Profle Speccoats has been manufacturing and distributing paint coatings and application equipment to the market since 1997. Our Range Automotive & Light Industrial Decorative Coatings Equipment Floor Coatings FRP Gratings Furniture & Shop Fitting Finishes Maintenance, Repair and Overhaul Systems Pipeline Industry Protective & Anti-Corrosive Coatings Specialized Industrial Coatings Product Data Sheets and Material Safety Data Sheets available on our website. Visit www.speccoats.co.za For more information on our product range and for technical support please contact our technical department: 0861 37 2468 The information and images contained in this brochure are intended as a guide only. Please refer to the datasheet for each individual product for full instructions. Index pg Colour Standards 4 Surface Preparation Degrees of Cleanliness 5 Mechanical Removal of Surface Contaminants 6 Products for Removal of Surface Contaminants 7 Protective & Anti-Corrosive Coatings Acrylics 9 Alkyds 10 Cementitious 12 Chlorinated Rubbers 13 Ceramic Epoxies 14 Mastic Epoxies 15 Phenolic Epoxies 15 Solvented Epoxies 16 Solventless Epoxies 19 Glass Flake 20 High Temperature Coatings 21 Polyureas 23 Polyurethane/Urea 23 Polyurethanes 24 Vinyls 27 Zinc Coatings 28 Equipment Testing Equipment 30 Application Equipment 33 Colour Standards 4 RAL NCS is the understandable international colour order system for colour selection, specifcation, communication and the control of colour in design, architecture, research, marketing and manufacturing. The NCS system is based on how people see colour. This colour range consists of close to 2000 colours. Since 1927 RAL has created a concise language when it comes to the use of colour. We have standardized colour numbers and names for all RAL colours. RAL Colour standards are being used in the coatings industry. The South African Bureau of Standards colour system is a system all paint manufacturers & applicators recognize. It is a colour coding system used by many industries. NCS SABS Degrees of Cleanliness of Blast Cleaned Surfaces Condition of Steel Grade A Grade B Grade C This is often referred to as whip blasting. Cleaning to this standard required that loose mill scale, loose rust and foreign matter are removed. Grade A Grade B Grade C Steel where mill scale has started to fake and light rusting occurs Steel where all mill scale has faked of and complete rusting has taken place Steel where pitting and complete rusting has occurred Specs: Sa 1, NACE-4 and SSPC-SP-7 Grade A Grade B Grade C Specs: Sa 2, NACE-3 and SSPC-SP-6 Cleaning to this standard requires that mill scale, rust and foreign particles are substantially removed and that grey metal is visible. Cleaning to this standard requires that mills scale, rust and foreign particles are removed to such a degree that the only traces remaining are slight stains in the form of spots or strips Grade A Grade B Grade C Specs: Sa 2 1 /2 , NACE-2 and SSPC-SP-10 Cleaning to this standard requires the entire removal of all mill scale, all rust and all foreign particles. The cleaned surface shall have a uniform metallic colour. Grade A Grade B Grade C Specs: Sa 3, NACE-1 and SSPC-SP-5 Near White Blast Cleaning White Metal Blast Cleaning 5 Surface Preparation Light Blast Cleaning Medium Blast Cleaning Surface Preparation Mechanical Removal of Surface Contaminants 6 Needle/Chisel De-scaling A needle gun has a set of very fne chisels known as needles. The tool forces these needles against a work surface at variable speeds up to around 5000 times per minute by means of compressed air. Removes rust, loose mill scale & paint leaving bare metal A process of forcibly propelling a stream of abrasive material against a surface under high pressure which removes surface contaminants and provides a clean, keyed surface for coating. Blast Pots Hose Nozzles Vacu Blast Blasting Safety Equipment Hollow Blast Spin Blast Abrasive Blast Cleaning Grinders, Pneumatic Sanders & Abrasives Used to remove rust, contamination, mill scale, weld spatter and to grind and fettle high points smooth and round so paint can adhere. This method also provides a sufcient profle for certain coatings. Abrasive Sheets/Sandpaper Abrasive Discs Abrasive Flap Wheels Abrasive Pads Abrasive Blasting Materials Grinders Pneumatic sanding Machines Water Jetting is a surface preparation method which uses high-energy water to remove coatings, corrosion products and other surface contamination such as oil/grease/dust/grime/grease etc. The energy of the water striking the surface is used to achieve its cleaning afect. Water jetting does not provide a surface profle like abrasive blasting, and fash rusting will occur immediately. In this case, specialist coating systems are required. Blast Pots Hose Nozzles Vacu Blast Blasting Safety Equipment Hollow Blast Spin blast Water Jetting Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Surface Preparation 7 Surface Contamination Removal Galvanized Iron Cleaner Hydrosolve Paint Stripper A ready to use, single pack and non mixing liquid designed to react with & clean galvanized iron. Emulsifes grease and oil on the surface. Rinsed of with drinking quality water A ready to use, single-pack, water/detergent solvented degreaser that quickly dissolves grease & oils of all surfaces. Used to degrease components prior to painting Removes all mineral oils, cutting oils & light greases from the surfaces leaving the surfaces clean for painting Will lift freshly painted enamels & undercoats A ready to use, single pack liquid in a heavy paste form designed to remove old paint flms from a variety of surfaces. Easy to use GalvKleen Paste A ready to use, single-pack paste which utilizes a abrasive & detergent mixture to clean galvanized iron. Emulsifes with water to provide a water-break-free surface after rinsing with drinking quality water A ready to use, single-pack, solvented degreaser that quickly dissolves grease & oils of metal surfaces. Used to degrease metal sheet work prior to painting. Removes all mineral oils, cutting oils & light greases from the surfaces leaving the surfaces clean for painting Steel & Plate Degreaser A dilute etch solution in a liquid form designed for removal of cement laitance. Rinsed of with drinking quality water Neutralised with Speccoats Concrete Neutraliser Concrete Etch Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre Green Detergent & Acid based Liquid Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre Red Oxide Detergent & Abrasive mixture paste Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre Clear Solvent-Based thin liquid Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre Blue Water/Detergent solvent based Kit Size (L) Application Colour Product Type 0.5, 1 and 5 Litre Clear Paint Remover Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre Clear Acid Etch Solution Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Surface Preparation Surface Contamination Removal Dust & Debris Removal Protecting It often accurs that a surface is dusty, greasy, dirty or generally contaminated. Brooms and Brushes Cleaning Rags Tack Rags Mops Scotchbrite Sponges Vacuum Systems Air Guns When it comes time to paint, the job can get messy, we sell the following products to help protect surfaces which need to stay clean. Masking Tape Static Plastic Sheeting (Fine plastic sheeting which adheres statically to surfaces without the use of masking tape) Plastic Drop Sheets Concrete Neutraliser Chlor*Wash A powder which is dissolved in a prescribed quantity of water & poured on an acid etched surface to neutralize any remaining acid. Rinsed of with drinking quality water Brings acidic levels to a neutral level prior to applying coatings An organic bonding chemical blend which aids in