You are on page 1of 5

Two Way Slab: (Analysis by Coefficient Method) Ms = Mb = Cs and Cb w = Ls = CS wLs2 Cb wLb2 (moment along short direction) (moment along

long direction)

back to page 1

= tabulated moment coefficients from table uniform load KN/m length of clear span in short direction

Lb = length of clear span in long direction Moments at the column strip is only 1/3 of the midspan moments Insert Variables: A 6 B 7.5 Insert Variables: fc' 20.7 Mpa fy 415 Mpa

meters meters

Thk.min assumed Thk. = dead load = Wu =

150 150 mm 100 mm 2.354 Kpa 14.4476 Kpa d= live load = 75 mm 6.56 Kpa

Considering 1 meter strip Wu = m= 0.8

14.4476 KPa

COEFFICIENT FOR NEGATIVE MOMENTS IN SLABS RATIO Values CASE1 0 RATIO Values CASE 1 0 0.75 Ca neg

CASE 2 0.069 O.75 Cb neg

CASE3 0

CASE 4 CASE5 CASE6 CASE7 CASE8 CASE 9 0.076 0.085 0.088 0 0.061 0.078

CASE2 0.022

CASE 3 CASE4 CASE 5 CASE 6 0.056 0.024 0

CASE 7 CASE 8 CASE 9 0.044 0.036 0.014

CHOOSE CASE # Ca neg Cb neg #VALUE! #VALUE!

COEFFICIENT FOR DEAD LOAD POSITIVE MOMENTS IN SLABS RATIO 0.75 Ca dl

Values CASE 1 CASE2 0.061 RATIO 0.75 Cb dl

0.028

CASE 3 CASE4 CASE 5 CASE 6 CASE 7 CASE 8 CASE 9 0.04 0.043 0.033 0.048 0.051 0.036 0.031

Values CASE 1 CASE2 0.019

0.009

CASE 3 CASE4 CASE 5 CASE 6 CASE 7 CASE 8 CASE 9 0.018 0.013 0.007 0.012 0.02 0.013 0.007

CHOOSE CASE # Ca dl Cb dl #VALUE! #VALUE!

COEFFICIENT FOR LIVE LOAD POSITIVE MOMENTS IN SLABS RATIO 0.75 Ca ll

Values CASE 1 CASE2 0.061 RATIO 0.75 Cb ll

0.045

CASE 3 CASE4 CASE 5 CASE 6 CASE 7 CASE 8 CASE 9 0.051 0.052 0.047 0.055 0.056 0.049 0.046

Values CASE 1 CASE2 0.019

0.014

CASE 3 CASE4 CASE 5 CASE 6 CASE 7 CASE 8 CASE 9 0.019 0.016 0.013 0.016 0.02 0.016 0.013

CHOOSE CASE # Ca Ll Cb Ll #VALUE! #VALUE!

Negative Moments at continuous edge:

case_4

Ms = #VALUE! KN.m Mb = #VALUE! KN.m Positive Moments: Along Short Direction: Ms dl= #VALUE! KN.m Ms Ll = #VALUE! KN.m Ms total = #VALUE! KN.m Along Short Direction: Mb dl= ###### KN.m Mb Ll = ###### KN.m Mb total = ###### KN.m

Negative Moment at discontinuous edges equals 1/3 of positive moment: Ms = #VALUE! KN.m Mb = #VALUE! KN.m

along short direction: 1. Midspan: Mu = fc' bd w(1 - 0.59w) #VALUE! = 104793750 w -61828313 w

W = #VALUE! p = #VALUE! As = #VALUE! mm use 12 mm bars: say 0 mm

S = #VALUE!

2. continuous edge: Mu = fc' bd w(1 - 0.59w) #VALUE! = 104793750 w -61828313 w

W = #VALUE! p = #VALUE! As = #VALUE! mm Use 12mm bars: S = #VALUE! say 0 mm

3. discontinuous edge: = use 3 times the spacing of midspan (moment is only 1/3 of midspan) S = #VALUE! mm>> 500mm(ACI Code) bent up two of every three bars from the bottom steel

along long direction: 1. Midspan: Mu = fc' bd w(1 - 0.59w) #VALUE! = 104793750 w -61828313 w

W = #VALUE! p = #VALUE! As = #VALUE! mm use 10 mm bars: say 0 mm

S = #VALUE!

2. continuous edge: Mu = fc' bd w(1 - 0.59w) #VALUE! = 104793750 w -61828313 w

W = #VALUE! p = #VALUE! As = #VALUE! mm Use 12mm bars: S = #VALUE! say 0 mm

3. discontinuous edge: = use 3 times the spacing of midspan (moment is only 1/3 of midspan) S = #VALUE! mm>> 500mm(ACI Code) bent up two of every three bars from bottom bars

You might also like