You are on page 1of 40

SERVICE MANUAL

TV SET
Chassis: 5P60
MODEL: CTV-55D10 TXT
CTV-55F12 TXT
CTV-55V20 TXT MkII
CTV-55N11 TXT
CTV-55Z10 TXT
CTV-55X10 TXT
CTV-37D10 TXT
CTV-37X10 TXT

Contents
Safety Notice------------------------------------------------------------------------- 2
Technical specification--------------------------------------------------------------3-4
Chassis Block Diagram ------------------------------------------------------------- 5
IC Block Diagram --------------------------------------------------------------------6-13
Transistor mark --------------------------------------------------------------------- 14
Chassis wiring diagram ------------------------------------------------------------ 15
PCB Top/Bottom layer ------------------------------------------------------------- 16-18
Service Adjustments ----------------------------------------------------------------19-25
Purity and Convergence Adjustment --------------------------------------------- 26
Control Location ---------------------------------------------------------------------27
Input and Output Terminals---------------------------------------------------------28
Operation Instructions-------------------------------------------------------------- 29-37
Mechanical Disassemblies---------------------------------------------------------38
Cabinet parts List --------------------------------------------------------------------39
Circuit Diagram-----------------------------------------------------------------------40

Safety Notice
SAFETY PRECAUTIONS
1:An isolation transformer should be connected in the power line between the receiver and
the AC line when a service is performed on the primary of the converter transformer of the
set.
2:Comply with all caution and safety-related notes provided on the cabinet back, inside the
cabinet, on the chassis or the picture tube.
3:When replacing a chassis in the cabinet, always be certain that all the protective devices
are installed properly,such as,control knobs, adjustment covers or shields, barriers,isolation resistor-capacitor networks etc.. Before returning any television to the customer,the
service technician must be sure that it is completely safe to operate without danger of
electrical shock.

X-RADIATION PRECAUTION
The primary source of X-RADIATION in television receiver is the picture tube. The picture
tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION
protection, the replacement tube must be the same type as the original including suffix
letter. Excessive high voltage may produce potentially hazardous X-RADIATION. To avoid
such hazards, the high voltage must be maintained within specified limit. Refer to this
service manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specfied limits, take necessary corrective action. Carefully follow the instructions for
+B1 volt power supply adjustment, and high voltage check to maintain the high voltage
within the specified limits.

PRODUCT SAFETY NOTICE


Product safety should be considered when a component replacement is made in any area
of a receiver. Components indicated by mark ! in the parts list and the schematic diagram
designate components in which safety can be of special significance. It is particularly
recommended that only parts designated on the parts list in this manual be used for component replacement designated by mark ! . No deviations fromresistance wattage or voltage ratings may be made for replacement items designated by mark ! .
-2-

FEATURES:
AC 90-260V 50/60Hz
M U LT I S Y S T E M : P A L B G / D K / I, S E C A M B G / D K L / L( O P T I O N ),
N T S C M ( O P T IO N )
VOLTAGE SYNTHESISED TUNING SYSTEM
200 PROGRAMS MEMORY
BLUE BACK FUNCTION
180 MINUTES SLEEP TIMER
FULL AUTO PROGRAM
TIMER ON
CLOCK ; CHILD LOCK
1 AV INPUT+1 FRONT AV+S-VIDEO INPUT
2 EURO SCART (OPTION)
1 YUV INPUT (OPTION)
1 AV (MONITOR) OUTPUT
10 PAGES TELETEXT (OPTION)
BLACK LEVEL STRETCH
NICAM/A2 STEREO(OPTION); SURROUND SOUND, AV STEREO SOUND
1 GAME,
200 YEAR CALENDER
TRUBASS (OPTION)
COMB-FILTER (OPTION)
FOUR PICTURE MODE USER,SOFT, STANDARD, RICH
FOUR SOUND MODE USER ,SPEECH ,MUSIC,THEATER

GENERAL SPECIFICATION:
1P O W E R C O N S U M P T I O N
S TA N D B Y P O W E R C O N S U M P T IO N
2RECEIVE SYSTEM
3 COLOUR SYSTEM:
4VISION INTERMEDIATE FREQUENCY
5 I N T E R - C A R R I E R F R E Q U E N C Y:

6. CHROMA IF FREQUENCY

7ANTENNA TYPE:
8 C H A N N E L S
R E C E I VI N G :

150W M A X .
5 W
D/K; I ; B/G; M
PAL / SECAM/ NTSC
38.9MHz
4 . 5 M H z (M )
5.5 MHz (B/G)
6.0 MHz (I)
6.5 MHz (D/K)
5.85 MHz (NICAM B/G,D/K)
6.55 MHz (NICAM I)
5 . 7 4 M H z( G E R M A N S T E R E O )

PAL/NTSC:

VHF-1
VHF-2
UHF

34.47/35.32 MHz

DIN TYPE 75
OHM
A 0 ; E 2-E 4 ;S 1 -S 9 C H
S10-S41; E5-E12
CH
E21-E69
CH
-3-

44.25-161.25MHz
168. 25 - 463.2 5 MHz
471.25-863.25MHz

VS TUNING
1 AV I N + 1 AV O U T ; 1 F R O N T AV I P U T ;
1 S - V I D E O I N , 1 Y U V IN ( O P T I O N ) ;
2 1 P I N S C A RT ( O P T I O N )
11AV IN/OUT SPECIFICATION Y/C IN-------Y1.00.2VP-P 75 O H M C:0.7 VP-P 75 O H M
1.0 0.2VP-P 75 O H M
----0-2V (r.m.s)
1.00.2 VP-P 75 O H M
----0-2V

(r.m.s)
: -------0.7 VP-P
YUV---------- Y1.0VP-P ; U 0.7 VP-P ; V0.7 VP-P
12OSD LANGUAGE
ENGLISH , RUSSIAN, IRANIAN, ARABIC, ITALIAN,
TURKIC, GERMAN,FRANCE
13TELETEXT LANUAGE:
PAN-EUROPEAN,CYRILLIC 2,IRANIAN,ARABIC
14AUDIO OUTPUT POWER: > 5W (1KHz, 0.5V INPUT , 10%THD)
15SAFETY AUTHENTICATION STANDARD CB/ CE
16LED INDICATORS
POWER ON
17HAND SET TYPE
HS08 HS09
18HAND SET POWER SUPLY BATTERY 3V UM-3/R6/AAx2
19COLOUR PICTURE TUBE
2538
20REMOTE CONTROL DISTANCE: 5 m
9 TUNING SYSTEM
10 AV IN/OUT

-4-

Chassis Block Diagram

-5-

Chassis Block Diagram


IC 401 ( UNIVERSAL HI-FI AUDIO PROCESSOR) TDA9859H

IC605.IC606<REGULATORS> L7800 SERIES


INPUT

REFERENCE
VOLTAGE

SERIES
PASS
ELEMENT

CURRENT
GENERATOR

STARTING
CIRCUIT

REFERENCE
VOLTAGE

OUTPUT
2

SOA
PROTECTION

ERROR
AMPLIFIER

THERRMAL
PROTECTION

GND
3

-6-

Chassis Block Diagram


IC 402 ( SRS TRUBASS )NJM2192 AM

-7-

Chassis Block Diagram


IC 401 (AV SWITCH W/IIC BUS CONTROL) M52797SP

-8-

IC Block Diagram
IC 101 ( SYSTEM TV SIGNAL PROCESSOR-TELETEXT) TDA93XXPS/N2/5I

-9-

IC Block Diagram
IC 103 ( DIGITAL TV SOUND DEMODULATOR/DECODER) TDA9874AH

-10-

IC Block Diagram
I C302( VERTICAL DEFLECTION BOOSTER) (TDA4863AJ)

IC404 (BTL AUDIO AMPLIFIER) (TDA8944J)