the removal of chlo- rides, sulphates & surface reacted salts. Highly concentrated Very cost efective & easy solution to removing chlorides, sulphates & surface reacted salts Kit Size (L) Application Colour Product Type 1, 5 and 20 Litre White Powder Neutralizer Kit Size (L) Application Colour Product Type 0.5, 1 and 5 Litre Blue Chemical Blend 8 Acrylics Water Based Galvanized Primer A one component water based primer for galvanized metallic substrates. Excellent adhesion to galvanized metallic substrates including suitably prepared hot-dip galvanized substrates Excellent adhesion to ceramic and plastic materials Contains a unique blend of anti-corrosive pigments which retard corrosion of metallic substrates Can be over coated with water-based and solvent-based topcoats Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide and Grey Acrylic Co-Polymer Emulsion Water Based Metal Primer A one component water based primer for metallic substrates. Excellent adhesion to galvanized metallic substrates including suitably prepared hot-dip galvanized substrates Excellent adhesion to ceramic and plastic materials Contains a unique blend of anti-corrosive pigments which retard corrosion of metallic substrates Can be over coated with water-based and solvent-based topcoats Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide and Grey Acrylic Co-Polymer Emulsion Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 9 Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings Alkyds 10 QD Enamel A one component quick drying gloss enamel suitable for many production items such as conveyor idlers, gas cylinders, automobile parts steel drums, steel furniture etc. Items sprayed with this fnish are immediately attractive Fast drying for quick turnaround times Available in aluminium fnish Available as ready for use (spraying viscosity) Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Modifed Alkyd AD Enamel A one component synthetic solvented air drying enamel, used as general purpose enamel for spraying truck bodies, trucks, buses, general transport, farm implements, garden furniture and wherever a high gloss, durable fnish is required on either metal or woodwork. Good quality gloss fnish Dust free in 40-50 minutes Good durability in exterior exposure conditions Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Modifed Alkyd Alkyd Metal Primer A one component solvented zinc phosphate alkyd primer for metallic substrates. Used as a universal primer on a variety of substrates. Excellent adhesion to metallic substrates including hot dip galvanized substrates Excellent adhesion to ceramic and plastic Excellent exterior durability and corrosion resistance Can be over coated with emulsion and solvent based topcoats Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide and Grey Alkyd Zinc Phosphate QD Zinc Phosphate Primer A one component solvented, fast drying zinc phosphate anti-corrosive primer for use under QD Enamels and AD Enamels. Contains zinc phosphate anti-corrosive pigment Provides corrosion resistance to steel Fast drying primer for industrial systems Excellent adhesion to abrasive blast cleaned steel Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Red Oxide, Grey and Yellow Oxide Modifed Alkyd Resin QD Primer A one component solvented fast drying pigmented primer for use under QD Enamel and other Industrial top coats. Very fast drying Quick over-coating allows for faster turnaround times Available as ready for use (spraying viscosity) Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Red Oxide and Grey Alkyd QD Primer Low V.O.C. A one component solvented low V.O.C. fast drying pigmented primer for use under QD Enamel and other Industrial top coats.
Low V.O.C. Fast drying Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Red Oxide and Grey Water Modifed Alkyd Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 11 Alkyds Universal Gloss Enamel One component solvented, high quality universal gloss enamel for interior and exterior applications. Excellent fnish with good weather resistance Excellent interior and exterior durability and wash ability High opacity and low odour Kit Size (L) Application Colour Product Type 5 and 20 Litre RAL, NCS and SABS Long Oil Alkyd Solvent Based AD Enamel A one component synthetic solvented air drying enamel, used as general purpose enamel for spraying truck bodies, trucks, buses, general transport, farm implements, garden furniture and wherever a high gloss, durable fnish is required on either metal or woodwork. Good quality gloss fnish Dust free in 40-50 minutes Good durability in exterior exposure conditions QD Enamel Low V.O.C. A one component low V.O.C. quick drying gloss enamel suitable for many production items such as conveyor idlers, gas cylinders, automobile parts steel drums, steel furniture etc. Items sprayed with this fnish are immediately attractive Water Modifed which lower the V.O.C. Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Water Modifed Alkyd Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Modifed Alkyd QD Enamel WB A one component water-based quick drying gloss enamel suitable for many production items such as conveyor idlers, gas cylinders, automobile parts, steel drums, steel furniture etc. Water Based, Zero V.O.C. Quick drying Available in aluminium fnish A hard, beautiful coating Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Modifed Alkyd Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Cementitious Protective & Anti-Corrosive Coatings 12 Patching Compound A blend of graded silicas and fast setting cements modifed with a polymer and cure enhancing chemicals. A fast curing cement compound for fxing holes in concrete & masonry. Easy to use Simply add water to desired consistency Can take light trafc after 4 hours Can be thinned for use as a fairing compound Cures to an extremely tough, non shrink, hard state which can be over coated with fooring e.g. tiles the following day Kit Size (kg) Application Colour Product Type 10 and 25 kg Dark Grey Cementitious Irabond CR94 Cementitious waterproofng compound can be used as a faring or levelling coat on concrete or masonry prior to the application of either Aqualine or Polyureas. Resists ground water back pressure for in ground structures UK Secretary of State for the environment (DWI) Approved Can be used on its own to waterproof stable concrete substrates Kit Size (kg) Application Colour Product Type 25 kg Pink Cementitious Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 13 Chlorinated Rubbers Chlorinated Rubber Primer One component solvented, plasticized chlorinated rubber intermediate coat suitable for steel structures, shipbuilding, mechanical and automotive engineering, transportation and the protection of buildings in chemical plants, coastal and marine environments. Excellent adhesion Chemical resistant coating Exhibits good fexibility and Weatherability Kit Size (L) Application Colour Product Type 5 and 20 Litre Grey & Red Oxide Chlorinated Rubber Chlorinated Rubber HB Intercoat One component solvented, plasticized chlorinated rubber intermediate coat suitable for steel structures, shipbuilding, mechanical and automotive engineering, transportation and the protection of buildings in chemical plants, coastal and marine environments. Can be built up to a high build Chemical Resistant coating Exhibits good fexibility and Weatherability Chlorinated Rubber Enamel Finishcoat One component solvented, plasticized chlorinated rubber enamel fnishcoat suitable for steel structures, shipbuilding, mechanical and automotive engineering, transportation and the protection of buildings in chemical plants, coastal and marine environments. Chemical Resistant coating Exhibits good fexibility and Weatherability Kit Size (L) Application Colour