Professional Documents
Culture Documents
CABINET DOOR TV
USER MANUAL
Sky eye
www.luxurite.com
Contents
WARNINGS AND CAUTIONS 01
Safety instructions 05
Components 09
Introduction Introduction 09
Installation 15
Main Operation 24
General Operation Connection 25
Trouble shooting 49
Technical specifications 53
Excursus Declaration and Notes
for PC part of the Cabinet Door TV 55
WARNINGS AND CAUTIONS
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ENCLOSURE.
NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
Thank you for choosing LUXURITE Cabinet Door TV.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
Before using t his product please read the instruction manual carefully of uninsulated dangerous volta ge within the products enclosure that may be of sufficient magnitude to constitute
whic h will ensure correct installation and ease of use. Plea se keep this a risk of electric shock to persons.
operating and maintenance (servicing )instructions in the literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
This is an All-in-One machine of TV and PC,with independent switch, DO NOT OPEN
REGULATORY INFORMATION
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
It will increase the machine`s heat if turning on the TV power and PC power
accordance with the i nstruction s, may cause harmful interference to radio communication.However, there
48 simultaneously.For the better maintenance of the machine,please do not turn on
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
TV power and PC power more than 48 hours at one time.
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on. The user encouraged to try to correct the interference by one or more of the
following measures:
Relocate the receiving antenna.
The PC equipped with standard 8G solid state Disk space should be deleted the Increase the separation between the equipment and receiver.
8G unnecessary files to ensure the normal operation of the PC system. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Contact the dealer or experienced radio/TV technician for help.
The build in wireless network adapter can be linked to the network Any changes or modifications not expressly approved by the party responsible for
without cable. compliance could void the user s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without authorization from supplier.
Unauthorized modification could void the user s authority to operate this product.
2
WARNING WARNING
TV door receiver. Do not remove the cabinet mains socket with protective earthing.
back from the set. Refer servicing to qualified
service personnel.
CAUTION
CAUTION
WARNING
Do not place your TV door on an unstable cabinet.
Do not drop or push objects into the TV door
Failure to follow these instructions may result in
cabinet slots or openings. Never spill any
serious injury to individual or damageto TV door.
kind of liquid on the TV door receiver.
CAUTION
WARNING
LU
CaXU
RIT
bin
etETV
Do
or When the TV door receiver is not used for an
Excessive sound pressure from earphones
extended period of time, it is advisable to
and headphones can cause hearing loss.
disconnect the AC power cord from the AC outlet.
CAUTION
CAUTION
Do not block the ventilation holes in the back
Avoid exposing the TV door receiver to direct
cover. Adequate ventilation is essential to prevent
sunlight and other sources of heat. Do not install
failure of electrical components.
the TV door receiver directly on other products
LU
XD
Ca
bi
etnRI
UEoTV
or T
which give off heat, e.g.video cassette players and
CAUTION audio amplifiers. Do not place naked flame
sources, such as lighted candles on the television.
Do not trap the power supply cord under the
TV door receiver.
3 4
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
1.Read these safety instructions.
Only use with power supply provided. LUXURITE
Cabinet Door TV
2.Keep these safety instructions.
3.Heed all warnings.
4.Where the mains plug or an appliance coupler is used as
WARNING
the disconnect device,the disconnect device shall remain
The luxurite system components should be readily operable.
mounted in a dry location away from heat 5.Follow all safety instructions.
sources,i.e. away from heat/flame/steam/moisture. 6.Do not use this apparatus near water.
7.Clean only with dry cloth.
5 6
Note
If the TV is under cold condition, there may be a small flicker when you turn it on.
Avoid touching the LCD screen or holding your finger(s) against it.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury
Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Introduction
7
Components
Ensure that the following components are attached with your TV. If any accessory is missing, please
contact the dealer where you purchased the product.
TV door
LCD display
screen Remote sensor
Power Lead + Adaptor Remote control User manual
Media Box
Rear Panel
Control Panel
Media Box TV door Keyboard and mouse
9 10
Control Panel Rear Panel
1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 5 6 7 8 9 10 11 12 13 14 15
ITEM ITEM NAME / SYMBOL FUNCTION DESCRIPTION ITEM ITEM NAME / SYMBOL FUNCTION DESCRIPTION
The red-difference chroma components
1 POWER INDICATOR Red/Green light indicates LCD TV is at standby/working mode; 1 Pr/Cr
The blue-difference chroma components
2 Turn on/off the LCD TV 2 Pb/Cb
11 12
Flank Panel
1 2 3
2 USB port
3 SKY EYE
Connect SKY EYE
For LUXURITE SKY EYE only Installation
13
All electrical work should be undertaken by a suitably qualified person.
