Professional Documents
Culture Documents
La perforacin consiste en mudar un taladro, vestir el equipo y conectar una mecha o una
sarta de tubera de acero para penetrar las formaciones suficientes hasta construir un hoyo til
que comunique los fluidos del yacimiento con la superficie. Esto ocurre con la ayuda de torres de
perforacin .
Las cuales son estructuras de acero montadas sobre la boca del pozo para soportar la tubera de
perforacin y otros equipos que son descendidos y elevados durante las operaciones de
perforacin.
Las torres de perforacin son utilizadas para realizar perforaciones de entre 800 y
6000 metros de profundidad en el subsuelo, tanto de pozos de gas, agua o petrleo,
as como sondeos de exploracin para analizar la geologa y buscar nuevos
yacimientos.
Cuando las perforaciones se realizan en el mar estas torres estn montadas sobre
barcazas con patas o buques con control activo de su posicin respecto del fondo
del mar y se denominan plataformas petrolferas.
2) Proceso de perforacin de pozos mediante la torre de
perforacin:
La broca de perforacin o trpano, empujada por el peso de la sarta y las bridas
sobre ella, presiona contra el suelo.
Se bombea lodo de perforacin (mud) dentro del cao de perforacin, que
retorna por el exterior del mismo, permitiendo la refrigeracin y lubricacin de la
broca al mismo tiempo que ayuda a elevar la roca molida.
El material que resulta de la perforacin es empujado a la superficie por el lodo de
perforacin, que luego de ser filtrado de impurezas y escombros es rebombeado al
pozo. Resulta muy importante vigilar posibles anormalidades en el fluido de retorno,
para evitar golpes de ariete, producidos cuando la presin sobre la broca aumenta o
disminuye bruscamente.
La lnea o sarta de perforacin se alarga gradualmente incorporando
aproximadamente cada 10 metros un nuevo tramo de cao en la superficie.
Todo el proceso se basa en una torre de perforacin que contiene todo el
equipamiento necesario para bombear el fluido de perforacin, bajar y elevar la
lnea, controlar las presiones bajo tierra, separar las rocas del fluido que retorna, y
generar in situ la energa necesaria elctrica y mecnica para la operacin,
generalmente mediante grandes motores disel.
Jack Up, Tritn o Autoelevadisas: Perfora pozos en costa afuera, ste posee pilares
que soportan la cubierta del equipo. Dichos pilares se apoyan en el fondo del mar o
lago, y posterior mente se eleva la plataforma del nivel del agua.
Sumergibles: Son equipos que permanecen en el fondo del mar o lago mientras
perforan, son utilizados en aguas poco profundas. Tienen unos compartimientos que
se inundan para que se pueda sumergir. Los hay de Barcazas de pilares, Sumergible
rtico, entre otros.
11. Aparejo
12. Cable del aparejo
13. Bloque corona
14. Estructura
15. Piso del enganchador
16. Tiros (3 barras de 9 metros por cada tiro es lo usual)
17. Rack
18. Conexin de lodo giratoria (en equipos modernos se reemplaza por el top drive)
19. Barra de perforacin (rota junto con la mesa, aunque puede moverse hacia
arriba y abajo libremente)
20. Mesa rotativa (acciona la barra de perforacin)
21. Piso de perforacin
22. Bell nipple
23. Vlvula (BOP) anular
24. Vlvula (BOPs) ciega y de caera
25. Sarta de perforacin
26. Trpano
27. Cabeza del casing
28. Lnea de retorno de lodo.
Rig equipment
The equipment associated with a rig is to some extent dependent on the type of rig but (#23 &
#24) are devices installed at the wellhead to prevent fluids and gases from unintentionally
escaping from the borehole. #23 is the annular (often referred to as the "Hydril", which is one
manufacturer) and #24 is the pipe rams and blind rams. In the place of #24 Variable bore rams or
VBR's can be used, they offer the same pressure and sealing capacity found in standard pipe
rams, while offering the versatility of sealing on various sizes of drill pipe, production tubing and
casing without changing standard pipe rams. Normally VBR's are used when utilizing a tapered
drill string (when different size drill pipe is used in the complete drill string).
Centrifuge: an industrial version of the device that separates fine silt and sand from the
drilling fluid.
Solids control: solids control equipments for preparing drilling mud for the drilling rig.
Chain tongs: wrench with a section of chain, that wraps around whatever is being
tightened or loosened. Similar to a pipe wrench.
Degasser: a device that separates air and/or gas from the drilling fluid.
Desander / desilter: contains a set of hydrocyclones that separate sand and silt from the
drilling fluid.
Drawworks: (#7) is the mechanical section that contains the spool, whose main function
is to reel in/out the drill line to raise/lower the traveling block (#11).
Drill Bit: (#26) is a device attached to the end of the drill string that breaks apart the rock
being drilled. It contains jets through which the drilling fluid exits.
Drill pipe: (#16) joints of hollow tubing used to connect the surface equipment to the
bottom hole assembly (BHA) and acts as a conduit for the drilling fluid. In the diagram,
these are "stands" of drill pipe which are 2 or 3 joints of drill pipe connected together and
"stood" in the derrick vertically, usually to save time while tripping pipe.
Elevators: a gripping device that is used to latch to the drill pipe or casing to facilitate the
lowering or lifting (of pipe or casing) into or out of the borehole.
Mud motor: a hydraulically powered device positioned just above the drill bit used to
spin the bit independently from the rest of the drill string.
Mud pump: (#4) reciprocal type of pump used to circulate drilling fluid through the
system.
Mud tanks: (#1) often called mud pits, provides a reserve store of drilling fluid until it is
required down the wellbore.
Rotary table: (#20) rotates the drill string along with the attached tools and bit.
Shale shaker: (#2) separates drill cuttings from the drilling fluid before it is pumped back
down the borehole.