TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR
SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA ,
BUKIT JALIL PAGE 1 PROVISION OF SUPPLY, DELIVER, INSTALL, OBTAIN NECESSARY APPROVAL FOR THE TESTING AND COMMISSIONING OF 1 (ONE) UNIT 1500 KVA CANOPY TYPE STANDBY DIESEL GENERATOR AND 1 (ONE) UNIT OF 1300 KVA FOR THE MIMOS WAFER FABRICATION 2 1.0 GENERAL TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 2 1.01 DESCRIPTION Manufacture, test at work, deliver to site, install, testing at site and commission a complete Standby Canopy type Diesel Generator set in accordance with a Contract Document. Capacity ! " !.#M$% for MS&! and MS&!& '(acilities support e)uipment* ! " !.+M$% for MS&, '-roduction e)uipment* 1.02 EXTENT OF WORK !..,.! /orks shall include but not limited to the followings '!* Diesel engine. ',* %lternator. '+* %ir intake silencer. '0* %ir discharge silencer. '#* 1adiator. '2* 3nsulation. '4* %M( &oard. '5* -ower cables '6* Control cables. '!.* %coustic system. '!!* Service tank !.,., -reparation of proper concrete plinth 27 above the ground level, where the generator set will be placed. !.,.+ &ack8up diesel tank, complete with auto pumping system. 9ank capacity ,0 hours storage based on the , gen sets running at full load. . Materials Compatible with the diesel fuel. :evel sensor, and opening for provision to provide a automatic sensor to &%S 'by other* !.,.+ 9o carry out necessary electrical wiring from the %M( board to the :9 ;MS& and to perform <oint testing and commissioning of the total system. !.,.0 /arranty and maintenance for ,0 months after the final acceptance of the system. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 3 !.,.# =n the <ob training to the M3M=S>s appointed maintenance team. !. people
2.0 PRODUCTS 2.01 LIST OF ACCEPTABLE MANUFACTURERS 2.01.1 DIESEL ENGINE Caterpillar, ?ohler, Cummin, (G /ilson 2.01.2 ALTERNATOR :eroy Somer, Mitsibushi, @ewage Stamford, Mecc%lte, Marathon 2.01.3 ACOUSTIC SYSTEM -owermech, 3sti), %lfa %kustik, Semangat Ma<u or %pproved e)uivalent. 2.02 STANDBY GENERATOR 2.02.1 Genera 9he standby generator set shall be diesel engine driven and mounted on a Mild Steel commons skid base frame of rigid construction. 9he generating set shall have a continuously rated output at site of not less than that specified on the drawings. 9he generating set shall be installed for fully automatic operation during power failures and shall be ready to deliver rated capacity within !. seconds after main failure. 2.02.2 ATMOSP!ERIC CONDITIONS 9he diesel generator set shall suitable for operation under the following ambient conditions8 '!* 9emperature 8 from !2 deg C '2. deg (* to 0. deg C ',* Aumidity 8 from Bero to !..C within the range of temperature above '+* %tmospheric 8 42. mm of mercury -ressure 2.02.3 ENGINE TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 4 9he engine shall be of the vertical in8line or vee8form, monobloc, four stroke, naturally aspirated or pressure charged, water cooled, direct in<ection, compression ignition type, capable of cold starting and complying with 3S=+.028! and 3S=5#,5. 9he engine should be four strokes with an engine speed of !#.. 1-M. 9he engine shall be capable of delivering not less than the power re)uired by the full load rating of generator after derating due to ambient conditions above, and after deducting the power take8off for engine driven au"iliaries including lubricating oil pump, circulating water pump if applicable, radiator or cooling air fan e"citer. % power calculation verifying the above, together with power curve, efficiencies chart, shall be submitted for approval. 9he engine generating set shall be capable of an overload of !.C for one hour in any period of !, hours continuous running. 9he engine shall be supplied complete with lubricating oil pump and circulating water pump, full flow lubricating oil filters, fuel oil filters, lubricating oil pressure gauge, tachometers, integrating hours run recorder, air inlet filter. 