You are on page 1of 96

iletisim: omarer25@hotmail.

com

www.forum.alghaform.com
iletisim: omarer25@hotmail.com
ALGHAFORM FORUMLARI PAYLASIMIDIR

www.alghaform.com

4 AutoFormOneStep

AutoFormOneStep has been developed to recognize forming problems quickly and effectively at a very early stage of product development and to modify the part geometry accordingly. The flexible
input in AutoFormOneStep permits the creation of a binder surface including the punch opening line. Thus AutoFormOneStep is
suited for a simple feasibility analysis and additionally for a quick
verification of a tool design and the comparison of different tool
concepts. The simulation of completely designed tools can be made
in extremely short calculation times. The seamless integration of
AutoFormOneStep with the AutoFormOptimizer helps you finding optimized geometry and process parameters.
The inverse formulation of AutoFormOneStep allows for the simple and precise determination of the blank outline and thus the minimal material requirements. This opens new perspectives for
quotations/estimations as well as for tool design considering the
optimized blank and thus the minimal material consumption.
The integration with all other AutoForm products makes many
additional functions available such as AutoFormDieDesigner or
AutoFormOptimizer for the optimization of the part geometry,
binder surfaces, addenda or process parameters.
AutoFormOneStep supports five different calculation types, which
require different forming knowledge of the user and are used for
different tasks:
Part only (1-step)

The calculation is exclusively based on the part geometry; starting


from the part geometry the flat blank is calculated (inverse calculation method). The specification of the part boundary line allows for
the simple modification of the part boundary.
This simplest calculation type requires the least forming knowledge
of the user and is especially suited for forming analyses during part
design as well as for the estimation of the forming complexity of the
part and for the determination of the minimal material consumption for quotation and estimation purposes. As the impact of the
addendum is only considered by restraining forces on the part

boundary, the accuracy of a Part only calculation is coarse, especially along the part boundary.
This calculation type does not directly determine the flat blank but
the curved blank, which in the real forming process conforms to the
shape of the sheet after binder closure. The binder surface has to be
defined. A two step process is simulated:

Part only (2-step)

Friction free binder closure involving no restraining force


Deep drawing involving friction and restraining forces
The remarks of the preceding paragraph obtain indeed this calculation type provides more realistic results for parts with
extremely curved binder surfaces. Since there is no real addendum
involved in the calculation, it is important to have an especially
realistic binder as used in the real tool. Yet it is sufficient if the surface tolerably conforms to the part contour to improve the quality of
the calculated results.
For this reason, this method is useful for the part designer who does
not necessarily have a deep understanding of the forming process.
Based on the defined binder surface and punch opening line, AutoFormOneStep automatically generates a simple addendum, running out of the part boundary tangentially and running into the
binder surface on the punch opening line tangentially. The calculation is based on the part and the addendum using the two step
method. If a realistic binder surface is available, this calculation
type improves the quality of the results considerably compared to
the Part only calculation, because a rough geometric addendum is
taken into account the simulated process is thus closer to the real
forming process.

Part+Binder (2step)

This calculation type is especially wellsuited for rapid verification


and comparison of different tool concepts. Since the binder essentially influences the addendum and hence the results, the user
should possess the essential forming knowledge about the generation of binder surfaces.
The calculation is based on the completely defined tool. The punch
opening line and the flange boundary line at the end of the forming
process have to be defined. These two lines determine the flange
surface, on which binder pressure is applied to control material
flow. The Full tool calculation type gives the most precise results of
all OneStep calculation types.

Full tool (1-step)

www.alghaform.com

www.forum.alghaform.com

This approach is wellsuited for the verification of tool concepts,


developed e.g. in AutoFormDieDesigner. As the blank outline
after forming (OS boundary) has to be defined due to the inverse
calculation method, precise minimal precut parts can be determined, which can then be used as initial blank for an incremental
simulation. The 1-step option of the Full tool calculation is suited
for tool with plane binder surfaces.
Full tool (2-step)

As for a Part only (2-step) calculation the binder surface is determined at first binder closure is accomplished without friction and
retraining forces.
This calculation type is used for tools with a curved binder.
As for Full tool simulations the restraining forces in the binder surfaces are of essential importance for the results, the 2-step option
should be preferred otherwise the simulation assumes that the
restraining forces in the binder surface already apply for binder closure. That does not correspond to the real forming process and may
lead to a significant overestimation of strains. Besides the remarks
on the Full tool (1-step) calculation type obtain.
The necessary geometric input data for the five simulation type are
summarized in the following table:
Full tool

Full tool

(2 - step)

Part +
Binder
(2 - step)

(1 - step)

(2 - step)

part

part

part

die

die

Binder surface

no

yes

yes

no

yes

OS boundary

pb line

pb line

f line

f line

f line

OS punch
opening

no

no

yes

yes

yes

Part only

Part only

(1 - step)

Part/Tool
geometry

Legend:
pb line = part boundary line
f line = flange line
www.alghaform.com

AutoForm offers a geometry module named AutoFormPartDesigner for the advanced use of AutoFormOneStep in feasibility
analyses during part design. It makes possible the optimization of
forming parameters in the most important geometric modifications
of the part in AutoForm:
Automatic generation of variable fillets on the product
geometry
Rapid determination of the best fillet radius for forming
Determination of the die tip (drawing direction)
Automatic geometry creation to fill designed holes
Boundary fill by filling concave inlets: The accuracy and
usability of the Part only results increase significantly in
the outer boundary area of the part.
Modification of geometry regions by cutting and controlled filling
Overcrowning of entire part regions
Automatic and interactive development of binder surfaces:
The accuracy of the simulation increases significantly for
the Part only (2-step) calculation type.
Fully parametrized treatment of input data to facilitate the
optimization with AutoFormOptimizer
AutoFormOneStep provides five different simulation
types.
For certain functions described in this workshop the AutoForm
PartDesigner must be available. The respective functions are
marked.
One of the most important features of AutoFormOneStep Version.
3.1 is the greatly improved userfriendliness and the ease with
which the simulations are set up, run and evaluated. The Onestep
wizard has been developed for the Part only simulation. This wizard makes it possible to run feasibility studies quickly and reliably
considering different process parameters in a single simulation

www.forum.alghaform.com

www.forum.alghaform.com

Contents of the Workshop AutoFormOneStep


Lesson 1

Part only Simulation with OneStep Wizard . . . . . . . . . . . . . . . . 6

Lesson 2

Part only (2-step) Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Lesson 3

Importing CAD data


Determining the drawing direction
Defining holding conditions
Evaluating the OneStep simulation

Variable Restraining Option


Preparing the geometry
Part boundary
Binder surfaces

Part + Binder (2-step) Simulation


Simulation.. . . . . . . . . . . . . . . . . . . . . . . 37
Filling holes
Boundary fill
Automatic binder generation (Auto Binder)

Lesson 4

Full tool (1-step) Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Lesson 5

Full tool (2-step) Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Lesson 6

Full tool
Tailored blank
Linear weld line
Material mark
Material lines

Drawbead
Symmetry
Optimizing the blank
Importing and exporting lines

Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Numerical optimization
Parameter study
Optimization of the force factor
Optimization of the force factor of a drawbead
Evaluating the optimization
5

Lesson 1: Part only Simulation with OneStep Wizard

4. 1 Lesson 1: Part only Simulation with OneStep Wizard


This lesson presents a simple example for AutoFormOneStep. Using AutoForm
OneStep is it possible to run a feasibility analysis for the part geometry in a fast and
straightforward manner.
Fig. 1.1