-11-

IC Block Diagram
Ic803( MULTISTANDARD COMB FILTE) (TDA9181T)

IC802(HEF4052)

-12-

IC Block Diagram
IC601<PHOTO TRANSISTOR> TLP621

TLP621
1

1:ANODE
2:CATHODE
3:EMITTER
4:COLLECTOT

IC604 < POWER SWITCH)> KA5Q12XXRF

-13-

Transistor Mark

-14-

Chassis wiring diagram


TO FRONT VIDEO IN
TO FRONT AUDIO IN

CN 203
TO H501

CN 202
TO KEYBOARD
CN 703
FROM CN801A

CN 805
TO CN 706

CN 806
TO CN 705

CN 701
FROM CN802A

CN401B
CN 803
TO CN 704
CN 802
CN 701

CN 706
FROM Cn805
+H403

FOCUS

CN 801A
TO CN 703

SCREEN
H502
FROM CN 302

CN401A

CN 301

H501
FROM CN 203

-15-

CN 602

CN 601

CAM350 PRO V 6.0 : Wed Jan 15 10:22:42 2003 - (Untitled)

CAM350 PRO V 6.0 : Wed Jan 15 10:17:54 2003 - (Untitled)

FRONT AV&RECEIVE PCB Top Layer


SIDE FRONT AV & AV PCB TOP LAYER

CONTROL PCB TOP LAYER

5800-D25TMY-01

-18-

Service Adjustments

-19-

Service Adjustments

-20-

Service Adjustments

-21-

Service Adjustments

-22-

Service Adjustments

-23-

Service Adjustments

-24-

Service Adjustments

-25-

Purity and Convergence Adjustment


COLOR PURITY ADJUSTMENT
(1) Before color purity adjustment,warm up the TV set over 15 minutes and fully degauss.
(2) Receive pure white signal in AV status and set the TV receiver dynamic.
(3) Go to factory mod MENU2. After write down the values of R-BIAS and B-BIAS, set the values of RBIAS and B-BIAS zero.
(4) Loosen the clamp screw of the deflection yoke and pull the deflection yoke towards color purity
Magnetic loop.
(5) Adjust color purity magnetic loop to make the green area at the center of CRT screen.
(6) Slowly push the deflection yoke toward the front of CRT and set it where a uniform green field is
Obtained. Tighten the clamp screw of the deflection yoke.
(7) Restore the values of R-BIAS,G-BIAS AND B-BIAS.

CONVERGENCE ADJUSTMENT
(1) Receive a dotted pattern. Set the TV receiver dynamic.
(2) Loose the convergence magnet clamperrrrr and align red with blu dots at the center of the screen by
rotating(R,B) static convergence magnets.
(3) Align Red/Blue with green dots at the center of the screen by rotating(RB-G) static convergence
magnet.
(4) Remove the DY wedges and slightly tilt the deflection yoke horizontally and vertically to obtain the
good

Purity Magnet
RB-G

RB

Magnet Clamper

Static Magnet

-26-

Control Location

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.

Main Switch
Power Indicator
Remote Sensor
Side AV In
Speakers
Program Down / Up Button
Volume Down / Up Button
Menu Button
Mute Button
AV/TV Button
YUV IN
Antenna Input Socket(75 Ohm)
S-Video In
AV IN 1
AV OUT
AC Power Cord

11 12 13 14 15

16

-27-

10

Input and Output Terminals

YUV IN

Cb

AV IN 1

Cr

AV OUT

VIDEO
AUDIO

LEFT

AUDIO

RIGHT
75 ANT
S-VIDEO

LEFT

LEFT

RIGHT

RIGHT

It can be connected to the following appliances: video-tape recorder, video camera, tape recorder and
audio amplifier, etc.....
*Please keep AC cord unplugged when connecting TV system.
*Do not connect S-Video In and AV IN 1 (VIDEO) together.

-28-

Operation Instructions

WARNING: The Main Power Switch ( No.1 of the Control Location page ) is the Manually Operated Mechanical
Switch . It is requested to Manually to turn On and Off the Main power. The Remote control can not cut off main
voltage at the TV set. For safety purpose, turn off the Main Switch manually when long time not use the TV or for
the long vacation. Press once will turn on the Main supply of the TV set. The Power indicator ( No.1 of the
Control Location page ) will light up. To make sure the power is turn off, please fully press the Main switch and
make sure the power indicator light off.

MENU BUTTON
1.Press this button to select PICTURESOUNDTIMETUNESETUPEXCHANGE menu cyclically.
PICTURE

SOUND

TIME

TUNE

SETUP

EXCHANGE

2.After entering an item, you can select the devised adjusting item by press the PROG.+/- Buttons or the
(GREEN) / BLUEbuttons,Then you can adjust it by press VOL.+/- Buttons or the +(RED) / - (YELLOW).

Picture Button
PICTURE
CONTRAST
BRIGHTNESS
COLOUR
SHARPNESS
HUE
BACK STRETCH
TILT
COMB FILTER

75
48
48
75
0
OFF
0
ON

1. You can select the CONTRAST.BRIGHTNESS.COLOUR.SHARPNESS.HUE.


BLACK.STRETECH.TILT.COMB FILER item by press the PROG+/- buttons
Or the (GREEN) / (BLUE) buttons.
2. You can adjust the CONTRAST.BRIGHTNESS.COLOUR.SHARPNESS.HUE.
TILT item by press VOL+/- buttons or +(RED) / -(YELLOW) buttons.
3. You can turn the BLACK STRETCH.COMB FILTER item ON or OFF you select
by press VOL+/- buttons or +(RED) / -(YELLOW) buttons.
*HUE is displayed only for NTSC system.
*TILT and COMB FILTER item is used by option.
*TILT is adjusted for GEOMAGNETISM ,You can change the TILT to shift
picture to a better position.
*When you set comb-filter ON ,the picture quality will have a greatly improvement.
*Comb-filter cannot be set ON when no colour or at S-VIDEO mode.

Sound Button

1. You can select the VOLUME.BASS.TREBLE.TRUBASS.SURROUND item by


Press the PROG+/- buttons or the (GREEN) / (BLUE) buttons.

SOUND
VOLUME
BASS
TREBLE
BALANCE
TRUBASS
SURROUND

6
50
50
0
ON
ON

2. You can adjust VOLUME.BASS.TREBLE item by press VOL+/- buttons or


+(RED) / -(YELLOW) buttons.
3. You can turn the TRUBASS.SURROUND item ON or OFF by press VOL+/buttons or +(RED) / -(YELLOW) buttons.
*TRUBASS item is used by option.
*TRUBASS technology is incorporated under license from SRS Labs ,Inc.

-29-

Operation Instructions

TIMERS
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG

--:---:-1
--:-20
--:-1

1.CLOCK
Press PROG+/- buttons or (GREEN) / (BLUE) buttons to select hour or
Minute.
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to adjust CLOCK
Time.
You can press CLOCK buttons to display current clock time.
2.ON TIME
Press PROG +/- buttons or (GREEN) / (BLUE) buttons to select hours
Or minute.
Press Vol+/- buttons +(RED) / -(YELLOW) buttons to adjust ON TIME.
3.ON PROG.
Press VOL+or +(RED) buttons to select ON PROGRAM.
4.OFF TIMER
Press PROG+/- buttons or (GREEN) / (BLUE) buttons to select hour or
Minute.
Press VOL+/- buttons or +(RED) /-(YELLOW) buttons to adjust REMIND
time.
5.SLEEP TIMER
Press VOL+/- buttons or +(RED)/-(YELLOW) buttons to set SLEEP TIME.
6.REMINDER TIMER
Press PROG+/- buttons or (GREEN)/ (BLUE) buttons to select hour or
minute.
Press VOL+/- buttons or +(RED)/-(YELLOW) buttons to adjust REMIND
TIME.
7.REMIND PROG
Press VOL+/- buttons or +(RED)/-(YELLOW) buttons to select REMIND
PROGRAM.
* Timer function will be reset when you switch off the TV set by the main
power switch or unpluged,And which will be working normally when you are
switch off the TV set by remote control.