9he engine shall be e)uipped with an Dlectronic Governor with hand operated fine speed control. DMS fuel system with 3S=5#,58,, Class G+ governing is preferred. =verspeed trip and low oil pressure shutdown, ,0 volts D.C. starting motor, flywheel with coupling bolts for flange and direct 8 coupled mounting, and all necessary au"iliaries. 9he engine shall be suitable for running on Grade E%E oil engine fuel 'FdistillateF* generally complying with &.S. ,526. 9he engine cooling tower radiator shall be mounted upon the under8frame, together with all necessary au"iliaries, so that completely FpackagedF unit is formed. 2.02." ALTERNATOR 9he alternator shall be directly coupled to diesel engine through bolted flanges, and of drip proof, screen protected, revolving field, salient pole with damper windings, Class D insulation to &.S. ,4#4, brushless and self regulating type and continuously site rated to comply with engine &A- according to &.S. ,2!+. 9he generator shall be mounted on a fabricated steel under8frame by means of oil resistant mountings of the shear compression type so that the entire unit can be bolted to a solid concrete floor without transmitting vibration to ad<acent apparatus or to any part of the building. %ll electrical terminations shall be made with spring washer to ensure good and reliable contact. @eutral point of the alternator shall be solidly earthed. Dlectric heater where necessary shall be provided in the alternator stator to prevent condensation. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 5 9he performance re)uirements of the alternator shall be as follows8 Steady8State Capacity and -erformance 1e)uirement a* %lternator rating %s specified in drawings b* @ame plate k$% %s specified in drawings c* -ower factor ..5 d* @ominal fre)uency at rated k/ #. AB Manually ad<ustable from 02 to #0 AB e* Synchronous operated speed !#.. rpm f* :ine to line voltage at rated output 0!#$ Manually ad<ustable G#C g* -ower Distribution @o. of -hases + @o. of /ires 0 -hase arrangement 18H8& h* $oltage transient performance re)uirements $oltage Dip not to e"ceed !.C $oltage 1ise not to e"ceed ,.C 1ecovery time not to e"ceed ..# seconds 9he generator set shall achieve the above specified performance under the specified ambient conditions. 2.02.# STARTING SYSTEM 9he electric starting system shall be provided complete with engine mounted motor and starting contactor, ,0 volts heavy duty nickel cadmium battery of ample rating for seven successive starts of !# seconds with rest interval of !. seconds or attempts to start without re8charging, and all necessary wiring between these components. /iring shall be carried out using neoprene8insulated conductors in plastic conduit. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 6 % battery charger with dual charging rate 'trickle and booster*, load test switch, ammeter and voltmeter, shall be provided in a sheet steel cabinet properly ventilated. 9he boost charge shall restore the batteries from flat condition at full charge within ,0 hours. Dual smoothed full8wave rectifiers operating in parallel shallbe provided as standby and shall be able to take over supply of the engine starting current in the event of battery failure or battery maintenance. Suitable tappings are to be provided for ad<ustment to suit particular characteristic and to compensate for ageing of the rectifier. 9he e)uipment shall be complete with centre Bero M.C.S.C ammeter and voltmeter, IMains =n> switch and indicator, load test switch and suitably rated test load and boost;trickle;off switch. % bettery charger failure protection unit shall be fitted in each charger unit and arranged to operate in the event of the battery voltage falling below normal float level for a period of more than +. minutes. 2.02.$ COOLING SYSTEM 9he engine shall be water cooled or provided with an integral fan8operated radiator or alternatively shall be air cooled. 9he radiator or cooling air fan, as applicable shall be connected by mean of fle"ible canvas section and steel ducting to the aluminium gravity louvered air outlet set in the wall. Dngines of above #. ?$% should be water cooled. 