Geometry for the OneStep simulation

Setting up the Simulation File


At the start of the OneStep simulation, you have to define the simulation file (*.sim). This simulation file contains all the information
about the calculation (geometric input, process parameters, numerical values ...) and finally the results of the computation. Set up the
simulation file using the following command:
File > New onestep ...
The window OneStep wizard (for a OneStepPart only simulation)
opens (Fig. 1.2):

www.forum.alghaform.com

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Fig. 1.2

OneStep wizard

Importing the Part Geometry


The geometry import is carried out using the module afmesh, the
integrated IGES/VDAFS interface, which automatically meshes the
part geometry. The part geometry needs to be available as surface
model containing the inner or outer side of the part geometry. The
following formats are supported for import: af, afb (binary AutoformFormat), Nastran, Dyna and Stl.
For this lesson a VDAFS file is available. Import this file:
OneStep wizard

Import ... > VDAFS > OK > Files: os_lesson_01.vda > OK >
afmesh_3.1 > OK

Fig. 1.3

Import geometry

Lesson 1: Part only Simulation with OneStep Wizard


Fig. 1.4

Afmesh
Options for meshing the CAD data
Error tolerance: Allowable chordal error tolerance for the
meshing. Value is taken from New file dialog (Default: 0.1)
(Fig 1.1), but it can be changed. For especially small radii
(equal or lesser than 2 mm) 0.05 should be used as error
tolerance.
Max side length: Maximum element side length. Default
setting: 50.

Parameters

Treat only: Only specified faces will be meshed. Possible


entries are e.g. 1, 2, 6-8.
Exclude: The specified faces are not taken into account for
meshing. Possible entries are e.g. 1, 2, 7-9.

Faces

Treat only (for IGES import only): Only specified layers


will be meshed.
Exclude (for IGES import only): The specified layers are
not taken into account for meshing.

Layers

The meshed part geometry is immediately displayed in the main


display.

www.forum.alghaform.com

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Fig. 1.5

OneStep wizard
Enter a project identifier into the field Title of the OneStep wizard.
This identifier will be always be indicated in the bottom of the user
interface.
Note:
Note A title is automatically suggested including the current file
name, the user name and the date of creation.
OneStep wizard

Title: lesson_01
The following three areas of the OneStep wizard have to be specified to prepare the simulation:
Geometry
Blank
Process

Lesson 1: Part only Simulation with OneStep Wizard


First, the part geometry has to be rotated such that the drawing
direction corresponds to the zaxis and no backdrafts occur in the
part. Use the buttons in the field Tip.
Checking for Undercuts
Click the Backdrafts button in field Display.
Geometry > Display > Backdrafts
Faces containing undercuts will be displayed red in the main display (Fig. 1.6)
The meaning of the colors:
Safe (green): Backdraft angle greater than 3 degrees
Marginal (yellow): Backdraft angle between 0 and 3
degrees
Severe (red): Areas containing undercuts smaller than 0
degree
The part contains undercuts, thus it has to be tipped into drawing
direction. To determine a proper drawing direction we recommend
using the automatic function Min backdraft:
Geometry > Tip > Min backdraft
This function calculates a drawing direction with minimum undercuts.
Fig. 1.6

Backdrafts:
Backdrafts Representation of areas containing undercuts
www.forum.alghaform.com

10

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

The part contains no undercuts in the calculated drawing direction


(Fig. 1.7). In case the tipping direction calculated with the automatic
functions do not result in an acceptable drawing direction, use the
manual functions (Tip: x-axis/y-axis) to modify the drawing direction.
Fig. 1.7

Undercut free part geometry


Having tipped the part geometry, you can now apply filleting in the
areas containing sharp edges globally and fill the part boundary.
Adjust the representation in the main display as follows:
Geometry > Display > Faces
Global Filleting of all sharp edges in the part geometry
Use the following command to fillet sharp edges:
Geometry > Fillet > Radius: 3
Filling the Part boundary
Generate the boundary fill now. Fill areas are created automatically
along the part boundary. The outer boundary fill line is determined
by a roll cylinder moving around the part boundary and its roll
radius:
Geometry > Boundary fill > Roll radius: 100.00

11

Lesson 1: Part only Simulation with OneStep Wizard


To start the global filleting and the creation of the boundary fill and
the generation of the resulting part boundary, click
Apply
The resulting geometry containing the generated part boundary is
shown in Fig. 1.8. The part boundary has changed during the creation of the boundary fill (see also Fig. 1.9 and Fig. 1.10).
Fig. 1.8

The resulting geometry and the part boundary


Fig. 1.9

Detail:
Detail Part boundary before boundary fill

www.forum.alghaform.com

12

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Fig. 1.10

Detail:
Detail Part boundary after boundary fill
The geometry has been completely prepared for the simulation.
Define the sheet thickness and select a material:
Defining Material Properties
Blank > Thickness: 1
Blank > Material > Import ... > Select material > zste180bhZ_1.mat
> OK
Define the restraining forces on the part boundary in the area Process. Different holding conditions can be used. The holding condition Free corresponds to ideal deep drawing, e.g. for tools without a
binder. In contrast the holding condition Locked corresponds to
stretch forming, e.g. for tools with extremely high binder pressure.
Restraining forces, corresponding to a usual tool in which material
drawin occurs, can be defined by means of weak, medium, strong
and User defined.
The current simulation will be calculated using standard settings
(Free, Medium and Locked).
The complete input for the simulation is shown in Fig. 1.11.

13

Lesson 1: Part only Simulation with OneStep Wizard


Fig. 1.11

OneStep wizard:
Part only simulation
wizard Prepared OneStepPart
Store the prepared simulation and start the simulation:
File > Save as ... > os_lesson_01.sim > OK
Start ... > Program: afos_3.1 > Start
Note:
Note The OneStep wizard contains a number of selected functions
for the definition of the simulation. Use the Advanced ... button to
access additional functions in AutoFormOneStep. These additional functions will be described in the following lessons.

www.forum.alghaform.com

14

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Evaluating Simulation Results


The following section describes the most important result variables
of a OneStep simulation. Having completed the calculation of the
simulation, reopen the SIM file using the command:
User interface

File > Reopen


The main display shows the calculated part geometry. In the lower
part of the user interface, three buttons are available: free, medium
and locked. Click one of the buttons to load the results for the
respective holding condition from the SIM file. Compare the results.

Fig. 1.12

The user interface after loading the calculated simulation


Formability
The result variable Formability gives you a general survey of the
feasibility of the part. Areas undergoing different stresses are colored differently on the part:
Cracks (red): Areas of cracks. These areas are above the
FLC of the specified material.
Excess. Thinning (orange): In these areas, thinning is
greater than the acceptable value (default value for steel is
30%).

