Professional Documents
Culture Documents
Qhyst1 : Qhyst1 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH RSCP (def:4) (A_WCEL) Qhyst2 : Qhyst2 is used for FDD cells when cell selection and re-selection quality measure is set to CPICH Ec/No (def:4) (A_WCEL) QqualMin : The minimum required quality level in the cell (Ec/No) (def:-20) (A_WCEL) QrxlevMin : The minimum required RX level in the cell (def: WCDMA -115, GSM -105) (A_WCEL) SHCS_RAT : The RAT specific threshold for inter-RAT measurement rules (def:1) (A_WCEL) Sintersearch : The threshold for inter-frequency measurements, and for the HCS measurement rules (def:2) (A_WCEL) Sintrasearch : The threshold for intra-frequency measurements, and for the HCS measurement rules (def:4) (A_WCEL) Slimit_SearchRAT : Threshold for skipping inter-RAT measurement rules in HCS (def:2) (A_WCEL) Ssearch_RAT : The RAT-specific threshold for inter-RAT measurement rules (def:0) (A_WCEL) SsearchHCS : Threshold for intra- and interfrequency measurement rules in HCS (def:1) (A_WCEL) TCrmax : The duration for evaluating the allowed amount of cell reselections (def:60sec) (A_WCEL) TCrmaxHyst : Cell reselection hysteresis for reverting from UE high-mobility measurements (def:0sec) (A_WCEL) Treselection : The UE triggers the reselection of a new cell if the cell reselection criteria are fulfilled during the time interval Treselection (def:0) (A_WCEL) UseOfHCS : Indicates whether the serving cell belongs to a Hierarchical Cell Structure (HCS), or not (def:0) (A_WCEL)
With this parameter you define the threshold for GPRS capable dual mode mobiles to search for and to measure UTRAN neighbour cells introduced in 3G Cell Reselection list when a running average of the received downlink signal level (RLA_C) of the serving cell is below (0-7) or above (8-15) the threshold. This parameter is broadcast on BCCH. In case this parameter is broadcast on BCCH it shall be used only if GPRS cell re-selection parameters for one or more cells are sent to the MS in a Packet Cell Change Order or Packet Measurement Order message If the parameter value is 7, GPRS-capable multi-RAT MSs measure always neighbour UTRAN cell(s). If the parameter value is 15, GPRS-capable multi-RAT MSs do not measure any of neighbour UTRAN cells. GPRS-capable mobiles use this parameter only if NCCR is active in the serving cell fddQOffset (A_BTS) With this parameter you define a UTRAN cell reselection offset for non-GPRS capable dual mode mobiles which are in the idle state. The mobiles add the offset to the running average (RLA_C) of the received signal level of the serving GSM cell and non-serving GSM cells. After that the mobiles compare the measured RSCP values of UTRAN cells with signal levels of the GSM cells. -32 db = minus infinity dB range: -28..28 dB, step 4 dB FDD_GPRS_Offset FDDQmin (A_BTS) This parameter defines a minimum Ec/Io threshold which must be exceeded before a non-GPRS capable dual mode mobile is allowed to make a reselection from the serving GSM cell to an adjacent WCDMA RAN cell that is using frequency division duplex (FDD) type access technology/mode FDD_REP_QUANT defines the reporting quantity for UTRAN cell 3G_Search_PRIO Is used to inidicate to the MS if 3G cells can be looked for when BSIC decoding is required. (0=no, 1=yes, default: 1)
ADMISSION CONTROL Admission control decides whether or not an incoming call can be accepted. A new radio connection is admitted by the CRNC which accounts for the available resources at the corresponding Node B. The allocation of resources includes the allocation of the corresponding downlink spreading and channelization code pair. The objective of admission control is to maintain call quality in each cell by limiting admission of radio bearers. If radio bearers were granted without limit, the
interference level in the cell would increase, leading to degradation of the call quality. In addition to the admission control function in the RNC, the Node B performs admission control to protect the Node B against too high transmission power requirements. The Node B estimates the transmission power requirement of a new radio link and verifies whether the total transmission power is below the maximum allowable transmission power
Admission control memutuskan boleh atau tidak panggilan masuk dapat diterima.Koneksi radio baru diakui oleh CRNC yang menyumbang sumber daya yang tersedia padaNode B. sesuai Alokasi sumber daya termasuk alokasi downlink yang sesuai menyebardan pasangan channelization kode. Tujuan dari admission control adalah menjaga kualitas panggilan dalam sel masing-masing dengan membatasi pengakuan pembawa radio. Jikapembawa radio diberikan tanpa batas, tingkat gangguan pada sel akan meningkat,menyebabkan degradasi kualitas panggilan. Selain fungsi kontrol masuk di RNC, Node Bmelakukan admission control untuk melindungi terhadap Node B juga kebutuhan dayatransmisi yang tinggi. Node B memperkirakan kebutuhan transmisi daya dari radio linkbaru dan memverifikasi apakah daya transmisi total di bawah daya transmisi maksimum yang diijinkan
Lapisan RRC di UE meninggalkan modus idle dan memulai sebuah pembentukan koneksi RRC dengan mengirimkan pesan RRC Permintaan Koneksi menggunakan modus RLC transparan pada saluran CCCH logis. Ini logical channel akan dipetakan ke Rach transportasi saluran dengan MAC. Peta saluran Fisik Rach ini ke PRACH dan mengirimkan pesan ini ke jaringan. Ingat bahwa UE tidak dapat mengirim seperti pesan permintaan secara spontan melalui PRACH, karena PRACH ini akan digunakan oleh semua UES dalam sel. Jadi UE akan mendengarkan AICH saluran untuk mengetahui slot waktu yang ditetapkan untuk ini UE untuk menggunakan PRACH. (Untuk mengetahui lebih lanjut tentang ini klik di sini). BTS adalah benar-benar transparan untuk pesan ini, karena tidak memiliki lapisan RRC. Pada sisi jaringan, berdasarkan penerimaan Permintaan Koneksi RRC, lapisan RRC melakukan admission control, memberikan sebuah s-RNTI untuk sambungan RRC dan memilih parameter sumber daya radio (seperti jenis saluran transportasi, format transportasi set dll). Jika dch adalah untuk dibentuk, CPHY-RL-Setup dan primitif permintaan CPHY-TrCH-Config (ditransmisikan sebagai salah satu RADIO LINK SETUP PDU) yang dikirim ke semua Node B yang akan terlibat dalam pembentukan saluran. Operasi lapisan fisik dimulai dan primitif konfirmasi kembali dari masing-masing Node B. mengkonfigurasi parameter RRC pada lapisan 2 untuk membangun saluran logis DCCH lokal. Parameter yang dipilih termasuk RNTI,
ditransmisikan ke UE dalam pesan Connection Setup RRC menggunakan modus diakui pada saluran logis CCCH. Setelah penerimaan pesan Pengaturan Koneksi RRC, lapisan RRC di UE mengkonfigurasi L1 dan L2 menggunakan parameter untuk lokal membangun saluran logis DCCH. Dalam kasus dch, lapisan 1 menunjukkan ke RRC ketika telah mencapai sinkronisasi. Link sinyal RLC adalah lokal didirikan di kedua sisi. Pembentukan dapat dipetakan di kedua Rach / FACH atau dch oleh MAC. Ketika UE telah membentuk link sinyal RLC, itu mengirimkan pesan RRC Koneksi Pengaturan Lengkap untuk jaringan menggunakan modus mengakui pada DCCH tersebut.