Professional Documents
Culture Documents
CT-V900
GND COM COM +12V Z9-10 Z15-16 Z13-14 Z11-12 NO2 NO1 LK2+ LK1+ NC2 LK2LK1NC1 COM COM COM2 COM1 GND +12V +24V GND Z7-8 Z5-6 Z1-2 Z3-4 B1GND A1+ HIGH LOW BRESET SWITCH
RELAY 2 RELAY 1
EOL
Access during Communication Failure (5 and 6) DIP switches 5 and 6 determine the access to the protected doors during a communication failure.
1 2 3 4 5 6 7 8
ON
HIGH LOW A+
NETWORK
EOL
TX RX
RELAY #2
RELAY #1
ON
CA-A470-A
CA - A470 - A
+
D1NC COM D1NO D2NC COM D2NO
JP120 350mA/700mA
ON 1 2 3 4 5 6 7 8
LOCK #2
LOCK #1
OFF 24V
SUPPLY
12V
12V
24V
EXPANSION PORT
MICRO CHECK
BATT.+ F3: 5A
BATT ENABLE
BATT CHECK
Position Technology
3V ON BATT
+
B1 2 3 4 LOW HIGH S/N E-BUS TMP
OFF
AC PRESENT READER +5V +12V SUPPLY LOGIC +5V +24V SUPPLY LOW BATT
A+ LOW HIGH
TX RX
www.postech.ca
READER #2 DATA
READER #1 DATA
F1: 5A
A.C.IN
E-BUS
R2/KD +24V +12V A2+ B2AC OK AUX OK COMM CHECK BATT BATT TRBL
Door 1
Door 2
R1/KC
R1/KD
R1/KA
R2/KC
R2/KA
R1/KB
R2/KB
R2/D0
R1/D0
R2/0V
R2/5V
R1/0V
R1/5V
R2/D1
R1/D1
OUT4
OUT3
OUT2
OUT6
OUT5
OUT1
BAT+
+24V
+12V
+12V
+24V
GND
GND
BAT-
TMP
AC
AC
Z1 COM Z2 Z3 COM Z4
SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA
READER#2 DATA
A+ BGND
TAMPER TAMPER
Switch
ON 5 6
Setting
5 = off (0) 6 = off (0) 5 = on (1) 6 = off (0) 5 = off (0) 6 = on (1) 5 = on (1) 6 = on (1)
ON
1 2 3 4 5 6 7 8
R2/+5V
SP +12V
SP +12V
R1/+5V
R2/OV
R1/OV
R2/D1
R2/D0
R1/D1
R1/D0
TX RX E-BUS
CA - A470 - A
+
AC OK AUX OK COMM CHECK BATT BATT TRBL SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR EOL A+ B- LOW
HIGH
Z1 COM Z2 Z3 COM Z4
READER#2 DATA
A+ BGND
TAMPER TAMPER
R2/+5V
SP +12V
SP +12V
R1/+5V
R2/OV
R1/OV
R2/D1
R2/D0
R1/D1
R1/D0
TX RX E-BUS
350mA/700mA Battery Charging Jumper The 350mA/700mA Jumper allows you to select the charging current for the backup battery of the 2-Door Expansion Module. Charging the battery at 350mA takes longer, but consumes less power. Charging the battery at 700mA takes less time, but consumes more power. Figure 4: Setting the 350mA/700mA jumper
Jumpers set as 350mA Jumpers set as 700mA
OUT4 OUT3
R2/KPC
R1/KPC
OUT2 OUT1
R2/KPD
R1/KPD
R2/KPB
R1/KPB
R2/KPA
R1/KPA
ON 5 6
ON
1 2 3 4 5 6 7 8
ON
OUT4 OUT3
R2/KPC
R1/KPC
OUT2 OUT1
R2/KPD
R1/KPD
R2/KPB
R1/KPB
R2/KPA
R1/KPA
5 6
Introduction
AC OK AUX OK COMM CHECK BATT BATT TRBL SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR EOL A+ B- LOW
HIGH
Z1 COM Z2 Z3 COM Z4
READER#2 DATA
OUT4 OUT3
R2/KPC
R1/KPC
OUT2 OUT1
R2/KPD
R1/KPD
R2/KPB
R1/KPB
R2/KPA
R1/KPA
R2/+5V
SP +12V
SP +12V
R1/+5V
R2/OV
R1/OV
R2/D1
R2/D0
R1/D1
R1/D0
Door 8