15

Lesson 1: Part only Simulation with OneStep Wizard


Risk of cracks (yellow): These areas may crack or split. By
default, this area is in between the FLC and 20% below the
FLC.
Safe (green): All areas that have no formability problems.
Insuff. Stretching (gray): Areas that have not enough
strain (default 2%)
Wrinkling tendency (blue): Areas where wrinkles might
appear. In these areas, the material has compressive
stresses but no compressive strains
Wrinkles (purple): Areas where wrinkles can be expected,
depending on geometry curvature, thickness and tool contact. Material in these areas has compressive strains which
means the material becomes thicker during the forming
process.
Select the result variable Formability. Compare the results for the
different restraining forces. The results for the holding condition
free is shown in Fig. 1.13,
medium is shown in Fig. 1.14 and
locked is shown in Fig. 1.15.
Fig. 1.13

Formability with holding condition free

www.forum.alghaform.com

16

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Fig. 1.14

Formability with holding condition medium


Fig. 1.15

Formability with holding condition locked

17

Lesson 1: Part only Simulation with OneStep Wizard


You can see from the figure that the part is insufficiently stretched,
using the holding conditions free and medium. There are several
areas containing wrinkles (purple), wrinkling tendencies (blue) and
insufficient stretching (gray). Using the holding condition locked,
the part is sufficiently stretched. A small area of insufficient stretching (gray) can be seen on the left end (Fig. 1.15).
Thinning
Switch to the result variable Thinning (second row of icon panel in
main display, middle button). A scale is displayed in the lower part
of the main display with a range of 30% thinning to 3% thickening
(depending on the specified color settings) (Fig. 1.16).
Fig. 1.16

Thinning (in percentage) with the holding condition locked


The exact thinning value (in percentage) is displayed, when you
click with the right mouse button on the geometry. Hit the Esc key
to clear these labels from the display. To find the maximum thinning and the maximum thickening of the part use the following
options
Results > Show max
Results > Show min

User interface

www.forum.alghaform.com

18

www.forum.alghaform.com

Lesson 1: Part only Simulation with OneStep Wizard

Close AutoFormUser Interface


The user interface can be closed with following option:
File > Quit or hotkey Ctrl Q.

The area Geometry (OneStep wizard)


Use the functions of this area to check if the meshed part geometry
is suitable for the simulation (undercuts and sharp edges) and to
prepare the geometry for the simulation. The following functions
are available:
Symmetry: Define the symmetry plane for symmetrical
parts. This definition is possible for the values X = 0, Y = 0
or no symmetry.
Tip: Determines the drawing direction of the part.
Min backdraft: Calculates a drawing direction with minimum undercuts.
Screen axes: Uses the normal of the display as drawing
direction.
Reset: Uses the original axis of CAD data (zaxis) as drawing direction.
X- and Y-axis: Allows for the manual rotation by a defined
angle about the x or yaxis.
Del picked: Removes selected faces from the meshed
geometry.
Del backdraft: Removes faces containing undercuts from
the geometry.
Undel picked: Deleted faces are restored.
Undel all: All deleted faces are restored.
Display: Switch for the representation
Faces: Each face is represented by another color.
Objects: The geometry is represented by a single color.
Backdraft: The geometry is automatically checked for faces
containing undercuts. The faces are colored green for safe
areas, yellow for areas with marginal undercuts and red
for areas containing severe undercuts.
Deleted: Deleted faces are displayed again.
Part boundary: The part boundary needed for the simulation is generated.
Error tolerance: Acceptable chordal error for the part
boundary. The value can be changed. For especially small
radii (equal or lesser than 2 mm) 0.05 should be used as
error tolerance.

19

Lesson 1: Part only Simulation with OneStep Wizard


Fillet: The geometry is checked for sharp edges. The sharp
edges are filleted by the defined radius automatically
(Radius:).
Boundary fill: Holes are filled and the boundary fill is created (Roll radius:).
Apply: Use the Apply button to execute all functions
defined.

The area Blank

Thickness: Sheet thickness


Material: Material
Import ...: Import a material from the material database
View ...: Shows the current material properties
Input ...: Defining material properties

The area Process


Use the functions of this area to define the restraining forces (Holding conditions). The following holding conditions are available:

Free: No restraining forces (ideal deep drawing)


Weak (0.15): Weak restraining forces
Medium (0.35): Medium restraining forces
Strong (0.9): Strong restraining forces
Locked: Locked (stretch forming)

Besides the above conditions, it is also possible to enter freely


defined values (User def.). Decide which of the holding conditions
will be used for the simulation. Click All to use all holding conditions, click None to use no holding condition. The simulation is calculated separately for each of the defined holding conditions. By
default the three holding conditions (Free, Medium and Locked)
are set. In version 3.1, all OneStep results are stored in a single SIM
file thus eliminating the need for manual iterations with different
conditions being stored in separate files.

www.forum.alghaform.com

20

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

4. 2 Lesson 2: Part only (2-step) Simulation


The functions introduced in this lesson make possible the more precise definition of
restraining forces in AutoFormOneStep. Besides the Part only (2-step) simulation calculates the developed blank more precisely. This simulation type requires the definition of
a binder surface in addition to the inputs required for a Part only (1-step) simulation.
This simulation proceeds in two steps:
Simulation, in reverse, of the drawing process from binderwrap to the final product geometry. The reverse process
takes into account friction as well as the restraints applied
to the OS boundary, and establishes the outline of the
developed blank mapped on to the geometry of the curved
binder surface.
Simulation, in reverse, of the binderwrap process. During
this process, no restraints are applied on the sheet, and the
developed blank outline is unfolded from the curved
binder surface on to the flat surface.
The above 2step approach is more representative, particularly in
the case of curved and deepdrawn parts, of the actual stamping
process. Therefore, results of 2step simulations are more accurate
for these parts, and are closer to those of an incremental process
simulation.
Fig. 2.1

Cross member geometry including the binder surface


User interface

Setting up a new Onestep Simulation


File > New onestep to open the OneStep wizard.

Importing and Editing the CAD geometry


Use the following commands to import the CAD data:
OneStep wizard

Import ... > VDAFS > OK > os_lesson_02.vda > OK > Program:
afmesh_3.1 > OK
21

Lesson 2: Part only (2-step) Simulation


The crossmember geometry is displayed in the main display, and
the OneStep wizard is filled with a few default values.

Editing Parts Faces


There is an upstanding flange around one of the holes of this part. If
this flange were to remain on the part geometry during simulation,
a prediction of cracks would result at the flange. However, since
these flanges would be formed in a secondary operation, they may
be ignored in the OneStep simulation without any errors, and may
therefore be eliminated as follows: Hold the Shift key down and
use the right mouse button to pick the flange faces. Click the Del
picked button to remove the faces from the geometry. The remaining faces form the part, i.e. it is only these faces that are taken into
account during subsequent simulation.
Fig. 2.2

Selected flange faces for deletion


Del picked deletes selected faces.

www.forum.alghaform.com

22

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

Fig. 2.3

Representation of deleted faces


The deleted faces are represented as a mesh. Select the faces and
subsequently use the buttons Undel picked or Undel all to add the
faces back to the part again.

Establishing the Drawing Direction


In preparation for a simulation, the imported product geometry
needs to be rotated so that the drawing direction for the product is
parallel to the zaxis: There should be no backdraft faces on the
geometry relative to the zdirection. There are several manual or
automatic options that you may apply to establish the required die
tip. The ideal die tip may be established in the present case using
the Min Backdraft option:
Display: Backdrafts shows backdrafts on the geometry.
Tip: Min backdraft reorients the product geometry such that the
product faces, on average, have the largest possible inclination to
the zdirection.

