Professional Documents
Culture Documents
Refer to the exhibit. Based on the output shown, to which IP network should the
workstations in the Support department belong?
192.168.1.0
172.16.1.0
172.16.3.0
172.16.5.0
2
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. Given the output generated by the debug ppp negotiation
command, which statement is true?
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
4
What is important to consider while configuring the subinterfaces of a router when
implementing inter-VLAN routing?
The IP address of each subinterface must be the default gateway address for each
VLAN subnet.
Refer to the exhibit. A lab technician connects two routers together via a serial cable
using the default interface configuration values. The interfaces are up; however, the
technician is unable to ping between the two devices. What is the most likely
problem?
The lab technician used the wrong cable to connect the serial ports.
Refer to the exhibit. Based on the output shown, why is VTP information unable to
propagate the network?
One of the two client mode switches must be reconfigured to Transparent mode.
7
The enterprise mail server software recently went through a minor update. A network
administrator notices an excessive amount of traffic between a database server and the
newly updated mail server, compared to the baseline data. What is the first action the
administrator should do to investigate the problem?
Check the log to see what software components are producing the excess traffic.
Refer to the exhibit. Users are reporting that they cannot access the Internet. Routers
R1 and R2 are configured with RIP version 2 as shown. If R2 receives a packet with a
destination address on the Internet, how is the packet routed?
The packet is routed to the ISP router and then to network 10.1.1.0/24.
The packet is routed to the ISP router and then to the Internet.
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
The packet will not be routed because R2 does not have a valid default route.
Refer to the exhibit. Both routers are configured using RIPv1. Both routers are
sending updates about the directly connected routes. R1 can successfully ping the
serial interface of R2. The routing table on R1 does not contain any dynamically
learned routes from R2, and the routing table on R2 shows no dynamically learned
routes from R1. What is the problem?
10
11
An employee called the help desk to report a laptop that could not access a web-based
application on the Internet. The help desk technician asked the employee to open a
Windows command prompt and type the ipconfig /all command. Which problem-
solving technique did the technician choose?
top-down
bottom-up
substitution
divide-and-conquer
12
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. Based on the network diagram and the output shown, which
statement is true?
13
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
The protocol type specified in the ACL should be TCP, not IP.
The ACL is applied to the wrong interface, but the right direction.
The ACL is applied to the wrong interface and the wrong direction.
14
Although all networks are reachable, the network administrator notices abnormal
routing behavior after configuring OSPF on each router. According to the partial
output from the debug ip ospf events command, which statement is true about the
contents of the routing table in RA?
15
A network at a large building failed, causing a severe disruption in business activities.
The problem was eventually detected and resolved by replacing a piece of failed
network equipment. Investigation led to the conclusion that a network design problem
was the main cause of the disruption. Loss of a single piece of equipment should not
have been able to cause such a large problem. What two terms best describe this type
of design weakness? (Choose two.)
bottleneck
limited availability
limited scalability
16
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
17
Refer to the exhibit. ABC Company is using the 172.16.0.0/18 network. It is standard
company practice to use the first 50 addresses for switches and servers and assign the
last usable address to the router. The remaining addresses are assigned to the hosts.
After assigning the addresses, the network technician tests connectivity from the host
above and is not able to ping the router. What could be the problem?
The host is not in the same subnet as the switch and router.
18
19
Refer to the exhibit. The network administrator correctly configures RTA to perform
inter-VLAN routing. Using the show vlan command, the administrator verifies that
port Fast Ethernet 0/4 is the first available port in the default VLAN on SW2. The
administrator connects RTA to port 0/4 on SW2, but inter-VLAN routing does not
work. What could be the possible cause of the problem with the SW2 configuration?
20
Refer to the exhibit. The network administrator is unable to ping from the console of
router R3 to host 10.10.4.63. What is the problem?
21
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. A network administrator has implemented subnetting using the
network 192.168.25.0 and a /28 mask. Workstation 1 is not able to ping with
Workstation 2. What is a possible cause for this lack of communication?
The serial connections are using addresses from the LAN subnets.
Workstation 1 is not on the same network that the RTA router LAN interface is on.
22
Which two statements describe when a network administrator should perform a
network baseline? (Choose two.)
It should be performed when all switch Cisco IOS versions are upgraded.
It should be done when all network printers are upgraded to a new model.
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
It should be done whenever an SLA has been signed with a new service provider.