3f an air8cooled diesel engine is provided, suitable sheet steel ductwork shall be provided to ensure that cooling air is drawn through the cooling fins on the engine to the induced draught fan. 1adiator shall be provided for lubricating oil cooling. 2.02.% EX!AUST SYSTEM D"haust piping of sheet steel construction together with an efficient silencer of the absorption type shall be provided and installed. 9he pipework and silencer shall be properly supported to relieve the engine of all weight. %ll e"posed pipework shall be painted with heat8resistant paint, and all e"haust pipeworks shall be insulated. D"haust pipework passing through the wall of the engine room shall be sleeved, the outer pipe being provided with a split circular flange properly fi"ed to each side of the wall, the sleeve being packed internally with asbestos rope and grounded to the wall. % moisture drain trap with drain cock shall be fitted at the lowest point. % fle"ible <oint of approved type shall be provided at the connection to <oin the engine. D"haust ductwork connecting radiator to the discharge outlet shall be provided. 9he ductwork shall be manufactured from ,. gauge G.3. sheets and e"haust duct silencers provided. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 7 9he design and construction of the e"haust system shall take into consideration the permissible engineEs e"haust back8pressure and the noise pollution permitted. 2.02.& FUEL SYSTEM 9he generating set shall be provided complete with a day service fuel tank which must be so located to permit gravity feed to the engine pumps. 3t may be arranged on the combined under8frame, or alternatively bracket mounted upon the wall ad<acent to the generator. 9he capacity of day service fuel tank shall be ,... litres. 9he fuel tank shall be fabricated from mild steel sheet construction, and hot dip galvanised, painted inside and outside with oil8resistant primer and e"ternally finished with undercoat and topcoat. % calibrated contents gauge shall be fitted. % semi8rotary hand8operated pump shall be provided and installed for filling the fuel tank, with a suitable length of oil8resistant hose for off8loading fuel oil from drums. %lternative arrangements may be provided but shall be sub<ect to the approval of the Dngineer. $ent cap overflow connection, drain valve and piping, drip tray and fuel level indicator should be provided. 2.02.' ANTI()IBRATION MOUNTINGS 9he whole generator set shall be provided with anti8vibration mounting arrangement giving a minimum isolation efficiency of 6#C. Spring type anti8vibration mountings shall be fitted with leveling and ad<ustment. 2.02.10 AUTO MAINS FAILURE *AMF+ AND GENERATOR CONTROL BOARD 9he above may be a common panel fabricated from !0 S/G floor standing cubicle type and installed complete with all necessary e)uipment for engine and alternator protection and control. 2.02.10.1 MCCB % moulded case circuit breaker 'MCC&* of the appropriated rating and breaking capacity shall be provided for ad<ustable overload and short circuit protection of the generator. 9he MCC& shall have a shunt trip coil and a lockable type operating handle. 3DM9 type earth fault relay shall also be provided. 2.02.10.2 In,-r./en-, 9he instruments to be provided shall include ammeter with selector switch, voltmeter with selector switch, fre)uency meter, power factor meter, kilowatt8hour meter, kilowatt meter, hour run meter, attempt8start counter with manual reset. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 2.02.10.3 Rea0, 1 E/er2en30 B.--4n -hase failure relay, necessary control relays, timers, reset buttons, visual and audible alarms shall also be provided. Mushroom type emergency stop button shall also be provided. 2.02.10." Ba--er0 C5ar2er &attery charger as specified herein before may be housed within the board and the batteries shall be of nickel cadmium type. 2.02.10.# M46e 47 O8era-94n 9he various modes of operation of the generator shall be as follows8 F=((F Generator remains idle indefinitely FM%@J%:F Generator shall be started and shutdown manually by effecting the S9%19;S9=- push buttons. F9DS9F '!