23

Lesson 2: Part only (2-step) Simulation


Fig. 2.4

Reoriented geometry with representation of backdrafts

Generating the Part Boundary


(Outer boundary of the product geometry)
After editing the product geometry, the boundary of the current
geometry may be generated automatically by clicking the Apply
button.
Display: Objects shows the geometry in colored and shaded mode.
Apply in the field Geometry generates the part boundary.

www.forum.alghaform.com

24

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

Fig. 2.5

Geometry with part boundary

Defining the Material Properties


The default material selection is FeP04; an alternate material file
may be selected from the extensive material library using the
Import ... button.
Blank: Import ... to open the dialog Select material.
Use the buttons View or Preview to display the properties of the
selected material: Hardening curve, forming limit curve and rvalues.
Fig. 2.6

Select material / Preview


25

Lesson 2: Part only (2-step) Simulation


Files: zste220P_1.mat > OK

The Advanced Mode


All necessary information has been entered into the OneStep wizard. The settings in the area Process are left unchanged.
Fig. 2.7

OneStep wizard containing all information


Additional information is entered in the Advanced mode. Click
OneStep wizard

Advanced ...
The dialog AutoForm - Question pops up:

Fig. 2.8

AutoForm - Question
Finish closes OneStep wizard and opens AFOS input generator.
www.forum.alghaform.com

26

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

Fig. 2.9

AFOS Input generator


The full function range of the AFOS input generator will be
described in one of the following lessons. For this example only the
pages Geometry and Process are used. For the following steps, we
require a license for AutoFormPartDesigner.

27

Lesson 2: Part only (2-step) Simulation

Preparing a Binder Surface


Open the Geometry generator.
Model > Geometry generator ...

User interface

Generate a binder on the Binder page.

Binder
Fig. 2.10

Geometry generator: Binder page


Auto > Apply (Leave the default settings unchanged)

Binder

www.forum.alghaform.com

28

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

A log window pops up containing information on the progress of


the binder surface calculation.
Fig. 2.11

Log window
The product geometry and a curved binder are shown in the main
display.
Fig. 2.12

Product geometry with binder

Selecting the Geometry Type


Select the geometry type Part only (2-step) on the Geometry page
of the Input generator.
Part only (2-step)

Geometry

29

Lesson 2: Part only (2-step) Simulation


Fig. 2.13

Geometry Type Part only (2-step)


In addition to the product geometry there is a binder surface now.
The OS boundary has been copied depending on the part boundary.

Variable Restraining Options


In a lot of cases, a constant magnitude of restraining force applied to
the OS boundary in a Part only simulation does not lead to optimal
predictions of product quality. For example, localized areas may be
insufficiently stretched, or may have very large strains close to or
exceeding the forming limit (leading to a prediction of cracks). In
such cases, it would be useful to vary the holding conditions
around the OS boundary to achieve optimal stretch conditions over
the entire product geometry without causing splits, cracks or excessive thinning.
Medium > Restraining options > Variable
Enter the restr into the field Name:

30

Process

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

Holding condition > Name: restr


Fig. 2.14

Restraining options Variable


Before selecting nodes along the part boundary using the function
Input points ..., we recommend to adjust the view from zdirection.
User interface

View > From +Z (yx) and


View > Fit to window
This can also be done using the keyboard by pressing Ctrl Z for
the view orientation followed by Ctrl W to fit to window.

Input generator

restr > Input points


The dialog for the definition of nodes opens:

31

Lesson 2: Part only (2-step) Simulation


Fig. 2.15 a

Definition of restraining forces


Add/edit point
Fig. 2.15 b

Definition of the force factor


In the main display many nodes are shown along the part boundary. Select any of these nodes using the right mouse button and
define a specific restraining force factor value at each of the selected
nodes.
OK to finish the definition of nodes.
The actual restraining force variation over a segment is interpolated
linearly between values set at the nodes bounding this segment.

32

www.forum.alghaform.com

Lesson 2: Part only (2-step) Simulation

The figure below shows a total of 15 restraining point defined over


the OS boundary of the cross member geometry.
Fig. 2.16

15 nodes with different forcefactors


Fig. 2.17

Variable restraining forces


User interface

Evaluation of the results


File > Save as > os_lesson_03.sim to save the input data.
Job > Start simulation ... > Start to start the calculation.
File > Reopen reads the results.
To review the results for the variable restraining forces, click the
button restr at the bottom of the AutoFormUser Interface.
restr

33

Lesson 2: Part only (2-step) Simulation


Click the button for the result variable Formability:

Fig. 2.18

Formability with variable restraining forces


Besides the representation of the part with the result variable and
the developed blank the representation of the binderwrap is available now.
Use the three buttons on the lower left side of the AutoFormUser
Interface to select the desired representation.

34

Lesson 2: Part only (2-step) Simulation

www.forum.alghaform.com

shows the binder-wrap.


Fig. 2.19

Binderwrap

35

Lesson 2: Part only (2-step) Simulation


shows the developed blank.
Fig. 2.20

Developed blank

36

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

4. 3 Lesson 3: Part + Binder (2-step) Simulation


This simulation type is useful in the initial phase of methods and process planning when
only the part geometry is available. By enabling quick and interactive generation of
binder surfaces based on product geometry, and by allowing the binder surface to be
used in the simulation, it becomes possible to assess the influence of these tool surfaces on feasibility, and possibly to optimize these and associated process parameters
in conjunction with product geometry in early stages itself.
Fig. 3.1

Part geometry
The procedure in creating and defining inputs and in running simulations of this type is as follows:
User interface

File > New > File name: lesson_os3


Units: mm and N
Geometric error tolerance: 0.1 > OK

Geometry generator

File > Import > VDAFS > OK > File: lesson_os3.vda > OK

Prepare

Symmetry / double > x-z-plane y: 0 > OK > Apply

37

Lesson 3: Part + Binder (2-step) Simulation


Fig. 3.2

Sharp Edges
Go to the Fillet page to determine the sharp edges of the geometry.
Check radius: 2.00 > Check > OK

Fillet

The areas on the part containing sharp edges are displayed.


Fig. 3.3

Areas containing sharp edges


Areas in the part containing sharp edges are displayed. It is necessary to fillet all sharp edged areas in the part. There are two ways to
fillet sharp edges: Globally with a global fillet radius or locally with
38

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

a constant or variable radius or radius transition. We will describe


all these variants.
Global Filleting
Global fillet radius: 3.00 > Apply
All areas containing sharp edges will be filleted using a radius of 3
mm.
Local Filleting by a Constant Radius (requires AutoFormPartDesigner license)
In order to generate variable radii at individual edges, the edges
need to be identified and the radii need to be specified. Click the
Add line ... button at the bottom of the Fillet page to identify sharp
edges.
Add line ... opens the window containing the message: Mark
radius control edge. Finish with double click.
Selecting an edge also involves identifying the length along the
edge that will be filleted. Edges have to selected one after the other,
each time clicking the Add line ... button to start a new selection.
Fig. 3.4

Local filleting

39

Lesson 3: Part + Binder (2-step) Simulation


Click once with the right mouse button to select the starting point at
an edge of interest, let go the mouse button and move your mouse
cursor along the curved outline of the edge. This progressively
highlights (in yellow) the length of the edge. Double click the right
mouse button to end the edge selection.
Note:
Note If the run of the curve representing the edge is ambiguous
(long, extremely curved edge or branchings along the curve), set
intermediate points to define the run of the curve precisely. Click
the right mouse button repeatedly along the curve representing
the edge.
Add line ...

Fillet

Mark the entire curve, as shown in Fig. 3.4.


line1: > Constant > Constant fillet radius: 5.00 > Apply
Local Filleting by a Variable Radius (requires AutoFormPartDesigner license)
To generate variable fillets, the edges to be filleted need to be
selected as described above. Subsequently, radius control points
are selected on each of these edges, and radius values are specified
at each of these points.
Add line ... > line2: > Variable > Selecting 4 radius control points >
OK

40

Fillet

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

Fig. 3.5

Locally filleted edges


Fillet

Assign a radius to each of the control points.


