You are on page 1of 3

Project No: Client: Project : Package Desc:

1110
SBM / ESSO EXPLORATION ANGOLA (BLOCK 15) LTD

KIZOMBA C- FPSO SAXI BATUQUE TEG REGENERATION SYSTEM - A-T7210

SLING SELECTION Using a load factor of 3.0 for skid member, lifting eye, spreader bar Maximum Axial force in the sling (with load factor 3.0) = Static Sling Load = 45.87 Tonne 15.29 Tonne

Now, with 2 1/2" nominal diameter rope @ 17.3kg/m mass (Refer TABLE 3.7 of API Spec. 9A) Net area is calculated considering density of steel Mass = Density of steel = Net area, A = Mass / Density = With 60 ksi steel, Fy=

17.3 kg/m 7850 kg/m3 22.04 cm2 413.69 N/mm2

Capacity of the sling = 0.6 x Fy x A x 102 / 104 = 54.70 Tonne More than sling load hence safe Again, nominal breaking load of the sling = 238 Tonne As per cl. 2.4.2f of API RP 2A Safe load is one fifth of nominal breaking load = 47.6 Tonne More than sling load hence safe
Tp

R = W/2 Dh t d1 h

Stiffener Plate

Detail of Lifting Lug at Skidbase

Project No: Client: Project : Package Desc:

1110
SBM / ESSO EXPLORATION ANGOLA (BLOCK 15) LTD

KIZOMBA C- FPSO SAXI BATUQUE TEG REGENERATION SYSTEM - A-T7210

Design of Liftng Lug at Skid base Considering Crosby bolt type shackle G-2130 of size 21/2 inches. Assumed data: Main plate thickness, Tp = Cheek plate thickness, t = Width of pad eye, W = Radius of edge of lifting eye, R = Cheek plate diameter, d1 = Diameter of pin, B = Diameter of shackle hole, E = Yield stress, fy = Radius of hole, Rh = Radius of cheek plate, r = Distance of cheek plate from edge, e = Dist. of base from centre of cheek plt, h = Force in the bottom sling P1(with load factor 3.0) = Angle of inclination of rope, q cosq = Sinq = Force in vertical direction, FZ =P1Sinq = Force in lateral direction, FX =P1 Cosq = Force in longitudinal direction Fy = 5% of P1 A. Clearance of shackle Clear distance from pin to end, E+ B/2= Rope diameter, d = Actual distance reqd. = Edge radius + Rope dia = R+d = 301.625 mm 64 mm 264 mm which is less than actual available 55 mm 104.775 mm which is more than reqd.
2 1874 mm

25 15 400 200 220 69.85 266.7 248.2 37 110 40 200

mm mm mm mm mm mm mm N/mm2 mm mm mm mm

45.87 Tonne 68.45 0.3673 0.9301 42.6636 Tonne 16.8486 Tonne 2.2935 Tonne

Overall thickness of lifting eye at edge of hole =Tp + 2t= Clear dimension of pin inside the shackle, i.e jaw width, A = A. Required bearing area of the pin Area required for bearing, Ab=Fz/0.9fy= Then total plate thickness required, Tr=Ab/B Overall thickness, T=

26.82 mm 55 mm which is more than reqd.

Project No: Client: Project : Package Desc:

1110
SBM / ESSO EXPLORATION ANGOLA (BLOCK 15) LTD

KIZOMBA C- FPSO SAXI BATUQUE TEG REGENERATION SYSTEM - A-T7210

Required area of shear for vertical load Area required for Shear, As = Fz/0.4fy = Area available for Shear, Asa = 4(r-Rh)t = 2(R-Rh)Tp=
2 4215.65 mm 2 12530 mm

Combined Axial & Bending Stress Length of main plate, L1 = Thickness of main plate, t1 = Area, A2 = L1t1 = 400 mm 25 mm 2 10000 mm

Moment of inertia of the section I2y=t1L13/12 Z2y=I2y/0.5L1 I2x=L1t13/12 Z2x = I2x/0.5t1 Dist of base from center of cheek plate,h = Axial stress,sa = Fz /A2 = Inplane Bending stress,sby=Fx x h /Z2y = Out of plane Bending stress, sbx=Fy x h / Z2x = So, combined stress s = Fz/A2 + Fx x h / Z2y + Fyx h/Z2x = <fy/1.45= NotSafe F: Shear Stress for lateral & longitudinal force tx=Fx/A2 = ty=Fy/A2 = 16.5285 <fy/2.16 = 2.2499 <fy/2.16 =

4 133333333.3 mm 3 666666.6667 mm 4 520833.3333 mm 3

41666.66667 mm

150 mm 2 41.85 N/mm 2 49.59 N/mm


2 108.00 N/mm

2 199.43 N/mm

171.17 N/mm

114.91 N/mm 2 114.91 N/mm Hence Safe

You might also like