Product Type 5 and 20 Litre Light Grey Chlorinated Rubber Kit Size (L) Application Colour Product Type 5 and 20 Litre Various Chlorinated Rubber Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 14 Kit Size (L) Application Colour Product Type 0.75 and 4 Litre White Ceramic Filler Epoxy Irathane CC4500 A 100% Solids, two component ceramic flled epoxy, for direct application to concrete or steel. SANS 1217 Type 1B Certifed per ANSI/NSD Standard 61 Excellent abrasion resistance Produces hard slick surfaces Resistant to dilute acids & alkalis Ceramic Epoxies Devcon Brushable Ceramic Ceramic flled, brushable epoxy the provides a smooth protective barrier against abrasion, erosion and chemical attack. Low friction surface for operation efciency Rebuilds and seals heat exchanger tubes and protects pump casings and fange faces Kit Size (gm) Application Colour Product Type 500 gm Red, Blue and White Ceramic Epoxy Devcon Sprayable Ceramic A reinforced Sprayable, ceramic epoxy, which is chemically resistant for surfaces that require an exceptionally smooth fnish. Very low friction surface Protects tanks, pumps, blades, valves etc exposed to erosion and corrosion Kit Size (kg) Application Colour Product Type 10 kg Blue and Grey Ceramic Epoxy Online Brushable Ceramic A reinforced Sprayable, ceramic epoxy, which is chemically resistant for surfaces that require an exceptionally smooth fnish. Very low friction surface Protects tanks, pumps, blades, valves etc exposed to erosion and corrosion Kit Size (kg) Application Colour Product Type 10 kg Blue and Grey Ceramic Epoxy Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 15 Phenolic Epoxies Kit Size (L) Application Colour Product Type 5 Litre Kits Beige Phenolic Epoxy Phenshield 3050 Primer Two component solvented modifed phenolic, matt fnished, pigmented primer that has excellent adhesion to steel and excellent resistance to a wide range of solvents, alkalis and acid vapours when over coated with Speccoats Phenshield 3050 Finish. Cures to a hard matt surface Suitable for damp, chemical environments such as pulp & paper mills Protection against severe splash, spillage and fume conditions Kit Size (L) Application Colour Product Type 4 Litre Kits Various Phenolic Epoxy Phenshield 3050 Finish Two component solvented modifed phenolic, pigmented fnish coat which sets to a hard, tough fnish with very good abrasion resistance and a glossy surface which is chemically resistant and easily cleaned. Excellent chemical resistance Cures to a hard resilient surface which is abrasion resistant Suitable for damp, chemical environments such as pulp & paper mills Protection against severe splash, spillage and fume conditions Pipetank 175 A two component solvented phenolic epoxy formulated to provide high acid, chemical & abrasion resistance in immersion conditions. Up to 90C chemical immersions resistance depending upon the chemical involved Excellent resistance to abrasion & mechanical damage Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Grey Phenolic Epoxy Mastic Epoxies Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Black and Brown Coal Tar Epoxy Pipetank Coal Tar Epoxy A two component solvented coal tar modifed epoxy pigmented fnish for the protection of steel & concrete. Self priming, high solids epoxy coating Develops a hard coating with a very good water and corrosion resistance Good chemical resistance Good resistance to wet and salt water environments Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits RAL, SABS, Red Oxide and Grey Epoxy Mastic Pipetank 8900 Mastic Epoxy A two component solvented high solids rapid cured epoxy mastic coat- ing applied as a coating over mechanically steel or suitably prepared concrete surface ofering excellent corrosion protection. Surface tolerant, self priming, high solids epoxy coating Develops a hard coating with very good solvent and corrosion resistance Good resistance to chemicals and wet environments Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 16 Solvented Epoxies Kit Size (L) Application Colour Product Type 4.5 and 20 Litre Kits Water Blue and Grey Polyamide Cured Epoxy Pipetank 2300 RW Two component, solvented polyamide cured epoxy formulated as a high performance multi-layer chemical resistant coating and lining designed for raw, process and mining water containment and transport. Applied directly onto abrasive blast cleaned steel & is self priming Excellent adhesion, permeation resistance and corrosion protection Good fexibility and water resistance Good chemical resistance Pipetank 8800 HS A two component solvented high solids rapid cured epoxy pigmented coating formulated for use as a multi layer coating and lining for contact with Potable Water & many other liquids held in tank storage. Applied directly onto blast cleaned steel and is self priming High solids enables contractor to apply higher flm thicknesses per coat Good chemical resistance and resistance to aviation fuels In accordance with SANS 1217 Type 1A requirement Kit Size (L) Application Colour Product Type 4 and 20 Litre Red Oxide, Grey, Black and Water Blue Epoxy Pipetank 8800 A two component solvented epoxy which cures with a unique rapid cure hardener formulated for use a high performance lining for pipes & tanks for immersion in Potable Water. SANS 1217 Type 1A Suitable for contact with Potable Water & many other liquids held in tank storage Very rapid curing Good chemical resistance & resistance to aviation fuels etc Immersion temperature resistant up to 80C Kit Size (L) Application Colour Product Type 4 and 20 Litre Water Blue & Grey Epoxy Cured with Rapid Cure Hardener Kit Size (L) Application Colour Product Type 3 and 15 Litre Kits Clear Amido-amine Epoxy Pipetank Rustbond Two component solvented ambient curing amido-amine epoxy clear primer formulated as a cross-linking penetrating sealer with excellent wetting properties which fxes rust to an extent that it can be over coated. High solids, low viscosity clear primer/sealer Cures to a hard fexible coating with excellent adhesion on rusty substrates Used as a primer/sealer for clean, oil free galvanized and concrete surfaces Pipetank 16 W Two component solvented amine cured epoxy formulated as a high performances lining for steel tanks & pipes containing hot water. Withstands continuous immersion temperatures up to 120C & a dry heat resistance up to 150C Excellent adhesion & corrosion protection when applied to abrasive blast cleaned steel Provides long term protection of hot water tanks & condensate return tanks Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide & Grey Amine Cured Epoxy Pipetank 2300 A two component solvented polyamide cured epoxy formulated for use as a multi-layer coating & lining on steel pipelines & tanks, for immersion in Potable Water. SANS 1217 Type 1A This system has been used extensively for water pipelines in Southern Africa since 1973 Expected service life is in excess of 20 years Applied directly onto blast cleaned steel Excellent adhesion, permeation resistance, corrosion protection & water resistance in immersion conditions up to 80C Kit Size (L) Application Colour Product Type 4 and 20 Litre Water Blue & Grey Polyamide Cured Epoxy Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 17 Solvented Epoxies Pipetank EA 900 A two component solvented amine cured epoxy primer & Finishcoat designed for many types of surfaces i.e. aluminium, galvanizing, steelwork, concrete, GRP and Phenolic Sheeting to provide long term corrosion protection. Good resistance to abrasion and mechanical damage Excellent adhesion on correctly prepared surfaces Suitable for contact with potable water Fully cured coating ofers outstanding resistance to a wide range of industrial chemicals Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Red