Finally click the button
Apply

41

Lesson 3: Part + Binder (2-step) Simulation


The Fillet page is as shown in Fig. 3.6:
Fig. 3.6

Fillet page

Definition of Drawing Direction


It is necessary to rotate the imported geometry from vehicle to draw
position in order to eliminate backdraft conditions.

42

Tip

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

Fig. 3.7

Backdraft faces on the part geometry


Incremental tipping > Y-axis > by degrees: 45 > rotate: The part is now free of undercuts.
Modify P page (requires AutoFormPartDesigner license)
Use the functions of the Modify P page to fill holes contained
within the part geometry.
Modify P

All holes > Define holes > Min size: 1.50 > Max size: 300.00 >
Apply
Use the functions of the Bndry page to fill of areas on the part
boundary:

Bndry

Add Bndr fill ... > Curve 1 > OK > Fill parameters: Bndry fill roll
radius: 300 > Apply
Note:
Note Smoothening the part boundary increases the accuracy of
the simulation results on the part boundary, especially for concave
regions.

43

Lesson 3: Part + Binder (2-step) Simulation


Fig. 3.8

Filling holes and boundary fill


Generate the binder surface on the Binder page using the AutoBinder function (requires AutoFormPartDesigner).
Auto
For the binder a minimum drawing depth is required.
Drawing depth: Minimum
The main curvature direction of the binder is defined in ydirection,
i.e. by an angle of 90.
Profile orientation > Angle: 90 deg

44

Binder

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

Fig. 3.9

Auto Binder page


Binder

Apply
A curved binder surface has been generated. Analyze the distance
between the binder and the part in the AutoFormUser Interface.
Adjust the value range of the result scale for the current example:
Geometry generator > Display > Ranges > Min/Max Simulation

45

Lesson 3: Part + Binder (2-step) Simulation


Fig. 3.10

Plot of the drawing depth distribution on the part geometry


Fig. 3.11

Adjusting display range


Click any area of the part with the right mouse button to display the
actual drawing depth value. Change the distance between binder
and part using the function Binder position Shift.
The preparation of the part geometry has been finished for the simulation. Define the process parameters in the Input generator:
Model > Input generator > Simulation type: OneStep > OK

User interface

AFOS input generator


Enter the title of the simulation. Enter further information on the
current simulation into the field Comment.

Title

46

www.forum.alghaform.com

Geometry

Lesson 3: Part + Binder (2-step) Simulation

Type: Part+binder (2-step) > Delete the current OS boundary line?


> Delete

Fig. 3.12

Geometry type: Part + Binder (2-step)


The definitions of part and binder geometries have been automatically accomplished by transferring data of the imported part geometry and generated binder surface from the Geometry generator.
The sheet thickness for the part is 1.2 mm. By specifying an offset of
0.6 mm (Upwards), the simulation may be carried out on the midsurface of the product geometry an Upwards offset is used since
the imported surface represents the lower surface of the product.
Geometry

Part > Offset: 0.6


Definition of the Punch Opening Line
The punch opening line is used to define areas in which the generated mesh for the addendum has a tangential transition to the
binder.

47

Lesson 3: Part + Binder (2-step) Simulation


OS punch opening line
Dependent ... > Bndry (Bndry) > OK
The Bndry (Bndry) line defines the part boundary including the
outer boundary fill areas. It has to be adapted using the functions
Expand and Smooth of the Curve editor. The adapted line will be
used as punch opening line.
Fig. 3.13

Select Curve dialog


OS punch opening > Edit ... > Expand: 15 > Smooth: 0.05 > OK
Fig. 3.14

Curve editor:
editor OSPO line
The same approach using the geometry of the Bndry (Bndry) line
as the starting point for defining another line may be employed to
accomplish the definition of the OS boundary line. This line represents the outer edge of the formed sheet at the end of the forming/
drawing process. Starting from the geometry of the Bndry (Bndry)
line, Expand and Smooth options may be used to define the OS

48

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

boundary line, making sure to differentiate it from the previously


defined OS punch opening line.
OS boundary > Dependent ... > Bndry (Bndry) > OK
Edit ... > Expand: 90 > OK > Smooth: 0.1 > OK
Fig. 3.15

OS POline and OS boundary


Blank

Thickness: 1.2 > Material: zste340_3

Fig. 3.16

Blank page
Lube

Definition of Friction
Lubrication > Constant > Standard 0.15

49

Lesson 3: Part + Binder (2-step) Simulation


Fig. 3.17

Process page

Definition of the Process Parameters


Holding Conditions > Type: Binder pressure

Process

Pressure options > Pressure: 6 (default)


Note:
Note The binder pressure is defined relative to the final flange
area. Thus a higher pressure has to be defined than for an incremental simulation, for which the pressure is defined with respect to
the initial flange area.
Accuracy > Mesh: Standard
Starting the Simulation
Job > Start simulation ... > Save > Start

Evaluating the simulation


File > Reopen

Control
AFOS input generator
User interface

As a result of the simulation you can evaluate three different


phases.
Developed blank
The outline of the developed blank is computed during the simulation. The edge of this blank may be exported in af, IGES or VDAFS
format, and may be used to define the blank in an AutoFormIncremental simulation. Blank outline may be exported as follows:
File > Export boundaries > ...

50

User interface

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

Fig. 3.18

Developed blank
Binderwrap
The result of the OneStep calculation is iterated in the binder surface considering friction. Particular high strains are thus avoided for
highly curved binders.

51

Lesson 3: Part + Binder (2-step) Simulation


Fig. 3.19

Binder wrap
Formed sheet
AutoFormOneStep offers among others the following results:
Distribution of strain and all dependent variables such as
sheet thickness, failure, wrinkling, hardening, forming
limit analysis and stress
Binder pressure distribution in the flange area
Distribution of sheet reaction stress
Friction shear stress
Formability etc.

52

www.forum.alghaform.com

Lesson 3: Part + Binder (2-step) Simulation

Fig. 3.20

Formed sheet: Formability


In the example a review of the socalled Formability map of the
simulation geometry reveals a large region to be insufficiently
stretched.
Do as follows to improve the predictions of uniform stretching:
Modify the binder pressure value to 10 N/mm, a value suitable for
the higher thickness (1.2 mm) and higher strength sheet material.
After modifying the simulation input data, save these to a new simulation file, run the simulation and review the results.

