Professional Documents
Culture Documents
Send completed registration card to us, or register at www.sport-tool.com, to go in the draw to receive a special gift from Navman. A300 Your registration will enable us to optimize our service to you.
Product purchased
M300 S300 R300
W300
X300
Expected use
I expect to use the Sport.Tool approx
User prole
Age: yrs male female
Please tick here to receive offers and product information from Navman.
NAVMAN
X300 Settings
Setting options
Press and hold
to enter setup Press repeatedly to step through the setting options. ) to start or stop editing Press both buttons together ( a setting option.
repeatedly to step through selectable states, or While editing, press or increase/decrease values. Press and hold the appropriate button to increase/decrease values quickly.
Set (12hr) lets you set 12hr or 24hr time format Set (31-12) lets you set dd-mm or mm-dd date format Calc up When calc up is ON the X300 calculates data for all movement (uphill and downhill). When calc up is OFF the X300 calculates information for downhill movement only. Beep When beep is ON a beep will sound when the buttons are pushed. Set units (km/h) lets you set speed units to km/h or mph
Distance and altitude are displayed in units corresponding to the speed units, i.e. if you choose km/h for speed units, then distance is displayed in km and altitude in m.
Set offset lets you adjust the X300 to display local time
The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time.
to leave setup
X300
NAVMAN
X300 Settings
edit
set (12hr)
set (12hr)
set 12hr
set 24hr
accept
set (31-12)
edit
set (31-12)
set 31-12
set 12-31
accept
Calc up
edit
Calc up
accept
beep
edit
beep
accept
edit
set offset
edit accept
time (date)
KEY = press this button = press this button = press both buttons together
X300
Downloaded from www.Manualslib.com manuals search engine
NAVMAN
X300 Modes
Press repeatedly to step through the modes (hold cycle automatically through modes).
Speed shows session distance and current speed Speed (AVG) shows session distance and average speed Speed (MAX) shows session distance and maximum speed Odometer shows total distance from last odometer reset Altitude shows total accumulated altitude and current altitude Zone OFF lets you skip the zone setting options Zone alerts do not sound if zone status is OFF. Zone ON makes the min and max zone setting options available If zone status is ON, alerts sound when zone limits are passed. Zone MIN lets you set your minimum target speed Zone MAX lets you set your maximum target speed Clock shows the current time and date
(You may need to adjust the settings to display your local time.)
Timer Recall lets you recall stored lap data. Repeatedly pressing recalls lap data starting from the last stored lap, then lap 1, 2, 3 etc.
Press and hold
to shut down the X300
X300
Downloaded from www.Manualslib.com manuals search engine
NAVMAN
X300 Modes
operating details store current lap data clear all session data*
store current lap data clear all session data* store current lap data clear max speed only store current lap data clear odometer only store current lap data clear accumulated altitude only
accept
AVG
Speed (AVG)
MAX
Speed (MAX)
2 873
Odometer
Altitude
edit
ZONE SET
Zone OFF
Zone OFF
Zone ON
edit
accept
edit
Zone MIN
Zone MIN
accept
edit
Zone MAX
Zone MAX
Clock
Timer
store current lap data clear all session data* store current lap data clear all session data*
RCL
Timer recall
recall lap data restart recall from lap 1 (*does not clear odometer)
KEY = press this button = press this button = press both buttons together = press and hold both buttons together
X300
Downloaded from www.Manualslib.com manuals search engine
X300
QUICK START GUIDE
X300
Downloaded from www.Manualslib.com manuals search engine
Step 1
Get ready
Fit the battery
1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure. 2. Insert battery with end as indicated inside enclosure. 3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal.
Fit the X300 The X300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to tting.
L
Be outdoors The X300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the X300 outdoors with an unobstructed view of the sky.
X300
Downloaded from www.Manualslib.com manuals search engine
Step 2
Get set
Know the buttons
The control buttons, and (as shown above) are pressed separately or together to turn the unit ON and OFF, cycle through modes, and select mode options.
Know the startup options 1. enter setup 2. start normal operation
Always enter setup rst if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the X300.
Flashing icon = seeking GPS signals Constant icon = GPS signals obtained
Startup could take up to 80 seconds to get all satellite data.
If you release before the counter reaches zero, the X300 will immediately start normal operation.
For details about system settings see over page or consult User Guide.
to leave setup
counter
After leaving setup, the X300 automatically starts normal operation displaying the speed mode rst.
X300
Downloaded from www.Manualslib.com manuals search engine
Step 3
Go
Start normal operation Press
to start normal operation
When starting directly into normal operation X300 will start in the mode it was in at last shutdown. The X300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order:
AVG MAX
8 7
2 3
Speed
Timer RCL
RCL
Odometer
Altitude
Zone OFF Zone ON Zone MIN
ZONE SET
Zone MAX
For details about modes or setting zone limits, see over page or consult User Guide.
current speed
km/h
Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also store laps or clear session data. While in Speed mode Press to store lap data Press and hold to clear all* session data Press to go to next mode
(*Does not clear odometer)
When you want to shut down the X300 Press and hold
Now you know.
X300
Downloaded from www.Manualslib.com manuals search engine
LA000550B
2005 Navman NZ Ltd. All rights reserved. "Sport.Tool" and "Now you know" are trademarks of Navman NZ Ltd.
Navman Europe Customer Registration 4G Gatwick House Peeks Brook Lane, Horley Surrey, RH6 9ST United Kingdom
sporttool
sporttool
sporttool