Specications Readers: Keypads: Inputs: Outputs: Lock Outputs: connect 2 per module connect 2 per module 4 standard without ATZ, 1 tamper 6 (open collector) 25 mA Sink 2 lock outputs (Form C relays) each: 15A @ 28VDC (resistive) AC Power: 16VAC, 40VA max. Frequency: 50Hz/60Hz Aux. Current: 500mA (max.) Battery: 12VDC, 7Ah low battery = 10.2VDC low battery restore = 12.2VDC low battery cut-off = 8.5VDC Communication: expansion bus (E-Bus), RS-485, Plug and Play, 3 modules per CTV900-A Operating temp.: 5oC to 55oC (411oF to 133oF)
DIP switches 3 and 4 determine the state of Lock #1 and Lock #2 ONLY during a communication failure between the 2Door Expansion Module and the controller (CT-V900-A). Normally, the lock outputs follow the Lock Control for the CT-V900-A. Therefore, the DIP switches should have the same setting as the Lock Control for the corresponding doors in Centaur. Lock #1 = DIP switch 3 Lock #2 = DIP switch 4
OFF =
In order for new DIP switch settings to take effect, the 2-Door Expansion Modules power must be disconnected and then reconnected.
AC OK AUX OK COMM CHECK BATT BATT TRBL SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR EOL A+ B- LOW
HIGH
AC OK AUX OK COMM CHECK BATT BATT TRBL SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR EOL A+ B- LOW
HIGH
AC OK AUX OK COMM CHECK BATT BATT TRBL SWITCH SW1 ADD 1 SW2 ADD 2 SW3 ADD 4 SW4 ADD 8 SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR EOL A+ B- LOW
HIGH
ON =
DIP switches 1 and 2 determine the 2-Door Expansion Modules address in the network, regardless of the order that they are connected to the controller. Centaur recognizes the doors according to the DIP switch settings as shown in Figure 1.
Energized: During a communication failure, the normal state of the lock output is Energized. When Lock #1 or Lock #2 is activated, power is removed from the corresponding lock output to unlock the door. Activation depends on the setting of the DIP switches 5 & 6 (Access during Communication Failure).
Z1 COM Z2 Z3 COM Z4
READER#2 DATA
A+ BGND
TAMPER TAMPER
Z1 COM Z2 Z3 COM Z4
READER#2 DATA
A+ BGND
TAMPER TAMPER
Z1 COM Z2 Z3 COM Z4
READER#2 DATA
OUT4 OUT3
OUT2 OUT1
OUT4 OUT3
OUT2 OUT1
OUT4 OUT3
R2/+5V
R1/+5V
R2/+5V
R1/+5V
R2/+5V
R1/+5V
SP +12V
SP +12V
SP +12V
SP +12V
SP +12V
SP +12V
R2/OV
R1/OV
R2/OV
R1/OV
R2/OV
R1/OV
R2/D1
R2/D0
R1/D1
R1/D0
R2/D1
R2/D0
R1/D1
R1/D0
R2/D1
R2/D0
R1/D1
R1/D0
TX RX E-BUS
TX RX E-BUS
OUT2 OUT1
R2/KPC
R1/KPC
R2/KPC
R1/KPC
R2/KPC
R1/KPC
R2/KPD
R1/KPD
R2/KPD
R1/KPD
R2/KPD
R1/KPD
R2/KPB
R1/KPB
R2/KPB
R1/KPB
R2/KPB
R1/KPB
R2/KPA
R1/KPA
R2/KPA
R1/KPA
R2/KPA
R1/KPA
De-energized: no power in normal state; requires power to activate. Energized: power in normal state; remove power to activate.
High/Low Bias Jumpers Place the A+ and B- jumpers on LOW only if the 2-Door Expansion Module is at the beginning (Start Point) of the E-bus Network. Otherwise, place the A+ and B- jumpers on HIGH (see Figure 2 and Figure 3).