53

Lesson 4: Full tool (1-Step) Simulation

4. 4 Lesson 4: Full tool (1-Step) Simulation


This lesson describes a OneStep simulation based on a tool geometry with a tailored
blank. In addition, that the weld line position is optimized in such a way that the original
blank contains a linear weld line thus reducing costs for the blank.
Fig. 4.1

Tool geometry

Setting up a new Simulation


File > New > File name: os_lesson_4 > Length: mm > Force: N >
Geometric error tolerance: 0.1

User interface

File > Import... > VDAFS > OK > Files: os_lesson_4.vda > OK

Geometry generator

Error tolerance: 0.1 > Max side length: 50 > OK

AFMesh window

54

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Definition of the Binder


The meshed tool geometry is shown in the main display. Use the
right mouse button to click on the binder surface of the tool geometry. The selected surface is highlighted in yellow. Click on the
Binder button on the Prepare page of the Geometry generator to
save these faces in the Binder register.
Fig. 4.2

Selecting the binder surface

55

Lesson 4: Full tool (1-Step) Simulation

Calculation of the Part boundary


Part boundary generation > Error tolerance: 0.1 > Concatenation
distance: 30.00

Prepare

To confirm the above selection, click on the button


Apply
Fig. 4.3

Geometry generator: Prepare page

56

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

The part boundary of the remaining tool geometry (without binder)


is shown as a blue line in the main display.
Fig. 4.4

Representation of the part boundary


User interface

Model > Input generator ... > Simulation type: OneStep > OK
AFOS Input generator
Geometry > Type > Full tool (1-Step)
The predefined OS boundary has to be deleted.
Delete > Autoform - Question: Delete the current OS boundary
line? > Delete
Tool
The surfaces saved in the Part and the Binder registers are used to
automatically define the tool geometry.
Definition of the OS boundary
This line represents the outer edge of the stamped part. Again, this
may be defined as dependent upon the punch opening line.
Dependent ... > Bndry (Pre) 1 > OK > Edit > Curve editor > Global mod > Expand: 40 > OK

57

Lesson 4: Full tool (1-Step) Simulation


Definition of the OS punch opening
The punch opening line may be defined as dependent upon as part
boundary.
Dependent ... > Bndry (Pre) 1 > OK
Fig. 4.5

AFOS Input generator: Geometry page

58

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Fig. 4.6

OS boundary and OS punch opening


Blank

Define the sheet thickness:


Thickness: 1.0
Select the following material:
Material: Import... > Steel_General+Europe: if18_1.mat > OK
Define the weld line now:
Add weld... > Weld line > Input ...

59

Lesson 4: Full tool (1-Step) Simulation


Fig. 4.7

Weld dialog
The Curve editor is opened. Define the weld line by entering two
points (x = 0/0, y = 200/-200). The start and end point of the weld line
are positioned on the OS boundary.
Note:
Note To create a vertical line, press the Shift key when setting the
end point of the weld line.
Fig. 4.8

Definition of the weld line position


Following the definition of the weld line, specify a new sheet thickness value, and then select the side of the defined weld line where
the new thickness value applies (Weld dialog):
Thickness: 1.5
Properties apply at > Click
60

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Fig. 4.9

Definition of area in the sheet with changed material properties


Using the right mouse button, click at the right side of the weld line
to which the new thickness will apply.
Finalize the weld line definition in the Weld dialog by clicking on
OK
Lube

Lubrication > Constant > Constant > Standard: 0.15

Process

As you are preparing a Full tool OneStep simulation, it makes sense


to define a binder pressure or binder force.
Holding condition > Type: > Binder pressure > Pressure: 6 >
Binder stiffness: 50

61

Lesson 4: Full tool (1-Step) Simulation


Fig. 4.10

Process page
Leave the default settings on the Control page unchanged and start
the simulation in the AFOS input generator.
Job > Start simulation ... > Save > Start job: Start
After simulation is completed, the results may be viewed and evaluated in the AutoFormUser Interface by reopening the simulation
file:
File > Reopen

62

User interface

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Select the result variable Thickness.

Fig. 4.11

Distribution of thickness

63

Lesson 4: Full tool (1-Step) Simulation


Click on the button for the developed blank

:
Fig. 4.12

Developed blank
You realize that the original linear weld line has moved during the
forming process. It is the objective now to keep the weld line position as it is and to optimize the weld line position in such a way that
the original blank can be formed with a linear weld line.
To achieve the objective, define material marks at both ends of the
weld line on the developed blank.
Results > Material marks ... > Set marks

64

User interface

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Fig. 4.13

Coordinates of the material marks


Define the two material marks as material line. Internally additional
material marks are added along the material line.
AutoForm - Material marks > Define > Material line
Click on the button Formed Sheet in the lower left area of the AutoFormUser Interface and display the originally defined weld line.
Display > Lines ... > Weld 1 > Dismiss
You can judge from the material lines if the warped position within
the part is still acceptable and if the weld line is still in the correct
position.

65

Lesson 4: Full tool (1-Step) Simulation


Fig. 4.14

Different weld line positions


Use the material line on the formed part as weld line for another
simulation. For this purpose export the material line:
Results > Material lines ... > Material line 1 > File > Write selected
to file > AF Poly3D > CLOSED polylines: No > weldnew.af >
OK > Material lines > File > Dismiss

User interface

Save the simulation under another name:


File > Save as > os_lesson_4b.sim > OK
Open the AFOS Input generator again.
Model > Input generator ...
Edit the weld line position on the Blank page by importing the
stored material line as new weld line.
Symmetry-planes/welds/holes > Edit ... > Import ... > Delete > Format: af > OK > weldnew.af > OK > curve 1 > OK > OK

66

User interface

www.forum.alghaform.com

Lesson 4: Full tool (1-Step) Simulation

Start the simulation and check whether a linear weld line is available in the developed blank.
Fig. 4.15

Optimized weld line on the developed blank

67

Lesson 5: Full tool (2-step) Simulation

4. 5 Lesson 5: Full tool (2-step) Simulation


This lesson is based on a prepared simulation file. The tool contained in this file has
been generated with AutoFormDieDesigner. Objective of this lesson is the definition of
symmetry conditions and drawbeads. In addition, we will also show how to optimize
the initial blank.
Fig. 5.1

Tool geometry

Opening the prepared Simulation File


Open the prepared simulation file in the AutoFormUser Interface:
File > Open ... > Select a file: os_lesson_05.sim > OK
The AFOS input generator is opened automatically. Because the
Geometry page is shown in red, you have to enter more information on the Geometry page. The following settings have already
been defined: Full tool (2-step) simulation with tools and binder
surface. Define the OS boundary by importing an existing line in
AutoForm format (.af).

68

www.forum.alghaform.com

Lesson 5: Full tool (2-step) Simulation

Fig. 5.2

AFOS Input generator: Geometry page


Geometry

Import OS boundary
OS boundary > Import ... > Format: af > Vertices: use all rotate >
OK > Select a file: osboundary05.af > OK > Select curve: Curve 1 >
OK
Define the OS punch opening line now. This line is defined as
dependent on the punch opening line as specified in the DieDesigner tool geometry.

Geometry

OS punch opening
OS punch opening > Dependent ... > Select curve: Punch opening
1 > OK

Symmetry
Define the symmetryplane on the Blank page. The sheet thickness
and the material properties have already been specified.

69

Lesson 5: Full tool (2-step) Simulation


Symmetry-planes/welds/holes: Add symmetry ... > Symmetryplane: Click segment > User interface: Click the OS boundary at
the symmetry-plane > Symmetry-plane: OK

Blank

Fig. 5.3

Symmetry plane

Defining Drawbeads
Drawbeads may be modeled in AutoForm using a force factor to
control metal flow, without having to build the detailed drawbead
geometry into the CAD model of the tool. This gives the user flexibility in using AutoForm as a tryout tool using it to quickly compare the performance of different drawbeads visavis feasibility
requirements, and to identify the best bead configuration, based on
comparisons, without having to modify tool geometry to accomplish the same.
AFOS input generator
Add > Drawbead > Add drawbead: Use default settings > Add
drawbead
A Drawbead (Drwbds) page is added to the AFOS input generator.
Define the position of the drawbead:

70

www.forum.alghaform.com

Lesson 5: Full tool (2-step) Simulation

Fig. 5.4

AFOS Input generator: Drawbead page


Drwbds

Drawbead line > Input ... > Curve editor


Move the mouse cursor into the main display. Using the right
mouse button, click three points on the geometry to create the
drawbead (see Fig. 5.5). End input of the drawbead by double click
and finally close the Curve editor by clicking
Curve editor > OK