-30-

Operation Instructions

SETUP Button

You can select the item by press PROG+/- buttons or (GREEN)/ (BLUE)
Buttons.
then you can adjust it press Vol+/- buttons or +(RED)/-(YELLOW) buttons.
1.LANGUAGE
You can select
ENGLISH
ARABIC
TURKIC
IRANIAN

SETUP
LANGUAGE
BACK GROUND
NOISE REDUCE
CHILD LOCK
CALENDAR

ENGLISH
ON
OFF
OFF

RUSSIAN

FRANCE

GERMAN

ITALIAN

2.BACK GROUND
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select it ON or
OFF ,For BACKGROUND when no signal is input at TV mode.
3.NOISE REDUCE
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select it ON or
OFF , for Noise REDUCE at TV mode.
4.CHILD LOCK
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select it ON or
OFF.
If you it set it ON,the key on the TV keyboard is disable and only the remote
control can be used.
5.CALENDAR
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to enter
CALENDAR menu.

CALENDAR

Y:2002

M:12

D:12

10

11

12

13

14

15

16

17

18

19

22

23

24

25

26

29

30

31

20
27

21
28

1.Press PROG+/- buttons or +(RED) / -(YELLOW) buttons to select


YEAR,MONTH or DATA.
2.Press VOL+/- buttons or +(GREEN) / -(BLUE) buttons to adjust
YEAR,MONTH or DATA.
3.Press MENU Button to return.
*Calendar setting will be reset when you are switch off the TV set by main
power switch or unpluged,And which will be working normally when you are
switch off the TV set by remote control.

-31-

Operation Instructions

TUNE MENU
TUNE
CONLOUR SYS
SOUND SYS
BAND
SKIP
PROGRAM
SEARCH
FINE TUNE
AUTO SEARCH

AUTO
M
VHF-L
OFF
2

You can select the item by press the PROG+/- buttons or the (GREEN) /
(BLUE) buttons.
1.COLOUR SYS
Press VOL+/- buttons or +(RED) / - (YELLOW) buttons to set the colour
system.
AUTO PAL NTSC NTSC443 SECAM
.2.SOUND SYS
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to set the sound
system.
I M DK BG
3.BAND
Press VOL+/- buttons or +(RED)/ -(YELLOW) buttons. You can select the
Band VHF-L.VHF-H or UHF.
VHF-L-----VHF-H-----UHF
4.SKIP
Press VOL+/- buttons or +(RED) / - (YELLOW) buttons to set skip on or
off,when you set skip on.this program will auto hided.
5.PROGRAM
Press VOL+/- buttons or+(RED)/-(YELLOW) buttons to set the PROGRAM
number.
6.FINE TUNE
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons can fine tune the
current program forward or backward for better quality.
7.SEARCH
Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to search for next
or previous available program,the set will auto stop white the signal is
received.
8.AUTO SEARCH
Press VOL+/- buttons or +(RED)/ -(YELLOW) buttons,the TV set will auto
Search in 3 bands and store every program.
*In AV mode,this item will display only COLOUR SYS.
*After fine tune. the program number colour will be change from GREEN
to YELLOW.

EXCHANGE MENU
EXCHANGE
PROGRAM
PROGRAM
EXCHANGE

1
1

In AV mode ,this item will not displayed.


1.Select the item by press the PROG+/- buttons or the (GREEN)/ (BLUE)
buttons.
2.Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select
PROGRAM 1.
3.Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select
PROGRAM 2.
4.Press VOL+/- buttons or +(RED) / -(YELLOW) buttons to select
EXCHANGE PROGRAM 1 and PROGRAM 2.

-32-

Operation Instructions

LOCATION OF CONTROL (REMOTE HANDSET UNIT)

- PRO

VOL

S.M.

--/---

P.M.

MENU

TV/AV

INDEX

LANG.
PIC.

SETUP

TUNE

REVEAL

SIZE

HOLD

SUB.PAGE

GAME

CLOCK.

TEXT

Q.VIEW

SUB.TIT

TYPE

MIX

CANCEL

SOUND

POWER (STAND BY) BUTTON (

Press this button to turn the TV on/off. Press any Number Button or Program Up/Down Button, picture and
sound will come on within a few seconds.

SLEEP BUTTON
Press it on display and set the sleep timer in 10 minutes step up to three hours. When the preset time runs
To 0, the TV set will go into stand by mode.
*If no program received,the TV set will switch to stand by auto after 5 minutes.

SOUND SYSTEM BUTTON (SYS.)


When the sound system is incorrect,Press this button to select the correct sound system.

STEREO/MONO DUAL I/II BUTTON(I/II)(OPTION)


The third line on the top right corner of the screen automatically changes to green when a NICAM broadcast is
received.
As stereo program is received.You can select STEREO.MONO.or FM by pressing the ST/MO/I/II button.
As bilingual program is received.You can select DUAL-1,DUAL-2 or FM by pressing the ST/MO/I/II button.
Remark:
FM:Standard mode
STEREO:Stereo mode
MONO:Mono mode
DUAL-1:multi sound channel for language 1 DUAL-2:multisound channel for language 2

PROGRAM UP/DOWN BUTTON (PROG +/-)


Press the Program Up Button to select the program forwards.
Press the Program Down Button to select the program backwards.
(Use this button for Page Up/Down to increase/decrease page number in TELETEXT mode.)

-33-

Operation Instructions

LOCATION OF CONTROL (REMOTE HANDSET UNIT)

VOLUME UP/DOWN BUTTONS (VOL+/-)


Press Volume Up/Down Buttons to adjust sound level.

PROGRAM SELECTION BUTTONS(0-9)


Push the number for your desired program and the program indicator will be displayed on the screen.
Press number key 0-199 for program selection.
Press the number keys to select teletext pages in teletext mode.

MUTE BUTTON(

Press once to mute the sound,press again to return to previously set sound level.MENU RECALL BUTTON.

MENU RECALL BUTTON(

Press this button sequential to recall for the program number,system, logo etc on the screen..

SOUND MODE BUTTON(S.M.)


Press this button to select the desired sound mode,USER.SPEECH.MUSIC and THEATER can be selected
cyclically.

PICTURE MODE BUTTON(P.M.)


Press this button to select the desired picture mode,RICH.USER.SOFT and STANDARD can be selected
cyclically.

DIGIT BUTTON(--/---)
Press this button to select program between 0-199 program.
For example,If you want to access program 8,press "8" key only,If you want to access program 88,you should
press this "--/---" button title the screen display "-",then press"8" "8"key,the TV set will switch to program 88;If
you want to access program 188,you should press this-/- button title the screen display"--",Then press"1"
"8" "8"key,the TV set will switch to program 188.

COLOUR BUTTONS(RED/YELLOW/GREEN/BLUE)
In TV mode, the (GREEN)/ (BLUE) buttons is used as PROG+/- buttons;the+(RED)/-(YELLOW) buttons is
usedas VOL+/- butotns.
In TELETEXT mode,press these colour buttons,the teletext will switch to the same colour page number which is
on button of the screen.

*All of the sound mode"SPEECH,MUSIC, THEATER" or picture mode "RICH,SOFT , STANDARD" are fix by
factory,all off the change of those setting will be save to the" USER"mode automatically.

-34-

Operation Instructions

LOCATION OF CONTROL (REMOTE HANDSET UNIT)(TELETEXT OPTION)


MENU BUTTON(MENU/INEDX)
In TV mode is used as a MENU command;in TELETEXT mode is used as a INDEX key.
MENU:To use MENU button for the turning procedure,please refer to page 7-10 for the details.
INDEX:Press INDEX button to obtain the index page.