DIP Switches
De-energized: During a communication failure, the normal state of the lock output is De-energized. When Lock #1 or Lock #2 is activated, power is applied to the corresponding lock output to unlock the door. Activation depends on the setting of the DIP switches 5 & 6 (Access during Communication Failure).
EOL
Connected to the CT-V900 controllers expansion bus, Maximum 3 per controller, the 2-Door Expansion Module (CA-A470-A) supports two readers, two BCD keypads, four zone inputs, 6 outputs and two locking devices.
ON
CA - A470 - A
A+ BGND
TAMPER TAMPER
5 6
ON
1 2 3 4 5 6 7 8
TX RX E-BUS
Door 7
Activate Output on Communication Failure (7) DIP switch 7 determines if OUT5 and OUT6 will pulse during a communication failure. When DIP switch 7 placed in the ON position, the outputs on the device(s) connected to the OUT5 and OUT6 terminals will pulse. For example, the buzzer on the reader can pulse to advise users that a communication failure has occurred.
1 2 3 4 5 6 7 8
ON
Programming in Centaur Using the Centaur Access Control Software, program the inputs, outputs, readers, and keypads connected to the 2-Door Expansion Module. The options are explained in the Centaur Access Control Software Reference Manual. Centaur will identify the 2-Door Expansion Module by its address, DIP Switches 1 & 2, and will recognize the devices as follows:
Address 1 Address 2 Address 3
Doors Keypad/Reader 1 Keypad/Reader 2 Inputs Z1 Z2 Z3 Z4 Outputs OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 Door 3 Door 4 Input 17 Input 18 Input 19 Input 20 Output 7 Output 8 Output 9 Output 10 Output 11 Output 12 Door 5 Door 6 Input 21 Input 22 Input 23 Input 24 Output 13 Output 14 Output 15 Output 16 Output 17 Output 18 Door 7 Door 8 Input 25 Input 26 Input 27 Input 28 Output 19 Output 20 Output 21 Output 22 Output 23 Output 24
CT-V900
LOCK #1
12V 24V
MICRO CHECK
www.postech.ca
AC PRESENT READER +5V +12V SUPPLY LOGIC +5V +24V SUPPLY LOW BATT
LOCK #2
12V 24V
EXPANSION PORT
RELAY #1
RELAY 2
RELAY #2
+12V GND Z1-2 COM Z3-4 Z5-6 COM Z7-8 +12V GND Z9-10 COM Z11-12 Z13-14 COM Z15-16 HIGH LOW A+ A1+ B1DEF/RUN 9.6K/19.2K ADD 32 ADD 16 ADD 8 ADD 4 ADD 2 ADD 1
#3
OFF
RING
READER #1 DATA
ON
READER #2 DATA
EOL Jumper START POINT EOL = On High/Low Bias Jumpers A+ = Low END POINT B- = Low
ON 3V
E-BUS
TX RX
BATT
NETWORK
TX RX
EOL
BRESET SWITCH
+
B1 2 3 4 LOW HIGH S/N E-BUS
CA-A470-A
Position Technology
CA - A470 - A
CA-A470-A
Position Technology
CA - A470 - A
CA-A470-A
Position Technology
CA - A470 - A
A+ BGND
TAMPER TAMPER
TX RX E-BUS
Doors cannot be defined as Door Type Elevator (Door Properties window, General tab, Door Type: Elevator) and the module does not support Interlock Inputs (Door Properties window, Inputs and Outputs tab, Interlock Input). Other modules in the system cannot activate the 2-Door Expansion Modules outputs. The 2-Door Expansion Module does not support Zone Doubling (see Figure 6).
ON
1 2 3 4 5 6 7 8
Figure 5: CA-A470-A indicators Green aC OK LED: ON = AC power OFF = Power failure Green aUX OK LED: ON = Auxiliary power OFF = Auxiliary power failure Red COMM LED: ON = Communication failure OFF = OK Green CHeCK baTT LED: ON = Battery verification in progress (every minute) Red baTT Trbl LED: ON = Battery low or disconnected
CA-A470-A 2-Door Expansion Module
LOCK#1
CDV Americas
- + - +
www.cdvamericas.com
Electromagnetic LOCK 2
Pull Station
EMERGENCY
Green sTaTUs LED: Flash = Module OK Slow flash = Communication failure (see also comm LED) Green lock#1 and lock #2 LEDs: ON = Relay activated.