71

Lesson 5: Full tool (2-step) Simulation


Fig. 5.5

Position of the drawbead


Functions for generating a drawbead:
Name: Name of a drawbead can be specified.
Input ...: Position of drawbead line can be specified (Curve
editor).
Import ...: Drawbead line is imported from CAD.
Copy from ...: Drawbead line is copied from an existing
line. Base line and drawbead line are treated as different
lines.
Dependent ...: Drawbead line is created from an existing
line. Drawbead line is a reference to the base line. This
means only the base line can be changed and the dependent drawbead line will also change correspondingly.
Position: Displacement of drawbead line in xy plane
Width: Width of a drawbead
Forcefactor: Force factor of a drawbead
Usage tip Curve editor
A curve closed or open may be created using the Curve editor by
adding control points (or nodes). Each new control point creates a
new curve segment running from the last point to the new one.
Curve segments may be linear or curved. It is possible to toggle
between two types of segments using the Ctrl key. Holding the Ctrl
key down while creating a point with the right mouse button creates a linear segment.
72

www.forum.alghaform.com

Lesson 5: Full tool (2-step) Simulation

Using just the right mouse button would create a curved segment. It
is possible to switch the mode of an existing segment between
curved and linear modes by holding the Ctrl key down while clicking (anywhere) on the segment with the right mouse button.
Starting the Simulation
Job > Start simulation ... > Start job: Start
After simulation is completed, the results may be viewed and evaluated in the AutoFormUser Interface by reopening the simulation
file:
User interface

File > Reopen


The simulation results are shown by the result variable Formability
in Fig. 5.6.

Fig. 5.6

Simulation results

73

Lesson 5: Full tool (2-step) Simulation


The initial blank will be optimized now, i.e. as a result a rectangular
or trapezoidal blank will be determined. Click the button Developed blank.
Process > Process stage: Developed blank

User interface

The initial blank as calculated on the basis of the OS boundary is


shown. Generate a trapezoidal blank on the initial blank using
material marks. These material marks are completely connected to
the blank and will be defined as a material line.
Results > Material marks ... > AutoForm - Material marks: Set
marks
Fig. 5.7

Position of the material marks


Having defined four points on the blank, define these points as
material line.

74

www.forum.alghaform.com

Lesson 5: Full tool (2-step) Simulation

Fig. 5.8

Coordinates of the material marks


AutoForm - Material marks > Define > Material line
Activate the process stage containing the actual results of the
OneStep simulation.
Process > Process stage: Formed sheet

75

Lesson 5: Full tool (2-step) Simulation


Fig. 5.9

Material line at process stage Formed sheet


The material line defined above is now shown on the decklid geometry. Use this line as OS boundary for another Full tool (2-step) simulation. For this export the material line in the process stage Formed
sheet:
Results > Material lines ... > AutoForm - Material lines: Material
line 1 > File > Write selected to file ... > AF Poly3D > Should the
data written as CLOSED polylines: Yes > Select a file: Selection:
osboundarynew.af > OK
Save the simulation under another name. A new simulation file is
set up, containing the input data of the existing simulation file.
File > Save as ... > Save as: Selection: os_lesson_05b.sim > OK
Open the Input generator and go to the Geometry page:
Model > Input generator ... > Geometry

76

User interface

www.forum.alghaform.com

Lesson 5: Full tool (2-step) Simulation

Import the new OS boundary now:


OS boundary: Import ... > AutoForm - Question: Delete the current os boundary? Delete > AutoForm - Question: Delete currently
defined symmetry plane(s)? Delete > Import line(s): Format: af >
OK
Select a file: osboundarynew.af > OK > Select curve: Pick or select
from list: Curve 1 > OK
Attention:
Attention The existing symmetryplane has been deleted by the
import of the new OS boundary. Go to the Blank page of the Input
generator and redefine the symmetryplane.
Start the new simulation and check both the forming results and the
shape of the initial blank.
Fig. 5.10

Optimized trapezoid blank

77

Lesson 6: Optimization

4. 6 Lesson 6: Optimization
This lesson describes in a simple example how process parameters can be automatically optimized using the optimization algorithm of AutoForm. Process parameters in
OneStep can be the restraining forces at the part boundary.
Fig. 6.1

Geometry of optimization example


AutoForm offers an optimization algorithm that is fully integrated
into the user interface. It allows the user to optimize various input
parameters, so that a robust and highquality part can be produced
consistently. Optimization criteria can be defined by the user by
using the different FLD zones. In most cases, the criteria will be
used to produce a part without any cracks/splits and wrinkles, and
having a uniform thickness strain (e.g. 2%) in all areas. Input
parameters, which are available for an optimization can be binder
forces, drawbead force factors, blank size or tool geometry (using
AutoFormDieDesigner). For all these optimization parameters, the
user defines (a) the parameters and (b) the allowable minimum and
maximum values of these parameters. Selected optimization parameters are marked in the Input and Geometry generator in yellow
(highlighted).
Parameter studies are also possible with AutoFormOptimizer.
Input parameters can be automatically varied and the result variations can be analyzed to determine the process sensitivity and
dependence on the parameters. The goal is to find the dependency
of the results of the drawing process on the parameters and to
determine a process window.
In the following example an optimization of restraining forces at the
part boundary is defined which is based on a completed OneStep
simulation.

78

Lesson 6: Optimization

www.forum.alghaform.com

Open the simulation file os_lesson_06_basis.sim:


File > Open > os_lesson_06_basis.sim > OK
Create an optimization:
Model > Input generator > Create > Optimization
First the design variables have to be defined, which will automatically be varied by the optimization algorithm, to achieve better part
quality. The restraining forces on the part boundary (Restraining
Constant) will be optimized. Proceed as follows:
Process

Restraining > Constant


Click with the right mouse button the yellow framed input field of
the restraining force. A menu titled Add/edit design variable will
open (Fig. 6.2).

Fig. 6.2

Menu to define design variable


Name: Name of the design variable
Dependent: Name of a previously defined design variable:
This defines a dependent design variable, which means the
value of this parameter depends on the previous one.
Independent: Definition of a fully independent design
variable
Start: Starting value of design variable to use
Min: Minimum allowable value of design variable
Max: Maximum allowable value of design variable
The optimization range of restraining force is between a free part
boundary (Forcefactor = 0.0) and a fixed or fully locked part bound-

79

Lesson 6: Optimization
ary (Forcefactor = 2.0). The start value for the restraining force is a
free part boundary (Forcefactor = 0.0).
Complete the input for force factor of the first restraining force
(design variable) by using the submenu titled Design variable
definition of the menu Add/edit design variable as follows:
Name: rest > Dependent: Independent > Start: 0 > Min: 0 > Max: 2
(Fig. 6.2) > OK
Now the background color of input field has changed to yellow.
This means the parameter is to be used as a design variable. The
name of this variable is displayed in the input field (Fig. 6.3).
Fig. 6.3

Menu to define restraining forces


Restraining > Constant > The design variable rest (force factor) is
defined
All design variables have been defined now. Complete the input on
Optimize page of Input generator. Switch to this page (Fig. 6.4).