AV MODE BUT TON (AV/LANG.)


In TV mode is used as a AV command;in TELETEXT mode is used as a LANG. key.
AV:Press this button to display external video signal such as VCR or CD video player.
LANG. :Press this button to switch the teletext LANGUAGE such as English or Russian.

SOUND MENU BUTTON(SOUND/ RECALL)


In TV mode used as a SOUND menu command;In TELETEXT mode is used as a REVEAL key.
SOUND:Press this button to enter into the SOUND menu directly.
RECALL :Sometimes the answers of quizes,jokes etc are hidden.Press REVEAL button to reveal the hidden
information.

PICTURE MENU BUTTON(PIC./SIZE)


In TV mode used as a PICTURE menu command;in TELETEXT mode is used as a SIZE key.
PIC.:Press this button to enter into the PICTURE menu directly.
SIZE:The top or botton half of any page can be enlarged by pressing this button.

SETUP MENU BUTTON(SETUP/HOLD)


In TV mode is used as a SETUP menu command;In TELETEXT mode is used as a HOLD key.
SETUP:Press SETUP button to enter into the setup menu directly.
HOLD:Sub-pages will scroll automatically.Press HOLD button a hold a sub-page. To release the page.press
HOLD again.

TUNE MENU BUTTON(TUNE/SUB.PAGE)


In TV mode used as a TUNE menu command;In TELETEXT mode is used as a SUB.PAGE key.
TUNE:Press this button to enter into the TUNE menu directly.
SUB.PAGE:Some pages attach sub-page,Page number may contain several subpages which are
automatically paged in a certain cycle by the TV station.Press this button once.0001 will be displayed on
screen,enter number key(0-9) to look for other sub-pages if available.If these is no sub-page,**** will be
displayed.To cancel this,press this button again.

GAME BUTTON(GAME/SUB.TITLE)
In TV mode used as a GAME command;In TELETEXT mode is used as a SUB.TITLE key.
GAME:You can play the game on TV. PROG- its used for speed up,PROG+ is used for transform.VOL- is
Used for shift left,VOL+ is used for shift right.
SUB.TITLE:Press SUB.TITLE button to view the sub-titles.

CLOCK BUTTON(CLOCK/TYPE)
In TV mode used as a CLOCK command;In TELETEXT mode is used as a TYPE key.
CLOCK:Display the time on the top right corner of the screen.
TYPE:Press this button to switch the teletext TYPE such as west/east type.

TEXT/BUTON(ON/MIX/OFF)
Press this button to display TELETEXT signal,mix TELETEXT page with TV signal and return to TV.
Note:To avoid mixing of External R.G.B while viewing Teletext.Disconnect scart plug or switch off external R.G.B
Source.

-35-

Operation Instructions

LOCATION OF CONTROL (REMOTE HANDSET UNIT)(TELETEXT OPTION)

Q.VIEW BUTTON(Q.VIEW/CANCEL)
In TV mode used as a Q.VIEW command;In TELETEXT mode is used as a CANCEL key.
Q.VIEW:Press this button to return to the previously viewed program.
CANCEL:If you want to watch TV but not cancel the TELETEXT mode completely.Press the CANCEL
button.When the last selected page is updated,the page number will be appeared at the top of the TV screen
Press the CANNEL button again to reveal the page.

-36-

Operation Instructions

BATTERY INSTALLATION (REMOTE CONTROL UNIT)

1. Remove the battery cover.


2. Insert the 2 UM3-AA 1.5V batteries making sure the polarity (+ or -) of the batteries matches the polarity
marks inside the unit.
3. Replace the battery cover.
Replace with new batteries when the TV set begins to show the following symptoms:
Operation is unsteady or erratic. Sometimes the TV set does not function with Remote Control Unit.

Remark:
1) Alkaline Batterie Recommended
2) Remove batteries when they are exhausted or if the remote control is not to be used for a long time.

THE CAUSES OF INTERFERENCE


Incorporated in your TV receiver are the most up-todate devices to eliminate interference. Local
radiation however, can create disturbances which
visibly affect your picture. Proper installation, a good
aerial are your best safe-guards against these
disturbances.

RF INTERFERENCE
Moving ripples across the screen are caused by
nearby transmitting or receiving-short-wave radio
equipment.

DIATHERMY
Herringbone pattern and partial picture loss can
result from the operation of diathermy equipment
from a nearby doctor's surgery or hospital.

SNOW
Weak TV signals from long distant stations result in
an instead picture and give the effect of falling snow.
An antenna adjustment or antenna amplifier may be
needed.

GHOST
Multiple image caused by TV signals reflected back
from surrounding buildings, hills, aircraft, etc. is
minimized by correct aerial positioning.

CAR IGNITION
Nearby cars and electrical motors can cause small
streaks across the picture or make the picture roll.

-37-

Mechanical Disassemblies
CABINET BACK REMOVAL

CHASSIS REMOVAL

1. Refer to Figure 1,remove 10 screws.


2. Pull off cabinet back and remove.

1. Remove cabinet back.


2. Discharge the picture tube anode(2nd anode lead) to the
dag coating (picture tube grounding lead).
3. Disconnect Degaussing coil socket(KE),Picture tube socket,
Deflection yoke connector (KDY), Speaker connectors(KL
and KR), and 2nd anode lead.
4. Remove chassis completely by sliding it straight back.

PICTURE TUBE REMOVAL


CAUTION: Do not disturb the deflection yoke
or magnet assembly on the picture tube
Neck. Care must be taken to keep these
assemblies intact, unless picture tube is
being replaced. Discharge the picture tube
to the coating before handing the Tube.
1. Remove chassis, referring to Chassis Removal instructions.
2. Place cabinet front face down on the soft surface.
3. Remove the screw on each corner of the picture tube and
GENTLY lift the picture tube out of the cabinet.
4. Install a replacement picture tube in reverse order.
Properly install the degaussing coil and picture tube
grounding lead on the picture tube. See Figure 2.

Note: If the Picture Tube is being replaced, mount the


Degaussing Coil on the picture tube. See following..

DEGAUSSING
COIL
DEGAUSSING
COIL HOLDER

PICTURE TUBE
GROUNDING LEAD

DEGAUSSING
COIL SOCKET

To CRT Unit
ground

-38-

Cabinet Parts List

10

9
6

Key No.
1
2
3
4
5
6
7
8
9
10

Part No.
SKCM 0025TM 0110
SK100729TM0001
SK100729TM0001
SK100925TM0001
SK100425TM0002
SK100829TM0001
SK060125TM00W6
SK100225TM0003
SK1016HS080006
SKHS08S0360600

Description
CABINET COLOUR MATCH-METAL SILVER GREY #MS G001
FRONT LENS (REMOTE CONTROL WINDOW)
FRONT LENS (LED WINDOW)
POWER KNOB-ELECTROPLATING SILVER(ABS)
SIDE AV JACK BRACKET-DARK GREY #DG001(ABS)
CONTROL KEY KNOB-ELECTROPLATING SILVER(ABS)
BACK LABEL FISHER TF25M2T W/PCB ENG
BACK CABINET-DARK GREY #DG001(HIPS)94V-0
BATTERY DOOR-METAL SILVER GREY #MSG001(ABS)
HANDSET-36 KEYS FOR OVERSEAS NORMAL GREY ENG (5N11)