PULL
DOWN
Transformer 16VAC-40VA
+
STATUS
LOCK#2
OUT4 OUT3
OUT2 OUT1
JP120 350mA/700mA
ON 1 2 3 4 5 6 7 8
SWITCH SW1 ADD 1 SW2 ADD 2 SW3 L1Energize SW4 L2Energize SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA
STATUS LOCK#2
JP120 350mA/700mA
ON 1 2 3 4 5 6 7 8
+
AC OK AUX OK COMM CHECK BATT BATT TRBL
4
BACKUP 2 1 0 0 NO CARD 0 1 2 CARDS 1 0 ALL CARDS 1 1 UNLOCK DOOR
SWITCH SW1 ADD 1 SW2 ADD 2 SW3 L1Energize SW4 L2Energize SW5 BACKUP1 SW6 BACKUP2 SW7 PULSE 5&6 SW8 N/D READER#1 DATA
READER#2 DATA
EOL
OUT4 OUT3
OUT2 OUT1
READER#2 DATA
A+ BGND
EOL
TX RX E-BUS
TMP TMP
KEYPAD 2
KEYPAD 1
The 2-Door expansion module (CA-A470-A ), does not support zone doubling. NC INPUT CONNECTION ATZ 2R CONNECTION ATZ 3R CONNECTION
Green reader#2 data and reader#1 data LED: Long flash = Receiving card read Short flash = Receiving card read, but the system does not recognize the cards format OFF = Not receiving card read
Red tx LED and green rx LED: ON = Communication OK (may flicker) OFF = Communication failure
OR
Input 1 1K
OR
Input 1 1K
EOL 1K
The reader LEDs can be used to verify the readers connections and programming. If no flashing occurs when a card is presented to the reader, the reader may be installed incorrectly. A short flash indicates that the reader is correctly installed, but the card is the wrong type or that the reader was incorrectly programmed.
Warranty
CDV Group (Seller) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system and shall not be responsible for circumstances resulting from the products inability to operate. Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Sellers option, any product not meeting the specifications. Returns must include proof of purchase and be within the warranty period. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold. Notwithstanding the preceding paragraph, the Sellers maximum liability will be strictly limited to the purchase price of the defective product. Your use of this product signifies your acceptance of this warranty. BEWARE: Dealers, installers and/or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on the Seller. 2001-2007 CDV Group. All rights reserved. Specifications may change without prior notice. Centaur is a trademark or registered trademark of CDV Group. or its affiliates in Canada, the United States and/or other countries.
JUMPER SEttINGs
1 2 3
BattERY CHaRGING Charging the battery at 350mA (jumper ON) takes longer, but consumes less power. Charging the battery at 700mA (jumper OFF) takes less time, but consumes more power. HIGH/LOw BIas Place the A+ and B- jumpers on LOW only if the 2-Door Expansion Module is at the beginning (Start Point) of the E-bus Network. Otherwise, place the A+ and B- jumpers on HIGH EOL Place the EOL jumper ON if the 2-Door Expansion Module is at the Start Point or at the End Point of the E-bus Network. Otherwise, place the EOL jumper OFF.
4
CA-A470-A address
ADD1 and ADD2 determine the 2-Door Expansion Modules address, regardless of the order that they are connected to the controller.
PULSE 5&6 L1 Energize L2 Energize BACKUP1 BACKUP2
1
OFF ON OFF
1 2 3
OFF OFF ON
Specifications may change without prior notice. Printed in Canada - 20/01/07 - CA-A360-A_IE
+
2
ADD 1 ADD 2
TEcHNIcaL SUPPORt
Always consult the regulatory agency in your area for existing regulations regarding doors designated as emergency exits.
A+ BGND
3
TX RX E-BUS
TMP TMP
N/D
ON
OFF