Screw
Door hinges
Screw TV DOOR
Cabinet TV DOOR
2. Fit door to cabinet as per standard 4. Fit media hub to cabinet (screwing)
15 16
DVD
TV
5.Connect cable from door to media box. 7.Connect TV aerial or set box to aerial or scart connector on media hub.
17 18
Remote Control Key Functions
There might be some differences from your actual unit.
EJECT
STANDBY AUTO
MUTE
STANDBY
Switch on LCD TV at stand by mode or vice
1 2 3 versa.
4 5 6 EJECT/AUTO
Eject the DVD in DVD mode;
7 8 9
Auto configuration directly in PC source.
-/-- 0
ASPECT NICAM MUTE
Press to mute the sound.Press again or press
VOL+ to unmute.
DISPLAY
0-9
ENTER Press 0-9 to select a TV channel directly when you
LCD are watching TV. The channel change after 2 seco-
MENU EXIT
CH+/-
Press to scan through or to select a channel.
VOL+/-
Press to increase/decrease the sound level.
ASPECT
To select the aspect of screen.eg.: 16:9 14:9
zoom auto 4:3 ;
NICAM
Press to select the NICAM modes.
DISPLAY
Press to display the source and channel`s information.
20
/ / / /ENTER
Allows you to navigate the on-screen menus and
adjust the system settings to your preference.
EJECT EJECT
STANDBY AUTO
MUTE STANDBY AUTO
MUTE
2 LCD MENU 2
1 3 1 3
Brings up the LCD main menu to the screen in an-
4 5 6 alogue TV mode. 4 5 6
7 8 9 7 8 9
EXIT
-/-- 0 To exit menu or submenu.
-/-- 0
ASPECT NICAM ASPECT NICAM
DISPLAY DISPLAY
INPUT
Press to cycle through the input source.
ENTER ENTER
PMODE
LCD DVD
MENU SETUP Press repeatedly to cycle through the available video LCD
MENU
DVD
SETUP TEXT
picture modes Switch On or Off the teletext mode;
EXIT EXIT
INPUT PMODE SMODE SLEEP INPUT PMODE SMODE SLEEP
HOLD
SMODE
Hold On or Off for current page display;
FAV FAV- FAV+ EPG Press to cycle through the different sound settings. FAV FAV- FAV+ EPG
LANG
TEXT HOLD LANG SUBTITLE
SLEEP TEXT HOLD LANG SUBTITLE To show the list of audio languages available for the
Current channel. Just in DVB mode;
INDEX SiZE REVEAL SUBPAGE
Let you select a mount of time before your TV turn INDEX SiZE REVEAL SUBPAGE
itself off automatically. SUBTITLE
To switch the dialogue at the bottom of the screen.
INDEX
Request the index page;
FAV
Press to display FAV menu in DVB mode; SIZE
Change display size in teletext mode;
FAV-
REVEAL/ANGLE
DVB source decrease fav channel;
Reveal or hidden the hidden words;
FAV+ SUBPAGE
DVB source increase fav channel; Sub coded page access;
EPG
Press to show the Electronic Program Guide menu.
21 22
Main Operation
TURN ON LCD TV
1. Connect the AC power adapter cable to TV, At this time the TV will enterstandby into mode
and the indicator will switch to red as standby mode
2. Press STANDBY button on the TV set or button on the remote control to turn on LCD
TV. Indicator will switch to green as working mode.
PC:
General Operation Turn on PC button on the media box and press Input key on the remote control,
Choose PC mode. In this mode, the TV DOOR can be used as a normal computer with enclosed
wireless keyboard and mouse. Please consult your supplier for specific features such as operating
system, computer configuration.
Please keep PC off when you do not use computer function to save power and PC life.
In the PC mode, the LAN jack and USB port can be used as in normal computers. And the
VGA socket can be used for media box PC's RGB signal output.Please consult computer
professionals if you have any enquiries.