-39-

21

19

17

15

13

11

CN601
H602

AC220V

2
1

CN601

SW601

D610
IN4148

DL601
JQX-14F

10

RT601

AV

CON4

CN705

20

18

16

14

12

10

V/AV3_R

A_ro
A_rin
A_lo
GND
B_G
A_lin
B
ID
G_G
NC
Green
NC
R_G
GND
R
BL
G
GND
Vo
Vin
G

10

CN702
CON4 Y U V /AV3

U/AV3_L

SCART1

P703

P702

P701

C104
4.7uF

Q613
C1815

4.7 NTC

R601

CN202
CON3

CN204
CON2

20

18

16

14

12

10

T601
15mH X 2

1
2

1
2
3
4
5
6
7
8

1
2
3
4
5
6

C625
2200pF/1KV

CN704
CON2

CN703
CON8

CN701
CON6

K0

K1

K2

K3

D0

D1

D2

D3

D4

D5

R612

10K
R611
47K

11

12

13

BRIDGE
KBJ6J

CN806
CON2

2
1

2
1

CN803
CON2

6
5
4
3
2
1

CN802
CON6

8
7
6
5
4
3
2
1

CN801
CON8

15 H

16 G

17 F

18 E

19 D

ZD601

JJ

C627
220u/16V

BAND

L: VL
M: VHF
H: UHF

20 C

14

R108
4.7K

Gnd

C101
100uF

Gnd

C628
47u/16V
+

R602
120K/2W

D600
BA158

IC601
KA5Q12XRF

C602
220nF/275VAC

T602
15mH X 2

5.0AL/AC250V

F601

2.2M/1W

R600

AGC

R166
680

C626
C604
2200pF/1KV
220nF/275VAC

1
2
3

1
2

A_ro
A_rin
A_lo
GND
B_G
A_lin
B
ID
G_G
NC
Green
NC
R_G
GND
R
BL
G
GND
Vo
Vin
G

SCART2

Gnd

21

19

17

15

13

11

IC801A
UPC6134

1
2
3
4
5
6

P707

P706

RESET

GND

X-INT

X-OUT

VDD

REM

S1

S2

D7

D6

CN706
Gnd CON6

R101
100K

C103 C105
10nF 10nF

R102
27K

REMOTE CONTROL

C132
100P

TUNING

Hi/n.c.

C102
100nF

R103 39K

8
CRYSTAL

R146
220

Z?

C804
0.1u

220P

C803

C100
100nF

39K

R149

Y/AV3

C801
47u

C802
220P

CN708
CON2

Q801
C2120

LED801

DEGAUSSING
H602

R802
1

C134
100nF

39K

R148

LED801

Q110
C2216

D104
1N4148

R149 10K

1
2

4
3
2
1

VT

AGC

1
2
3
4
5
6

Lo/BS2(SDA)

V+ 5.0V

i.c.(V+)

i.c.

+5V

Gnd

C607
1000pF

C610
47n

ZD601
4.7V

POWER

CN805
CON3

R819
1K
R812
1K

R828
1K
R821
1K

R831
1K

R603
C610
470
22n

C612
3.3n

R604
620

D603
BA158

10

L5MM
R605

L604

+ *C606
220uF/400V

D602 BA158

C613
100u/35V

D601
BA158

C628
2200pF/1KV

Gnd

10

S.M

-/--

P.M

VOL+ MUTE

Gnd

8.2M/1W

10

11

13
12

14

15

16

17

18

TLP621

2200pF/AC275V

C612

R617

IC601

BCK-50-0223

C604
0.01

T604

SYSTEM

IF

C815
0.01u

+8V

Gnd

R607

IN4 L

GND

NC

D607
EU201

Gnd

100

1N4148

Gnd
SW_C

R613

10K

R631

Gnd

Q607
Gnd C1815

R635
2K

Q602
A966

5.6K

R618

47K

R451

C620
100u/16V

R636 6.8/2W

C621
100u/16V

Gnd

Gnd

In Out

Gnd

Gnd

+ C630
100uF/16V

+5V

+ C633
100uF/16V

Gnd

Q608
C1815

+5V_A

C622
100uF/16V

+3.3V

OUT_R

OUT_L

10K

R235

Q215
3904

10K

>1V WORKING
<0.7V STANDBY

R452 47K

STANDBY

+5V

+8V

C630
Gnd 220u/16V

Gnd

+8V

2
1

2
1

C245
0.01u

R236

C214
47p

Q216
3904

TV_OUT

+3.3V

0.22u

C802

R618 47K

IC606
7805

IC605
7808

R622
1K
Q605
3
REF A
K
R623
1K
KA431

In Out

Q604
C1815

220/2W

R630

C635
22uF/100V

R627A
150/2W

R624
3.3K Q606
3
REF A
K
R625
10K KA431

Y_OUT

R832
1.8K

Y/CVBS

R842
10K

AUDIO_L
AUDIO_R

C801/C803
0.22u

Q803
S3904

C827
220u/16V

Gnd
Q801
J805
S3904 22

Q802
S3904

+8V

Gnd

R833
1.8K

Gnd

C823
1u
R823
R829
470
270

R830
47K

16
1.5V
15
5.0V
14
1.5V
13
0V
12
1.3V
11
0.4V
10
5.0V
9
0.6V

+ C824
100u

FSC

FSCSEL

R824
390

SYS2

SC

Gnd

+33V
+15V
R627
150/2W

SYS1

VCCA

+8V

AGND
Y/CVBS1

Y/CVBSout

OUTSEL

Cout

AM_audio

+12v

Mute

100

R111

Extin

Switch

+8V

+5V

+8V

Gnd

15

0V

14

0V

13

0V

12

0V

11

5.0V

10

1k

Gnd

+ C439
10uF

R424 8.2K

R422 8.2K

R420 36K

R423 3K

R421 22K

Gnd

TRUBASS

OPTION

Gnd

R256
2.2k

R258
1.8k

R272
75

Gnd

2.6V

+5V

GRAD

KEY

AV2

AV1

SDA

SCL

10uH

L112

R251
1.2k

R225

C3

C2

V+

VREFOUT

C1

C435
0.01

VERFIN

FIL9

GND

MODE2
GAINSW

FIL8

MODE1

PCOUT

BASSOUT

OUTL

FIL7
MOUT_R

OUTR

FIL6

INR

BASSINR

FIL5

NJM2192A

BASINL

FIL3

IC402

C4

INL

X205
XT-4.5

RD3
3.3K

SW2

R232
10

Gnd

3904
R231
1K

R263
1.2k

R226
470

R229
270

Gnd

+ C442
100u

+8V

+5v

R264
1.2k Gnd

R269
75

Cr_IN

R438
10K

Gnd
R440
47K

Q405
S3904

AUDIO_R

RD8
1K

RD9
47

0V
Vss
0V

SDA
3.2V

A2

n.c.
0V

WP
0V

Gnd

CR1
SW8 10u/16V

SCL
3.3V

PTC

Vdd
5.0V

SW7

24C08
IC102

TV_R

2.2
R131
10

10uH

Main_R

Gnd

C406

2.2K
Main_L

1
0V
2
4.0V
3
4.0V
4
4.0V
5
0.4V
6
0V
7
4.0V
8
2.8V
9
4.0V
10
7.8V
11
0V

C403
100u/16V

1u/N.P.

C405

1u/N.P.

C407
100u

R404
10K

R405
2.2K

MUTE

Gnd 0.01

C408

P2: MUTE
P1: BASS_CON
L: BASS IC On
H: BASS IC Off

L105

10uH

R130

Gnd

C179
100p

10K

R207

C230
0.47uF

R210
100K

+8V

R174
100

C213
0.1uF

gnd

Gnd

C237 10uF

Gnd

100

Gnd

Gnd
R211
27K

QSS

C211
22nF Gnd

FM

OUTM

P2

V_REF2

EXTIL

EXTIR

MONOIN

P1

Vssd3

NICAM

TDA9874

IC103

C117
0.47

n.c.

Csmo

MinL

P1

SCinL

n.c.

SCinR

P2

AinR

Cps1

n.c.