Oxide Amine Cured Epoxy Pipetank EA 900 HB Primer - Intercoat A two component solvented, high build, amine cured epoxy formulated as a high performance general purpose primer intermediate coat for corrosion resistance on steelwork and other metal substrates or as an intermediate coat of Speccoats Pipetank EA 900 or other priming systems Excellent adhesion on correctly prepared surfaces Good resistance to aqueous solutions and a wide range of industrial chemicals Good resistance to abrasion and mechanical damage Kit Size (L) Application Colour Product Type 5 and 20 Litre Grey & Buf Amine Cured Epoxy Pipetank EA 900 HB PW Primer - Intercoat A two component solvented, high build, amine cured epoxy formulated as a high performance primer intermediate coat suitable for contact with Potable Water for corrosion resistance on steelwork and other metal substrates or as an intermediate coat of Speccoats Pipetank EA 900 or other priming systems. Suitable for contact with Potable Water Excellent adhesion on correctly prepared surfaces Good resistance to aqueous solutions and a wide range of industrial chemicals Good resistance to abrasion and mechanical damage Kit Size (L) Application Colour Product Type 4 and 20 Litre Grey & Buf Amine Cured Epoxy Kit Size (L) Application Colour Product Type 15 Litre Kits Red Oxide and Grey Polyamide Cured Epoxy Pipetank 8880 Primer A two component solvented polyamide cured epoxy zinc phosphate pigmented coating formulated as a high performance, self priming, high build anti-corrosive coating for use in shops where fast turnaround time is required. Excellent adhesion on correctly prepared surfaces Short recoat time for fast turnaround time High solids coating, which can be top coated using epoxies, polyurethanes or alkyds Pipetank EA 400 A two component solvented epoxy pigmented coating formulated as a lining for the protection of pipelines carrying a wide range of petro- chemical products including aviation fuel, Kerosene and crude oil mixtures. Recognised worldwide as the standard coating for aviation fuel lines Unafected by crude oil mixtures, petrochemical product mixtures and most industrial chemicals Excellent corrosion resistance under aggressive immersion conditions Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide Amine Cured Epoxy Pipetank EA 500 A two component solvented high build epoxy pigmented coating formulated as a higher build, chemical resistant protective coating in immersion conditions. Proven resistance against a wide range of petroleum products. Applied as a lining for aviation fuel tanks and vessels Good resistance to abrasion and mechanical damage Approved worldwide for contact with aviation fuel Good resistance to a wide range of industrial chemicals and solvents Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide Amine Cured Epoxy Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 18 Solvented Epoxies Prime EA 900 Holding Primer Two component solvented epoxy holding / welding primer. A general purpose holding primer on blast cleaned steel & other metal surfaces Used as a weld-able, prefabrication primer followed by a full painting system Provides a high degree of corrosion protection in one thin coat Can be over coated in up to three months Excellent adhesion onto correctly prepared surfaces Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Red Oxide Epoxy Surtol Aluminium Two component solvented, high solids, modifed epoxy coating containing aluminium anti-corrosive pigments developed as a high performance coating that can be applied to hand prepared surfaces and can be over coated by various topcoats. Used on surfaces which cannot be abrasive blast cleaned Provides good corrosion protection to wire brushed rusty steelwork Excellent adhesion and impact resistance Resistant to humidity salt water and exterior exposure conditions Kit Size (L) Application Colour Product Type 10 Litre Kits Aluminium Aluminium Epoxy Pipetank EA 900 HB Z/P Primer - Intercoat A two component solvented, high build, amine cured epoxy pigmented with zinc-phosphate anti-corrosive pigment, formulated as a high performance primer intermediate coat for corrosion resistance on steelwork and other metal substrates or as an intermediate coat of Speccoats Pipetank EA 900 or other priming systems. Excellent adhesion on correctly prepared surfaces Good resistance to aqueous solutions and a wide range of industrial chemicals Good resistance to abrasion and mechanical damage Pipetank EA MIO Primer - Intercoat A two component solvented amine cured epoxy, pigmented with lamel- lar micaceous iron oxide which has been formulated to provide a highly efective barrier coating that can be used as an intermediate coat over primers or as a maintenance coat over previously painted surface. The lamellar MIO fakes provide excellent resistance to water permeation. Good chemical resistance and corrosion resistance The MIO provides reinforcement to the flm as well as enhancing abrasion and erosion resistance. The faky nature of the pigment provides a shielding efect against UV radiation and aggressive weathering afects Kit Size (L) Application Colour Product Type 4 and 20 Litre Kits Red Oxide and Metallic grey Amine Cured MIO Epoxy Pipetank EA MIO Z/P Primer - Intercoat A two component solvented amine cured epoxy, pigmented with lamellar micaceous iron oxide and zinc phosphate anti-corrosive pigment, formulated to provide a highly efective barrier coating that can be used as an intermediate coat over primers or as a maintenance coat over previously painted surface. The lamellar MIO fakes provide excellent resistance to water permeation. Contains corrosion inhibiting zinc phosphate pigment Good chemical resistance and corrosion resistance The MIO provides reinforcement to the flm as well as enhancing abrasion and erosion resistance. The faky nature of the pigment provides a shielding efect against UV radiation and aggressive weathering afects Kit Size (L) Application Colour Product Type 5 and 20 Litre Grey & Buf Amine Cured Epoxy Kit Size (L) Application Colour Product Type 4 and 20 Litre Kits Red Oxide and Metallic grey Amine Cured MIO Epoxy Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 19 Solventless Epoxies Pipetank 151 A two component surface tolerant solvent free epoxy formulation that provides long-term corrosion protection to steel & concrete surfaces in immersion conditions & can be applied under water. Used as a repair & make good coating for existing epoxy linings Used as a high quality lining for tanks and pipe, applied directly onto suitably prepared steel Has provided good service in immersion condition for more than 20 years Kit Size (L) Application Colour Product Type 200 ml, 1 & 4.5 L Kits & Various Cartridge Sizes Water Blue & Grey Solvent free Epoxy Pipetank 151 PW A two component surface tolerant solvent free epoxy formulation with fast curing properties. Provides long-term corrosion protection to steel & concrete surfaces in Potable Water immersion conditions & can be applied under water. Used as a repair & make good coating for existing epoxy linings Used as a high quality lining for tanks and pipe, applied directly onto suitably prepared steel Has provided good service in immersion condition for more than 20 yrs Suitable for contact with Potable Water Conforms to SANS 1217 Drinking Water Requirement Kit Size (L) Application Colour Product Type 200 ml, 1 & 4.5 L Kits & Various Cartridge Sizes Water Blue & Grey Solvent free Epoxy Pipetank 151 Rapid A two component surface tolerant solvent free epoxy formulation with fast curing properties that provides long-term corrosion protection to steel & concrete surfaces in immersion conditions & can be applied under water. Fast cures within 2 hours @ 25C at 