* /ithout Changeover Generator shall start automatically after a time delay 'ad<ustable between ! K +. seconds*, and remain operating for a period between #82. minutes, after which the generator shall shut down automatically. Changeover contactor shall not operate. ',* /ith Changeover %utomatic starting and shut down of generator shall be same as of 'a* above e"cept that changeover contactor shall operate during the test period. F%J9=F Generator shall start automatically upon failure of normal supply 'detected by phase failure relay, pick8up and drop out voltage ad<ustable between 5.C 8 !!.C of rated voltage* after a time delay 'ad<ustable between . to +. seconds* Changeover contactor shall operate after alternator has built up to rated voltage. Jpon restoration of normal supply, and if normal supply voltage remains stable between . to +. minutes changeover contactor shall operate to transfer load back to normal supply. Generator set shall, however, continue to operate between . to +. minutes after which it shall automatically shut8 down. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE ! Should during the said period, the normal supply fail again after the initial restoration, the changeover contactor shall immediately operate and transfer the load to the generator set. 2.02.10.$ Aar/, 9he following alarms shall be incorporated !* :ow :ube =il -ressure Dngine shut8down with visual K audible alarms ,* Aigh Lacket /ater 9emperature Dngine shut8down with visual K audible alarms +* Dngine =verspeed Dngine shut8down with visual K audible alarms 0* %lternator =utput $isual and audible alarm #* Dngine (ail to Start Starting circuit locked out '%fter + attempts* with visual and audible alarms 2* :ow (uel :evel in Day 9ank $isual and audible alarms 2.02.10.% In693a-9n2 La/8, 3ndicating lamps shall be provided to8 '!* 3ndicate status of normal 9@& Supply ',* 3ndicate status of changeover contactors '+* /arn that selector switch is not set in F%J9=F position '0* /arn that emergency stop button is in F=((F position '#* /arn that main MCC& is in F=((F or F913-F position 2.03 TOOLS 9ools necessary for normal maintenance by user shall be provided. 2.0" SPARE PARTS LISTS TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 1" % comprehensive spare parts list shall be provided to ensure accurate and easy ordering of parts. 3.0 EXECUTION 3.01 WORK TESTS 9est shall be carried out at the manufacturerEs work in the presence of the Dngineer or his representative and three '+* sets of certificate record of test results shall be provided. 9he following loads and period of running shall be included in the test8 '!* ,#C =ne Aour ',* #.C =ne Aour '+* 4#C =ne Aour '0* !..C (our Aour '#* !!.C =ne Aour Current, voltage, fre)uency, r.p.m. k/ output, radiator water temperature and radiator discharge air temperature, fuel consumptions, oil temperatures and pressure, transient voltage, radiator fan static and e"haust gas temperature shall be recorded and verified. 3.02 SITE TESTS =n completion of installation on site, various tests including se)uential tests on starting, running and safety tests on tripping shall be carried out and witnessed thereof to ensure compliance. %dditional test shall be carried out to measure the noise levels. 3.03 PAINTING 1 FINIS!ES 9hese shall be carried out to the satisfaction of the Dngineer. 3.0" OPERATIONS AND MAINTENANCE MANUALS 9hree '+* sets of installation, operating and maintenance manuals together with spare parts lists, and properly bound with hard cardboard covers shall be provided. 3n addition, three '+* sets of as8fitted drawings depicting the complete installation shall be provided. 3.0# DANGER SIGNS AND FIRST AID C!ART 9he following item shall be provided8 TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 11 '!* %ppropriate danger signs on switchboards and on entry doors to the generator switchroom. ',* =ne framed copy of the F(irst %ir ChartF for treating electrical shocks '+* =ne '!* @o. rubber mat !+mm thick to be laid along the whole length of the %M(;Generator Switchboard. '0* (ramed up drawing of the generator control and schematic drawing. 3.0$ EART!ING %ll non8current carrying metal parts shall be bonded effectively to earth. %n independent earthing system ade)uate for the proposed installation shall be provided. 