TV
SCART
cvbs
S-VIDEO
PC
HDMI
DTV
24
CONNECTION AUDIO cable
R
1. Connect the TV
Make sure that LCD TV is power off AUDIO IN
Insert the TV cable into antenna socket R
Turn on the TV
CVBS cable AUDIO cable CVBS AUDIO IN
Select TV mode L
L
Control the volume by VOL- / VOL+
Using CH+/CH- to choose the channel
LCD TV can be turned off by power button on remote control
S-VIDEO S-VIDEO
cable
25 26
4. Connect to LAN and USB
In the PC mode, the LAN jack and USB port can be used as in normal computers. Please
consult computer professionals if you have any enquiries.
27
Analog Program Search
ATV
Press / button and then use / to select whether to start searching analog programs.
First Time Installation After setting the items, select OK to finish the first time installation, or select Cancel to exit
this menu.
Select Adjust
If this is the first time you open the TV and there is no programs in the TV memory, the
First Time Installation menu will appear in the picture. TV Information
Language
Press / button and then use / to select the OSD language. 4
1 25 TV Label
Delete Analog Program 2 Auto Auto 5
Press / button and then use / to select whether to delete all the analog programs. 3 No Signal 6
29 30
1. The number of current program. When you are satisfied with your adjustment, press the LCD-MENU button to return to the
2. The colour system of current program, could be selected in Manual Tuning menu (an option previous menu or press the EXIT button to exit the main menu.
of SETUP menu).
3. The name of current program. Picture Mode
4. The label of current program, you can label it in Manual Tuning menu (an option of SETUP Select Picture Mode in PICTURE menu. (Available picture mode: Standard, Personal,Movie,
menu). Sport, Mild, Game.)
5. The sound system of current program, could be selected in Manual Tuning menu (an option If you change the value of Contrast, Brightness, Colour, Tint, Sharpness or Colour temperature
of SETUP menu). on the picture menu, the picture mode will be changed to "Personal" automatically. You may
6. The NICAM mode of current program. select the picture mode directly by pressing PMODE button.
If the icon of NICAM mode is red, it means the current program supplies multi NICAM
TIPS
signals, and you can select it by pressing NICAM button.
You can press PMODE button on the remote control, to select the Picture Mode directly.
The NICAM modes and relative icons:
After adjusting the value you want, press LCD-MENU button to return to the preview MENU.
PICTURE
PictureMode Standard
Contrast 50 PICTURE
Brightness 50 Colour 50
Colour 50 Tint 0
Tint 0 Sharpness Normal
Sharpness Normal Colourtemperature Normal
DNR Off
Select Adjust
31 32
Colour Press the / button to select SOUND in the main menu.
Press / button and then use / to adjust the colour saturation. Press the / button to select the option that you want to adjust in the SOUND menu.
Press the / button to adjust.
NOTE: This option is invalid in PC mode, and it will be shown in gray. When you are satisfied with your adjustment, press the LCD-MENU button to return
to the previous menu or press the EXIT button to exit the main menu.
Tint
Volume
Press / button and then use / to adjust the tone of colour when your system is in NTSC.
Press / button and then use / to adjust the sound level.
Sharpness
Volume 28
Press / To select the sharpness mode of your TV. (Available Sharpness Mode: Normal, Sharp,
Sharpest, Softest, Soft.)
Colour temperature
Select an optimum colour temperature mode to suit your eyes for viewing among Warm After adjust the value you want, press LCD-MENU button to return to the preview MENU.
and Cold.
Sound Mode
Select Sound Mode in SOUND menu. (Available sound mode: Personal, Voice, Music, Theatre.)
NOTE: This option is available only in PC mode.
If you change the value of Bass and Treble on the Sound menu, the sound mode will be changed
to "Personal" automatically. You may select the sound mode directly by pressing SMODE button.
DNR (Digital Noise Reduction)
If the broadcasting signal received is weak, you can select the DNR option to reduce the video TIPS
noise level between Off, Low,Mid and High.
You can press SMODE button on the remote control to select the Sound Mode directly.
Press MENU button on the front panel or LCD-MENU on the remote control to display Bass
the main menu. Press / button and then use / to increase or decrease the level of the lower-pitched sounds.
Treble
Press / button and then use / to increase or decrease the level of the higher-pitched sounds.