70% RH Used as a repair & make good coating for existing epoxy linings Used as a high quality lining for tanks and pipe, applied directly onto suitably prepared steel Has provided good service in immersion condition for more than 20 years Kit Size (L) Application Colour Product Type 200 ml, 1 & 4.5 L Kits & Various Cartridge Sizes Water Blue & Grey Solvent free Epoxy Pipetank 152 LV-AS Two component solventless surface tolerant high build epoxy coating formulated to provide long term maintenance free corrosion protection of mild steel and other selected substrates in a single coat by airless spray application. Extremely high levels of adhesion Provides unparalleled combination of proven coating protection properties with extensive limited fre hazard contribution Excellent resistance to abrasion and mechanical damage Can be used against a wide range of chemicals and provides excellent resistance to sea water immersion Kit Size (L) Application Colour Product Type 5 & 18 L Kits 120 ml, 400ml & 1.2L Cartridges Selected RAL Colours Solventless Epoxy Pipetank 162 Hotcoat A two component surface tolerant solvent free epoxy formulation used as a high quality lining for steel & concrete pipes & vessels. Provides long term corrosion protection to steel & concrete in immersion conditions. Can be applied 1000um thick in one application Highly water resistant properties Excellent erosion resistance when conveying slurries High gloss, hard cured surface produces low friction conditions for pipe internals Kit Size (L) Application Colour Product Type 200 ml, 60 & 600 L & Various Cartridge Sizes Water Blue Solvent free Epoxy Pipetank 162 PW Hotcoat A two component surface tolerant solvent free epoxy formulation used as a high quality lining for steel & concrete pipes & vessels. Provides long term corrosion protection to steel & concrete. Can be applied 1000um thick in one application Highly water resistant properties Excellent erosion resistance when conveying slurries High gloss, hard cured surface produces low friction conditions for pipe internals Suitable for contact with Potable Water Conforms to SANS 1217 Drinking Water Requirement Kit Size (L) Application Colour Product Type 200 ml, 60 & 600 L & Various Cartridge Sizes Water Blue Solvent free Epoxy Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 20 Glass Flake Pipetank Flake Glass 1000 Two component solvented high solids epoxy fnish coating containing chemically resistant fake glass ofering excellent corrosion and chemical resistance. Protects steelwork in areas where high abrasion and corrosion resistance are required Used in splash zones in marine conditions such as jetties, decks and bridges Other uses include chemical plants, pulp and paper mills, water treatment plants and mining process plants Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Red Oxide and Grey Glass Filled Epoxy Pipetank Flake Glass Vinyl Ester Two component solvented epoxy vinyl ester resin containing fake glass with a particle size C. This product is designed for the protection of plant and structures in chemical plants, coastal and marine environments. Superior resistance to abrasion and severe mechanical stress, while giving toughness and elongation Superior thermal and corrosion resistance performance properties Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits White Glass Filled Epoxy Vinyl Ester Irathane Glass Flake A range of glass fake flled vinyl ester systems suitable for lining metallic structures containing a wide variety of chemicals and oils. Combined high temperature and chemical resistance Range includes products to match a wide range of cost and performance criteria Based on over 30 years track record of Fugi Resin Co. Ltd, systems are available to counteract a wide variety of problems Kit Size (kg) Application Colour Product Type 5 kg Various Glass Filled Vinyl Ester Solventless Epoxies Pipetank Cureseal A three component water based amine cured epoxy primer/sealer formulated for use as a primer for new or existing concrete or as a concrete curing membrane. Excellent adhesion to green concrete Suitable for use with drinking water Excellent sealer for machine abraded foors Excellent adhesion to substrate & subsequent epoxy coatings SANS 241-1217 Drinking water approval certifed Meets ASTM 309 Requirements for use as a concrete curing compound Kit Size (L) Application Colour Product Type 4 and 20 Litre Pale Blue Amine cured epoxy Water Based Epoxy Primer A two component water-based epoxy primer which provides excellent adhesion to a variety of substrates. Used as an adhesive primer on tiled or gloss surfaces, masonry or metal Used as an insulating coating over bituminous coatings Excellent adhesion to suitably prepared surfaces Excellent adhesive surface for subsequent coatings of emulsion or solvent based paints Used as a primer for solvent free wall coatings, strippable coatings Kit Size (L) Application Colour Product Type 5 and 20 Litre Of White Epoxy Amine Emulsion Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray Protective & Anti-Corrosive Coatings 21 High Temperature Coatings Silicone Acrylic Finishcoat Single component solvented silicone acrylic pigmented fnish formulated for use on suitably primed steelwork in chemical plants and at elevated temperatures. Provides an of gloss fnish with excellent long term durability and resistance Designed for use with surface temperatures from ambient to 200C Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits White Silicone/ Acrylic Silicone Aluminium Hi-Heat Finishcoat Single component solvented, silicone pigmented fnishcoat containing high temperature resistant aluminium. Recommended for fues, stacks, furnaces, boilers, exhausts, jet engines and any other metal part operating at temperatures up to 540C Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Aluminium Silicone Aluminium Silicone Matt Black Hi-Heat Finishcoat Single component solvented, silicone pigmented fnishcoat providing a high temperature resistant matt black. Recommended for fues, stacks, furnaces, boilers, exhausts, jet engines and any other metal part operating at temperatures up to 500C Kit Size (kg) Application Colour Product Type 5 and 20 Litre Kits Matt Black Silicone Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 22 Protective & Anti-Corrosive Coatings High Temperature Coatings Apexior 1 A single component, boiling water/steam immersion coating to 371C. Apexior 1 is extensively and regularly used in a large number of the best know boiler plants here and abroad, and has the unqualifed endorsement of many leading engineers Used for water and steam surface of boiler drums and tubes, steel tubes etc or where the internal surfaces are ordinarily hot and wet Unafected by pressures and high temperatures Kit Size (L) Application Colour Product Type Please Enquire Black Organic Apexior 3 A single component, fresh / salt water immersion coating from -40C to 60C. Formulated for the waterside corrosion prevention of metal surfaces Resistant to continuous immersion in fresh or salt water as well as frequently wet or high humidity environments Kit Size (L) Application Colour Product Type 1 US Gallon (3.78 Litre) Black Organic Thurmalox Coatings A range of high temperature resistant coatings. Coatings temperature resistant up to 700C High quality and proven performance Kit Size (kg) Application Colour Product Type Various Various Various Various Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 23 Protective & Anti-Corrosive Coatings Polyurethane/Urea Irathane 155 A two component solvented elastomeric polyurethane/urea formulated for use in severe abrasion conditions and for resistance to dilute acids and alkalis, sea water and fexural movement. Over 30 Years successful track record