampling rate. 8-bit PCM is also available as user selectable option to improve sound quality. Depending on IC body, there are up to twelve programmable I/O pins. Key trigger and Parallel CPU trigger mode can be configured according to different application requirement. User selectable triggering and output signal options provide maximum flexibility to various applications. Built-in resistor controlled oscillator, 8-bit current mode D/A output and PWM direct speaker driving output minimize the number of external components.
Programmable IO 4 4 8
PIN DESCRIPTIONS
Pin Names VOUT1 VOUT2_COUT VSS OSC VDDA VDD PBn PCn RSTB Description PWM output to drive speaker directly PWM output or COUT DAC output select by programmable option Power Ground Oscillator input Positive Power Supply Positive Power Supply Programmable I/O pins (n: 0 to 3 for all aIVR chips) Programmable I/O pins (n: 0 to 3 for aIVR4208 only) Reset pin, Low active
Note: PBn and PCn are software programmable I/O pins that can be set to different configurations such as pure input, input with pull-up, input with pull-down and output. The programmable I/O pins set up will take effect immediately after chip RESET is applied.
OSC
8-bit MCU
PB0 ~ 3 PC0 ~ 3
I/O
VOUT1
VOUT2_ COUT
Parameter
Operating Voltage Standby current Operating current "H" Input Voltage "L" Input Voltage VOUT low O/P Current VOUT high O/P Current COUT O/P Current O/P High Current O/P Low Current VOUT pull-down resistance Programmable IO pin pull-down resistance Programmable IO pin pull-up resistance
Min.
2.2 2.5 -0.3 3.3K
Typ.
3.0 1 3.0 0 130 -130 -2 -8 8 100K
Max.
3.6 5 15 3.5 0.5
Unit
V A mA V V mA mA mA mA mA
Conditions
I/O properly terminated I/O properly terminated VDD=3.0V VDD=3.0V Vout=1.0V Vout=2.0V Data = 80h VOH=2.5V VOL=0.3V VOUT pin set to internal pull-down PBx, PCx, PDx set to internal pull-down PBx, PCx, PDx set to internal pull-up VDD = 3V +/- 0.4V Also apply to lot to lot variation
1M 4.7K
Fs/Fs
Frequency stability
-3
+3
Fc/Fc
-5
+5
C1
R1 ROSC=610K
VDD,VDDA OSC PB0 PB1 PB2 VOUT1 VOUT2_ COUT PB3 RSTB
8 / 16 Speake
3.3V
Rrst = 4.7K
Crst = 0.1uF
VSS
Note : PB0 to PB2 are set to input; PB3 is set to output C1 = 0.1uF to 2.2uF depend on the kind of power supply and before the main switch. R1 = 1M Ohm is optional for fast discharge of Crst when power off.
HT7335
C1 ROSC = 610K
8 1/4W Speaker
4.5V
4.7K
RSTB VSS
0.1uF
Note : PB0 to PB2 are set to input C1 = 0.1uF to 2.2uF depend on the kind of power supply.
Output driving of HT LDO: HT7136 (30mA, 3.6V) HT7133 (30mA, 3.3V) HT7536 (100mA, 3.6V) HT7335 (250mA, 3.5V)
VIN=+5V
VOUT=+3.5V
HT7335
C1 ROSC =610K 4.7K 8 1/4W Speaker
Note: 1. C1 is capacitor from 0.1uF to 2.2uF depends on the kind of Vdd source and sound loudness. E.g. If COUT is used, C1 can be 0.1uF. However, if PWM direct drive speaker is used, C1 should be at least 2.2uF 2. Rb is base resistor from 120 Ohm to 390 Ohm depends on Vdd value and transistor gain. 3. Tr is an NPN transistor with beta larger than 150, e.g. 8050D. 4. Rosc = 610K Ohm with Vdd=3.0V and support sampling rate up to 14KHz 5. For sampling rate higher than 14KHz, smaller value of Rosc should be used.
MCU
VOUT2_ COUT
Rb
Tr
0.1uF
VSS
Note : PB0 to PB2 set to internal pull-up Addr[0] to [2] are open drain output drive