Gnd

C409
0.01

C116
0.01
Gnd Gnd Gnd

Gnd Gnd

Gnd

C411
68n

AUDIO CONTROL

IC401
TDA9859

5.1K

Gnd

C123
47p

L109
15uH

C176
0.1

680K

R330

Pclk

ADDR1

XTALO

XTALI

TP3

TEST2

I_ref

ADDR2

Vssa2

Vdec

test1

C412
0.15uF

Gnd

n.c.

n.c.

Ctr

LoutR

SCL

n.c.

SDA

LoutL

Ctl

n.c.

n.c.

+8V

C404
0.01

Gnd

Gnd

13k

R403
C402
68n

C401
0.15uF

+8V

FM_AUDIO
C_OUT
Y_OUT
CVBSINT

C122
20 0.47

Gnd

EW

R314
100
C314
100p

H_OUT

VDRB

VDRA

+8V

5
4
3
2
1

CN302

Gnd

R313
1K

Gnd

HEATER

GND

+200V

C313
2200pF/500V

Gnd
R402
100

C418
5.6n

SCL

C401 33nF
(NO TRUBASS)
(P20-21,P35-36)

4.0V
24
0V
23
0V

SDA

R401
100

1K

Gnd

1K

+8V

R448
10K +

R303

0.1

5.6
R321
270

Gnd

*C301
22n/630V

*C310
560n/400V
R305
10K/2W

V-DY

R326
5.6

C320
0.1

IC404

10

D301
RU4B

D302
BY228

TDA8944

6.0/2W

R315

S-Gnd

B+

+200V

+ C318
470u

Gnd

D312
BA158

KR

KG

KB

C531
2200p/500V

+200V

R529
1K

1K

R519

R509
1K

VERTICAL AMP

R318
2K

C325 R327

C532
10u/250V

C306
D303BA158
1.5K
1uF/250V
*C302A *C302B *C302C
T301
2.2n/2KV 7n2/2KV 8n2/2KV 1

H-DY
*L302
20uH

Gnd

BF421

Q523

D506
BA159

BF421

Q513

D509
BA159

J509
JT

BF421

Q533

D503
BA159

J502
JT

IC302
TDA4863

270

R525

BF420

Q522

R526
220

270

R515

BF420

Q512

R516
220

270

R535

BF420

2200p

C333

R536
220
Q532

R317
2K

C506
470PF

R524
22

R528
15K

C504
470PF

R514
22

R518
15K

C502
470PF

R534
22

R538
15K

R325
1/1W

R301
56

C311
680P

C446
1000u

1K

AUDIO_L

AUDIO_R

C445
100u

Gnd

R452
10K

C450
0.22

R451 10K

C316

GND

C455
0.22

Q409
C1815

IN4148

D410

R457
2.7K

R455
10K

10K

Gnd

R460
2.7K

R458
Gnd 13K

4.7K

R319

1
2

C460
CAP

2
1

+138V

+15V
-14V
V_PLUS

Q307
C1815

*R317
8.2K

8 12W

8 12W

SPEAKER

H401B

2
1

H401A

CN401B

1
2

CN401A

Gnd

SPEAKER

ABL

D308
1N4148

GND

V_PLUS

-14V

+15V

CON1

CN503

CON4

1
2
3
4

H502

CON1

CN504

R318
10K

+8V

R321 470

Gnd

120K

R316

G2

Focus

EHT

+ C459
100u

+3.3V

C457
0.1

R456
8.2

C458
+ 1000u

R459

Gnd

C456
10n

C309
100nF

R334
8 GND
2
ABL
1K/1W
7
HEATER

SCREEN

Gnd

IC301
STP5NK50ZFP

*R307 47K

EW J301

R491
100 1/6W

T490
2mH

2.2

R322

+ C317
470uF/25V

FOCUS1

11
EHT

C305
47u/50V(480mA)

L303 790uH

L501
100uH

S-Gnd

H-Gnd

H-Gnd

C534
4700pF/2KV

G3

EHT

G2

S-Gnd

G1

X705

CRT BOARD

Gnd

15.4V
R490 C490
3.3K 1/2W 220n/100V

R451
2K

22uF/50V

AUDIO AMP

R454 10K

C454
1.5n

C452
10u +

MODE:
0V: WORK
>6V:MUTE

Gnd

C451
1.5n C453
0.22

R453 10K
R450
2.7K

C449
0.22

Q410
C444 C1815
10n

Gnd

+15V

C448
Gnd 10n

ZD401
6.8V R449

C447
0.1

R447
8.2

R410
47K

6 GND
C321
Gnd
680P
D304 BA158
5 +15V
+
D309 BYW36
C317
C319
4 -14V
C307
Gnd 680P
Gnd
470uF/35V
D311
10uF/250V
+
3 AFC
BYW36
C318
470uF/35V
JF0501-21135
Gnd
R306
220K/0.5W

R302
2.7K +138V

*Q301
C5150

560p

C303

C324
2200p

D521
1N4148
S-Gnd

R523
270

S-Gnd

T302
H-DRIVER

S-Gnd

Q521
BF420

D501
1N4148

R522
2.2K

22

R521

Q511
BF420
R513
270

S-Gnd

R512
2.2K

22

R511

D501
1N4148
S-Gnd

R533
270

Q531
BF420

S-Gnd

R532
2.2K

22

R531

4700p

C304

4.7K

R331

C326
4.7u/250V
+

Gnd

ZD303
8V2

Gnd
C2482
Q304

R621
6.8K/3W

6.8K/3W

R620

R530
1K

+8V

S-Gnd

D530
1N4148

+8V

FBISO

1
2
3
4
5
6

CON6
H501

Gnd
33
R407 27K R406
C408
0V
+
32
100uF
2.2K
0V
C413 5.6n
31
Gnd
D403 IN4148
Gnd D404
4.0V
R439
30 C414
IN4148
Q403
4.0V 1u/50v
R409
1K
R443
S3904
29
1K
C415
3.2V
1K
100p
28
Gnd C416
0V
27
Gnd
100p
3.3V
R440
1K
26 C417
Q404
4.0V 1u/50v
S3904 R411
25
R442

R408
13k

19
Gnd
5.0V
18
2.0V
R134
17
8.2K
0V
16
0V
15
Gnd
1.6V
14
X101
1.6V
13 24.576MHz
5.0V
12
0.5V

0V

0V

21

22

OPTION

0V

U
Y
V
BLK
B

ABL

1
2
3
4
5
6

VIDEO_OUT

H_OUT

EHTO

FBISO

+8V

C226
100nF

C224
100nF

D201
IN4148

IRIN
OPT
+3.3V

R255 CN203
39K CON6

27K

C225
100nF

R215

ZD203
8V2

R228

Gnd

L203 10uH
+ C215
100uF/16V

L202 10uH

C218 L205 10uH


100uF/16V

Gnd
Gnd
C119
0.47
Gnd
C118
0.47
Gnd

10uH

C204
100nF

L201

ZD201 ZD202
Gnd 8V2 8V2

100

C219
3.3u

100

R206

R200

ZD205
5.1V

Gnd

C206
100nF

C205 Gnd
27pF

R205

C235
10nF
C236
220nF

C202
0.01u

C201
100uF/16V

C206
27pF

C212 100nF

R173
100

27K

R241

R212
1.8K

33

34

35

Gnd

R203 3.3k

R204 100

+ C216
100u

M001
(38K)

