Professional Documents
Culture Documents
Foreword
This Annex has been made out based on the scope, references, chemical composition, mechanical
properties, sampling and mechanical property tests specified in ISO 3574!"#$ %&oldreduced carbon steel
sheet of commercial and dra'ing (ualities) 'hich corresponds to the text of this Standard*
It is not allo'ed to apply only a part of this Annex instead of the re(uirements specified in the text*
1. Scope and field of application
!*! This Annex applies to coldreduced carbon steel sheet of commercial and dra'ing (ualities* It is suitable
for applications 'here surface is of prime importance*
!*+ &ommercial (uality sheet %&,I)is intended for general fabricating purposes 'here sheet is used in the flat
or for bending, moderated forming, and 'elding operations* It is produced in thic-ness of .*3$ mm and
thic-er %commonly produced up to 4 mm) and in 'idths of $.. mm and o/er, in coils and cut lengths*
!*3 0ra'ing (uality sheet %&,+, &,3, &,4) is intended for dra'ing or se/ere forming, including 'elding* It is
produced in thic-nesses of .*3$ mm and thic-er %commonly produced up to 4 mm) and in 'idths of $.. mm
and 'ider, in coils and cut lengths*
Drawing qualities are identified as follows:
&,+ dra'ing (uality
&,3 deep dra'ing (uality
&,4 deep dra'ing (uality special -illed %nonaging)
!*4 &oldreduced sheet less than $.. mm 'ide may be slit from 'ide sheet and 'ill be considered as sheet*
. !eferences
ISO !.+4
1etallic materials 2ardness test ,oc-'ell superficial test %scales !5 3, 3.
3, 45 3, !5 T, 3. T and 45 T)
ISO $5.7! 1etallic materials 2ardness test 4ic-ers test 5art ! 6 245 TO 24!..
ISO $5.#
1etallic materials 2ardness test ,oc-'ell test %scales A7&089:2
;)
ISO $#"+ 1etallic materials Tensile testing
[ CLOSE ]
"nformati#e reference
"ntroduction
This Informati/e reference gi/es the supplement to the chemical composition and mechanical properties, and
matters to be attended at the time of contract, but does not form part of this Standard*
1. Chemical composition
The chemical composition %cast analysis /alues shall be as gi/en in Informati/e reference Table !*
"nformati#e reference $able 1. Chemical composition
<nit 6 =
Symbol of (uality & 1n 5 S
S5&& .*!+ max* .*.5 max* .*.4. max* .*.45 max*
S5&0 .*!. max* .*45 max* .*.35 max* .*.35 max*
S5&8 .*.# max* .*4. max* .*.3. max* .*.3. max*
!emar%s 6
9or the steel sheet and coil of grades !>#hard, !>4 hard, !>+ hard and full hard, increment of hardness is
achie/ed sometimes by changing their chemical composition instead of by temper rolling*
. &echanical properties
+*! The combination of the symbol of (uality, temper grade and surface finish, and items of mechanical
properties to be applied shall be as gi/en in Informati/e reference Table +*
Informati/e reference Tabel +* Applicable items of mechanical properties
Symbol
of (uality
Temper grade
0iscrimination of
surface finish
Symbol
Tensile
test
/alue
3onaging
property
7ending2ardness
S5&& Asannealed S5&&A O
Asannealed%'hen
specified to guarantee
mechanical properties)
S5&&T
A
O O
0ull finish
S5&&
S0
7right finish
S5&&
S7
Standard temper
grade%'hen specified to
0ull finish
S5&&T
S0
[ COLSE ]
"nformati#e reference
"ntroduction
This Informati/e reference gi/es the supplement to the chemical composition and mechanical properties, and
matters to be attended at the time of contract, but does not form part of this Standard*
1. Chemical composition
The chemical composition %cast analysis /alues shall be as gi/en in Informati/e reference Table !*
"nformati#e reference $able 1. Chemical composition
<nit 6 =
Symbol of (uality & 1n 5 S
S5&& .*!+ max* .*.5 max* .*.4. max* .*.45 max*
S5&0 .*!. max* .*45 max* .*.35 max* .*.35 max*
S5&8 .*.# max* .*4. max* .*.3. max* .*.3. max*
!emar%s 6
9or the steel sheet and coil of grades !>#hard, !>4 hard, !>+ hard and full hard, increment of hardness is
achie/ed sometimes by changing their chemical composition instead of by temper rolling*
. &echanical properties
+*! The combination of the symbol of (uality, temper grade and surface finish, and items of mechanical
properties to be applied shall be as gi/en in Informati/e reference Table +*
Informati/e reference Tabel +* Applicable items of mechanical properties
Symbol
of (uality
Temper grade
0iscrimination of
surface finish
Symbol
Tensile
test
/alue
3onaging
property
7ending2ardness
S5&& Asannealed S5&&A O
Asannealed%'hen
specified to guarantee
mechanical properties)
S5&&T
A
O O
0ull finish
S5&&
S0
7right finish
S5&&
S7
Standard temper
grade%'hen specified to
0ull finish
S5&&T
S0
'. Dimensional tolerances
$*! 5osition of measurement on dimensions
The position of measurement on dimensions shall be as follo's6
%!) 9or the steel sheet and regular portion of the steel coll, measurement on thic-ness shall be made at any
point not less than !5 mm apart from both side adges* In the case 'here the 'idth is less than 3. mm,
ho'e/er, the measurement shall be made at a mid'idth position*
%+) 1easurement on 'idth shall be made at regular portion for the steel coil and at any place for the steel
sheet*
%3) 1easurement on length shall be made at any place for the steel sheet*
$*+ Thic-ness tolerances
The thic-ness tolerances shall be as follo's6
%!) The thic-ness tolerances shall be applied to the nominal thic-ness*
%+) The thic-ness tolerances shall be classified into classes A and 7 as gi/en in Table # and Table ",
respecti/ely*
$able (. $hic%ness tolerances) class A
<nit 6 mm
0iscrimination according to
nominal thic-ness
0iscrimination according to nominal 'idth
<nder $3.
$3. or o/er
to and excl*
!...
!... or o/er
to and excl*
!+5.
!+5. or o/er
to and
excl*!$..
!$.. or o/er
<nder .*+5 ?@ .*.3 ?@ .*.3 ?@ .*.3
.*+5 or o/er to and excl* .*4. ?@ .*.4 ?@ .*.4 ?@ .*.4
.*4. or o/er to and excl* .*$. ?@ .*.5 ?@ .*.5 ?@ .*.5 ?@ .*.$
.*.$ or o/er to and excl* .*#. ?@ .*.$ ?@ .*.$ ?@ .*.$ ?@ .*.$ ?@ .*.7
.*#. or o/er to and excl* !*.. ?@ .*.$ ?@ .*.$ ?@ .*.7 ?@ .*.# ?@ .*."
!*.. or o/er to and excl* !*+5 ?@ .*.7 ?@ .*.7 ?@ .*.# ?@ .*." ?@ .*!!
!*+5 or o/er to and excl* !*$. ?@ .*.# ?@ .*." ?@ .*!. ?@ .*!! ?@ .*!3
!*$. or o/er to and excl* +*.. ?@ .*!. ?@ .*!! ?@ .*!+ ?@ .*!3 ?@ .*!5
+*.. or o/er to and excl* +*5. ?@ .*!+ ?@ .*!3 ?@ .*!4 ?@ .*!5 ?@ .*!7
$able (. *continued+