80

Process

www.forum.alghaform.com

Lesson 6: Optimization

Fig. 6.4

Optimize Design v. page of Input generator


Design variables

Optimization/Parameter study: Definition of optimization


or parameter study
Optimization: Optimization will be performed.
Normal random: Parameter study; variables will have a
Gaussian distribution around a defined center in parameter range.
Uniform random: Parameter study; variables will have an
arbitrary distribution in parameter range.
Regular grid: Parameter study; variables will have a regular distribution in parameter range with a specified number of calculations.
Name: Name of design variable
Current: Current value of design variable for the opened
simulation file
Start: Start value of design variable
Min: Minimum value of design variable
Max: Maximum value of design variable
Switch to subpage Optimize Control (Fig. 6.5)

81

Lesson 6: Optimization
Fig. 6.5

Optimize Control page of the Input generator


Maximum number of simulations: Maximum number of
simulations for an optimization or parameter study. The
study will be stopped if the maximum number of iterations
is reached
Accuracy: If variation of target function is smaller than the
Accuracy value. Optimization/parameter study will be
stopped (convergence has been reached).

Iteration control

All: All simulations are stored on disk (Warning: This


requires a large amount of disk space).
Series of best: The next best simulation is always stored on
disk.
Only best: Only the best simulation is stored on disk.
None: No simulation is stored on disk.

Keep simulations

User can specify a list of computers which can be used for optimization/parameter study:
Name: Name of computer

82

Hosts

www.forum.alghaform.com

Lesson 6: Optimization
Directory: Directory in which simulations can be stored
temporarily
#Lic: Number of AutoForm licenses on computer
#Jobs: Number of jobs, which can run in parallel
Use: Use or do not use this computer for this optimization/
parameter study.
Add host : Specify a new computer for optimization/
parameter study.
Edit host : Edit computer parameters for optimization/
parameter study.
Save hosts: Save specified parameters of computers.

No inputs are necessary on Control page for this example. By


default, the local computer is selected and activated for usage for
optimization/parameter study. The directory in which simulations
are stored is the directory from which the AutoFormUser Interface
was launched or from which the simulation file was opened. Click
on the host name on Control page. Now open the menu named
Add/edit hosts by clicking the button Edit host ... (Fig. 6.6)
Fig. 6.6

Add/edit host menu on Control page of optimizer


Host definition

Hostname: Name of computers


Get possible executables from host: Search for available
AutoForm solvers. Solvers are displayed in the Incremental and Onestep fields.
Working directory: Directory in which the simulation file
is stored
Remote shell: Type of shell

83

Lesson 6: Optimization

Remote copy: Remote copy command


Names of executables: Names of AutoForm solvers
Incremental: AutoFormIncremental solver
# Incremental licenses: Number of AutoFormIncremental
solver licenses
Onestep: AutoFormOnestep solver
# Onestep licenses: Number of AutoFormOnestep solver
licenses
OK: OK
Cancel: Cancel

Close this menu using Cancel. Switch to the Target page (Fig. 6.7).
The target function is defined as follows:
For the whole part including the fill areas, the major strain
must be 20% below the Forming Limit Curve (FLC).
Thinning is limited to 30% and thickening is limited to 2%.
All other target values Wrinkles and Desired strain should be
deactivated (Fig. 6.7).

84

Optimize

Lesson 6: Optimization

www.forum.alghaform.com

Fig. 6.7

Target page of Optimizer


Cracks Limit % FLC: Target area Percentage above (+)
or below (-) the FLD
Excessive thinning Acceptable thinning: Maximum
acceptable thinning
Wrinkles Acceptable thickening: Maximum acceptable
thickening for wrinkles
Insuff. Stretching Required thinning: Required thinning
Desired strain Desired major=minor strain: Desired
plastic strain
Save the optimization input in file os_lesson_06.opt using the following options:
File > Save as > os_lesson_06.opt > OK
Start the optimization using:
Run > Start Optimization > Program: afopt_3.1 > Start (Fig. 6.8)

85

Lesson 6: Optimization
Fig. 6.8

Optimization manager page

86

Save as plain simulation : Save as simulation without


optimization.
Fork to new optimization ...: Save as a base simulation file
for new optimization.
Delete simulations : Delete the stored simulation files
(userselected).
Strip optimization: Delete all simulation files except base
simulation file.

File

Program: Choice of optimizer version


Start: Start optimization
Open sim.: Opens a stored simulation file from an optimization run.
Base: Choice of stored simulation files from an optimization run
Convergence : Display of convergence of the optimization run.
Delete sim : Delete stored simulation files (user
selected).
Dismiss: Close the Optimization manager menu.

Buttons

www.forum.alghaform.com

Lesson 6: Optimization

Analyze optimization results


When all simulations of the optimization run have been successfully completed, open the simulation file using:
File > Open optimization > os_lesson_06.opt > OK
First open the menu titled Start/manage optimization ... using:
Run > Start/manage optimization ... (Fig. 6.9)
Fig. 6.9

Optimization manager page is opened when optimization run is


completed
Use the Convergence ... menu to get a first overview about the
number of simulations, behavior of convergence, and the best simulation result. Open the Convergence ... menu using:
Run > Start/manage optimization ... > Convergence ...
The target function value is displayed over the number of simulations (Fig. 6.10).

87

Lesson 6: Optimization
Fig. 6.10

Menu Convergence with activated option Target


Stored simulations are marked with a bullet, and the best simulation (55th) with a rectangle. Switch to option All criteria (Fig. 6.11).
The target function is now divided into single criteria, displayed
over the number of simulations in the optimization run. The different criteria of the target function are:
Wrinkles/Insufficient stretching
Desired strain
Cracks/Excessive thinning
It can be seen that cracks are the reason for peaks in the target function (Fig. 6.11).

88

www.forum.alghaform.com

Lesson 6: Optimization

Fig. 6.11

Menu Convergence with activated option All criteria


Switch to the option Log(Target) (Fig. 6.12). The target function
value is now displayed in logarithmic form over the number of simulations in the optimization run. The logarithmic representation
makes sense because the representation is more concise
Fig. 6.12

Menu Convergence with activated option Log(target)


Open the first simulation of optimization using:
Run > Start/manage optimization ... > Open sim.: 1 > Yes (Fig. 6.13)

89

Lesson 6: Optimization
Fig. 6.13

Optimization manager page with simulation 1 open


Use Ctrl E to go to the simulation end and switch on the Formability result variable. It can be seen that insufficient stretching
occurs in large areas of the part.
Fig. 6.14

Simulation 1 of optimization run with result variable Formability


Get the current value of the restraining force (Fig. 6.15).
Model > Input generator > Optimize > Design v.

90

www.forum.alghaform.com

Lesson 6: Optimization

Fig. 6.15

Input generator Optimize Design v. page with current value of


design variable rest from simulation 1
Now open the best (# 55) simulation of optimization run using:
Run > Start/manage optimization ... > Open sim.: 55 > Yes (Fig.
6.16)

91

Lesson 6: Optimization
Fig. 6.16

Optimization manager page with simulation number 55 open


Use Ctrl E to go to simulation end and switch on result variable
Formability. It can be seen that the part is much more uniformly
stretched.
Fig. 6.17

Simulation 55 of optimization run with result variable Formability


Get the current value of restraining force (Fig. 6.18).
Model > Input generator > Optimize > Design v.

92

www.forum.alghaform.com

Lesson 6: Optimization

Fig. 6.18

Input generator Optimize Design v. page with current value of


design variable rest of simulation 55

Quit User Interface


Quit the user interface using
File > Quit or use hotkey Ctrl Q.

93

Lesson 6: Optimization

ALGHAFORM TASARIM BUROSU


www.alghaform.com

www.forum.alghaform.com

94

You might also like