LED001

R201 10k

X101
12MHz

390
36 R209

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

CN003
CON5
RR1 100
RD11
1K

Vddd3

C115
0.01

34
0.1V
35
5.0V
36
0.2V
37
0V
38
N.C.
2.4V
39
N.C.
2.4V
40
N.C.
2.4V
C114 41
2.4V
47u
42
0V
C112 43
2.4V
0.01
44
0V

R127 100

L106

R435

+5V

+5V

10

R170

C180
C178 100p
0.47
Gnd

R128 100

Gnd
TV_L

3.3

R126

L110
10uH

Gnd

C113
0.47

10uH

L111

+5V

Standby
IRin
2.6V
4.9V
SCL
STAT
3.3V
0V
SDA
GRAD
3.2V
0V
Tuning
VddP
2.7V
3.3V
AV1
Reset
0V
0V
AV2
XTALout
5V
Key/Led
XTALin
3.3V
Status_AVGRAD
OscGnd
0V
0V
Vss C/P
VddC
0V
3.3V
Band1 0V
VpE
System
0V
M/L/L'
VddA
4.6V
3.3V
VssA
Bout
0V
3.1V
IC101
SECPLL
Gout
2.3V
TDA93XX/N2 3.1VRout
Vp2
7.9V
PHILIPS UOC 2.9V
DECDIG
Iblack
5.0V (TDA9363PS/N2
5.9V
TDA9365PS/N2
PH2LF
BCLin
TDA9384PS/N2 2.3V
3.5V
TDA9386PS/N2) B2/Uin
PH1LF
3.9V
2.5V
Gnd3
G2/Yin
0V
2.5V
DECBG
R2/Vin
4.0V
2.5V
AVL/EWD
Fblin
4.8V
4.0V
VDRB
AUDOUT/AMOUT
1.1V
3.3V
VDRA
CHROMA
1.1V
1.5V
IF1
CVBS/Y
1.9V
3.7V
IF2
Gnd1
1.9V
0V
IREF
CVBSINT
3.9V
3.9V
VSC
Vp1
3.8V
7.9V
Tuner AGC
IFVO/SVO
1.7V
3.3V
AUDEEM/SIF1
PLLIF
3.1V
2.4V
DECSDEM/SIF2
EHTO
2.3V
1.7V
Gnd2
AUDEXT/QSSO
0V
3.7V
SNDPLL/SIFAGC
FBISO
2.2V
0.5V
AVL/REFO 0V
0.6V H. out

+5V

CVBSINT
TO UOC P40

TV_IN

AUDIO_L

QSS ONLY

32

31

RD7
1.2K

SW6

C159
100pF

VIDEO_OUT
FROM UOC P38

Gnd

Q201
C1815

Q202
C1815

R262
4.7k

Gnd

R265
3.9k

+8v

28

27

26

25

24

23

22

21

20

19

18

17

29
+ C135
10uF 30

C166
100nF

C124
C234
Gnd 4.7uF
4.7uF

C173
330pF

R216
1K
R218
180

Q212

Gnd

Q212
3904

R217
10

+8V

C174
1.5nF

R271
75

Gnd

R252
1.8k

C138
2.2uF

C165
4700pF

16

C164
2200pF

14

13

12

11

10

15

220nF

C162

Gnd

10K

1
Gnd

R7
100

Gnd

C163
220nF

Gnd

ZD206
5.6V

R202

RD6
1.5K

SW5

C160
10nF
C161
100p
R213
2.7K
+3.3V R9
100

C168
C170 2200P
2200P
R222 3.3K

C231
0.1

Cb_IN

R145
15K
+ C130
1uF

RD5
2K

SW4

+5V

R161
10K

RD4
2.7K

SW3

30
C432
C433
4.0V
0.01
0.01
29
4.0V C414
Gnd
28
4.0V
27 10u
4.0V
26
4.0V
25 C417 10u
4.0V
24
4.0V
23
4.0V
22
4.0V
R436 10K
21
0V
R437 10K
20
0V
19
C437
10u
0V
18
C438
4.0V
10u
17
C440
4.0V
16
10u
7.9V
Gnd

180

R219

180

R221

180

FIL2

Gnd

L207 10uH

X205
XT-5.5

L207 10uH

X205
XT-6.0
R232 47

180
X205
XT-6.5
R224
L207 10uH

L207 10uH

Gnd

R253
3.9k

+8v

Q205
C1815

Q206
C1815

FSC

Gnd

C172
22nF R168 C171
100nF
39K

R164 100

R163 100

FIL1

FIL4

Gnd

C131
+ 100nF

R162 100

C129
100uF/16V

+8V

R250
4.7k

Gnd

C127
1000pF

VDRA

VDRB

EW

SYSTEM

FILOUT

2.6V

2.0V

2.6V

2.3V

0V

0V

0V

1
4.0V
2
C430 0.1 4.0V
3
4.0V
C429 4
0.1 4.0V
C421 R428 47K 5
0.1
4.0V
C422
6
0.1
4.0V
C423 R427 110K 7
0.1
4.0V
8
C425
0.1
R426 1.8K 4.0V
9
4.0V
10
C428 0.01 4.0V
11
4.0V
12
4.0V
C444 1u 13
0V
C443 10u 14
0V
15
0V

Vee

Vss

22k

R270

R259
47k

RD2
5.6K

SW1

R2 R4 R5 R6 R8 R10
4.7k 4.7k 4.7k 3.3K 3.3K
STANDBY4.7K

R1
4.7k

BAND

C221
0.1

SIF2

SIF1

AGC

IF2

IF1

C_out
Y_out

Y_IN

+8V

+5V

+3.3V

HEF4052

Gnd

Q203
C1815

Q204
A1015

R257

IC802

C222
0.1

+8v

TUNING

Gnd

0V
+8v Gnd
16
Vdd
+
7.7V

C233
100uF

+8V

10

11

FROM IC801
M52797
SYS:PAL/NTSC
L: PAL
H: NTSC

0.1V

FSC

+
C097
C107
12 0.01 4.7u

13

14

15

16

FSC_9Pin
R238 COMB:
10K 2.3V+FSC;
Y/C: +5V
BYPASS: 0V

R239 R237
47K 47k

AFout

AMin

Gnd

+8v

N.c.

IFin

OPTION

(SECAM L/L')

AMout

N.c.

Cref

Cagc

N.c.

IFin

R236
10K

47k

Gnd

R110

1k

10k

R117

3
4.7u
4

51

Q101
C1815

R115

VDDD

+8V

4.7u
Gnd
Q102
C1815

DGND

Y/CVBS2

INPSEL

Cin

IC803
TDA9181T

Gnd

R119
47K

R118Gnd
47K

Q103
A1015
R167
1K

SAW103
OFW_L9453

Q105
C1815 C140
C141

Gnd
+8v
R114 1.5K

R124
47K

1N4148

R161
4.7k

R820
10K

+5V

C805
1u
C804
10u
C806 Gnd
1u

C809
1u
C811
0.47u
C808
1u
C807
1u

R619 2.2/2W

Gnd

+12V
C624
+ 1000uF/25V

+15V

IC103
ZD33V

C631
100uF/200V
+33V

0.22
+ C626
1000uF/25V

220p/500V

D608 RU4B

C622

Gnd

FBISO

+140V

+138V

28
4.4V
27
4.2V
26
3.7V
25
4.2V
24
3.5V
23
3.0V
22
3.5V
21
3.7V
20
2.3V
19
4.4V
18
0.1V
17
0V
16
0V
15
0V

R639
0.47/3W

GND

SDA

C617
220p/2KV

CHIP SELECT

SCL

D5

IN3 R

IN4 R

BIAS

AV3 IN

D4

OUT R

V2 OUT

IN3 L

AV4 IN

OUT L

AV OUT

IN2 R

C623 220P/500V
*R609 8.2K
1
2
Q601
3
SE120
Gnd

C619
0.1

D604

Gnd

Gnd

Gnd

TV IN

IN2 L

TV_R IN

TV_L IN

VCC

AV2 IN

NC

VCC

IC801
M52797SP

C828 0.01u

Gnd

Q104
C1815

R112
47K

47K

R113

Gnd

1
1V
2
+5V
C234 0.01u 5.3V
3
Y/CVBS
1.7V
4
100u/16V
0V
L212 10uH
Gnd 5
C240
5.2V
6
5.2V
L211 10uH +
7
C239
0.5V
100u/16V
8
0V
R841
Gnd
47
ZD801
R242
5.1V
100