SOUND
Volume 28
Balance
SoundMode Personal
Press / button and then use / to adjust the audio output between left and right speakers.
Bass 0
Treble 0
Balance 0
Setup menu options
Press MENU button on the front panel or LCD-MENU on the remote control to display the main
Select Adjust menu.
33 34
NOTE Auto Tuning
SETUP menus are different for different input sources, if the input source is selected
HDMI / YPbPr / VGA and there are no relative input signal, SETUP menu will be
Press ENTER key to start.
unavailable.
Auto Tuning
Searching
ATV 6 215.00MHz
SETUP MENU Exit
Country UK
Autotuning You can press LCD-MENU button to stop auto tuning and close the OSD menu.
Manualtuning
Program Edit Manual Tuning
This option allows you to perform Manual Tuning.
NOTE
Select Adjust Before you perform Manual Tuning, you must choose the country where you are
by selecting Country option.
Press the / button to select SETUP in the main menu.
Press the / bu tton to sele ct your option what you want to adjust in the SETUP menu. 1. Press / to select Manual tuning in SETUP menu.
Press the / button to adjust. 2. Press / to perform your selection, the menu of Manual tuning will display on the
When you are satisfied with your adjustment, press the LCD-MENU button to return to the screen.
previous menu or press the EXIT button to exit the main menu.
Country
This option allows you to select the country.
Manualtuning
Auto tuning
Program 23
This option allows you to tune the channels that can be received automatically.
SoundSystem DK
ColourSystem Auto
NOTE Program Lable
AFT Off
Before you perform Auto Tuning, you must choose the country where you are by selecting
ManualSearch 471.43 MHz
COUNTRY option.
Select Adjust
35 36
Program Program Edit
The current program number. Press / to select the upper or lower program. Channel List This function allows you to sort
Flags ATV the TV programs according to
Sound System
1. your preferences, as following:
Press / to select a corresponding sound system, such as DK, L/L , BG.
x 2.
Colour System
x 3.
Press / to select a corresponding colour system, such as Auto, PAL, SECAM.
x 4.
Program Label
This option allows you to label a channel. you can also relabel the programs which have x 5.
beenlabeled. x 6.
4. Press the numeric buttons to input the numbers directly or press / to select the 1. Press / to select Program Edit in SETUP menu.
letters. 2. Press / to enter into the sub menu, a channel list will display.
5. Press / to move the cursor. 3. Press / to select the channel in the list which you would like to sort.
6. Press ENTER, LCD-MENU or EXIT button to confirm and return to previous menu. 4. Press to perform your selection.
5. Press / to select the location you would like to place the channel.
AFT (Auto Fine Tune) 6. Press to perform you selection.
Due to weak signals or a wrong antenna configuratio n, some of the channels may not 7. Press LCD-MENU to return to the previous menu or press EXIT to exit.
be tuned to the best reception condition. AFT function allows you to fine tune channel
selected(the frequency of channel is around the value in Manual Search option. SETUP menu of VGA input
(for setting the PC picture
Manual Search
position):
PC Position
Manual Search - - - . - - MHz Auto Sync Begin
Phase 51
This option has two functions: Clock 50
1. Set the frequency of channel for AFT option. H Position 50
2. Press button for 3+ seconds and it will start auto tuning from this frequency. V Position 50
Position Reset
Select Adjust
37 38
SETUP menu of HDMI input (for setting the HDMI picture position): 3. Press the / button to adjust.
4. When you are satisfied with your adjustment, press the LCD-MENU button to return
to the previous menu or press the EXIT button to exit the main menu.
HDMI Position
H Position 50
V Position 50 TIMER
Select Adjust
SETUP menu of YPbPr input (for setting the YPbPr picture position): Select Adjust
Sleep Timer
Select the sleep time to put the TV in standby mode automatically. Timer can be selected
as 0min, 15min, 30min,45min,60min,75min,90min,105min,120min. Also you can select the sleep
YPbPr Position
time by pressing SLEEP button repeatedly.
H Position 50
V Position 50 OSD Timer
Position Reset You can select the time when the OSD display on the screen such as: 5Sec,10Sec,15Sec,20Sec,
25Sec,30Sec.
Timer menu options 1. Press the / button to select FUNCTION in the main menu.
