GPRS Module is based on the SIM900 Quad-band 850 / 900 / 1800 / 1900MHz GPRS multi-slot calss 10 / 8 GPRS mobile station class B Compliant to GSM phase 2 / 2+ class 4 (2W@850/900MHz) class 1 (1W@1800/ 1900MHz) It is controlled via AT Commands (GSM 07.07, 07.05 and SIMCOM enhanced at Commands), and fully compatible with Arduino / It
GPRS Module is based on the SIM900 Quad-band 850 / 900 / 1800 / 1900MHz GPRS multi-slot calss 10 / 8 GPRS mobile station class B Compliant to GSM phase 2 / 2+ class 4 (2W@850/900MHz) class 1 (1W@1800/ 1900MHz) It is controlled via AT Commands (GSM 07.07, 07.05 and SIMCOM enhanced at Commands), and fully compatible with Arduino / It
GPRS Module is based on the SIM900 Quad-band 850 / 900 / 1800 / 1900MHz GPRS multi-slot calss 10 / 8 GPRS mobile station class B Compliant to GSM phase 2 / 2+ class 4 (2W@850/900MHz) class 1 (1W@1800/ 1900MHz) It is controlled via AT Commands (GSM 07.07, 07.05 and SIMCOM enhanced at Commands), and fully compatible with Arduino / It
GPRS module is a GSM/GPRS module based on the SIM900 Quad-band GSM/GPRS module. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Arduino / Iteaduino and Mega.
Features
Quad-Band 850/900/1800/1900MHz GPRS multi-slot calss 10/8 GPRS mobile station class B Compliant to GSM phase 2/2+ Class 4 (2W@850/900MHz) Class 1 (1W@1800/1900MHz) Control via commands (GSM 07.07, 07.05 and SIMCOM enhanced AT Commands) Short message service Free serial port selection 3.5 inch standard sonic sockets for MIC and phone Operation temperature: -40 ~ +85 2 Tech Support: support@iteadstudio.com GPRS Module iteadstudio.com 2011-12-06
Specifications
PCB size 71.4mm X 66.0mm X 1.6mm Indicators PWR, status LED, net LED Power supply 5V Communication Protocol UART RoSH Yes
Electrical Characteristics
Specification Min Type Max Unit Power Voltage(Vsupply) 4.5 - 5.5 VDC Input Voltage VH: 0.7VCC - 5.5 V Input Voltage VL: -0.3 0 0.3VCC V Current Consumption(pulse) - - 2000 mA Current Consumption(Continues) 500 mA Baud rate 115200 bps 3 Tech Support: support@iteadstudio.com GPRS Module iteadstudio.com 2011-12-06
Hardware
Figure 1 Top Map Interface Pin Description Rst 1 Reset the SIM900 module P 2 Power switch pin of SIM900 module Tx 3 UART data output Rx 4 UART data in DT 5 Debug UART data output DR 6 Debug UART data input - 7 GND + 8 VCC 4 Tech Support: support@iteadstudio.com GPRS Module iteadstudio.com 2011-12-06
Installation
Power on GPRS module
User can power on the GPRS module by pulling down the PWR button or the P pin of control interface for at least 1 second and release. This pin is already pulled up to 3V in the module internal, so external pull up is not necessary. When power on procedure is completed, GPRS module will send following URC to indicate that the module is ready to operate at fixed baud rate.
Indicator LED and Buttons:
NETSTATUS: The status of the NETSTATUS LED is listed in following table:
Status Description Off SIM900 is not running 64ms On/800ms Off
SIM900 not registered the network 64ms On/3000ms Off
SIM900 registered to the network 64ms On/300ms Off
GPRS communication is established STATUS: Power status of SIM900. PWR: Power status of GPRS module.
PWR: After the GPRS module power on, you need to press the POWER button for a moment to power on the SIM900 module. RESET: Reset the SIM900 module.
Revision History
Rev. Description Release date v1.0 Initial version 2011-12-06