Professional Documents
Culture Documents
Fundamentos de GSM
Fundamentos de GSM
To solve the fundamental technical defects of the analog systems, the digital mobile
communication technologies emerged and the second generation mobile
communication systems represented by GSM and IS-95 came into being in the
middle of 1980s. The typical examples of the second generation cellular mobile
communication systems are the DAMPS of USA, the IS-95 and the European GSM
system.
The GSM (Global System for Mobile Communications) is originated from Europe.
Designed as the TDMA standard for mobile digital cellular communications, it
supports the 64 kbps data rate and can interconnect with the ISDN. It uses the 900
MHz band while the DCS1800 system uses the 1800 MHz band. The GSM system
uses the FDD and TDMA modes and each carrier supports eight channels with the
signal bandwidth of 200 kHz.
The DAMPS (Digital Advanced Mobile Phone System) is also called the IS-54
(North America Digital Cellular System). Using the 800 MHz bandwidth, it is the
earlier of the two North America digital cellular standards and specifies the use of
the TDMA mode.
The IS-95 standard is another digital cellular standard of North America. Using the
800 MHz or 1900 MHz band, it specifies the use of the CDMA mode and has
already become the first choice among the technologies of American PCS (Personal
Communication System) networks.
Since the 2G mobile communication systems focus on the transmission of voice
and low-speed data services, the 2.5G mobile communication systems emerged in
1996 to address the medium-rate data transmission needs. These systems include
GPRS and IS-95B.
The CDMA system has a very large capacity that is equivalent to ten or even twenty
times that of the analog systems. But the narrowband CDMA technologies come
into maturity at a time later than the GSM technologies, their application far lags
behind the GSM ones and currently they have only found large-scale commercial
applications in North America, Korea and China. The major services of mobile
communications are currently still voice services and low-speed data services.
With the development of networks, data and multimedia communications have also
witnessed rapid development; therefore, the target of the 3G mobile communication
is to implement broadband multimedia communication.
N-5
Fundamentos de GSM
Fundamentos de GSM
Fundamentos de GSM
Fundamentos de GSM
Fundamentos de GSM
10
Fundamentos de GSM
11
Fundamentos de GSM
12
Fundamentos de GSM
13
Fundamentos de GSM
14
Fundamentos de GSM
15
ITU has allocated 230 MHz frequency for the 3G mobile communication
system IMT-2000: 1885 ~ 2025MHz in the uplink and 2110~ 2200 MHz in the
downlink. Of them, the frequency range of 1980 MHz ~ 2010 MHz (uplink)
and that of 2170 MHz ~ 2200 MHz (downlink) are used for mobile satellite
services. As the uplink and the downlink bands are asymmetrical, the use of
dual-frequency FDD mode or the single-frequency TDD mode may be
considered. This plan was passed in WRC92 and new additional bands were
approved on the basis of the WRC-92 in the WRC2000 conference in the
year 2000: 806 MHz ~ 960 MHz, 1710 MHz ~ 1885 MHz and 2500 MHz ~
2690 MHz.
N-16
Fundamentos de GSM
17
Fundamentos de GSM
18
Fundamentos de GSM
19
Course Name
P-20
Course Name
P-21
Fundamentos de GSM
22
Fundamentos de GSM
23
24
UTRAN:
UE: User Equipment
Una red UTRAN incluye la RNC y el Nodo B.
RNS significa Radio Network Subsystem (Subsistema de la Red de radio), que se
compone de una RNC y los Nodos B bajo su control.
La interfaz entre la RNC y el Nodo B es la interfaz IUB. La interfaz IUR puede
configurarse entre dos RNC, esto es opcional, se utiliza para la cooperacin entre RNCs.
Una RNC est conectada al dominio CS a travs de la interfaz IU-CS y conectada al
dominio PS a travs de la interfaz IU-PS.
N-25
Fundamentos de GSM
CID: Cell ID
26
Fundamentos de GSM
27
Fundamentos de GSM
28
Fundamentos de GSM
29
Fundamentos de GSM
30
Fundamentos de GSM
31
Fundamentos de GSM
32
Course Name
P-33
Course Name
P-34
WCDMA RRM
N-35
WCDMA RRM
N-36
N-37
N-38
Durante el soft handover, dos o ms enlaces de radio estn conectados con UE, y los
datos en cada RL son iguales.
Los siguientes son algunos de los conceptos clave sobre la celda contigua en el soft
handover:
Conjunto activo: El conjunto de celdas utilizadas actualmente por el UE. El
resultado de la ejecucin de la transferencia blanda indica el aumento o
disminucin de las celdas en el conjunto activo.
Conjunto de monitoreo: El conjunto de celdas que no estn en el conjunto
activo pero estn siendo observados por el UE basado en la informacin de la
celda vecina de la UTRAN. El UE mide las celdas en el conjunto de observaciones.
Cuando los resultados de la medicin satisfacen ciertas condiciones, las celdas
pueden aadirse al conjunto activo. Por lo tanto, el conjunto de observaciones a
veces tambin se denomina el conjunto candidato.
Conjunto Detectado: El conjunto de celdas que han sido detectadas por el UE,
pero no pertenecen al conjunto activo o el conjunto de observaciones. La
UTRAN puede solicitar el UE para informar del resultado de la medicin del
conjunto detectado. Dado que las celdas en el conjunto detectado no se
enumeran en la lista de celdas vecinas, este conjunto es tambin llamado el
conjunto no listado.
N-39
No existe handover en esta diapositiva, slo un enlaces de radio conectado con UE.
N-40
N-41
Esto es soft handover. Durante el handover, las celdas en el conjunto activo pertenecen
a una RNC, pero Nodos B diferentes. Por lo tanto el UE puede combinar los datos en el
receptor RAKE. Pero en el enlace de subida, los datos se combinan con la combinacin
de seleccin en la RNC
N-42
Esto es soft handover. Durante el handover, las celdas en el conjunto activo pertenecen
a diferentes RNCs. Por lo tanto el UE puede combinar los datos en el receptor RAKE.
Pero en el enlace de subida, los datos se combinan con la seleccin en SRNC.
N-43
N-44
Fundamentos de GSM
46
Fundamentos de GSM
47
Fundamentos de GSM
48
Fundamentos de GSM
49
Fundamentos de GSM
50
Fundamentos de GSM
51
Course Name
P-52
Course Name
P-53
Course Name
P-54
Course Name
P-55
Course Name
P-56
Fundamentos de GSM
57
This Pgina indicates how the mapping can be done between logical, transport and
physical channels. Not all physical channels are represented because not all
physical channels correspond to a transport channel.
The mapping between logical channels and transport channels is done by the MAC
sub-layer.
Different connections can be made between logical and transport channels:
BCCH is connected to BCH and may also be connected to FACH;
DTCH can be connected to either RACH and FACH, to RACH and DSCH,
to DCH and DSCH, to a DCH or a CPCH;
CTCH is connected to FACH;
DCCH can be connected to either RACH and FACH, to RACH and DSCH,
to DCH and DSCH, to a DCH or a CPCH;
PCCH is connected to PCH;
N-65