Professional Documents
Culture Documents
V1
USES
C H A RAC T E R I S T I C S
I Good ow characteristics, for a smooth nish I Good adhesion to clean, degreased substrates
P R O P E RT I E S
Composition Finish Theoretical Spreading Rate Practical Spreading Rate Zinc phosphate primer, based on an alkyd resin. Matt. At a dry lm thickness of 50 micrometres: 13.5m2/litre. In assessing a practical spreading rate, other factors such as shape of the construction, roughness of the substrate, method and conditions of application, should be considered. A guideline for spraying is: Large Areas: Approx 70% of theoretical coverage. Small Areas: Approx 50% of theoretical coverage. Drying Time Touch dry within 5 hours and recoatable after 12 hours at 20 C and 65% relative humidity. Minimum recommended application temperature 5 C. At lower temperatures and/or conditions of high relative humidity, drying periods will be extended. Washability Volume Solids Flammability Storage Resistant to washing and scrubbing. Clean with a mild detergent solution or white spirit to remove dirt and stains. Approximately 67%. 32 C. Keep in a cool, dry place.
0 0 0
A P P L I CAT I O N
Method Initial Procedure Thinning Brush: For best results use a long haired soft bristle brush. Apply one coat at 75m wet lm thickness. Stir well immediately prior to use. Brush: Ready for use. Do not thin.
Also suitable for application by air-assisted airless spray. The following information is given as a guide. Method Thinning Fluid Pressure Air Assistance Fluid Tip Angle Wet Film Thickness Dry Film Thickness Cleaning of Equipment Conditions of Application Air-assisted airless spray. Up to 5% (by volume) with Sikkens M600 Thinners. 2000-2350 psi (140-160 bar). Up to 45 psi (approx 3 bar). 0.015 (0.380mm). Dependent on size of substrate. 83 micrometres per coat. 50 micrometres per coat. Clean brushes and equipment in clean Sikkens M600 Thinners immediately after use. Do not apply if there is a risk of rain, or when air/substrate temperatures are below 5C during application or drying periods. The substrate temperature must be at least 3C above the dew point. Protect from frost and rain until dry. Sikkens Redox AK Primer must not be overcoated with Sikkens Onol Express Primer/Undercoat.
Re d ox A K P r i m e r
C O LO U R RA N G E
White.
PAC KAG I N G
1 litre.
SA F E T Y, H E A LT H & ENVIRONMENT
It is the policy of Akzo Nobel Woodcare to provide the highest standard of safety, health and environmental advice and information. To this end, safety data covering every Akzo Nobel Woodcare product is supplied to our customers and is freely available to users on request, either through our merchants or direct from us. The safety phrases on the container and material safety data sheet should be read before using this product.
G E N E RA L I N F O R M AT I O N
Apply all products in accordance with BS 6150 : 1991, BS 8000 - 12 : 1989 and BS 5493 : 1977. Every care is taken to ensure that the information provided in this technical data sheet is accurate. Akzo Nobel Woodcare is unable to guarantee results as it has no control over the conditions under which its products are applied. For further help and information contact the Customer Services Department on 01480 496868. Before using this product ensure that you have the latest information available. The information above is correct at the date of issue, July 1999.
Akzo Nobel Woodcare, Meadow Lane, St Ives, Cambs, PE17 4UY. Tel: 01480 496868 Fax: 01480 496801 Email: woodcare@stives.deconorth.com 4ABXJ04200/7/99