Professional Documents
Culture Documents
MALAYSIAN
STANDARD
12S005R0
Fo
r
Pu
b
lic
om
en
ICS: 29.140.99
Descriptors: minimum, energy, performance, MEPS, lamps
Copyright 2014
DEPARTMENT OF STANDARDS MALAYSIA
Fo
r
Pu
b
lic
m
om
C
t
en
12S005R0
Contents
Page
Scope ............................................................................................................................ 1
Fo
r
Pu
b
lic
om
en
12S005R0
Committee representation
The Industry Standards Committee on Electrical and Electronics Equipments and Accessories (ISC S) under whose
authority this Malaysian Standard was developed, comprises representatives from the following organisations:
om
en
The Technical Committee on Lighting, Lamps and Accessories which supervised the development of this Malaysian
Standard consists of representatives from the following organisations:
Pu
b
lic
Fo
r
The Working Group on Minimum Energy Performance Standards (MEPS) for Lighting which developed this
Malaysian Standard consists of representatives from the following organisations:
ii
12S005R0
Foreword
This Malaysian Standard was developed by the Working Group on Minimum Energy
Performance Standards (MEPS) For Lighting under the authority of the Industry Standards
Committee on Electrical and Electronics Equipments and Accessories.
MEPS for electrical appliances have been introduced to the Malaysian market since 2009.
Since then, development has been carried out by Suruhanjaya Tenaga to put MEPS
requirement in the Electricity Regulation 1994.
The amendment of Electricity Regulation 1994 enables the enforcement of MEPS and
labelling of specified electrical appliances (equipment).
Fo
r
Pu
b
lic
om
en
Compliance with a Malaysian Standard does not of itself confer immunity from legal
obligations.
iii
Fo
r
Pu
b
lic
m
om
C
t
en
12S005R0
en
b) self ballasted single capped lamps (compact fluorescent lamps - CFL) for general lighting
services;
c) single capped fluorescent lamps (non-integrated compact fluorescent lamps) and circular
fluorescent lamps for general lighting services;
om
d) self ballasted Light Emitting Diode (LED) lamps for general lighting services; and
lic
2 Normative references
Pu
b
The following normative references are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the normative reference (including any amendments) applies.
MS IEC 60061-1, Lamp Caps amd Holders together with gauges for the control of
interchangeability and safety - Part 1
Fo
r
MS IEC 60064, Tungsten filament lamps for domestic and similar general lighting purposes
Performance requirements
MS IEC 60081, Double-capped fluorescent lamps - Performance specifications
MS IEC 60901, Single-capped fluorescent lamps - Performance specifications
MS IEC 60969, Self-ballasted lamps for general lighting services - performance requirements,
MS IEC 62612, Self-ballasted LED lamps for general lighting services with supply voltages >
50 V - Performance requirements
MS IEC 62717, LED modules for general lighting - Performance requirements
IES LM-80-08, Approved Method: Measuring Lumen Maintenance of LED Light Sources
12S005R0
efficacy
Efficacy (lm/W) is the amount of light emitted measured in lumen (lm) by a lamp for each
watt (W) of power consumed.
3.2
The minimum level of energy efficiency which shall be met by each individual unit of the
lamps.
en
om
The energy efficiency performance criteria will be the measured efficacy of the lamp in
lumen/watt which shall be determined in accordance with the relevant standards.
5 MEPS requirements
lic
ii)
the endurance parameters tested shall not be less than 80 % of the initial lumen
output value after 2 000 h operation; and
Pu
b
i)
Fo
r
T8
T5
MEPS (lm/W)
18 to 30
70
> 31
80
14
75
> 15
80
12S005R0
b) self ballasted single capped lamps (compact fluorescent lamps - CFL) for general lighting
services;
i)
ii)
the endurance parameters tested shall be not less than 80 % of the initial lumen
output value after 2 000 h operation; and
5 to < 9
46
9 to < 15
52
16 to 24
55
en
62
om
> 25
c) single capped fluorescent lamps (non-integrated compact fluorescent lamps) and circular
fluorescent lamps for general lighting services;
the performance testing standards shall be in accordance with MS IEC 60901;
ii)
the endurance parameters tested shall be not less than 80 % of the initial lumen
output value after 2 000 h operation; and
Pu
b
lic
i)
Fo
r
< 10
46
10 to 18
55
19 to 26
59
> 27
70
d) self ballasted Light Emitting Diode (LED) lamps for general lighting services; and
i)
ii)
the LED chips / module shall comply with MS IEC 62717 or IES LM-80-08;
12S005R0
iii) the endurance parameters for the MS IEC 62612 test in i) shall be not less than 80 %
of the initial lumen output value and not more than 10 % of failures after minimum
1 000 h operation;
iv) for LED lamps with chips not in compliance with ii), shall be tested in for 6 000 h in full
compliance to MS 62612 with minimum 70 % of the initial lumen output value and not
more than 50 % of failures; and
v) the MEPs value for lamps of different terminals as shown in Table 4.
Table 4. Self ballasted Light Emitting Diode (LED) lamps for general lighting services
Minimum Efficacy (lm/W)
G13
75
GU10
50
en
60
E27 or B22d
60
om
E14
ii)
Fo
r
Pu
b
lic
i)
Acknowledgements
en
Fo
r
Pu
b
lic
om