9he overall resistance of the earthing system shall be less than # ohm. %n earth name plate shall be provided at the main earthing bar stating the date and value of earth resistance obtained. Darth electrodes shall be provided with a concrete inspection chamber installed flush with the surface. 9he neutral of the generator set shall be separately earthed. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 12 3.0% AUT!ORITIES: RE;UIREMENTS 9he test results, certifications and everything else re)uired for seeking approval for the registration of the proposed generator set with relevant authorities shall be provided. 9he said authorities shall include8 '!* Suruhan<aya 9enaga K gas Malaysia ',* Labatan &omba dan -enyelamat Malaysia '+* Labatan ?esihatan dan ?eselamatan -eker<aan '0* ?ementerian Sains 9eknologi K %lam Sekitar '#* 9enaga @asional &erhad 3.0& NOISE CONTROL 9he completed installation shall meet the re)uirements regarding acceptable noise level as set out by ?ementerian Sains, 9eknologi K %lam Sekitar. 9he necessary acoustic treatment and additional measures re)uired to reduce to acceptable level of noise and vibrations generated during running of the proposed generator set are deemed to be inclusive in the Scope of /ork. Such acoustic treatments and measures shall include provisions of noise absorbing wall paneling, noise attenuators on the engine e"haust system and radiator air ducting system, specially constructed noise attenuation bo"es complete with grills;louvers at all openings of the generator room, additional treatment on all doors and door frames leading into generator room and suitably selected spring type vibration isolators. ".0 FACTORY ACCEPTANCE TEST 9he Contractor is to include the price for to and pro passages for factory acceptane test at places of manufacturer for at least five '#* personnel of Cliect;Consultant inclusive of all e"penses related to the acceptance test. TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 13 SC!EDULE OF TEC!NICAL DATA =J9D==1 C%@=-H 9H-D S9%@D&H GD@D1%9=1 SD9 SD1$3CDS 9he 9enderer shall submit on separate sheets following details of the set supplied. -ls state your offer 'Mandatory* !. =verall weight of complete set 'kg* MMMMMMMMMMMM ,. =verall dimensions of complete set %s follows a* :ength 'mm* MMMMMMMMMMMM b* /idth 'mm* MMMMMMMMMMMM c* Aeight 'mm* MMMMMMMMMMMM +. Coupling arrangement between Dngine and %lternator MMMMMMMMMMMM 0. 9ype of mounting used for Dngine and %lternator MMMMMMMMMMMM #. DD9%3:S =( D3DSD: D@G3@D %S (=::=/S a* Manufacturer MMMMMMMMMMMM b* Model or type @o. MMMMMMMMMMMM c* @o. of cylinders MMMMMMMMMMMM d* &ore 'inches* MMMM. Stroke 'inches* MMMMMMMMMMM.... e* 9otal swept volume 'cu.ins* MMMMMMMMMMMM f* Compression ratio MMMMMMMMMMM.... g* 1ated A.-. of engine MMMMMMMMMM.M... h* Speed of engine MMMMMMM.MMMM... i* 3s engine naturally8aspirated or turbocharged MMMMMMMMM..MM.. <* 9ype of fuel used MMMMMMMM..MMM.. k* (uel consumption at rated output 'gals.;hr* MMMMM..MMMMMM.. l* Sump oil capacity 'Gals.* MMMMMM..MMMMM.. m* 9ype of cooling system MMMMMMMMM............ n* 9ype of gas purifier 'kg* MMMMMMMMMMMM TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 14 o* 9ype of silencer supplied MMMMMMMMMMMM p* Capacity of &ulk fuel tank supplied MMM.gallons for MMM.hours MMMMMMMMMMMM )* %ppro". dimension of service fuel tank 'inches* MMMMMMMMMMMM r* Capacity of day fuel tank supplied MMM..gallons for MMM.hours MMMMMMMMMMMM 2. DD9%3:S =( %:9D1@%9=1, %S (=::=/S a* Manufacturer MMMMMMMMMMMM b* Model or type @o. MMMMMMMMMMMM c* 1ated output 'k/* MMMMMMMMMMMM d* 1ated $oltage (re)uency 'AB* MMMMMMMMMMMM e* @o. of phases @o. of -oles MMMMMMMMMMMM f* Speed 'in 1.