in mineral processing and hydroelectric generation Long pot life allows coating of complex components (fans, rotors etc.) and the ability to vary thickness to focus cost efectively on critical areas Bonds to most metals including mild steel, cast iron, stainless steel, titanium, naval bronze etc with the correct selection of Irabond Primers Kit Size (L) Application Colour Product Type 10 Litre 2 Litre (brush) Cream Polyurethane/Urea Irathane 255 A two component solvented trowel applied polyurethane for the severest abrasion applications. Exceptional abrasion resistance Ideal for repairs to PU or rubber components and linings Highly elastomeric, with resistance to dilute acids and alkalis Kit Size (L) Application Colour Product Type 4 Litre and 0.75 Litre Orange Polyurethane/Urea Aqualine 300 300TG 400 - 650 A range of 100% Solids polyurethane/urea systems for lining concrete structures requiring a variety of approvals. Aqualine 300 and 300 Trowel Grade (TG) for lining waste, sea water and other non potable water containing structures Aqualine 400 for lining of potable water structures requiring WRAS listed and other similar level national approvals Aqualine 650 for lining potable water structures requiring Secretary of State (DWI) and a selection of similar level national approvals Kit Size (kg) Application Colour Product Type Various Various Polyurethane/Urea Polyureas Polyurea 2000 A 100% solids fast set elastomeric Polyurea combining resistance to abrasion and many dilute chemicals ideal for large areas where minimal downtime is required. Fast set allows cost efective application to large areas, used for waterproofng potable water structures UK WRAS Listed suitable for use on potable water applications Can be used with Irabond Primes and adhesive to bond to metal substrates as well as its normal use on concrete 1:1 Mixing Ratio Kit Size (L) Application Colour Product Type 5 and 20 Litre Kits Grey Polyurea Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 24 Protective & Anti-Corrosive Coatings MS Primer A two component solvented acrylic polyurethane primer that when combined with a catalyst can be applied to properly prepared substrates as an undercoat for many suitable topcoats. Fills many imperfections on the substrate such as scratches, chips and minor indentations Easily sanded once dry Provides good anti-corrosive properties to protect underlying metal substrates Kit Size (L) Application Colour Product Type 1 and 5 Litre Beige Acrylic Polyurethane Primer Finishprime Polyurethane A two component solvented aliphatic isocyanate cured polyurethane primer/fnish which contains anti-corrosive pigments and can be used as a primer. It contains UV absorbing properties and can be used as a topcoat on itself. Good resistance to UV and atmospheric exposure Good colour and gloss retention, with low chalking and yellowing properties Tough and abrasion resistant Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide and Grey Polyamide Cured Epoxy Finishcoat Polyurethane 2:1 A two component solvented acrylic polyurethane fnish coating. Provides highly durable direct gloss fnish coat incorporating an extensive range of performance enhancing characteristics. Good quality, gloss, coverage and excellent fow Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Acrylic Polyurethane Polyurethanes Finishcoat Polyurethane Polyester 3:1 Kit Size (L) Application Colour Product Type 1, 5 and 200 Litre RAL, NCS and SABS Acrylic Polyurethane A two component solvented Polyester/Polyurethane formulated for use as a top/fnish coat where an exceptional fnish is required. Provides a highly durable direct gloss fnish, cures to a tile like fnish Resistant to UV & sunlight & is Non-yellowing Excellent fexibility & durability & resistance to chalking Unafected by salt water or aggressive industrial environments Good resistance to oils, fats, aqueous solution & most industrial chemicals Finishcoat Polyurethane 4:1 Kit Size (L) Application Colour Product Type 1, 5 and 200 Litre RAL, NCS and SABS Acrylic Polyurethane A two component solvented Polyurethane formulated for use as a top/ fnish coat on suitably prepared surfaces. Provides a highly durable direct gloss fnish Resistant to UV & sunlight & is Non-yellowing Excellent fexibility & durability & resistance to chalking Unafected by salt water or aggressive industrial environments Good resistance to oils, fats, aqueous solution & most industrial chemicals Finishcoat Polyurethane 9:1 A two component solvented aliphatic Polyurethane system suitable for use on a wide range of steel, fbreglass and other substrates where good durability is required such as transformer cabinets, cranes, pumps, and valves, electric motor housings etc. Fast drying & durable, this product is the logical alternative to AD Enamel and far outperforms QD Enamels Exhibits excellent fexibility and durability and is resistant to chalking Excellent adhesion over epoxy primers, good corrosion and chemical resistance Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre RAL, NCS and SABS Acrylic Polyurethane Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 25 Protective & Anti-Corrosive Coatings Protec Range Kit Size (L) Application Colour Product Type 400 L Kit & Various Cartridge Sizes Various Solvent free Polyurethane A range of 100% solids, fast set, fexible, direct to metal polyurethanes with exceptional performance properties for the internal & external protection of pipes with a variety of approval criteria. SANS 1217 Type 1C Protec I Standard performance grade Protec II Higher performance grade Protec II AM contains EPA registered additives for enhanced microbiological growth resistance Protec II PW Certifed per ANSI/NSD standard 61 for use as a lining for Potable Water storage & pipe works Polyurethanes Irathane 2855-80 A 100% solids hot processed polyurethane system specifcally developed for centrigugal lining of slurry pipelines. Excellent chemical and abrasion resistance to most slurries 2:1 ratio quasi-prepolymer system for ease of processing Suitable for casting of abrasion resistant components Kit Size (L) Application Colour Product Type 75 Litre Unpigmented Polyurethane Ura-Shield 5324 A 100% solids fast set, aromatic polyurethane hard-coat for the production of seamless plastic-like protection in food handling environments. Meets ANSI/NSF Standard 51 for Food Equipment Materials Bonds to various substrates including plywood to produce weight savings in application such as trawler holds Kit Size (kg) Application Colour Product Type 10/110 US Gallon 37,85/416.40 Litre White Polyurethane Finishcoat Polyurethane Spatter Structure Kit Size (L) Application Colour Product Type 5 Litre Kit Various Aliphatic Isocyanate Cured Polyurethane A three component solvented aliphatic isocyanate cured polyurethane system suitable for use on a wide range of substrates such as steel, fbreglass and other substrates where a good quality structure fnish is required. The spatter structure enhances the appearance of the fnished item and hides any abnormalities in the surface being coated. Good resistance to UV and atmospheric exposure Good colour and gloss retention, with low chalking and yellowing properties Tough and abrasion resistant Finishcoat Polyurethane WB A two component solventless acrylic polyurethane coating, Provides highly durable direct gloss fnish colour coat incorporating and extensive range of performance characteristics. Zero V.O.C. Economically friendly Exhibits excellent fexibility and durability and is resistant to chalking Excellent adhesion over epoxy primers, good corrosion and chemical resistance Outstanding operational performance including abrasion, chemical and impact resistance and colour/gloss retention Kit Size (L) Application Colour Product