Professional Documents
Culture Documents
1 de 5
http://www.linnbenton.edu/auto/perform/fuel_info.html
Lean Mixtures
Adding propane to the air intake while the engine is cranking can quickly identify a no-start
engine caused by a fuel system that is too lean. Should the engine start, or almost start, when
adding propane you confirm that a lean mixture is causing the non-starting engine.
An exhaust gas analyzer will also identify a lean mixture as the cause for a no-start. Fewer
than 10,000 ppm HC in the exhaust while cranking will indicate the engine does not have
enough fuel to start. (You must study exhaust gas analysis to understand this last statement)
The most common reason for a lean mixture is not enough fuel. An empty fuel tank
will obviously cause the engine to not start. You may also have a fuel pump or fuel injectors
that fail to turn on. There are a few easy tests to check for the cause of this type of lean
condition.
You can add one gallon of fuel to see if the vehicle was out of gas.
(Remember the fuel gauge may not always be accurate).
You can listen for the operation of the fuel pump at the fuel tank.
Stick a funnel into the fuel filler neck to help you hear the pump run.
Fuel pumps should run for just a few seconds when the key is first turned to RUN.
You can hear the fuel injectors click when they turn ON and OFF.
Use a stethoscope placed on the injector while cranking the engine.
2 de 5
http://www.linnbenton.edu/auto/perform/fuel_info.html
Fuel supply system must deliver fuel to the injectors at the proper pressure with enough
volume to maintain pressure when the injectors open. The gas tank, fuel pump (usually found
in the gas tank), fuel filter, fuel pressure regulator and fuel lines are all part of the fuel supply
system.
You may have a fuel pump that runs but cannot supply the proper pressure or volume for
the fuel injectors to deliver the stoichiometric air/fuel ratio.
The fuel pump can be fine however the pressure regulator may malfunction and supply too
little fuel.
Any restriction in the fuel supply line, including the fuel filter, will also cause low fuel
volume. A fuel filter is the most common reason for a restricted fuel supply as it gets plugged
if it is too old, or the fuel gets contaminated.
The best way to check the fuel supply system is with a fuel pressure - volume test.
Another reason for a lean mixture is Too Much Air. The stoichiometric air/fuel ratio is
maintained by computer sensors. A leak in the intake manifold or air ducts may let air into the
cylinders that is not recorded by the Powertrain Control Module (PCM). If air gets into the
engine that the computer does not measure the engine will run lean. Systems that use a Mass
Airflow Sensor(MAF) or a Vane Airflow Sensor(VAF) rely upon an air intake system with no air
leaks. On systems that use an airflow sensor, any air intake leak will cause a lean mixture.
You can check for air intake leaks using a smoke machine.
3 de 5
http://www.linnbenton.edu/auto/perform/fuel_info.html
4 de 5
http://www.linnbenton.edu/auto/perform/fuel_info.html
Remember to carefully check for leaks after removing the pressure gauge and turning the
fuel pump back ON. Use a good flashlight or fluorescent light to look at every connection you
disturbed including the Schrader valve. Always replace the cap on the Schrader valve. If it was
missing, use a tire valve stem cap.
Fuel Injectors
Fuel injectors that fail to turn ON
will prevent fuel from entering the intake
manifold. Fuel injectors are simple
solenoids that allow fuel to spray into the
intake manifold when they are turned on.
As they turn On and OFF they will
make a clicking noise. Using a
stethoscope you will hear this click. If
they do not click, they are either stuck, or
they are not getting the proper electrical
signal. A noid light can verify if the
injectors are getting the signal to turn On
and Off. The best way to check the
electrical signal to fuel injectors is to use a
lab scope.
Rich Mixtures
A fuel system that is too rich can also
cause the engine to not start. A plugged
air filter, a fuel pressure regulator that is
leaking, leaking injectors, fuel pressure
that is too high, or a fuel control sensor
sending the wrong information to the PCM can cause a rich air/fuel ratio.
Plugged air filters are easy to check, need frequent replacement, and are often overlooked
when trying to figure out why an engine is too rich. As an air filter becomes clogged the fuel
control sensors will sense that less air is entering the system and should reduce the amount of
fuel to match. This will result in a gradual loss of power that may not be noticed by the
customer. Once in a while an air filter will become so dirty that not enough air can get in to
start the engine. Also it is not uncommon for high mileage engines to have excessive oil in the
air filter housing. This can be caused by defects in the PCV (Positive Crankcase Ventilation)
system, or by an engine with worn piston rings allowing crankcase pressure to force oil into the
air cleaner. If the air filter is plugged by oil you should diagnose why the oil is in the air filter
housing. Merely replacing the air filter will be a very temporary fix.
Many systems use a fuel pressure regulator that is mounted on the fuel rail. For Port fuel
injection these pressure regulators will have a vacuum line attached to balance the pressure in
the fuel line with the intake manifold pressure. By removing this vacuum hose you can check
for gasoline that is leaking into the vacuum line. Any gasoline in this vacuum hose means the
pressure regulator is leaking and should be replaced. Also if this vacuum line is worn out or
disconnected it will cause the fuel pressure to be too high, and a rich mixture will be the result.
When a fuel injector is turned off, it should not allow fuel to flow into the intake. A fuel
pressure test can help you find leaking fuel injectors.
5 de 5
http://www.linnbenton.edu/auto/perform/fuel_info.html
Any one fuel injector can fail however all fuel injectors tend to slowly flow less fuel as they
become restricted by varnish and contamination in the fuel. If you replace just one fuel
injector, it will now flow more fuel than the other injectors and a rough running engine can
result. It is recommended that if any one injector is defective, the entire set of injectors should
be replaced as a matched set. New injectors can be very expensive. There are businesses that
specialize in fuel injector service and will recondition fuel injectors for cheaper than
replacement. Another advantage to this service is that they will flow-test the injectors and send
you a matched set. Be sure that the injector reconditioning service uses an ultrasonic cleaning
system, and flow-tests each injector to ensure the returned injectors have equal flow rates.
On-Car injector cleaning is an excellent preventative maintenance procedure. Cleaning the
injectors, the fuel rail and the air intake system can improve fuel economy and return an engine
to a smoother, cleaner, more efficient performance. Many inexpensive fuel cleaning systems are
available however systems that are not capable of cleaning the fuel rail and "back flushing" the
fuel injectors are not effective.
Fuel pressure that is too high can cause an engine to run rich, or not start. A fuel pressure
test is the only way to verify that the fuel pressure is correct. Be sure to carefully look up this
specification, as it will change depending upon the year, make, model, and engine size.
Computer Controls
The PCM must get the correct information from it's sensors to know how long to turn on
the fuel injectors. Checking codes and data to the PCM using a scan tool can help identify
which sensor may be sending the wrong information. Being able to effectively use the scan
tool takes careful study and practice. The more you use it, the easier it gets.