-.M* MMMMMMMMMMMM g* Class of insulation MMMMMMMMMMMM h* 3s alternator with brushes or brushless type MMMMMMMMMMMM i* 9ype of enclosure MMMMMMMMMMMM <* 9ype f e"citation MMMMMMMMMMMM k* %ppro". weight of alternator MMMMMMMMMMMM 4. DD9%3:S =( %:9D1@%9=1 C=@91=: -%@D: %S (=::=/S a* Manufacturer MMMMMMMMMMMM b* Dimensions of panel as follows MMMMMMMMMMMM i* :ength 'mm* MMMMMMMMMMMM ii* /idth 'mm* MMMMMMMMMMMM TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 15 iii* Aeight 'mm* MMMMMMMMMMMM c* 9hickness of m.s. sheet used in construction of panel 'S./.G* MMMMMMMMMMMM d* %ppro". weight of panel, it mounted separately from set 'kg* MM...MMMMMMMMM e* Colour finish of panel MMMMMMMMMMMM f* Details of overcurrent relay fitted on panel, as follows i* Manufacturer MMMMMMMMMMMM ii* Model of 9ype @o. MMMMMMMMMMMM iii* @o of -oles MMMMMMMMMMMM iv* State whether hand reset, Mechanical flag indicator is fitted MMMMMMMMMMMM v* 1ange of settings MMMMMMMMMMMM vi* Details of current transformers used, as follows Manufacturer MMMMMMMMMMMM Capacity of C;9s used MMMMMMMMMMMM Capacity of each C;9s 'in $%* MMMMMMMMMMMM C;9 Class MMMMMMMMMMMM C;9 1atio MMMMMMMMMMMM g* Details of Darth (ault 1elay (itted on -anel, as follows i* Manufacturer MMMMM............................ ii* Capacity of C;9s used MMMMMMMMMMMM iii* Capacity of each C;9s 'in $%* MMMMMMMMMMMM iv* C;9 Class MMMMMMMMMMMM v* C;9 1atio MMMMMMMMMMMM TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 16 h* Details of Dlectrical Measuring 3nstrument (itted on -anel, as followsN i* Manufacturer of voltmeter MMMMMMMMMMMM ii* Manufacturer of (re)uency Meter MMMMMMMMMMMM iii* Manufacturer of ?ilowatt Aour Meter MMMMMMMMMMMM iv* Details of %mmeter Scale MMMMMMMMMM........ v* 1ange of Setting MMMMMMMMMMMM vi* Details of current transformers to be used for %mmeter and ?ilowatt Aour Meter as follows MMMMMMMMMMMM Manufacturer MMMMMMMMMMM.... Capacity of each C;9s used MMMMMMMMMMMM Capacity of each C;9s 'in $%* MMMMMMMMMMMM C;9 Class MMMMMMMMMMMM C;9 1atio MMMMMMMMMMMM vii* Manufacturer or selector switches for %mmeter K voltmeter MMMMMMMMMMMM i* Give details of any other protective and;or measuring instruments installed on control panel, hereunder 5. DD9%3:S =( S9%193@G &%99D1H, %S (=::=/S a* Manufacturer MMMMMMMMMMMM b* 1ated $oltage of &attery Cells MMMMMMMMMMMM c* 9ype of &attery Cells MMMMMMMMMMMM d* Capacity of &attery 'in %h* MMMMMMMMMMMM 6. DD9%3:S =( &%99D1H CA%1G3@G J@39, %S (=::=/S a* Manufacturer MMMMMMMMMMMM b* 3nput $oltage '%.C* of charger MMMMMMMMMMMM TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 17 c* =utput $oltage 'D.C* of charger MMMMMMMMMMMM d* Ma". trickle charge current '%mps* MMMMMMMMMMMM !.. %31 D3SCA%1GD S3:D@CD1 a* Make MMMMMMMMMMMM b* Model MMMMMMMMMMMM c* Dimension MMMMMMMMMMMM d* %ir8/ay MMMMMMMMMMMM e* -ressure Drop MMMMMMMMMMMM f* =ctave &and, AB MMMMMMMMMMMM 9ransmission loss d& MMMMMMMMMMMM g* 3nfill Material MMMMMMMMMMMM h* 3nfill Material Density MMMMMMMMMMMM i* %ttenuation MMMMMMMMMMMM !!. %31 3@9%?D S3:D@CD1 a* Make MMMMMMMMMMMM b* Model MMMMMMMMMMMM c* Dimension MMMMMMMMMMMM d* %ir8way MMMMMMMMMMMM e* -ressure Drop MMMMMMMMMMMM f* =ctave &and, AB MMMMMMMMMMMM 9ransmission loss d& MMMMMMMMMMMM g* 3nfill Material MMMMMMMMMMMM h* 3nfill Material Density MMMMMMMMMMMM i* %ttenuation MMMMMMMMMMMM TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 1 !,. G%S DOA%JS9 S3:D@CD1 '-13M%1H* a* Make MMMMMMMMMMMM b* 9ype MMMMMMMMMMMM c* Model MMMMMMMMMMMM d* =ctave &and, AB MMMMMMMMMMMM 9ransmission loss d& MMMMMMMMMMMM e* D"haust pipe dia. MMMMMMMMMMM.... f* Silencer dia. MMMMMMMMMMMM g* Silencer :ength MMMMMMMMMMMM h* Silencer /eight MMMMMMMMMMMM i* %ttenuation MMMMMMMMMMMM !+. G%S DOA%JS9 S3:D@CD1 'SDC=@D%1H* a* Make MMMMMMMMMMMM b* 9ype MMMMMMMMMMM.... c* Model MMMMMMMMMMMM d* =ctave &and, AB MMMMMMMMMMMM 9ransmission loss d& MMMMMMMMMMMM e* D"haust pipe dia. MMMMMMMMMMMM f* Silencer dia. MMMMMMMMMMMM g* Silencer :ength MMMMMMMMMMMM h* Silencer /eight MMMMMMMMMMMM i* %ttenuation MMMMMMMMMMMM !0. =J9D==1 A=JS3@G TECHNICAL DATA AND SPECIFICATION FOR THE STANDBY DIESEL GENERATOR SET FOR MIMOS WAFER FABRICATION 2 AT TECHNOLOGY PARK MALAYSIA , BUKIT JALIL PAGE 1! a* Make MMMMMMMMMMMM b* 9ype MMMMMMMMMMMM c* Model MMMMMMMMMMMM d* Material MMMMMMMMMMMM 9ransmission loss d& MMMMMMMMMMMM e* D"haust pipe dia. MMMMMMMMMMMM f* Silencer dia. MMMMMMMMMMMM g* Silencer :ength MMMMMMMMMMMM h* Silencer /eight MMMMMMMMMMMM i* %ttenuation MMMMMMMMMMMM Company>s Stamp MMMMMMMMMM Signature MMMMMMM...