Type 1 and 5 Litre RAL, NCS and SABS Solventless Acrylic Polyurethane Pipetank 165 Hotcoat A two component solvent free polyurethane coating consisting of a base polyol component & a highly reactive isocyanate activator, when reacted together form a hard, tough, highly adherent coating used in extreme immersion & buried conditions. SANS 1217 Type 1C Used as a very abrasion resistant coating for backfll, slurry or raw water containing abrasive particles Resistant to Cathodic Disbondment & buried conditions Suitable for water, sewage, raw water, chemically polluted water & mining conditions Resistant to permeability, corrosion, chemicals & abrasion Kit Size (L) Application Colour Product Type 60 & 600 Litre Kits RAL 7004 Signal Grey Solvent free Polyurethane Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 26 Protective & Anti-Corrosive Coatings Geothane 5020 Kit Size (L) Application Colour Product Type 400 Litre Tan Polyurethane A 100% solids fast set elastomeric polyurethane with excellent combined dilute chemical and oil resistance. Excellent diesel resistance Can be applied to concrete or to geotextile to provide a seam free liners for frewater and similar contaminated water containment Fast set time controlled to allow bonding of sections of geotextile to ensure leak free joints 1:1 mixing ratio Polyurethanes Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 27 Protective & Anti-Corrosive Coatings Vinyl HB Intercoat A single pack, solvented, vinyl copolymer pigmented intermediate coat suitable for steel structures, shipbuilding, mechanical and automotive engineering transportation and the protection of buildings in chemical plants, coastal and marine environments. Exhibits good fexibility and durability Resistant to a wide range of chemicals Outstanding adhesion Kit Size (L) Application Colour Product Type 5 and 20 Litre Light Admiralty Grey Vinyl Copolymer Vinyl Enamel Finishcoat A single pack, solvented, vinyl copolymer pigmented enamel fnishcoat suitable for steel structures, shipbuilding, mechanical and automotive engineering transportation and the protection of buildings in chemical plants, coastal and marine environments. Exhibits good fexibility and durability Resistant to a wide range of chemicals Outstanding adhesion Kit Size (L) Application Colour Product Type 5 and 20 Litre SABS, RAL and NCS Vinyl Copolymer Vinyl HB Primer Kit Size (L) Application Colour Product Type 5 and 20 Litre Red Oxide Vinyl Copolymer A single pack, solvented, vinyl copolymer pigmented primer suitable for steel structures, shipbuilding, mechanical and automotive engineering transportation and the protection of buildings in chemical plants, coastal and marine environments. Exhibits good fexibility and durability Resistant to a wide range of chemicals Outstanding adhesion Etch Primer A one component solvented high quality etch primer designed to provide excellent adhesion to steel and other metal surfaces and will protect the surface from corrosion until the full paint system is applied. Fast Drying Suitable as an after blast primer Weld-able when applied in thin coats, weld spatter does not adhere to the surface Excellent corrosion protection. A 25m flm will provide up to three months protection on an inland environment Outstanding adhesion & fexibility Available as ready for use (spraying viscosity) Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Red Oxide, Grey, Black & Olive Green Phenolic / Polyvinyl-butyral Etch Primer LS A one component solvented lower build etch primer designed to provide excellent adhesion to steel and other metal surfaces and will protect the surface from corrosion until the full paint system is applied. Fast Drying Suitable as an after blast primer Weld-able when applied in thin coats, weld spatter does not adhere to the surface Kit Size (L) Application Colour Product Type 5, 20 and 200 Litre Red Oxide, Grey, Black & Olive Green Phenolic / Polyvinyl-butyral Vinyls Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 28 E-Zinc 6580 Primer Two component solvented zinc rich organic based polyamide-epoxy primer for the protection of structural steel in salt and weathering environments for use under a wide range of high performance topcoat systems in corrosive environments. Used in pulp, paper, chemical and petrochemical industries 60% Zinc in Dry Film E-Zinc Primer Kit Size (L) Application Colour Product Type 1.5 and 20 Litre Kits Grey Zinc Rich Epoxy Two component solvented zinc rich organic based epoxy primer providing excellent protection to abrasive blast cleaned steel substrates, for use under a wide range of high performance topcoat systems in corrosive environments. Provides outstanding corrosion resistance at least equal to hot dip galvanizing 90% zinc in dry flm Kit Size (L) Application Colour Product Type 1.5 and 20 Litre Kits Grey Zinc Rich Epoxy I-Zinc Primer A two component solvented coating, based on an ethyl silicate binder incorporates a zinc component which cures to a inorganic, hard corrosion resistant layer which protects the steel in a similar way to galvanizing. An inorganic zinc rich primer provides excellent protection to steel substrates For use under a wide range of high performance topcoat systems in corrosive environments Kit Size (L) Application Colour Product Type 10 Litre Metallic Pink Ethyl silicate / zinc Zinc Coatings Protective & Anti-Corrosive Coatings Sponge Scotchbrite Pad Brushes Rollers Conventional Spray Airless Spray Pour Trowel Squeegee Spray 29 Zincfx A two component solventless, zinc rich organic coating containing >80% metal is applied to clean steel and hot dip galvanized surfaces to form an adherent anti-corrosive coating in excess of 100m thick. Zincfx combines the convenience of squish pack technology with the chemistry of modern solvent free epoxies. Zincfx is approved by the Hot Dip Galvanizers Association of South Africa ZincDek Primer Kit Size (L) Application Colour Product Type 1.5 and 5 Litre Tins Grey Zinc Primer One component solvented air drying metallic zinc pigmented primer, organic based, providing anti-corrosion protection to steel substrates, for use under a wide range of high performance topcoat systems in corrosive environments. Provides galvanic protection and prevents under flm corrosion Greater than 90% Zinc in the dry flm Kit Size (gm) Application Colour Product Type 100 gm Squish Pack Grey Zinc Rich Coating ZincDek Cold Zinc Galvanising Spray An cold zinc galvanising aerosol for use after galvanizing as a touch up paint for damaged galvanized surfaces or as a primer or fnal coat on iron or steel. Forms a fexible, non cracking, non-chipping coat that protects the surfaces even in acidic atmospheres. Contains <95% Purity Zinc Used for the protection of Welds, bridges, fences, wrought Iron, guard rails, gutters, structural steel, exposed ferrous metal, areas damaged after hot dip galvanizing Kit Size (L) Application Colour Product Type 400ml Aerosol Grey Zinc Protective & Anti-Corrosive Coatings Zinc Coatings Testing Equipment 107 Cross Hatch Cutter Provides instant assessment of quality of the bond to the substrate Due to its rugged construction this gauge is ideal for thin, thick or tough coatings on all surfaces Available as a basic or full kit 108 Hydraulic Adhesion Testers An extremely versatile gauge which can be used for many adhesion requirements Tests can be made on fat or curved surfaces 270 Pinhole Detectors This unit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors A high quality, low voltage detector with similar accessories to a high voltage sprak tester Visual & audible alarms Automatic sensitivity calibration & voltage checks 112 Hexagonal Wet Film Combs Hexagonal precision formed stainless steel wet flm combs Long lasting & reusable Supplied