2. Press the / button to select your option what you want to adjust in the FUNCTION menu.
Press MENU button on the front panel or LCD-MENU on the remote control to display
3. Press the / button to adjust.
the main menu.
4. When you are satisfied with your adjustment, press the LCD-MENU button to return
1. Press the / button to select TIMER in the main menu. to the previous menu or press the EXIT button to exit the main menu.
2. Press the / bu tton to sele ct your option what you want to adjust in the TIMER menu.
39 40
Child Lock
Press ENTER or button to
set the child lock.
FUNCTION FUNCTION
Language English Child Lock On Key Lock
Key Lock On Press ENTER or button to
Video Size Auto
set the key lock.
Bluescreen On Change PIN Code
Child Lock Change PIN Code
First Time Installation Press button to enter
Reset Change PIN Code menu.
Language
Press / to select the OSD language.
Blue screen
This option allows you to select the blue background on or off. If on, the screen
Select Adjust 0~9 Input ENTER Confirm
background will turn blue at very weak or no signal condition.
TIPS
41 42
First Time Installation Favorite List options
Press button to open the first time installation menu, and the operation of this menu
is in page 3. Press FAV button to open the Favorite List, then Press / to select the channel you want to
watch.
Reset
Press ENTER or button to reset the TV to the factory default. Favorite List
DTV
Program List
Press ENTER button to open the Channel List, then Press / to select the channel you want to
watch.
NOTE
Only the channels that you select to FAV in Program Edit Menu could be displayed
in Favorite List.
43 44
Signal Quality
Channel List
The signal quality of current
channel. Flags DTV
SETUP
Program Edit
Select Enter
This function allows you to edit
the DTV programs according to
your preferences, as following:
Channel 21
Start Search Begin Press Favorite on your remote control to label your favorite programs.
Service Found 1 Press delete to delete programs already added on Channel List.
Signal Quality 0% Press lock to lock up programs according to your preferences.
Signal Strength 0%
Frequency 474.00 MHz
Channel
The current channel number. Press / to select the upper or lower channel. Press 0~9 to Common Interface
select the channel directly.
Service Found
The services available.
45 46
EPG Menu
Use EPG button on the remote control to display the EPG menu directly as below:
GD TV Best Scapes
Trouble shooting
47
Before contacting the service technician, perform the following simple checks. If any problem
still exists, unplug the LCD TV and call for customer service.
THE CAUSES OF INTERFERE NCE
Incorporated in your TV receiver are the most up-to-date devices to eliminate interference.
Local radiation, however, can create disturbances which visibly affect your picture.
Proper installation, a good aerial is your best safe-guard against these disturbances.
PROBLEM POSSIBLE SOLUTION
RF INTERFERENCE
- Check that the main plug has been connected to a wall let. Moving ripples across the screen are caused by nearby transmitting or receiving short-wave radio
No sound and picture - Check that you have pressed the STANDBY button on the front of TV set.
- Check the picture contrast and brightness settings.
equipment.
DIATHERMY
- Check the volume.
Normal picture but - Sound muted? Press the MUTE button. Herringbone pattern and partial picture loss can result from the operation of diathermy
no sound - Try another channel ,the problem may be with the broadcast.
- Are the audio cables installed properly.
equipment From a nearby doctor's surgery or hospital.
- Check to see if there is any object between the product and remote control Causing obstruction.
The remote control - Are batteries installed with correct polarity(+ to +,- to -). SNOW
- Correct remote operating mode set: TV, VCR etc.
does not work Weak TV signals from long distant stations result in an unsteady picture and give the effect of
- Install new batteries
falling snow. An antenna adjustment or antenna amplifier may be needed.
- Is the sleep timer set.
Power is suddenly - Check the power control settings. Power interrupted.
turned off - No broadcast on station tuned with auto activated. GHOST
Multiple images caused by TV signals reflected back from surrounding buildings, hills, aircraft,
Picture appears slowly etc. is minimised by correct aerial positioning.
- This is normal, the image is muted during the product startup process. Please
after switching on contact your service center, if the picture has not appeared after five minutes.
CAR IGNITION
Nearby cars and electrical motors can cause small streaks across the picture or make the
- Adjust the color in menu option.
No or poor color or - Keep a sufficient distance between the product and the VCR. picture roll.
- Try another channel, the problem may be with the broadcast.
poor picture
- Are the VIDEO cables installed properly?
- Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or
- Check for local interference such as an electrical appliance or power tool.
picture shaking
Poor reception on - Station or cable product experiences problems. Tune to another station.
- Station signal is weak, reorient antenna to receive weaker station.
some channels
- Check for sources of possible interference.
Lines or streaks in pictures - Check the antenna (Change the direction of the antenna).
49 50
Maintenance
Early mal-functions can be prevented. Careful and regular cleaning can extend the time of
you will have your new TV.
Be sure to turn the power off and unplug the power cord before you begin any cleaning.
2.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Extended Absence
Excursus
If you expect to leave your TV dormant for a long time(such as vacation), it's a
good idea to unplug the power cord to protect against possible damage from
lightning or power surges.
51
Technical specifications computer configuratoin
LCD SIZE 10.2 , 15.4 , 17 ,19 , 22 ,
VIA C7-M
Brightness 300cd/ ,400 cd/ , 400 cd/ ,450 cd/ , 450 cd/
CPU 1.6GHz(VIA?C7-M CPU)
120(H) / 105(V), 140(H) / 120(V), 140(H) / 120(V), 128KB L2 Memory
Viewing angle
160(H) / 160(V), 178(H) / 178(V)
Memory 1GB DDR II
10.2 : 800x480 Hard Drive 8GB
15.4 : 1280x800 Keyboard With one wireless Keyboard
Resolution 17 : 1440x900 Mouse With one wireless Mouse
19 : 1440x900 One standard USB2.0 interface
22 : 1680 x1050 I/O Interface
One Lan interface
Video system PAL, SECAM, DVB-T 802.11b or 802.11 b/g W ireless Lan
System
Audio system BG, DK, I, L/L Wireless-device (With the IntelPRO/Wireless web solution of Intel CentrinoTM
Teletext 300 pages calculated techs)
Nicam/a2 YES
Modulation COFDM 2K/8K QPSK,16QAM,64QAM
Video System MPEG- MP@ML
DTV(DVB-T)
Audio System MPEG-1/2 layer 1,2,3
Basic Functions EPG,Subtitle,Teletext,(EURO),MHEG-5(UK)
Input
ATV 75 ANT.
PC DB 15 VGA Input
Amplify 2Wx2
OSD Languages English, French, German, Italian, Spanish, Portuguese.
Power suppy DC12V
consumption 42W, standby<1W.
53 54
System Maintenance
Declaration and Notes
for PC part of the Cabinet Door TV Please run system clearance for system partition partition C :
regularly to make sure the PC has enough space to run the system.
Configurations and functions Please use one key recovery to recover the PC s system to
original status when the system gets serious problems, crash and
The PC part of the Cabinet Door TV is intentionally designed for web
other un-recoverable problems.
pages explore or internet multimedia entertainment. Its settings
(main components: CPU, 1G memory, 8G solid state hard driver) is Recover procedures
not suitable for large scale software, games, long time continuous Make sure partition C: has no important files and make copies for all
important data and files.
turning on. To make sure it works well and save its life, not keep
turning it on for more than 48 hours. Restart the cabinet TV door s PC part
The system will run the recovery procedures automatically and do not
Solid state hard driver
need any other operations.
Small hard driver is to make the product works well even in a small
When the recovery finish, the computer s system reboot to the original
space. It is not suitable for save important files and data. Luxurite is
factory status automatically.
not responsible for any loss by loss of files or data in this PC part.
When you not use PC function, please make sure the PC is on off
status to save power and computer s life.
55 56
System Safety
To keep you use the PC part safely, please install anti-virus software
to make the system safe. Luxurite is not responsible for any damage
or loss caused by computer virus.
Appliance software
When you need install appliance software, please use the legal copy
and respect the copy right.
Warning:
`one key recovery` function will overwrite the system partition
C: to original system status, please use this function cautiously.
Sky eye
57
WARRANTY
CARD
PRODUCTION DATE:
SELLER:
THROUGH THE TEST OF QUALITY CONTROL DEPARTMENT IN OUR COMPANY, THE PRODUCT
HAS BEEN PROVED THAT THE FUNCTION PARA-METER HAS REACHED THE TECHNIQUE
CRITERIA. THEY ARE PERMITTED TO LEAVE FACTORY.
REPAIR INFORMATION