C_IN

Y/CVBS

D605 RU4A
+
C624
100uF/200V

+8V

D101

D102
R121 1N4148
4.7k

SYSTEM

1200p 47

R125
4.7k

L102
10u

C111 R122

COMB_FILTER

OPTION

SIF1
SIF2

(VIDEO/AUDIO SWITCHING)

+8V

1
C814 +
7.9V
2
100u
7.9V
IN2_L
Gnd C816 1u 3
R834
4.2V
AV2_IN
C817
47K
4
0.47u
R836
3.2V
C818 1u 5
IN2_R
75
R835
4.2V
C819 1u 6
47K
R822
4.2V
7
C821
47K
0.47u
R811
3.2V
C822 1u 8
75
R818
4.2V
47K
C803 1u 9
4.2V
10
C823
R810
0.47u
3.2V
75
C804 1u 11
4.2V
12
3.3V
R813 13
100
3.2V
14
R814
R826 R818 R813
100 0V
Gnd 4.7K 4.7K 4.7K
SCL
SDA

BLK:(RGB status)
Internal: 0.0...0.4 V
External: 1.0...3.0 V

OPT:(Video status)
Internal: 0.0...2.0 V
External (16:9): 4.5...7.0 V
External (4:3): 9.5...12.0 V

SW_C

R843
47K

Q804
S3904

Q.VIEW TEXT

PIC SOUND CLOCK GAME

MENU

VOL-

I/II PROG+ PROG-

S2

10K

Gnd
R143

SYS

S1

Gnd

SAW101
K6259K/K6263K
(K2962M/G3964M FOR CE)

C125
10nF

K9362M

ST

TUNE SETUP

1.8K

Gnd

Q112
C2717

R141
3.3K

BAT85

D103

PHILIPS CODE

R134
100

Q106
C2717

10nF

L104
0.82uH
C126

R144
10K

SAW102

R137
4.7K

K3

K1

R130
1.8K

C110
4700pF

R135
470

Gnd

+8V

K2

K0

C109
0.01u

R133
4.7K

AV/TV

R844

D7

D6

D5

D4

D3

D2

D1

D0

R840
75

R806
100K

VDD

R132
1K

R120
68

C108
10nF

IF

IN1_R R817
1K

AV1_IN

IN1_L

CVBS_R

CVBS_IN

CVBS_L

C627
2200pF/1KV

+5V

L101
10uH

C106
10nF

IFGND

10

i.c.(+33V)

TV_OUT
OUT-R
OUT-L

R136
10

R827
4.7K

IF1
IF2

C114
10nF

R821
4.7K

AM_AUDIO

TUNER
XG6VS96A

R816
4.7K

FM_AUDIO

11

R
G
B
BLK
OPT

3
2
1

TV_L
TV_IN
TV_R

+33V

NOTE: ACTIVE AREA , NO TOUCH WITH PERMITTION

AV1

TUNER

1
2

1
2

AV2

1
2
3
4
5
SCK

C619
1000p/2KV

SCL
SCL

+
SDD

SDA
SDA

vp4 -12.5v
4

IC103
TDA9830
SYS

R633

Vdda3

23

QSS
SIF1
TP2

SIF2
2.0V

vp1 +12.5v

Mi/BS1(SCL)

22K/1W

V_ref1
Nicam

-8.4V

+8v

Vssa3
Vssd2

WS
outR
AinL
MinR

G2

5P60 SCHEMATIC DIAGRAM

LinL

FOCUS

C601
220nuF/275VAC

KA5Q12XRF

Vdda1
Cps2
Vp

n.c.
n.c.

CRESET
n.c.
0V

Vssa1
SCoutL
SCoutR

0V
0V

V
OUT1-

Vssd1
MAD
Agnd

GND1

Vddd1
n.c.
Dgnd

Vcc1

EHT

3
3

OUT1+

out_L
1
2.4V
2
2.4V
3
4.8V
4
0V
5
0V
6
4.8V
7
0V
MoutL
MoutR

N.C.

33
0.7V
32
0V
31
0V
30
3.3V
29
3.5V
28
5.0V
27
0V
1uF
26
5.0V
25 C177
2.0V
24
LinR

IN1+

TP1
0V

INP
7
N.C.

10

1.0V
IN1-

11

INN
IN2-

0V

Vout
5
1

MODE

0V
Cbl1
Cbr1

-15.2V
IN2+

44
0V
43
4.0V
42
4.0V
41
4.0V
40
0V
39
0V
38
4.0V
37
4.0V
36
4.0V
35
4.0V
34
Cbl2
Cbr2

1.0V
+

Vp3 pump
3
N.C.

n.c.

n.c.

12
0V
13
3.9V
14
7.9V
15
4.0V
16
0V
17
0V
18
4.0V
19
4.0V
20
4.0V
21
4.0V
22
0V

OUT2-

GND2

0V
SVR

vp3 +16.4V
2
L490
141uH-284uH

1
Vcc2

OUT2+

0
1
2

+
3

1
7.8V
2
0V
3
15.8V
4
7.8V
5
0V
6
7.9V
7
0V
8
7.9V
9
7.9V
10
0.1V
11
7.9V
12
7.9V
13
0V
14
7.9V
15
0V
16
15.8V
17
7.8V

2
3

+
1

+
0

+
A0

+
A1

+
Vssa4

Sysclk

+
+

+3.3V

+
2 TO 4
Decoder
+

+15V

+
+

CRT

0.22n 630V

C301

JF0501-21119

15mH X 2

36uH

JF0501-2202

15mH X 2

36uH

C5148

220n 275V

7.6n 2KV

4.7n 2KV

2.2n 2KV

0.22n 630V

390n 400V

10 P.T.C.

5.6 2W

9.1K 1/4W

47K 1/4W

6.2K 1/4W

JF0501-2202

15mH X 2

40uH

C5148

220n 275V

8.2n 2KV

3.9n 2KV

2.2n 2KV

0.22n 630V

390n 400V

10 P.T.C.

5.6 2W

11K 1/4W

47K 1/4W

8.2K 1/4W

T5.0AL/250V T3.15AL/250V T3.15AL/250V T3.15AL/250V

JF0501-21135

15mH X 2

C5148

220n 275V

8.2n 2KV

5.6n 2KV

2.2n 2KV

0.22n 630V

470n 400V

10 P.T.C.

2.2 2W

11K 1/4W

47K 1/4W

BY :

REV DATE :

APPROVED BY:

CHECKED BY:

ISSUED

SYSTEM

P/N

TITLE

2003-12-1

PAL/SECAM/NTSC BG/DK/I/M
NICAM/TELETEXT/TRUBASS/COMB
2 SCART/YUV/S_VIDEO/AV_IN/OUT

0502-D29001-04

5P60 SCHEMATIC DIAGRAM

NOTE:
(1) All resistors are in OHM, all coils are in H ang
all crystals are in HZ.
(2) The area enclosed by ----is LIVE ares and is
directly cnnected to main voltage .
(3) The device indicated with
are safety critical devices.
(4) The device indicated with *are subject to change or
omit according to TV designs.
(5) The area enclosed by----is optional .
(6) The circuit is subject to change without notice

F601

T301

T602

20uH

C5150
Q301
L302

220n 275V

8.2n 2KV

7.2n 2KV

C601

C302C

C302B

2.2n 2KV

560n 400V

C310

C302A

10 P.T.C.

RT601

6.0 2W

8.2K 1/4W
R315

75K 1/4W
R317

6.2K 1/4W

34" NOVEL 29" LG PHILIPS 29" ORION 29"LG.PHILIPS


M78KXC110 A68KYN690
A68QDL080 A68QCU259
X 01
X 520MGF
X013(B)
X56S
8.2K 1/4W
R307

R609

ITEM

You might also like