in a range of thicknesses measuring up to 3000um (120mils) 224 Digital Surface Profle Gauge 224 provides the latest in surface profle measuring technology Accurate, fast & very user friendly, this gauge is available with or without memory Top model available which includes Bluetooth wireless technology & can store up to 50,000 readings in 999 batches 456 Coating Thickness Gauge Available with built in probe or a separate probe (diferent sized & radius probes available) Memory versions are capable of storing up to 40,000 readings in up to 999 batches Available as ferrous (F), non-ferrous (N) or both Ferrous / non-Ferrous (FNF) Standard & Top Models now come with Bluetooth technology for instant transmission with your PC with no cables Calibration Foils Available 30 Testing Equipment 213 Digital Thermometers The latest in microprocessor technology, superior durability & is designed for reliability & ease of use Rubber bumper seals for impact resistance Extruded aluminium case for superior durability C / F switchable Surface, liquid, magnetic & needle probes sold separately Measure from -50C to 850C 266 DC Holiday Detectors Revolutionises high voltage DC testing of coatings porosity detection making it safer, easier & more reliable than ever before Adjustable voltage & standard specifcation selection Up to 30kV DC versions available Audible & visual alarms are activated when a faw is detected Dual safety switch on handle to avoid accidental switch on 319 Dewpoint Meter An extremely versatile digital Dewpoint Meter for measuring & recording the climate parameters required to ensure good quality coating applications Measure & record climatic parameters including relative humidity, air temperature, surface temperature, dewpoint & the diference between the surface temperature & the dewpoint Hi / Low audible & visual alarms when limits are exceeded Intergated fash light to illuminate the surface being measured 31 Allows assessment of the quantity & size of dust particles on surfaces prepared for coating Dust on blast cleaned surfaces can reduce adhesion leading to premature coating failure & sub-standard coating fnish The kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust Supplied in a carry case for use in the feld to assess the surface cleanliness Testing Equipment 142 ISO 8502-3 Dust Tape Test kit Speccoats Weber Reilly Soluble Salts Test Kit Chlor*Test Accurate measurement with high resolution 0.2% Accuracy Checks the force required to remove a coating from a substrate Alluris Force Gauge Soluble iron salts - Ferrous Chloride and Ferrous Sulphate are found in the bottom of corrosion pits of badly corroded steel These salts are soluble in water & can cause osmotic blistering of coatings applied to steel Soluble salts must therefore be removed prior to coating a surface This test kit identifes the presence of soluble salts on abrasive blast cleaned steel READING THE COLOUR CARD When the indicator is sprayed on freshly abraded steel (minimum to Sa 2 of ISO 8501-1 standard) it will react with the soluble iron salts by turning pink The higher the concentration of soluble salts, the darker the colour This colour card as provided as a guideline to the concentration present A test used for testing for chlorides A very reliable & easy test 32 Application Equipment Increasing a materials temperature lowers its viscosity, an efect that can normally only be achieved by thinning the material with solvent. Material is fed at a constant temperature insuring consistency. Two Component Hot Airless spray equipment For automatic mixing, heating & applying of two component solvented & solventless materials from low to high viscosities PLC controlled with paint agitation & automatic fushing & feed controls For the automatic mixing, dosing, colour change & fushing of two component materials. VRC Mix A solution for 2 component material applications Portable VRC mix is an economic, compact & easy to use unit for all materials including high viscosity materials & high delivery Designed to improve your daily work Ensure correct mixing & makes application much easier Quick colour change Mixing Pressure Pots Piston pumps draw the material out of the container & apply the necessary pressure to push it through hoses or pipes to the spray gun. Pumps are pneumatically operated Piston pumps are classifed by pump ratio & volumetric fow Suitable for low to high viscosity materials In diaphragm pumps, the material is drawn out of the container via a double diaphragm and fed through hoses or pipes with the necessary pressure. Double membrane pumps characterised by material feed with very low pulsation Diaphragm Pumps are categorised into 4 groups Simple diaphragm pumps Double diaphragm pumps Ratio double diaphragm pumps High pressure double diaphragm pumps These accomplish several tasks at once. Feed material by means of compressed air that puts the contents inside the pot under pressure The supply of material from the pot is absolutely free of pulsation Pressure pot acts as a material storage facility Available with automatic agitation Airless Piston Pumps Diaphragm Pumps Hot Spraying 33 Application Equipment 34 Airless Manual & Automatic Spray Guns (up to 530 bar) This process is an airless atomizing paint spray method; a piston pump feeds the spray medium from intake to the nozzle increasing the driving air ration pressure by a factor of the pump ratio. This puts the medium under pressure causing atomization and the ability to apply material without the use of air. Application Accessories Reversible Spray Nozzles Flat Tip Nozzles Nozzle Seals & Holders Paint & Air Hoses Pipe Coating Systems For the easy application of higher solids 2 Component materials, solvented or solventless with many varying mixing ratio capabilities. Speccoats ofers internal/external pipe coating systems Internal coating equipment for non rotating pipes from 100mm to 2.5m ID Airless internal/External spray painting of rotating pipes External airless spray painting with fxed spray ring for pipes moving on conveyor External airless spray painting with oscillating automatic spraying ring for pipes laid on or under the ground Brushes & Rollers Air Atomization Manual Guns Available as Cup Guns or Pressure Feed Guns These guns can be used to spray practically all coating materials Available with a variety of nozzle sizes Available as medium pressure or HVLP versions to guarantee the correct transfer efciency Application Equipment 35 HSS Air Gun For the easy application of higher solids 2 Component materials, solvented or solventless with many varying mixing ratio capabilities. Based on a reliable design with proven dependability & service Equipped with unique feature for separate material fow & air atomizing spray control Material is mixed through a static mixer Flow restrictors are available for materials of a low viscosity Non drip, right angle & standard spray nozzles available for getting into hard-to-reach places Cartridge Application HSS Quad 3000 For the easy application of higher solids 2 Component materials, solvented or solventless with many varying mixing ratio capabilities. Up to 3000ml of capacity, the HSS Quad 3000 is perfect for larger volume, plural component spray, foam & meter mix dispense applications Provides increased feld productivity, enhanced fexibility, dispense control & cuts down operator fatigue User friendly features include a large wheelbase, accurate air & material fow, dump & bleed valves & easy cartridge change out procedures All colour coded for easy use Paint Manufacturers Address: 9 Covora Street Jet Park Boksburg Gauteng South Africa International Tel: 00 27 11 397 2140 Within South Africa Tel: 0861 37 2468 International Fax: 00 27 11 397 3420 Within South Africa Fax: 011 397 3420