Professional Documents
Culture Documents
: Date:
1 Input data
Anchor type and diameter: Effective embedment depth: Material: Evaluation Service Report: Issued I Valid: Proof: Stand-off installation: Anchor plate: Profile: Base material: Reinforcement: ETA 98/0001 08.05.2013 | 20.02.2018 design method Extended ETAG (No. 001 Annex C/2010) without clamping (anchor); restraint level (anchor plate): 2,00; eb = 10 mm; t = 8 mm Hilti Grout: , multipurpose, fc,Grout = 30,00 N/mm2 lx x ly x t = 300 mm x 300 mm x 8 mm; (Recommended plate thickness: not calculated) Pipe; (L x W x T) = 168 mm x 168 mm x 9 mm cracked concrete, C20/25, fcc = 25,00 N/mm2; h = 140 mm no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm) no longitudinal edge reinforcement Reinforcement to control splitting according to ETAG 001, Annex C, 5.2.2.6 present. Geometry [mm] & Loading [kN, kNm] HST M12 hef = 70 mm, hnom = 80 mm
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Compression 1 x 3
Tension
3.3 Concrete Breakout Strength Ac,N [mm2] 80975 ec1,N [mm] 0 N0 Rk,c [kN] 21,084
2 A0 c,N [mm ] 44100
scr,N [mm] 210 yec2,N 1,000 NSd [kN] 0,010 ys,N 1,000 yre,N 1,000 k1 7,200
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
VM Rk,s = aM * MRk,s / l [kN] 10,498 4.2 Pryout Strength Ac,N [mm2] 147500 ec1,V [mm] 0 gM,c,p 1,500
2 A0 c,N [mm ] 44100
bV 0,147
a 1,500
Status OK
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this calculation! The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
7 Warnings
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the loading! Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software considers that the grout is installed under the anchor plate without creating air voids and before application of the loads. The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C! The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed to ensure a proper installation.
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
8 Installation data
Anchor plate, steel: Anchor type and diameter: HST, M12 Profile: Pipe; 168 x 168 x 9 mm Installation torque: 0,060 kNm Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm Plate thickness (input): 8 mm Hole depth in the base material: 95 mm Recommended plate thickness: not calculated Minimum thickness of the base material: 140 mm Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
8.1 Required accessories Drilling Suitable Rotary Hammer Properly sized drill bit Cleaning Manual blow-out pump y Setting Torque wrench Hammer
150
150
25 1 3 125 150
125 2 25 25 125 125 25 Coordinates Anchor [mm] Anchor 1 2 3 4 x -125 0 125 0 y 0 -125 0 125 c-x c+x c-y c+y Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
150
www.hilti.com Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan