You are on page 1of 520

USER DESCRIPTION_x000D_Transport

Network Parameters

1 (520)

Transport Network Parameters


WCDMA RAN W14
Copyright

Doc Number:

87/1553-HSD 101 02 Uen

Ericsson AB 2011-2014. All rights reserved. No part of this document


may be reproduced in any form without the written permission of the
copyright owner.

Revision:

M3

Disclaimer
The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson
shall have no liability for any error or damage of any kind resulting from the
use of this document.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: Heading

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

2 (520)

Transport Network Parameters


87/1553-HSD 101 02 Uen

1. Introduction
1.1 Purpose
This document describes the WCDMA RAN Transport Network parameters as seen by the operator.
The User Description is mainly written for operators. Its intended use is as a dictionary for more in depth descriptions of the
WCDMA Transport Network parameters.
1.2 Scope
This document lists and gives information about the WCDMA RAN Transport Network Parameters. It contains a general description
of the parameter, unit, value, range, syntax description and reference to GUI.
1.3 Structure
The following information is presented for each parameter:

MO Class Name
Parameter Name
Node
Parameter Description
Data Type
MOM Range
Valid Values
Default value
Recommended Value

Prepared: EZIEAGA

Managed object class the attribute belongs to.


Attribute name as defined in the MOM.
Indicates the node to which the parameter belongs (where it is created and configured).
A brief description of the parameter. Unit and resolution of the default and recommended value is also
included together with syntax if applicable.
The data type for the parameter. E.g. Long, string.
The range of values for the parameter.
Valid values for enumerated data types.
The default value, as initially set by the system, if not explicitly set at MO creation.
The value recommended at initial system launch in case one single value is recommended. The value may
be the same as the Default value or different.
The field is blank if there is no recommended value or if the recommended value depends of usage.

Date: 2014-05-27
Sheet: Introduction

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Initial Parameter Value Source

Network Parameters

3 (520)

Source for initial configuration of parameters of access type Read & Write and Restricted. The source can
be:
- TND: The parameter shall be configured according to Transport Network Design. Typically the parameter
is a network address or reference e.g. to connect a certain ATM port to a certain physical port.
- CPI: There are recommendations in another CPI for how to configure the parameter, see CPI reference.
The recommendation depends on usage of function, therefore no generic recommendation can be given.
- Default: The parameter is recommended to be configured according to it's Default value, see Default
value.
- Recommended: The parameter is recommended to be configured to a different value than the Default
Value, see Recommended value.
- TND O&M: The parameter shall be configured according to O&M preferences for the Transport Network
This could be parameters controlling RDI reporting, degradation thresholds etc. The supplied default
values may be used without change or can be changed according to operator preferences.
Parameters userLabel and administrativeState have no classification.

CPI reference
Access

Reference to the RAN functional CPI covering this parameter.


Indicates if the parameter is Read only, Read & write or Restricted. If restricted, once the corresponding
MO has been created, the parameter value can only be retrieved (not set) . It could only be modified by
recreating the MO.

Mandatory

Indicates whether or not this parameter is mandatory to configure at creation of the corresponding
managed object. For mandatory parameters no default value is defined.
Indicates whether or not the parameter is stored persistently in the database of a node. Persistent data will
survive a node restart.

Persistent

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: Introduction

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Notification

Indicates whether or not the Management system will be informed when the parameter value is changed
by the system or by a Management set operation.
The OSS-RC network manager automatically receives every notification but the RNC and RBS element
managers first have to subscribe to a notification.

Sequence
BulkCM MO Class name
BulkCM Parameter Name
Functional Area

Indicates whether or not the parameter represents a sequence of values.


The name of the BulkCM managed object class this parameter belongs to.
The name of the parameter in the BulkCM interface.
A classification of parameters in functional areas. The areas are:
- ATM Connection
- Connection Control
- IP O&M
- IP Transport
- Network Sync
- O&M PM Statistics
- Physical Interface
- Radio Protocols
- Signalling Bearer
- TN Administration
- TN PM Counters

Parameter Group

A classification of parameters in parameter type groups. The groups are:


- EnumRef
- Id
- Label
- MORef
- Real
- Status
- StructRef
- Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: Introduction

4 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

5 (520)

Transport Network Parameters


87/1553-HSD 101 02 Uen
MO Class Name
Aal1TpVccTp
Aal1TpVccTp

Parameter Name
Aal1TpVccTpId
Aal1TpVccTpId

Node
RBS DUW
RNC

Parameter Description
The value component of the RDN.
The value component of the RDN.

Data Type
string
string

Aal1TpVccTp

alarmReport

RBS DUW

Specifies which type of alarms are reported.

Aal1TpVccTp

alarmReport

RNC

Aal1TpVccTp

availabilityStatus

RBS DUW

MOM Range

Valid Values

Default Value

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

Specifies which type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Aal1TpVccTp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Aal1TpVccTp

cdvt

RBS DUW

Aal1TpVccTp

cdvt

RNC

Specifies the Cell Delay Variation Tolerance (CVDT). Refer to ATM Forum
for more details.

Recommended Value

long

100..4000

1000 See CPI

long

100..4000

1000 See CPI

Unit: 1 microsecond
Specifies the Cell Delay Variation Tolerance (CVDT). Refer to ATM Forum
for more details.
Unit: 1 microsecond

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal1TpVccTp

continuityCheck

RBS DUW

Network Parameters

Specifies whether VC end-to-end continuity check is active.

6 (520)

boolean

Continuity checking means that a cell is sent downstream when no user


cell has been sent for a period of nominally 1 second. Continuity check
both enables generation of continuity check cells as well as detection of
LOC.
Activation/Deactivation should be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Aal1TpVccTp

continuityCheck

RNC

Specifies whether VC end-to-end continuity check is active.

boolean

Continuity checking means that a cell is sent downstream when no


user cell has been sent for a period of nominally 1 second. Continuity
check both enables generation of continuity check cells as well as
detection of LOC.
Activation/Deactivation should be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Aal1TpVccTp

counterActivation

RBS DUW

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has been
used in the PMS interface.
Aal1TpVccTp

counterActivation

RNC

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has
been used in the PMS interface.

Aal1TpVccTp

counterMode

RBS DUW

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Aal1TpVccTp

counterMode

RNC

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Aal1TpVccTp
Aal1TpVccTp

ds0BundleId
ds0BundleId

RBS DUW
RNC

Reference to an instance of Ds0Bundle MO.


Reference to an instance of Ds0Bundle MO.

Ds0Bundle
Ds0Bundle

Aal1TpVccTp

nomPmBlockSize

RBS DUW

Nominal block size for PM. The minimum number of ATM cells that is sent
before sending a Forward Performance Monitoring (FPM) cell.

AtmNomPmBlkSize

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

7 (520)

Aal1TpVccTp

nomPmBlockSize

RNC

Nominal block size for PM. The minimum number of ATM cells that is sent
before sending a Forward Performance Monitoring (FPM) cell.
Unit: 1 cells

AtmNomPmBlkSize

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

Aal1TpVccTp

operationalState

RBS DUW

The operational state.

OperState

Aal1TpVccTp

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Aal1TpVccTp

partialFill

RBS DUW

Indicates how many bytes are filled in each ATM cell. The value 47
indicates that cells are not partially filled, that is, all cells are filled
completely.

long

23..47

47

47

long

23..47

47

47

Partial filling of cells is used in circuit emulation, to reduce packetization


delay. Refer to the ATM Forum specifications for more details.
If partial filling is used, a maximum of 10 time slots can be configured on
the MO Ds0Bundle that is used by the MO Aal1TpVccTp.

Aal1TpVccTp

partialFill

RNC

Indicates how many bytes are filled in each ATM cell. The value 47
indicates that cells are not partially filled, that is, all cells are filled
completely.
Partial filling of cells is used in circuit emulation, to reduce
packetization delay. Refer to the ATM Forum specifications for more details.
If partial filling is used, a maximum of 10 time slots can be
configured on the MO Ds0Bundle that is used by the MO Aal1TpVccTp.

Aal1TpVccTp
Aal1TpVccTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal1TpVccTp
Aal1TpVccTp

vclTpId
vclTpId

RBS DUW
RNC

Reference to an instance of VclTp MO.


Reference to an instance of VclTp MO.

VclTp
VclTp

Aal2Ap
Aal2Ap

Aal2ApId
Aal2ApId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal2Ap

aal2QoSCodePointProfileId

RBS DUW

The identity of the QoSCodePointProfile used by this MO.

Aal2QosCodePointProfile

If this attribute is not specified, no QoS information is sent in outgoing


signalling messages from this AAL2 AP.
If this attribute is not specified, QoS Class A is assumed for incoming
signalling messages to this AAL2 AP.
When this attribute has been set, it cannot later be reset it to NULL, that is,
not referencing any Aal2QosCodePointProfile MO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2Ap

aal2QoSCodePointProfileId

RNC

Network Parameters

The identity of the QoSCodePointProfile used by this MO.

8 (520)

Aal2QosCodePointProfile

If this attribute is not specified, no QoS information is sent in


outgoing signalling messages from this AAL2 AP.
If this attribute is not specified, QoS Class A is assumed for
incoming signalling messages to this AAL2 AP.
When this attribute has been set, it cannot later be reset it to NULL,
that is, not referencing any Aal2QosCodePointProfile MO.

Aal2Ap

allocationMode

RBS DUW

This attribute indicates if the RPU allocation for the AAL2 AP and its Path
Distribution Units is manual or automatic.

Aal2AllocationMode

MANUAL = 0
AUTOMATIC = 1

MANUAL(0)

MANUAL(0)

Aal2AllocationMode

MANUAL = 0
AUTOMATIC = 1

MANUAL(0)

Iu, Iur: MANUAL(0)


Iub: AUTOMATIC(1)

The manual allocation mode is supported for all types of AAL2 APs, but the
automatic allocation mode is only supported for AAL2 APs using UNI-SAAL
as signalling bearer. If an AAL2 AP is created with the attribute sigLinkId of
type Mtp3bAp, the attribute allocationMode should either not be set at all or
it should be set to MANUAL.
If the MO is created with allocationMode = MANUAL, the attribute rpuId
must be set. If the MO is created with allocationMode = AUTOMATIC, rpuId
must not be set.
If the allocationMode is changed from AUTOMATIC to MANUAL, the
existing RPU allocation will be kept until the rpuId is set again.
If the allocationMode is changed to AUTOMATIC, the existing RPU
allocation will be kept until a reallocation is initiated by the reallocate action
or if the RPU becomes faulty.

Aal2Ap

allocationMode

RNC

This attribute indicates if the RPU allocation for the AAL2 AP and its Path
Distribution Units is manual or automatic.
The manual allocation mode is supported for all types of AAL2 APs,
but the automatic allocation mode is only supported for AAL2 APs using
UNI-SAAL as signalling bearer. If an AAL2 AP is created with the attribute
sigLinkId of type Mtp3bAp, the attribute allocationMode should either not
be set at all or it should be set to MANUAL.
If the MO is created with allocationMode = MANUAL, the attribute
rpuId must be set. If the MO is created with allocationMode = AUTOMATIC,
rpuId must not be set.
If the allocationMode is changed from AUTOMATIC to MANUAL,
the existing RPU allocation will be kept until the rpuId is set again.
If the allocationMode is changed to AUTOMATIC, the existing RPU
allocation will be kept until a reallocation is initiated by the reallocate action
or if the RPU becomes faulty.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2Ap

availabilityStatus

RBS DUW

The availability status.

Network Parameters
AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Aal2Ap

availabilityStatus

RNC

The availability status.

9 (520)

It contains details about operationalState.

Aal2Ap
Aal2Ap

nrOfConfiguredAal2Paths
nrOfConfiguredAal2Paths

RBS DUW
RNC

The total number of Aal2PathVccTp MOs configured on this Aal2 Ap.


The total number of Aal2PathVccTp MOs configured on this Aal2 Ap.

Aal2Ap

nrOfRemotelyBlockedAal2Paths

RBS DUW

Number of Aal2PathVccTp instances that are connected to this Aal2Ap MO long


and where remoteBlockingState is REMOTELY_BLOCKED.

Aal2Ap

nrOfRemotelyBlockedAal2Paths

RNC

Number of Aal2PathVccTp instances that are connected to this Aal2Ap MO long


and where remoteBlockingState is REMOTELY_BLOCKED.

Aal2Ap

nrOfUnavailableAal2Paths

RBS DUW

The total number of unavailable Aal2PathVccTp instances on this Aal2Ap long


MO, that is the number of Aal2PathVccTp MOs connectected to this
Aal2Ap MO, where administrativeState is LOCKED and operatonalState is
DISABLED.

Aal2Ap

nrOfUnavailableAal2Paths

RNC

The total number of unavailable Aal2PathVccTp instances on this Aal2Ap long


MO, that is the number of Aal2PathVccTp MOs connectected to this
Aal2Ap MO, where administrativeState is LOCKED and operatonalState is
DISABLED.

Aal2Ap

operationalState

RBS DUW

The operational state.

OperState

Aal2Ap

operationalState

RNC

The operational state.

OperState

Aal2Ap
Aal2Ap

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

long
long

0
0

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2Ap

rpuId

RBS DUW

Network Parameters

The location of an AAL2 AP program represented by a reference to a


ReliableProgramUniter MO.

10 (520)

ReliableProgramUniter

When setting the rpuId, the attribute reliableProgramLabel for the new
rpuId must be the same as for the previous rpuId.
The rpuId must be specified when the MO is created with allocationMode
set to MANUAL. The rpuId must not be set if the MO is created with
allocationMode set to AUTOMATIC, but the value of rpuId can still be read.

Aal2Ap

rpuId

RNC

The location of an AAL2 AP program represented by a reference to a


ReliableProgramUniter MO.

ReliableProgramUniter

When setting the rpuId, the attribute reliableProgramLabel for the


new rpuId must be the same as for the previous rpuId.
The rpuId must be specified when the MO is created with
allocationMode set to MANUAL. The rpuId must not be set if the MO is
created with allocationMode set to AUTOMATIC, but the value of rpuId can
still be read.

Aal2Ap

secondarySigLinkId

RBS DUW

Reference to a UniSaalTp MO that is used as a secondary signalling link.


This attribute can be set only when sigLinkId is of type UniSaalTp.

ManagedObject

The reference to the secondary signalling link can be removed by setting


this attribute to NULL.
Aal2Ap

secondarySigLinkId

RNC

Reference to a UniSaalTp MO that is used as a secondary signalling link.


This attribute can be set only when sigLinkId is of type UniSaalTp.

ManagedObject

The reference to the secondary signalling link can be removed by


setting this attribute to NULL.

Aal2Ap

sigLinkId

RBS DUW

Aal2Ap

sigLinkId

RNC

Aal2Ap

timerErq

RBS DUW

Aal2Ap

timerErq

RNC

Reference to a UniSaalTp MO or to an Mtp3bAp MO that provides a


signalling link for the Aal2Ap MO.
Reference to a UniSaalTp MO or to an Mtp3bAp MO that provides a
signalling link for the Aal2Ap MO.

ManagedObject

Timer for Q.2630 establishment requests.

long

5000..30000

5000

5000

long

5000..30000

5000

5000

long

2000..60000

2000

2000

long

2000..60000

2000

2000

ManagedObject

Unit: 1 ms
Timer for Q.2630 establishment requests.
Unit: 1 ms
Aal2Ap

timerRel

RBS DUW

Timer for Q.2630 release requests.


Unit: 1 ms

Aal2Ap

timerRel

RNC

Timer for Q.2630 release requests.

Aal2Ap
Aal2Ap

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal2PathDistributionUnit
Aal2PathDistributionUnit

Aal2PathDistributionUnitId
Aal2PathDistributionUnitId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Unit: 1 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2PathDistributionUnit

aal2PathVccTpList

RBS DUW

Network Parameters

List of references to Aal2PathVccTp MOs.

11 (520)

Aal2PathVccTp

Setting of this attribute removes the current list of Aal2PathVccTp MOs.


The value of "aal2PathId" must be unique amongst all paths within all
Aal2PathDistributionUnit MOs that belong to the same Aal2Ap MO.
If the "aal2pathVccTpList" is changed, all Aal2PathVccTp MOs in the old
list that are not in the new list must have "administrativeState" = LOCKED.

Aal2PathDistributionUnit

aal2PathVccTpList

RNC

List of references to Aal2PathVccTp MOs.

Aal2PathVccTp

Setting of this attribute removes the current list of Aal2PathVccTp


MOs.
The value of "aal2PathId" must be unique amongst all paths within
all Aal2PathDistributionUnit MOs that belong to the same Aal2Ap MO.
If the "aal2pathVccTpList" is changed, all Aal2PathVccTp MOs in
the old list that are not in the new list must have "administrativeState" =
LOCKED.

Aal2PathDistributionUnit

rpuId

RBS DUW

The location of an AAL2 Path Resource Control Program represented by a ReliableProgramUniter


reference to a ReliableProgramUniter MO.
When setting the "rpuId", the "reliableProgramLabel" for the new "rpuId"
must be the same as for the previous "rpuId".
This attribute must be set if the parent Aal2Ap MO has "allocationMode" set
to MANUAL. This attribute must not be set if the parent MO has
"allocationMode" set to AUTOMATIC, but the value of this attribute can still
be read.

Aal2PathDistributionUnit

rpuId

RNC

The location of an AAL2 Path Resource Control Program represented by a ReliableProgramUniter


reference to a ReliableProgramUniter MO.
When setting the "rpuId", the "reliableProgramLabel" for the new
"rpuId" must be the same as for the previous "rpuId".
This attribute must be set if the parent Aal2Ap MO has
"allocationMode" set to MANUAL. This attribute must not be set if the
parent MO has "allocationMode" set to AUTOMATIC, but the value of this
attribute can still be read.

Aal2PathDistributionUnit
Aal2PathDistributionUnit

Prepared: EZIEAGA

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2PathVccTp

aal2PathId

RBS DUW

Network Parameters

Identifies the path in the Q.2630 protocol.

12 (520)

long

1..2147483647

long

1..2147483647

The value must be unique within all Aal2PathDistributionUnit MOs under


the same Aal2Ap MO.
The aal2PathId is used by the AAL2 connection control function in two
AAL2 nodes to uniquely identify an AAL2 path between the two nodes. This
means that the value of the attribute aal2PathId for an AAL2 path must be
the same in each of the two nodes.
In order to set this attribute, the Aal2PathVccTp MO must not be reserved.
If an attempt is made when the Aal2PathVccTp MO is reserved, an
IsReservedCanNotSetPathId exception is thrown.
Setting of this attribute does not have any effect until the action addPath in
the Aal2PathDistributionUnit MO is called, adding this MO to the list of
Aal2PathVccTp MOs.
Aal2PathVccTp

aal2PathId

RNC

Identifies the path in the Q.2630 protocol.


The value must be unique within all Aal2PathDistributionUnit MOs
under the same Aal2Ap MO.
The aal2PathId is used by the AAL2 connection control function in
two AAL2 nodes to uniquely identify an AAL2 path between the two nodes.
This means that the value of the attribute aal2PathId for an AAL2 path
must be the same in each of the two nodes.
In order to set this attribute, the Aal2PathVccTp MO must not be
reserved. If an attempt is made when the Aal2PathVccTp MO is reserved,
an IsReservedCanNotSetPathId exception is thrown.
Setting of this attribute does not have any effect until the action
addPath in the Aal2PathDistributionUnit MO is called, adding this MO to the
list of Aal2PathVccTp MOs.

Aal2PathVccTp

aal2PathOwner

RBS DUW

Indicates whether this AAL2 Path VCC Termination Point is considered to


be the owner of the AAL2 Path in order to decide the channel selection
procedure in the Q.2630 protocol.

boolean

This MO must be unreserved before modifying this attribute.


Setting of this attribute does not have any effect until the action addPath in
the Aal2PathDistributionUnit MO is called, adding this MO to the list of
Aal2PathVccTp MOs.
Lock before modify: Yes
Aal2PathVccTp

aal2PathOwner

RNC

Indicates whether this AAL2 Path VCC Termination Point is considered to


be the owner of the AAL2 Path in order to decide the channel selection
procedure in the Q.2630 protocol.

boolean

This MO must be unreserved before modifying this attribute.


Setting of this attribute does not have any effect until the action
addPath in the Aal2PathDistributionUnit MO is called, adding this MO to the
list of Aal2PathVccTp MOs.
Lock before modify: Yes
Aal2PathVccTp
Aal2PathVccTp

Prepared: EZIEAGA

Aal2PathVccTpId
Aal2PathVccTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

13 (520)

Aal2PathVccTp

aal2QoSAvailableProfiles

RBS DUW

Specifies which QoS class can be supported by this MO.

SupportedQoSClasses

NO_CLASS_SUPPORTED = 0
CLASS_A = 1
CLASS_B = 2
CLASS_A_B = 3
CLASS_C = 4
CLASS_A_C = 5
CLASS_B_C = 6
CLASS_A_B_C = 7
CLASS_D = 8
CLASS_A_D = 9
CLASS_B_D = 10
CLASS_A_B_D = 11
CLASS_C_D = 12
CLASS_A_C_D = 13
CLASS_B_C_D = 14
CLASS_A_B_C_D = 15

CLASS_A_B_C_D See CPI


(15)

Aal2PathVccTp

aal2QoSAvailableProfiles

RNC

Specifies which QoS class can be supported by this MO.

SupportedQoSClasses

NO_CLASS_SUPPORTED = 0
CLASS_A = 1
CLASS_B = 2
CLASS_A_B = 3
CLASS_C = 4
CLASS_A_C = 5
CLASS_B_C = 6
CLASS_A_B_C = 7
CLASS_D = 8
CLASS_A_D = 9
CLASS_B_D = 10
CLASS_A_B_D = 11
CLASS_C_D = 12
CLASS_A_C_D = 13
CLASS_B_C_D = 14
CLASS_A_B_C_D = 15

CLASS_A_B_C_D See CPI


(15)

Aal2PathVccTp
Aal2PathVccTp

aal2QoSProfileId
aal2QoSProfileId

RBS DUW
RNC

Reference to an instance of Aal2QosProfile MO.


Reference to an instance of Aal2QosProfile MO.

Aal2QosProfile
Aal2QosProfile

Aal2PathVccTp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

UNLOCKED(1)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

UNLOCKED(1)

When setting the admininstrativeState to SHUTTING_DOWN, 1800


seconds (30 minutes) will elapse before the MO goes into state LOCKED.
Aal2PathVccTp

administrativeState

RNC

The administrative state.


When setting the admininstrativeState to SHUTTING_DOWN, 1800
seconds (30 minutes) will elapse before the MO goes into state LOCKED.

Aal2PathVccTp

alarmReport

RBS DUW

Specifies which type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

Aal2PathVccTp

alarmReport

RNC

Specifies which type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2PathVccTp

availabilityStatus

RBS DUW

Network Parameters

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Aal2PathVccTp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Aal2PathVccTp

continuityCheck

RBS DUW

Specifies whether VC end-to-end continuity check is active.

14 (520)

boolean

Continuity checking means that a cell is sent downstream when no user


cell has been sent for a period of nominally 1 second. Continuity check
both enables generation of continuity check cells as well as detection of
LOC.
Activation/Deactivation should be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Aal2PathVccTp

continuityCheck

RNC

Specifies whether VC end-to-end continuity check is active.

boolean

Continuity checking means that a cell is sent downstream when no


user cell has been sent for a period of nominally 1 second. Continuity
check both enables generation of continuity check cells as well as
detection of LOC.
Activation/Deactivation should be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Aal2PathVccTp

counterActivation

RBS DUW

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has been
used in the PMS interface.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2PathVccTp

counterActivation

RNC

Network Parameters

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

15 (520)

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has
been used in the PMS interface.

Aal2PathVccTp

counterMode

RBS DUW

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Aal2PathVccTp

counterMode

RNC

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Aal2PathVccTp

nomPmBlocksize

RBS DUW

Nominal block size for PM. The minimum number of ATM cells that is sent
before sending a Forward Performance Monitoring (FPM) cell.

AtmNomPmBlkSize

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

Aal2PathVccTp

nomPmBlocksize

RNC

Nominal block size for PM. The minimum number of ATM cells that is sent
before sending a Forward Performance Monitoring (FPM) cell.
Unit: 1 cells

AtmNomPmBlkSize

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

Aal2PathVccTp

operationalState

RBS DUW

The operational state.

OperState

Aal2PathVccTp

operationalState

RNC

The operational state.

OperState

Aal2PathVccTp

remoteBlockingState

RBS DUW

Represents whether this AAL2 Path VCC Termination Point is locked or


unlocked from the remote end.

RemoteBlockingStates

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
UNDEFINED = 0
REMOTELY_UNBLOCKED = 1
REMOTELY_BLOCKED = 2

Aal2PathVccTp

remoteBlockingState

RNC

Represents whether this AAL2 Path VCC Termination Point is locked or


unlocked from the remote end.

RemoteBlockingStates

Aal2PathVccTp
Aal2PathVccTp

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.

ManagedObject
ManagedObject

Aal2PathVccTp

timerCu

RBS DUW

Timer that assures that CPS packets with one or more octets already
packed in the ATM cell, wait at most the duration of timerCu before being
scheduled for transmission.

long

UNDEFINED = 0
REMOTELY_UNBLOCKED = 1
REMOTELY_BLOCKED = 2

1..100

UNDEFINED(0)

UNDEFINED(0)

10

10

Unit: 0.1 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Aal2PathVccTp

timerCu

RNC

Timer that assures that CPS packets with one or more octets already
packed in the ATM cell, wait at most the duration of timerCu before being
scheduled for transmission.

long

Aal2PathVccTp
Aal2PathVccTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal2PathVccTp

vclTpId

RBS DUW

Reference to an instance of VclTp MO.

VclTp

16 (520)
1..100

10 Normally: 10 If core
network use 0.3 ms: 3

Unit: 0.1 ms

In order to set this attribute, the administrativeState of the related physical


port must be LOCKED.
Aal2PathVccTp

vclTpId

RNC

Reference to an instance of VclTp MO.

VclTp

In order to set this attribute, the administrativeState of the related


physical port must be LOCKED.
Aal2QosCodePointProfile
Aal2QosCodePointProfile

Aal2QosCodePointProfileId
Aal2QosCodePointProfileId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal2QosCodePointProfile

qualityOfServiceCodePointA

RBS DUW

The Code Point for Class A.

long

0..255

128

long

0..255

128

long

0..255

129

long

0..255

129

long

0..255

130

long

0..255

130

long

0..255

131

long

0..255

131

Recommended value for Class A, 128.


Aal2QosCodePointProfile

qualityOfServiceCodePointA

RNC

The Code Point for Class A.


Recommended value for Class A, 128.

Aal2QosCodePointProfile

qualityOfServiceCodePointB

RBS DUW

Aal2QosCodePointProfile

qualityOfServiceCodePointB

RNC

The Code Point for Class B.


Recommended value for Class B, 129.
The Code Point for Class B.
Recommended value for Class B, 129.

Aal2QosCodePointProfile

qualityOfServiceCodePointC

RBS DUW

The Code Point for Class C.


Recommended value for Class C, 130.

Aal2QosCodePointProfile

qualityOfServiceCodePointC

RNC

The Code Point for Class C.


Recommended value for Class C, 130.

Aal2QosCodePointProfile

qualityOfServiceCodePointD

RBS DUW

The Code Point for Class D.


Recommended value for Class D, 131.

Aal2QosCodePointProfile

qualityOfServiceCodePointD

RNC

The Code Point for Class D.


Recommended value for Class D, 131.

Aal2QosCodePointProfile
Aal2QosCodePointProfile

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of Aal2Ap MO instances that reserve this MO instance.


Contains a list of Aal2Ap MO instances that reserve this MO instance.

Aal2Ap
Aal2Ap

Aal2QosCodePointProfile
Aal2QosCodePointProfile

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal2QosProfile
Aal2QosProfile

Aal2QosProfileId
Aal2QosProfileId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal2QosProfile
Aal2QosProfile

profileClassA
profileClassA

RBS DUW
RNC

This attribute holds the values applicable for QoS Class A.


This attribute holds the values applicable for QoS Class A.

QoSProfileClassA
QoSProfileClassA

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2QosProfile

profileClassA.boundOnNodeDelay

RBS DUW

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.

Network Parameters

17 (520)

long

0..10000

5000

10000

long

0..10000

5000

10000

long

0..1000000000

500000

500000

long

0..1000000000

500000

500000

Represents the upper bound of the cell loss probability in the current node. long

0..1000000000

500000

500000

0..1000000000

500000

500000

Unit: 1 ms
Aal2QosProfile

profileClassA.boundOnNodeDelay

RNC

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.
Unit: 1 ms

Aal2QosProfile

profileClassA.boundOnProbOfDelay

RBS DUW

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassA.boundOnProbOfDelay

RNC

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassA.boundOnProbOfLoss

RBS DUW

Unit: 1/1000000000
Aal2QosProfile

profileClassA.boundOnProbOfLoss

RNC

Represents the upper bound of the cell loss probability in the current node. long
Unit: 1/1000000000

Aal2QosProfile
Aal2QosProfile

profileClassB
profileClassB

RBS DUW
RNC

This attribute holds the values applicable for QoS Class B.


This attribute holds the values applicable for QoS Class B.

QoSProfileClassB
QoSProfileClassB

Aal2QosProfile

profileClassB.boundOnNodeDelay

RBS DUW

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.

long

0..20000

15000

20000

long

0..20000

15000

20000

long

0..1000000000

500000

500000

long

0..1000000000

500000

500000

Represents the upper bound of the cell loss probability in the current node. long

0..1000000000

500000

500000

0..1000000000

500000

500000

Unit: 1 ms
Aal2QosProfile

profileClassB.boundOnNodeDelay

RNC

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.
Unit: 1 ms

Aal2QosProfile

profileClassB.boundOnProbOfDelay

RBS DUW

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassB.boundOnProbOfDelay

RNC

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassB.boundOnProbOfLoss

RBS DUW

Unit: 1/1000000000
Aal2QosProfile

profileClassB.boundOnProbOfLoss

RNC

Represents the upper bound of the cell loss probability in the current node. long
Unit: 1/1000000000

Aal2QosProfile
Aal2QosProfile

Prepared: EZIEAGA

profileClassC
profileClassC

RBS DUW
RNC

This attribute holds the values applicable for QoS Class C.


This attribute holds the values applicable for QoS Class C.

Date: 2014-05-27
Sheet: 14.0.2

QoSProfileClassC
QoSProfileClassC

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2QosProfile

profileClassC.boundOnNodeDelay

RBS DUW

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.

Network Parameters

18 (520)

long

25000

25000

long

25000

25000

Unit: 1 ms
Aal2QosProfile

profileClassC.boundOnNodeDelay

RNC

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.
Unit: 1 ms

Aal2QosProfile

profileClassC.boundOnProbOfDelay

RBS DUW

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.

long

0..1000000000

1000000000

1000000000

long

0..1000000000

1000000000

1000000000

Represents the upper bound of the cell loss probability in the current node. long

0..1000000000

1000000000

1000000000

0..1000000000

1000000000

1000000000

Unit: 1/1000000000
Aal2QosProfile

profileClassC.boundOnProbOfDelay

RNC

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassC.boundOnProbOfLoss

RBS DUW

Unit: 1/1000000000
Aal2QosProfile

profileClassC.boundOnProbOfLoss

RNC

Represents the upper bound of the cell loss probability in the current node. long
Unit: 1/1000000000

Aal2QosProfile
Aal2QosProfile

profileClassD
profileClassD

RBS DUW
RNC

This attribute holds the values applicable for QoS Class D.


This attribute holds the values applicable for QoS Class D.

QoSProfileClassD
QoSProfileClassD

Aal2QosProfile

profileClassD.boundOnNodeDelay

RBS DUW

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.

long

50000

50000

long

50000

50000

Unit: 1 ms
Aal2QosProfile

profileClassD.boundOnNodeDelay

RNC

The upper bound on the delay (delay=queueing and serving of Aal2


packets in an Aal2 mux + delay on ATM layer) through the current node.
Unit: 1 ms

Aal2QosProfile

profileClassD.boundOnProbOfDelay

RBS DUW

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.

long

1..1000000000

1000000000

1000000000

long

1..1000000000

1000000000

1000000000

Represents the upper bound of the cell loss probability in the current node. long

0..1000000000

1000000000

1000000000

0..1000000000

1000000000

1000000000

Unit: 1/1000000000
Aal2QosProfile

profileClassD.boundOnProbOfDelay

RNC

Represents the upper bound on the probability that the delay in the node
exceeds the delay limit given by the attribute boundOnNodeDelay.
Unit: 1/1000000000

Aal2QosProfile

profileClassD.boundOnProbOfLoss

RBS DUW

Unit: 1/1000000000
Aal2QosProfile

profileClassD.boundOnProbOfLoss

RNC

Represents the upper bound of the cell loss probability in the current node. long
Unit: 1/1000000000

Aal2QosProfile

Prepared: EZIEAGA

reservedBy

RBS DUW

Contains a list of Aal2PathVccTp MO instances that reserve this MO


instance.

Date: 2014-05-27
Sheet: 14.0.2

Aal2PathVccTp

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Aal2QosProfile

reservedBy

RNC

Contains a list of Aal2PathVccTp MO instances that reserve this MO


instance.

Aal2PathVccTp

Aal2QosProfile
Aal2QosProfile

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal2RoutingCase
Aal2RoutingCase

Aal2RoutingCaseId
Aal2RoutingCaseId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal2RoutingCase

numberDirection

RBS DUW

Defines the possible set of AAL type 2 Service Endpoint Addresses (A2EA) string
that match the routing case.

19 (520)

The number direction of a routing case is interpreted as all AAL type 2


Service Endpoint Addresses starting with the string of numbers defined in
the number direction. For example, the AAL2 End System Addresses
"12340" and "123400" match the number direction "1234".
The AAL2 routing function uses a longest match comparison to select
between routing cases with overlapping number directions. For example,
given two routing cases:
A with the number direction "1234" and B with the number direction
"12345":
- the AAL2 End System Address "12345" is routed using routing case B,
- the AAL type 2 Service Endpoint Addresses "12344" and "12346" are
routed using routing case A.
It is not allowed to use leading zeros when configuring this attribute.
It is not possible to replace an existing routing case by creating routing
cases with number directions that completely overlap the number direction
of the existing routing case.
It is not possible to create two routing cases with the exact same number
directions in a node.
It is possible to create one or more routing cases with number directions
that partially overlap the number direction of an existing routing case.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2RoutingCase

numberDirection

RNC

Network Parameters

20 (520)

Defines the possible set of AAL type 2 Service Endpoint Addresses (A2EA) string
that match the routing case.
The number direction of a routing case is interpreted as all AAL type
2 Service Endpoint Addresses starting with the string of numbers defined in
the number direction. For example, the AAL2 End System Addresses
"12340" and "123400" match the number direction "1234".
The AAL2 routing function uses a longest match comparison to
select between routing cases with overlapping number directions. For
example, given two routing cases:
A with the number direction "1234" and B with the number direction
"12345":
- the AAL2 End System Address "12345" is routed using routing
case B,
- the AAL type 2 Service Endpoint Addresses "12344" and "12346"
are routed using routing case A.
It is not allowed to use leading zeros when configuring this attribute.
It is not possible to replace an existing routing case by creating
routing cases with number directions that completely overlap the number
direction of the existing routing case.
It is not possible to create two routing cases with the exact same
number directions in a node.
It is possible to create one or more routing cases with number
directions that partially overlap the number direction of an existing routing
case.

Aal2RoutingCase

routeList

RBS DUW

An array of alternative routes identified by the concerned Aal2Ap MOs.

Aal2Ap

A routeList can have 0 to 5 Aal2Ap MOs. The Aal2Ap must be unique.


If this attribute is set, the routePriorityList must also be set with the same
number of values (that is, if the routeList contains 3 routes, the
routePriorityList must contain 3 priorities).
The routeList must contain at least one Aal2Ap MO, in order to make the
Aal2RoutingCase available for routing.
Aal2RoutingCase

routeList

RNC

An array of alternative routes identified by the concerned Aal2Ap MOs.

Aal2Ap

A routeList can have 0 to 5 Aal2Ap MOs. The Aal2Ap must be


unique.
If this attribute is set, the routePriorityList must also be set with the
same number of values (that is, if the routeList contains 3 routes, the
routePriorityList must contain 3 priorities).
The routeList must contain at least one Aal2Ap MO, in order to
make the Aal2RoutingCase available for routing.

Aal2RoutingCase

routePriorityList

RBS DUW

A list of all the Aal2Ap priorities.

long

1..5

The priority values can be in the range 1 to 5, one being the highest priority.
The Aal2Aps can have the same priorities.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal2RoutingCase

routePriorityList

RNC

Network Parameters

A list of all the Aal2Ap priorities.

long

21 (520)
1..5

The priority values can be in the range 1 to 5, one being the highest
priority. The Aal2Aps can have the same priorities.
Aal2RoutingCase
Aal2RoutingCase

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal2Sp

a2ea

RBS DUW

An E.164 format number that specifies the AAL type 2 Service Endpoint
Address of the node.

string

Alphabet: 1234567890ABCDEF
It is not allowed to use leading zeros when configuring this attribute.
Dependencies: If the value of afi is 45 (E.164 format), the maximum length
of a2ea is 15 and the Alphabet to use is 1234567890.
Aal2Sp

a2ea

RNC

An E.164 format number that specifies the AAL type 2 Service Endpoint
Address of the node.

string

Alphabet: 1234567890ABCDEF
It is not allowed to use leading zeros when configuring this attribute.
Dependencies: If the value of afi is 45 (E.164 format), the maximum
length of a2ea is 15 and the Alphabet to use is 1234567890.

Aal2Sp
Aal2Sp

Aal2SpId
Aal2SpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal2Sp

afi

RBS DUW

Authority and Format Identifier

string

45

45

string

45

45

Alphabet: 1234567890ABCDEF
The value of this attribute is interpreted as a HEX value.
Aal2Sp

afi

RNC

Authority and Format Identifier


Alphabet: 1234567890ABCDEF
The value of this attribute is interpreted as a HEX value.

Aal2Sp
Aal2Sp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal5TpVccTp
Aal5TpVccTp

Aal5TpVccTpId
Aal5TpVccTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Aal5TpVccTp

alarmReport

RBS DUW

Specifies which type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

Aal5TpVccTp

alarmReport

RNC

Specifies which type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal5TpVccTp

continuityCheck

RBS DUW

Network Parameters

Specifies whether VC end-to-end continuity check is active.

22 (520)

boolean

Continuity checking means that a cell is sent downstream when no user


cell has been sent for a period of nominally 1 second. Continuity check
both enables generation of continuity check cells as well as detection of
LOC.
Activation/Deactivation shall be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
Aal5TpVccTp

continuityCheck

RNC

Specifies whether VC end-to-end continuity check is active.

boolean

Continuity checking means that a cell is sent downstream when no


user cell has been sent for a period of nominally 1 second. Continuity
check both enables generation of continuity check cells as well as
detection of LOC.
Activation/Deactivation shall be done on both ends of a VCC via
management terminal.
Specification: ITU.T rec I.610.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.
Aal5TpVccTp

counterActivation

RBS DUW

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has been
used in the PMS interface.
Aal5TpVccTp

counterActivation

RNC

Indicates whether PM counters are activated for this MO instance, when


MO class activation is used in the Performance Management Service
(PMS) interface.

boolean

If true, this attribute activates all PM counters for this MO instance.


This attribute setting is ignored, when MO instance activation has
been used in the PMS interface.

Aal5TpVccTp

counterMode

RBS DUW

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Aal5TpVccTp

counterMode

RNC

PM mode is set to indicate the type of the performance monitoring mode


used for the F5 PM OAM flow.

AalCounterMode

PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_FPM_
BR(6)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal5TpVccTp

fromUserMaxSduSize

RBS DUW

Network Parameters

The maximum SDU size in number of octets received from the user.

23 (520)

long

1..2048

See CPI

long

1..2048

See CPI

The allowed range for the atribute maxSduSize in UniSaalTp MO and


NniSaalTp MO, is dependent on the processor type:
SP: lowest maxSduSize =1, highest maxSduSize=1600
BP: lowest maxSduSize =1, highest maxSduSize=1600
MP: lowest maxSduSize =1, highest maxSduSize=2048
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
Aal5TpVccTp

fromUserMaxSduSize

RNC

The maximum SDU size in number of octets received from the user.
The allowed range for the atribute maxSduSize in UniSaalTp MO
and NniSaalTp MO, is dependent on the processor type:
SP: lowest maxSduSize =1, highest maxSduSize=1600
BP: lowest maxSduSize =1, highest maxSduSize=1600
MP: lowest maxSduSize =1, highest maxSduSize=2048
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

Aal5TpVccTp

nomPmBlkSize

RBS DUW

Nominal block size for PM. The minimum number of ATM cells that is sent AtmNomPmBlkSize
before sending a Forward Performance Monitoring (FPM) cell.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

Aal5TpVccTp

nomPmBlkSize

RNC

Nominal block size for PM. The minimum number of ATM cells that is sent
before sending a Forward Performance Monitoring (FPM) cell.
Unit: 1 cells
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

AtmNomPmBlkSize

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

Aal5TpVccTp

operationalState

RBS DUW

The operational state.

OperState

Aal5TpVccTp

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Aal5TpVccTp

processorId

RBS DUW

Specifies on what processor the termination point resides. The processor ManagedObject
can either be a board processor or a main processor (PlugInUnit MO) or an
SP processor (Spm MO or PiuDevice MO).
The operationalState of this MO is DISABLED, until this attribute is set.
This attribute can also be set by the "application", that is, the unique
software for the node type, such as RNC, RBS or M-MGW, that uses the
AAL5 transport service. If this attribute is set by the application, this value
overrides any previous value of the attribute.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Aal5TpVccTp

processorId

RNC

Network Parameters

24 (520)

Specifies on what processor the termination point resides. The processor ManagedObject
can either be a board processor or a main processor (PlugInUnit MO) or an
SP processor (Spm MO or PiuDevice MO).
The operationalState of this MO is DISABLED, until this attribute is
set. This attribute can also be set by the "application", that is, the unique
software for the node type, such as RNC, RBS or M-MGW, that uses the
AAL5 transport service. If this attribute is set by the application, this value
overrides any previous value of the attribute.

Aal5TpVccTp
Aal5TpVccTp

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.

ManagedObject
ManagedObject

Aal5TpVccTp

toUserMaxSduSize

RBS DUW

The maximum SDU size in number of octets sent to the user.

long

1..2048

See CPI

long

1..2048

See CPI

The allowed range for the atribute maxSduSize in UniSaalTp MO and


NniSaalTp MO, is dependent on the processor type:
SP: lowest maxSduSize =1, highest maxSduSize=1600
BP: lowest maxSduSize =1, highest maxSduSize=1600
MP: lowest maxSduSize =1, highest maxSduSize=2048
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
Aal5TpVccTp

toUserMaxSduSize

RNC

The maximum SDU size in number of octets sent to the user.


The allowed range for the atribute maxSduSize in UniSaalTp MO
and NniSaalTp MO, is dependent on the processor type:
SP: lowest maxSduSize =1, highest maxSduSize=1600
BP: lowest maxSduSize =1, highest maxSduSize=1600
MP: lowest maxSduSize =1, highest maxSduSize=2048
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

Aal5TpVccTp
Aal5TpVccTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Aal5TpVccTp

vclTpId

RBS DUW

Reference to an instance of VclTp MO.

VclTp

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
Aal5TpVccTp

vclTpId

RNC

Reference to an instance of VclTp MO.

VclTp

Disturbances: Changing lower layer attributes may affect O&M


connectivity, if they are part of the O&M connection.
AddressIPv4
AddressIPv4
AddressIPv4

address
addressIPv4Id
origin

RBS 6401
RBS 6401
RBS 6401

IPv4 address.
string
Value component of the RDN for IPv4 assigned addresses.
string
Specifies who provides this address; if not STATIC, the address field will be OriginIpv4
read-only.

AddressIPv4
AtmCrossConnection
AtmCrossConnection

userLabel
AtmCrossConnectionId
AtmCrossConnectionId

RBS 6401
RBS DUW
RNC

Label for free use.


The value component of the RDN.
The value component of the RDN.

string
string
string

AtmCrossConnection

operationalState

RBS DUW

The operational state.

OperState

AtmCrossConnection

operationalState

RNC

The operational state.

OperState

AtmCrossConnection
AtmCrossConnection

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DHCP = 1
IKEV2 = 2
STATIC = 3

STATIC(3)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
AtmCrossConnection

vclTpAId

RBS DUW

AtmCrossConnection

vclTpAId

RNC

Network Parameters

Identifies the VclTp MO involved in the A side of the cross connection


(which consists of an A and B side).

25 (520)

VclTp

Must not be the same as vclTpBId.


Identifies the VclTp MO involved in the A side of the cross connection
(which consists of an A and B side).

VclTp

Must not be the same as vclTpBId.


AtmCrossConnection

vclTpBId

RBS DUW

AtmCrossConnection

vclTpBId

RNC

Identifies the VclTp MO involved in the B side of the cross connection


(which consists of an A and B side).

VclTp

Must not be the same as vclTpAId.


Identifies the VclTp MO involved in the B side of the cross connection
(which consists of an A and B side).

VclTp

Must not be the same as vclTpAId.


AtmPort
AtmPort

AtmPortId
AtmPortId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

AtmPort

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

AtmPort

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

AtmPort

hecCorrectionMode

RBS DUW

Header Error Correction.

boolean

1 TRUE(1)

Specifies if the ATM Port detects and corrects single bit errors or detects
multiple bit errors in the ATM header.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
AtmPort

hecCorrectionMode

RNC

Network Parameters

Header Error Correction.

26 (520)

boolean

TRUE(1)

Specifies if the ATM Port detects and corrects single bit errors or
detects multiple bit errors in the ATM header.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.
AtmPort

loopbackDetection

RBS DUW

Enables or disables the detection of loopback on the physical path(s) used LoopbackDetection
by AtmPort. If loopback is detected the corresponding physical path is
disabled, and an alarm is issued.

DISABLED = 0
ENABLED = 1

DISABLED(0)

AtmPort

loopbackDetection

RNC

Enables or disables the detection of loopback on the physical path(s) used LoopbackDetection
by AtmPort. If loopback is detected the corresponding physical path is
disabled, and an alarm is issued.

DISABLED = 0
ENABLED = 1

DISABLED(0)

AtmPort

operationalState

RBS DUW

The operational state.

OperState

AtmPort

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

AtmPort
AtmPort

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

AtmPort

uses

RBS DUW

Reference to the physical port, IMA Group or Ds0Bundle used by the ATM ManagedObject
port.
The possible MOs are:
E1PhysPathTerm, J1PhysPathTerm, T1PhysPathTerm, E3PhysPathTerm,
T3PhysPathTerm, Sts3CspeTtp, Sts1SpeTtp, Vc4Ttp, E1Ttp, T1Ttp,
Ds0Bundle and ImaGroup.
If the reference is moved from Ds0Bundle MO then Ds0Bundle would be
deleted automatically.
If the reference is moved from ImaGroup MO then the ImaGroup and all
ImaLinks under it would be deleted automatically.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

AtmPort

uses

RNC

Reference to the physical port, IMA Group or Ds0Bundle used by the ATM ManagedObject
port.
The possible MOs are:
E1PhysPathTerm, J1PhysPathTerm, T1PhysPathTerm,
E3PhysPathTerm, T3PhysPathTerm, Sts3CspeTtp, Sts1SpeTtp, Vc4Ttp,
E1Ttp, T1Ttp, Ds0Bundle and ImaGroup.
If the reference is moved from Ds0Bundle MO then Ds0Bundle
would be deleted automatically.
If the reference is moved from ImaGroup MO then the ImaGroup
and all ImaLinks under it would be deleted automatically.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

AtmPort

valueOfLastCellWithUnexp

RBS DUW

AtmPort

valueOfLastCellWithUnexp

RNC

AtmPort
AtmPort
AtmPort
AtmPort
AtmPort

valueOfLastCellWithUnexp.pti
valueOfLastCellWithUnexp.pti
valueOfLastCellWithUnexp.vci
valueOfLastCellWithUnexp.vci
valueOfLastCellWithUnexp.vpi

RBS DUW
RNC
RBS DUW
RNC
RBS DUW

Prepared: EZIEAGA

This attribute returns the ATM header (VPI, VCI and PTI) of the last
received unexpected cell.
This attribute returns the ATM header (VPI, VCI and PTI) of the last
received unexpected cell.

ValueOfUnex

The ATM header Payload Type Identifier.


The ATM header Payload Type Identifier.
The ATM header Virtual Channel Identifier.
The ATM header Virtual Channel Identifier.
The ATM header Virtual Path Identifier.

long
long
long
long
long

Date: 2014-05-27
Sheet: 14.0.2

ValueOfUnex

0
0
0
0
0

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

27 (520)

AtmPort
AtmTrafficDescriptor
AtmTrafficDescriptor

valueOfLastCellWithUnexp.vpi
AtmTrafficDescriptorId
AtmTrafficDescriptorId

RNC
RBS DUW
RNC

The ATM header Virtual Path Identifier.


The value component of the RDN.
The value component of the RDN.

long
string
string

AtmTrafficDescriptor

egressAtmMcr

RBS DUW

Egress ATM minimum desired cell rate.

long

long

long

long

Only non-negative values are allowed. The attribute is only mandatory


when serviceCategory is UBR+.
AtmTrafficDescriptor

egressAtmMcr

RNC

Egress ATM minimum desired cell rate.


Only non-negative values are allowed. The attribute is only
mandatory when serviceCategory is UBR+.

AtmTrafficDescriptor

egressAtmPcr

RBS DUW

Egress ATM Peak cell rate (cells/s).


Only non-negative values are allowed. This attribute is only mandatory
when serviceCategory is CBR.
When serviceCategory is set to UBR+, egressAtmPcr < egressAtmMcr
disables shaping. egressAtmPcr >= egressAtmMcr enables shaping to the
rate specified.

AtmTrafficDescriptor

egressAtmPcr

RNC

Egress ATM Peak cell rate (cells/s).


Only non-negative values are allowed. This attribute is only
mandatory when serviceCategory is CBR.
When serviceCategory is set to UBR+, egressAtmPcr <
egressAtmMcr disables shaping. egressAtmPcr >= egressAtmMcr enables
shaping to the rate specified.

AtmTrafficDescriptor

egressAtmQos

RBS DUW

Egress ATM quality of service.

AtmQos

CLASS_ONE = 1
CLASS_TWO = 2
CLASS_THREE = 3
CLASS_FOUR = 4

See CPI

AtmQos

CLASS_ONE = 1
CLASS_TWO = 2
CLASS_THREE = 3
CLASS_FOUR = 4

See CPI

This attribute can be set to Class 1 and 2 if attribute serviceCategory is set


to CBR.
This attribute can be set to Class 3 if attribute serviceCategory is set to
UBR+.
This attribute can be set to Class 4 if attribute serviceCategory is set to
UBR.
AtmTrafficDescriptor

egressAtmQos

RNC

Egress ATM quality of service.


This attribute can be set to Class 1 and 2 if attribute
serviceCategory is set to CBR.
This attribute can be set to Class 3 if attribute serviceCategory is
set to UBR+.
This attribute can be set to Class 4 if attribute serviceCategory is
set to UBR.

AtmTrafficDescriptor

ingressAtmMcr

RBS DUW

Ingress minimum desired cell rate (cells/s).

long

long

Only non-negative values are allowed. This attribute is mandatory only


when serviceCategory is UBR+.
AtmTrafficDescriptor

ingressAtmMcr

RNC

Ingress minimum desired cell rate (cells/s).


Only non-negative values are allowed. This attribute is mandatory
only when serviceCategory is UBR+.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
AtmTrafficDescriptor

ingressAtmPcr

RBS DUW

Network Parameters

Ingress ATM Peak cell rate (cells/s).

28 (520)

long

long

Only non-negative values are allowed. The attribute is only mandatory


when serviceCategory is CBR.
AtmTrafficDescriptor

ingressAtmPcr

RNC

Ingress ATM Peak cell rate (cells/s).


Only non-negative values are allowed. The attribute is only
mandatory when serviceCategory is CBR.

AtmTrafficDescriptor

ingressAtmQos

RBS DUW

Ingress ATM quality of service.

AtmQos

CLASS_ONE = 1
CLASS_TWO = 2
CLASS_THREE = 3
CLASS_FOUR = 4

See CPI

AtmQos

CLASS_ONE = 1
CLASS_TWO = 2
CLASS_THREE = 3
CLASS_FOUR = 4

See CPI

This attribute can be set to Class 1 and 2 if attribute serviceCategory is set


to CBR.
This attribute can be set to Class 3 if attribute serviceCategory is set to
UBR+.
This attribute can be set to Class 4 if attribute serviceCategory is set to
UBR.
AtmTrafficDescriptor

ingressAtmQos

RNC

Ingress ATM quality of service.


This attribute can be set to Class 1 and 2 if attribute
serviceCategory is set to CBR.
This attribute can be set to Class 3 if attribute serviceCategory is
set to UBR+.
This attribute can be set to Class 4 if attribute serviceCategory is
set to UBR.

AtmTrafficDescriptor

packetDiscard

RBS DUW

Controls the functions Early Packet Discard (EPD) and Partial Packet
boolean
Discard (PPD) used in AAL5 for traffic classes UBR and UBR+. N.B. should
never be enabled for non-AAL5 traffic.

AtmTrafficDescriptor

packetDiscard

RNC

Controls the functions Early Packet Discard (EPD) and Partial Packet
boolean
Discard (PPD) used in AAL5 for traffic classes UBR and UBR+. N.B. should
never be enabled for non-AAL5 traffic.

AtmTrafficDescriptor
AtmTrafficDescriptor

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

AtmTrafficDescriptor

serviceCategory

RBS DUW

The service category.

ServiceCategory

SERVICE_CATEGORY_CBR = 1
SERVICE_CATEGORY_UBR = 2
SERVICE_CATEGORY_UBR_PLUS
=3

See CPI

AtmTrafficDescriptor

serviceCategory

RNC

The service category.

ServiceCategory

SERVICE_CATEGORY_CBR = 1
SERVICE_CATEGORY_UBR = 2
SERVICE_CATEGORY_UBR_PLUS
=3

See CPI

AtmTrafficDescriptor
AtmTrafficDescriptor

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

ControlInterSwitchLink

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Setting this attribute to LOCKED will suppress CISL alarms. However, this
does not stop the traffic.
ControlInterSwitchLink

administrativeState

RNC

The administrative state.


Setting this attribute to LOCKED will suppress CISL alarms.
However, this does not stop the traffic.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ControlInterSwitchLink

availabilityStatus

RBS DUW

The availability status.

Network Parameters
AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

ControlInterSwitchLink

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

ControlInterSwitchLink
ControlInterSwitchLink
ControlInterSwitchLink

ControlInterSwitchLinkId
ControlInterSwitchLinkId
controlSwitchPort1Ref

RBS DUW
RNC
RBS DUW

The value component of the RDN.


The value component of the RDN.
A reference to one of the MOs to which the CISL is connected. The
referenced MO can be a ControlSwitchPort MO or an EthernetPort MO.

string
string
ControlSwitchPort

ControlInterSwitchLink

controlSwitchPort1Ref

RNC

A reference to one of the MOs to which the CISL is connected. The


referenced MO can be a ControlSwitchPort MO or an EthernetPort MO.

ControlSwitchPort

ControlInterSwitchLink

controlSwitchPort2Ref

RBS DUW

A reference to one of the MOs to which the CISL is connected. The


referenced MO can be a ControlSwitchPort MO or an EthernetPort MO.

ControlSwitchPort

ControlInterSwitchLink

controlSwitchPort2Ref

RNC

A reference to one of the MOs to which the CISL is connected. The


referenced MO can be a ControlSwitchPort MO or an EthernetPort MO.

ControlSwitchPort

ControlInterSwitchLink

operationalState

RBS DUW

The operational state.

OperState

ControlInterSwitchLink

operationalState

RNC

The operational state.

OperState

ControlInterSwitchLink
ControlInterSwitchLink
ControlSwitch

userLabel
userLabel
availabilityStatus

RBS DUW
RNC
RBS DUW

Label for free use.


Label for free use.
The availability status.

string
string
AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

29 (520)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ControlSwitch

availabilityStatus

RNC

The availability status.

Network Parameters

30 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

ControlSwitch

backPlanePortState

RBS DUW

The state of the ethernet back plane ports.

PortState

DISABLED = 0
ENABLED = 1
NOT_CONNECTED = 2
NOT_APPLICABLE = 3
UNKNOWN = 9

ControlSwitch

backPlanePortState

RNC

The state of the ethernet back plane ports.

PortState

DISABLED = 0
ENABLED = 1
NOT_CONNECTED = 2
NOT_APPLICABLE = 3
UNKNOWN = 9

ControlSwitch
ControlSwitch
ControlSwitch

ControlSwitchId
ControlSwitchId
macAddress

RBS DUW
RNC
RBS DUW

The value component of the RDN.


The value component of the RDN.
The Media Access Control address.

string
string
string

It is the mac address used to address the switch for switch management
and by switch control protocols.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
ControlSwitch

macAddress

RNC

The Media Access Control address.

string

It is the mac address used to address the switch for switch


management and by switch control protocols.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
ControlSwitch

operationalState

RBS DUW

The operational state.

OperState

ControlSwitch

operationalState

RNC

The operational state.

OperState

ControlSwitch
ControlSwitch
ControlSwitchPort

userLabel
userLabel
actualSpeedDuplex

RBS DUW
RNC
RBS DUW

Label for free use.


Label for free use.
The mode in which the port is actually operating.

string
string
ActualEthModSpeedDuplex

The value NO_LINK means that the link is physically down.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

NO_LINK = 0
ETH_1_GB_FULL = 1
ETH_10_GB_FULL = 2
ETH_40_GB_FULL = 3
ETH_10_GB_HALF = 4
ETH_40_GB_HALF = 5
ETH_10_MB_HALF = 6
ETH_10_MB_FULL = 7
ETH_100_MB_HALF = 8
ETH_100_MB_FULL = 9
ETH_1_GB_HALF = 10

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ControlSwitchPort

actualSpeedDuplex

RNC

Network Parameters

The mode in which the port is actually operating.

31 (520)

ActualEthModSpeedDuplex

NO_LINK = 0
ETH_1_GB_FULL = 1
ETH_10_GB_FULL = 2
ETH_40_GB_FULL = 3
ETH_10_GB_HALF = 4
ETH_40_GB_HALF = 5
ETH_10_MB_HALF = 6
ETH_10_MB_FULL = 7
ETH_100_MB_HALF = 8
ETH_100_MB_FULL = 9
ETH_1_GB_HALF = 10

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

The value NO_LINK means that the link is physically down.

ControlSwitchPort

availabilityStatus

RBS DUW

The availability status.


Contains details about operationalState.

ControlSwitchPort

availabilityStatus

RNC

The availability status.


Contains details about operationalState.

ControlSwitchPort
ControlSwitchPort
ControlSwitchPort

ControlSwitchPortId
ControlSwitchPortId
operationalState

RBS DUW
RNC
RBS DUW

The value component of the RDN.


The value component of the RDN.
The operational state.

string
string
OperState

ControlSwitchPort

operationalState

RNC

The operational state.

OperState

ControlSwitchPort

portNo

RBS DUW

Physical Port number associated with this MO instance.

long

1..7

long

1..7

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Each ControlSwitchPort instance belonging to the same ControlSwitch


must have a unique portNo, which maps the MO instance to exactly one
physical port.
ControlSwitchPort

portNo

RNC

Physical Port number associated with this MO instance.


Each ControlSwitchPort instance belonging to the same
ControlSwitch must have a unique portNo, which maps the MO instance to
exactly one physical port.

ControlSwitchPort
ControlSwitchPort
ControlSwitchPort
ControlSwitchPort
Dhcp

reservedBy
reservedBy
userLabel
userLabel
DhcpId

RBS DUW
RNC
RBS DUW
RNC
RBS DUW

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.
Label for free use.
Label for free use.
The value component of the RDN.

ManagedObject
ManagedObject
string
string
string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Dhcp

DhcpId

RNC

The value component of the RDN.

Network Parameters

32 (520)

string

It is set automatically when the MO instance is created.


Dhcp

dhcpServerAddresses

RBS DUW

IP addresses to the DHCP server, used by the DHCP Relay Agent.

string

Default is an empty array.


Adding and removing addresses are done using the actions,
addDhcpServerAddress() and removeDhcpServerAddress().
Dhcp

dhcpServerAddresses

RNC

IP addresses to the DHCP server, used by the DHCP Relay Agent.

string

Default is an empty array.


Adding and removing addresses are done using the actions,
addDhcpServerAddress() and removeDhcpServerAddress().
Dhcp
Dhcp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

DnsClient
DnsClient
Ds0Bundle

dnsClientId
serverAddress
availabilityStatus

RBS 6401
RBS 6401
RBS DUW

The local part of the RDN.


The address of the dns server.
The availability status.

string
string
AvailabilityStatus

It contains details about operationalState.

Ds0Bundle

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.

Ds0Bundle
Ds0Bundle

Prepared: EZIEAGA

Ds0BundleId
Ds0BundleId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ds0Bundle

listOfTimeSlots

RBS DUW

Network Parameters

The list gives the time slots (within ATM traffic fraction) that are to be
allocated to the DS0 Bundle.

33 (520)

long

0..31

long

0..31

When a DS0 Bundle is contained by an E1PhysPathTerm, the slots that


can be placed in this list are 1 to 31.
When a DS0 Bundle is contained by a J1PhysPathTerm, the slots that can
be placed in this list are 1 to 24.
When a DS0 Bundle is contained by a T1PhysPathTerm, the slots that can
be placed in this list are 1 to 24.
When a DS0 Bundle is contained by an E1Ttp, the slots that can be placed
in this list are 1 to 31.
When a DS0 Bundle is contained by a T1Ttp, the slots that can be placed
in this list are 1 to 24.
When a DS0 Bundle is contained by a HgTtp, the slots that can be placed
in this list are 1 to 6.
The same timeslot cannot appear more than once in the list. If an
E1/J1/T1PhysPathTerm MP contains more than one DS0 Bundle, the
listOfTimeSlots for the DS0 Bundle must be mutually exclusive, that is,
slots in one list cannot be used in another list.
If the DS0 Bundle is used for carrying SS7 traffic, that is if the DS0 Bundle
is reserved by an Mtp2TpAnsi, Mtp2TpItu or Mtp2TpChina, the
listOfTimeSlots can contain only one time slot.
MinimumLength: 1

Ds0Bundle

listOfTimeSlots

RNC

The list gives the time slots (within ATM traffic fraction) that are to be
allocated to the DS0 Bundle.
When a DS0 Bundle is contained by an E1PhysPathTerm, the slots
that can be placed in this list are 1 to 31.
When a DS0 Bundle is contained by a J1PhysPathTerm, the slots
that can be placed in this list are 1 to 24.
When a DS0 Bundle is contained by a T1PhysPathTerm, the slots
that can be placed in this list are 1 to 24.
When a DS0 Bundle is contained by an E1Ttp, the slots that can be
placed in this list are 1 to 31.
When a DS0 Bundle is contained by a T1Ttp, the slots that can be
placed in this list are 1 to 24.
When a DS0 Bundle is contained by a HgTtp, the slots that can be
placed in this list are 1 to 6.
The same timeslot cannot appear more than once in the list. If an
E1/J1/T1PhysPathTerm MP contains more than one DS0 Bundle, the
listOfTimeSlots for the DS0 Bundle must be mutually exclusive, that is,
slots in one list cannot be used in another list.
If the DS0 Bundle is used for carrying SS7 traffic, that is if the DS0
Bundle is reserved by an Mtp2TpAnsi, Mtp2TpItu or Mtp2TpChina, the
listOfTimeSlots can contain only one time slot.
MinimumLength: 1

Ds0Bundle

operationalState

RBS DUW

The operational state.

OperState

Ds0Bundle

operationalState

RNC

The operational state.

OperState

Ds0Bundle
Ds0Bundle

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.

ManagedObject
ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ds0Bundle

tdmMode

RBS DUW

Network Parameters

The state of tdmMode.

34 (520)

boolean

true - enabled.
false - disabled.
Ds0Bundle

tdmMode

RNC

The state of tdmMode.

boolean

true - enabled.
false - disabled.
Ds0Bundle
Ds0Bundle

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

DscpGroup
DscpGroup
DscpGroup

DscpGroupId
DscpGroupId
dscpValues

RBS DUW
RNC
RBS DUW

The value component of the RDN.


string
The value component of the RDN.
string
An array where each DSCP decimal codepoint value (0-63) in the group is long
set.

0..63

One DSCP value can only be set once and at least one value must be set.
MinimumLength: 1
DscpGroup

dscpValues

RNC

An array where each DSCP decimal codepoint value (0-63) in the group is long
set.

0..63

One DSCP value can only be set once and at least one value must
be set.
MinimumLength: 1
DscpGroup

samplingInterval

RBS DUW

The time interval between consecutive DSCP aggregation group usage


measurements of all DDM counters for this MO.

long

10..10 30..30
60..60 300..300

300

long

10..10 30..30
60..60 300..300

300

The 10 s sampling interval is not supported if the ROP is 60 minutes.


In that case the counters will be disabled and only provide -2 values.
DscpGroup

samplingInterval

RNC

The time interval between consecutive DSCP aggregation group usage


measurements of all DDM counters for this MO.
The 10 s sampling interval is not supported if the ROP is 60
minutes.
In that case the counters will be disabled and only provide -2
values.

DscpGroup
DscpGroup
Dst
Dst
E1PhysPathTerm

userLabel
userLabel
dst
dstId
administrativeState

RBS DUW
RNC
RBS 6401
RBS 6401
RBS DUW

Label for free use.


Label for free use.
IPv4 destination prefix for the route.
Value component of the RDN for IPv4DstNetw.
The administrative state.

string
string
string
string
AdmState

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
E1PhysPathTerm

administrativeState

RNC

The administrative state.

AdmState

Disturbances: Changing lower layer attributes may affect O&M


connectivity, if they are part of the O&M connection.
E1PhysPathTerm

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

true - reporting enabled.


false - reporting disabled.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E1PhysPathTerm

aisReporting

RNC

Network Parameters

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

35 (520)

boolean

true - reporting enabled.


false - reporting disabled.
E1PhysPathTerm

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

Crc4Mode

OFF = 0
ON = 1
AUTOMATIC = 2

ON(1)

ON(1)

Crc4Mode

OFF = 0
ON = 1
AUTOMATIC = 2

ON(1)

ON(1)

It contains details about operationalState.

E1PhysPathTerm

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

E1PhysPathTerm

crc4Mode

RBS DUW

Indicates whether the E1 uses Cyclical Redundancy Check (CRC) 4


framing.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

E1PhysPathTerm

crc4Mode

RNC

Indicates whether the E1 uses Cyclical Redundancy Check (CRC) 4


framing.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

E1PhysPathTerm

degDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

2..10

0..100

30

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
E1PhysPathTerm

degDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

E1PhysPathTerm

degDegThr

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

Unit: 1 %
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E1PhysPathTerm

degDegThr

RNC

Network Parameters

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

36 (520)
0..100

30

Unit: 1 %
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.
E1PhysPathTerm
E1PhysPathTerm

E1PhysPathTermId
E1PhysPathTermId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

E1PhysPathTerm

idlePattern

RBS DUW

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but setting


up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED -> A_LAW.

E1PhysPathTerm

idlePattern

RNC

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.
Changing from A_LAW or U_LAW to UNDEFINED is allowed, but
setting up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED ->
A_LAW.

E1PhysPathTerm
E1PhysPathTerm

lineNo
lineNo

RBS DUW
RNC

The line number on the board.


The line number on the board.

long
long

E1PhysPathTerm

loopback

RBS DUW

The loopback state of this physical path termination.

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

The attribute administrativeState must be set to LOCKED when setting the


attribute loopback.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
E1PhysPathTerm

loopback

RNC

The loopback state of this physical path termination.


The attribute administrativeState must be set to LOCKED when
setting the attribute loopback.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

E1PhysPathTerm

operationalState

RBS DUW

The operational state.

OperState

E1PhysPathTerm

operationalState

RNC

The operational state.

OperState

E1PhysPathTerm

rdiReporting

RBS DUW

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

1..8
1..8

true - reporting enabled.


false - reporting disabled.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E1PhysPathTerm

rdiReporting

RNC

Network Parameters

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

37 (520)

boolean

true - reporting enabled.


false - reporting disabled.
E1PhysPathTerm
E1PhysPathTerm

reservedByImaLink
reservedByImaLink

RBS DUW
RNC

The identity of the ImaLink MO that reserves this MO instance.


The identity of the ImaLink MO that reserves this MO instance.

ImaLink
ImaLink

E1PhysPathTerm

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

E1PhysPathTerm

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

E1PhysPathTerm
E1PhysPathTerm

reservedByTraffic
reservedByTraffic

RBS DUW
RNC

The identity of the AtmPort MO that reserves this MO instance.


The identity of the AtmPort MO that reserves this MO instance.

AtmPort
AtmPort

E1PhysPathTerm

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
E1PhysPathTerm

shutDownTimeout

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

E1PhysPathTerm
E1PhysPathTerm

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

E1Ttp

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
E1Ttp

aisReporting

RNC

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
E1Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E1Ttp

availabilityStatus

RNC

Network Parameters

The availability status.

38 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

E1Ttp

crc4Mode

RBS DUW

Indicates whether the E1 uses Cyclical Redundancy Check (CRC) 4


framing.

Crc4Mode

OFF = 0
ON = 1
AUTOMATIC = 2

ON(1)

ON(1)

E1Ttp

crc4Mode

RNC

Indicates whether the E1 uses Cyclical Redundancy Check (CRC) 4


framing.

Crc4Mode

OFF = 0
ON = 1
AUTOMATIC = 2

ON(1)

ON(1)

E1Ttp

degDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

E1Ttp

degDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

E1Ttp

degDegThr

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

E1Ttp

degDegThr

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

E1Ttp

E1TtpId

RBS DUW

The value component of the RDN.

Unit: 1 %

Unit: 1 %
string

It is set automatically when the MO instance is created.


E1Ttp

E1TtpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


E1Ttp

idlePattern

RBS DUW

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but setting


up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED -> A_LAW.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E1Ttp

idlePattern

RNC

Network Parameters

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

39 (520)
UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but


setting up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED ->
A_LAW.

E1Ttp

operationalState

RBS DUW

The operational state.

OperState

E1Ttp

operationalState

RNC

The operational state.

OperState

E1Ttp

rdiReporting

RBS DUW

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0

true - reporting enabled.


false - reporting disabled.
E1Ttp

rdiReporting

RNC

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
E1Ttp
E1Ttp

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

E1Ttp
E1Ttp

reservedByImaLink
reservedByImaLink

RBS DUW
RNC

The identity of the ImaLink MO that reserves this MO instance.


The identity of the ImaLink MO that reserves this MO instance.

ImaLink
ImaLink

E1Ttp
E1Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

E3PhysPathTerm

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

E3PhysPathTerm

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

E3PhysPathTerm

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
E3PhysPathTerm

aisReporting

RNC

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E3PhysPathTerm

availabilityStatus

RBS DUW

Network Parameters

The availability status.

40 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

E3PhysPathTerm

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

E3PhysPathTerm

degDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

E3PhysPathTerm

degDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

E3PhysPathTerm

degDegThr

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

E3PhysPathTerm

degDegThr

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

E3PhysPathTerm
E3PhysPathTerm

E3PhysPathTermId
E3PhysPathTermId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

E3PhysPathTerm
E3PhysPathTerm

lineNo
lineNo

RBS DUW
RNC

The line number on the board.


The line number on the board.

long
long

E3PhysPathTerm

loopback

RBS DUW

The loopback state of this physical path termination.

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Unit: 1 %

Unit: 1 %

The attribute administrativeState must be set to LOCKED when setting the


attribute loopback.
E3PhysPathTerm

loopback

RNC

The loopback state of this physical path termination.


The attribute administrativeState must be set to LOCKED when
setting the attribute loopback.

E3PhysPathTerm

operationalState

RBS DUW

The operational state.

OperState

E3PhysPathTerm

operationalState

RNC

The operational state.

OperState

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

1..2
1..2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
E3PhysPathTerm

rdiReporting

RBS DUW

Network Parameters

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

41 (520)

boolean

true - reporting enabled.


false - reporting disabled.
E3PhysPathTerm

rdiReporting

RNC

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
E3PhysPathTerm

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

E3PhysPathTerm

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

E3PhysPathTerm
E3PhysPathTerm

reservedByTraffic
reservedByTraffic

RBS DUW
RNC

The identity of the AtmPort MO that reserves this MO instance.


The identity of the AtmPort MO that reserves this MO instance.

AtmPort
AtmPort

E3PhysPathTerm

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
E3PhysPathTerm

shutDownTimeout

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

E3PhysPathTerm
E3PhysPathTerm

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

EquipmentClockReference
EquipmentClockReference
EquipmentClockReference

encapsulation
equipmentClockReferenceId
priority

RBS 6401
RBS 6401
RBS 6401

Specifies the underlying encapsulation of sync reference.


Value component of the RDN.
Specifies the priority of sync reference.

ManagedObject
string
uint8

EquipmentClockReference

referenceStatus

RBS 6401

EthernetLink
EthernetLink

activeMau
activeMau

EthernetLink

availabilityStatus

0..5

Specification: ITU-T G.781


ReferenceStatus

RBS DUW
RNC

Shows the status of sync reference.


The value is decided by the current capability of underlying sync port.
Reference to the active Medium Access Unit (MAU).
Reference to the active Medium Access Unit (MAU).

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

FAILED = 1
SLAVE = 3

FAILED(1)

MediumAccessUnit
MediumAccessUnit
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetLink

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

EthernetLink

availableMaus

RBS DUW

Contains a list of references to all available Medium Access Units (MAUs).

EthernetLink

availableMaus

RNC

Contains a list of references to all available Medium Access Units (MAUs). MediumAccessUnit

EthernetLink
EthernetLink

EthernetLinkId
EthernetLinkId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

EthernetLink

interfaceName

RBS DUW

The interface name.


Dependencies: The value of this attribute can be used as a reference, by
the attributes nodeInterfaceName and nodeIpv6InterfaceName in the Ip
MO.

string

EthernetLink

interfaceName

RNC

The interface name.


Dependencies: The value of this attribute can be used as a
reference, by the attributes nodeInterfaceName and
nodeIpv6InterfaceName in the Ip MO.

string

EthernetLink

ipv4Addresses

RBS DUW

Specifies a list of all IPv4 addresses for the EthernetLink MO.


Ipv4AddressInfo
The first entry of this list can be used as OAM node IP address. See Ip MO
for configuration of OAM node IP address.
The first entry of this list is also represented by the IPv4 address attributes:
broadcastAddress, ipAddress and subnetMask.
The ipAddress in the first element of this attribute cannot be set to 0.0.0.0
or an empty string.
Disturbances: If the network management tool is connected using the
EthernetLink MO, changing the IP address may cause a
disturbance or loss of OAM connectivity, until the node is restarted or the IP
address is changed to the correct
value. If there are any doubts regarding the results of the attribute changes,
it is strongly recommended to
activate the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

EthernetLink

ipv4Addresses

RNC

Specifies a list of all IPv4 addresses for the EthernetLink MO.


Ipv4AddressInfo
The first entry of this list can be used as OAM node IP address.
See Ip MO for configuration of OAM node IP address.
The first entry of this list is also represented by the IPv4 address
attributes: broadcastAddress, ipAddress and subnetMask.
The ipAddress in the first element of this attribute cannot be set to
0.0.0.0 or an empty string.
Disturbances: If the network management tool is connected using
the EthernetLink MO, changing the IP address may cause a disturbance or
loss of OAM connectivity, until the node is restarted or the IP address is
changed to the correct value. If there are any doubts regarding the results
of the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

42 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

MediumAccessUnit

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetLink

ipv4Addresses.broadcastAddress

RBS DUW

Network Parameters

Applicable only if ipAddress is an IPv4 address.

43 (520)

string

The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
EthernetLink

ipv4Addresses.broadcastAddress

RNC

Applicable only if ipAddress is an IPv4 address.

string

The input format for an IPv4 address is four fields of digits,


separated by a dot. Each field consists of one to three digits.
EthernetLink

ipv4Addresses.ipAddress

RBS DUW

Specifies an IPv4 address.

string

The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
EthernetLink

ipv4Addresses.ipAddress

RNC

Specifies an IPv4 address.

string

The input format for an IPv4 address is four fields of digits,


separated by a dot. Each field consists of one to three digits.
EthernetLink
EthernetLink

ipv4Addresses.prefixLength
ipv4Addresses.prefixLength

RBS DUW
RNC

Network Prefix Length.


Network Prefix Length.

long
long

0..30
0..32

EthernetLink

macAddress

RBS DUW

The MAC address is persistently stored in the flash PROM on the MP


where the IP stack resides. It is stored there when the board is
manufactured.

string

EthernetLink

macAddress

RNC

The MAC address is persistently stored in the flash PROM on the MP


where the IP stack resides. It is stored there when the board is
manufactured.

string

EthernetLink

metric

RBS DUW

Specifies the metric of the Ethernet link. The metric value is calculated as
10^8 divided by the link bit speed.

long

1..32767

long

1..32767

For example:
Metric for 10 Mbps Ethernet = 10^8/10^7 = 10
Metric for 100 Mbps or faster Ethernet = 10^8/10^8 = 1
Disturbances: If the network management tool is connected using the
EthernetLink MO, changing the IP address may cause a
disturbance or loss of OAM connectivity, until the node is restarted or the IP
address is changed to the correct
value. If there are any doubts regarding the results of the attribute changes,
it is strongly recommended to
activate the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.
EthernetLink

metric

RNC

Specifies the metric of the Ethernet link. The metric value is calculated as
10^8 divided by the link bit speed.
For example:
Metric for 10 Mbps Ethernet = 10^8/10^7 = 10
Metric for 100 Mbps or faster Ethernet = 10^8/10^8 = 1
Disturbances: If the network management tool is connected using
the EthernetLink MO, changing the IP address may cause a disturbance or
loss of OAM connectivity, until the node is restarted or the IP address is
changed to the correct value. If there are any doubts regarding the results
of the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

44 (520)

EthernetLink

mtuSize

RBS DUW

Maximum transmission Unit for the Ethernet link.


long
Disturbances: If the network management tool is connected using the
EthernetLink MO, changing the IP address may cause a
disturbance or loss of OAM connectivity, until the node is restarted or the IP
address is changed to the correct
value. If there are any doubts regarding the results of the attribute changes,
it is strongly recommended to
activate the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

576..9000

1500

EthernetLink

mtuSize

RNC

Maximum transmission Unit for the Ethernet link.


long
Disturbances: If the network management tool is connected using
the EthernetLink MO, changing the IP address may cause a disturbance or
loss of OAM connectivity, until the node is restarted or the IP address is
changed to the correct value. If there are any doubts regarding the results
of the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

576..9000

1500

EthernetLink

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

This attribute is dependent of the operational states of the underlying


MAUs that represent the Ethernet transceiver function. If there is at least
one operational MAU, the operationalState of EthernetLink is set to
ENABLED.
EthernetLink

operationalState

RNC

The operational state.


This attribute is dependent of the operational states of the
underlying MAUs that represent the Ethernet transceiver function. If there
is at least one operational MAU, the operationalState of EthernetLink is set
to ENABLED.

EthernetLink
EthernetLink

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

EthernetLink
EthernetLink

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

EthernetPort
EthernetPort
EthernetPort

ethernetPortId
macAddress
mtu

RBS 6401
RBS 6401
RBS 6401

Value component of the RDN.


string
The individual MAC address assigned.
string
Specifies maximum transmission unit.
int32
The size (in bytes) of the largest protocol data unit (PDU) that the Ethernet
layer can pass onwards on the Ethernet port.
The PDU includes Ethernet header, Ethertype, Payload and Frame check
sequence.

EthernetPort

operationalState

RBS 6401

Operational state.

OperState

EthernetPort

operOperatingMode

RBS 6401

Operational speed, duplex and master/slave state of the Ethernet port.

EthPortOperatingMode

EthernetPort

userLabel

RBS 6401

Label for free use.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

576..1500

1500

DISABLED = 0
ENABLED = 1
10M_HALF = 2
10M_FULL = 3
100M_HALF = 4
100M_FULL = 5
1G_FULL = 6
""

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitch

availabilityStatus

RBS DUW

Network Parameters

The availability status.

45 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

EthernetSwitch

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

EthernetSwitch

enableVlan

RBS DUW

Specifies whether the switch uses VLAN. If disabled, all VLAN settings for
the EthernetSwitchPort MO are ignored.
Specifies whether the switch uses VLAN. If disabled, all VLAN settings for
the EthernetSwitchPort MO are ignored.

boolean

EthernetSwitch

enableVlan

RNC

EthernetSwitch
EthernetSwitch

EthernetSwitchId
EthernetSwitchId

EthernetSwitch

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

macAddress

RBS DUW

Media Access Control address. It is used for the switch management.


If the board is not available, the attribute has the value
"00:00:00:00:00:00".

string

EthernetSwitch

macAddress

RNC

Media Access Control address. It is used for the switch management.


If the board is not available, the attribute has the value
"00:00:00:00:00:00".

string

EthernetSwitch

operationalState

RBS DUW

The operational state.

OperState

EthernetSwitch

operationalState

RNC

The operational state.

OperState

EthernetSwitch

pbitQueueMap

RBS DUW

Maps the pbit priority according to 802.1Q to switch queues for this port.
Pbit refers to the PCP (Priority Code Point) field in the Ethernet header.
Queue 0 has the lowest priority and queue 3 has the highest priority.

PbitQueue

EthernetSwitch

pbitQueueMap

RNC

Maps the pbit priority according to 802.1Q to switch queues for this port.
Pbit refers to the PCP (Priority Code Point) field in the Ethernet header.
Queue 0 has the lowest priority and queue 3 has the highest priority.

PbitQueue

EthernetSwitch
EthernetSwitch

pbitQueueMap.pbit
pbitQueueMap.pbit

RBS DUW
RNC

The priority bit of the IP packet.


The priority bit of the IP packet.

long
long

0..7
0..7

EthernetSwitch
EthernetSwitch

pbitQueueMap.queue
pbitQueueMap.queue

RBS DUW
RNC

The switch queue.


The switch queue.

long
long

0..3
0..3

EthernetSwitch

reservedBy

RBS DUW

Contains a list of MO instances that reserve this MO instance.

ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

boolean

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

46 (520)

EthernetSwitch

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

EthernetSwitch

untaggedIngressPriority

RBS DUW

All packets that are untagged, when they ingress the internal port, have a
VLAN tag inserted with this priority into the 802.1p value field of the VLAN
tag.

long

0..7

EthernetSwitch

untaggedIngressPriority

RNC

long

0..7

long

1..4095

long

1..4095

If enableVlan is set to false, this attribute is ignored.


All packets that are untagged, when they ingress the internal port, have a
VLAN tag inserted with this priority into the 802.1p value field of the VLAN
tag.
If enableVlan is set to false, this attribute is ignored.
EthernetSwitch

untaggedIngressVid

RBS DUW

All packets that are untagged, when they ingress the internal port, have a
VLAN tag inserted with the specified VLAN id. If this attribute is set to 1,
the default VLAN id is used. If another value is specified, the port must be
a member of the specified VLAN, as defined by the vlanMembership
attribute.

EthernetSwitch

untaggedIngressVid

RNC

All packets that are untagged, when they ingress the internal port, have a
VLAN tag inserted with the specified VLAN id. If this attribute is set to 1,
the default VLAN id is used. If another value is specified, the port must be
a member of the specified VLAN, as defined by the vlanMembership
attribute.

EthernetSwitch
EthernetSwitch

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

EthernetSwitch

vlanMembership

RBS DUW

The VLAN identities supported by the internal port, and the egress untag
behavior for the VLAN on the internal port.

VidInformation

If enableVlan is set to false, this attribute is ignored.

If enableVlan is set to false, this attribute is ignored.

If the vid is set to 0, it means that no VLAN id is specified for the port and
the value specified for egressUntag will be ignored. If vid is set to any
non-zero value, that value will be added as a valid VLAN id for the port. If
the egressUntag flag is set to true, all VLAN tags for the specified vid will
be removed from frames at egress.
The attribute can contain a maximum of 8 VLAN identities, and all entries
must have a unique vid (no entries with duplicate vid values are allowed).

EthernetSwitch

vlanMembership

RNC

The VLAN identities supported by the internal port, and the egress untag
behavior for the VLAN on the internal port.

VidInformation

If the vid is set to 0, it means that no VLAN id is specified for the


port and the value specified for egressUntag will be ignored. If vid is set to
any non-zero value, that value will be added as a valid VLAN id for the port.
If the egressUntag flag is set to true, all VLAN tags for the specified vid will
be removed from frames at egress.
The attribute can contain a maximum of 8 VLAN identities, and all
entries must have a unique vid (no entries with duplicate vid values are
allowed).

EthernetSwitch
EthernetSwitch
EthernetSwitch
EthernetSwitch

Prepared: EZIEAGA

vlanMembership.egressUntag
vlanMembership.egressUntag
vlanMembership.vid
vlanMembership.vid

RBS DUW
RNC
RBS DUW
RNC

Untag at egress
Untag at egress
VLAN identifier
VLAN identifier

boolean
boolean
long
long

Date: 2014-05-27
Sheet: 14.0.2

0
0..4095
0..4095

0
0

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchFabric

EthernetSwitchFabricId

RNC

Network Parameters

The value component of the RDN.

47 (520)

string

It is set automatically when the MO instance is created.


EthernetSwitchFabric

userLabel

RNC

Label for free use.

string

EthernetSwitchingAdm

featureStateL2gp

RBS DUW

ActivationVals

EthernetSwitchingAdm

featureStateL2gp

RNC

EthernetSwitchingAdm

l2gpPathCost

RBS DUW

Specifies if the licensed feature Layer 2 Gateway Port is ACTIVATED or


DEACTIVATED.
Specifies if the licensed feature Layer 2 Gateway Port is ACTIVATED or
DEACTIVATED.
The L2GP path cost.

ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0

ActivationVals

DEACTIVATED(0)
DEACTIVATED(0)

long

1..200000000

80000

long

1..200000000

80000

This attribute is applicable only if l2gpRapidFailover = true.


The L2GP path cost must be equal to, or slightly exceed, the theoretically
most expensive way between two L2GPs. Typically, in a 10 Gbps network,
it is set to 2000 + 2000 + 2000 = 6000.
If the value is set too high, for example 12000 instead of 6000, the
convergence time increases at link failure. If the value is too low, both
L2GPs are opened, but all links between them are blocked by RSTP.
EthernetSwitchingAdm

l2gpPathCost

RNC

The L2GP path cost.


This attribute is applicable only if l2gpRapidFailover = true.
The L2GP path cost must be equal to, or slightly exceed, the
theoretically most expensive way between two L2GPs. Typically, in a 10
Gbps network, it is set to 2000 + 2000 + 2000 = 6000.
If the value is set too high, for example 12000 instead of 6000, the
convergence time increases at link failure. If the value is too low, both
L2GPs are opened, but all links between them are blocked by RSTP.

EthernetSwitchingAdm

l2gpRapidFailover

RBS DUW

Enables decrease of the convergence time at L2GP port failures and


repairs.

boolean

If set to true, the attribute pseudoRootId in all instances of SwitchPortStp


has the same value.
EthernetSwitchingAdm

l2gpRapidFailover

RNC

Enables decrease of the convergence time at L2GP port failures and


repairs.

boolean

If set to true, the attribute pseudoRootId in all instances of


SwitchPortStp has the same value.
EthernetSwitchingAdm

licenseStateL2gp

RBS DUW

EthernetSwitchingAdm

licenseStateL2gp

RNC

EthernetSwitchModule

availabilityStatus

RNC

Indicates whether a valid license key is installed for the feature Layer 2
Gateway Port.
Indicates whether a valid license key is installed for the feature Layer 2
Gateway Port.
The availability status.
It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

StateVals
StateVals
AvailabilityStatus

ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

48 (520)

EthernetSwitchModule

backPlanePortState

RNC

The state of the Ethernet backplane ports, for backplane ports that are not PortState
represented as a reference to an EthernetPort MO;
that is, backplane ports that do not have their own MOs.

DISABLED = 0
ENABLED = 1
NOT_CONNECTED = 2
NOT_APPLICABLE = 3
UNKNOWN = 9

EthernetSwitchModule

EthernetSwitchModuleId

RNC

The value component of the RDN.

string

EthernetSwitchModule

linkAggLinkSelection

RBS DUW

Specifies the link selection method used in a LAG.

LinkSelectionMethod2

MACDA = 0
MACSA = 1
MACDA_PLUS_MACSA = 2
IPDA = 3
IPSA = 4
IPDA_PLUS_IPSA = 5

IPDA_PLUS_IPSA IPDA_PLUS_IPSA(5)
(5)

EthernetSwitchModule

linkAggLinkSelection

RNC

Specifies the link selection method used in a LAG.

LinkSelectionMethod2

MACDA = 0
MACSA = 1
MACDA_PLUS_MACSA = 2
IPDA = 3
IPSA = 4
IPDA_PLUS_IPSA = 5

IPDA_PLUS_IPSA IPDA_PLUS_IPSA(5)
(5)

EthernetSwitchModule

macAddress

RNC

The Media Access Control address.

string

It is the mac address used to address the switch for switch


management and by switch control protocols such as RSTP.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
EthernetSwitchModule

operationalState

RNC

The operational state.

OperState

EthernetSwitchModule

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

EthernetSwitchModule

userLabel

RNC

Label for free use.

string

EthernetSwitchModulePort

actualSpeedDuplex

RNC

The mode in which the port is actually operating.

ActualEthModSpeedDuplex

NO_LINK = 0
ETH_1_GB_FULL = 1
ETH_10_GB_FULL = 2
ETH_40_GB_FULL = 3
ETH_10_GB_HALF = 4
ETH_40_GB_HALF = 5
ETH_10_MB_HALF = 6
ETH_10_MB_FULL = 7
ETH_100_MB_HALF = 8
ETH_100_MB_FULL = 9
ETH_1_GB_HALF = 10

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

The value NO_LINK means that the link is disabled. See the
attribute operatingMode for values of configured speed.

EthernetSwitchModulePort

administrativeState

RNC

The administrative state.


Setting this attribute to LOCKED will suppress port alarms.
However, it does not stop traffic or impact RSTP.

EthernetSwitchModulePort

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1

LOCKED(0)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchModulePort

egressUntagVlanRef

RNC

Network Parameters

Reference to a list of Vlan MOs.

49 (520)

Vlan

If a packet contains a vid with the same value as one of the


referenced Vlan MOs, the packet will be untagged at egress.
If this attribute is set to null, the default value 1 is used for the vid.
The maximum number of Vlan MO references is 256.
Dependency: Any member of this list must also be a member of the
list specified by the attribute vlanRef. Set this attribute in a different
transaction from where the attribute vlanRef is set.
Dependency: If externalPort is set to false, this attribute must not
be set.

EthernetSwitchModulePort

EthernetSwitchModulePortId

RNC

The value component of the RDN.

string

EthernetSwitchModulePort

externalPort

RNC

Specifies if the port is external.

boolean

If set to false, the port is defined to be connected to an ESL.


If set to true, the port is defined to be connected to an external
equipment.
If there is a link failure on an external port where RSTP is
deactivated (by setting the edgePortMode in MO SwitchPortStp to
ADMIN_EDGE_BPDU_FILTER or ADMIN_EDGE_BPDU_GUARD), any
GigaBitEthernet MO connected to this Ethernet switch over the backplane
is redirected to use the backplane to the other Ethernet switch in the
subrack.
Dependencies: egressUntagVlanRef and untaggedIngressVlanRef
must be set to NULL first, before setting this attribute to false.

EthernetSwitchModulePort

lagRef

RBS DUW

Reference to an instance of a Lag MO.

Lag

Specifies which LAG this port belongs to.


All ports in a LAG must fulfill the following conditions:
- they must have identical configuration
- they must be of the same physical type
- they must belong to the same Ethernet switch, that is, have the same
instance of EthernetSwitchModule MO as parent.
There can also exist HW specific restrictions, with respect to the number of
allowed ports in a LAG and how the ports may be paired together. For
details, see the description of the relevant board.
EthernetSwitchModulePort

lagRef

RNC

Reference to an instance of a Lag MO.

Lag

Specifies which LAG this port belongs to.


All ports in a LAG must fulfill the following conditions:
- they must have identical configuration
- they must be of the same physical type
- they must belong to the same Ethernet switch, that is, have the
same instance of EthernetSwitchModule MO as parent.
There can also exist HW specific restrictions, with respect to the
number of allowed ports in a LAG and how the ports may be paired
together. For details, see the description of the relevant board.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchModulePort

operatingMode

RNC

Network Parameters

Contains the configured speed duplex for the port.

50 (520)

EthModOperatingMode

If the port is a member of a LAG, that is if lagRef is set, this


attribute cannot be changed.
EthernetSwitchModulePort

operatingMode.autoNegotiation

RNC

boolean

RNC

See the descriptions of the relevant boards for the supported speeds and
autonegotiation modes.
Specifies the operating speed for this port.

EthernetSwitchModulePort

operatingMode.configuredSpeedDuplex

EthernetSwitchModulePort

0 FALSE(0)

EthModSpeedDuplex

ETH_1_GB_FULL = 1
ETH_10_GB_FULL = 2
ETH_40_GB_FULL = 3

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

EthernetSwitchModulePort

pbitQueueMap

RNC

Maps the pbit priority according to 802.1Q to switch queues for this port.
Pbit refers to the PCP (Priority Code Point) field in the Ethernet header.
Queue 0 has the lowest priority and queue 7 has the highest priority.

PbitQueue8

EthernetSwitchModulePort

pbitQueueMap.pbit

RNC

The priority bit of the IP packet.

long

0..7

EthernetSwitchModulePort

pbitQueueMap.queue

RNC

The switch queue.

long

0..7

EthernetSwitchModulePort

portNo

RNC

Physical Port number associated with this MO instance.

long

1..8

ETH_10_GB_FUL ETH_10_GB_FULL(2)
L(2)

Each EthernetSwitchPort instance belonging to the same


EthernetSwitch must have a unique portNo, which maps the MO instance
to exactly one physical port.
EthernetSwitchModulePort

remoteFaultIndication

RBS DUW

Enables the function that makes it possible for external equipment to detect RemoteFaultIndication
and act if there is no incoming signal on a port. Such fault cases are
caused by faults in a single optical fiber, leading to a unidirectional fault.

DISABLE = 0
ENABLE = 1

DISABLE(0)

DISABLE = 0
ENABLE = 1

DISABLE(0)

OFF = 0
ON = 1

ON(1)

When this function is enabled and if the incoming signal is lost, the
transmitting side is disabled to inform to the remote end that there is a
failure on this link. The transmitting side is kept down until the receiving
side is repaired.
Two ports connected to each other cannot both have this function enabled
as they would risk to never go up.

EthernetSwitchModulePort

remoteFaultIndication

RNC

Enables the function that makes it possible for external equipment to detect RemoteFaultIndication
and act if there is no incoming signal on a port. Such fault cases are
caused by faults in a single optical fiber, leading to a unidirectional fault.
When this function is enabled and if the incoming signal is lost, the
transmitting side is disabled to inform to the remote end that there is a
failure on this link. The transmitting side is kept down until the receiving
side is repaired.
Two ports connected to each other cannot both have this function
enabled as they would risk to never go up.

EthernetSwitchModulePort

trafficState

RBS DUW

Specifies whether traffic is admitted on this port.

TrafficState

If set to ON, traffic is admitted. If set to OFF, traffic is not admitted and the
physical layer is disabled.
Disturbances: It is strongly recommended to activate the robust rollback
function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchModulePort

trafficState

RNC

Network Parameters

Specifies whether traffic is admitted on this port.

51 (520)

TrafficState

OFF = 0
ON = 1

ON(1)

If set to ON, traffic is admitted. If set to OFF, traffic is not admitted


and the physical layer is disabled.
Disturbances: It is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.
EthernetSwitchModulePort

untaggedIngressPriority

RNC

All packets that ingress the port untagged, will have a VLAN tag inserted
with this priority in the 802.1p value field of the VLAN tag.

long

EthernetSwitchModulePort

untaggedIngressVlanRef

RNC

Reference to a Vlan MO.

Vlan

0..7

In all packets that ingress the ethernet port untagged, a VLAN tag is
inserted, with the vid of the referenced Vlan MO.
If this attribute is set to null, the default value 1 is used for the vid.
Dependency: The port must be a member of the specified VLAN,
that is, the value of this attribute must be a member of the list in the
attribute vlanRef. Set this attribute in a different transaction from where the
attribute vlanRef is set.
Dependency: If externalPort is set to false, this attribute must not
be set.

EthernetSwitchModulePort

userLabel

RNC

Label for free use.

string

EthernetSwitchModulePort

vlanRef

RNC

Reference to a list of Vlan MOs.

Vlan

The referenced instances represent the VLANs that are opened on


this port.
The maximum number of Vlan MO references is 256.
EthernetSwitchPort

actualSpeedDuplex

RBS DUW

The mode, in which the port is actually operating. The value NO_LINK
means that the link is disabled or that autonegotiation is in progress. See
attribute operatingMode for values of autonegotiation and configured
speed.

ActualEthernetSpeedDuplex

NO_LINK = 0
ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

EthernetSwitchPort

actualSpeedDuplex

RNC

The mode, in which the port is actually operating. The value NO_LINK
means that the link is disabled or that autonegotiation is in progress. See
attribute operatingMode for values of autonegotiation and configured
speed.

ActualEthernetSpeedDuplex

NO_LINK = 0
ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

EthernetSwitchPort

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Setting this attribute to LOCKED will suppress port alarms. However, it


does not stop traffic or impact RSTP.
EthernetSwitchPort

administrativeState

RNC

The administrative state.


Setting this attribute to LOCKED will suppress port alarms.
However, it does not stop traffic or impact RSTP.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchPort

availabilityStatus

RBS DUW

Network Parameters

The availability status.

52 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

EthernetSwitchPort

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

EthernetSwitchPort
EthernetSwitchPort

EthernetSwitchPortId
EthernetSwitchPortId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

EthernetSwitchPort

ingressPeakBitrate

RBS DUW

The maximum allowed incoming bit rate on this port.

long

1..1000

1000

1000

long

1..1000

1000

1000

Unit: 1 Mbps
EthernetSwitchPort

ingressPeakBitrate

RNC

The maximum allowed incoming bit rate on this port.


Unit: 1 Mbps

EthernetSwitchPort

operatingMode

RBS DUW

A struct that contains the configured speed duplex for the port, and an
indication of whether autonegotiation is performed.

OperatingMode

If autonegotiation is set to true, it must be set to true for both ports in the
Ethernet link. If autonegotiation is set to false, the speed duplex mode must
be identically set for both ports in the Ethernet link.
EthernetSwitchPort

operatingMode

RNC

A struct that contains the configured speed duplex for the port, and an
indication of whether autonegotiation is performed.

OperatingMode

If autonegotiation is set to true, it must be set to true for both ports


in the Ethernet link. If autonegotiation is set to false, the speed duplex
mode must be identically set for both ports in the Ethernet link.
EthernetSwitchPort

operatingMode.autoNegotiation

RBS DUW

Specifies if autonegotiation is enabled or disabled on this port.

boolean

1 TRUE(1)

Autonegotiation must be enabled for SFP ports and when port speed and
duplex settings are configured as ETH_1000_MB_FULL or
ETH_1000_MB_HALF.
Changing autonegotiation to OFF (manual mode), affects the automatic
MDI/MDI-X configuration, which will change into manual mode as well
(forcing a need to consider whether straight through or crossover cables
shall be used).

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchPort

operatingMode.autoNegotiation

RNC

Specifies if autonegotiation is enabled or disabled on this port.

Network Parameters

53 (520)

boolean

TRUE(1)

Autonegotiation must be enabled for SFP ports and when port


speed and duplex settings are configured as ETH_1000_MB_FULL or
ETH_1000_MB_HALF.
Changing autonegotiation to OFF (manual mode), affects the
automatic MDI/MDI-X configuration, which will change into manual mode
as well (forcing a need to consider whether straight through or crossover
cables shall be used).
EthernetSwitchPort

operatingMode.configuredSpeedDuplex

RBS DUW

If autoNegotiation is false, this attribute specifies the fixed operating mode EthernetSpeedDuplex
for the port. If autoNegotiation is true, it specifies the minimum acceptable
operating mode for the port. If the minimum mode is not achieved, a link
failure alarm is raised on the port.
If ETH_1000_MB_HALF or ETH_1000_MB_FULL is selected,
autoNegotiation must be true.
Selecting ETH_1000_MB_HALF or ETH_1000_MB_FULL when
autoNegotiation is false, will disable the port.

EthernetSwitchPort

operatingMode.configuredSpeedDuplex

RNC

If autoNegotiation is false, this attribute specifies the fixed operating mode EthernetSpeedDuplex
for the port. If autoNegotiation is true, it specifies the minimum acceptable
operating mode for the port. If the minimum mode is not achieved, a link
failure alarm is raised on the port.
If ETH_1000_MB_HALF or ETH_1000_MB_FULL is selected,
autoNegotiation must be true.
Selecting ETH_1000_MB_HALF or ETH_1000_MB_FULL when
autoNegotiation is false, will disable the port.

EthernetSwitchPort

operationalState

RBS DUW

The operational state.

OperState

EthernetSwitchPort

operationalState

RNC

The operational state.

OperState

EthernetSwitchPort

pbitQueueMap

RBS DUW

Maps the pbit priority according to 802.1Q to switch queues for this port.
Pbit refers to the PCP (Priority Code Point) field in the Ethernet header.
Queue 0 has the lowest priority and queue 3 has the highest priority.

PbitQueue

EthernetSwitchPort

pbitQueueMap

RNC

Maps the pbit priority according to 802.1Q to switch queues for this port.
Pbit refers to the PCP (Priority Code Point) field in the Ethernet header.
Queue 0 has the lowest priority and queue 3 has the highest priority.

PbitQueue

EthernetSwitchPort
EthernetSwitchPort

pbitQueueMap.pbit
pbitQueueMap.pbit

RBS DUW
RNC

The priority bit of the IP packet.


The priority bit of the IP packet.

long
long

0..7
0..7

EthernetSwitchPort
EthernetSwitchPort

pbitQueueMap.queue
pbitQueueMap.queue

RBS DUW
RNC

The switch queue.


The switch queue.

long
long

0..3
0..3

EthernetSwitchPort

portNo

RBS DUW

Physical Port number associated with this MO instance.

long

1..7

long

1..7

ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

ETH_10_MB_HAL ETH_10_MB_HALF(1)
F(1)

ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

ETH_10_MB_HAL ETH_10_MB_HALF(1)
F(1)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Each EthernetSwitchPort instance belonging to the same EthernetSwitch


must have a unique portNo, which maps the MO instance to exactly one
physical port.
EthernetSwitchPort

portNo

RNC

Physical Port number associated with this MO instance.


Each EthernetSwitchPort instance belonging to the same
EthernetSwitch must have a unique portNo, which maps the MO instance
to exactly one physical port.

EthernetSwitchPort

sfpInformation

RBS DUW

EthernetSwitchPort

sfpInformation

RNC

Prepared: EZIEAGA

Information about the SFP port. Valid only if the attribute sfpPort is set to
true.
Information about the SFP port. Valid only if the attribute sfpPort is set to
true.

Date: 2014-05-27
Sheet: 14.0.2

SfpInformation
SfpInformation

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

54 (520)

EthernetSwitchPort
EthernetSwitchPort

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

RBS DUW
RNC

The product number of an SFP module.


The product number of an SFP module.

string
string

EthernetSwitchPort

sfpInformation.sfpState

RBS DUW

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

EthernetSwitchPort

sfpInformation.sfpState

RNC

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

EthernetSwitchPort

sfpInformation.sfpType

RBS DUW

The type of SFP.

string

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


EthernetSwitchPort

sfpInformation.sfpType

RNC

The type of SFP.

string

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


EthernetSwitchPort

sfpPort

RBS DUW

Specifies whether the switch port is an SFP port. Autonegotiation must be


configured to true for an SFP port. Otherwise, the port may be disabled.

boolean

EthernetSwitchPort

sfpPort

RNC

Specifies whether the switch port is an SFP port. Autonegotiation must be


configured to true for an SFP port. Otherwise, the port may be disabled.

boolean

EthernetSwitchPort

systemPort

RBS DUW

Specifies whether the switch port is a system (backhaul) port, which carries boolean
traffic to/from the IP interfaces on the board.

The IP interfaces on the board are automatically disabled, any time all
ports designated as system ports on the switch are down. If no port on the
switch is designated as a system port, the IP interfaces on the board are
automatically disabled if all created ports on the board are disabled.
EthernetSwitchPort

systemPort

RNC

Specifies whether the switch port is a system (backhaul) port, which carries boolean
traffic to/from the IP interfaces on the board.
The IP interfaces on the board are automatically disabled, any time
all ports designated as system ports on the switch are down. If no port on
the switch is designated as a system port, the IP interfaces on the board
are automatically disabled if all created ports on the board are disabled.

EthernetSwitchPort

trafficState

RBS DUW

Specifies whether traffic is admitted on this port.

TrafficState

OFF = 0
ON = 1

ON(1)

TrafficState

OFF = 0
ON = 1

ON(1)

If set to ON, traffic is admitted. If set to OFF, traffic is not admitted and the
physical layer is disabled.
Disturbances: It is strongly recommended to activate the robust rollback
function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.
EthernetSwitchPort

trafficState

RNC

Specifies whether traffic is admitted on this port.


If set to ON, traffic is admitted. If set to OFF, traffic is not admitted
and the physical layer is disabled.
Disturbances: It is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

EthernetSwitchPort

untaggedIngressPriority

RBS DUW

All packets that ingress the port untagged, will have a VLAN tag inserted
with this priority in the 802.1p value field of the VLAN tag.

long

0..7

If the attribute enableVlan of the related EthernetSwitch MO is set to false,


this attribute is ignored.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
EthernetSwitchPort

untaggedIngressPriority

RNC

Network Parameters

All packets that ingress the port untagged, will have a VLAN tag inserted
with this priority in the 802.1p value field of the VLAN tag.

55 (520)

long

0..7

long

1..4095

long

1..4095

If the attribute enableVlan of the related EthernetSwitch MO is set


to false, this attribute is ignored.
EthernetSwitchPort

untaggedIngressVid

RBS DUW

All packets that ingress the ethernet port untagged, will have a VLAN tag
inserted with the specified VLAN id. If this attribute is set to 1, the default
VLAN id is used. If another value is specified, the port must be a member
of the specified VLAN as defined by the vlanMembership attribute.
If the attribute enableVlan of the related EthernetSwitch MO is set to false,
this attribute is ignored.

EthernetSwitchPort

untaggedIngressVid

RNC

All packets that ingress the ethernet port untagged, will have a VLAN tag
inserted with the specified VLAN id. If this attribute is set to 1, the default
VLAN id is used. If another value is specified, the port must be a member
of the specified VLAN as defined by the vlanMembership attribute.
If the attribute enableVlan of the related EthernetSwitch MO is set
to false, this attribute is ignored.

EthernetSwitchPort
EthernetSwitchPort

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

EthernetSwitchPort

vlanMembership

RBS DUW

The VLAN identities supported by this port, and the egress untag behavior VidInformation
for the VLAN on this port.
If the vid is set to 0, it means that no VLAN id is specified for the port and
the value specified for egressUntag will be ignored. If vid is set to any nonzero value, that value will be added as a valid VLAN id for the port. If the
egressUntag flag is set to true, all VLAN tags for the specified vid will be
removed from frames at egress.
The attribute can contain a maximum of 256 VLAN identities, and all
entries must have a unique vid (no entries with duplicate vid values are
allowed).

EthernetSwitchPort

vlanMembership

RNC

The VLAN identities supported by this port, and the egress untag behavior VidInformation
for the VLAN on this port.
If the vid is set to 0, it means that no VLAN id is specified for the
port and the value specified for egressUntag will be ignored. If vid is set to
any non-zero value, that value will be added as a valid VLAN id for the port.
If the egressUntag flag is set to true, all VLAN tags for the specified vid will
be removed from frames at egress.
The attribute can contain a maximum of 256 VLAN identities, and
all entries must have a unique vid (no entries with duplicate vid values are
allowed).

EthernetSwitchPort
EthernetSwitchPort
EthernetSwitchPort
EthernetSwitchPort
FastEthernet

vlanMembership.egressUntag
vlanMembership.egressUntag
vlanMembership.vid
vlanMembership.vid
administrativeState

RBS DUW
RNC
RBS DUW
RNC
RNC

Untag at egress
Untag at egress
VLAN identifier
VLAN identifier
The administrative state.

boolean
boolean
long
long
AdmState

Traffic is not stopped if administrativeState is set to LOCKED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

0
0..4095
0..4095

0
0
LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
FastEthernet

availabilityStatus

RNC

Network Parameters

The availability status.

56 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

FastEthernet

defaultRouter

RNC

The IP address of the default router.

string

FastEthernet

FastEthernetId

RNC

The value componenet of the RDN.

string

FastEthernet

macAddress

RNC

The MAC address of the ethernet link.

string

00:00:00:00:00:00

If the board is not available, the attribute has the value


"00:00:00:00:00:00".
FastEthernet

mtu

RNC

The maximum transfer unit.

long

64..1500

FastEthernet

networkPrefixLength

RNC

The subnet mask.

long

0..30

1500

1500

Example: networkPrefixLength = 24, subnet mask is 255.255.255.0


Example: networkPrefixLength = 28, subnet mask is
255.255.255.240
Unit: 1 bits
FastEthernet

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

FastEthernet

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

FastEthernet

subnet

RNC

This attribute contains the subnet address of the FastEthernet MO.

string

FastEthernet

userLabel

RNC

Label for free use.

string

GigaBitEthernet

activeLink

RBS DUW

Indicates the active link.

LinkActive

PRIMARY_ACTIVE = 0
SECONDARY_ACTIVE = 1

PRIMARY_ACTIV
E(0)

LinkActive

PRIMARY_ACTIVE = 0
SECONDARY_ACTIVE = 1

PRIMARY_ACTIV
E(0)

This attribute is only applicable for boards supporting configurable link


redundancy.
GigaBitEthernet

activeLink

RNC

Indicates the active link.


This attribute is only applicable for boards supporting configurable
link redundancy.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

actualSpeedDuplex

RBS DUW

Network Parameters

The mode, in which the port is actually operating.

57 (520)

ActualEthernetSpeedDuplex

NO_LINK = 0
ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

ActualEthernetSpeedDuplex

NO_LINK = 0
ETH_10_MB_HALF = 1
ETH_10_MB_FULL = 2
ETH_100_MB_HALF = 3
ETH_100_MB_FULL = 4
ETH_1000_MB_HALF = 5
ETH_1000_MB_FULL = 6

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

The value NO_LINK means that the link is disabled or that autonegotiation
is in progress.
The following values are possible for this attribute, for electrical interfaces:
- ETH_100_MB_FULL
- ETH_1000_MB_FULL
The following values are possible for this attribute, for optical interfaces:
- ETH_1000_MB_FULL

GigaBitEthernet

actualSpeedDuplex

RNC

The mode, in which the port is actually operating.


The value NO_LINK means that the link is disabled or that
autonegotiation is in progress.
The following values are possible for this attribute, for electrical
interfaces:
- ETH_100_MB_FULL
- ETH_1000_MB_FULL
The following values are possible for this attribute, for optical
interfaces:
- ETH_1000_MB_FULL

GigaBitEthernet

administrativeState

RBS DUW

GigaBitEthernet

administrativeState

RNC

The administrative state.


Traffic is not stopped if administrativeState is set to LOCKED.
The administrative state.
Traffic is not stopped if administrativeState is set to LOCKED.

GigaBitEthernet

autoNegotiation

RBS DUW

Indicates whether auto-negotiation is performed.

boolean

In normal traffic situations this attribute is set to true.


Dependencies: If this attribute is set to true, it must be set to true for the
other port in the Ethernet link. If it is set to false, it must be set to false for
the other port in the Ethernet link.
GigaBitEthernet

autoNegotiation

RNC

Indicates whether auto-negotiation is performed.

boolean

TRUE(1)

In normal traffic situations this attribute is set to true.


Dependencies: If this attribute is set to true, it must be set to true
for the other port in the Ethernet link. If it is set to false, it must be set to
false for the other port in the Ethernet link.
GigaBitEthernet

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

availabilityStatus

RNC

Network Parameters

The availability status.

58 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

GigaBitEthernet

configPbitArp

RBS DUW

Specifies pbit to use for ARP and GratARP.

long

0..7

long

0..7

Priorities according to IEEE 802.1Q. Pbit refers to the PCP (Priority Code
Point) field in the Ethernet header.
GigaBitEthernet

configPbitArp

RNC

Specifies pbit to use for ARP and GratARP.


Priorities according to IEEE 802.1Q. Pbit refers to the PCP (Priority
Code Point) field in the Ethernet header.

GigaBitEthernet

configuredSpeedDuplex

RBS DUW

Specifies the wanted fixed speed for the port.


Dependencies: If autoNegotiation is false, this attribute specifies the fixed
speed for the port. If autoNegotiation is true, it specifies the minimum
acceptable speed for the port. If the minimum mode is not achieved, an
alarm is issued but the port is still enabled.

EthernetSpeedFullDuplex

ETH_100_MB_FULL = 4
ETH_1000_MB_FULL = 6

ETH_1000_MB_F
ULL(6)

EthernetSpeedFullDuplex

ETH_100_MB_FULL = 4
ETH_1000_MB_FULL = 6

ETH_1000_MB_F
ULL(6)

If autoNegotiation is set to false, the speed duplex mode must be


identically set for the ports on both sides of the Ethernet link.
Disturbances: Setting this attribute may cause traffic disturbance.
GigaBitEthernet

configuredSpeedDuplex

RNC

Specifies the wanted fixed speed for the port.


Dependencies: If autoNegotiation is false, this attribute specifies
the fixed speed for the port. If autoNegotiation is true, it specifies the
minimum acceptable speed for the port. If the minimum mode is not
achieved, an alarm is issued but the port is still enabled.
If autoNegotiation is set to false, the speed duplex mode must be
identically set for the ports on both sides of the Ethernet link.
Disturbances: Setting this attribute may cause traffic disturbance.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

defRoutersLinkSwitch

RBS DUW

Network Parameters

Indicates whether link switch, triggered by default router supervision, is


enabled or not.

boolean

59 (520)
0

This attribute is only applicable for boards supporting configurable link


redundancy.
A switch to the secondary link is triggered, if the following conditions are
fulfilled:
- the primary link is active,
- all default routers are down on the primary link for all IpInterface MOs
(with default router supervision),
- at least one default router is up on the secondary link
When at least one of the default routers is up on the primary link, a switchback is triggered after the predefined switch-back timer has elapsed.
After the link switch triggered by the default router supervision is
performed, at least one of the alarms emitted prior to the switch on
IpInterface MOs using this GigaBitEthernet MO will be ceased, as at least
one default router is now reachable on the new active link.
Example of emitted alarm: Contact to Default Router 1 Lost.
There will be no link switch due to default router supervision if any of the
links on the GigaBitEthernet MO is faulty.

GigaBitEthernet

defRoutersLinkSwitch

RNC

Indicates whether link switch, triggered by default router supervision, is


enabled or not.

boolean

This attribute is only applicable for boards supporting configurable


link redundancy.
A switch to the secondary link is triggered, if the following conditions
are fulfilled:
- the primary link is active,
- all default routers are down on the primary link for all IpInterface
MOs (with default router supervision),
- at least one default router is up on the secondary link
When at least one of the default routers is up on the primary link, a
switch-back is triggered after the predefined switch-back timer has elapsed.
After the link switch triggered by the default router supervision is
performed, at least one of the alarms emitted prior to the switch on
IpInterface MOs using this GigaBitEthernet MO will be ceased, as at least
one default router is now reachable on the new active link.
Example of emitted alarm: Contact to Default Router 1 Lost.
There will be no link switch due to default router supervision if any
of the links on the GigaBitEthernet MO is faulty.

GigaBitEthernet

dscpPbitMap

RBS DUW

Specifies the value of the DSCP and corresponding pbit (priority).

DscpPbit

The number of members in this sequence is 64.


All the 64 possible DscpPbit structs must be defined when setting this
attribute. If no values are submitted, the default values from struct DscpPbit
are used.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

dscpPbitMap

RNC

Network Parameters

Specifies the value of the DSCP and corresponding pbit (priority).

60 (520)

DscpPbit

The number of members in this sequence is 64.


All the 64 possible DscpPbit structs must be defined when setting
this attribute. If no values are submitted, the default values from struct
DscpPbit are used.
GigaBitEthernet

dscpPbitMap.dscp

RBS DUW

DSCP - differentiated services code point.

long

0..63

long

0..63

The number of members in this sequence is 64.


GigaBitEthernet

dscpPbitMap.dscp

RNC

DSCP - differentiated services code point.


The number of members in this sequence is 64.

GigaBitEthernet

dscpPbitMap.pbit

RBS DUW

802.1p priorities according to IEEE 8021D:


0 - Best effort
1 - Background
2 - Spare
3 - Excellent effort
4 - Controlled load
5 - Voice, less than 100 ms delay
6 - Voice, less than 10 ms delay
7 - Network control

long

0..7

GigaBitEthernet

dscpPbitMap.pbit

RNC

802.1p priorities according to IEEE 8021D:


0 - Best effort
1 - Background
2 - Spare
3 - Excellent effort
4 - Controlled load
5 - Voice, less than 100 ms delay
6 - Voice, less than 10 ms delay
7 - Network control

long

0..7

GigaBitEthernet

frameFormat

RBS DUW

Ethernet outgoing frame format.

EthFrameFormat

ETHERNET_2_DIX = 0
IEEE_802_3_LLC_SNAP = 1

ETHERNET_2_DI
X(0)

EthFrameFormat

ETHERNET_2_DIX = 0
IEEE_802_3_LLC_SNAP = 1

ETHERNET_2_DI ETHERNET_2_DIX(0)
X(0)

Before changing the value from ETHERNET_2_DIX to


IEEE_802_3_LLC_SNAP, ensure that the attribute mtu of the related
IpInterface MO or Ipv6Interface MO is not higher than 1492. If this is the
case, reduce the mtu to 1492 before changing this attribute.
Disturbances: Setting this attribute may disrupt traffic on peer equipment.
GigaBitEthernet

frameFormat

RNC

Ethernet outgoing frame format.


Before changing the value from ETHERNET_2_DIX to
IEEE_802_3_LLC_SNAP, ensure that the attribute mtu of the related
IpInterface MO or Ipv6Interface MO is not higher than 1492. If this is the
case, reduce the mtu to 1492 before changing this attribute.
Disturbances: Setting this attribute may disrupt traffic on peer
equipment.

GigaBitEthernet
GigaBitEthernet

GigaBitEthernetId
GigaBitEthernetId

RBS DUW
RNC

The value componenet of the RDN.


The value componenet of the RDN.

string
string

GigaBitEthernet

link1State

RBS DUW

Operational state of the link 1.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

Is not relevant if the availabilityStatus is DEPENDENCY_FAILED or


DEPENDENCY_LOCKED.
GigaBitEthernet

link1State

RNC

Operational state of the link 1.


Is not relevant if the availabilityStatus is DEPENDENCY_FAILED or
DEPENDENCY_LOCKED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

link2State

RBS DUW

Network Parameters

Operational state of the link 2.

61 (520)

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

LinkType

FRONT_PORTS = 0
BACKPLANE_PORTS = 1

FRONT_PORTS(0
)

LinkType

FRONT_PORTS = 0
BACKPLANE_PORTS = 1

FRONT_PORTS(0
)

This attribute is applicable only if the board supports configurable link


redundancy.
Is not relevant if the availabilityStatus is DEPENDENCY_FAILED or
DEPENDENCY_LOCKED.
GigaBitEthernet

link2State

RNC

Operational state of the link 2.


This attribute is applicable only if the board supports configurable
link redundancy.
Is not relevant if the availabilityStatus is DEPENDENCY_FAILED or
DEPENDENCY_LOCKED.

GigaBitEthernet

linkType

RBS DUW

Indicates if the GigaBitEthernet link for external traffic is using the front
ports or the backplane ports.
For IP ET boards that have only backplane ports, this attribute must be set
to BACKPLANE_PORTS.
For IP ET boards that have only front ports, this attribute must be set to
FRONT_PORTS.
If the backplane ports are used, the link is a 10G link.

GigaBitEthernet

linkType

RNC

Indicates if the GigaBitEthernet link for external traffic is using the front
ports or the backplane ports.
For IP ET boards that have only backplane ports, this attribute must
be set to BACKPLANE_PORTS.
For IP ET boards that have only front ports, this attribute must be
set to FRONT_PORTS.
If the backplane ports are used, the link is a 10G link.

GigaBitEthernet

macAddressLink1

RBS DUW

The MAC address of link 1.

string

00:00:00:00:00:00

string

00:00:00:00:00:00

string

00:00:00:00:00:00

Note that on some boards, macAddressLink1 will always be used for the
active link.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
GigaBitEthernet

macAddressLink1

RNC

The MAC address of link 1.


Note that on some boards, macAddressLink1 will always be used
for the active link.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".

GigaBitEthernet

macAddressLink2

RBS DUW

The MAC address of link 2.


Note that on some boards, macAddressLink2 will always be used for the
passive link.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
This attribute is applicable only if the board supports configurable link
redundancy.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

macAddressLink2

RNC

Network Parameters

The MAC address of link 2.

62 (520)

string

00:00:00:00:00:00

Note that on some boards, macAddressLink2 will always be used


for the passive link.
If the board is not available, the attribute has the value
"00:00:00:00:00:00".
This attribute is applicable only if the board supports configurable
link redundancy.

GigaBitEthernet

masterMode

RBS DUW

Specifies master/slave mode.


Dependencies: If autoNegotiation is false, this attribute specifies if the link
is in master or slave mode. If autoNegotiaion is true, this attribute is
ignored.

boolean

If masterMode is set to true, it must be set to false for the other port in the
Ethernet link. If masterMode is set to false, it must be set to true for the
other port in the Ethernet link.
GigaBitEthernet

masterMode

RNC

Specifies master/slave mode.


boolean
Dependencies: If autoNegotiation is false, this attribute specifies if
the link is in master or slave mode. If autoNegotiaion is true, this attribute is
ignored.
If masterMode is set to true, it must be set to false for the other port
in the Ethernet link. If masterMode is set to false, it must be set to true for
the other port in the Ethernet link.

GigaBitEthernet

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

GigaBitEthernet

operationalState

RNC

The operational state.

OperState

GigaBitEthernet

portNo

RBS DUW

Port number associated with this MO instance.

long

1..3

long

1..3

This attribute is applicable only on boards where link redundancy is not


supported.
For details regarding port numbering, see the description of the relevant
board.
GigaBitEthernet

portNo

RNC

Port number associated with this MO instance.


This attribute is applicable only on boards where link redundancy is
not supported.
For details regarding port numbering, see the description of the
relevant board.

GigaBitEthernet

primaryLink

RBS DUW

Specifies which link is primary and which is secondary.


This attribute is applicable only on boards where link redundancy is
supported. This also includes boards where link redundancy does not need
to be configured.

LinkPrimary

LINK_ONE_PRIMARY_LINK_TWO_ LINK_ONE_PRIM
SECONDARY = 0
ARY_LINK_TWO_
SECONDARY(0)
LINK_TWO_PRIMARY_LINK_ONE_
SECONDARY = 1

If linkType = FRONT_PORTS then link 1 is the lower port and link 2 is the
upper port.
For details regarding port numbering, see the description of the relevant
board.
If linkType = BACKPLANE_PORTS then link1 is connected to the
EthernetSwitchModule with the lowest slot number in the subrack, and link2
is connected to the EthernetSwitchModule with the highest slot number in
the subrack.
Disturbances: Setting of this attribute may cause traffic disturbance.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
GigaBitEthernet

primaryLink

RNC

Network Parameters

Specifies which link is primary and which is secondary.

LinkPrimary

This attribute is applicable only on boards where link redundancy is


supported. This also includes boards where link redundancy does not need
to be configured.

63 (520)
LINK_ONE_PRIMARY_LINK_TWO_ LINK_ONE_PRIM LINK_ONE_PRIMARY_LIN
SECONDARY = 0
ARY_LINK_TWO_ K_TWO_SECONDARY(0)
SECONDARY(0)
LINK_TWO_PRIMARY_LINK_ONE_
SECONDARY = 1

If linkType = FRONT_PORTS then link 1 is the lower port and link 2


is the upper port.
For details regarding port numbering, see the description of the
relevant board.
If linkType = BACKPLANE_PORTS then link1 is connected to the
EthernetSwitchModule with the lowest slot number in the subrack, and link2
is connected to the EthernetSwitchModule with the highest slot number in
the subrack.
Disturbances: Setting of this attribute may cause traffic disturbance.

GigaBitEthernet

protectiveMode

RBS DUW

Indicates whether a switchover to the secondary link is allowed.

boolean

If configurable link redundancy is supported and this attribute is set to false,


it means that a board with two Ethernet connectors works as if it had one
connector.
This attribute is applicable only if the board supports configurable link
redundancy.
GigaBitEthernet

protectiveMode

RNC

Indicates whether a switchover to the secondary link is allowed.

boolean

TRUE(1)

If configurable link redundancy is supported and this attribute is set


to false, it means that a board with two Ethernet connectors works as if it
had one connector.
This attribute is applicable only if the board supports configurable
link redundancy.
GigaBitEthernet
GigaBitEthernet
GigaBitEthernet

reservedBy
reservedBy
sfpInformation

RBS DUW
RNC
RBS DUW

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.
Information about the SFP port. Valid only if the attribute sfpPort is set to
true.
Information about the SFP port. Valid only if the attribute sfpPort is set to
true.

ManagedObject
ManagedObject
SfpInformation

GigaBitEthernet

sfpInformation

RNC

GigaBitEthernet
GigaBitEthernet

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

RBS DUW
RNC

The product number of an SFP module.


The product number of an SFP module.

string
string

GigaBitEthernet

sfpInformation.sfpState

RBS DUW

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

GigaBitEthernet

sfpInformation.sfpState

RNC

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

GigaBitEthernet

sfpInformation.sfpType

RBS DUW

The type of SFP.

string

SfpInformation

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


GigaBitEthernet

sfpInformation.sfpType

RNC

The type of SFP.

string

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


GigaBitEthernet

Prepared: EZIEAGA

sfpPort

RBS DUW

Specifies if the port is an SFP port. Autonegotiation must be configured to


true for an SFP port. Otherwise, the port may be disabled.

Date: 2014-05-27
Sheet: 14.0.2

boolean

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

64 (520)

GigaBitEthernet

sfpPort

RNC

Specifies if the port is an SFP port. Autonegotiation must be configured to


true for an SFP port. Otherwise, the port may be disabled.

boolean

GigaBitEthernet

shutDownTimeout

RBS DUW

The shutting-down timer. It is used when administrativeState is set to


SHUTTING_DOWN.

long

0..100000

1800

long

0..100000

1800

long

0..100

25

long

0..100

25

long

0..3600

30

long

0..3600

30

This value must be positive.


Unit: 1 s
GigaBitEthernet

shutDownTimeout

RNC

The shutting-down timer. It is used when administrativeState is set to


SHUTTING_DOWN.
This value must be positive.
Unit: 1 s

GigaBitEthernet

statePropagationDelay

RBS DUW

GigaBitEthernet

statePropagationDelay

RNC

GigaBitEthernet

switchBackTimer

RBS DUW

This attribute is used to delay the propagation of fault on both links.


Unit: 1 ds (decisecond)
This attribute is used to delay the propagation of fault on both links.
Unit: 1 ds (decisecond)
The switch-back timer, after the primary link has returned to state
ENABLED (working).

25

This attribute is applicable only on boards where configurable link


redundancy is supported.
The value 0 (zero) means that the system does not switch back from the
secondary link to the primary link. Traffic continues to run on the secondary
link until
- a manual switch is performed, or
- an automatic switch is performed by the Link Switch Supervision Function
(in case of link failure on the secondary link, while the primary link is up).
Unit: 1 s

GigaBitEthernet

switchBackTimer

RNC

The switch-back timer, after the primary link has returned to state
ENABLED (working).

30

This attribute is applicable only on boards where configurable link


redundancy is supported.
The value 0 (zero) means that the system does not switch back
from the secondary link to the primary link. Traffic continues to run on the
secondary link until
- a manual switch is performed, or
- an automatic switch is performed by the Link Switch Supervision
Function (in case of link failure on the secondary link, while the primary link
is up).
Unit: 1 s
GigaBitEthernet
GigaBitEthernet

Prepared: EZIEAGA

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
HgTtp

availabilityStatus

RBS DUW

The availability status.

Network Parameters
AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


(DEGRADED qualifies the operational state ENABLED.)

HgTtp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.
(DEGRADED qualifies the operational state ENABLED.)

HgTtp

hgAisReporting

RBS DUW

Indicates whether the alarm HG Alarm Indication Signal (AIS) is to be


issued.

65 (520)

boolean

true - reporting enabled.


false - reporting disabled.
HgTtp

hgAisReporting

RNC

Indicates whether the alarm HG Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
HgTtp

hgBaisReporting

RBS DUW

Indicates whether the alarm HG Backward Alarm Indication Signal (BAIS) is boolean
to be issued.
true - reporting enabled.
false - reporting disabled.

HgTtp

hgBaisReporting

RNC

Indicates whether the alarm HG Backward Alarm Indication Signal (BAIS) is boolean
to be issued.
true - reporting enabled.
false - reporting disabled.

HgTtp

HgTtpId

RBS DUW

HgTtp

HgTtpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


HgTtp

operationalState

RBS DUW

The operational state.

OperState

HgTtp

operationalState

RNC

The operational state.

OperState

HgTtp

userLabel

RBS DUW

Label for free use.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

66 (520)

HgTtp

userLabel

RNC

Label for free use.

string

Host
Host
ImaGroup
ImaGroup

hostId
userLabel
activeLinks
activeLinks

RBS 6401
RBS 6401
RBS DUW
RNC

Value component of the RDN for Host.


Label for free use.
Number of active links.
Number of active links.

string
string
long
long

ImaGroup

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

ImaGroup

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

ImaGroup
ImaGroup

ImaGroupId
ImaGroupId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

ImaGroup

operationalState

RBS DUW

The operational state.

OperState

ImaGroup

operationalState

RNC

The operational state.

OperState

ImaGroup

physicalPortList

RBS DUW

Contains a list of physical port MOs connected to this ImaGroup MO.

ManagedObject

0
0

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

The physical port MOs can be of type:


- E1PhysPathTerm,
- J1PhysPathTerm,
- T1PhysPathTerm,
- E1Ttp,
- T1Ttp.
Add or remove physical port MOs in one set-operation, not both in the
same set-operation.
MinimumLength: 1
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ImaGroup

physicalPortList

RNC

Network Parameters

Contains a list of physical port MOs connected to this ImaGroup MO.

67 (520)

ManagedObject

The physical port MOs can be of type:


- E1PhysPathTerm,
- J1PhysPathTerm,
- T1PhysPathTerm,
- E1Ttp,
- T1Ttp.
Add or remove physical port MOs in one set-operation, not both in
the same set-operation.
MinimumLength: 1
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.
ImaGroup

requiredNumberOfLinks

RBS DUW

Specifies the number of ImaLinks that needs to be operational in order for long
the complete group to be operational. The bandwidth available for the
AtmPort (and thus for the creation of VP/VC connections) is defined by this
number.

1..28

1..28

Setting the requiredNumberOfLinks to K less than the number of physical


links included in the ImaGroup, reduces the guaranteed bandwidth
available to the AtmPort with the corresponding bandwidth. This will also
have the effect that K link failures can be tolerated.
The bandwith associated with the number of available links in the group
above the required number of links is usable only by UBR or UBR+ VP.
The maximum range of this attribute can vary between the boards. See the
description of the relevant board for details.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

ImaGroup

requiredNumberOfLinks

RNC

Specifies the number of ImaLinks that needs to be operational in order for long
the complete group to be operational. The bandwidth available for the
AtmPort (and thus for the creation of VP/VC connections) is defined by this
number.
Setting the requiredNumberOfLinks to K less than the number of
physical links included in the ImaGroup, reduces the guaranteed bandwidth
available to the AtmPort with the corresponding bandwidth. This will also
have the effect that K link failures can be tolerated.
The bandwith associated with the number of available links in the
group above the required number of links is usable only by UBR or UBR+
VP.
The maximum range of this attribute can vary between the boards.
See the description of the relevant board for details.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

ImaGroup
ImaGroup

reservedBy
reservedBy

RBS DUW
RNC

Contains an AtmPort MO instance that reserves this MO instance.


Contains an AtmPort MO instance that reserves this MO instance.

AtmPort
AtmPort

ImaGroup
ImaGroup

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ImaLink

availabilityStatus

RBS DUW

The availability status.

Network Parameters
AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

ImaLink

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

ImaLink

ImaLinkId

RBS DUW

ImaLink

ImaLinkId

RNC

The value component of the RDN.

68 (520)

string

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


ImaLink

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

If the operationalState is DISABLED, the ImaLink is blocked for traffic.


ImaLink

operationalState

RNC

The operational state.


If the operationalState is DISABLED, the ImaLink is blocked for
traffic.

ImaLink
ImaLink

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

ImaLink

uses

RBS DUW

Reference to the physical port represented by this MO. Can be of types:


- E1PhysPathTerm,
- J1PhysPathTerm,
- T1PhysPathTerm,
- E1Ttp or
- T1Ttp.

ManagedObject

ImaLink

uses

RNC

Reference to the physical port represented by this MO. Can be of types:


- E1PhysPathTerm,
- J1PhysPathTerm,
- T1PhysPathTerm,
- E1Ttp or
- T1Ttp.

ManagedObject

InterfaceIPv4

encapsulation

RBS 6401

The underlying encapsulation.

Encapsulation

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

69 (520)

InterfaceIPv4
InterfaceIPv4
InterfaceIPv4

encapsulation.ref
interfaceIPv4Id
operationalState

RBS 6401
RBS 6401
RBS 6401

The underlying encapsulation.


Value component of the RDN for IPv4 Interface.
Operational state.

ManagedObject
string
OperState

InterfaceIPv4
InternalEthernetPort

userLabel
configPbitArp

RBS 6401
RBS DUW

Label for free use.


Specifies pbit to use for ARP and GratARP.

string
long

0..7

long

0..7

DISABLED = 0
ENABLED = 1

Priorities according to IEEE 802.1Q. Pbit refers to the PCP (Priority Code
Point) field in the Ethernet header.
InternalEthernetPort

configPbitArp

RNC

Specifies pbit to use for ARP and GratARP.


Priorities according to IEEE 802.1Q. Pbit refers to the PCP (Priority
Code Point) field in the Ethernet header.

InternalEthernetPort

dscpPbitMap

RBS DUW

The value of the DSCP and the corresponding pbit (priority).

DscpPbit

The number of members in this sequence is 64.


All 64 possible dscpPbit structs must be defined when setting this attribute.
If no values are set, the default values specified in the table in the dscpPbit
struct are used.
InternalEthernetPort

dscpPbitMap

RNC

The value of the DSCP and the corresponding pbit (priority).

DscpPbit

The number of members in this sequence is 64.


All 64 possible dscpPbit structs must be defined when setting this
attribute. If no values are set, the default values specified in the table in the
dscpPbit struct are used.
InternalEthernetPort

dscpPbitMap.dscp

RBS DUW

InternalEthernetPort

dscpPbitMap.dscp

RNC

DSCP - differentiated services code point.

long

0..63

long

0..63

The number of members in this sequence is 64.


DSCP - differentiated services code point.
The number of members in this sequence is 64.
InternalEthernetPort

dscpPbitMap.pbit

RBS DUW

802.1p priorities according to IEEE 8021D:


0 - Best effort
1 - Background
2 - Spare
3 - Excellent effort
4 - Controlled load
5 - Voice, less than 100 ms delay
6 - Voice, less than 10 ms delay
7 - Network control

long

0..7

InternalEthernetPort

dscpPbitMap.pbit

RNC

802.1p priorities according to IEEE 8021D:


0 - Best effort
1 - Background
2 - Spare
3 - Excellent effort
4 - Controlled load
5 - Voice, less than 100 ms delay
6 - Voice, less than 10 ms delay
7 - Network control

long

0..7

InternalEthernetPort
InternalEthernetPort

ethernetSwitchRef
ethernetSwitchRef

RBS DUW
RNC

Reference to an instance of EthernetSwitch MO.


Reference to an instance of EthernetSwitch MO.

ManagedObject
ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
InternalEthernetPort

frameFormat

RBS DUW

Network Parameters

Ethernet outgoing frame format.

70 (520)

EthFrameFormat

ETHERNET_2_DIX = 0
IEEE_802_3_LLC_SNAP = 1

ETHERNET_2_DI ETHERNET_2_DIX(0)
X(0)

EthFrameFormat

ETHERNET_2_DIX = 0
IEEE_802_3_LLC_SNAP = 1

ETHERNET_2_DI ETHERNET_2_DIX(0)
X(0)

Before changing the value from ETHERNET_2_DIX to


IEEE_802_3_LLC_SNAP, ensure first that the attribute mtu of the
IpInterface is not greater than 1492. If mtu > 1492, reduce it to 1492 before
changing this attribute.
Disturbances: Setting this attribute may disrupt traffic on peer equipment.
InternalEthernetPort

frameFormat

RNC

Ethernet outgoing frame format.


Before changing the value from ETHERNET_2_DIX to
IEEE_802_3_LLC_SNAP, ensure first that the attribute mtu of the
IpInterface is not greater than 1492. If mtu > 1492, reduce it to 1492 before
changing this attribute.
Disturbances: Setting this attribute may disrupt traffic on peer
equipment.

InternalEthernetPort
InternalEthernetPort

InternalEthernetPortId
InternalEthernetPortId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

InternalEthernetPort

macAddress

RBS DUW

Media Access Control address

string

00:00:00:00:00:00

string

00:00:00:00:00:00

If the board is not available, the attribute has the value


"00:00:00:00:00:00".
InternalEthernetPort

macAddress

RNC

Media Access Control address


If the board is not available, the attribute has the value
"00:00:00:00:00:00".

InternalEthernetPort
InternalEthernetPort

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Ip

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Ip

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ip

defDomainName

RBS DUW

Network Parameters

71 (520)

Contains default domain name.


string
If isDefDomainName is set to true, the domain name found in this attribute
is used by the DNS resolver and there is no need to submit the complete
domain name.
If the domain name is for example 'ws5741.uab.ericsson.se', then the
default domain name would be '.uab.ericsson.se'.
If isDefDomainName is set to true, there is no need for using
'.uab.ericsson.se'. If set to false, then the complete domain name has to be
used.
A valid domain name consists of one or more labels separated by dots (".").
Valid characters for a label shall be limited to letters 'a' - 'z', 'A' - 'Z', digits '0'
- '9', the character '-' ("dash").
Character case shall be preserved. Total length of a label shall not exceed
255 characters.
The first and last character in the domain name has to be within the
following alphabet: letters 'a' - 'z', 'A' - 'Z' and digits '0' - '9'.
Specification: RFC 952, 1101 and 1123.

Ip

defDomainName

RNC

Contains default domain name.


string
If isDefDomainName is set to true, the domain name found in this
attribute is used by the DNS resolver and there is no need to submit the
complete domain name.
If the domain name is for example 'ws5741.uab.ericsson.se', then
the default domain name would be '.uab.ericsson.se'.
If isDefDomainName is set to true, there is no need for using
'.uab.ericsson.se'. If set to false, then the complete domain name has to be
used.
A valid domain name consists of one or more labels separated by
dots (".").
Valid characters for a label shall be limited to letters 'a' - 'z', 'A' - 'Z',
digits '0' - '9', the character '-' ("dash").
Character case shall be preserved. Total length of a label shall not
exceed 255 characters.
The first and last character in the domain name has to be within the
following alphabet: letters 'a' - 'z', 'A' - 'Z' and digits '0' - '9'.
Specification: RFC 952, 1101 and 1123.

Ip

dnsServerAddresses

RBS DUW

A list of IP addresses to Domain Name Servers.

string

IPv4 and IPv6 addresses are supported.


The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC4291, chapter 2.2, bullet 1 and 2.
Example:
192.168.33.27
2001:db8:0::1
A maximum of 3 DNS server addresses is supported.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity. If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ip

dnsServerAddresses

RNC

Network Parameters

A list of IP addresses to Domain Name Servers.

72 (520)

string

IPv4 and IPv6 addresses are supported.


The input format for an IPv4 address is four fields of digits,
separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC4291, chapter 2.2, bullet 1 and 2.
Example:
192.168.33.27
2001:db8:0::1
A maximum of 3 DNS server addresses is supported.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity. If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

Ip

dscp

RBS DUW

The DiffServ CodePoint.

long

0..63

long

0..63

The code point values are used by DiffServ enabled hosts and router to
identify different service levels.
When set, the DSCPs are mapped to Per Hop Behaviours (PHB) by
forwarding devices along the path between the source and destination.
PHBs dictates how each packet is handled, that is, what type of service
that is applied to the packet when it is forwarded.
Only traffic originated from the node is tagged with the dscp value. The
CPP based router does not implement functionality for handling different
service levels when routing IP traffic.
Ip

dscp

RNC

The DiffServ CodePoint.


The code point values are used by DiffServ enabled hosts and
router to identify different service levels.
When set, the DSCPs are mapped to Per Hop Behaviours (PHB) by
forwarding devices along the path between the source and destination.
PHBs dictates how each packet is handled, that is, what type of service
that is applied to the packet when it is forwarded.
Only traffic originated from the node is tagged with the dscp value.
The CPP based router does not implement functionality for handling
different service levels when routing IP traffic.

Ip
Ip

icmpRedirect
icmpRedirect

RBS DUW
RNC

Indicates if ICMP redirects is sent out or not.


Indicates if ICMP redirects is sent out or not.

boolean
boolean

Ip
Ip

IpId
IpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Ip

isDefDomainName

RBS DUW

Specifies whether the default domain name is present.

boolean

1 TRUE(1)
TRUE(1)

true - present
false - not present
Ip

isDefDomainName

RNC

Specifies whether the default domain name is present.

boolean

true - present
false - not present

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ip

isRecursiveSearch

RBS DUW

Specifies how the DNS client wants the DNS server do the search for the
IP address in the network .

Network Parameters

73 (520)

boolean

true - recursive search


false - non-recursive search
Ip

isRecursiveSearch

RNC

Specifies how the DNS client wants the DNS server do the search for the
IP address in the network .

boolean

true - recursive search


false - non-recursive search
Ip

isSubDomainName

RBS DUW

Specifies whether to use subsets of the fully qualified domain name to


reach the simple domain name.

boolean

true - use subsets of domain name


false - do not use subsets of domain name
Ip

isSubDomainName

RNC

Specifies whether to use subsets of the fully qualified domain name to


reach the simple domain name.

boolean

true - use subsets of domain name


false - do not use subsets of domain name
Ip

nodeInterfaceName

RBS DUW

The interface name of the link object that determines the OAM IPv4
string
address for the node.
This attribute cannot be set to an empty string.
Dependencies: The value of this attribute is set to the value of the attribute
interfaceName in the EthernetLink MO, or in the IpHostLink MO. The
referenced link MO must exist, and specify the wanted nodeIpv4Address
as the first element of the ipv4addresses attribute.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity or ORB restart. If there are any doubts
regarding the results of the attribute changes, it is strongly recommended
to activate the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

le0

Ip

nodeInterfaceName

RNC

The interface name of the link object that determines the OAM IPv4
address for the node.
This attribute cannot be set to an empty string.
Dependencies: The value of this attribute is set to the value of the
attribute interfaceName in the EthernetLink MO, or in the IpHostLink MO.
The referenced link MO must exist, and specify the wanted
nodeIpv4Address as the first element of the ipv4addresses attribute.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity or ORB restart. If there are any
doubts regarding the results of the attribute changes, it is strongly
recommended to activate the robust rollback function, by setting the
attribute configCountdownActivated on the ConfigurationVersion MO first.

string

le0

Ip
Ip

nodeIpAddress
nodeIpAddress

RBS DUW
RNC

The OAM IPv4 address for the node.


The OAM IPv4 address for the node.

string
string

Ip
Ip

noOfRetrans
noOfRetrans

RBS DUW
RNC

The number of retransmissions.


The number of retransmissions.

long
long

Ip

numberOfLinks

RBS DUW

Indicates the number of links that are configured for the Ip MO.The links
long
are the MOs: EthernetLink, IpAtmLink, IpHostLink and IpAccessHostEt.The
value of numberOfLinks also includes the loopback interface that is not
related to any MO, but is visible in the listRoutes action in MO
IpRoutingTable, for example.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

0..255
0..255

5
5

5
5

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Ip

numberOfLinks

RNC

Indicates the number of links that are configured for the Ip MO.The links
long
are the MOs: EthernetLink, IpAtmLink, IpHostLink and IpAccessHostEt.The
value of numberOfLinks also includes the loopback interface that is not
related to any MO, but is visible in the listRoutes action in MO
IpRoutingTable, for example.

Ip

operationalState

RBS DUW

The operational state.

Ip

operationalState

RNC

74 (520)

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

This attribute is set to ENABLED if at least one link is operational.


The operational state.
This attribute is set to ENABLED if at least one link is operational.

Ip
Ip

reservedBy
reservedBy

RBS DUW
RNC

Contains an Ospf MO instance that reserves this MO instance.


Contains an Ospf MO instance that reserves this MO instance.

ManagedObject
ManagedObject

Ip

retransInterval

RBS DUW

The retransmission interval.

long

0..255

Ip

retransInterval

RNC

long

0..255

long

long

boolean

1 TRUE(1)

Unit: 1 s
The retransmission interval.
Unit: 1 s
Ip

udpChecksumState

RBS DUW

Enables or disables generation of UDP checksum.


0 = disabled
1 = enabled
The UDP checksum is used to verify that the UDP header has not been
damaged during transmission.

Ip

udpChecksumState

RNC

Enables or disables generation of UDP checksum.


0 = disabled
1 = enabled
The UDP checksum is used to verify that the UDP header has not
been damaged during transmission.

Ip

useHostFile

RBS DUW

Specifies if the host file is used. The hostFile is used by the resolver and
chosen as a source of information before querying a DNS server.
true - use the host file
false - do not use the host file
This is an example of the host file:
127.0.0.1 localhost
192.102.73.6 somehost
2001:db8::1 somehost
The file name is hosts and the path is /c/configuration.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity depending on the contents of the hosts file.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ip

useHostFile

RNC

Network Parameters

Specifies if the host file is used. The hostFile is used by the resolver and
chosen as a source of information before querying a DNS server.

75 (520)

boolean

TRUE(1)

true - use the host file


false - do not use the host file
This is an example of the host file:
127.0.0.1 localhost
192.102.73.6 somehost
2001:db8::1 somehost
The file name is hosts and the path is /c/configuration.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity depending on the contents of the
hosts file.
Ip
Ip

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Ip

workingMode

RBS DUW

Specifies if the IP stack in the node works as a combined host/router


WorkingMode
(ROUTER_MODE) or only as a host (HOST_MODE).
Dependencies: If the IpHostLink MO is used, do not set this attribute to
ROUTER_MODE, since routing on incoming OAM traffic is not supported
on this link type.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM routing functionality.If there are any doubts regarding the
results of the attribute changes, it is strongly recommended to activate the
robust rollback function, by setting the attribute configCountdownActivated
on the ConfigurationVersion MO first.

HOST_MODE = 0
ROUTER_MODE = 1

See CPI

Ip

workingMode

RNC

Specifies if the IP stack in the node works as a combined host/router


(ROUTER_MODE) or only as a host (HOST_MODE).
Dependencies: If the IpHostLink MO is used, do not set this
attribute to ROUTER_MODE, since routing on incoming OAM traffic is not
supported on this link type.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM routing functionality. If there are any doubts
regarding the results of the attribute changes, it is strongly recommended
to activate the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

WorkingMode

HOST_MODE = 0
ROUTER_MODE = 1

ROUTER_MODE(1)

IpAccessAutoConfig

IpAccessAutoConfigId

RNC

The value component of the RDN.

string

IpAccessAutoConfig

maxIpAddress

RNC

Maximum IP address

string

The highest value that can be used as host IP address. If


autoConfig=ON for an IP access host, it is not necessary to assign explicitly
an IP address and prefix length to the host. The IP address is assigned by
the Control Plane, based on the identity of IpAccessAutoConfig specified
for the IP access host.
IpAccessAutoConfig

minIpAddress

RNC

Minimum IP address

string

The lowest value that can be used as host IP address. If


autoConfig=ON for an IP access host, it is not necessary to assign explicitly
an IP address and prefix length to the host. The IP address is assigned by
the Control Plane, based on the identity of IpAccessAutoConfig specified
for the IP access host.
IpAccessAutoConfig

nrOfUnusedAdresses

RNC

Number of unused addresses

long

The number of addresses in the range that are not used.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

IpAccessAutoConfig

reservedBy

RNC

Contains a list of MO instances that reserve IP access hosts.

ManagedObject

IpAccessAutoConfig

totalNrOfAddresses

RNC

Total number of addresses in the range.

long

76 (520)

The first address in the range is the same one as the one for
networkAddress.
IpAccessAutoConfig

userLabel

RNC

Label for free use.

string

IpAccessHostEt

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

IpAccessHostEt

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

IpAccessHostEt

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

IpAccessHostEt

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

IpAccessHostEt
IpAccessHostEt

Prepared: EZIEAGA

IpAccessHostEtId
IpAccessHostEtId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostEt

ipAddress

RBS DUW

Network Parameters

The IP address of the host.

77 (520)

string

The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC4291, chapter 2.2, bullet 1 and 2.
The address type for the IPv6 address must be global unicast.
This IP address must be unique with respect to other hosts in the node.
An IPv4 address must belong to the subnet which is indicated in the MO
referenced by ipInterfaceMoRef.
If this MO refers to an IpInterfaceGroup MO, the IP address in this attribute
must:
- be different from the attribute ownIpAddressActive in both the IpInterface
MOs referenced by the IpInterfaceGroup MO.
- belong to the same subnet as the IP interfaces referenced by the
IpInterfaceGroup MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

IpAccessHostEt

ipAddress

RNC

The IP address of the host.

string

The input format for an IPv4 address is four fields of digits,


separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC4291, chapter 2.2, bullet 1 and 2.
This IP address must be unique with respect to other hosts in the
node.
An IPv4 address must belong to the subnet which is indicated in the
MO referenced by ipInterfaceMoRef.
If this MO refers to an IpInterfaceGroup MO, the IP address in this
attribute must:
- be different from the attribute ownIpAddressActive in both the
IpInterface MOs referenced by the IpInterfaceGroup MO.
- belong to the same subnet as the IP interfaces referenced by the
IpInterfaceGroup MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

IpAccessHostEt

ipDefaultTtl

RBS DUW

The default value of the Time-To-Live (TTL) field of the IP header. The
value is inserted into datagrams originating at this host, whenever a TTL
value is not supplied by the transport layer protocol.

IpAccessHostEt

ipDefaultTtl

RNC

The default value of the Time-To-Live (TTL) field of the IP header. The
value is inserted into datagrams originating at this host, whenever a TTL
value is not supplied by the transport layer protocol.

IpAccessHostEt

ipInterfaceMoRef

RBS DUW

For IPv4: Reference to an IpInterface MO or VpnInterface MO, or


IpInterfaceGroup MO.

long

1..255

64

64

long

1..255

64

64

This attribute is not applicable for an IPv6 address.

This attribute is not applicable for an IPv6 address.


ManagedObject

For IPv6: Reference to an Ipv6Interface MO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

IpAccessHostEt

ipInterfaceMoRef

RNC

For IPv4: Reference to an IpInterface MO or VpnInterface MO, or


IpInterfaceGroup MO.

IpAccessHostEt
IpAccessHostEt
IpAccessHostEt

ntpDscp
ntpDscp
ntpServerMode

RBS DUW
RNC
RBS DUW

The DSCP value to be used for outgoing NTP packets.


The DSCP value to be used for outgoing NTP packets.
Specifies whether a host is acting as an NTP server.
Dependencies: This attribute can be set to ENABLED only if the following
conditions apply:
- there is no IpSyncRef MO in the node
- the attribute ipAddress is of type IPv4.

long
long
NtpServerMode

IpAccessHostEt

ntpServerMode

RNC

Specifies whether a host is acting as an NTP server.


Dependencies: This attribute can be set to ENABLED only if the
following conditions apply:
- there is no IpSyncRef MO in the node
- the attribute ipAddress is of type IPv4.

IpAccessHostEt

operationalState

RBS DUW

IpAccessHostEt

operationalState

IpAccessHostEt
IpAccessHostEt
IpAccessHostEt
IpAccessHostEt
IpAccessHostGpb

78 (520)

ManagedObject

For IPv6: Reference to an Ipv6Interface MO.


0..63
0..63

46
46
DISABLED = 0
ENABLED = 1

DISABLED(0)

NtpServerMode

DISABLED = 0
ENABLED = 1

DISABLED(0)

The operational state.

OperState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

reservedBy
reservedBy
userLabel
userLabel
activeGpuId

RBS DUW
RNC
RBS DUW
RNC
RBS DUW

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.
Label for free use.
Label for free use.
Reference to the active GeneralProcessorUnit MO. By default, the
reference is the same as the attribute generalProcessorUnitId. However, a
user of this MO, for example Sctp MO, can set another reference, for
example for redundancy. Then, the instance of the GeneralProcessorUnit
MO defined by the attribute activeGpuId differs from the instance defined
by the attribute generalProcessorUnitId.

ManagedObject
ManagedObject
string
string
ManagedObject

IpAccessHostGpb

activeGpuId

RNC

Reference to the active GeneralProcessorUnit MO. By default, the


ManagedObject
reference is the same as the attribute generalProcessorUnitId. However, a
user of this MO, for example Sctp MO, can set another reference, for
example for redundancy. Then, the instance of the GeneralProcessorUnit
MO defined by the attribute activeGpuId differs from the instance defined
by the attribute generalProcessorUnitId.

IpAccessHostGpb

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

IpAccessHostGpb

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

IpAccessHostGpb

autoConfig

RBS DUW

autoConfig

RNC

ON = 1
OFF = 2
ON = 1
OFF = 2

OFF(2)

IpAccessHostGpb

This attribute specifies whether autoconfiguration for the IP Access Host is AutoConfigurationMode
used.
This attribute specifies whether autoconfiguration for the IP Access Host is AutoConfigurationMode
used.

IpAccessHostGpb

autoConfigIdentity

RBS DUW

IpAccessHostGpb

autoConfigIdentity

RNC

The identity of the IpAccessAutoConfig MO used by this host.

OFF(2)

IpAccessAutoConfig

This attribute is mandatory if autoConfig is set to ON.


The identity of the IpAccessAutoConfig MO used by this host.

IpAccessAutoConfig

This attribute is mandatory if autoConfig is set to ON.


IpAccessHostGpb

autoConfigIdentity2

RBS DUW

The identity of the IpAccessAutoConfig MO used by this host.

IpAccessAutoConfig

This attribute must be set, if autoConfig is set to ON and if the host has two
IP addresses assigned automatically.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostGpb

autoConfigIdentity2

RNC

Network Parameters

The identity of the IpAccessAutoConfig MO used by this host.

79 (520)

IpAccessAutoConfig

This attribute must be set, if autoConfig is set to ON and if the host


has two IP addresses assigned automatically.
IpAccessHostGpb

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

IpAccessHostGpb

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

IpAccessHostGpb

generalProcessorUnitId

RBS DUW

Reference to an instance of GeneralProcessorUnit MO.

GeneralProcessorUnit

Default location of the IP host after a node restart. The location can be
overriden by the value of the attribute activeGpuId.
IpAccessHostGpb

generalProcessorUnitId

RNC

Reference to an instance of GeneralProcessorUnit MO.

GeneralProcessorUnit

Default location of the IP host after a node restart. The location can
be overriden by the value of the attribute activeGpuId.
IpAccessHostGpb

interface1

RBS DUW

Reference to an IpInterface MO, IpInterfaceGroup MO or to a FastEthernet ManagedObject


MO.
If two IP addresses are used, and thus two interfaces, this interface is for
IP address 1.
When the IpAccessHostGpb MO is configured as multihomed, the
IpInterfaces configured for interface1 and interface2 must not be
configured on the same ET board.
If interface1 and interface2 is configured with IpInterfaceGroup MO, then
none of the IpInterfaces configured on any of the IpInterfaceGroups may
be configured on the same board.
The interface specified in this attribute can be added or removed by the
respective actions for adding or removing interfaces.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostGpb

interface1

RNC

Network Parameters

80 (520)

Reference to an IpInterface MO, IpInterfaceGroup MO or to a FastEthernet ManagedObject


MO.
If two IP addresses are used, and thus two interfaces, this interface
is for IP address 1.
When the IpAccessHostGpb MO is configured as multihomed, the
IpInterfaces configured for interface1 and interface2 must not be
configured on the same ET board.
If interface1 and interface2 is configured with IpInterfaceGroup MO,
then none of the IpInterfaces configured on any of the IpInterfaceGroups
may be configured on the same board.
The interface specified in this attribute can be added or removed by
the respective actions for adding or removing interfaces.

IpAccessHostGpb

interface2

RBS DUW

Reference to an IpInterface MO, IpInterfaceGroup MO or to a FastEthernet ManagedObject


MO.
This attribute must refer to an MO of the same type as interface1.
This attribute must be set, if ipAddress2 or autoConfigIdentity2 is set.
When the IpAccessHostGpb MO is configured as multihomed, the
IpInterfaces configured for interface1 and interface2 must not be
configured on the same ET board.
If interface1 and interface2 is configured with IpInterfaceGroup MO, then
none of the IpInterfaces configured on any of the IpInterfaceGroups may
be configured on the same board.
The interface specified in this attribute can be added or removed by the
respective actions for adding or removing interfaces.

IpAccessHostGpb

interface2

RNC

Reference to an IpInterface MO, IpInterfaceGroup MO or to a FastEthernet ManagedObject


MO.
This attribute must refer to an MO of the same type as interface1.
This attribute must be set, if ipAddress2 or autoConfigIdentity2 is
set.
When the IpAccessHostGpb MO is configured as multihomed, the
IpInterfaces configured for interface1 and interface2 must not be
configured on the same ET board.
If interface1 and interface2 is configured with IpInterfaceGroup MO,
then none of the IpInterfaces configured on any of the IpInterfaceGroups
may be configured on the same board.
The interface specified in this attribute can be added or removed by
the respective actions for adding or removing interfaces.

IpAccessHostGpb
IpAccessHostGpb

Prepared: EZIEAGA

IpAccessHostGpbId
IpAccessHostGpbId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostGpb

ipAddress1

RBS DUW

Network Parameters

The first IP address of the host.

81 (520)

string

0.0.0.0

string

0.0.0.0

string

0.0.0.0

This IP address must be unique with respect to other hosts in the node.
This attribute must be set, only if autoConfig is set to OFF.
This IP address must belong to the subnet which is indicated in the MO
referenced by interface1 or interface2.
In case interface1 or interface2 references an IpInterfaceGroup MO the
subnet is specified in the IpInterfaces referenced from the IpInterfaceGroup
MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

IpAccessHostGpb

ipAddress1

RNC

The first IP address of the host.


This IP address must be unique with respect to other hosts in the
node.
This attribute must be set, only if autoConfig is set to OFF.
This IP address must belong to the subnet which is indicated in the
MO referenced by interface1 or interface2.
In case interface1 or interface2 references an IpInterfaceGroup MO
the subnet is specified in the IpInterfaces referenced from the
IpInterfaceGroup MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

IpAccessHostGpb

ipAddress2

RBS DUW

The second IP address of the host.


This IP address must be unique with respect to other hosts in the node.
This attribute must be set, only if autoConfig is set to OFF.
This IP address must belong to the subnet which is indicated in the MO
referenced by interface1 or interface2.
In case interface1 or interface2 references an IpInterfaceGroup MO the
subnet is specified in the IpInterfaces referenced from the IpInterfaceGroup
MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostGpb

ipAddress2

RNC

Network Parameters

The second IP address of the host.

82 (520)

string

0.0.0.0

This IP address must be unique with respect to other hosts in the


node.
This attribute must be set, only if autoConfig is set to OFF.
This IP address must belong to the subnet which is indicated in the
MO referenced by interface1 or interface2.
In case interface1 or interface2 references an IpInterfaceGroup MO
the subnet is specified in the IpInterfaces referenced from the
IpInterfaceGroup MO.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.
IpAccessHostGpb

ipDefaultTtl

RBS DUW

The default value of the Time-To-Live (TTL) field of the IP header. The
value is inserted into datagrams originating at this host, whenever a TTL
value is not supplied by the transport layer protocol.

long

1..255

64

64

IpAccessHostGpb

ipDefaultTtl

RNC

The default value of the Time-To-Live (TTL) field of the IP header. The
value is inserted into datagrams originating at this host, whenever a TTL
value is not supplied by the transport layer protocol.

long

1..255

64

64

IpAccessHostGpb

operationalState

RBS DUW

The operational state.

OperState

IpAccessHostGpb

operationalState

RNC

The operational state.

OperState

IpAccessHostGpb

reassemblyTimeout

RBS DUW

The maximum number of milliseconds, during which received fragments


are held while they are awaiting reassembly at this host.
Specification: RFC 4963

long

1..120000

60000

IpAccessHostGpb

reassemblyTimeout

RNC

The maximum number of milliseconds, during which received fragments


are held while they are awaiting reassembly at this host.
Specification: RFC 4963

long

1..120000

60000

IpAccessHostGpb
IpAccessHostGpb
IpAccessHostGpb
IpAccessHostGpb

reservedByMos
reservedByMos
userLabel
userLabel

RBS DUW
RNC
RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.
Label for free use.
Label for free use.

ManagedObject
ManagedObject
string
string

IpAccessHostPool

administrativeState

RNC

The administrative state of the IpAccessHostPool.

SupportedAdminStates

IpAccessHostPool

availabilityStatus

RNC

The availability status of the IpAccessHostPool.


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9 or bit 10 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED

long

IpAccessHostPool
IpAccessHostPool

IpAccessHostPoolId
ipAccessHostRef

RNC
RNC

Naming attribute. Contains the value part of the RDN.


List of IP Access Hosts that belong to the pool

string
IpAccessHostEt

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

LOCKED = 0
UNLOCKED = 1

LOCKED(0)

Takes effect: New connections


0..2047

Sequence length must be in the range 0..144

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

IpAccessHostPool

operationalState

RNC

The operational state of the IpAccessHostPool.

IpAccessHostPool

reservedBy

RNC

IpAccessHostPool

userLabel

RNC

IpAccessHostSpb

activeSpmId

RNC

List of references, updated automatically by the RNC, that point back


ManagedObject
toward the MO instances that have references to this MO instance.
Provides the possibility to put a user-friendly label on the MO instance. The string
value is not used by the RNC.
Reference to the active Spm MO or PiuDevice MO.
ManagedObject

SupportedOperStates

83 (520)
DISABLED = 0
ENABLED = 1

After restart, the reference is the same as the spmId.


The reference can be set only by the user of the IpAccessHostSpb
MO.
IpAccessHostSpb

administrativeState

RNC

The administrative state.

AdmState

IpAccessHostSpb

autoConfig

RNC

This attribute specifies whether autoconfiguration for the IP Access Host is AutoConfigurationMode
used.

IpAccessHostSpb

autoConfigIdentity

RNC

The identity of the IpAccessAutoConfig MO used by this host.

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

ON = 1
OFF = 2

OFF(2)

IpAccessAutoConfig

This attribute is mandatory if autoConfig is set to ON.


IpAccessHostSpb

autoConfigIdentity2

RNC

The identity of the IpAccessAutoConfig MO used by this host.

IpAccessAutoConfig

This attribute must be set, if autoConfig is set to ON and if the host


has two IP addresses assigned automatically.
IpAccessHostSpb

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.

IpAccessHostSpb

interface2

RNC

Reference to an IpInterface MO.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

IpInterface

The attributes ipInterface and interface2 have their own instances


of the IpInterface MO. When the IpAccessHostSpb MO is configured as
multihomed, do not configure these IpInterface MOs on the same ET IP
board.
The interface specified in this attribute can be added or removed by
the respective actions for adding or removing interfaces.

IpAccessHostSpb

Prepared: EZIEAGA

IpAccessHostSpbId

RNC

The value component of the RDN.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessHostSpb

ipAddress

RNC

Network Parameters

The first IP address of the host.

84 (520)

string

0.0.0.0

string

0.0.0.0

This IP address must be unique with respect to other hosts in the


node.
This attribute must be set, only if autoConfig is set to OFF.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.
IpAccessHostSpb

ipAddress2

RNC

The second IP address of the host at multihoming.


This IP address must be unique with respect to other hosts in the
node.
This attribute must be set, only if autoConfig is set to OFF.
This IP address must belong to the subnet which is indicated in the
MO referenced by ipInterface or interface2.
Lock before modify: Yes
Disturbances: Changing this attribute can affect traffic.

IpAccessHostSpb

ipDefaultTtl

RNC

The default value of the Time-To-Live (TTL) field of the IP header. The
value is inserted into datagrams originating at this host, whenever a TTL
value is not supplied by the transport layer protocol.

long

IpAccessHostSpb

ipInterface

RNC

Reference to an IpInterface MO.

IpInterface

1..255

64

64

The attributes ipInterface and interface2 have their own instances


of the IpInterface MO. When the IpAccessHostSpb MO is configured as
multihomed, do not configure these IpInterface MOs on the same ET IP
board.
The interface specified in this attribute can be added or removed by
the respective actions for adding or removing interfaces.

IpAccessHostSpb

operationalState

RNC

The operational state.

OperState

IpAccessHostSpb

reassemblyTimeout

RBS DUW

The maximum number of milliseconds, during which received fragments


are held while they are awaiting reassembly at this host.
Specification: RFC 4963

long

1..120000

DISABLED = 0
ENABLED = 1
60000

60000

IpAccessHostSpb

reassemblyTimeout

RNC

The maximum number of milliseconds, during which received fragments


are held while they are awaiting reassembly at this host.
Specification: RFC 4963

long

1..120000

60000

60000

IpAccessHostSpb

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

IpAccessHostSpb

spmId

RNC

Reference to an instance of Spm MO or PiuDevice MO.

ManagedObject

Default location of the IP host after a node restart. The location can
be overridden by the value of the attribute activeSpmId.
IpAccessHostSpb

Prepared: EZIEAGA

userLabel

RNC

Label for free use.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAccessSctp

availabilityStatus

RBS DUW

Network Parameters

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

IpAccessSctp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

IpAccessSctp

ipAccessHostEtRef1

RBS DUW

The identity of a primary IpAccessHostEt referred to by this MO.

85 (520)

ManagedObject

The attributes, ipAccessHostEtRef1 and ipAccessHostEtRef2, must not


refer to the same IpAccessHostEt MO instance.
This attribute must always contain a valid MO reference.
IpAccessSctp

ipAccessHostEtRef1

RNC

The identity of a primary IpAccessHostEt referred to by this MO.

ManagedObject

The attributes, ipAccessHostEtRef1 and ipAccessHostEtRef2, must


not refer to the same IpAccessHostEt MO instance.
This attribute must always contain a valid MO reference.

IpAccessSctp

ipAccessHostEtRef2

RBS DUW

The identity of a secondary IpAccessHostEt referred to by this MO.

ManagedObject

The attributes, ipAccessHostEtRef1 and ipAccessHostEtRef2, must not


refer to the same IpAccessHostEt MO instance.
IpAccessSctp

ipAccessHostEtRef2

RNC

The identity of a secondary IpAccessHostEt referred to by this MO.

ManagedObject

The attributes, ipAccessHostEtRef1 and ipAccessHostEtRef2, must


not refer to the same IpAccessHostEt MO instance.

IpAccessSctp
IpAccessSctp

IpAccessSctpId
IpAccessSctpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

IpAccessSctp

operationalState

RBS DUW

The operational state.

OperState

IpAccessSctp

operationalState

RNC

The operational state.

OperState

IpAccessSctp
IpAccessSctp

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserves this MO instance.


Contains a list of MO instances that reserves this MO instance.

ManagedObject
ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

IpAccessSctp
IpAccessSctp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

IpAtmLink

aal5TpVccTpId

RBS DUW

Reference to an Aal5TpVccTp MO instance that represents the underlying ManagedObject


AAL5 termination point (of an AAL5 PVC:s) for the IP over ATM link.

86 (520)

string
string

The operator gives the name of the Aal5TpVccTp MO to be used by the IP


over ATM link.
Only Aal5TpVccTp MOs that terminates on an MP (Main Processor) may
be used when setting up IpAtmLink MOs.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity.If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

IpAtmLink

aal5TpVccTpId

RNC

Reference to an Aal5TpVccTp MO instance that represents the underlying ManagedObject


AAL5 termination point (of an AAL5 PVC:s) for the IP over ATM link.
The operator gives the name of the Aal5TpVccTp MO to be used by
the IP over ATM link.
Only Aal5TpVccTp MOs that terminates on an MP (Main Processor)
may be used when setting up IpAtmLink MOs.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity.If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

IpAtmLink

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAtmLink

availabilityStatus

RNC

Network Parameters

The availability status.

87 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

IpAtmLink
IpAtmLink

interfaceName
interfaceName

RBS DUW
RNC

The interface name.


The interface name.

string
string

IpAtmLink

ipAddress

RBS DUW

The input format used by the operator is four fields of digits, separated by a string
dot. Each field consists of three digits.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity. If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

IpAtmLink

ipAddress

RNC

The input format used by the operator is four fields of digits, separated by a string
dot. Each field consists of three digits.
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity. If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

IpAtmLink
IpAtmLink

IpAtmLinkId
IpAtmLinkId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

IpAtmLink

metric

RBS DUW

The attribute metric states the metric "cost" of the IP over ATM link. The
metric value is calculated as 10^8 /link bit speed.

long

1..32767

For example:
Metric for 10 Mbps Ethernet = 10^8/10^7 = 10
Metric for 100 Mbps Ethernet = 10^8/10^8 = 1
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity. If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAtmLink

metric

RNC

Network Parameters

The attribute metric states the metric "cost" of the IP over ATM link. The
metric value is calculated as 10^8 /link bit speed.

long

88 (520)
1..32767

For example:
Metric for 10 Mbps Ethernet = 10^8/10^7 = 10
Metric for 100 Mbps Ethernet = 10^8/10^8 = 1
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity. If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

IpAtmLink

monitor

RBS DUW

Specifies whether InvATMARP monitor is turned on or off.

boolean

0 TRUE(1)

boolean

TRUE(1)

Disturbances: Changing this attribute on this MO may cause a disturbance


or loss of OAM connectivity because of degraded supervision of the link. If
there are any doubts regarding the results of the attribute changes, it is
strongly recommended to activate the robust rollback function, by setting
the attribute configCountdownActivated on the ConfigurationVersion MO
first.
IpAtmLink

monitor

RNC

Specifies whether InvATMARP monitor is turned on or off.


Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity because of degraded supervision
of the link. If there are any doubts regarding the results of the attribute
changes, it is strongly recommended to activate the robust rollback
function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

IpAtmLink

monitorInterval

RBS DUW

The interval between sending monitor packets.

long

1..60

10

10

long

1..60

10

60

long
long

1..255
1..255

10
10

10
10

1500

1500

Unit: 1 s
IpAtmLink

monitorInterval

RNC

The interval between sending monitor packets.


Unit: 1 s

IpAtmLink
IpAtmLink

monitorRetries
monitorRetries

RBS DUW
RNC

The number of retries when sending monitor packets.


The number of retries when sending monitor packets.

IpAtmLink

mtuSize

RBS DUW

Specifies the maximum IP datagram size that may be sent on the IP over long
ATM link in bytes, without fragmentation. Recommended MTU size is 1500
bytes to prevent IP fragmentation.

576..2040

Note that the size of the IP datagram does not include the 8 Bytes added
for the LLC/SNAP header before putting the IP datagram in AAL5 SDU.
Unit: 1 B
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity. If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAtmLink

mtuSize

RNC

Network Parameters

Specifies the maximum IP datagram size that may be sent on the IP over long
ATM link in bytes, without fragmentation. Recommended MTU size is 1500
bytes to prevent IP fragmentation.

89 (520)
576..2040

1500

1500

Note that the size of the IP datagram does not include the 8 Bytes
added for the LLC/SNAP header before putting the IP datagram in AAL5
SDU.
Unit: 1 B
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity. If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

IpAtmLink

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

This attribute is dependent of the supervision of the link or, if it is closed, of


the operational states of the underlying AAL5 termination points
(Aal5TpVccTp MO) that are used to transport IP datagrams.
IpAtmLink

operationalState

RNC

The operational state.


This attribute is dependent of the supervision of the link or, if it is
closed, of the operational states of the underlying AAL5 termination points
(Aal5TpVccTp MO) that are used to transport IP datagrams.

IpAtmLink

reservedBy

RBS DUW

Contains an OspfInterface MO instance that reserves this MO instance.

OspfInterface

IpAtmLink

reservedBy

RNC

Contains an OspfInterface MO instance that reserves this MO instance.

OspfInterface

IpAtmLink

subnetMask

RBS DUW

The attribute subnetMask states the subnet mask of the IP over ATM link
(point-to-point link).

string

The input format used by the operator is four fields of digits, separated by a
dot. Each field consists of three digits.
For a point-to-point link, the subnet mask 255.255.255.252 is very likely.
The subnet mask has to be contiguous. That is, it has the LSB's set to 0
(zero).
Example:
255.255.255.X
Contiguous subnet masks:
11111111.11111111.11111111.11111100 (X = 252)
11111111.11111111.11111111.11111000 (X = 248)
Non-contiguous subnet mask:
11111111.11111111.11111111.11110100 (X = 244)
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity. If there are any doubts regarding the results of
the attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpAtmLink

subnetMask

RNC

Network Parameters

The attribute subnetMask states the subnet mask of the IP over ATM link
(point-to-point link).

90 (520)

string

The input format used by the operator is four fields of digits,


separated by a dot. Each field consists of three digits.
For a point-to-point link, the subnet mask 255.255.255.252 is very
likely.
The subnet mask has to be contiguous. That is, it has the LSB's set
to 0 (zero).
Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)
Disturbances: Changing this attribute on this MO may cause a
disturbance or loss of OAM connectivity. If there are any doubts regarding
the results of the attribute changes, it is strongly recommended to activate
the robust rollback function, by setting the attribute
configCountdownActivated on the ConfigurationVersion MO first.

IpAtmLink
IpAtmLink

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

IpEthPacketDataRouter

administrativeState

RNC

The administrative state of the IpEthPacketDataRouter

SupportedAdminStates

IpEthPacketDataRouter

availabilityStatus

RNC

The availability status of the IpEthPacketDataRouter


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9, 10, or 11 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED
Bit 11 = 1: DEPENDENCYSHUTTINGDOWN

long

IpEthPacketDataRouter
IpEthPacketDataRouter

ipAccessHostSpbRef
ipAddressSelection

RNC
RNC

Reference to IpAccessHostSpb MO.


Specifies which IP address to use from the IpAccessHostSpb MO
referenced in ipAccessHostSpbRef.
IP_ADDRESS_1 is mapped to IpAccessHostSpb::ipAddress.
IP_ADDRESS_2 is mapped to IpAccessHostSpb::ipAddress2.

IpAccessHostSpb
SupportedIpAddresses

LOCKED = 0
UNLOCKED = 1

LOCKED(0)

IP_ADDRESS_1 = 0
IP_ADDRESS_2 = 1

IP_ADDRESS_1(0
)

0..4095

Dependencies: Instances of this MO that refer to the same


IpAccessHostSpb (attribute ipAccessHostSpbRef) must have different
values for this parameter.
IpEthPacketDataRouter
IpEthPacketDataRouter

Prepared: EZIEAGA

IpEthPacketDataRouterId
operationalState

RNC
RNC

Naming attribute. Contains the value part of the RDN.


The operational state of the IpEthPacketDataRouter

Date: 2014-05-27
Sheet: 14.0.2

string
SupportedOperStates

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpEthPacketDataRouter

reservedBy

RNC

IpEthPacketDataRouter

userLabel

RNC

IpHostLink

availabilityStatus

RBS DUW

Network Parameters

List of references, updated automatically by the RNC, that point back


toward the MO instances that have references to this MO instance.

91 (520)

IuLink

Sequence length must be in the range 0..16


Provides the possibility to put a user-friendly label on the MO instance. The string
value is not used by the RNC.
The availability status.
AvailabilityStatus
It contains details about operationalState.

IpHostLink

interfaceName

RBS DUW

The interface name.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string

Dependencies: The value of this attribute can be used as a reference, by


the attributes nodeInterfaceName or nodeIpv6InterfaceName in the Ip MO.
IpHostLink
IpHostLink

IpHostLinkId
ipInterfaceMoRef

RBS DUW
RBS DUW

The value component of the RDN.


Reference to an instance of IpInterface MO, Ipv6Interface MO or
VpnInterface MO.

string
ManagedObject

Only one IpHostLink is allowed to refer to the same IpInterface MO,


Ipv6Interface MO or VpnInterface MO.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity,if the network management tool is connected
via the IpHostLink MO. If there are any doubts regarding the results of the
attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.

IpHostLink

ipv4Addresses

RBS DUW

Specifies a list of all IPv4 addresses for the IpHostLink MO.


string
The first entry of this list can be used as OAM IP address for the node. See
the Ip MO for configuration of OAM IP address for the node.
The first entry of this list is also represented by the IPv4 address attribute:
ipAddress.
The IP addresses must belong to the subnet defined in the referenced
IpInterface MO or VpnInterface MO.
Dependencies: This attribute can only be set if this MO refers to IpInterface
MO or VpnInterface MO.
The first element of this attribute cannot be set to 0.0.0.0 or an empty
string, if this specific IpHostLink is referenced by the attribute
nodeInterfaceName in Ip MO.
Disturbances: Changing this attribute on this MO may cause a disturbance
or loss of OAM connectivity or ORB restart,if the network management tool
is connected via the IpHostLink MO. If there are any doubts regarding the
results of the attribute changes, it is strongly recommended to activate the
robust rollback function, by setting the attribute configCountdownActivated
on the ConfigurationVersion MO first.

IpHostLink

Prepared: EZIEAGA

operationalState

RBS DUW

The operational state.

OperState

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpHostLink
IpInterface

userLabel
availabilityStatus

RBS DUW
RBS DUW

Network Parameters

Label for free use.


The availability status.

string
AvailabilityStatus

It contains details about operationalState.

IpInterface

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.

IpInterface

defaultRouter0

RBS DUW

The IP address of the default router 0.

92 (520)

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string

It is not allowed to set the value of this attribute to 0.0.0.0. The attributes
defaultRouter0, defaultRouter1 and defaultRouter2 must not indicate the
same IP address.
If rps is set to false, the egress traffic is always directed to this default
router.
If the address of the defaultRouter0 is changed, it has to belong to the
subnet defined by the networkPrefixLength and attribute rps must be set to
false.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO. If the subnet address is to be
changed by changing the network part of defaultRouter0, any other IP host
that is configured on this IpInterface MO must first be removed. This means
that the reservedBy attribute can contain only a single reference to an
IpHostLink MO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

defaultRouter0

RNC

Network Parameters

The IP address of the default router 0.

93 (520)

string

It is not allowed to set the value of this attribute to 0.0.0.0. The


attributes defaultRouter0, defaultRouter1 and defaultRouter2 must not
indicate the same IP address.
If rps is set to false, the egress traffic is always directed to this
default router.
If the address of the defaultRouter0 is changed, it has to belong to
the subnet defined by the networkPrefixLength and attribute rps must be
set to false.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO. If the subnet address is to be
changed by changing the network part of defaultRouter0, any other IP host
that is configured on this IpInterface MO must first be removed. This means
that the reservedBy attribute can contain only a single reference to an
IpHostLink MO.

IpInterface

defaultRouter0State

RBS DUW

Indicates whether ping supervision is successful toward default router 0.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

If router path supervision is turned off (rps = false) the value of this attribute
is ENABLED.
IpInterface

defaultRouter0State

RNC

Indicates whether ping supervision is successful toward default router 0.


If router path supervision is turned off (rps = false) the value of this
attribute is ENABLED.

IpInterface

defaultRouter1

RBS DUW

The IP address of the default router 1.

string

0.0.0.0

string

0.0.0.0

The attributes defaultRouter0, defaultRouter1 and defaultRouter2 must not


indicate the same IP address.
If the address of the defaultRouter1 is changed, it has to belong to the
subnet defined by the networkPrefixLength or set to value 0.0.0.0. The
attribute rps must have value false when the change is performed.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.
IpInterface

defaultRouter1

RNC

The IP address of the default router 1.


The attributes defaultRouter0, defaultRouter1 and defaultRouter2
must not indicate the same IP address.
If the address of the defaultRouter1 is changed, it has to belong to
the subnet defined by the networkPrefixLength or set to value 0.0.0.0. The
attribute rps must have value false when the change is performed.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.

IpInterface

defaultRouter1State

RBS DUW

Indicates whether ping supervision is successful toward default router 1.

OperState

DISABLED = 0
ENABLED = 1

If no default router 1 is configured, the value of this attribute is DISABLED.


If router path supervision is turned off (rps = false) the value of this attribute
is ENABLED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

defaultRouter1State

RNC

Network Parameters

Indicates whether ping supervision is successful toward default router 1.

94 (520)

OperState

DISABLED = 0
ENABLED = 1

If no default router 1 is configured, the value of this attribute is


DISABLED.
If router path supervision is turned off (rps = false) the value of this
attribute is ENABLED.

IpInterface

defaultRouter2

RBS DUW

The IP address of the default router 2.

string

0.0.0.0

string

0.0.0.0

The attributes defaultRouter0, defaultRouter1 and defaultRouter2 must not


indicate the same IP address.
If the address of the defaultRouter2 is changed, it has to belong to the
subnet defined by the networkPrefixLength or set to value 0.0.0.0. The
attribute rps must have value false when the change is performed.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.
IpInterface

defaultRouter2

RNC

The IP address of the default router 2.


The attributes defaultRouter0, defaultRouter1 and defaultRouter2
must not indicate the same IP address.
If the address of the defaultRouter2 is changed, it has to belong to
the subnet defined by the networkPrefixLength or set to value 0.0.0.0. The
attribute rps must have value false when the change is performed.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.

IpInterface

defaultRouter2State

RBS DUW

Indicates whether ping supervision is successful toward default router 2.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

If no default router 2 is configured, the value of this attribute is DISABLED.


If router path supervision is turned off (rps = false) the value of this attribute
is ENABLED.

IpInterface

defaultRouter2State

RNC

Indicates whether ping supervision is successful toward default router 2.


If no default router 2 is configured, the value of this attribute is
DISABLED.
If router path supervision is turned off (rps = false) the value of this
attribute is ENABLED.

IpInterface

defaultRouterPingInterval

RBS DUW

The interval at which the default router is ping-ed.

long

3..100

Must be larger than or equal to maxWaitForPingReply.


The value of this attribute is irrelevant, if rps = false.
Unit: 100 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

defaultRouterPingInterval

RNC

The interval at which the default router is ping-ed.

Network Parameters
long

95 (520)
3..100

Must be larger than or equal to maxWaitForPingReply.


The value of this attribute is irrelevant, if rps = false.
Unit: 100 ms
IpInterface

defaultRouterTraffic

RBS DUW

Indicates which of the default routers is selected for egress traffic.

DefaultTraffic

TRAFFIC_DEF_ROUTER_0 = 0
TRAFFIC_DEF_ROUTER_1 = 1
TRAFFIC_DEF_ROUTER_2 = 2

TRAFFIC_DEF_R
OUTER_0(0)

IpInterface

defaultRouterTraffic

RNC

Indicates which of the default routers is selected for egress traffic.

DefaultTraffic

TRAFFIC_DEF_ROUTER_0 = 0
TRAFFIC_DEF_ROUTER_1 = 1
TRAFFIC_DEF_ROUTER_2 = 2

TRAFFIC_DEF_R
OUTER_0(0)

IpInterface
IpInterface

IpInterfaceId
IpInterfaceId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

IpInterface

maxNoOfFailedPings

RBS DUW

Maximum number of consecutive failed pings before the contact with the
default router is considered to be lost.

long

1..10

IpInterface

maxNoOfFailedPings

RNC

long

1..10

3..100

3..100

This value is irrelevant, if rps = false.


Maximum number of consecutive failed pings before the contact with the
default router is considered to be lost.
This value is irrelevant, if rps = false.
IpInterface

maxWaitForPingReply

RBS DUW

If echo reply is not received within this time, ping supervision is considered long
to be failed.
This value is irrelevant, if rps = false.
Unit: 100 ms

IpInterface

maxWaitForPingReply

RNC

If echo reply is not received within this time, ping supervision is considered long
to be failed.
This value is irrelevant, if rps = false.
Unit: 100 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

mtu

RBS DUW

Network Parameters

The maximum transfer unit, that is the maximum number of Ethernet


payload octets sent in an Ethernet frame.

96 (520)

long

576..2018

1500

1500

long

576..2018

1500

1500

The actual MTU used by the hardware might be lower than the configured
value due to HW limitations. See the description of the relevant board for
details.
If the attribute frameFormat = IEEE_802_3_LLC_SNAP, the maximum
value of mtu is 1492.
The maximum value of mtu is 2000, if at least one of the following
conditions are fulfilled:
- the parent MO is GigaBitEthernet and linkType = BACKPLANE_PORTS
- the board supports jumbo frames. See the description of the relevant
board.
In other cases, the maximum value of mtu is 1500.
As a general rule, IpInterface MOs belonging to the same
InternalEthernetPort MO or the same GigaBitEthernet MO must have the
same MTU value, that is the same value on this attribute. However, some
boards allow for a more flexible setting of MTU. See the description of the
relevant board.
Unit: 1 B
Dependencies: The maximum value for mtu depends on the attributes
frameFormat and linkType in the parent MO GigaBitEthernet or
frameFormat in the parent MO InternalEthernetPort. It also depends on if
jumbo frames are supported.

IpInterface

mtu

RNC

The maximum transfer unit, that is the maximum number of Ethernet


payload octets sent in an Ethernet frame.
The actual MTU used by the hardware might be lower than the
configured value due to HW limitations. See the description of the relevant
board for details.
If the attribute frameFormat = IEEE_802_3_LLC_SNAP, the
maximum value of mtu is 1492.
The maximum value of mtu is 2000, if at least one of the following
conditions are fulfilled:
- the parent MO is GigaBitEthernet and linkType =
BACKPLANE_PORTS
- the board supports jumbo frames. See the description of the
relevant board.
In other cases, the maximum value of mtu is 1500.
As a general rule, IpInterface MOs belonging to the same
InternalEthernetPort MO or the same GigaBitEthernet MO must have the
same MTU value, that is the same value on this attribute. However, some
boards allow for a more flexible setting of MTU. See the description of the
relevant board.
Unit: 1 B
Dependencies: The maximum value for mtu depends on the
attributes frameFormat and linkType in the parent MO GigaBitEthernet or
frameFormat in the parent MO InternalEthernetPort. It also depends on if
jumbo frames are supported.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

networkPrefixLength

RBS DUW

Network Parameters

The subnet mask.

97 (520)

long

8..30

long

8..30

Minimum number of consecutive successful pings before a default router is long


considered to be reachable, after having been considered unreachable.

1..10

1..10

Example: networkPrefixLength = 24, subnet mask is 255.255.255.0


Example: networkPrefixLength = 28, subnet mask is 255.255.255.240
Unit: 1 bits
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO. If the subnet address is to be
changed by changing networkPrefixLength, any other IP host that is
configured on this IpInterface MO must first be removed. This means that
the reservedBy attribute can contain only a single reference to an
IpHostLink MO.
IpInterface

networkPrefixLength

RNC

The subnet mask.


Example: networkPrefixLength = 24, subnet mask is 255.255.255.0
Example: networkPrefixLength = 28, subnet mask is
255.255.255.240
Unit: 1 bits
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO. If the subnet address is to be
changed by changing networkPrefixLength, any other IP host that is
configured on this IpInterface MO must first be removed. This means that
the reservedBy attribute can contain only a single reference to an
IpHostLink MO.

IpInterface

noOfPingsBeforeOk

RBS DUW

This value is irrelevant, if rps = false.


IpInterface

noOfPingsBeforeOk

RNC

Minimum number of consecutive successful pings before a default router is long


considered to be reachable, after having been considered unreachable.
This value is irrelevant, if rps = false.

IpInterface

operationalState

RBS DUW

The operational state.

OperState

IpInterface

operationalState

RNC

The operational state.

OperState

IpInterface

ownIpAddressActive

RBS DUW

The IP address of Router Path Supervision on the active link.

string

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0.0.0.0

The active link is the one where traffic is handled.


This IP address must be set, if rps = true.
This IP address can be shared with a host that is connected to the IP
interface, but apart from that, the IP address must be unique.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

ownIpAddressActive

RNC

Network Parameters

The IP address of Router Path Supervision on the active link.

98 (520)

string

0.0.0.0

string

0.0.0.0

string

0.0.0.0

The active link is the one where traffic is handled.


This IP address must be set, if rps = true.
This IP address can be shared with a host that is connected to the
IP interface, but apart from that, the IP address must be unique.
Dependencies: This attribute can be changed using the action
assignIpAddress on the IpHostLink MO.
IpInterface

ownIpAddressPassive

RBS DUW

The IP address of Router Path Supervision on the passive link.


This IP address must be unique in the node if the attribute rps is set to true.
The attribute is not valid if the IpInterface belongs to an
InternalEthernetPort MO.

IpInterface

ownIpAddressPassive

RNC

The IP address of Router Path Supervision on the passive link.


This IP address must be unique in the node if the attribute rps is set
to true.
The attribute is not valid if the IpInterface belongs to an
InternalEthernetPort MO.

IpInterface

reservedBy

RBS DUW

Contains a list of MO instances that reserve this MO instance.

ManagedObject

A maximum of 96 users can reserve the IpInterface MOs configured on the


same logical network.
IpInterface

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

A maximum of 96 users can reserve the IpInterface MOs configured


on the same logical network.
IpInterface

rps

RBS DUW

Router Path Supervision

boolean

Router Path Supervision is done on the links defined by


ownIpAddressActive and ownIpAddressPassive, if they have valid IP
addresses defined when they are created.
It is possible to enable Router Path Supervision after the creation of the
IpInterface MO, if it is disabled when the MO is created (rps = false) and if
ownIpAddressActive is set.
It is possible to disable Router Path Supervision when the IpInterface MO
has been created, by setting this attribute to false.
If this attribute is set to false, the egress traffic is directed to
defaultRouter0, which means that traffic disturbances will occur if the
default router 0 is unavailable.
If a router redundancy protocol, e.g. Virtual Router Redundancy Protocol
(VRRP) is used, it is recommended that this attribute is set to false, in order
to avoid interference.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

rps

RNC

Network Parameters

Router Path Supervision

99 (520)

boolean

Router Path Supervision is done on the links defined by


ownIpAddressActive and ownIpAddressPassive, if they have valid IP
addresses defined when they are created.
It is possible to enable Router Path Supervision after the creation of
the IpInterface MO, if it is disabled when the MO is created (rps = false)
and if ownIpAddressActive is set.
It is possible to disable Router Path Supervision when the
IpInterface MO has been created, by setting this attribute to false.
If this attribute is set to false, the egress traffic is directed to
defaultRouter0, which means that traffic disturbances will occur if the
default router 0 is unavailable.
If a router redundancy protocol, e.g. Virtual Router Redundancy
Protocol (VRRP) is used, it is recommended that this attribute is set to
false, in order to avoid interference.

IpInterface

subnet

RBS DUW

This attribute contains the subnet address of the IpInterface MO.

string

0.0.0.0

string

0.0.0.0

The subnet address is constructed from the address in defaultRouter0 and


the attribute networkPrefixLength.
IpInterface

subnet

RNC

This attribute contains the subnet address of the IpInterface MO.


The subnet address is constructed from the address in
defaultRouter0 and the attribute networkPrefixLength.

IpInterface

switchBackTimer

RBS DUW

Switchback timer

long

1..3600

180

180

long

1..3600

180

180

When a higher-priority router has become reachable, the traffic switches


back to default router 0 or default router 1, after expiry of the switchback
timer.
This value is irrelevant, if rps = false.
Unit: 1 s
IpInterface

switchBackTimer

RNC

Switchback timer
When a higher-priority router has become reachable, the traffic
switches back to default router 0 or default router 1, after expiry of the
switchback timer.
This value is irrelevant, if rps = false.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

trafficType

RBS DUW

Network Parameters

The type of traffic on this interface.

100 (520)

IpTrafficType

NOT_USED = 0
SIGNALING = 1
PAYLOAD = 2
SIGNALING_AND_PAYLOAD = 3
SYNCHRONIZATION = 4

This attribute is only for information, setting it does not affect traffic or
system behaviour.

NOT_USED(0)

SIGNALING_AND_SYNCHRONIZATI
ON = 5
PAYLOAD_AND_SYNCHRONIZATIO
N=6
SIGNALING_AND_PAYLOAD_AND_
SYNCHRONIZATION = 7
OPERATION_AND_MAINTENENCE
=8

IpInterface

trafficType

RNC

The type of traffic on this interface.

IpTrafficType

NOT_USED = 0
SIGNALING = 1
PAYLOAD = 2
SIGNALING_AND_PAYLOAD = 3
SYNCHRONIZATION = 4

This attribute is only for information, setting it does not affect traffic
or system behaviour.

NOT_USED(0)

SIGNALING_AND_SYNCHRONIZATI
ON = 5
PAYLOAD_AND_SYNCHRONIZATIO
N=6
SIGNALING_AND_PAYLOAD_AND_
SYNCHRONIZATION = 7
OPERATION_AND_MAINTENENCE
=8

IpInterface
IpInterface

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

IpInterface

vid

RBS DUW

The Virtual LAN (VLAN) identifier.

long

0..4094

long

0..4094

This attribute is applicable only when:


- vLan is set to true
- vlanRef is set to NULL.
vid 0 = priority tag only
vid 1 - 4094 = with priority tag and vlan id
If vlanRef is set to a non-NULL value, it resets the value of this attribute to
1.
Disturbances: Changing this attribute may cause traffic disturbances.
IpInterface

vid

RNC

The Virtual LAN (VLAN) identifier.


This attribute is applicable only when:
- vLan is set to true
- vlanRef is set to NULL.
vid 0 = priority tag only
vid 1 - 4094 = with priority tag and vlan id
If vlanRef is set to a non-NULL value, it resets the value of this
attribute to 1.
Disturbances: Changing this attribute may cause traffic
disturbances.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpInterface

vLan

RBS DUW

Network Parameters

Specifies whether VLAN tagging is used on this interface.

101 (520)

boolean

This attribute is applicable only when:


- vlanRef is set to NULL.
Ethernet frames are untagged only when this attribute is set to false and
vlanRef is set to NULL.
If vlanRef is set to a non-NULL value, it resets the value of this attribute to
false.
Disturbances: Changing this attribute can affect traffic.
IpInterface

vLan

RNC

Specifies whether VLAN tagging is used on this interface.

boolean

This attribute is applicable only when:


- vlanRef is set to NULL.
Ethernet frames are untagged only when this attribute is set to false
and vlanRef is set to NULL.
If vlanRef is set to a non-NULL value, it resets the value of this
attribute to false.
Disturbances: Changing this attribute can affect traffic.
IpInterface

vlanRef

RNC

Reference to an instance of a Vlan MO.

ManagedObject

The referenced instance represents an external VLAN that is


opened on this port.
This attribute is applicable only when this instance is related to a
GigaBitEthernet MO.
When configuring backplane ports, that is if the attribute linkType in
the GigaBitEthernet MO is set to BACKPLANE_PORTS, this attribute is
mandatory.
When configuring front ports, that is if the attribute linkType in the
GigaBitEthernet MO is set to FRONT_PORTS, this attribute can be used.
If this attribute is set to a non-NULL value, it overrides the values of
the attribute pair vid and vLan, which are cleared and reset to 1 and false
respectively and ignored by the system.

IpInterfaceGroup

activeIpInterfaceRef

RNC

The IP interface which is currently active and, if enabled, used for traffic.

IpInterface

IpInterfaceGroup
IpInterfaceGroup
IpInterfaceGroup
IpInterfaceGroup
IpInterfaceGroup
IpOam

IpInterfaceGroupId
primaryIpInterfaceRef
reservedBy
secondaryIpInterfaceRef
userLabel
IpOamId

RNC
RNC
RNC
RNC
RNC
RBS DUW

The value component of the RDN.


The primary IP interface.
Contains a list of MO instances that reserve this MO instance.
The secondary IP interface.
Label for free use.
The value component of the RDN.

string
IpInterface
ManagedObject
IpInterface
string
string

IpOam

IpOamId

RNC

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


IpOam
IpOam

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Ippm

featureStateTwampResponder

RBS DUW

Feature state for the TWAMP responder license controlled feature.

ActivationVals

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

ACTIVATED = 1
DEACTIVATED = 0

DEACTIVATED

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Ippm

featureStateTwampResponder

RNC

Feature state for the TWAMP responder license controlled feature.

ActivationVals

Ippm
Ippm

IppmId
licenseStateTwampResponder

RBS DUW
RBS DUW

The value component of the RDN.


License state for the TWAMP responder feature.

string
StateVals

Ippm

licenseStateTwampResponder

RNC

License state for the TWAMP responder feature.

StateVals

Ippm
IpRoutingTable

userLabel
indexOfDeletableStaticRoutes

RBS DUW
RBS DUW

Label for free use.


This attribute gives the indices for the static routes that can be deleted.

string
long

102 (520)
ACTIVATED = 1
DEACTIVATED = 0

DEACTIVATED(0)

ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0

The indices are the same as those that are listed with the action listRoutes.

IpRoutingTable

indexOfDeletableStaticRoutes

RNC

This attribute gives the indices for the static routes that can be deleted.

long

The indices are the same as those that are listed with the action
listRoutes.

IpRoutingTable

IpRoutingTableId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.


IpRoutingTable

IpRoutingTableId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


IpRoutingTable

staticRoutes

RBS DUW

List of static routes.

StaticRoute

When this attribute is set, all the static routes in the node configuration are
either added, removed, modified or unchanged.
The actions, addStaticRoute and deleteStaticRoute, can be used to add or
remove one single static route.
Disturbances: Changing this attribute can affect OAM traffic or loss of IP
connectivity. If there are any doubts regarding the results of the attribute
changes, it is strongly recommended to activate the robust rollback
function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.
IpRoutingTable

staticRoutes

RNC

List of static routes.

StaticRoute

When this attribute is set, all the static routes in the node
configuration are either added, removed, modified or unchanged.
The actions, addStaticRoute and deleteStaticRoute, can be used to
add or remove one single static route.
Disturbances: Changing this attribute can affect OAM traffic or loss
of IP connectivity. If there are any doubts regarding the results of the
attribute changes, it is strongly recommended to activate the robust
rollback function, by setting the attribute configCountdownActivated on the
ConfigurationVersion MO first.
IpRoutingTable

staticRoutes.indexOfStaticRoute

RBS DUW

IpRoutingTable

staticRoutes.indexOfStaticRoute

RNC

IpRoutingTable
IpRoutingTable

staticRoutes.ipAddress
staticRoutes.ipAddress

IpRoutingTable

staticRoutes.networkMask

Prepared: EZIEAGA

The index of the static route. It can differ from the index of the route in the
routing table.
The index of the static route. It can differ from the index of the route in the
routing table.

long

RBS DUW
RNC

The destination IP address.


The destination IP address.

string
string

RBS DUW

The destination IP network mask or network prefix length.

string

Date: 2014-05-27
Sheet: 14.0.2

long

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

IpRoutingTable

staticRoutes.networkMask

RNC

The destination IP network mask or network prefix length.

string

IpRoutingTable

staticRoutes.nextHopIpAddr

RBS DUW

The next hop IP address.

string

103 (520)

IPv6 Link Local Addresses are not supported. This refers to addresses in
the address block fe80::/10.
Specification: RFC 4291
IpRoutingTable

staticRoutes.nextHopIpAddr

RNC

The next hop IP address.

string

IPv6 Link Local Addresses are not supported. This refers to


addresses in the address block fe80::/10.
Specification: RFC 4291
IpRoutingTable

staticRoutes.redistribute

RBS DUW

IpRoutingTable

staticRoutes.redistribute

RNC

Indicates if the route should be redistributed.

boolean

This struct member is not applicable for IPv6.


Indicates if the route should be redistributed.

boolean

This struct member is not applicable for IPv6.


IpRoutingTable
IpRoutingTable

staticRoutes.routeMetric
staticRoutes.routeMetric

RBS DUW
RNC

The route metric.


The route metric.

long
long

IpRoutingTable
IpRoutingTable

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

IpSyncRef

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

IpSyncRef

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

IpSyncRef

cachedIpAddress

RBS DUW

This attribute contains the latest IP address received from the DNS server string
with the specified domain name. If domain name is not valid or no value yet
received from the DNS server this will be a null string.

IpSyncRef

IpSyncRefId

RBS DUW

The value component of the RDN.

Prepared: EZIEAGA

LOCKED(0)

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IpSyncRef

ntpServerIpAddress

RBS DUW

Network Parameters

104 (520)

This attribute contains the domain name or the IP address of the NTP
string
server to be used. It must be a valid IPv4 address or a valid domain name.
The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
A valid domain name:
- has characters of type letters, numbers and a hyphen "-", where hyphens
can be anywhere in the middle of a name, but cannot be located at the end
or beginning of a name
- cannot have spaces
- is case insensitive
- can include dots for the use of sub domains.
Two IpSyncRef MOs belonging to the same IpAccessHostEt MO, must
have different ntpServerIpAddress values.
Lock before modify: Yes

IpSyncRef

operationalState

RBS DUW

The operational state.

OperState

IpSyncRef
IpSyncRef
IpSystem

reservedBy
userLabel
IpSystemId

RBS DUW
RBS DUW
RBS DUW

Contains a list of MO instances that reserve this MO instance.


Label for free use.
The value component of the RDN.

ManagedObject
string
string

IpSystem

IpSystemId

RNC

DISABLED = 0
ENABLED = 1

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


IpSystem
IpSystem

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

IpTermServ
Ipv6Interface
Iub

reservedBy
trafficSchedulerRef
controlPlaneTransportOption

RNC
RBS DUW
RBS DUW

Contains a list of MO instances that reserve this MO instance.


ManagedObject
Reference to an instance of a TrafficScheduler MO.
ManagedObject
Transport option for the NBAP signalling bearers on the Iub interface. One TransportOptionStruct
and only one of the flags must be set to true (that is, setting of both to true,
or both to false, is not allowed). Both flags (that is, both struct members)
must be supplied at create of the MO, and at setting of the attribute.

Iub

controlPlaneTransportOption.atm

RBS DUW

ATM used as transport bearer.

boolean

Iub

controlPlaneTransportOption.ipV4

RBS DUW

IP version 4 used as transport bearer.

boolean

Iub
Iub

IubId
rbsId

RBS DUW
RBS DUW

The value component of the RDN.


Used by OSS-RC to identify an RBS and the corresponding Iub in RNC.
The attribute is not used by RBS itself, it only serves as storage for OSSRC.

string
long

Iub

userPlaneIpResourceRef

RBS DUW

Local user plane IP resource available for the Iub.

IpAccessHostEt

0..2147483647

Dependencies: Required if userPlaneTransportOption is set to IPv4.


Takes effect: At next establishment of a transport bearer.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Iub

userPlaneTransportOption

RBS DUW

Network Parameters

105 (520)

Transport option for the user plane on the Iub interface. One or both of the TransportOptionStruct
flags must be set to true. Setting of both to false is not allowed. Both flags
(that is, both struct members) must be supplied at create of the MO, and at
setting of the attribute. Setting of both to true corresponds to the Dual
Stack Iub feature.
Dependencies: If ipV4 is set to true, the userPlaneIpResourceRef is
mandatory. When both are set to true, the Dual Stack Iub feature should be
activated (see attribute featureStateDualStackIub on MO NodeBFunction).
Takes effect: For new connections.

Iub

userPlaneTransportOption.atm

RBS DUW

ATM used as transport bearer.

boolean

Iub

userPlaneTransportOption.ipV4

RBS DUW

IP version 4 used as transport bearer.

boolean

IuBcLink

cbcIpAddress

RNC

IP address of the CBC.


string
The input format used by the operator is four fields of digits, separated by
dots. Each field may consist of three digits. The value of each field shall be
in the range 0..255.
Takes effect: New connections

IuBcLink

sourceIpAddressValidation

RNC

IubLink

atmUserPlaneTermSubrackRef

RNC

Indicates if the source IP address shall be validated when the CBC


establishes a connection.
When set to TRUE, only a source IP address equal to cbcIpAddress is
accepted.

BooleanVals

FALSE = 0
TRUE = 1

TRUE(1)

TRUE(1)

Takes effect: New connections


Reference to the subrack where the ATM user plane termination of the Iub Subrack
link is located, and from which the Iub link should preferably be controlled.
The Iub link control location should be selected to minimize inter-subrack
communication during traffic handling and thus reduce overhead.
Note that the Iub link control may be located in another subrack than the
one configured in this attribute, if that subrack is full. The actual subrack
allocation of the Iub link control can be determined by looking at the
rncModuleRef attribute and then checking in which subrack that
RncModule is located.
The value of this attribute is only used in ATM transport and in RNC product
versions with an ATM switch core. However, setting this attribute to any
value (even the same value as before) or clearing the reference will always
trigger a reallocation of the Iub link control.
Dependencies: This attribute should not be changed in the same
transaction as controlPlaneTransportOption.
If userPlaneTransportOption.atm==TRUE, this attribute must contain a
valid reference.
If userPlaneTransportOption.atm==FALSE, the value of this attribute is not
used.

IubLink

cachedRemoteCpIpAddress1

RNC

Latest IP address received from the DNS, when remoteCpIpaddress1 is set string
to a domain name.
Before a value is received from the DNS, the value of this attribute is ""
(empty string).
Dependencies: Set to an empty string when remoteCpIpaddress1 is
changed, except when changing from one domain name to another.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IubLink

cachedRemoteCpIpAddress2

RNC

Network Parameters

106 (520)

Latest IP address received from the DNS, when remoteCpIpaddress2 is set string
to a domain name.
Before a value is received from the DNS, the value of this attribute is ""
(empty string).
Dependencies: Set to an empty string when remoteCpIpaddress2 is
changed, except when changing from one domain name to another.

IubLink

controlPlaneTransportOption

RNC

Transport option for the NBAP signaling bearers for this IubLink instance.
One and only one of the flags must be set to TRUE.

TransportOptionDef

Takes effect: At unlock of IubLink


Dependencies: This attribute should not be changed in the same
transaction as atmUserPlaneTermSubrackRef.
This IubLink must be locked, and must have been locked
(administrativeState = LOCKED) in an earlier transaction, in order to
change the value of this attribute.
When setting controlPlaneTransportOption.ipv4=TRUE, at least one Sctp
MO must be configured for Iub. This Sctp will be reserved by the IubLink
(through the attribute sctpRef). Also, remoteCpIpAddress1 must be set to a
valid value. If remoteCpIpAddress2 is set to a valid value, that value may
also be used.

IubLink

controlPlaneTransportOption.atm

RNC

Controls if ATM is enabled in the transport layer.

BooleanVals

FALSE = 0
TRUE = 1
FALSE = 0
TRUE = 1

IubLink

controlPlaneTransportOption.ipv4

RNC

Controls if IPv4 is enabled in the transport layer.

BooleanVals

IubLink

l2EstReqRetryTimeNbapC

RNC

Time between successive attempts to establish layer 2 signaling bearers


for NBAP Common.

long

1..150

long

1..150

Takes effect: Immediately


Unit: s
IubLink

l2EstReqRetryTimeNbapD

RNC

Time between successive attempts to establish layer 2 signaling bearers


for NBAP Dedicated.
Takes effect: Immediately
Unit: s

IubLink

remoteCpIpAddress1

RNC

Primary identifier for the control plane IP host of the RBS. Contains either string
the domain name or the IP address of the control plane IP host.
For a domain name, the input format is a series of alphanumeric
characters, hyphens and periods. Hyphens and periods cannot be placed
at the beginning or end of the name. The domain name is case-insensitive.
For a numeric IP address, the input format is four fields of digits, separated
by dots. Each field may consist of three digits. The value of each field shall
be in the range 0..255.
The value of remoteCpIpAddress1 should be unique within the RNC, since
it is used to contact the IP host on a single individual RBS.
Takes effect: Immediately
Dependencies: If controlPlaneTransportOption.ipv4=TRUE, this attribute
must be set to a valid value.
This attribute is only used if controlPlaneTransportOption.ipv4=TRUE.
remoteCpIpAddress1 and remoteCpIpAddress2 should not be set to the
same value, since each represents a separate IP host in the RBS.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IubLink

remoteCpIpAddress2

RNC

Network Parameters

107 (520)

Secondary identifier for the control plane IP host of the RBS. Contains
string
either the domain name or the IP address of the control plane IP host.
Only used if the RBS is multi-homed.
For a domain name, the input format is a series of alphanumeric
characters, hyphens and periods. Hyphens and periods cannot be placed
at the beginning or end of the name. The domain name is case-insensitive.
For a numeric IP address, the input format is four fields of digits, separated
by dots. Each field may consist of three digits. The value of each field shall
be in the range 0..255.
The value of remoteCpIpAddress2 should be unique within the RNC, since
it is used to contact the IP host on a single individual RBS.
Takes effect: Immediately
Dependencies: This attribute is only used if
controlPlaneTransportOption.ipv4=TRUE.
remoteCpIpAddress1 and remoteCpIpAddress2 should not be set to the
same value, since each represents a separate IP host in the RBS.

IubLink

sctpRef

RNC

IubLink

softCongThreshGbrBwDl

RNC

Reference to the Sctp instance used.

Sctp

Dependencies: Only used if controlPlaneTransportOption.ipv4=TRUE.


Downlink soft congestion threshold in percent of the configured Iub
bandwidth (userPlaneGbrAdmBandwidthDl including
userPlaneGbrAdmMarginDl).

long

0..100

100

Uplink soft congestion threshold in percent of the configured Iub bandwidth long
(userPlaneGbrAdmBandwidthUl including userPlaneGbrAdmMarginUl).

0..100

100

Takes effect: New connections


Unit: %
IubLink

softCongThreshGbrBwUl

RNC

Takes effect: New connections


Unit: %
IubLink

userPlaneGbrAdmBandwidthDl

RNC

Maximum downlink transmission bandwidth on this IubLink that can be


long
used by GBR RABs when the Iub GBR admission control feature is active.
The bandwith for IP transport includes UDP/IP/Ethernet overhead; likewise,
the bandwidth for ATM transport includes AAL2/ATM overhead. This value
is used by TN Connection Admission Control to calculate the downlink
bandwidth limit used for admission, which is (in kbps) 100 *
userPlaneGbrAdmBandwidthDl * (1 + userPlaneGbrAdmMarginDl / 100).
If the Dual Stack Iub feature is configured (both ATM and IP have been
configured in userPlaneTransportOption), then all GBR services must be
configured with the same transport option, either ATM or IP, for the
admission control function to work properly.
The bandwidth should always be set to less than or equal to the physical
Iub bandwidth.

1..10000

10000

Takes effect: New connections


Unit: 100 kbps

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IubLink

userPlaneGbrAdmBandwidthUl

RNC

Network Parameters

Maximum uplink transmission bandwidth on this IubLink that can be used long
by GBR RABs when the Iub GBR admission control feature is active. The
bandwith for IP transport includes UDP/IP/Ethernet overhead; likewise, the
bandwidth for ATM transport includes AAL2/ATM overhead. This value is
used by TN Connection Admission Control to calculate the uplink
bandwidth limit used for admission, which is (in kbps) 100 *
userPlaneGbrAdmBandwidthUl * (1 + userPlaneGbrAdmMarginUl / 100).
If the Dual Stack Iub feature is configured (both ATM and IP have been
configured in userPlaneTransportOption), then all GBR services must be
configured with the same transport option, either ATM or IP, for the
admission control function to work properly.
The bandwidth should always be set to less than or equal to the physical
Iub bandwidth.

108 (520)
1..10000

10000

Takes effect: New connections


Unit: 100 kbps

IubLink

userPlaneGbrAdmEnabled

RNC

Activates the Iub GBR admission control feature for GBR transport bearers. BooleanVals
The GBR transport bearers affected by this feature are:
- Conversational transport bearers
- Streaming transport bearers
- Transport bearers for RRC connection setup
- All Common (TrCh) transport bearers

FALSE = 0
TRUE = 1

FALSE(0)

Takes effect: New connections

IubLink

userPlaneGbrAdmMarginDl

RNC

Margin to which this Iub link is over- or underbooked in the downlink, when long
the Iub GBR admission control feature is active. Expressed relative to the
value of userPlaneGbrAdmBandwidthDl. This value is used by TN
Connection Admission Control to calculate the downlink bandwidth limit
used for admission, which is (in kbps) 100 * userPlaneGbrAdmBandwidthDl
* (1 + userPlaneGbrAdmMarginDl / 100). If the Iub link is overbooked, then
the probablility of overloading the Iub link is increased, whereas if the Iub
link is underbooked, the chance of overload is reduced, but at the expense
of rejecting more RL setup/reconfigurations.

-99..99

-99..99

Takes effect: New connections


Unit: %

IubLink

userPlaneGbrAdmMarginUl

RNC

Margin to which this Iub link is over- or underbooked in the uplink, when the long
Iub GBR admission control feature is active. Expressed relative to the value
of userPlaneGbrAdmBandwidthUl. This value is used by TN Connection
Admission Control to calculate the uplink bandwidth limit used for
admission, which is (in kbps) 100 * userPlaneGbrAdmBandwidthUl * (1 +
userPlaneGbrAdmMarginUl / 100). If the Iub link is overbooked, then the
probablility of overloading the Iub link is increased, whereas if the Iub link is
underbooked, the chance of overload is reduced, but at the expense of
rejecting more RL setup/reconfigurations.
Takes effect: New connections
Unit: %

IubLink

userPlaneIpResourceRef

RNC

Local user plane IP resource(s) available for the Iub interface.

IpAccessHostPool

Dependencies: This attribute must contain a valid reference if


userPlaneTransportOption.ipv4 = TRUE.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IubLink

userPlaneTransportOption

RNC

Network Parameters

109 (520)

User plane transport option for the Iub interface.


TransportOptionDef
At least one of the flags must be set to TRUE. If both flags are set to TRUE
(meaning dual stack is configured), but the dual stack feature has not been
activated, then ATM will be used as the transport option.
Takes effect: New connections
Dependencies: userPlaneIpResourceRef must contain a valid reference if
userPlaneTransportOption.ipv4 = TRUE.

IubLink

userPlaneTransportOption.atm

RNC

Controls if ATM is enabled in the transport layer.

BooleanVals

IubLink

userPlaneTransportOption.ipv4

RNC

Controls if IPv4 is enabled in the transport layer.

BooleanVals

IuLink

atmUserPlaneTermSubrackRef

RNC

Reference to the subrack where the ATM user plane termination of the Iu
link is located, and from which the Iur link should preferably be controlled.
The Iu link control location should be selected to minimize inter-subrack
communication during traffic handling and thus reduce overhead.
This attribute is only used in ATM transport and in RNC product versions
with an ATM switch core.

Subrack

FALSE = 0
TRUE = 1
FALSE = 0
TRUE = 1

Dependencies: Only used if userPlaneTransportOption.atm==TRUE and


RncFunction::intraNodeIpResourceRef is not empty.

IuLink
IuLink

IuLinkId
packetDataRouterRef

RNC
RNC

Naming attribute. Contains the value part of the RDN.


string
List of references to the instances of MO PacketDataRouter or MO
ManagedObject
IpEthPacketDataRouter that may be selected when establishing a PS
connection to the CN node represented by this IuLink. Used to control
which PDR devices can be used for PS traffic towards this specific CN
node.
If there is more than one CN node in the PS domain, the Iu flex feature
should be activated through the attribute
RncFunction::networkResourceIdentifierLengthPs. Then, if this IuLink is not
inter-connected with all available PDR devices defined in this RNC,
packetDataRouterRef should contain references to the corresponding
PacketDataRouter or IpEthPacketDataRouter MOs pointing to this CN
node. The RNC then selects one among the referenced MOs to use for PS
traffic for this IuLink.
If the CN node represented by this IuLink is inter-connected with all PDR
devices defined in this RNC, this attribute can be left empty. The RNC will
then select one among all the available
PacketDataRouter/IpEthPacketDataRouter MOs defined in the RNC to use
for PS traffic for this IuLink.
Sequence length must be in the range 0..20
Dependencies: This attribute is only used if a child Ranap MO exists with
cnDomainInd = PACKET_SWITCHED.

IuLink

userLabel

RNC

IuLink

userPlaneIpResourceRef

RNC

Provides the possibility to put a user-friendly label on the MO instance. The string
value is not used by the RNC.
Local user plane IP resource(s) available for this IuLink.
IpAccessHostPool
Takes effect: Immediately
Dependencies: If Ranap::cnDomainInd==CIRCUIT_SWITCHED and
userPlaneTransportOption.ipv4==TRUE, userPlaneIpResourceRef must
contain a valid reference.
Otherwise, userPlaneIpResourceRef is not used by the system and does
not need to be set.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
IuLink

userPlaneTransportOption

RNC

Network Parameters

User plane transport option for this IuLink.


At least one of the flags must be set to TRUE.

110 (520)

TransportOptionDef

Takes effect: Immediately


Dependencies: If Ranap::cnDomainInd==CIRCUIT_SWITCHED and
userPlaneTransportOption.ipv4==TRUE, userPlaneIpResourceRef must
contain a valid reference.
Otherwise, userPlaneIpResourceRef is not used by the system and does
not need to be set.
IuLink

userPlaneTransportOption.atm

RNC

Controls if ATM is enabled in the transport layer.

BooleanVals

IuLink

userPlaneTransportOption.ipv4

RNC

Controls if IPv4 is enabled in the transport layer.

BooleanVals

IurLink

atmUserPlaneTermSubrackRef

RNC

Reference to the subrack where the ATM user plane termination of the Iur
link is located, and from which the Iur link should preferably be controlled.
The Iur link control location should be selected to minimize inter-subrack
communication during traffic handling and thus reduce overhead.
This attribute is only used in ATM transport and in RNC product versions
with an ATM switch core.

Subrack

FALSE = 0
TRUE = 1
FALSE = 0
TRUE = 1

Dependencies: Only used if userPlaneTransportOption.atm==TRUE and


RncFunction::intraNodeIpResourceRef is not empty.

IurLink

userPlaneIpResourceRef

RNC

Local user plane IP resource(s) available for the Iur interface. Setting
reference to local user plane IP resources is mandatory if
userPlaneTransportOption.ipv4 is TRUE.

IpAccessHostPool

IurLink

userPlaneTransportOption

RNC

User plane transport option for the Iur interface. One and only one of the
flags have to be set to TRUE.

TransportOptionDef

Takes effect: Connection on a new transport bearer


Dependencies: If userPlaneTransportOption.ipv4 is TRUE then
userPlaneIpResourceRef is mandatory.
IurLink

userPlaneTransportOption.atm

RNC

Controls if ATM is enabled in the transport layer.

BooleanVals

IurLink

userPlaneTransportOption.ipv4

RNC

Controls if IPv4 is enabled in the transport layer.

BooleanVals

J1PhysPathTerm

administrativeState

RBS DUW

The administrative state.

AdmState

J1PhysPathTerm

administrativeState

RNC

The administrative state.

AdmState

J1PhysPathTerm

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

FALSE = 0
TRUE = 1
FALSE = 0
TRUE = 1
LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2
LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

LOCKED(0)

true - reporting enabled.


false - reporting disabled.
J1PhysPathTerm

aisReporting

RNC

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
J1PhysPathTerm

availabilityStatus

RBS DUW

Network Parameters

The availability status.

111 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

J1PhysPathTerm

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

J1PhysPathTerm

degThreshold

RBS DUW

Specifies the Bit Error Rate (BER) threshold for the Degraded Signal (DEG) long
alarm.

3..9

3..9

The value of this attribute gives a BER of 10 raised to the power of -X,
where X is the value of degThreshold.
If the threshold is exceeded, a Degraded Signal (DEG) alarm is issued.
J1PhysPathTerm

degThreshold

RNC

Specifies the Bit Error Rate (BER) threshold for the Degraded Signal (DEG) long
alarm.
The value of this attribute gives a BER of 10 raised to the power of
-X, where X is the value of degThreshold.
If the threshold is exceeded, a Degraded Signal (DEG) alarm is
issued.

J1PhysPathTerm

idlePattern

RBS DUW

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but setting


up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED -> A_LAW.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
J1PhysPathTerm

idlePattern

RNC

Network Parameters

112 (520)

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but


setting up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED ->
A_LAW.

J1PhysPathTerm
J1PhysPathTerm

J1PhysPathTermId
J1PhysPathTermId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

J1PhysPathTerm
J1PhysPathTerm

lineNo
lineNo

RBS DUW
RNC

The line number on the board.


The line number on the board.

long
long

J1PhysPathTerm

loopback

RBS DUW

The loopback state of this physical path termination.

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
J1_G = 0
J1_I = 1
J1_G = 0
J1_I = 1

1..8
1..8

The attribute administrativeState must be set to LOCKED when setting the


attribute loopback.
J1PhysPathTerm

loopback

RNC

The loopback state of this physical path termination.


The attribute administrativeState must be set to LOCKED when
setting the attribute loopback.

J1PhysPathTerm

operationalState

RBS DUW

The operational state.

OperState

J1PhysPathTerm

operationalState

RNC

The operational state.

OperState

J1PhysPathTerm

physicalLineType

RBS DUW

Indicates the supported physical line interface.

J1Type

J1PhysPathTerm

physicalLineType

RNC

Indicates the supported physical line interface.

J1Type

J1PhysPathTerm

rdiReporting

RBS DUW

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

J1_G(0)
J1_G(0)
0

true - reporting enabled.


false - reporting disabled.
J1PhysPathTerm

rdiReporting

RNC

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
J1PhysPathTerm
J1PhysPathTerm

reservedByImaLink
reservedByImaLink

RBS DUW
RNC

The identity of the ImaLink MO that reserves this MO instance.


The identity of the ImaLink MO that reserves this MO instance.

ImaLink
ImaLink

J1PhysPathTerm

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

J1PhysPathTerm

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

J1PhysPathTerm
J1PhysPathTerm

reservedByTraffic
reservedByTraffic

RBS DUW
RNC

The identity of the AtmPort MO that reserves this MO instance.


The identity of the AtmPort MO that reserves this MO instance.

AtmPort
AtmPort

J1PhysPathTerm

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
J1PhysPathTerm

shutDownTimeout

RNC

Network Parameters

The shut-down timer.

long

113 (520)
0..100000

1800

It is used when the administrativeState is set to


SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s
J1PhysPathTerm
J1PhysPathTerm

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Lag

requiredNumberOfLinks

RBS DUW

Specifies the number of Ethernet links that need to be operational in order long
for the LAG to be operational.
Unit: 1 links

0..12

Lag

requiredNumberOfLinks

RNC

Specifies the number of Ethernet links that need to be operational in order long
for the LAG to be operational.
Unit: 1 links

0..12

M3uaRemoteSp
M3uAssociation

sctpAssociationRef
associationState

RNC
RNC

Reference to SCTP association.


The state of the M3UA association.

SctpAssociation
long

Possible values:
0x01 (1) INACTIVE
0x02 (2) ACTIVE
0x04 (4) ESTABLISHED
0x08 (8) DOWN
These values are mutually exclusive.
M3uAssociation

autoStartAssociation

RNC

Specifies if the M3UA association is started automatically.

boolean

1 TRUE(1)

Applicable only if the attribute role is set to CLIENT. That is, the
M3UA association is never started if its role is SERVER.
M3uAssociation

congestionAlarmThreshold

RNC

Specifies the accumulated time limit the M3UA association is allowed to be long
congested before an alarm is issued.

0..750

50

0..63

50

If set to 0, the alarm is issued immediately.


Unit: 1 decisecond (1/10 second)
M3uAssociation

dscp

RNC

The DSCP, Differentiated Services Code Point, for the internal M3UA user, long
to use for signaling traffic in the IP network.
The DSCP value must be the same for all M3UA associations
sharing the same SCTP host and local port number. This means that if
dscp=10 is set for a group of M3uAssociations with localPortNumber=2905
on one SCTP host, a different DSCP value can be set for a group of
M3uAssociations with another localPortNumber on that SCTP host.
Using the localIPMask it is possible to have several different DSCP
values in the same SCTP MO instance, one for each unique combination of
local IP address and local port number.
The value of this attribute specified in the first instance of
M3uAssociation created under a signalling point, is also used for all other
M3uAssociation instances created under the same signalling point. That is,
the value of this attribute specified in the other instances has no effect.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
M3uAssociation

localIpMask

RNC

Network Parameters

The homing state of the local SCTP endpoint of the M3UA association.

114 (520)

HomingState

SINGLE_HOMED_1 = 1
SINGLE_HOMED_2 = 2
MULTI_HOMED = 3

Specifies whether single- or multi-homing is used.

MULTI_HOMED(3)

If the attribute ipAccessHostGpbId in the Sctp MO contains a value


and:
- if set to SINGLE_HOMED_1, the attributes ipAddress1 or
autoConfigIdentity in the IpAccessHostGpb MO must be defined.
- if set to SINGLE_HOMED_2, the attributes ipAddress2 or
autoConfigIdentity2 in the IpAccessHostGpb MO must be defined.
- if set to MULTI_HOMED, the requirements for both
SINGLE_HOMED_1 and SINGLE_HOMED_2 must be fulfilled.
If the attribute ipAccessSctpRef in the Sctp MO contains a value
and:
- if set to SINGLE_HOMED_1, the attribute ipAccessHostEtRef1 in
the IpAccessSctp MO must be defined.
- if set to SINGLE_HOMED_2, the attribute ipAccessHostEtRef2 in
the IpAccessSctp MO must be defined.
- if set to MULTI_HOMED, the requirements for both
SINGLE_HOMED_1 and SINGLE_HOMED_2 must be fulfilled.

M3uAssociation

localPortNumber

RNC

The port number of the local SCTP endpoint of the M3UA association.

long

1..65535

2905

The SCTP Registered User Port Number Assignment for M3UA is


2905 according to the standard specification.
Specification: RFC 4666
M3uAssociation

M3uAssociationId

RNC

The value component of the RDN.

string

M3uAssociation

mtp3bSrsId

RNC

Reference to an instance of Mtp3bSrs, specifying the adjacent node of the Mtp3bSrs


M3UA association.

M3uAssociation

operationalState

RNC

The operational state.

OperState

See CPI

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the signalling process


represented by this MO is in state ASP-ACTIVE. That is, the attribute
associationState is ACTIVE.
M3uAssociation

remoteIpAddress1

RNC

The remote IP address 1.

string

This address is considered as the primary IP address. In case the


association establishment attempt fails when using this IP address, the
remote IP address 2 will be used for the next attempt.
The range is 0.0.0.0 ? 255.255.255.255.
If set to "", it means that the IP address is not specified.
This address cannot be the same as remoteIpAddress2.

M3uAssociation

remoteIpAddress2

RNC

The remote IP address 2.

string

In case the association establishment attempt fails when using this


IP address, the remote IP address 1 will be used for the next attempt.
The range is 0.0.0.0 ? 255.255.255.255.
If set to "", it means that the IP address is not specified.
This address cannot be the same as remoteIpAddress1.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
M3uAssociation

remotePortNumber

RNC

Network Parameters

The port number of the remote SCTP endpoint of the M3UA association.

long

115 (520)
0..65535

2905

If the role of the M3UA association is set to SERVER, association


establishment requests are accepted from any remote port number. In this
case, this attribute is not used and can be set to 0.

M3uAssociation

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

Mtp3bSr

M3uAssociation

role

RNC

Indicates if the association is to operate as CLIENT or SERVER. The ASP M3uAssociationRole


messaging will be set to ON for a CLIENT and to OFF for a SERVER.

CLIENT = 0
SERVER = 1

CLIENT(0)

CLIENT(0)

If the role is set to CLIENT, the association operates as CLIENTPEER. That is, it acts as CLIENT, but accepts if the peer side also acts as
CLIENT.
The roles must be coordinated between peers. The following
configurations are supported:
- CLIENT - SERVER,
- CLIENT - CLIENT.

M3uAssociation
M3uAssociation

sctpAssociationRef
sctpId

RNC
RNC

Reference to SCTP association.


Reference to an instance of Sctp MO, which represents the SCTP host.

SctpAssociation
Sctp

See CPI

M3uAssociation can refer to Sctp MO if following conditions are


fulfilled for this Sctp MO:
- ipAccessHostGpbId is set, or
- ipAccessSctpRef is set and corresponding IpAccessSctp MO does
not support port distribution.
M3uAssociation

userLabel

RNC

Label for free use.

string

ManagedElementData

documentServerAddress

RBS DUW

The base URL for the documentation server.

string

The attribute is read by the Element Management application to find the


documentation server in the network. The URL shall contain the document
server, for example:
http://cpi2.al.sw.ericsson.se/alexserv
The syntax "http://cpi.al.sw.ericsson.se/alexserv?LI=EN/LZN7450008R2A"
is deprecated, and will not be supported in a future release. Please use the
attribute docLibUserDefined if docLibSystemDefined is not available.

ManagedElementData

documentServerAddress

RNC

The base URL for the documentation server.

string

The attribute is read by the Element Management application to


find the documentation server in the network. The URL shall contain the
document server, for example:
http://cpi2.al.sw.ericsson.se/alexserv
The syntax "http://cpi.al.sw.ericsson.se/alexserv?
LI=EN/LZN7450008R2A" is deprecated, and will not be supported in a
future release. Please use the attribute docLibUserDefined if
docLibSystemDefined is not available.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

logonServerAddress

RBS DUW

Network Parameters

116 (520)

A list of node names or IP addresses of the single logon servers (SLSs).


string
The list uses commas to seperate the single logon server addresses, e.g.
"https://SLS1,https://SLS2,https://SLS3", these addresses consists of the
URLs to the concerned SLS servers. Maximum of 3 SLSs are supported.
The attribute is read by Element Management application to find the single
logon server in the network.
The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification RFC
4291, chapter 2.2, bullet 1 and 2.
The input format for a domain name is as defined in specification RFC 952.
When address resolution is requested and the DNS server responds with a
list of resolved addresses, the first address presented by the DNS server is
used by this attribute.
Note that you need to configure a name-to-IP-address association in the
DNS server, with an address that belongs to the correct address family. If
the node is configured for OAM IP connectivity over IPv6, the address in
the DNS association must be an IPv6 address.
Complete URLs with the above examples:
http://[2001:db8:0::1]:8080/cgi-bin/pkiclient.exe

ManagedElementData

logonServerAddress

RNC

A list of node names or IP addresses of the single logon servers (SLSs).


string
The list uses commas to seperate the single logon server addresses, e.g.
"https://SLS1,https://SLS2,https://SLS3", these addresses consists of the
URLs to the concerned SLS servers. Maximum of 3 SLSs are supported.
The attribute is read by Element Management application to find the single
logon server in the network.
The input format for an IPv4 address is four fields of digits,
separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC 4291, chapter 2.2, bullet 1 and 2.
The input format for a domain name is as defined in specification
RFC 952.
When address resolution is requested and the DNS server
responds with a list of resolved addresses, the first address presented by
the DNS server is used by this attribute.
Note that you need to configure a name-to-IP-address association
in the DNS server, with an address that belongs to the correct address
family. If the node is configured for OAM IP connectivity over IPv6, the
address in the DNS association must be an IPv6 address.
Complete URLs with the above examples:
http://[2001:db8:0::1]:8080/cgi-bin/pkiclient.exe

ManagedElementData

ntpBurstFlagPrimary

RBS DUW

This is the burst flag used towards the primary NTP server.

boolean

0 FALSE(0)

boolean

FALSE(0)

Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpBurstFlagPrimary

RNC

This is the burst flag used towards the primary NTP server.
Even if this NTP server is not configured, this attribute still responds
with its default value.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpBurstFlagSecondary

RBS DUW

Network Parameters

This is the burst flag used towards the secondary NTP server.

117 (520)

boolean

FALSE(0)

boolean

FALSE(0)

boolean

FALSE(0)

boolean

FALSE(0)

Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpBurstFlagSecondary

RNC

This is the burst flag used towards the secondary NTP server.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpBurstFlagThird

RBS DUW

This is the burst flag used towards the third NTP server.
Even if this NTP server is not configured, this attribute still responds with its
default value.

ManagedElementData

ntpBurstFlagThird

RNC

This is the burst flag used towards the third NTP server.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpMaxPollPrimary

RBS DUW

This value states the maximum interval (in seconds) for polling the primary long
NTP server.

16..131072

1024

1024

16..131072

1024

1024

long

16..131072

1024

1024

long

16..131072

1024

1024

long

16..131072

1024

1024

long

16..131072

1024

1024

This value must be > 0.


Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpMaxPollPrimary

RNC

This value states the maximum interval (in seconds) for polling the primary long
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpMaxPollSecondary

RBS DUW

This value states the maximum interval (in seconds) for polling the
secondary NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds with its
default value.

ManagedElementData

ntpMaxPollSecondary

RNC

This value states the maximum interval (in seconds) for polling the
secondary NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpMaxPollThird

RBS DUW

This value states the maximum interval (in seconds) for polling the third
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds with its
default value.

ManagedElementData

ntpMaxPollThird

RNC

This value states the maximum interval (in seconds) for polling the third
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpMinPollPrimary

RBS DUW

Network Parameters

This value states the minimum interval (in seconds) for polling the primary
NTP server.

118 (520)

long

16..131072

64

64

long

16..131072

64

64

long

16..131072

64

64

long

16..131072

64

64

long

16..131072

64

64

long

16..131072

64

64

This value must be > 0.


Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpMinPollPrimary

RNC

This value states the minimum interval (in seconds) for polling the primary
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpMinPollSecondary

RBS DUW

This value states the minimum interval (in seconds) for polling the
secondary NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds with its
default value.

ManagedElementData

ntpMinPollSecondary

RNC

This value states the minimum interval (in seconds) for polling the
secondary NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpMinPollThird

RBS DUW

This value states the minimum interval (in seconds) for polling the third
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds with its
default value.

ManagedElementData

ntpMinPollThird

RNC

This value states the minimum interval (in seconds) for polling the third
NTP server.
This value must be > 0.
Even if this NTP server is not configured, this attribute still responds
with its default value.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpServerAddressPrimary

RBS DUW

Network Parameters

This is the IP address to the NTP server.

119 (520)

string

If this NTP server is not configured, this attribute responds with 0.0.0.0.
The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification RFC
4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification RFC 952.
When address resolution is requested and the DNS server responds with a
list of resolved addresses, the first address presented by the DNS server is
used by this attribute.
Note that you need to configure a name-to-IP-address association in the
DNS server, with an address that belongs to the correct address family. If
the node is configured for OAM IP connectivity over IPv6, the address in
the DNS association must be an IPv6 address.

ManagedElementData

ntpServerAddressPrimary

RNC

This is the IP address to the NTP server.

string

If this NTP server is not configured, this attribute responds with


0.0.0.0.
The input format for an IPv4 address is four fields of digits,
separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC 4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification
RFC 952.
When address resolution is requested and the DNS server
responds with a list of resolved addresses, the first address presented by
the DNS server is used by this attribute.
Note that you need to configure a name-to-IP-address association
in the DNS server, with an address that belongs to the correct address
family. If the node is configured for OAM IP connectivity over IPv6, the
address in the DNS association must be an IPv6 address.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpServerAddressSecondary

RBS DUW

Network Parameters

This is an alternative IP address to an NTP server.

120 (520)

string

If this NTP server is not configured, this attribute responds with 0.0.0.0.
The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification RFC
4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification RFC 952.
When address resolution is requested and the DNS server responds with a
list of resolved addresses, the first address presented by the DNS server is
used by this attribute.
Note that you need to configure a name-to-IP-address association in the
DNS server, with an address that belongs to the correct address family. If
the node is configured for OAM IP connectivity over IPv6, the address in
the DNS association must be an IPv6 address.

ManagedElementData

ntpServerAddressSecondary

RNC

This is an alternative IP address to an NTP server.

string

If this NTP server is not configured, this attribute responds with


0.0.0.0.
The input format for an IPv4 address is four fields of digits,
separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC 4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification
RFC 952.
When address resolution is requested and the DNS server
responds with a list of resolved addresses, the first address presented by
the DNS server is used by this attribute.
Note that you need to configure a name-to-IP-address association
in the DNS server, with an address that belongs to the correct address
family. If the node is configured for OAM IP connectivity over IPv6, the
address in the DNS association must be an IPv6 address.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpServerAddressThird

RBS DUW

Network Parameters

This is an alternative IP address to an NTP server.

121 (520)

string

If this NTP server is not configured, this attribute responds with 0.0.0.0.
The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification RFC
4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification RFC 952.
When address resolution is requested and the DNS server responds with a
list of resolved addresses, the first address presented by the DNS server is
used by this attribute.
Note that you need to configure a name-to-IP-address association in the
DNS server, with an address that belongs to the correct address family. If
the node is configured for OAM IP connectivity over IPv6, the address in
the DNS association must be an IPv6 address.

ManagedElementData

ntpServerAddressThird

RNC

This is an alternative IP address to an NTP server.

string

If this NTP server is not configured, this attribute responds with


0.0.0.0.
The input format for an IPv4 address is four fields of digits,
separated by a dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC 4291, chapter 2.2, bullet 1 and 2.
Domain names are supported.
The input format for a domain name is as defined in specification
RFC 952.
When address resolution is requested and the DNS server
responds with a list of resolved addresses, the first address presented by
the DNS server is used by this attribute.
Note that you need to configure a name-to-IP-address association
in the DNS server, with an address that belongs to the correct address
family. If the node is configured for OAM IP connectivity over IPv6, the
address in the DNS association must be an IPv6 address.

ManagedElementData

ntpServiceActivePrimary

RBS DUW

Specifies if the node should poll the primary NTP server for information.

boolean

0 TRUE(1)

boolean

TRUE(1)

Specifies if the node should poll the secondary NTP server for information. boolean

TRUE(1)

Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpServiceActivePrimary

RNC

Specifies if the node should poll the primary NTP server for information.
Even if this NTP server is not configured, this attribute still responds
with its default value.

ManagedElementData

ntpServiceActiveSecondary

RBS DUW

Even if this NTP server is not configured, this attribute still responds with its
default value.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
ManagedElementData

ntpServiceActiveSecondary

RNC

Network Parameters

122 (520)

Specifies if the node should poll the secondary NTP server for information. boolean

TRUE(1)

Even if this NTP server is not configured, this attribute still responds
with its default value.
ManagedElementData

ntpServiceActiveThird

RBS DUW

Specifies if the node should poll the third NTP server for information.

boolean

FALSE(0)

boolean

FALSE(0)

Even if this NTP server is not configured, this attribute still responds with its
default value.
ManagedElementData

ntpServiceActiveThird

RNC

Specifies if the node should poll the third NTP server for information.
Even if this NTP server is not configured, this attribute still responds
with its default value.

Mspg

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.

Mspg

degCauseMsp

RNC

Defines whether a degraded signal (DEG) defect should cause an


automatic MSP switch.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

boolean

This attribute applies to the ETSI standard.


Mspg

lockout

RNC

If lockout is set to true, the MSP logic is frozen meaning that no MSP
switch occur, regardless of what happens on the lines. The APS (K1KL2)
signalling also continues to signal the request and/or responses that it did
when the set operation was perfomed.

boolean

This attribute applies when an HG channelized STM-1 TTC


interface is used.
Mspg

MspgId

RNC

The value component of the RDN.

string

Mspg

operationalState

RNC

The operational state.

OperState

Mspg

os155SpiStandbyId

RNC

The standby OS155 physical path termination.

Os155SpiTtp

Mspg

os155SpiWorkingId

RNC

The working OS155 physical path termination.

Os155SpiTtp

Mspg

primarySection

RNC

The primary section indicates the Os155SpiTtp that currently has the role
of primary interface.
As a consequence of a completed MSP switch, the primary and
secondary sections can be interchanged.

Os155SpiTtp

DISABLED = 0
ENABLED = 1

This attribute applies to the STM-1 Channelized TTC case.


Mspg

rdiSecondarySf

RNC

Specifies if MSPG should prevent an MSP switch, if MS-RDI is present on boolean


the secondary section.

This attribute applies to the STM-1 Channelized TTC case.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mspg

selectedBoard

RNC

Network Parameters

123 (520)

The ExchangeTerminal MO that is currently used to process the user plane ManagedObject
traffic.
The only action that can change the selected board is an equipment
protection switch.

Mspg

selectedPort

RNC

The port currently selected by the MSPG. The selected port can change
only as a result of an MSP switch or an equipment protection switch.

Os155SpiTtp

Mspg

switchMode

RNC

The switching mode. Two values are possible:

SwitchModes

AUTOMATIC = 0
LOCKED = 1

AUTOMATIC(0)

switchMode = LOCKED if any of the involved Os155SpiTtp MOs is


locked (or is indirectly locked from the PlugInUnit MO).
switchMode = AUTOMATIC in all other cases.
Mspg

userLabel

RNC

Label for free use.

string

MspgExtended

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.

MspgExtended

bidirectional

RNC

Specifies the switching type of the MSP.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

boolean

true = bidirectional mode


false = unidirectional mode
MspgExtended

MspgExtendedId

RNC

The value component of the RDN.

string

MspgExtended

opBidirectionalMode

RNC

Indicates the operational switching type of the MSP.

boolean

It differs from the value of the attribute bidirectional if:


- the standardMode of the os155SpiWorkingRef is ANSI,
- bidirectional is true, and
- the remote side does not support bidirectional switching mode.
If the local side is set to bidirectional, and the remote side does not
support bidirectional MSP, then this attribute changes to false.
true = bidirectional mode
false = unidirectional mode

MspgExtended

operationalState

RNC

The operational state.

OperState

MspgExtended

os155SpiProtectionRef

RNC

Reference to an instance of Os155SpiTtp MO.

Os155SpiTtp

DISABLED = 0
ENABLED = 1

The protection OS155 physical path termination.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
MspgExtended

os155SpiWorkingRef

RNC

Network Parameters

Reference to an instance of Os155SpiTtp MO.

124 (520)

Os155SpiTtp

The working OS155 physical path termination.


MspgExtended

protectionStatus

RNC

Indicates the status of the protection switch.

ProtectionStatus

MspgExtended

revertive

RNC

Specifies whether the MSP is revertive or non-revertive.

boolean

NO_REQUEST = 0
MANUAL_SWITCH_COMPLETED =
1
FAILURE_OF_PROTOCOL = 2
AUTOMATIC_SF_COMPLETED = 3
AUTOMATIC_SD_COMPLETED = 4
WAIT_TO_RESTORE = 5
FORCE_SWITCH_COMPLETED = 6
LOCKOUT_COMPLETED = 7
DO_NOT_REVERT = 8

true = revertive
false = non-revertive
MspgExtended

selectedBoard

RNC

The ExchangeTerminal MO that is currently used to process the user plane ManagedObject
traffic.
The only action that can change the selected board is an equipment
protection switch.

MspgExtended

selectedPort

RNC

The port currently selected by the MSPG.

Os155SpiTtp

The selected port can change only as a result of an MSP switch or


an equipment protection switch.
MspgExtended

userLabel

RNC

Label for free use.

string

MspgExtended

waitToRestoreTime

RNC

Represents the time that the working section must be fault-free before
switching back from the protection section.

long

Mtp3bAp

availabilityStatus

RNC

The availability status.

5..12

Unit: 1 min
AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
- DEGRADED: the corresponding destination is congested.
- OFF_DUTY: The ASP Active procedure can not be started for the
related application server until a client is ready to receive the traffic. The
access point is kept ENABLED to allow a client to attach, but traffic
sending/receiving is not allowed on this access point.
This state is applicable only for an IETF M3UA configuration.

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

Possible values for operational state DISABLED:


- DEPENDENCY_LOCKED, DEPENDENCY_FAILED,
DEPENDENCY_SHUTTINGDOWN: these values are based on the
administrative state and the availability status of the M3uaLocalAs and
Mtp3bSrs instances related to this access point.
- FAILED: the MO has other reasons for staying DISABLED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Mtp3bAp

Mtp3bApId

RNC

The value component of the RDN.

string

Mtp3bAp

operationalState

RNC

The operational state.

OperState

125 (520)

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the client is allowed to send


traffic.
Mtp3bAp

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

Mtp3bAp

routeSetId

RNC

Reference to an instance of Mtp3bSrs MO.

Mtp3bSrs

Specifies the destination for the traffic from the client.


Mtp3bAp

serviceInd

RNC

The service indicator.

long

3..15

See CPI

Specifies the Service Indicator (SI) of the client, which is used in


outgoing messages and is used by traffic handling functions to perform
message distribution.
Possible SI values are:
3 = SCCP
4 = Telephone User Part (TUP)
5 = ISDN User Part (ISUP)
6 = Data User Part, call and circuit related messages
7 = Data User Part, facility registration and cancellation messages
8 = MTP Testing User Part
9 = Broadband ISDN User Part
10 = Satellite ISDN User Part
11 = Spare
12 = Q.2630.1
13 = Spare
14 = GCP (H.248)
15 = Spare
The service indicator must be unique among all Mtp3bAp instances,
referring to the same Mtp3bSrs. A maximum of 3 different service indicators
can be configured per Mtp3bSp.

Mtp3bAp

userLabel

RNC

Label for free use.

string

Mtp3bSlAnsi

autoStartLink

RNC

Specifies if the link should be activated at creation.

boolean

Mtp3bSlAnsi

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: the linkState is not Available. The link is
not aligned and it is not ready for the signalling link test procedure.
- FAILED: The MO has other reasons for staying DISABLED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

1 TRUE(1)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSlAnsi

linkState

RNC

Network Parameters

The link state.

126 (520)

long

The link state represents a bitmap which contains a combination of


the following hexadecimal values, long within parenthesis:
0x00 (0) Available
0x01 (1) Failed
0x02 (2) Remotely blocked
0x04 (4) Locally blocked
0x08 (8) Remotely inhibited
0x10 (16) Locally inhibited
0x20 (32) Deactivated
0x21 (33) Failed and deactivated

Mtp3bSlAnsi

Mtp3bSlAnsiId

RNC

The value component of the RDN.

string

Mtp3bSlAnsi

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

NOT_INITIALIZED = 0
INITIALIZED = 1

The operational state is ENABLED, if the link is aligned and can


handle traffic.
Mtp3bSlAnsi

proceduralState

RNC

The procedural state of the link.

Mtp3bProceduralState

Mtp3bSlAnsi

signLinkCode

RNC

The signalling link code, SLC, used for this link.


The signLinkCode for a link must be unique between the nodes,
independent on in which linkSet the link belongs.

long

Mtp3bSlAnsi

tpId

RNC

Reference to a termination point of the lower layer protocol.

ManagedObject

0..15

The possible MOs are:


Mtp2TpAnsi for narrowband.
NniSaalTp for broadband.
Only one link instance can reserve one termination point instance.
Only broadband is allowed on the HD stack.

Mtp3bSlAnsi

usageState

RNC

The usage state of the link.

Mtp3bUsageState

Mtp3bSlAnsi

userLabel

RNC

Label for free use.

string

Mtp3bSlChina

autoStartLink

RNC

Specifies if the link should be activated at creation.

boolean

Mtp3bSlChina

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: the linkState is not Available. The link is
not aligned and it is not ready for the signalling link test procedure.
- FAILED: The MO has other reasons for staying DISABLED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IDLE = 0
ACTIVE = 1
BUSY = 2

1 TRUE(1)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSlChina

linkState

RNC

Network Parameters

The link state.

127 (520)

long

The link state represents a bitmap which contains a combination of


the following hexadecimal values, long within parenthesis:
0x00 (0) Available
0x01 (1) Failed
0x02 (2) Remotely blocked
0x04 (4) Locally blocked
0x08 (8) Remotely inhibited
0x10 (16) Locally inhibited
0x20 (32) Deactivated
0x21 (33) Failed and deactivated

Mtp3bSlChina

Mtp3bSlChinaId

RNC

The value component of the RDN.

string

Mtp3bSlChina

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the link is aligned and can


handle traffic.
Mtp3bSlChina

prioBeforeSio

RNC

Specifies if the message priority shall be inserted in an octet before the


Service Indicator Octet (SIO).

boolean

Mtp3bSlChina

proceduralState

RNC

The procedural status of the link.

Mtp3bProceduralState

Mtp3bSlChina

signLinkCode

RNC

The signalling link code, SLC, used for this link.

long

0 FALSE(0)

NOT_INITIALIZED = 0
INITIALIZED = 1
0..15

The signLinkCode for a link must be unique between the nodes,


independent of which link set the link belongs to.
Mtp3bSlChina

tpId

RNC

Reference to a termination point of the lower layer protocol.

ManagedObject

The possible MOs are:


Mtp2TpChina for narrowband.
Mtp2HslTpChina for high speed link.
NniSaalTp for broadband.
Only one link instance can reserve one termination point instance.
Only broadband is allowed on the HD stack.

Mtp3bSlChina

usageState

RNC

The usage state of the link.

Mtp3bUsageState

Mtp3bSlChina

userLabel

RNC

Label for free use.

string

Mtp3bSlItu

autoStartLink

RNC

Specifies if the link should be activated at creation.

boolean

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IDLE = 0
ACTIVE = 1
BUSY = 2

1 TRUE(1)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSlItu

availabilityStatus

RNC

Network Parameters

The availability status.

128 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: the linkState is not Available. The link is
not aligned and it is not ready for the signalling link test procedure.
- FAILED: The MO has other reasons for staying DISABLED.

Mtp3bSlItu

linkState

RNC

The link state.

long

The link state represents a bitmap which contains a combination of


the following hexadecimal values, long within parenthesis:
0x00 (0) Available
0x01 (1) Failed
0x02 (2) Remotely blocked
0x04 (4) Locally blocked
0x08 (8) Remotely inhibited
0x10 (16) Locally inhibited
0x20 (32) Deactivated
0x21 (33) Failed and deactivated

Mtp3bSlItu

Mtp3bSlItuId

RNC

The value component of the RDN.

string

Mtp3bSlItu

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the link is aligned and can


handle traffic.
Mtp3bSlItu

prioBeforeSio

RNC

Specifies if the message priority shall be inserted in an octet before the


Service Indicator Octet (SIO).

boolean

Mtp3bSlItu

proceduralState

RNC

The procedural state of the link.

Mtp3bProceduralState

Mtp3bSlItu

signLinkCode

RNC

The signalling link code, SLC, used for this link.

long

0 FALSE(0)

NOT_INITIALIZED = 0
INITIALIZED = 1
0..15

The signLinkCode for a link must be unique between the nodes,


independent of which link set the link belongs to.
Mtp3bSlItu

tpId

RNC

Reference to a termination point of the lower layer protocol.

ManagedObject

The possible MOs are:


Mtp2TpItu for narrowband.
Mtp2HslTpItu for high speed link.
NniSaalTp for broadband.
Only one link instance can reserve one termination point instance.
Only broadband is allowed on the HD stack.

Mtp3bSlItu

Prepared: EZIEAGA

usageState

RNC

The usage state of the link.

Mtp3bUsageState

Date: 2014-05-27
Sheet: 14.0.2

IDLE = 0
ACTIVE = 1
BUSY = 2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Mtp3bSlItu

userLabel

RNC

Label for free use.

string

Mtp3bSls

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
- DEGRADED: at least one link in the link set has usage state IDLE
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: based on the operational state and
usage state of the related MOs Mtp3bSlAnsi, Mtp3bSlChina, Mtp3bSlItu, or
Mtp3bSlTtc.

Mtp3bSls

cLinkAnsi

RNC

The cLinkAnsi shall be set to true for a link set with C-links between STPpairs, to prevent SLS bit rotation in an ANSI network.

129 (520)

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

boolean

This attribute is only valid for an ANSI network.


Mtp3bSls

Mtp3bSlsId

RNC

The value component of the RDN.

string

Mtp3bSls

mtp3bSrsId

RNC

Reference to an instance of Mtp3bSrs.

Mtp3bSrs

Mtp3bSls

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if at least one link in the link set
is ENABLED.
Mtp3bSls

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

Mtp3bSr

Mtp3bSls

usageState

RNC

The usage state of the link set.

Mtp3bUsageState

- ACTIVE: At least one of the contained links of the SLS is ACTIVE


and no link is BUSY.
- BUSY: At least one of the contained links is BUSY.
- IDLE: All links of the SLS are IDLE.
Mtp3bSls

userLabel

RNC

Label for free use.

string

Mtp3bSlTtc

autoStartLink

RNC

Specifies if the link should be activated at creation.

boolean

Mtp3bSlTtc

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: the linkState is not Available. The link is
not aligned and it is not ready for the signalling link test procedure.
- FAILED: The MO has other reasons for staying DISABLED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IDLE = 0
ACTIVE = 1
BUSY = 2

1 TRUE(1)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSlTtc

linkState

RNC

Network Parameters

The link state.

130 (520)

long

The link state represents a bitmap which contains a combination of


the following hexadecimal values, long within parenthesis:
0x00 (0) Available
0x01 (1) Failed
0x02 (2) Remotely blocked
0x04 (4) Locally blocked
0x08 (8) Remotely inhibited
0x10 (16) Locally inhibited
0x20 (32) Deactivated
0x21 (33) Failed and deactivated

Mtp3bSlTtc

Mtp3bSlTtcId

RNC

The value component of the RDN.

string

Mtp3bSlTtc

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the link is aligned and can


handle traffic.
Mtp3bSlTtc

prioBeforeSio

RNC

Specifies if the message priority shall be inserted in an octet before the


Service Indicator Octet (SIO).

boolean

Mtp3bSlTtc

proceduralState

RNC

The procedural state of the link.

Mtp3bProceduralState

Mtp3bSlTtc

signLinkCode

RNC

The TTC three bit signalling link code (SLC) and TTC one bit A/Bindicator, long
used for this link.

1 TRUE(1)

NOT_INITIALIZED = 0
INITIALIZED = 1
0..15

The code have to be unique in this signal link set, i.e the
signallingLinkCode for all the Mtp3bSl that belongs to the same Mtp3bSls
must be unique (mutual exclusive).
Note that the LSB is treated as A/B indicator (according to TTC
standard), for example values 0,2,4 ... indicate A/B indicator set to 0
(equals A), and values 1,3,5 ... indicate A/B indicator set to 1 (equals B).

Mtp3bSlTtc

tpId

RNC

Reference to a termination point of the lower layer protocol.

ManagedObject

The possible MOs are:


Mtp2TpTtc for narrowband.
NniSaalTp for broadband.
Only one link instance can reserve one termination point instance.
Only broadband is allowed on the HD stack.

Mtp3bSlTtc

usageState

RNC

The usage state of the link.

Mtp3bUsageState

Mtp3bSlTtc

userLabel

RNC

Label for free use.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IDLE = 0
ACTIVE = 1
BUSY = 2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

availabilityStatus

RNC

Network Parameters

The availability status.

131 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- FAILED: the SP is not handled by any MTP3 instance.

Mtp3bSpAnsi

m3uaNoOfAttempsOfDauds

RNC

The number of attempts to send the Destination Audit (DAUD) message.

long

0..65535

long

0..5000

2000

2000

long

0..5000

2000

2000

If set to 0, the DAUD message is sent continuously until a


Destination Available (DAVA) message is received.
Applicable only for an E-SIGTRAN configuration.

Mtp3bSpAnsi

maxSizeChangeBuf

RNC

The maximum size of the changeover buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpAnsi

maxSizeReroutBuf

RNC

The maximum size of the rerouting buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpAnsi

modifiedSlsRotation

RNC

Specifies the standard behavior of Signalling Link Selection (SLS) rotation. ModifiedSlsRotation

DEACTIVATED = 0
ACTIVATED = 1

ACTIVATED(1)

ACTIVATED(1)

If this attribute is set to ACTIVATED, if two Mtp3bSr MOs with equal


priority are configured under an Mtb3bSrs MO, and if the attribute
nodeBehaviour is set to SEP (Signalling End Point) then the ?modified SLS
rotation? algorithm is used.
In all other cases, the ?original ANSI standard version? algorithm is
used.
If the attribute nodeBehaviour is changed from SEP to
SGW_STP_SEP or SEP_STP, the value is automatically changed to
DEACTIVATED.
Applicable only for SS7 configurations.

Mtp3bSpAnsi

Prepared: EZIEAGA

Mtp3bSpAnsiId

RNC

The value component of the RDN.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

networkInd

RNC

Network Parameters

The network indicator (NI) discriminates messages between different


networks.

132 (520)

Mtp3bNetworkInd

INTERNATIONAL_NETWORK = 0
SPARE = 1
NATIONAL_NETWORK = 2
RESERVED_FOR_NATIONAL_USE
=3

NodeBehaviourType

SEP = 0
SEP_STP = 4
SGW_STP_SEP = 5

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlAnsi instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

Mtp3bSpAnsi

nodeBehaviour

RNC

The type of MTP3 signalling point.


When setting this attribute, the following preconditions must be
fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- All related Mtp3bSlAnsi instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

NATIONAL_NETWORK(2)

SEP(0)

SEP(0)

IETF M3UA specific:


If set to SEP, and this signalling point is used by SGP, the signalling
gateway can serve only shared point code. That is, if this attribute is equal
to SEP and this Mtp3bSp is referenced by M3uaRemoteAs, then all
M3uaRkGrouping MOs related to that remote AS have to be configured
with the attribute dpc equal to the attribute signallingPointCode in this
Mtp3bSp.
Can be set only to SEP on the HD stack.

Mtp3bSpAnsi

noOfAttempsOfAssociationEstablishment

RNC

The maximum number of attempts to establish an M3UA association.

long

0..65535

Applicable only for an E-SIGTRAN configuration.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

noOfCongestLevelForNI

RNC

Network Parameters

The number of congestion levels for a national NI.

long

133 (520)
1..3

0..255

0..1

If set to 1, only congestion level 1 is handled.


This attribute is not applicable for an international NI.
Applicable only for SS7 configurations.
Mtp3bSpAnsi

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the SP is handled by at least


one MTP3 instance.
Mtp3bSpAnsi

resendTfcInterval

RNC

The resend TFC and SCON interval.

long

The number of messages received from the peer side, before the
Transfer Controlled (TFC) message or Signalling Congestion (SCON)
message is sent to the originating signalling point, indicating that the
destination is congested.
If set to 0, sending of TFC and SCON messages is suppressed.
Applicable only for SS7 and E-SIGTRAN configurations.

Mtp3bSpAnsi

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance. Can be of


type SccpSp.

ManagedObject

Mtp3bSpAnsi

routeSetCongestTestFlag

RNC

Specifies the congestion handling procedure to be used for national


networks, which have congestion priorities.

long

If set to 0, the congestion handling procedure described by the TTC


standard is applied. In this case the attribute timerTc is used.
If set to 1, the congestion handling procedure described by the
ANSI, ITU and China standards is applied. In this case the Route Set
Congestion Test function is used.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

rpuId

RNC

Network Parameters

Reference to an instance of ReliableProgramUniter MO (RPU).

134 (520)

ReliableProgramUniter

Specifies the SS7 stack for the MO.


If set to a ReliableProgramUniter MO, the SP belongs to the Mono
stack.
If set to NULL (no value), the SP belongs to the HD stack. IETF
M3UA signalling points cannot have this attribute set to NULL.
Only signalling points of the same standard can have the attribute
set to the same value.
A maximum of 15 instances of this MO can have the attribute set to
the same value.
The only value this attribute can be changed to during a set
operation is NULL. During the set, the Mono stack is converted to the HD
stack.

Mtp3bSpAnsi

signallingPointCode

RNC

When setting this attribute, the following preconditions must be


fulfilled:
- There is only one Mtp3bSpAnsi MO on the node.
- There are no Mtp3bSpChina, Mtp3bSpItu or Mtp3bSpTtc MOs on
the node.
- There are no SgwMgmtMapping MOs on the node.
- The attribute nodeBehaviour is set to SEP.
- The attribute useSgwMgmtMapping is set to False.
- If the Mtp3bSpAnsi MO has children Mtp3bSlAnsi MOs, they have
a reference only to NniSaalTp MO in the tpId attribute.
- The total number of SCCP connections, configured in the
maxConn attribute in the related SccpApLocal MOs, is less or equal to
32768.
Disturbances: At a change of this attribute the Mono stack will shut
down and the HD stack will start, this will cause disturbances to all MTP3
and SCCP traffic and all SCCP connections will be lost.
The Signalling Point Code (SPC) .
long

0..16777215

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlAnsi instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.
- In an IPSP configuration, there must be no related
M3uaRkGrouping instances for any of the related M3uaLocalAs instances.

Mtp3bSpAnsi

sioSpare

RNC

Specifies how the two spare bits in the Service Information Octet (SIO) are Mtp3bSioSpareBitsUse
used.

SPARE = 0
PRIO = 1

PRIO(1)

PRIO(1)

Applicable only for SS7 and E-SIGTRAN configurations.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

spPriority

RNC

Network Parameters

The priority data for this signalling point.

135 (520)

Mtp3bSpAnsiPriorityData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpAnsi

spPriority.prioCb

RNC

Specifies the priority for the Changeback-declaration (CBD) and


Changeback-acknowledgement (CBA) messages.

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.
Mtp3bSpAnsi

spPriority.prioCo

RNC

Specifies the priority for the Changeover-order (COO) and Changeoveracknowledgement (COA) or Extended Changeover Order (XCO) and
Extended Changeover Acknowledgement (XCA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioEc

RNC

Specifies the priority for the Emergency-changeover-order (ECO) and


Emergency-changeover-acknowledgement (ECA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioLink

RNC

Specifies the priority for link-related messages. The messages are:


Link inhibit (LIN)
Link uninhibit (LUN)
Link inhibit denied (LID)
Link inhibit acknowledgement (LIA)
Link uninhibit acknowledgement (LUA)
Link forced uninhibit (LFU)
Link local inhibit test (LLT)
Link remote inhibit test (LRT)
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioRst

RNC

Specifies the priority for Signalling-route-set-test signal for prohibited


destination (RST) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioSlt

RNC

Specifies the priority for Signalling Link Test Message (SLTM) and
Signalling Link Test Acknowledgement (SLTA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioTfc

RNC

Specifies the priority for the Transfer-controlled (TFC), Transfer-allowed


(TFA), Transfer-prohibited (TFP) and Transfer-restricted (TFR) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpAnsi

spPriority.prioTra

RNC

Specifies the priority for the Traffic-restart-allowed (TRA) message.


When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

spPriority.prioUpu

RNC

Network Parameters

Specifies the priority for the User part unavailable (UPU) message.

136 (520)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.
Mtp3bSpAnsi

spTimer

RNC

The timer data for this signaling point.

HIGHEST(3)

HIGHEST(3)

Mtp3bSpAnsiTimerData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpAnsi

spTimer.timerM3uaPeriodicAudit

RNC

Timer used for audit procedure, applicable for IPSEP and SGW. This is the long
time to wait before sending or resending the DAUD messages toward the
SGW to audit the state of SS7 destinations.

1..65535

300

300

Mtp3bSpAnsi

spTimer.timerM3uaT40

RNC

Delay to avoid message mis-sequencing in the following cases:


-when controlled or forced rerouting is initiated
-when an association fails and the association becomes active
Unit: 1 decisecond (1/10 second).

long

1..65535

Mtp3bSpAnsi

spTimer.timerM3uaT42

RNC

Timer for the interval between attempts to establish an association after


initial attempts were unsuccessful.

long

1..65535

Mtp3bSpAnsi

spTimer.timerM3uaTack

RNC

Maximum time to wait for message acknowledgement.

long

1..65535

40

40

long

1..65535

40

40

long

1..65535

50

50

long

1..65535

100

100

long

1..65535

400

400

long

1..65535

10

10

long

1..65535

400

400

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

This attribute must follow the rule:


timerM3uaTack > associationMaxRtx * maximumRto. The latter
attributes are in the Sctp MO.
Unit: 1 decisecond (1/10 second).
Mtp3bSpAnsi

spTimer.timerM3uaTassocack

RNC

Maximum time to wait for association establisment acknowledgement.


This attribute must follow the rule:
timerM3uaTassocack > (maxInitialRtrAtt + 1) * maximumRto. The
latter attributes are in the Sctp MO.
It should be longer than the time a message spends to reach the
most distant destination, be processed and returned.
Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerM3uaTc

RNC

Timer controlling the period a route set is considered congested when an


SCON message has been received.

Mtp3bSpAnsi

spTimer.timerSlta

RNC

Supervision timer for SLTA message.

Unit: 1 decisecond (1/10 second).

Corresponds to timer T1 in the ITU-T Q.707 standard.


Unit: 1 decisecond (1/10 second).
Mtp3bSpAnsi

spTimer.timerSltm

RNC

Timer for sending SLTM periodically.


Corresponds to timer T2 in the ITU-T Q.707 standard.
Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT1

RNC

Delay to avoid message mis-sequencing on changeover.


Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT10

RNC

Timer for sending RST periodically.


Unit: 1 decisecond (1/10 second).

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

spTimer.timerT12

RNC

Network Parameters

Supervision timer for Link uninhibit acknowledgement.

137 (520)

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

30

30

long

1..65535

20

20

long

1..65535

14

14

long

1..65535

long

1..65535

10

10

long

1..65535

1000

1000

long

1..65535

1000

1000

long

1..65535

600

600

long

1..65535

40

40

long

1..65535

300

300

long

1..65535

120

120

long

1..65535

20

20

long

1..65535

30

30

Unit: 1 decisecond (1/10 second).


Mtp3bSpAnsi

spTimer.timerT13

RNC

Supervision timer for Link forced uninhibit.

Mtp3bSpAnsi

spTimer.timerT14

RNC

Supervision timer for Link inhibit acknowledgement.

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).


Mtp3bSpAnsi

spTimer.timerT15

RNC

Supervision timer for start signaling route set congestiontest. Used only if
the "Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 20 - 30.
Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT16

RNC

Timer waiting for route set congestion status update. Used only if the
"Route Set Congestion Test Selecton" option is set to "Use Route Set
Congestion test".
Guiding value 14 - 22.
Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT17

RNC

Delay to avoid oscillation of initial alignment failure and link restart.


The value for this timer should be less than the value for timerT2.
Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT2

RNC

Timer for waiting for a COA.


Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT20

RNC

Timer controlling the periodic resending of a Local Inhibit Test message.


Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT21

RNC

Timer controlling the periodic resend of Remote Inhibit Test Message.

Mtp3bSpAnsi

spTimer.timerT22

RNC

Delay on commencement of MTP Restart to allow the node to rebuild an


accurate routing table based on messages for adjacent nodes.

Mtp3bSpAnsi

spTimer.timerT23

RNC

Supervision timer for routing updates on MTP Restart.

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).


Mtp3bSpAnsi

spTimer.timerT25

RNC

Supervision timer for reciept of a Traffic Restart Waiting message from an


adjacent SP which is restarting.

Mtp3bSpAnsi

spTimer.timerT26

RNC

Timer controlling the periodic resend of Traffic Restart Waiting messages


during restart of the local node.

Mtp3bSpAnsi

spTimer.timerT27

RNC

The minimum time period thats the links are out of service during MTP
restart.

Mtp3bSpAnsi

spTimer.timerT28

RNC

Timer controlling the time to react on a restart of an adjacent node.

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

spTimer.timerT29

RNC

Network Parameters

Timer for waiting for a Traffic Restart message from an adjacent node.

138 (520)

long

1..65535

600

600

long

1..65535

10

10

long

1..65535

300

300

long

1..65535

100

100

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

long

1..65535

long

1..65535

10

10

Unit: 1 decisecond (1/10 second).


Mtp3bSpAnsi

spTimer.timerT3

RNC

Delay to avoid message mis-sequencing on a time controlled diversion


change back.

Mtp3bSpAnsi

spTimer.timerT30

RNC

Timer for not sending TFPs and TFRs messages in response to


unexpected TRA and TRW.

Unit: 1 decisecond (1/10 second).

The timer is not valid if nodeBehaviour is set to SEP.


Unit: 1 decisecond (1/10 second).
Mtp3bSpAnsi

spTimer.timerT31

RNC

Timer controlling the time for the detection of false link congestion.

Mtp3bSpAnsi

spTimer.timerT4

RNC

Timer for waiting for CBA, first attempt.

Mtp3bSpAnsi

spTimer.timerT5

RNC

Timer for waiting for CBA, second attempt

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).


Mtp3bSpAnsi

spTimer.timerT6

RNC

Timer for delay to avoid message mis-sequencing on controlled rerouting.


Unit: 1 decisecond (1/10 second).

Mtp3bSpAnsi

spTimer.timerT8

RNC

Timer for delay to prohibit sending of TFP messages via the response
method. This is a STP specific parameter, which is ignored when
configured as an endpoint.

Mtp3bSpAnsi

spTimer.timerTBsnt

RNC

Waiting for BSNT value from MTP2 or NNI-SAAL at changeover (not


standard timer).

Mtp3bSpAnsi

spTimer.timerTc

RNC

Timer controlling the period a route set is considered congested when a


Transfer Controlled message has been received.

long

1..65535

50

50

Mtp3bSpAnsi

spTimer.timerTRetrieval

RNC

Timer for waiting for completion of buffer retrieval from MTP2 or NNI-SAAL long
at changeover (not standard timer).

1..65535

10

10

Mtp3bSpAnsi

spTimer.timerTStart

RNC

Timer for the interval between attempts to start a link. Timing starts when
timerT17 expires (not standard timer).

long

1..65535

1200

1200

Mtp3bSpAnsi

statusIndInterval

RNC

The status indication interval.

long

0..255

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

The number of messages received from the user part, before the
user part is notified that the destination is congested.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpAnsi

testPatternSltm

RNC

Specifies the test pattern in the Signalling Link Test Message (SLTM).
Allowed characters are 0-9, A-F. The pattern must contain an even
number of characters.

string

A5A5A5A5A5A5A A5A5A5A5A5A5A5A5A5A5
5A5A5A5A5A5A5 A5A5A5A5A5
A5A5

Applicable only for SS7 and E-SIGTRAN configurations.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpAnsi

transFrHandler

RNC

Specifies how a Transfer Restricted (TFR) message shall be treated.

Network Parameters

139 (520)

Mtp3bTfrHandling

IGNORED = 0
HANDLE_AS_TFA = 1
HANDLE_BY_STANDARD = 2

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpAnsi

userLabel

RNC

Label for free use.

string

Mtp3bSpAnsi

useSgwMgmtMapping

RNC

Specifies whether Associated Signalling Mode in SGW function (ASM) is


activated for this signalling point.

boolean

IGNORED(0)

IGNORED(0)

0 FALSE(0)

The ASM is configured using SgwMgmtMapping MOs.


Applicable only for SS7 and E-SIGTRAN configurations.
In an IETF M3UA configuration, this attribute is not applicable and
must be set to false.
If the HD stack is used, this attribute can be set only to False.

Mtp3bSpChina

availabilityStatus

RNC

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- FAILED: the SP is not handled by any MTP3 instance.

Mtp3bSpChina

m3uaNoOfAttempsOfDauds

RNC

The number of attempts to send the Destination Audit (DAUD) message.

long

0..65535

long

0..5000

2000

2000

long

0..5000

2000

2000

If set to 0, the DAUD message is sent continuously until a


Destination Available (DAVA) message is received.
Applicable only for an E-SIGTRAN configuration.

Mtp3bSpChina

maxSizeChangeBuf

RNC

The maximum size of the changeover buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpChina

maxSizeReroutBuf

RNC

The maximum size of the rerouting buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpChina

Prepared: EZIEAGA

Mtp3bSpChinaId

RNC

The value component of the RDN.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

networkInd

RNC

Network Parameters

The network indicator (NI) discriminates messages between different


networks.

140 (520)

Mtp3bNetworkInd

INTERNATIONAL_NETWORK = 0
SPARE = 1
NATIONAL_NETWORK = 2
RESERVED_FOR_NATIONAL_USE
=3

NodeBehaviourType

SEP = 0
SEP_STP = 4
SGW_STP_SEP = 5

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlChina instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

Mtp3bSpChina

nodeBehaviour

RNC

The type of MTP3 signalling point.


When setting this attribute, the following preconditions must be
fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- All related Mtp3bSlChina instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

NATIONAL_NETWORK(2)

SEP(0)

SEP(0)

IETF M3UA specific:


If set to SEP, and this signalling point is used by SGP, the signalling
gateway can serve only shared point code. That is, if this attribute is equal
to SEP and this Mtp3bSp is referenced by M3uaRemoteAs, then all
M3uaRkGrouping MOs related to that remote AS have to be configured
with the attribute dpc equal to the attribute signallingPointCode in this
Mtp3bSp.
Can be set only to SEP on the HD stack.

Mtp3bSpChina

noOfAttempsOfAssociationEstablishment

RNC

The maximum number of attempts to establish an M3UA association.

long

0..65535

Applicable only for an E-SIGTRAN configuration.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

noOfCongestLevelForNI

RNC

Network Parameters

The number of congestion levels for a national NI.

long

141 (520)
1..3

If set to 1, only congestion level 1 is handled.


This attribute is not applicable for an international NI.
Applicable only for SS7 configurations.
Mtp3bSpChina

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the SP is handled by at least


one MTP3 instance.
Mtp3bSpChina

resendTfcInterval

RNC

The resend TFC and SCON interval.

long

0..255

The number of messages received from the peer side, before the
Transfer Controlled (TFC) message or Signalling Congestion (SCON)
message is sent to the originating signalling point, indicating that the
destination is congested.
If set to 0, sending of TFC and SCON messages is suppressed.
Applicable only for SS7 and E-SIGTRAN configurations.

Mtp3bSpChina

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance. Can be of


type SccpSp.

ManagedObject

Mtp3bSpChina

restartType

RNC

This attribute shows what MTP3b restart standard the system follows. With RestartType
China, it is possible using this attribute to set which of the ITU restart
standard that shall be followed.

ITU_96_RESTART = 5
ITU_88_RESTART = 6

ITU_96_RESTART ITU_96_RESTART(5)
(5)

5 = ITU_96_RESTART
6 = ITU_88_RESTART
This attribute is applicable only when SS7 is the bearer.
Mtp3bSpChina

routeSetCongestTestFlag

RNC

Specifies the congestion handling procedure to be used for national


networks, which have congestion priorities.

long

0..1

If set to 0, the congestion handling procedure described by the TTC


standard is applied. In this case the attribute timerTc is used.
If set to 1, the congestion handling procedure described by the
ANSI, ITU and China standards is applied. In this case the Route Set
Congestion Test function is used.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

rpuId

RNC

Network Parameters

Reference to an instance of ReliableProgramUniter MO (RPU).

142 (520)

ReliableProgramUniter

Specifies the SS7 stack for the MO.


If set to a ReliableProgramUniter MO, the SP belongs to the Mono
stack.
If set to NULL (no value), the SP belongs to the HD stack. IETF
M3UA signalling points cannot have this attribute set to NULL.
Only signalling points of the same standard can have the attribute
set to the same value.
A maximum of 15 instances of this MO can have the attribute set to
the same value.
When setting this attribute, the following preconditions must be
fulfilled:
- There is only one Mtp3bSpChina MO on the node.
- There are no Mtp3bSpAnsi, Mtp3bSpItu or Mtp3bSpTtc MOs on
the node.
- There are no SgwMgmtMapping MOs on the node.
- The attribute nodeBehaviour is set to SEP.
- The attribute useSgwMgmtMapping is set to False.
- If the Mtp3bSpChina MO has children Mtp3bSlChina MOs, they
have a reference only to NniSaalTp MO in the tpId attribute.
- The total number of SCCP connections, configured in the
maxConn attribute in the related SccpApLocal MOs, is less or equal to
32768.

Mtp3bSpChina

signallingPointCode

RNC

The Signalling Point Code (SPC) .

long

0..16777215

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlChina instances must be stopped using the
action deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.
- In an IPSP configuration, there must be no related
M3uaRkGrouping instances for any of the related M3uaLocalAs instances.

Mtp3bSpChina

sioSpare

RNC

Specifies how the two spare bits in the Service Information Octet (SIO) are Mtp3bSioSpareBitsUse
used.

SPARE = 0
PRIO = 1

SPARE(0)

SPARE(0)

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpChina

spPriority

RNC

The priority data for this signalling point.

Mtp3bSpChinaPriorityData

Applicable only for SS7 and E-SIGTRAN configurations.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

spPriority.prioCb

RNC

Network Parameters

Specifies the priority for the Changeback-declaration (CBD) and


Changeback-acknowledgement (CBA) messages.

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.
Mtp3bSpChina

spPriority.prioCo

RNC

Specifies the priority for the Changeover-order (COO) and Changeoveracknowledgement (COA) or Extended Changeover Order (XCO) and
Extended Changeover Acknowledgement (XCA) messages.

143 (520)

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.
Mtp3bSpChina

spPriority.prioEc

RNC

Specifies the priority for the Emergency-changeover-order (ECO) and


Emergency-changeover-acknowledgement (ECA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioLink

RNC

Specifies the priority for link-related messages. The messages are:


Link inhibit (LIN)
Link uninhibit (LUN)
Link inhibit denied (LID)
Link inhibit acknowledgement (LIA)
Link uninhibit acknowledgement (LUA)
Link forced uninhibit (LFU)
Link local inhibit test (LLT)
Link remote inhibit test (LRT)
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioRst

RNC

Specifies the priority for Signalling-route-set-test signal for prohibited


destination (RST) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioSlt

RNC

Specifies the priority for Signalling Link Test Message (SLTM) and
Signalling Link Test Acknowledgement (SLTA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioTfc

RNC

Specifies the priority for the Transfer-controlled (TFC), Transfer-allowed


(TFA), Transfer-prohibited (TFP) and Transfer-restricted (TFR) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioTra

RNC

Specifies the priority for the Traffic-restart-allowed (TRA) message.


When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpChina

spPriority.prioUpu

RNC

Specifies the priority for the User part unavailable (UPU) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

spTimer

RNC

The timer data for this signaling point.

Network Parameters

144 (520)

Mtp3bSpChinaTimerData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpChina

spTimer.timerM3uaPeriodicAudit

RNC

Timer used for audit procedure, applicable for IPSEP and SGW. This is the long
time to wait before sending or resending the DAUD messages toward the
SGW to audit the state of SS7 destinations.

1..65535

300

300

Mtp3bSpChina

spTimer.timerM3uaT40

RNC

Delay to avoid message mis-sequencing in the following cases:


- when controlled or forced rerouting is initiated
- when an association fails and the association becomes active

long

1..65535

long

1..65535

long

1..65535

40

40

long

1..65535

40

40

long

1..65535

50

50

long

1..65535

100

100

long

1..65535

400

400

long

1..65535

10

10

long

1..65535

400

400

long

1..65535

10

10

long

1..65535

10

10

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerM3uaT42

RNC

Timer for the interval between attempts to establish an association after


initial attempts were unsuccessful.

Mtp3bSpChina

spTimer.timerM3uaTack

RNC

Maximum time to wait for message acknowledgement.

Unit: 1 decisecond (1/10 second)

This attribute must follow the rule:


timerM3uaTack > associationMaxRtx * maximumRto. The latter
attributes are in the Sctp MO.
Unit: 1 decisecond (1/10 second)
Mtp3bSpChina

spTimer.timerM3uaTassocack

RNC

Maximum time to wait for association establisment acknowledgement.


This attribute must follow the rule:
timerM3uaTassocack > (maxInitialRtrAtt + 1) * maximumRto. The
latter attributes are in the Sctp MO.
It should be longer than the time a message spends to reach the
most distant destination, be processed and returned.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerM3uaTc

RNC

Timer controlling the period a route set is considered congested when an


SCON message has been received.

Mtp3bSpChina

spTimer.timerSlta

RNC

Supervision timer for SLTA message.

Unit: 1 decisecond (1/10 second)

Corresponds to timer T1 in the ITU-T Q.707 standard.


Unit: 1 decisecond (1/10 second)
Mtp3bSpChina

spTimer.timerSltm

RNC

Timer for sending SLTM periodically.


Corresponds to timer T2 in the ITU-T Q.707 standard.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT1

RNC

Delay to avoid message mis-sequencing on changeover.

Mtp3bSpChina

spTimer.timerT10

RNC

Timer for sending RST periodically.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT12

RNC

Supervision timer for Link uninhibit acknowledgement.


Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT13

RNC

Supervision timer for Link forced uninhibit.


Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

spTimer.timerT14

RNC

Network Parameters

Supervision timer for Link inhibit acknowledgement.

145 (520)

long

1..65535

30

30

long

1..65535

20

20

long

1..65535

14

14

long

1..65535

long

1..65535

550

550

long

1..65535

680

680

long

1..65535

10

10

long

1..65535

600

600

long

1..65535

640

640

long

1..65535

2500

2500

long

1..65535

2500

2500

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

10

10

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT15

RNC

Supervision timer for start signaling route set congestiontest. Used only if
the "Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 20 - 30.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT16

RNC

Supervision timer for route set congestion status update. Used only if the
"Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 14 - 22.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT17

RNC

Delay to avoid oscillation of initial alignment failure and link restart.


The value for this timer should be less than the value for timerT2.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT18

RNC

Supervision timer for the first phase of a restarting STP. This is an STP
specific parameter, which is ignored when configured as an endpoint.
The value for this timer should be less than the value for timerT20.
Unit: 1 decisecond (1/10 second)

Mtp3bSpChina

spTimer.timerT19

RNC

Timer controlling the response of the receipt of a traffic restart message


from an adjacent node.

Mtp3bSpChina

spTimer.timerT2

RNC

Timer for waiting for a COA.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT20

RNC

Overall MTP restart timer at the restarting MTP.

Mtp3bSpChina

spTimer.timerT21

RNC

Overall MTP restart timer at an adjacent signalling point to a restarting


MTP.

Mtp3bSpChina

spTimer.timerT22

RNC

Timer for test of local inhibit.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT23

RNC

Remote inhibit test timer.

Mtp3bSpChina

spTimer.timerT3

RNC

Delay to avoid message mis-sequencing on a time controlled diversion


change back.

Mtp3bSpChina

spTimer.timerT4

RNC

Timer for waiting for CBA, first attempt.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT5

RNC

Timer for waiting for CBA, second attempt


Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpChina

spTimer.timerT6

RNC

Network Parameters

Timer for delay to avoid message mis-sequencing on controlled rerouting.

146 (520)

long

1..65535

long

1..65535

long

1..65535

10

10

Unit: 1 decisecond (1/10 second)


Mtp3bSpChina

spTimer.timerT8

RNC

Timer for delay to prohibit sending of TFP messages via the response
method. This is a STP specific parameter, which is ignored when
configured as an endpoint.

Mtp3bSpChina

spTimer.timerTBsnt

RNC

Waiting for BSNT value from MTP2 or NNI-SAAL at changeover (not


standard timer).

Mtp3bSpChina

spTimer.timerTc

RNC

Timer controlling the period a route set is considered congested when a


Transfer Controlled message has been received.

long

1..65535

50

50

Mtp3bSpChina

spTimer.timerTRetrieval

RNC

Timer for waiting for completion of buffer retrieval from MTP2 or NNI-SAAL long
at changeover (not standard timer).

1..65535

10

10

Mtp3bSpChina

spTimer.timerTStart

RNC

Timer for the interval between attempts to start a link. Timing starts when
timerT17 expires (not standard timer).

long

1..65535

1200

1200

Mtp3bSpChina

statusIndInterval

RNC

The status indication interval.

long

0..255

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

The number of messages received from the user part, before the
user part is notified that the destination is congested.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpChina

testPatternSltm

RNC

Specifies the test pattern in the Signalling Link Test Message (SLTM).

A5A5A5A5A5A5A A5A5A5A5A5A5A5A5A5A5
5A5A5A5A5A5A5 A5A5A5A5A5
A5A5

string

Allowed characters are 0-9, A-F. The pattern must contain an even
number of characters.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpChina

transFrHandler

RNC

Specifies how a Transfer Restricted (TFR) message shall be treated.

Mtp3bTfrHandling

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpChina

userLabel

RNC

Label for free use.

string

Mtp3bSpChina

useSgwMgmtMapping

RNC

Specifies whether Associated Signalling Mode in SGW function (ASM) is


activated for this signalling point.

boolean

IGNORED = 0
HANDLE_AS_TFA = 1
HANDLE_BY_STANDARD = 2

IGNORED(0)

IGNORED(0)

0 FALSE(0)

The ASM is configured using SgwMgmtMapping MOs.


Applicable only for SS7 and E-SIGTRAN configurations.
In an IETF M3UA configuration, this attribute is not applicable and
must be set to false.
If the HD stack is used, this attribute can be set only to False.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

availabilityStatus

RNC

Network Parameters

The availability status.

147 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- FAILED: the SP is not handled by any MTP3 instance.

Mtp3bSpItu

m3uaNoOfAttempsOfDauds

RNC

The number of attempts to send the Destination Audit (DAUD) message.

long

0..65535

long

0..5000

2000

2000

long

0..5000

2000

2000

If set to 0, the DAUD message is sent continuously until a


Destination Available (DAVA) message is received.
Applicable only for an E-SIGTRAN configuration.

Mtp3bSpItu

maxSizeChangeBuf

RNC

The maximum size of the changeover buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpItu

maxSizeReroutBuf

RNC

The maximum size of the rerouting buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpItu

Mtp3bSpItuId

RNC

The value component of the RDN.

string

Mtp3bSpItu

networkInd

RNC

The network indicator (NI) discriminates messages between different


networks.

Mtp3bNetworkInd

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlItu instances must be stopped using the action
deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

INTERNATIONAL_NETWORK = 0
SPARE = 1
NATIONAL_NETWORK = 2
RESERVED_FOR_NATIONAL_USE
=3

NATIONAL_NETWORK(2)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

nodeBehaviour

RNC

Network Parameters

The type of MTP3 signalling point.

148 (520)

NodeBehaviourType

SEP = 0
SEP_STP = 4
SGW_STP_SEP = 5

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- All related Mtp3bSlItu instances must be stopped using the action
deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

SEP(0)

SEP(0)

IETF M3UA specific:


If set to SEP, and this signalling point is used by SGP, the signalling
gateway can serve only shared point code. That is, if this attribute is equal
to SEP and this Mtp3bSp is referenced by M3uaRemoteAs, then all
M3uaRkGrouping MOs related to that remote AS have to be configured
with the attribute dpc equal to the attribute signallingPointCode in this
Mtp3bSp.
Can be set only to SEP on the HD stack.

Mtp3bSpItu

noOfAttempsOfAssociationEstablishment

RNC

The maximum number of attempts to establish an M3UA association.

long

0..65535

long

1..3

Applicable only for an E-SIGTRAN configuration.


Mtp3bSpItu

noOfCongestLevelForNI

RNC

The number of congestion levels for a national NI.


If set to 1, only congestion level 1 is handled.
This attribute is not applicable for an international NI.
Applicable only for SS7 configurations.

Mtp3bSpItu

operationalState

RNC

The operational state.

DISABLED = 0
ENABLED = 1

OperState

The operational state is ENABLED, if the SP is handled by at least


one MTP3 instance.
Mtp3bSpItu

resendTfcInterval

RNC

The resend TFC and SCON interval.

long

0..255

The number of messages received from the peer side, before the
Transfer Controlled (TFC) message or Signalling Congestion (SCON)
message is sent to the originating signalling point, indicating that the
destination is congested.
If set to 0, sending of TFC and SCON messages is suppressed.
Applicable only for SS7 and E-SIGTRAN configurations.

Mtp3bSpItu

Prepared: EZIEAGA

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance. Can be of


type SccpSp.

Date: 2014-05-27
Sheet: 14.0.2

ManagedObject

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

routeSetCongestTestFlag

RNC

Network Parameters

Specifies the congestion handling procedure to be used for national


networks, which have congestion priorities.

long

149 (520)
0..1

If set to 0, the congestion handling procedure described by the TTC


standard is applied. In this case the attribute timerTc is used.
If set to 1, the congestion handling procedure described by the
ANSI, ITU and China standards is applied. In this case the Route Set
Congestion Test function is used.

Mtp3bSpItu

rpuId

RNC

Reference to an instance of ReliableProgramUniter MO (RPU).

ReliableProgramUniter

Specifies the SS7 stack for the MO.


If set to a ReliableProgramUniter MO, the SP belongs to the Mono
stack.
If set to NULL (no value), the SP belongs to the HD stack. IETF
M3UA signalling points cannot have this attribute set to NULL.
Only signalling points of the same standard can have the attribute
set to the same value.
A maximum of 15 instances of this MO can have the attribute set to
the same value.
When setting this attribute, the following preconditions must be
fulfilled:
- There is only one Mtp3bSpItu MO on the node.
- There are no Mtp3bSpAnsi, Mtp3bSpChina or Mtp3bSpTtc MOs
on the node.
- There are no SgwMgmtMapping MOs on the node.
- The attribute nodeBehaviour is set to SEP.
- The attribute useSgwMgmtMapping is set to False.
- If the Mtp3bSpItu MO has children Mtp3bSlItu MOs, they have a
reference only to NniSaalTp MO in the tpId attribute.
- The total number of SCCP connections, configured in the
maxConn attribute in the related SccpApLocal MOs, is less or equal to
32768.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

signallingPointCode

RNC

Network Parameters

The Signalling Point Code (SPC) .

long

150 (520)
0..16383

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlItu instances must be stopped using action
deactivate or using action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.
- In an IPSP configuration, there must be no related
M3uaRkGrouping instances for any of the related M3uaLocalAs instances.

Mtp3bSpItu

sioSpare

RNC

Specifies how the two spare bits in the Service Information Octet (SIO) are Mtp3bSioSpareBitsUse
used.

SPARE = 0
PRIO = 1

PRIO(1)

PRIO(1)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpItu

spPriority

RNC

The priority data for this signalling point.

Mtp3bSpItuPriorityData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpItu

spPriority.prioCb

RNC

Specifies the priority for the Changeback-declaration (CBD) and


Changeback-acknowledgement (CBA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioCo

RNC

Specifies the priority for the Changeover-order (COO) and Changeoveracknowledgement (COA) or Extended Changeover Order (XCO) and
Extended Changeover Acknowledgement (XCA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioEc

RNC

Specifies the priority for the Emergency-changeover-order (ECO) and


Emergency-changeover-acknowledgement (ECA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

spPriority.prioLink

RNC

Network Parameters

Specifies the priority for link-related messages. The messages are:

151 (520)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Link inhibit (LIN)


Link uninhibit (LUN)
Link inhibit denied (LID)
Link inhibit acknowledgement (LIA)
Link uninhibit acknowledgement (LUA)
Link forced uninhibit (LFU)
Link local inhibit test (LLT)
Link remote inhibit test (LRT)
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioRst

RNC

Specifies the priority for Signalling-route-set-test signal for prohibited


destination (RST) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioSlt

RNC

Specifies the priority for Signalling Link Test Message (SLTM) and
Signalling Link Test Acknowledgement (SLTA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioTfc

RNC

Specifies the priority for the Transfer-controlled (TFC), Transfer-allowed


(TFA), Transfer-prohibited (TFP) and Transfer-restricted (TFR) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioTra

RNC

Specifies the priority for the Traffic-restart-allowed (TRA) message.


When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpItu

spPriority.prioUpu

RNC

Specifies the priority for the User part unavailable (UPU) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO

Mtp3bSpItu

spTimer

RNC

The timer data for this signaling point.

Mtp3bSpItuTimerData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpItu

spTimer.timerM3uaPeriodicAudit

RNC

Timer used for audit procedure, applicable for IPSEP and SGW. This is the long
time to wait before sending or resending the DAUD messages toward the
SGW to audit the state of SS7 destinations.

1..65535

300

300

Mtp3bSpItu

spTimer.timerM3uaT40

RNC

Delay to avoid message mis-sequencing in the following cases:


-when controlled or forced rerouting is initiated
-when an association fails and the association becomes active

long

1..65535

long

1..65535

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpItu

spTimer.timerM3uaT42

RNC

Timer for the interval between attempts to establish an association after


initial attempts were unsuccessful.
Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

spTimer.timerM3uaTack

RNC

Network Parameters

Maximum time to wait for message acknowledgement.

152 (520)

long

1..65535

40

40

long

1..65535

40

40

long

1..65535

50

50

long

1..65535

100

100

long

1..65535

400

400

long

1..65535

10

10

long

1..65535

400

400

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

30

30

long

1..65535

20

20

long

1..65535

14

14

This attribute must follow the rule:


timerM3uaTack > associationMaxRtx * maximumRto. The latter
attributes are in the Sctp MO.
Unit: 1 decisecond (1/10 second)
Mtp3bSpItu

spTimer.timerM3uaTassocack

RNC

Maximum time to wait for association establisment acknowledgement.


This attribute must follow the rule:
timerM3uaTassocack > (maxInitialRtrAtt + 1) * maximumRto. The
latter attributes are in the Sctp MO.
It should be longer than the time a message spends to reach the
most distant destination, be processed and returned.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerM3uaTc

RNC

Timer controlling the period a route set is considered congested when an


SCON message has been received.

Mtp3bSpItu

spTimer.timerSlta

RNC

Supervision timer for SLTA message.

Unit: 1 decisecond (1/10 second)

Corresponds to timer T1 in the ITU-T Q.707 standard.


Unit: 1 decisecond (1/10 second)
Mtp3bSpItu

spTimer.timerSltm

RNC

Timer for sending SLTM periodically.


Corresponds to timer T2 in the ITU-T Q.707 standard.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT1

RNC

Delay to avoid message mis-sequencing on changeover.


Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT10

RNC

Timer for sending RST periodically.


Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT12

RNC

Supervision timer for Link uninhibit acknowledgement.

Mtp3bSpItu

spTimer.timerT13

RNC

Supervision timer for Link forced uninhibit.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpItu

spTimer.timerT14

RNC

Supervision timer for Link inhibit acknowledgement.


Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT15

RNC

Supervision timer for start signaling route set congestiontest. Used only if
the "Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 20 - 30.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT16

RNC

Supervision timer for route set congestion status update. Used only if the
"Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 14 - 22.
Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

spTimer.timerT17

RNC

Network Parameters

Delay to avoid oscillation of initial alignment failure and link restart.

153 (520)

long

1..65535

long

1..65535

550

550

long

1..65535

680

680

long

1..65535

10

10

long

1..65535

600

600

long

1..65535

640

640

long

1..65535

2500

2500

long

1..65535

2500

2500

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

The value for this timer should be less than the value for timerT2.
Unit: 1 decisecond (1/10 second)
Mtp3bSpItu

spTimer.timerT18

RNC

Supervision timer for the first phase of a restarting STP. This is an STP
specific parameter, which is ignored when configured as an endpoint.
The value for this timer should be less than the value for timerT20.
If the attribute version is set to ITU_T_88 the recommended value
is 200.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT19

RNC

Timer controlling the response of the receipt of a traffic restart message


from an adjacent node.
If the attribute version is set to ITU_T_88, the recommended value
is 40.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT2

RNC

Timer for waiting for a COA.

Mtp3bSpItu

spTimer.timerT20

RNC

Overall MTP restart timer at the restarting MTP.

Unit: 1 decisecond (1/10 second)

If the attribute version is set to ITU_T_88, the recommended value


is 40.
Unit: 1 decisecond (1/10 second)
Mtp3bSpItu

spTimer.timerT21

RNC

Overall MTP restart timer at an adjacent signalling point to a restarting


MTP.
If the attribute version is set to ITU_T_88, the recommended value
is 300.
Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT22

RNC

Timer for test of local inhibit.


Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT23

RNC

Remote inhibit test timer.


Unit: 1 decisecond (1/10 second)

Mtp3bSpItu

spTimer.timerT3

RNC

Delay to avoid message mis-sequencing on a time controlled diversion


change back.

Mtp3bSpItu

spTimer.timerT4

RNC

Timer for waiting for CBA, first attempt.

Mtp3bSpItu

spTimer.timerT5

RNC

Timer for waiting for CBA, first attempt.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpItu

spTimer.timerT6

RNC

Timer for delay to avoid message mis-sequencing on controlled rerouting.


Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpItu

spTimer.timerT8

RNC

Timer for delay to prohibit sending of TFP messages via the response
method. This is a STP specific parameter, which is ignored when
configured as an endpoint.

Mtp3bSpItu

spTimer.timerTBsnt

RNC

Waiting for BSNT value from MTP2 or NNI-SAAL at changeover (not


standard timer).

Mtp3bSpItu

spTimer.timerTc

RNC

Timer controlling the period a route set is considered congested when a


Transfer Controlled message has been received.

Mtp3bSpItu

spTimer.timerTRetrieval

Mtp3bSpItu

Mtp3bSpItu

Network Parameters

154 (520)

long

1..65535

long

1..65535

10

10

long

1..65535

50

50

RNC

Timer for waiting for completion of buffer retrieval from MTP2 or NNI-SAAL long
at changeover (not standard timer).

1..65535

10

10

spTimer.timerTStart

RNC

Timer for the interval between attempts to start a link. Timing starts when
timerT17 expires (not standard timer).

long

1..65535

1200

1200

statusIndInterval

RNC

The status indication interval.

long

0..255

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

The number of messages received from the user part, before the
user part is notified that the destination is congested.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpItu

testPatternSltm

RNC

Specifies the test pattern in the Signalling Link Test Message (SLTM).

A5A5A5A5A5A5A A5A5A5A5A5A5A5A5A5A5
5A5A5A5A5A5A5 A5A5A5A5A5
A5A5

string

Allowed characters are 0-9, A-F. The pattern must contain an even
number of characters.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpItu

transFrHandler

RNC

Specifies how a Transfer Restricted (TFR) message shall be treated.

Mtp3bTfrHandling

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpItu

userLabel

RNC

Label for free use.

string

Mtp3bSpItu

useSgwMgmtMapping

RNC

Specifies whether Associated Signalling Mode in SGW function (ASM) is


activated for this signalling point.

boolean

IGNORED = 0
HANDLE_AS_TFA = 1
HANDLE_BY_STANDARD = 2

IGNORED(0)

IGNORED(0)

0 FALSE(0)

The ASM is configured using SgwMgmtMapping MOs.


Applicable only for SS7 and E-SIGTRAN configurations.
In an IETF M3UA configuration, this attribute is not applicable and
must be set to false.
If the HD stack is used, this attribute can be set only to False.

Mtp3bSpItu

version

RNC

Specifies the version of the MTP3 ITU-T standard.

Mtp3bVersion

Applicable only for an SS7 configuration.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

ITU_T_88 = 0
ITU_T_03_93 = 1
ITU_T_07_96 = 2

ITU_T_07_96(2)

ITU_T_07_96(2)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

availabilityStatus

RNC

The availability status.

Network Parameters

155 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- FAILED: the SP is not handled by any MTP3 instance.

Mtp3bSpTtc

m3uaNoOfAttempsOfDauds

RNC

The number of attempts to send the Destination Audit (DAUD) message.

long

0..65535

long

0..5000

2000

2000

long

0..5000

2000

2000

If set to 0, the DAUD message is sent continuously until a


Destination Available (DAVA) message is received.
Applicable only for an E-SIGTRAN configuration.

Mtp3bSpTtc

maxSizeChangeBuf

RNC

The maximum size of the changeover buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpTtc

maxSizeReroutBuf

RNC

The maximum size of the rerouting buffer.


Applicable only for SS7 and E-SIGTRAN configurations.
Unit: 1 KB

Mtp3bSpTtc

Prepared: EZIEAGA

Mtp3bSpTtcId

RNC

The value component of the RDN.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

nodeBehaviour

RNC

Network Parameters

The type of MTP3 signalling point.

156 (520)

NodeBehaviourType

SEP = 0
SEP_STP = 4
SGW_STP_SEP = 5

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- All related Mtp3bSlTtc instances must be stopped using the action
deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.

SEP(0)

SEP(0)

IETF M3UA specific:


If set to SEP, and this signalling point is used by SGP, the signalling
gateway can serve only shared point code. That is, if this attribute is equal
to SEP and this Mtp3bSp is referenced by M3uaRemoteAs, then all
M3uaRkGrouping MOs related to that remote AS have to be configured
with the attribute dpc equal to the attribute signallingPointCode in this
Mtp3bSp.
Can be set only to SEP on the HD stack.

Mtp3bSpTtc

noOfAttempsOfAssociationEstablishment

RNC

The maximum number of attempts to establish an M3UA association.

long

0..65535

long

1..3

Applicable only for an E-SIGTRAN configuration.


Mtp3bSpTtc

noOfCongestLevelForNI

RNC

The number of congestion levels for a national NI.


If set to 1, only congestion level 1 is handled.
This attribute is not applicable for an international NI.
Applicable only for SS7 configurations.

Mtp3bSpTtc

operationalState

RNC

The operational state.

DISABLED = 0
ENABLED = 1

OperState

The operational state is ENABLED, if the SP is handled by at least


one MTP3 instance.
Mtp3bSpTtc

resendTfcInterval

RNC

The resend TFC and SCON interval.

long

0..255

The number of messages received from the peer side, before the
Transfer Controlled (TFC) message or Signalling Congestion (SCON)
message is sent to the originating signalling point, indicating that the
destination is congested.
If set to 0, sending of TFC and SCON messages is suppressed.
Applicable only for SS7 and E-SIGTRAN configurations.

Mtp3bSpTtc

Prepared: EZIEAGA

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance. Can be of


type SccpSp.

Date: 2014-05-27
Sheet: 14.0.2

ManagedObject

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

routeSetCongestTestFlag

RNC

Network Parameters

Specifies the congestion handling procedure to be used for national


networks, which have congestion priorities.

long

157 (520)
0..1

If set to 0, the congestion handling procedure described by the TTC


standard is applied. In this case the attribute timerTc is used.
If set to 1, the congestion handling procedure described by the
ANSI, ITU and China standards is applied. In this case the Route Set
Congestion Test function is used.

Mtp3bSpTtc

rpuId

RNC

Reference to an instance of ReliableProgramUniter MO (RPU).

ReliableProgramUniter

Specifies the SS7 stack for the MO.


If set to a ReliableProgramUniter MO, the SP belongs to the Mono
stack.
If set to NULL (no value), the SP belongs to the HD stack. IETF
M3UA signalling points cannot have this attribute set to NULL.
Only signalling points of the same standard can have the attribute
set to the same value.
A maximum of 15 instances of this MO can have the attribute set to
the same value.
When setting this attribute, the following preconditions must be
fulfilled:
- There is only one Mtp3bSpTtc MO on the node.
- There are no Mtp3bSpAnsi, Mtp3bSpChina or Mtp3bSpItu MOs
on the node.
- There are no SgwMgmtMapping MOs on the node.
- The attribute nodeBehaviour is set to SEP.
- The attribute useSgwMgmtMapping is set to False.
- If the Mtp3bSpTtc MO has children Mtp3bSlTtc MOs, they have a
reference only to NniSaalTp MO in the tpId attribute.
- The total number of SCCP connections, configured in the
maxConn attribute in the related SccpApLocal MOs, is less or equal to
32768.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

signallingPointCode

RNC

Network Parameters

The Signalling Point Code (SPC) .

long

158 (520)
0..65535

When setting this attribute, the following preconditions must be


fulfilled:
- An SCCP user cannot reference any SccpApLocal MO related to
this Mtp3bSp MO instance.
- No external MTP3 user can have a reference to an Mtp3bAp
related to this MO.
- All related Mtp3bSlTtc instances must be stopped using the action
deactivate or the action deactivateLinkSet on the parent Mtp3bSls.
E-SIGTRAN specific:
- All related M3uAssociation instances must be stopped using the
action setAutoDown.
IETF M3UA specific:
- In an IPSP configuration, in case of double exchange mode, and
in an SGP configuration, all related M3uaRemoteSp instances must be
LOCKED.
- In an IPSP configuration, in case of single exchange mode, and in
an ASP configuration, either all related M3uaRemoteSp instances or the
related M3uaLocalAs instance must be LOCKED.
- In an IPSP configuration, there must be no related
M3uaRkGrouping instances for any of the related M3uaLocalAs instances.

Mtp3bSpTtc

spPriority

RNC

The priority data for this signalling point.

Mtp3bSpTtcPriorityData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpTtc

spPriority.prioCb

RNC

Specifies the priority for the Changeback-declaration (CBD) and


Changeback-acknowledgement (CBA) messages.

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

HIGHEST(3)

HIGHEST(3)

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.
Mtp3bSpTtc

spPriority.prioCo

RNC

Specifies the priority for the Changeover-order (COO) and Changeoveracknowledgement (COA) or Extended Changeover Order (XCO) and
Extended Changeover Acknowledgement (XCA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpTtc

spPriority.prioEc

RNC

Specifies the priority for the Emergency-changeover-order (ECO) and


Emergency-changeover-acknowledgement (ECA) messages.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpTtc

spPriority.prioRst

RNC

Specifies the priority for Signalling-route-set-test signal for prohibited


destination (RST) message.
When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpTtc

Prepared: EZIEAGA

spPriority.prioRt

RNC

Specifies the priority for signalling route test (SRT/SRA) messages.

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

spPriority.prioTfc

RNC

Network Parameters

Specifies the priority for the Transfer-controlled (TFC), Transfer-allowed


(TFA), Transfer-prohibited (TFP) and Transfer-restricted (TFR) messages.

159 (520)

Mtp3bSpPriorityLevel

LOWEST = 0
LOW = 1
HIGH = 2
HIGHEST = 3

When a message is sent from the MTP3, the message priority uses
the two spare bits in the SIO.

Mtp3bSpTtc

spTimer

RNC

The timer data for this signaling point.

HIGHEST(3)

HIGHEST(3)

Mtp3bSpTtcTimerData

Applicable only for SS7 and E-SIGTRAN configurations.


Mtp3bSpTtc

spTimer.timerSrt

RNC

Timer for waiting for Signalling Route Test Acknowledgement.

long

1..65535

100

100

long

1..65535

10

10

long

1..65535

400

400

long

1..65535

20

20

long

1..65535

14

14

long

1..65535

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

10

10

long

1..65535

long

1..65535

Unit: 1 decisecond (1/10 second)


Mtp3bSpTtc

spTimer.timerT1

RNC

Delay to avoid message mis-sequencing on changeover.

Mtp3bSpTtc

spTimer.timerT10

RNC

Timer for sending RST periodically.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpTtc

spTimer.timerT15

RNC

Supervision timer for start signaling route set congestiontest. Used only if
the "Route Set Congestion Test Selection" option is set to "Use Route Set
Congestion test".
Guiding value 20 - 30.
Unit: 1 decisecond (1/10 second)

Mtp3bSpTtc

spTimer.timerT16

RNC

Supervision timer for route set congestion status update. Used only if the
"Route Set Congestion Test Selecton" option is set to "Use Route Set
Congestion test".
Guiding value 14 - 22.
Unit: 1 decisecond (1/10 second)

Mtp3bSpTtc

spTimer.timerT17

RNC

Delay to avoid oscillation of initial alignment failure and link restart.


The value for this timer should be less than the value for timerT2.
Unit: 1 decisecond (1/10 second)

Mtp3bSpTtc

spTimer.timerT2

RNC

Timer for waiting for a COO or a COA.


Unit: 1 decisecond (1/10 second)

Mtp3bSpTtc

spTimer.timerT3

RNC

Delay to avoid message mis-sequencing on a time controlled diversion


change back.

Mtp3bSpTtc

spTimer.timerT4

RNC

Timer for waiting for CBA, first attempt.

Mtp3bSpTtc

spTimer.timerT6

RNC

Timer for delay to avoid message mis-sequencing on controlled rerouting.

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


Mtp3bSpTtc

spTimer.timerT8

RNC

Timer for delay to prohibit sending of TFP messages via the response
method. This is a STP specific parameter, which is ignored when
configured as an endpoint.
Unit: 1 decisecond (1/10 second)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

spTimer.timerTBsnt

RNC

Waiting for BSNT value from MTP2 or NNI-SAAL at changeover (not


standard timer).

Mtp3bSpTtc

spTimer.timerTc

RNC

Timer controlling the period a route set is considered congested when a


Transfer Controlled message has been received.

Mtp3bSpTtc

spTimer.timerTRetrieval

Mtp3bSpTtc

Mtp3bSpTtc

Network Parameters

160 (520)

long

1..65535

10

10

long

1..65535

50

50

RNC

Timer for waiting for completion of buffer retrieval from MTP2 or NNI-SAAL long
at changeover (not standard timer).

1..65535

10

10

spTimer.timerTStart

RNC

Timer for the interval between attempts to start a link. Timing starts when
timerT17 expires (not standard timer).

1..65535

1200

1200

spTimerM3ua

RNC

The M3UA timer data for this signaling point.

1..65535

300

300

long

1..65535

1..65535

long

1..65535

long

1..65535

long

1..65535

long

1..65535

long

1..65535

long

1..65535

40

40

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)

Unit: 1 decisecond (1/10 second)


long

Unit: 1 decisecond (1/10 second)


M3uaTimerData

Applicable only for an E-SIGTRAN configuration.


Mtp3bSpTtc

spTimerM3ua.timerM3uaPeriodicAudit

RNC

Timer used for audit procedure, applicable for IPSEP and SGW. This is the long
time to wait before sending or resending the DAUD messages toward the
SGW to audit the state of SS7 destinations.

Mtp3bSpTtc

spTimerM3ua.timerM3uaT1

RNC

Delay to avoid mis-sequencing of messages when an association fails.

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).


Mtp3bSpTtc

spTimerM3ua.timerM3uaT3

RNC

Delay to avoid mis-sequencing of messages when an association becomes long


active.

Mtp3bSpTtc

spTimerM3ua.timerM3uaT40

RNC

Delay to avoid message mis-sequencing when controlled or forced


rerouting is initiated.

Mtp3bSpTtc

spTimerM3ua.timerM3uaT41

RNC

Timer controlling the traffic activation delay during restart.

Mtp3bSpTtc

spTimerM3ua.timerM3uaT42

RNC

Timer for the interval between attempts to establish an association after


initial attempts were unsuccessful.

Mtp3bSpTtc

spTimerM3ua.timerM3uaT6

RNC

Delay to avoid mis-sequencing when controlled rerouting is initiated.

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).

Unit: 1 decisecond (1/10 second).


Mtp3bSpTtc

spTimerM3ua.timerM3uaT8

RNC

Delay to inhibit sending of DUNA messages using the response method.


Unit: 1 decisecond (1/10 second).

Mtp3bSpTtc

spTimerM3ua.timerM3uaTack

RNC

Maximum time to wait for message acknowledgement.


This attribute must follow the rule:
timerM3uaTack > associationMaxRtx * maximumRto. The latter
attributes are in the Sctp MO.
Unit: 1 decisecond (1/10 second).

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSpTtc

spTimerM3ua.timerM3uaTassocack

RNC

Network Parameters

Maximum time to wait for association establisment acknowledgement.

161 (520)

long

1..65535

40

40

long

1..65535

50

50

long

0..255

7711

7711

This attribute must follow the rule:


timerM3uaTassocack > (maxInitialRtrAtt + 1) * maximumRto. The
latter attributes are in the Sctp MO.
It should be longer than the time a message spends to reach the
most distant destination, be processed and returned.
Unit: 1 decisecond (1/10 second).
Mtp3bSpTtc

spTimerM3ua.timerM3uaTc

RNC

Timer controlling the period a route set is considered congested when an


SCON message has been received.

Mtp3bSpTtc

statusIndInterval

RNC

The status indication interval.

Unit: 1 decisecond (1/10 second).

The number of messages received from the user part, before the
user part is notified that the destination is congested.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpTtc

testPatternSltm

RNC

Specifies the test pattern in the Signalling Link Test Message (SLTM).

string

Allowed characters are 0-9, A-F. The pattern must contain an even
number of characters.
Applicable only for SS7 and E-SIGTRAN configurations.
Mtp3bSpTtc

userLabel

RNC

Label for free use.

string

Mtp3bSpTtc

useSgwMgmtMapping

RNC

Specifies whether Associated Signalling Mode in SGW function (ASM) is


activated for this signalling point.

boolean

0 FALSE(0)

The ASM is configured using SgwMgmtMapping MOs.


Applicable only for SS7 and E-SIGTRAN configurations.
In an IETF M3UA configuration, this attribute is not applicable and
must be set to false.
If the HD stack is used, this attribute can be set only to False.

Mtp3bSr

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- DEPENDENCY_FAILED: based on the operational state of the
related Mtp3bSrs, Mtp3bSls and M3uAssociation MOs.

Mtp3bSr

linkSetM3uId

RNC

Reference to an instance of Mtp3bSls or M3uAssociation.

ManagedObject

Mtp3bSr

Mtp3bSrId

RNC

The value component of the RDN.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSr

operationalState

RNC

Network Parameters

The operational state.

162 (520)

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the destination is available via


the link set or via M3UA association referenced in linkSetM3uId attribute.
Mtp3bSr

priority

RNC

The priority of the alternative route.

long

1..5

The traffic is directed to the highest priority route(s) available in the


route set. If more than one route has the same priority within a route set,
loadsharing is permitted between these routes.
The value 1 is the highest priority.
Mtp3bSr

routeBlockingState

RNC

The blocking state of the route.

RouteState

Mtp3bSr

usageState

RNC

The usage state of the route.

Mtp3bUsageState

NOT_BLOCKED = 0
BLOCKED = 1
IDLE = 0
ACTIVE = 1
BUSY = 2

For direct routes, the value of the attribute is the same as for
usageState in the related Mtp3bSls.

NOT_BLOCKED(0
)

For routes via STP or SGW, usageState is determined by traffic


management messages:
- ACTIVE: A TFA or a DAVA is received.
- BUSY: A TFC or an SCON is received.
- IDLE: A TFP or a DUNA is received.

Mtp3bSr

userLabel

RNC

Label for free use.

string

Mtp3bSrs

congestedLevel

RNC

In SS7 and E-SIGTRAN configurations, this attribute indicates whether the Mtp3bCongestLevel
Route Set is congested.
In an IETF M3UA configuration, it indicates whether the remote
destination is congested.

Mtp3bSrs

destPointCode

RNC

The destination point code (DPC).

long

NOT_CONGESTED = 0
CONGESTED = 1

0..16777215

The Destination Point Code in a Route Set has to be unique within


each Signaling Point.
The format of this attribute must be aligned with the standard of the
parent Mtp3bSp: ANSI, China, ITU or TTC.
In an IETF M3UA configuration, a DPC can be equal to the local
point code, if the DPC represents a destination reachable via the IP
network. This is a normal case for Associated Signalling Mode in SGW
function (ASM), where an SGW and ASP are configured with equal point
codes. Such a configuration is allowed only if the parent Mtp3bSp has SEP
node behavior, to avoid unexpected traffic losses. Such a route set cannot
be used for MTP3 traffic. That is, it cannot have routes and it cannot be
reserved by Mtp3bAp MOs.
In SS7 and E-SIGTRAN configurations, a route set must not have
DPC equal to the local point code.
The local point code is configured in the attribute
signallingPointcode and the node behavior is configured in the attribute
nodeBehaviour in the parent Mtp3bSp MO.

Mtp3bSrs

Prepared: EZIEAGA

Mtp3bSrsId

RNC

The value component of the RDN.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Mtp3bSrs

operationalState

RNC

Network Parameters

The operational state.

163 (520)

OperState

DISABLED = 0
ENABLED = 1

M3BearerType

SS7 = 1
IP = 2

The operational state is ENABLED, if the destination is available via


SS7 and/or IP.
Mtp3bSrs

preferredBearer

RNC

The preferred bearer type for routing outgoing messages.

SS7(1)

SS7(1)

The specified bearer is used if available. A rerouting between


bearers is performed automatically.
Only the SS7 value is applicable for SS7 and E-SIGTRAN
configurations.
Mtp3bSrs

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

Mtp3bSrs

userLabel

RNC

Label for free use.

string

MulticastListener

multicastInterfaceRef

RBS DUW

Reference to an IpInterface MO or an Ipv6Interface MO.

ManagedObject

Only one instance can be referenced by this attribute.


Deleting this MO with IP multicast groups active, will invalidate all related IP
multicast groups.
If the reference is to an IpInterface MO, at least one IpAccessHostEt MO
must also refer to the IpInterface MO.
If no IpAccessHostEt MO refers to the IpInterface MO, the multicast traffic
flow will be disabled.
MinimumLength: 1
MulticastListener

multicastInterfaceRef

RNC

Reference to a Ipv6Interface MO.

ManagedObject

Deleting this MO with IP multicast groups active, will invalidate all


related IP multicast groups.
MinimumLength: 1
MulticastListener
MulticastListener
MulticastListener
MulticastListener
NbapCommon

MulticastListenerId
MulticastListenerId
userLabel
userLabel
activeBearer

RBS DUW
RNC
RBS DUW
RNC
RBS DUW

The value component of the RDN.


The value component of the RDN.
Label for free use.
Label for free use.
Specifies which UniSaalTp is active when ATM is transport bearer alt. that
Sctp is active when IPv4 is bearer.

string
string
string
string
Nbap_ActiveBearer

NONE = 0
UNI_SAAL_TP_REF1 = 1
UNI_SAAL_TP_REF2 = 2
SCTP_REF = 3

Possible values:
NONE = No active bearer.
UNI_SAAL_TP_REF1 = Attribute uniSaalTpRef1 is used.
UNI_SAAL_TP_REF2 = Attribute uniSaalTpRef2 is used.
SCTP_REF = Attribute sctpRef is used.
NbapCommon

activeUniSaalTpRef

RNC

administrativeState

RNC

Reference to the UniSaalTp Managed Object that represents the active


UNI SAAL termination point.
The administrative state of the signaling link.

UniSaalTp

NbapCommon
NbapCommon

auditRetransmissionT

RBS DUW

Time between successive audit retransmissions.

long

LOCKED = 0
UNLOCKED = 1

SupportedAdminStates
1..150

LOCKED(0)
5

Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
NbapCommon

availabilityStatus

RBS DUW

The availability status of the protocol termination.

Network Parameters

164 (520)

AvailabilityStatus

IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
NO_STATUS = 0

Possible values:
NOT_INSTALLED
POWER_OFF
IN_TEST
DEPENDENCY_LOCKED
DEPENDENCY_FAILED
FAILED
OFF_LINE
DEGRADED
OFF_DUTY
LOG_FULL
NO STATUS = Full availability.
Specification: ITU-T rec. X.731
NbapCommon

availabilityStatus

RNC

The availability status of the NBAP common signaling bearer.


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9, bit 10 or bit 11 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED
Bit 11 = 1: DEPENDENCYSHUTTINGDOWN

long

0..4095

NbapCommon

l2EstablishReqRetryT

RBS DUW

Time between successive attempts to establish layer 2 communication.

long

1..150

long

1..600

30

30

long

1..600

30

30

Unit: 1 s
NbapCommon

l2EstablishSupervisionT

RBS DUW

NbapCommon

l3EstablishSupervisionT

RBS DUW

NbapCommon
NbapCommon
NbapCommon

NbapCommonId
NbapCommonId
operationalState

RBS DUW
RNC
RBS DUW

Maximum allowed time to establish layer 2 communication.


Unit: 1 s
Maximum allowed time to establish NBAP communication, that is,
successful establishment of layer 2 followed by a successful audit
procedure.
Unit: 1 s
The value component of the RDN.
Naming attribute. Contains the value part of the RDN.
Defines the operational state.

string
string
OperState

DISABLED = 0
ENABLED = 1

Possible values:
DISABLED
ENABLED
Specification: ITU-T rec. X.731
NbapCommon

operationalState

RNC

The operational state of the NBAP common signaling bearer.

NbapCommon

sctpRef

RBS DUW

NbapCommon

standbyUniSaalTpRef

RNC

Reference to the Sctp instance used. The reference is only used if the
Sctp
controlPlaneTransportOption is set to IPv4.
Reference to the UniSaalTp Managed Object that represents the stand-by UniSaalTp
UNI SAAL termination point.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

SupportedOperStates

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
NbapCommon

uniSaalTpRef1

RBS DUW

Network Parameters

165 (520)

Reference to the UniSaalTp instance used for the primary signalling bearer. UniSaalTp
The reference is only used if the controlPlaneTransportOption is set to
ATM.
Dependencies: Must not be set to the same value as uniSaalTpRef2 on
this MO, and not to the same value as uniSaalTpRef1/2 on
NbapDedicated. Both uniSaalTpRef1 and uniSaalTpRef2 on this MO must
not be NULL in case Iub::controlPlaneTransportOption.atm = true.

NbapCommon

uniSaalTpRef2

RBS DUW

Reference to the UniSaalTp instance used for the secondary signalling


UniSaalTp
bearer. The reference is only used if the controlPlaneTransportOption is set
to ATM.
Dependencies: Must not be set to the same value as uniSaalTpRef1 on
this MO, and not to the same value as uniSaalTpRef1/2 on
NbapDedicated. Both uniSaalTpRef1 and uniSaalTpRef2 on this MO must
not be NULL in case Iub::controlPlaneTransportOption.atm = true.

NbapCommon
NbapCommon

userLabel
userLabel

RBS DUW
RNC

NbapDedicated

activeBearer

RBS DUW

Label for free use.


Provides the possibility to put a user-friendly label on the MO instance.
The value is not used by the RNC.
Specifies which UniSaalTp is active when ATM is transport bearer alt. that
Sctp is active when IPv4 is bearer.

string
string
Nbap_ActiveBearer

Possible values:
NONE = No active bearer.
UNI_SAAL_TP_REF1 = Attribute uniSaalTpRef1 is used.
UNI_SAAL_TP_REF2 = Attribute uniSaalTpRef2 is used.
SCTP_REF = Attribute sctpRef is used.
NbapDedicated

activeUniSaalTpRef

RNC

UniSaalTp

RNC

Reference to the UniSaalTp Managed Object that represents the active


UNI SAAL termination point.
The administrative state of the signaling link.

NbapDedicated

administrativeState

NbapDedicated

availabilityStatus

RBS DUW

The availability status of the protocol termination.

AvailabilityStatus

Possible values:
NOT_INSTALLED
POWER_OFF
IN_TEST
DEPENDENCY_LOCKED
DEPENDENCY_FAILED
FAILED
OFF_LINE
DEGRADED
OFF_DUTY
LOG_FULL
NO STATUS = Full availability.

SupportedAdminStates

NONE = 0
UNI_SAAL_TP_REF1 = 1
UNI_SAAL_TP_REF2 = 2
SCTP_REF = 3

LOCKED = 0
UNLOCKED = 1
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
NO_STATUS = 0

LOCKED(0)

Specification: ITU-T rec. X.731

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

166 (520)

NbapDedicated

availabilityStatus

RNC

The availability status of the NBAP dedicated signaling bearer.


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9, bit 10 or bit 11 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED
Bit 11 = 1: DEPENDENCYSHUTTINGDOWN

long

0..4095

NbapDedicated

l2EstablishReqRetryT

RBS DUW

Time between successive attempts to establish layer 2 communication.

long

1..150

long

1..600

30

30

Unit: 1 s
NbapDedicated

l2EstablishSupervisionT

RBS DUW

Maximum allowed time to establish layer 2 communication.


Unit: 1 s

NbapDedicated
NbapDedicated
NbapDedicated

NbapDedicatedId
NbapDedicatedId
operationalState

RBS DUW
RNC
RBS DUW

The value component of the RDN.


Naming attribute. Contains the value part of the RDN.
Defines the operational state.

string
string
OperState

DISABLED = 0
ENABLED = 1

Possible values:
DISABLED
ENABLED
Specification: ITU-T rec. X.731
NbapDedicated

operationalState

RNC

The operational state of the NBAP dedicated signaling bearer.

SupportedOperStates

NbapDedicated

sctpRef

RBS DUW

NbapDedicated

standbyUniSaalTpRef

RNC

NbapDedicated

uniSaalTpRef1

RBS DUW

Reference to the Sctp instance used. The reference is only used if the
Sctp
controlPlaneTransportOption is set to IPv4.
Reference to the UniSaalTp Managed Object that represents the stand-by UniSaalTp
UNI SAAL termination point.
Reference to the UniSaalTp instance used for the primary signalling bearer. UniSaalTp
The reference is only used if the controlPlaneTransportOption is set to
ATM.

DISABLED = 0
ENABLED = 1

Dependencies: Must not be set to the same value as uniSaalTpRef2 on


this MO, and not to the same value as uniSaalTpRef1/2 on NbapCommon.
Both uniSaalTpRef1 and uniSaalTpRef2 on this MO must not be NULL in
case Iub::controlPlaneTransportOption.atm = true.
NbapDedicated

uniSaalTpRef2

RBS DUW

Reference to the UniSaalTp instance used for the secondary signalling


UniSaalTp
bearer. The reference is only used if the controlPlaneTransportOption is set
to ATM.
Dependencies: Must not be set to the same value as uniSaalTpRef1 on
this MO, and not to the same value as uniSaalTpRef1/2 on NbapCommon.
Both uniSaalTpRef1 and uniSaalTpRef2 on this MO must not be NULL in
case Iub::controlPlaneTransportOption.atm = true.

NbapDedicated
NbapDedicated

userLabel
userLabel

RBS DUW
RNC

NextHop

nexthop

RBS 6401

Prepared: EZIEAGA

Label for free use.


Provides the possibility to put a user-friendly label on the MO instance.
The value is not used by the RNC.
Nexthop information

Date: 2014-05-27
Sheet: 14.0.2

string
string
NextHopInfo

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

167 (520)

NextHop

nexthop.reference

RBS 6401

Static Route Nexthop Information. _x000D_


Following nexthops types are referenced:_x000D_
- IP peer

ManagedObject

NextHop
NniSaalProfile

nextHopId
NniSaalProfileId

RBS 6401
RNC

Static Route Next Hop Id.


The value component of the RDN.

string
string

NniSaalProfile

profileData

RNC

Struct containing profile data.

NniSaalProfileData

NniSaalProfile

profileData.congestionLevel1Abatement

RNC

When the current send buffer occupancy decreases below


congestionLevel1Abatement, the MTP3b congestion status of the internal
signalling link changes from 1 to 0.

long

0..100

60

60

This attribute must follow the rule: 0 <=


congestionLevel1Abatement < congestionLevel1OnSet.
NniSaalProfile

profileData.congestionLevel1OnSet

RNC

When the current send buffer occupancy increases above the


long
congestionLevel1Onset, a congestion indication is sent to MTP3b and the
MTP3b congestion status of the internal signalling link changes from 0 to 1.

0..100

70

70

NniSaalProfile

profileData.congestionLevel2Abatement

RNC

When the current send buffer occupancy decreases below


long
congestionLevel2Abatement, but is not below congestionLevel1Abatement,
the MTP3b congestion status of the internal signalling link changes from 2
to 1.

0..100

71

71

This attribute must follow the rule: congestionLevel1OnSet <=


congestionLevel2Abatement < congestionLevel2OnSet.
NniSaalProfile

profileData.congestionLevel2OnSet

RNC

When the current send buffer occupancy increases above the


long
congestionLevel2Onset, a congestion indication is sent to MTP3b and the
MTP3b congestion status of the internal signalling link changes from 1 to 2.

0..100

80

80

NniSaalProfile

profileData.congestionLevel3Abatement

RNC

When the current send buffer occupancy decreases below


long
congestionLevel3Abatement, but is not below congestionLevel2Abatement,
the MTP3b congestion status of the internal signalling link changes from 3
to 2.

0..100

81

81

This attribute must follow the rule: congestionLevel2OnSet <=


congestionLevel3Abatement < congestionLevel3OnSet.
NniSaalProfile

profileData.congestionLevel3OnSet

RNC

When the current send buffer occupancy increases above the


long
congestionLevel3Onset, a congestion indication is sent to MTP3b and the
MTP3b congestion status of the internal signalling link changes from 2 to 3.

0..100

90

90

NniSaalProfile

profileData.discardMessagesLevel1

RNC

When the current send buffer occupancy exceeds discardMessagesLevel1, long


but does not exceed discardMessagesLevel2, the MTP3b will discard
messages with priority 0.

0..100

80

80

0..100

90

90

This attribute must follow the rule: congestionLevel1OnSet <


discardMessagesLevel1 <= congestionLevel2OnSet.

NniSaalProfile

profileData.discardMessagesLevel2

RNC

When the current send buffer occupancy exceeds discardMessagesLevel2, long


but does not exceed discardMessagesLevel3, the MTP3b will discard
messages with priority 0 and 1.
This attribute must follow the rule: congestionLevel2OnSet <
discardMessagesLevel2 <= congestionLevel3OnSet.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
NniSaalProfile

profileData.discardMessagesLevel3

RNC

Network Parameters

When the current send buffer occupancy exceeds discardMessagesLevel3, long


the MTP3b will discard messages with priority 0, 1 and 2.

168 (520)
0..100

95

100

This attribute must follow the rule: congestionLevel3OnSet <


discardMessagesLevel3 <= 100.

NniSaalProfile

profileData.initialCredit

RNC

The initial number of credits.

long

10..1000

250 See CPI

long

0..100

long

0..100

long

0..10000

25 See CPI

3..1001

67

67

For 64 kbit/s, use 30.


This attribute must follow the rule, initialCredit > maxPD.
Unit: 1 transmitted PDUs.
NniSaalProfile

profileData.maxCC

RNC

The maximum number of retransmissions of Protocol Data Units (PDU):


BGN, END, ER, RS.

NniSaalProfile

profileData.maxNRP

RNC

The maximum number of retransmissions of PDUs during proving to


consider proving successful.

NniSaalProfile

profileData.maxPD

RNC

The maximum number of SD PDUs before a poll is sent.

Unit: 1 transmitted PDUs.

Unit: 1 transmitted PDUs.

This attribute must follow the rule, maxPD < initialCredit.


Unit: 1 transmitted PDUs.
NniSaalProfile

profileData.maxStat

RNC

The maximum number, odd integer value, of list elements placed in a STAT long
PDU.
The maxStat attribute is controlled by the AAL5 maximum SDU size
defined in the Aal5TpVccTp MO. The maxStat times 4 (octets) plus
additional 12 octets (for header) must not exceed the AAL5 maximum SDU
size (lower of the two directions, fromUserMaxSduSize and
toUserMaxSduSize).
The consistency check is performed when the NniSaalTp MO is
created, as there is no relation between the NniSaalProfile MO and the
Aal5TpVccTp MO.
Unit: 1 transmitted PDUs.

NniSaalProfile

profileData.mps

RNC

The Management Proving Status (MPS) which is used to determine


whether for proving is done during setup of the SAAL connection.

long

0..2

mps = 0 (NORMAL) If set to 0, normal proving is done regardless of


the incoming SSCOP-UU or the local User Part Proving Status set by
MTPL3
mps = 1 (EMERGENCY) If set to 1, emergency proving is done
regardless of the incoming SSCOP-UU or the local User Part Proving
Status set by MTPL3
mps = 2 (NEUTRAL) If set to 2, proving depends on the incoming
SSCOP-UU as well as the local User Part Proving Status set by MTPL3.
More information on MPS can be found in table 7 of ITU
specification Q.2140

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
NniSaalProfile

profileData.nrOfPDUsDuringProving

RNC

Network Parameters

The length of proving in terms of number of transmitted PDUs (n1).

169 (520)

long

0..100000

1000

1000

long

10..10000

200

200

10..10000

100 See CPI

10..10000

100 See CPI

This attribute must follow the rule, timerT2 > 2 *


nrOfPDUsDuringProving * timerT3 * t3Factor.
The t3Factor describes (approximately) the relationship between
the configured value and the actual value of timerT3, and is determined as
follows:
timerT3(ms)
5-6 ms (t3Factor 2.5)
7-13 ms (t3Factor 2.0)
14- ms (t3Factor 1.5)
Unit: 1 transmitted PDUs
NniSaalProfile

profileData.timerCC

RNC

The timer determining the time between retransmission of PDUs: BGN,


END, ER, RS.
It should be more than the roundtrip delay.
Unit: 1 ms

NniSaalProfile

profileData.timerIdle

RNC

The timer running when there are no PDUs to transmit and there are no
long
outstanding acknowledgements or data pending for credit. When this timer
is running, no POLL PDUs are sent.
This timer should be significantly greater than the value of
timerKeepAlive.

NniSaalProfile

profileData.timerKeepAlive

RNC

The timer to be used during a period of no outstanding acknowledgements long


or new data pending receipt of credit. At timeout, the peer is polled to see if
it is alive. The timer determines the interval between polls in the transient
phase. This timer should be greater than the roundtrip delay and also
greater than timerPoll.

Unit: 1 ms

Unit: 1 ms
NniSaalProfile

profileData.timerNoCredit

RNC

The maximum time of no credit. If the timer expires, the assured data
transfer mode is released.

NniSaalProfile

profileData.timerNoResponse

RNC

The timer to determine the maximum time interval, during which reception
of at least one STAT PDU is expected as a response to a poll.

long

0..100000

1500

long

10..100000

500 See CPI

long

10..100000

50 See CPI

long

0..86400000

long

10..100000

1500

Unit: 1 ms

This attribute must follow the rule, timerNoResponse >=


timerKeepAlive + one roundtrip delay
Unit: 1 ms
NniSaalProfile

profileData.timerPoll

RNC

The timer that specifies the maximum time between sending of POLL
PDUs to the peer receiver during other traffic (active phase).

NniSaalProfile

profileData.timerRepeatSrec

RNC

The timer which is set whenever a report of SSCOP recovery is received


from the SSCF. If the timer is running when another report of recovery is
received, the assured data transfer mode is released. If the timer expires,
nothing is done.

NniSaalProfile

profileData.timerT1

RNC

The timer between the link release action and the next link re-establish
action during the alignment. When timer T1 expires, a new attempt is
made to set up assured data transfer mode to the peer.

Unit: 1 ms
3600000

3600000

5000

5000

Unit: 1 ms

Unit: 1 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

NniSaalProfile

profileData.timerT2

RNC

The total time that SSCF attempts alignment. When timer T2 expires, the
alignment procedure is interrupted.

NniSaalProfile

profileData.timerT3

RNC

The time between proving PDUs. The timer is set so that loading of the
signalling link is approximately 50% of it's nominal rate.

170 (520)

long

10..200000

long

5..1000

30000

30000

128

276

Unit: 1 ms

This attribute must follow the rule, timerT2 > 2 *


nrOfPDUsDuringProving * timerT3 * t3Factor.
The t3Factor describes (approximately) the relationship between
the configured value and actual value of the timerT3, and is determined as
follows:
timerT3(ms) t3Factor
5-6
2.5
7-13
2.0
14 1.5
Unit: 1 ms
NniSaalProfile

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

NniSaalTp

NniSaalProfile

userLabel

RNC

Label for free use.

string

NniSaalTp

aal5TpVccTpId

RNC

The reference to an instance of an Aal5TpVccTp MO.

Aal5TpVccTp

The AAL5 termination point must terminate on a main processor.

NniSaalTp

maxSduSize

RNC

The maximum SAAL SDU size. The attribute is dependent on the


maximum SDU size for AAL5, defined in Aal5TpVccTp. The attribute,
maxSduSize must be 4 bytes less than the maximum SDU size for AAL5
(the lower of the two attributes, fromUserMaxSduSize and
toUserMaxSduSize).

long

128..2044

Additional to the value of the maxSduSize, 4 bytes are used by the


SAAL layer for the SAAL header
Example: If fromUserMaxSduSize is set to 256 and
toUserMaxSduSize is set to 512 in the Aal5TpVccTp MO, maxSduSize in
the NniSaalTp MO may not exceed 252.
The upper limit of 2044 (2048 including the SAAL header) is due to
limitations on the AAL5 layer.
The default value for maxSduSize is the minimum value and it must
normally be increased.

NniSaalTp

nniSaalProfileId

RNC

The Reference to an instance of a NniSaalProfile MO.

NniSaalProfile

The maxStat attribute defined in the NniSaalProfile MO is controlled


by the AAL5 SDU size defined in the Aal5TpVccTp MO. See the description
of the maxStat attribute in the NniSaalProfile MO.
The consistency check of the attributes in these two MOs is
performed by the NniSaalTp.
NniSaalTp

NniSaalTpId

RNC

The value component of the RDN.

string

NniSaalTp

operationalState

RNC

The operational state.

OperState

NniSaalTp

reservedBy

RNC

Contains an MO instance that reserves this MO instance.

ManagedObject

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

171 (520)

NniSaalTp

userLabel

RNC

Label for free use.

string

NodeBFunction

nbapDscp

RBS DUW

Differentiated Services Code Point (DSCP) value for NBAP-C and NBAPD.

long

Os155SpiTtp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Os155SpiTtp

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Os155SpiTtp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

0..63

Takes effect: At next restart.

It contains details about operationalState.

Os155SpiTtp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Os155SpiTtp

lineNo

RBS DUW

The line number.

long

1..8

long

1..8

The maximum range of this attribute can vary between the boards. See the
description of the relevant board for details.
Os155SpiTtp

lineNo

RNC

The line number.


The maximum range of this attribute can vary between the boards.
See the description of the relevant board for details.

Os155SpiTtp

loopBack

RBS DUW

The loopback state of this physical path termination.

Os155LoopBack

NONE = 0
LINE = 1

NONE(0)

NONE(0)

Os155LoopBack

NONE = 0
LINE = 1

NONE(0)

NONE(0)

The attribute administrativeState must be set to LOCKED when setting the


attribute loopBack.
Os155SpiTtp

loopBack

RNC

The loopback state of this physical path termination.


The attribute administrativeState must be set to LOCKED when
setting the attribute loopBack.

Os155SpiTtp

msAisReporting

RBS DUW

Indicates whether the alarm Multiplexer Section (MS) Alarm Indication


Signal (AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Os155SpiTtp

msAisReporting

RNC

Network Parameters

Indicates whether the alarm Multiplexer Section (MS) Alarm Indication


Signal (AIS) is to be issued.

172 (520)

boolean

true - enable reporting.


false - disable reporting.
Os155SpiTtp

msDegM

RBS DUW

Specifies the number of bad seconds in a continuous measurement period long


that causes a MS Degraded Signal alarm.

2..10

2..10

0..100

30

0..100

30

See the explanation of bad seconds in attribute msDegThreshold.


Dependencies: This attribute is applicable only if the supervisionMode has
value BURSTY.
Os155SpiTtp

msDegM

RNC

Specifies the number of bad seconds in a continuous measurement period long


that causes a MS Degraded Signal alarm.
See the explanation of bad seconds in attribute msDegThreshold.
Dependencies: This attribute is applicable only if the
supervisionMode has value BURSTY.

Os155SpiTtp

msDegThreshold

RBS DUW

Specifies the number of received blocks that are allowed to have bit errors. long
The measurement is taken every second. If the threshold is exceeded, that
second is considered as a bad second.
Unit: 1 %
Dependencies: This attribute is applicable only if the supervisionMode has
value BURSTY.

Os155SpiTtp

msDegThreshold

RNC

Specifies the number of received blocks that are allowed to have bit errors. long
The measurement is taken every second. If the threshold is exceeded, that
second is considered as a bad second.
Unit: 1 %
Dependencies: This attribute is applicable only if the
supervisionMode has value BURSTY.

Os155SpiTtp

msRdiReporting

RBS DUW

Indicates whether the alarm Multiplexer Section (MS) Remote Defect


Indication (RDI) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Os155SpiTtp

msRdiReporting

RNC

Indicates whether the alarm Multiplexer Section (MS) Remote Defect


Indication (RDI) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Os155SpiTtp

muxMode

RBS DUW

The level at which the STM-1 or OC3 signal is demultiplexed.

MuxMode

STANDBY = 0
E1_T1_HG_LEVEL = 1
VC4_STS3CSPE_LEVEL = 2

Os155SpiTtp

muxMode

RNC

The level at which the STM-1 or OC3 signal is demultiplexed.

MuxMode

STANDBY = 0
E1_T1_HG_LEVEL = 1
VC4_STS3CSPE_LEVEL = 2

Os155SpiTtp

operationalState

RBS DUW

The operational state.

OperState

Os155SpiTtp

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Os155SpiTtp
Os155SpiTtp

Os155SpiTtpId
Os155SpiTtpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Os155SpiTtp

poissonDegThreshold

RBS DUW

Network Parameters

Specifies the maximum Bit Error Rate (BER) for the MS Degraded Signal
(MS-DEG) alarm.

173 (520)

long

5..9

long

5..9

BER is the ratio of the erroneous bits detected to the number of bits
transmitted.
The attribute gives a maximum BER of 10e-poissonDegThreshold.
If the threshold is exceeded, the MS-DEG alarm is issued.
Dependencies: This attribute is applicable only if the supervisionMode has
value POISSON.
Os155SpiTtp

poissonDegThreshold

RNC

Specifies the maximum Bit Error Rate (BER) for the MS Degraded Signal
(MS-DEG) alarm.
BER is the ratio of the erroneous bits detected to the number of bits
transmitted.
The attribute gives a maximum BER of 10e-poissonDegThreshold.
If the threshold is exceeded, the MS-DEG alarm is issued.
Dependencies: This attribute is applicable only if the
supervisionMode has value POISSON.

Os155SpiTtp
Os155SpiTtp

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

Os155SpiTtp

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

Os155SpiTtp

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

Os155SpiTtp

sfpInformation

RBS DUW

Indicates information about the SfpPort.

SfpInformation

If sfpPort is false, this attribute is not applicable.


Os155SpiTtp

sfpInformation

RNC

Indicates information about the SfpPort.

SfpInformation

If sfpPort is false, this attribute is not applicable.


Os155SpiTtp
Os155SpiTtp

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

RBS DUW
RNC

The product number of an SFP module.


The product number of an SFP module.

string
string

Os155SpiTtp

sfpInformation.sfpState

RBS DUW

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

Os155SpiTtp

sfpInformation.sfpState

RNC

The state of the SFP port.

SfpState

VALID = 0
INVALID = 1
NOT_INSTALLED = 2
NOT_APPLICABLE = 3

Os155SpiTtp

sfpInformation.sfpType

RBS DUW

The type of SFP.

string

Os155SpiTtp

sfpInformation.sfpType

RNC

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


The type of SFP.

string

Example: GE_1000_BASE_T or GE_1000_BASE_CX.


Os155SpiTtp

sfpPort

RBS DUW

Indicates if the port is an SFP port.

boolean

Autonegotiation must be configured to true for an SFP port. Otherwise, the


port may be disabled.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Os155SpiTtp

sfpPort

RNC

Network Parameters

Indicates if the port is an SFP port.

174 (520)

boolean

Autonegotiation must be configured to true for an SFP port.


Otherwise, the port may be disabled.
Os155SpiTtp

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
Os155SpiTtp

shutDownTimeout

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

Os155SpiTtp

standardMode

RBS DUW

The standard that this MO complies to.

StandardMode

ANSI = 0
ETSI = 1
TTC = 2

Os155SpiTtp

standardMode

RNC

The standard that this MO complies to.

StandardMode

ANSI = 0
ETSI = 1
TTC = 2

Os155SpiTtp

supervisionMode

RBS DUW

Os155SpiTtp

supervisionMode

RNC

Controls if the detection of the MS-DEG alarm should assume Poisson or SigQSupervisionMode
Bursty distribution of errors.
Controls if the detection of the MS-DEG alarm should assume Poisson or SigQSupervisionMode
Bursty distribution of errors.

Os155SpiTtp
Os155SpiTtp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Ospf

administrativeState

RBS DUW

The administrative state.

Ospf

administrativeState

RNC

Ospf

availabilityStatus

RBS DUW

BURSTY = 1
POISSON = 2
BURSTY = 1
POISSON = 2

BURSTY(1)

BURSTY(1)

BURSTY(1)

BURSTY(1)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ospf

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

175 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

Ospf
Ospf

ipMo
ipMo

RBS DUW
RNC

Contains a reference to an Ip MO instance that reserves this MO.


Contains a reference to an Ip MO instance that reserves this MO.

Ip
Ip

Ospf

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1

OperState

DISABLED = 0
ENABLED = 1

This attribute can only be set to ENABLED when the attribute,


workingMode in Ip MO is set to ROUTER_MODE.
Ospf

operationalState

RNC

The operational state.


This attribute can only be set to ENABLED when the attribute,
workingMode in Ip MO is set to ROUTER_MODE.

Ospf

ospfAreaBdrRtrStatus

RBS DUW

Ospf

ospfAreaBdrRtrStatus

RNC

Area border router flag.

boolean

Indicates whether the router is acting as an area border router or not.


Area border router flag.

boolean

Indicates whether the router is acting as an area border router or


not.
Ospf

ospfASBdrRtrStatus

RBS DUW

Specifies whether this router is configured as an Autonomous System


border router.

boolean

This attribute must be set to true if the user wants to configure static routes,
which are distributed to other OSPF routes as external routes.
Configuration of static routes is the same as adding and deleting static
routes to the IpRoutingTable MO.
Ospf

ospfASBdrRtrStatus

RNC

Specifies whether this router is configured as an Autonomous System


border router.

boolean

This attribute must be set to true if the user wants to configure static
routes, which are distributed to other OSPF routes as external routes.
Configuration of static routes is the same as adding and deleting
static routes to the IpRoutingTable MO.

Ospf
Ospf

OspfId
OspfId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Ospf

ospfRouterId

RBS DUW

This attribute has the format of an IP address.

string

To set this attribute, administrativeState has to be set to LOCKED.


The ospfRouterId is uniquely identifying the router in the Autonomous
System. By convention to ensure uniqueness, this is configured to the
value of one of the router's IP interface addresses.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ospf

ospfRouterId

RNC

Network Parameters

This attribute has the format of an IP address.

176 (520)

string

To set this attribute, administrativeState has to be set to LOCKED.


The ospfRouterId is uniquely identifying the router in the
Autonomous System. By convention to ensure uniqueness, this is
configured to the value of one of the router's IP interface addresses.

Ospf

recoverTopoDb

RBS DUW

Ospf

recoverTopoDb

RNC

Ospf

topoDbStoreInterv

RBS DUW

Ospf

topoDbStoreInterv

RNC

Indicates whether the topology database is to be recovered from the


database at restart.
Indicates whether the topology database is to be recovered from the
database at restart.

boolean

The interval with which the topology database is stored.

long

60

long

60

boolean

Unit: 1 s
The interval with which the topology database is stored.
Unit: 1 s
Ospf
Ospf

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

OspfArea

areaId

RBS DUW

The OSPF area identity in form of an IP address. This areId uniquely


identifies the area.

string

AreaId 0.0.0.0 is used for the OSPF backbone.


Range: 000.000.000.000 to 255.255.255.255.
OspfArea

areaId

RNC

The OSPF area identity in form of an IP address. This areId uniquely


identifies the area.

string

AreaId 0.0.0.0 is used for the OSPF backbone.


Range: 000.000.000.000 to 255.255.255.255.
OspfArea

areaLsaChecksum

RBS DUW

Represents 32-bit unsigned sum of the link-state advertisements LS check- long


sums contained in this area's link-state database.
Represents 32-bit unsigned sum of the link-state advertisements LS check- long
sums contained in this area's link-state database.

OspfArea

areaLsaChecksum

RNC

OspfArea

importExternalLsa

RBS DUW

Specifies whether importing Autonomous System external LSAs is


supported.
Specifies whether importing Autonomous System external LSAs is
supported.

boolean

OspfArea

importExternalLsa

RNC

OspfArea
OspfArea

OspfAreaId
OspfAreaId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

OspfArea
OspfArea

range0
range0

RBS DUW
RNC

OspfArea IP address range zero (0).


OspfArea IP address range zero (0).

OspfAreaRange
OspfAreaRange

OspfArea
OspfArea

range0.advertise
range0.advertise

RBS DUW
RNC

Indicates whether the area range should be advertised into OSPF.


Indicates whether the area range should be advertised into OSPF.

boolean
boolean

OspfArea

range0.ipAddress

RBS DUW

The subnet address of the range.

string

OspfArea

range0.ipAddress

RNC

The subnet address of the range.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

boolean

0000.0000.0000.0
000
0000.0000.0000.0
000

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
OspfArea

range0.subnetMask

RBS DUW

Network Parameters

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0 (zero).

177 (520)
0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

OspfArea

range0.subnetMask

RNC

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0
(zero).

0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

OspfArea
OspfArea

range1
range1

RBS DUW
RNC

OspfArea IP address range one (1).


OspfArea IP address range one (1).

OspfAreaRange
OspfAreaRange

OspfArea
OspfArea

range1.advertise
range1.advertise

RBS DUW
RNC

Indicates whether the area range should be advertised into OSPF.


Indicates whether the area range should be advertised into OSPF.

boolean
boolean

OspfArea

range1.ipAddress

RBS DUW

The subnet address of the range.

string

OspfArea

range1.ipAddress

RNC

The subnet address of the range.

string

OspfArea

range1.subnetMask

RBS DUW

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0 (zero).

0000.0000.0000.0
000
0000.0000.0000.0
000
0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
OspfArea

range1.subnetMask

RNC

Network Parameters

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0
(zero).

178 (520)
0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

OspfArea
OspfArea

range2
range2

RBS DUW
RNC

OspfArea IP address range two (2).


OspfArea IP address range two (2).

OspfAreaRange
OspfAreaRange

OspfArea
OspfArea

range2.advertise
range2.advertise

RBS DUW
RNC

Indicates whether the area range should be advertised into OSPF.


Indicates whether the area range should be advertised into OSPF.

boolean
boolean

OspfArea

range2.ipAddress

RBS DUW

The subnet address of the range.

string

OspfArea

range2.ipAddress

RNC

The subnet address of the range.

string

OspfArea

range2.subnetMask

RBS DUW

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0 (zero).

0000.0000.0000.0
000
0000.0000.0000.0
000
0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

OspfArea

range2.subnetMask

RNC

IP subnet mask of the range to be added.


string
The subnet mask must be contigouos. That is, has the LSB set to 0
(zero).

0000.0000.0000.0
000

Example:
255.255.255.X
Contiguous subnet mask:
11111111.11111111.11111111.11111110 (X = 254)
11111111.11111111.11111111.11111100 (X = 252)
Non-contiguous subnet mask:
11111111.11111111.11111111.11111010 (X = 250)

OspfArea
OspfArea

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

OspfArea

sendAreaSummary

RBS DUW

OspfArea

sendAreaSummary

RNC

Specifies whether the router originates and propagates summary LSAs into boolean
a stub-area.
Specifies whether the router originates and propagates summary LSAs into boolean
a stub-area.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

OspfInterface
OspfInterface
0

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

179 (520)

OspfArea
OspfArea

stubArea
stubArea

RBS DUW
RNC

Specifies whether the OSPF area is a stub area or not.


Specifies whether the OSPF area is a stub area or not.

boolean
boolean

OspfArea

stubAreaMetric

RBS DUW

Cost for default router when the router advertises into a stub area and the
router is an area border router.

long

long

This attribute is set by default to the least metric among the interfaces to
other areas.
OspfArea

stubAreaMetric

RNC

Cost for default router when the router advertises into a stub area and the
router is an area border router.
This attribute is set by default to the least metric among the
interfaces to other areas.

OspfArea

stubAreaMetricType

RBS DUW

Stub area metric type.

OspfMetricType

COMPARABLE_COST = 0
NON_COMPARABLE = 1

COMPARABLE_C
OST(0)

OspfMetricType

COMPARABLE_COST = 0
NON_COMPARABLE = 1

COMPARABLE_C
OST(0)

RFC 1850 (OSPF V2 MIB):


comparableCost (external type 1)
nonComparable (external type 2)
OspfArea

stubAreaMetricType

RNC

Stub area metric type.


RFC 1850 (OSPF V2 MIB):
comparableCost (external type 1)
nonComparable (external type 2)

OspfArea
OspfArea

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

OspfInterface

helloInterval

RBS DUW

The time between sending OSPF Hello-packets over the interface.

long

10

long

10

This attribute must have a positive value.


Unit: 1 s
OspfInterface

helloInterval

RNC

The time between sending OSPF Hello-packets over the interface.


This attribute must have a positive value.
Unit: 1 s

OspfInterface

interfacePriority

RBS DUW

The interface priority. Each router is configured with a priority configured


from 0 - 255 where 0 is the lowest priority and 255 the highest.

long

0..255

long

0..255

This attribute must have a positive value.


OspfInterface

interfacePriority

RNC

The interface priority. Each router is configured with a priority configured


from 0 - 255 where 0 is the lowest priority and 255 the highest.
This attribute must have a positive value.

OspfInterface

interfaceTransitDelay

RBS DUW

Estimated delay for the transmission of a link state update package over
the interface.

OspfInterface

interfaceTransitDelay

RNC

Estimated delay for the transmission of a link state update package over
the interface.

OspfInterface

lsaTransmissionInterval

RBS DUW

The time between LSA re-transmissions over the interface.

long

long

long

Unit: 1 s

Unit: 1 s

Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
OspfInterface

lsaTransmissionInterval

RNC

Network Parameters

The time between LSA re-transmissions over the interface.

180 (520)

long

Unit: 1 s
The identity of the OspfArea connected to this OspfInterface. The default
value is the default OspfArea MO.
The identity of the OspfArea connected to this OspfInterface. The default
value is the default OspfArea MO.

OspfArea

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

RBS DUW

Each OSPF interface is connected to one IP link.

ManagedObject

OspfInterface

ospfAreaRelated

RBS DUW

OspfInterface

ospfAreaRelated

RNC

OspfInterface
OspfInterface

OspfInterfaceId
OspfInterfaceId

OspfInterface

relatedLink

OspfArea

The relatedLink can be either an IpAtmLink or an EthernetLink MO


reference.
OspfInterface

relatedLink

RNC

Each OSPF interface is connected to one IP link.

ManagedObject

The relatedLink can be either an IpAtmLink or an EthernetLink MO


reference.
OspfInterface

routerDeadInterval

RBS DUW

The time after which a neighbor router is declared dead when not heard
from.

long

40

OspfInterface

routerDeadInterval

RNC

The time after which a neighbor router is declared dead when not heard
from.

long

40

OspfInterface
OspfInterface

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

PacketDataRouter

aal5TpRef

RNC

Reference to the Aal5TpVccTp MO instance that represents the Core


Network AAL5 connection endpoint.

Aal5TpVccTp

Unit: 1 s

Unit: 1 s

Dependencies: The Aal5TpVccTp MO has a reference to a Spm MO. The


PdrDevice that is parent to this PacketDataRouter should refer to the same
Spm MO.
PacketDataRouter

administrativeState

RNC

The administrative state of the Packet Data Router.

SupportedAdminStates

PacketDataRouter

availabilityStatus

RNC

The availability status of the Packet Data Router.


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9, 10 or 11 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED
Bit 11 = 1: DEPENDENCYSHUTTINGDOWN

long

PacketDataRouter

cnIuLinkIpAddress

RNC

IP address at the CN side of the IuLink, e.g. in ATM VC terminating router


or one of the IP addresses in SGSN, used for IP level ping link or network
supervision.
The input format used by the operator is four fields of digits, separated by
dots. The numeric value of each field shall be in the range 0..255.

string

PacketDataRouter

operationalState

RNC

The operational state of the Packet Data Router.

SupportedOperStates

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

LOCKED = 0
UNLOCKED = 1

LOCKED(0)

0..4095

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Naming attribute. Contains the value part of the RDN.


Set by the RNC to a sequential number.
List of references, updated automatically by the RNC, that point back
toward the MO instances that have references to this MO instance.

181 (520)

PacketDataRouter

PacketDataRouterId

RNC

PacketDataRouter

reservedBy

RNC

string

PacketDataRouter

rncIpAddress

RNC

The IP address of the AAL5 TP terminated in the router processor.


The input format used by the operator is four fields of digits, separated by
dots. The numeric value of each field shall be in the range 0..255.

string

PacketDataRouter
PacketDataRouter

timeToLive
userLabel

RNC
RNC

long
string

PacketFrequencySyncRef

administrativeState

RBS DUW

Time-to-live value assigned to uplink traffic IP header.


Provides the possibility to put a user-friendly label on the MO instance.
The value is not used by the RNC.
The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

PacketFrequencySyncRef

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

IuLink

Sequence length must be in the range 0..16

0..255

It contains details about operationalState.

PacketFrequencySyncRef

cachedIpAddress

RBS DUW

Indicates the latest IP address received from the DNS server with the
specified domain name. If domain name is not valid or no value yet
received from the DNS server this will be a null string.

string

PacketFrequencySyncRef
PacketFrequencySyncRef

dscp
ipAccessHostEtRef

RBS DUW
RBS DUW

The dscp value used for IP transmitted packets.


Reference to an instance of a IpAccessHostEt MO.

long
IpAccessHostEt

20

0..63

20

LOCKED(0)

54

The attribute administrativeState must be set to LOCKED before modifying


this attribute.
PacketFrequencySyncRef

operationalState

RBS DUW

The operational state.

OperState

PacketFrequencySyncRef

PacketFrequencySyncRefId

RBS DUW

The value component of the RDN.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
PacketFrequencySyncRef

packetSyncStatus

RBS DUW

Network Parameters

Packet synchronization status.

182 (520)

long

The value is a bitmap, displayed as a decimal value. If there are several


faults, the value is the sum of the individual values for each fault, as
specified below:
0 NO_FAULT: The reference can be selected as a synchronization
reference.
1 NO_ANNOUNCE: No Announce messages have been received from the
PTP server within the past 8 seconds.
2 CLOCK_CLASS: The clockClass of the grandMaster clock, reported by
the PTP server in Announce messages, is not less than or equal to 7
(PacketTimeSyncRef) or 14 (PacketFrequencySyncRef).
4 CLOCK_ACCURACY: The clockAccuracy of the grandMaster clock,
reported by the PTP server in Announce messages, is not less than or
equal to hexadecimal 22 (that is, 34 in decimal).
8 NO_SYNC: No Sync messages have been received from the PTP server
within the past 8 seconds.
16 ERRATIC_SYNC: Sync messages are arriving irregularly but are not
totally missing. This could indicate packet loss in the network.
32 LOW_SYNC_RATE: The PTP server states that the intended interval
between Sync messages is too long to meet the needs of the ordinary
clock slave.
64 NO_DELAY_RESP: There has been no Delay_Resp from the PTP
server for the last 8 Delay_Req messages sent to it. For the first
Delay_Req, this indication is set after only 2 missed responses (with initial
request interval 8 seconds).

PacketFrequencySyncRef

ptpDomain

RBS DUW

128 LOW_DELAY_REQ_RATE: The PTP server in its Delay_Resp


messagesthe
states
minimum allowed interval between Delay_Req
Specifies
PTPadomain.

long

0..255

Has to be a unique number among the configured packetTimeSyncRef and


packetFrequencySyncRef objects.
The attribute administrativeState must be set to LOCKED before modifying
this attribute.
PacketFrequencySyncRef
PacketFrequencySyncRef
PacketFrequencySyncRef

ptpGrandMasterIdentity
ptpOwnPortIdentity
ptpOwnPortIdentity.clockIdentity

RBS DUW
RBS DUW
RBS DUW

PacketFrequencySyncRef
PacketFrequencySyncRef
PacketFrequencySyncRef

ptpOwnPortIdentity.ptpPortNumber
ptpParentPortIdentity
ptpParentPortIdentity.clockIdentity

RBS DUW
RBS DUW
RBS DUW

PacketFrequencySyncRef
PacketFrequencySyncRef
PacketFrequencySyncRef

ptpParentPortIdentity.ptpPortNumber
ptpQualityLevel
reservedBy

RBS DUW
RBS DUW
RBS DUW

The grand master port that sends synchronization messages.


The own port identity.
The clock identity.

string
PtpPortIdentity
string

The value is presented as a hexadecimal value.


The port number.
The parent port that sends synchronization messages.
The clock identity.

long
PtpPortIdentity
string

The value is presented as a hexadecimal value.

Prepared: EZIEAGA

The port number.


The master clock quality level.
Contains a list of MO instances that reserve this MO.

long
long
ManagedObject

Date: 2014-05-27
Sheet: 14.0.2

0..255

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
PacketFrequencySyncRef

serverAddress

RBS DUW

Network Parameters

Specifies the domain or IP address of the server can be either IPv4 or


IPv6.

183 (520)

string

The input format for an IPv4 address is four fields of digits, separated by a
dot. Each field consists of one to three digits.
The input format for an IPv6 address is as defined in specification
RFC4291, chapter 2.2, bullet 1 and 2.
A valid domain name:
- has characters of type letters, numbers and a hyphen "-", where hyphens
can be anywhere in the middle of a name, but cannot be located at the end
or beginning of a name
- cannot have spaces
- is case insensitive
- can include dots for the use of sub domains.
If this MO refers to an IpAccessHostEt MO, the IP address in this attribute
must be of same format as the referenced IpAccessHostEt MO.
Lock before modify: Yes

PacketFrequencySyncRef
PeerIPv4
PeerIPv4
PmService

userLabel
address
peerIPv4Id
maxNoOfCounters

RBS DUW
RBS 6401
RBS 6401
RNC

Label for free use.


IPv4 Peer IP Address.
IPv4 peer name.
The maximum number of simultaneously active counters.

string
string
string
long

1..253
10000..7500000

65000

1700000

If this limit is exceeded, when a performance monitoring is created


or resumed, the create or resume operation is rejected.
If the total number of simultaneously active counters becomes
higher than a preset percentage of the maximum limit, a alarm is issued.
To keep the number of active counters below the limit, performance
monitorings can be suspended if this value is set to a lower value than
before. The most recently defined performance monitorings are suspended
first.

PmService

minorAlarmCeasingDelta

RBS DUW

The percentage of the attribute maxNoOfCounters used to calculate the


minor alarm ceasing limit.

long

1..30

Minor alarm ceasing limit = maxNoOfCounters * (100 minorAlarmCeasingDelta) / 100


A minor alarm is ceased when the total number of active counters becomes
lower than the minor alarm ceasing limit.
The attribute value must confirm to the following rule: The calculated minor
alarm ceasing limit >= the calculated warning alarm ceasing limit.
Unit: 1 %

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
PmService

minorAlarmCeasingDelta

RNC

Network Parameters

The percentage of the attribute maxNoOfCounters used to calculate the


minor alarm ceasing limit.

long

184 (520)
1..30

Minor alarm ceasing limit = maxNoOfCounters * (100 minorAlarmCeasingDelta) / 100


A minor alarm is ceased when the total number of active counters
becomes lower than the minor alarm ceasing limit.
The attribute value must confirm to the following rule: The
calculated minor alarm ceasing limit >= the calculated warning alarm
ceasing limit.
Unit: 1 %
PmService

performanceDataPath

RBS DUW

The name of the path to where the ROP files are stored.

string

PmService

performanceDataPath

RNC

The name of the path to where the ROP files are stored.

string

PmService

performanceDataVolume

RBS DUW

The volume (c, p or any r-volume) where the ROP files are stored. The
string
format for this attribute is: /c/, /pxxxxxx/ or /rxxxxxx/, where each x is a digit
(0..9).

/c/

PmService

performanceDataVolume

RNC

The volume (c, p or any r-volume) where the ROP files are stored. The
string
format for this attribute is: /c/, /pxxxxxx/ or /rxxxxxx/, where each x is a digit
(0..9).

/c/

PmService

PmServiceId

RBS DUW

The value component of the RDN.

PmService

PmServiceId

RNC

/p001200/

string

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


PmService

warningAlarmCeasingDelta

RBS DUW

The percentage of maxNoOfCounters used to calculate the warning alarm long


ceasing limit.

1..20

1..20

Warning alarm ceasing limit = maxNoOfCounters *


(warningAlarmLimitPercent - warningAlarmCeasingDelta)/100.
A warning alarm is ceased when the total number of active counters
becomes lower than the warning alarm ceasing limit.
The attribute value must confirm to the following rules:
The calculated warning alarm ceasing limit <= the calculated minor alarm
ceasing limit.
warningAlarmLimitPercent > warningAlarmCeasingDelta.
Unit: 1 %
PmService

warningAlarmCeasingDelta

RNC

The percentage of maxNoOfCounters used to calculate the warning alarm long


ceasing limit.
Warning alarm ceasing limit = maxNoOfCounters *
(warningAlarmLimitPercent - warningAlarmCeasingDelta)/100.
A warning alarm is ceased when the total number of active counters
becomes lower than the warning alarm ceasing limit.
The attribute value must confirm to the following rules:
The calculated warning alarm ceasing limit <= the calculated minor
alarm ceasing limit.
warningAlarmLimitPercent > warningAlarmCeasingDelta.
Unit: 1 %

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
PmService

warningAlarmLimitPercent

RBS DUW

Network Parameters

The percentage of the attribute maxNoOfCounters used to calculate the


warning alarm limit.

185 (520)

long

0..100

80

80

long

0..100

80

80

Warning alarm limit = maxNoOfCounters * warningAlarmLimitPercent/100


A warning alarm is raised if the total number of active counters exceeeds
the warning alarm limit.
The attribute value must confirm to the following rule:
warningAlarmLimitPercent > warningAlarmCeasingDelta.
Unit: 1 %

PmService

warningAlarmLimitPercent

RNC

The percentage of the attribute maxNoOfCounters used to calculate the


warning alarm limit.
Warning alarm limit = maxNoOfCounters *
warningAlarmLimitPercent/100
A warning alarm is raised if the total number of active counters
exceeeds the warning alarm limit.
The attribute value must confirm to the following rule:
warningAlarmLimitPercent > warningAlarmCeasingDelta.
Unit: 1 %

RadioEquipmentClock

clockState

RBS 6401

Shows the state of equipment clock.

EquipmentClockState

RadioEquipmentClock

equipmentClockPriorityTable

RBS 6401

Shows all equipment clock references in one place._x000D_


_x000D_
Value will be NULL if no equipment clock reference existed.

EquipmentClockReference

RadioEquipmentClock
Ranap

radioEquipmentClockId
availabilityStatus

RBS 6401
RNC

Value component of the RDN.


The availability status of the RANAP.
More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9 or bit 10 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED

string
long

Ranap

cnDomainInd

RNC

Core network domain indicator, as defined in the Ranap specification.


SupportedCoreNetDomains
Specifies whether this instance of Ranap belongs to the CS or PS domain.

FREE_RUN = 1
HOLDOVER = 2
LOCKED = 3
LOCKING = 4

0..2047

CIRCUIT_SWITCHED = 0
PACKET_SWITCHED = 1

Dependencies: It is not possible to create a Ranap instance if cnDomainInd


= CIRCUIT_SWITCHED, userPlaneTransportOption.ipv4 = TRUE for the
parent IuLink, and userPlaneIpResourceRef for the parent IuLink is empty.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ranap

cnId

RNC

Network Parameters

Identity of the Core Network node that this MO instance represents.


long
This identity must be unique within the CnOperator in which this instance is
contained.
When NRI MOCN is active, this identity should be unique within the RNC.

186 (520)
-1..4095

Dependencies: If Iu Flex is active for the domain that this Ranap instance
belongs to (CS or PS as specified in cnDomainInd), cnId must be > -1. If Iu
Flex is not active for the domain, cnId must be == -1.
See the class description of CnOperator for further restrictions.

Ranap

localSccpApRef

RNC

Ranap

maxResetResourceMessageSize

RNC

Ranap

networkResourceIdentifier

RNC

Reference to the SccpApLocal MO that represents the local SCCP Access SccpApLocal
point.
Maximum number of IuSigConn IDs to be sent in each RESET
long
RESOURCE message to the CN.
List of NRI values used by Iu Flex to select a CN node when the routing
long
procedure is based on (P)TMSI .
The first 8 elements of the list are always used by the RNC. When
RncFeature=SupHighCapMscPool is activated, the remaining 24 elements
are also taken into account.
-1 means not defined.

1..250

250

250

-1,-1,-1,-1,-1,-1,-1,1,-1,-1,-1,-1,-1,-1,1,-1,-1,-1,-1,-1,-1,1,-1,-1,-1,-1,-1,-1,1,-1,-1,-1

-1..1023

Sequence length must be in the range 32..32


Feature: SupHighCapMscPool
Ranap

noOfResetSendings

RNC

Number of consecutive retries of sending RESET message to the CN.


An alarm is issued only once and will occur after the last unsuccessful
RESET message, that is, after last timeout of resetResendT.

long

Ranap

operationalState

RNC

The operational state of the RANAP signaling bearer.

SupportedOperStates

Ranap

overloadCtrlEnabled

RNC

Enables or disables the RANAP Overload Control feature for this Iu link.

BooleanVals

0..255

1..64

2..99

DISABLED = 0
ENABLED = 1
FALSE = 0
TRUE = 1

FALSE(0)

Takes effect: Immediately


Feature: RanapOverloadControl
Ranap

overloadCtrlSupervision

RNC

Ranap

overloadCtrlSupervision.msgIntervalTimeMin

RNC

Timers for RANAP Overload Control supervision.

OverloadCtrlSupervisionDef

Feature: RanapOverloadControl
Minimum interval between two consecutive RANAP Overload messages. A long
RANAP Overload message received while this timer is running will be
ignored. Denoted T(igOR) in 3GPP.
Takes effect: Immediately
Unit: s
Ranap

overloadCtrlSupervision.reductionStepHoldTi RNC
me

Maximum time that the RNC shall remain in a certain reduction step after
reception of a RANAP Overload message. Denoted T(inTR) in 3GPP.

long

Takes effect: Immediately


Unit: s
Ranap

Prepared: EZIEAGA

RanapId

RNC

Naming attribute. Contains the value part of the RDN.

Date: 2014-05-27
Sheet: 14.0.2

string

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ranap

ranapResetResourceMonitorPeriod

RNC

Network Parameters

Monitoring period for the number of received Connection-Id's in Ranap


long
"reset-resource" messages.
When the number of Connection-ID's received in RANAP "reset-resource"
messages from this core network node exceeds the value of
ranapResetResourceMonitorThresh within the time interval set by this
attribute, the FM event Ranap_CNInitiatedResetResource is raised.

187 (520)
30..300

60

60

Unit: s
Resolution: 30
Ranap

ranapResetResourceMonitorThresh

RNC

Threshold value for the number of received Connection-Id's in Ranap


long
"reset-resource" messages.
When the number of Connection-ID's received in RANAP "reset-resource"
messages from this core network node exceeds the value of this threshold
within the time interval set by ranapResetResourceMonitorPeriod, the FM
event Ranap_CNInitiatedResetResource is raised.
The value -1 is used to turn off monitoring of RANAP "reset-resource"
messages for this core network node.

-1..-1 1..500

-1 200 (when activated)

Ranap

relativeCapacity

RNC

Relative capacity of this Ranap instance (CN node) compared to other


long
nodes in the domain. Only used when Iu Flex is active.
The capacity weights for all selected Ranap instances (CN nodes) for the
current domain type are added together, to give the sum of capacity
weights. The capacity weight for each instance is then divided by the total
sum, giving the probability that that instance will be selected. When the
probability has been calculated, either a random number or the NRI of a Ue
(depending on the algorithm) is used to select the Ranap instance to use.
Only Ranap instances with relativeCapacity > 0 are considered in the
random selection algorithm.

0..255

50

Ranap

remoteSccpApRef

RNC

Ranap

resetAckGuardT

RNC

Reference to the SccpApRemote MO that represents the remote SCCP


SccpApRemote
Access point.
Guard period in sec. before sending a RESET ACKNOWLEDGE message long
to the CN.
Initially set to 25 sec.

1..120

25

25

If a failure at the CN results in the loss of transaction reference information,


a RESET message is sent to the RNC.
WCDMA RAN uses the RESET message to release the Radio Access
Bearers that are affected and delete all the references for the CN that sent
the RESET message.
The timer starts in the RNC when it receives the RESET message.
The timer always runs until it expires.
When the timer expires the RNC sends a RESET ACKNOWLEDGE
message to the CN indicating that all UEs that were involved in a call are
no longer transmitting and that all references in the WCDMA RAN are
cleared.
Unit: 1 second
Resolution: 1

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Ranap

resetResendT

RNC

Network Parameters

Time in sec. between successive sendings of RESET message to the CN. long

188 (520)
1..120

40

40

0..200

100

100

0..420

100

100

The timer starts when the RNC sends a RESET message to the CN.
The timer stops in any of next two cases:
? The RNC receives the RESET ACKNOWLEDGE message from the CN.
? The RNC receives a RESET message from the CN, when the RNC is
waiting for the RESET ACKNOWLEDGE message. In this case, a RESET
ACKNOWLEDGE message is sent to the CN.
Unit: 1 second
Resolution: 1

Ranap

sccpDisabledT

RNC

Timer for supervising the propagated operational state change of the local long
SCCP.
The alarm 'Local Failure' is issued on timer expiry.
Unit: 1 second
Resolution: 1

Ranap

userLabel

RNC

Ranap

userOutOfServiceT

RNC

Provides the possibility to put a user-friendly label on the MO instance.


The value is not used by the RNC.
Timer for supervising the N-STATE-indication for the remote SCCP
(SSN=1) or the remote RANAP (SSN=142).

string
long

Timer expiry for remote SCCP (SSN=1) issues the alarm 'Local Failure' and
for remote RANAP (SSN=142) issues the alarm 'Remote Failure'.
Unit: 1 second
Resolution: 1
RncFunction

intraNodeIpResourceRef

RNC

Node internal IP resources available for inter-subrack data transport. The IpAccessHostPool
node internal IP resources are used to relieve the inter-subrack links (ISL)
of dedicated channel data transport. The IpAccessHostPool referred to by
this attribute must contain at least one IpAccessHostEt from each subrack.
Only applicable for RNC nodes with Ethernet inter-subrack links. When set
to a valid reference, the BEES (Backend Ethernet Switching) function is
activated.

RncFunction

nbapAuditInterval

RNC

Time interval for periodic NBAP audit procedure.

long

0..24

long

0..63

Special values:
0 means that the periodic NBAP audit is deactivated.
If the periodic NBAP audit is activated by changing the value from zero
(deactivated) to non zero (activated), the NBAP audit will start immediately,
and then wait the configured time interval. A change from a non zero to
another non zero value will cause a reset of the timer, without an NBAP
audit.
Unit: hour
RncFunction

nbapDscp

RNC

DiffServ code point value sent by RNC for NBAP-C and NBAP-D.
Takes effect: For all Iub links at cold RNC node restart. It will not be
affected by warm or refresh restart.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Rnsap

availabilityStatus

RNC

The availability status of the RNSAP.


More than one of the following conditions can apply for the same object:
Bit 0 = 1: INTEST
Bit 1 = 1: FAILED
Bit 2 = 1: POWEROFF
Bit 3 = 1: OFFLINE
Bit 4 = 1: OFFDUTY
Bit 5 = 1: DEPENDENCY (set to 1 when bit 9 or bit 10 is set to 1)
Bit 6 = 1: DEGRADED
Bit 7 = 1: NOTINSTALLED
Bit 8 = 1: LOGFULL
Bit 9 = 1: DEPENDENCYLOCKED
Bit 10 = 1: DEPENDENCYFAILED

long

Rnsap

localSccpApRef

RNC

Rnsap

operationalState

RNC

Reference to the SccpApLocal MO that represents the local SCCP Access SccpApLocal
point.
The operational state of the RNSAP signaling bearer.
SupportedOperStates

Rnsap

remoteSccpApRef

RNC

Rnsap
Rnsap

RnsapId
sccpDisabledT

RNC
RNC

Reference to the SccpApRemote MO that represents the remote SCCP


SccpApRemote
Access point.
Naming attribute. Contains the value part of the RDN.
string
Timer for supervising the propagated operational state change of the local long
SCCP.

189 (520)
0..2047

DISABLED = 0
ENABLED = 1

0..200

100

100

0..200

100

100

The alarm 'Local Failure' is issued on timer expiry.


Unit: 1 second
Resolution: 1
Rnsap

userLabel

RNC

Rnsap

userOutOfServiceT

RNC

Provides the possibility to put a user-friendly label on the MO instance.


The value is not used by the RNC.
Timer for supervising the N-STATE-indication for the remote SCCP
(SSN=1) or the remote RNSAP (SSN=143).

string
long

Timer expiry for remote SCCP (SSN=1) issues the alarm 'Local Failure' and
for remote RNSAP (SSN=143) issues the alarm 'Remote Failure'.
Unit: 1 second
Resolution: 1
RouteTableIPv4Static
SccpApLocal

routeTableIPv4StaticId
availabilityStatus

RBS 6401
RNC

Value component of the RDN for IPv4StaticRouteTable.


The availability status.
It contains details about operationalState.
Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
Possible values for operational state DISABLED:
- FAILED: the AP is not handled by any SCCP instance.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

string
AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SccpApLocal

enablePoolProxyExtension

RNC

Network Parameters

190 (520)

Controls adding of OPC to Calling Party Address, DPC to Called Party


boolean
Address from routing label and copying SSN from Called Party Address to
Calling Party Address if absent.

false = Do not add OPC to Calling Party Address, DPC to Called


Party Address and do not copy SSN from Called Party Address to Calling
Party Address.
true = Add OPC to Calling Party Address, DPC to Called Party
Address and copy SSN from Called Party Address to Calling Party
Address.
Disturbances: At a change of this attribute, the SCCP user traffic for
the other SccpApLocal related to the same SccpSp is affected.

SccpApLocal

maxConn

RNC

Specifies the maximum number of connections per SCCP instance allowed long
for this SCCP Access Point. It is only valid for local SCCP Access Points.

1..524288

The maximum value on the HD stack is 32768. On the HD stack the


sum of the maxConn for all SccpApLocal related to the same SccpSp
should be less than or equal to 32768. The total number of connections
handled by the HD stack can be increased by adding SCCP instances.
On the MONO stack the sum of the maxConn for all SccpApLocal
related to the same SccpSp should be less than or equal to 400000.

SccpApLocal

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the AP is handled by at least


one SCCP instance.
SccpApLocal

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

SccpApLocal

SccpApLocalId

RNC

The value component of the RDN.

string

SccpApLocal

ssN

RNC

The Subsystem number (SSN) of the SCCP Access Point.

long

3..254

See CPI

The SSN has to be unique among all other SccpApLocal MOs


under the same SccpSp MO.
SccpApLocal

userLabel

RNC

Label for free use.

string

SccpApLocal

useS1

RNC

Controls adding of OPC from routing label to Calling Party Address if


absent.

boolean

0 TRUE(1)

false = Do not add OPC to Calling Party Address.


true = Add OPC to Calling Party Address.
SccpApRemote

availabilityStatus

RNC

The availability status.

AvailabilityStatus

It contains details about operationalState.


Possible values for operational state ENABLED:
- NO_STATUS: the MO is fully operable.
- DEGRADED: congestion is detected.
Possible values for operational state DISABLED:
- FAILED: the MO is not operable.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

SccpApRemote

mtp3bApId

RNC

The identity of the Mtp3bAp used by this MO.

Mtp3bAp

SccpApRemote

operationalState

RNC

The operational state.

OperState

191 (520)

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if an SSA indication was


received.
The operational state is DISABLED initially or if an SSP indication
was received.
SccpApRemote

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

SccpApRemote

SccpApRemoteId

RNC

The value component of the RDN.

string

SccpApRemote

ssN

RNC

The Subsystem Number (SSN) of the SCCP Access Point.

long

2..254

See CPI

The SSN must be unique among all SccpApRemote instances


referring to the same Mtp3bAp.
SccpApRemote

userLabel

RNC

Label for free use.

string

SccpScrc

SccpScrcId

RNC

The value component of the RDN.

string

SccpScrc

userLabel

RNC

Label for free use.

string

SccpSp

hopCounterSclc

RNC

The SCLC hop counter is a parameter that is decremented for each


performed GT translation for SCLC messages on the way to the end
destination.

long

1..15

long

1..15

0..100

50

50

If decrementing the counter results in the value of zero in a non-end


destination node, the SCCP initiates the appropriate error procedure.

SccpSp

hopCounterScoc

RNC

The SCOC hop counter is a parameter that is decremented for each


performed GT translation for SCOC messages on the way to the end
destination.
If decrementing the counter results in the value of zero in no end
destination node, the SCCP initiates the appropriate error procedure.

SccpSp

lowerConnThres

RNC

Allows the user to specify the level at which the lower connection threshold long
notification is triggered. The thresholds must be given as a percentage of
the maximum number of connection resources made available for the
entire SCCP.
Unit: 1 %
Dependencies: The value of this attribute must be lower than or
equal to the value for attribute upperConnThres.

SccpSp

mtp3bSpId

RNC

The identity of the L3 Signalling Point used by this MO.

ManagedObject

SccpSp

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED, if the SP is handled by at least


one SCCP instance.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SccpSp

prioGeneral

RNC

Network Parameters

Sets the priority for all the other messages which are issued by the SCCP
itself.

192 (520)

long

0..3

long

0..3

long

0..3

long

0..3

When a message is transferred from the SCCP, the message


priority uses the two spare bits in the SIO.
Coding of the message priority:
0 Lowest priority
1
2
3 Highest priority

SccpSp

prioIT

RNC

Sets the priority for the Inactivity Test message when issued by the SCCP
itself.
When a message is transferred from the SCCP, the message
priority uses the two spare bits in the SIO.
Coding of the message priority:
0 Lowest priority
1
2
3 Highest priority

SccpSp

prioRLSD

RNC

Sets the priority for the connection release message when issued by the
SCCP itself.
When a message is transferred from the SCCP, the message
priority uses the two spare bits in the SIO.
Coding of the message priority:
0 Lowest priority
1
2
3 Highest priority

SccpSp

prioSST

RNC

Sets the priority for the Subsystem Test message when issued by the
SCCP itself.
When a message is transferred from the SCCP the message
priority uses the two spare bits in the SIO.
Coding of the message priority:
0 Lowest priority
1
2
3 Highest priority

SccpSp

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

SccpSp

SccpSpId

RNC

The value component of the RDN.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SccpSp

smiValue

RNC

The Subsystem Multiplicity Indicator (SMI) is always ignored for incoming


messages. This SCCP can however be configured to insert a specific SMI
value in outgoing messages. The coding and interpretation is as follows:
Coding
0
|
1
|
2
|
3
|

SccpSp

swapUDTPointer

RNC

Network Parameters

193 (520)

long

0..3

long

0..1

long

1..65535

300

10

long

1..65535

600

600

long

1..65535

150

150

long

1..65535

6600

6600

long

1..65535

3000

3000

Comment
Affected Subsystem multiplicity unknown.
Affected Subsystem is solitary.
Affected Subsystem is duplicated.
Spare.

There are two ways to construct a UDTS from a UDT:


- to only swap the pointers to Called Party Address (CdPA) and
Calling Party Address (CgPA) in a UDT message when constructing a
UDTS.
- to swap data
How this is done in the SCCP is configurable.
The XUDTS is constructed in the same way.
The coding and interpretation is as follows:
0 = swap data - CdPA is sent before CgPA
1 = swap pointers - CdPA is sent after CgPA.

SccpSp

tCong

RNC

Congestion timer.
Guiding values:
Range 10-2550
Default 300
Unit: 1 ds (0.1 s)

SccpSp

tconnEst

RNC

Connection establishment control timer.


Guiding values:
Range 600 - 1200
Default 600
Unit: 1 ds (0.1 s)

SccpSp

tconnResp

RNC

Connection response waiting timer.


Guiding values:
Range 100-200
Default 150
Unit: 1 ds (0.1 s)

SccpSp

tIar

RNC

Receive inactivity control timer.


Guiding values:
Range 6600-12600
Default 6600
Unit: 1 ds (0.1 s)

SccpSp

tIas

RNC

Send inactivity control timer.


Guiding values:
Range 3000-6000
Default 3000
Unit: 1 ds (0.1 s)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SccpSp

tReass

RNC

Reassembly timer.

Network Parameters

194 (520)

long

1..65535

150

150

long

1..65535

100

100

long

1..65535

300

300

80

80

long

long

long

Guiding values:
Range 100-200
Default 150
Unit: 1 ds (0.1 s)
SccpSp

tRel

RNC

Connection release timer.


Guiding values:
Range 100-200
Default 100
Unit: 1 ds (0.1 s)

SccpSp

tStatInfo

RNC

Subsystem Status Test timer.


Guiding values:
Range 10-2550
Default 300
Unit: 1 ds (0.1 s)

SccpSp

upperConnThres

RNC

Allows the user to specify the level at which the upper connection threshold long
notification is triggered. The thresholds must be given as a percentage of
the maximum number of connection resources made available for the
entire SCCP.

SccpSp

userLabel

RNC

Label for free use.

string

SccpSp

useSCMG

RNC

The use of SCMG functions.

Scmg

0..100

Unit: 1 %

SST = SCCP Subsystem Test message.


SSA = SCCP Subsystem Allowed message.
SSP = SCCP Subsystem Prohibited message.
SSC = SCCP Subsystem Congested message.
SccpSp

useSCMG.allowRemoteBroadcast

RNC

Controls the remote broadcast.


0 = allow remote broadcast.
1 = do not allow remote broadcast.
Set allowRemoteBroadcast=1 for the TTC standard.

SccpSp

useSCMG.initiateTimerTcon

RNC

Controls whether to initiate hardcoded congestion timer or not.


0 = start timer when SSC is received.
1 = do not start timer.
Set initiateTimerTcon=1 for the TTC standard.

SccpSp

useSCMG.sendSSA

RNC

Controls when to send SSA (SCCP Subsystem Allowed message).


0 = Do not send SSA.
1 = Send SSA immediately when client attaches.
Set sendSSA=0 for the TTC standard.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SccpSp

useSCMG.sendSSP

RNC

Network Parameters

Controls whether to send SSP (SCCP Subsystem Prohibited message).

195 (520)

long

long

long

0 = Do not send SSP when client detaches.


1 = Send SSP immediately when client detaches.
2 = Do not send SSP when receiving MTP_TRANSFER_ind and
user is detached and do not send when user detaches.
3 = Send SSP when receiving MTP_TRANSFER_ind and client is
detached and send when user detaches.
Set sendSSP=2 for the TTC standard.

SccpSp

useSCMG.sendSST

RNC

Controls when to send SST (SCCP Subsystem Test message).


0 = Wait for tStatInfo timer to expire once after MTP_RESUME
before sending SST.
1 = Send SST immediately after MTP_RESUME, then start
tStatInfo timer.
Set sendSST=0 for the TTC standard.

SccpSp

useSCMG.useSST

RNC

Controls whether to send SST messages or not (SCCP Subsystem Test


message).
0 = Send SST as indicated by sendSST.
1 = (not used)
2 = (not used)
3 = Do not initiate SST.
Set useSST=3 for the TTC standard

Sctp

allowedIncrementCookieLife

RBS DUW

The attribute defines the allowed increment of the validCookieLife


parameter (in local node) when an increase of the parameter is requested
from remote node.

long

0..180

30

30

long

0..180

30

30

A new value of the attribute does not apply to associations that are already
established.
Unit: 1 s
Sctp

allowedIncrementCookieLife

RNC

The attribute defines the allowed increment of the validCookieLife


parameter (in local node) when an increase of the parameter is requested
from remote node.
A new value of the attribute does not apply to associations that are
already established.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

associationMaxRtx

RBS DUW

Network Parameters

The maximum number of consecutive retransmissions to a remote peer (on long


all the remote transport addresses of the peer).
If the number of retransmissions becomes greater than this value, the
remote peer is considered to be unreachable and the association is closed
down.

196 (520)
1..20

1..20

8 Iu, Iur: 8
Iub: 12

12

Set the value of this attribute within the following limits:


- If the selection algorithm is set to SCTP_PATHS: pathMaxRtx <=
associationMaxRtx <= number of remote transport addresses *
pathMaxRtx,
- If the selection algorithm is set to IP_PATHS: pathMaxRtx <=
associationMaxRtx <= number of IP paths * pathMaxRtx.
The value might need to be increased to avoid frequently lost associations
in an unstable network.
A new value of this attribute applies to both existing and new associations
that do not use any SctpProfile MO.
Unit: 1 attempts

Sctp

associationMaxRtx

RNC

The maximum number of consecutive retransmissions to a remote peer (on long


all the remote transport addresses of the peer).
If the number of retransmissions becomes greater than this value,
the remote peer is considered to be unreachable and the association is
closed down.
Set the value of this attribute within the following limits:
- If the selection algorithm is set to SCTP_PATHS: pathMaxRtx <=
associationMaxRtx <= number of remote transport addresses *
pathMaxRtx,
- If the selection algorithm is set to IP_PATHS: pathMaxRtx <=
associationMaxRtx <= number of IP paths * pathMaxRtx.
The value might need to be increased to avoid frequently lost
associations in an unstable network.
A new value of this attribute applies to both existing and new
associations that do not use any SctpProfile MO.
Unit: 1 attempts

Sctp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

availabilityStatus

RNC

Network Parameters

The availability status.

197 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

BundlingActivated

DISABLED = 0
ENABLED = 1

ENABLED(1)

ENABLED(1)

BundlingActivated

DISABLED = 0
ENABLED = 1

ENABLED(1)

ENABLED(1)

It contains details about operationalState.

Sctp

bundlingActivated

RBS DUW

Enables and disables the use of bundling for DATA chunks.


A new value of this attribute applies to both existing and new associations.

Sctp

bundlingActivated

RNC

Enables and disables the use of bundling.


A new value of this attribute applies to both existing and new
associations.

Sctp

bundlingTimer

RBS DUW

Specifies the maximum SCTP bundling delay for DATA chunks.

long

0..1000

10

10

long

0..1000

10

10

The amount of time added to the RTO of a specific address when setting long
up the period of time between sending heartbeats. Small values can lead to
an earlier detection of unreachable addresses than higher values.
However, sending the heartbeat too often can lead to a performance
penalty.

1..1800

30

Value=0 means that SCTP bundles only what is available and sends
directly (no delay).
A new value of the attribute does not change the current measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new associations.
Unit: 1 ms (millisecond)

Sctp

bundlingTimer

RNC

Specifies the maximum SCTP bundling delay.


Value=0 means that SCTP bundles only what is available and
sends directly (no delay).
A new value of the attribute does not change the current
measurement interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 ms (millisecond)

Sctp

heartbeatInterval

RBS DUW

A new value of the attribute does not change the current measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new associations.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

heartbeatInterval

RNC

Network Parameters

The amount of time added to the RTO of a specific address when setting long
up the period of time between sending heartbeats. Small values can lead to
an earlier detection of unreachable addresses than higher values.
However, sending the heartbeat too often can lead to a performance
penalty.

198 (520)
1..1800

30 Iu, Iur: 30
Iub: 1

A new value of the attribute does not change the current


measurement interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 s
Sctp

heartbeatMaxBurst

RBS DUW

The maximum number of heartbeats, which can be sent at the same time
during the path probing procedure. If the value is set to 0, path probing is
not used.

long

0..4

long

0..4

long

1..180000

500

70

long

1..180000

500 Iu, Iur: 500


Iub: 70

A new value of the attribute does not apply to associations that are already
established.
Sctp

heartbeatMaxBurst

RNC

The maximum number of heartbeats, which can be sent at the same time
during the path probing procedure. If the value is set to 0, path probing is
not used.
A new value of the attribute does not apply to associations that are
already established.

Sctp

heartbeatPathProbingInterval

RBS DUW

The interval between consecutive heartbeats during the path probing.


The value of this attribute has the following relationship to the values of
other attributes:
maximumRto <= heartbeatPathProbingInterval <= heartbeatInterval.
A new value of the attribute applies to both existing and new associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

heartbeatPathProbingInterval

RNC

The interval between consecutive heartbeats during the path probing.


The value of this attribute has the following relationship to the
values of other attributes:
maximumRto <= heartbeatPathProbingInterval <=
heartbeatInterval.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

heartbeatStatus

RBS DUW

Enables and disables heartbeats for associations.

boolean

1 TRUE(1)

boolean

TRUE(1)

true - enable heartbeats.


false - disable heartbeats.
A new value of this attribute applies to both existing and new associations.
Sctp

heartbeatStatus

RNC

Enables and disables heartbeats for associations.


true - enable heartbeats.
false - disable heartbeats.
A new value of this attribute applies to both existing and new
associations.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

initialAdRecWin

RBS DUW

Network Parameters

The initial value of the advertised receiver window credit.

199 (520)

long

1500..1048576

32768

16384

long

1500..1048576

32768 Iu, Iur: 32768


Iub: 16384

long

1..12000

20

20

long

1..12000

20

20

1..6500

3600

3600

1..6500

3600

3600

If the value of this attribute is increased, it applies to both existing and new
associations. If the value is decreased, it does not apply to associations
that are already established.
Unit: 1 B
Sctp

initialAdRecWin

RNC

The initial value of the advertised receiver window credit.


If the value of this attribute is increased, it applies to both existing
and new associations. If the value is decreased, it does not apply to
associations that are already established.
Unit: 1 B

Sctp

initialRto

RBS DUW

The initial value that the Retransmission Timeout (RTO) takes prior to the
first measurement of the Round-Trip Time (RTT).
The value of this attribute has the following relationship to the values of
other attributes:
minimumRto <= initialRto <= maximumRto
A new value of the attribute does not apply to associations that are already
established.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

initialRto

RNC

The initial value that the Retransmission Timeout (RTO) takes prior to the
first measurement of the Round-Trip Time (RTT).
The value of this attribute has the following relationship to the
values of other attributes:
minimumRto <= initialRto <= maximumRto
A new value of the attribute does not apply to associations that are
already established.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

intervalOobPkts

RBS DUW

The number of seconds after which the counter for out-of-the-blue packets long
is reset.
A new value of the attribute does not change the current measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new associations.
Unit: 1 s

Sctp

intervalOobPkts

RNC

The number of seconds after which the counter for out-of-the-blue packets long
is reset.
A new value of the attribute does not change the current
measurement interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 s

Sctp

ipAccessHostGpbId

RBS DUW

Reference to an instance of an IpAccessHostGpb MO.

IpAccessHostGpb

Dependencies: Setting of this attribute is rejected if ipAccessSctpRef is set.


Sctp

ipAccessHostGpbId

RNC

Reference to an instance of an IpAccessHostGpb MO.

IpAccessHostGpb

Dependencies: Setting of this attribute is rejected if


ipAccessSctpRef is set.
Sctp

Prepared: EZIEAGA

ipAccessSctpRef

RBS DUW

Reference to an instance of an IpAccessSctp MO.


Dependencies: Setting of this attribute is rejected if ipAccessHostGpbId is
set.

Date: 2014-05-27
Sheet: 14.0.2

IpAccessSctp

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

200 (520)

Sctp

ipAccessSctpRef

RNC

Reference to an instance of an IpAccessSctp MO.


Dependencies: Setting of this attribute is rejected if
ipAccessHostGpbId is set.

IpAccessSctp

Sctp

keyChangePeriod

RBS DUW

Defines how often the secret key used for computing the Message
Authentication Code (MAC) on the State Cookie is changed.

long

1..180

long

1..180

long

1..16384

long

1..16384

long

1..12000

40

40

long

1..12000

40

40

long

1..16384

17

17

long

1..16384

17

17

A new value of the attribute does not change the current measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new associations.
Unit: 1 s
Sctp

keyChangePeriod

RNC

Defines how often the secret key used for computing the Message
Authentication Code (MAC) on the State Cookie is changed.
A new value of the attribute does not change the current
measurement interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 s

Sctp

maxBurst

RBS DUW

The number of packages that are sent during the fast retransmit phase
when a SACK is processed.
A new value of the attribute applies to both existing and new associations.

Sctp

maxBurst

RNC

The number of packages that are sent during the fast retransmit phase
when a SACK is processed.
A new value of the attribute applies to both existing and new
associations.

Sctp

maximumRto

RBS DUW

The maximum value for the RTO.


The value of this attribute must be greater than the value of minimumRto.
A new value of the attribute applies to both existing and new associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

maximumRto

RNC

The maximum value for the RTO.


The value of this attribute must be greater than the value of
minimumRto.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

maxIncomingStream

RBS DUW

The allowed maximum number of incoming streams for an association.


A change to this attribute does not affect the existing associations. To apply
a new value, the endpoint must be re-created.

Sctp

maxIncomingStream

RNC

The allowed maximum number of incoming streams for an association.


A change to this attribute does not affect the existing associations.
To apply a new value, the endpoint must be re-created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

maxInitialRtrAtt

RBS DUW

Network Parameters

The maximum number of retransmissions allowed for both INIT and


long
COOKIE_ECHO chunks. If the number of retransmissions exceeds this
value, SCTP aborts the initialization of the association and reports the error
to the SCTP user.

201 (520)
1..16

1..16

A new value of the attribute does not apply to associations that are already
established.
Unit: 1 attempts
Sctp

maxInitialRtrAtt

RNC

The maximum number of retransmissions allowed for both INIT and


long
COOKIE_ECHO chunks. If the number of retransmissions exceeds this
value, SCTP aborts the initialization of the association and reports the error
to the SCTP user.
A new value of the attribute does not apply to associations that are
already established.
Unit: 1 attempts

Sctp

maxOutgoingStream

RBS DUW

The allowed maximum number of outgoing streams for an association.

long

1..16384

17

17

long

1..16384

17

17

1..20

1..20

A change to this attribute does not affect the existing associations. To apply
a new value, the endpoint must be re-created.
Sctp

maxOutgoingStream

RNC

The allowed maximum number of outgoing streams for an association.


A change to this attribute does not affect the existing associations.
To apply a new value, the endpoint must be re-created.

Sctp

maxShutDownRtrAtt

RBS DUW

The maximum number of retransmissions during the shutdown phase of an long


association.
A new value of the attribute applies to both existing and new associations.
Unit: 1 attempts

Sctp

maxShutDownRtrAtt

RNC

The maximum number of retransmissions during the shutdown phase of an long


association.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 attempts

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

maxUserDataSize

RBS DUW

Network Parameters

The maximum number of bytes of an IP datagram that can be transferred


in a single unit over a specific path in an IP network. If an IP datagram
exceeds the Path Maximum Transfer Unit (PMTU), it is either fragmented
or dropped.

long

202 (520)
508..1480

1480

For Sctp that uses IPv6 addresses, the minimum value of this attribute is
1240.
This value does not include the IP header, 20 bytes for IPv4 or 40 bytes for
IPv6.
For Sctp that uses IPv4 addresses, the recommended value of this
attribute is 1480.
For Sctp that uses IPv6 addresses, the recommended value of this
attribute is 1460.
If IPsec is used, the value of this attribute must be less than the
recommended value to make room for the overhead specified by IPsec
protocol to prevent message fragmentation on IP level.
To avoid fragmentation of the SCTP data by the local IPv4 stack, SCTP
aligns the actual used maxUserDataSize with the mtu attribute of the used
IpInterface / FastEthernet MO(s).
SCTP calculates the actual used maxUserDataSize value in the following
way: max { min {maxUserDataSize, mtu - ipHeaderSize}, 508 }, where
ipHeaderSize is 20 octets.
For a multi-homed SCTP endpoint, the minimum value of the mtu attribute
from both IpInterface / FastEthernet MOs is used in calculation.
If the value of the mtu attribute of the used FastEthernet MO is less than
532 octets, then fragmentation of the SCTP data by the local IPv4 stack
can not be avoided.
To avoid fragmentation of the SCTP data by the local IPv6 stack, the value
of this attribute shall have the following relationship to the values of the mtu
attribute of the Ipv6Interface MO:
maxUserDataSize <= mtu - ipHeaderSize, where ipHeaderSize is 40 octets

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

maxUserDataSize

RNC

Network Parameters

The maximum number of bytes of an IP datagram that can be transferred


in a single unit over a specific path in an IP network. If an IP datagram
exceeds the Path Maximum Transfer Unit (PMTU), it is either fragmented
or dropped.

long

203 (520)
508..1480

1480

For Sctp that uses IPv6 addresses, the minimum value of this
attribute is 1240.
This value does not include the IP header, 20 bytes for IPv4 or 40
bytes for IPv6.
For Sctp that uses IPv4 addresses, the recommended value of this
attribute is 1480.
For Sctp that uses IPv6 addresses, the recommended value of this
attribute is 1460.
If IPsec is used, the value of this attribute must be less than the
recommended value to make room for the overhead specified by IPsec
protocol to prevent message fragmentation on IP level.
To avoid fragmentation of the SCTP data by the local IPv4 stack,
SCTP aligns the actual used maxUserDataSize with the mtu attribute of the
used IpInterface / FastEthernet MO(s).
SCTP calculates the actual used maxUserDataSize value in the
following way: max { min {maxUserDataSize, mtu - ipHeaderSize}, 508 },
where ipHeaderSize is 20 octets.
For a multi-homed SCTP endpoint, the minimum value of the mtu
attribute from both IpInterface / FastEthernet MOs is used in calculation.
If the value of the mtu attribute of the used FastEthernet MO is less
than 532 octets, then fragmentation of the SCTP data by the local IPv4
stack can not be avoided.

Sctp

mBuffer

RBS DUW

To avoid fragmentation of the SCTP data by the local IPv6 stack,


the value of this attribute shall have the following relationship to the values
of the mtu attribute of the Ipv6Interface MO:
maxUserDataSize <= mtu - ipHeaderSize, where ipHeaderSize is
40 octets
The
attribute sets the size of the buffer used for storing user data pending long
to be sent or retransmitted in an association. That is, the attribute sets the
maximum amount of user data that SCTP buffers before discarding user
messages.

1..2048

256

1..2048

256 Iu, Iur: 256


Iub: 16

16

The value may need to be increased to ensure stable data flow at high
load.
It must be greater than the value of nThreshold
A new value of this attribute applies to both existing and new associations.
Unit: 1 KB

Sctp

mBuffer

RNC

The attribute sets the size of the buffer used for storing user data pending
to be sent or retransmitted in an association. That is, the attribute sets the
maximum amount of user data that SCTP buffers before discarding user
messages.

long

The value may need to be increased to ensure stable data flow at


high load.
It must be greater than the value of nThreshold
A new value of this attribute applies to both existing and new
associations.
Unit: 1 KB

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

minimumRto

RBS DUW

Network Parameters

The minimum value for RTO.

204 (520)

long

1..500

10

10

long

1..500

10

10

long

1..100

85

85

long

1..100

85

85

1..2048

192

12

The value of this attribute has the following relationship to the values of
other attributes:
tSack + expected Round Trip Time < minimumRto < maximumRto
A new value of the attribute applies to both existing and new associations.
Unit: 1 cs (centisecond, that is 0.01 second)
Sctp

minimumRto

RNC

The minimum value for RTO.


The value of this attribute has the following relationship to the
values of other attributes:
tSack + expected Round Trip Time < minimumRto < maximumRto
A new value of the attribute applies to both existing and new
associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

nPercentage

RBS DUW

This attribute is set as a percentage of the attribute nThreshold. A


congestion-ceased indication is sent to the SCTP user when the usage of
the SCTP send buffer drops below nPercentage.
A new value of the attribute applies to both existing and new associations.
Unit: 1 %

Sctp

nPercentage

RNC

This attribute is set as a percentage of the attribute nThreshold. A


congestion-ceased indication is sent to the SCTP user when the usage of
the SCTP send buffer drops below nPercentage.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 %

Sctp

nThreshold

RBS DUW

Sets the value of the threshold used to ask the SCTP user to stop the
long
delivery of a data on an association. A congestion indication will be sent to
the user when the SCTP send buffer usage is above nTreshold.
The value of this attribute has the following relationship to the value of
mBuffer:
- nThreshold must be less than mBuffer,
- nThreshold = 3/4 * mBuffer, is the normal value.
The value may need to be increased to ensure stable dataflow at high load.
A new value of this attribute applies to both existing and new associations.
Unit: 1 kilobyte

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

nThreshold

RNC

Network Parameters

Sets the value of the threshold used to ask the SCTP user to stop the
long
delivery of a data on an association. A congestion indication will be sent to
the user when the SCTP send buffer usage is above nTreshold.

205 (520)
1..2048

192 Iu, Iur: 192


Iub: 12

The value of this attribute has the following relationship to the value
of mBuffer:
- nThreshold must be less than mBuffer,
- nThreshold = 3/4 * mBuffer, is the normal value.
The value may need to be increased to ensure stable dataflow at
high load.
A new value of this attribute applies to both existing and new
associations.
Unit: 1 kilobyte
Sctp

numberOfAssociations

RBS DUW

long

1..512

long

1..512

RBS DUW

The maximum number of associations that can be handled by this SCTP


MO.
The maximum number of associations that can be handled by this SCTP
MO.
The operational state.

Sctp

numberOfAssociations

RNC

Sctp

operationalState

Sctp

operationalState

RNC

The operational state.

OperState

Sctp

pathMaxRtx

RBS DUW

If the path selection algorithm is SCTP_PATHS, this attribute specifies the


maximum number of consecutive retransmissions to a remote transport
address. For other path selection algorithms, this attribute specifies the
maximum number of consecutive retransmissions over an IP path.

long

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
1..20

If the number of retransmissions becomes greater than this value, the


remote transport address or the IP path is considered to be "inactive" and
no data is sent to it. If all the remote transport addresses or all IP paths
become "inactive", the association will be closed down.
The value of this attribute has the following relationships to the values of
other attributes:
- one attempt <= pathMaxRtx <= associationMaxRtx
- pathMaxRtx >= potentiallyFailedMaxRtx
Adapt the value to the network quality. A low value reduces the time for
fault detection, but it is recommended only for stable networks.
The value might need to be increased to avoid frequently lost associations
in an unstable network.
If multi-homed SCTP is used and when tests for insertion and removal of
the Ethernet cable are performed, wait 60 seconds between inserting the
first cable and removing the second cable. That is: remove cable, insert
cable, wait 60 seconds, remove second cable, insert second cable.
A new value of this attribute applies to both existing and new associations
that do not use any SctpProfile MO.
The recommended value for pathMaxRtx is as follows:
- If the selection algorithm is set to SCTP_PATHS, set the value to
associationMaxRtx / number of remote transport addresses.
- If the selection algorithm is set to IP_PATHS, set the value to
associationMaxRtx / number of IP paths.
Unit: 1 attempts

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

pathMaxRtx

RNC

Network Parameters

If the path selection algorithm is SCTP_PATHS, this attribute specifies the


maximum number of consecutive retransmissions to a remote transport
address. For other path selection algorithms, this attribute specifies the
maximum number of consecutive retransmissions over an IP path.

long

206 (520)
1..20

4 Iu, Iur: 4
Iub: 12

If the number of retransmissions becomes greater than this value,


the remote transport address or the IP path is considered to be "inactive"
and no data is sent to it. If all the remote transport addresses or all IP paths
become "inactive", the association will be closed down.
The value of this attribute has the following relationships to the
values of other attributes:
- one attempt <= pathMaxRtx <= associationMaxRtx
- pathMaxRtx >= potentiallyFailedMaxRtx
Adapt the value to the network quality. A low value reduces the time
for fault detection, but it is recommended only for stable networks.
The value might need to be increased to avoid frequently lost
associations in an unstable network.
If multi-homed SCTP is used and when tests for insertion and
removal of the Ethernet cable are performed, wait 60 seconds between
inserting the first cable and removing the second cable. That is: remove
cable, insert cable, wait 60 seconds, remove second cable, insert second
cable.
A new value of this attribute applies to both existing and new
associations that do not use any SctpProfile MO.
The recommended value for pathMaxRtx is as follows:
- If the selection algorithm is set to SCTP_PATHS, set the value to
associationMaxRtx / number of remote transport addresses.
- If the selection algorithm is set to IP_PATHS, set the value to
associationMaxRtx / number of IP paths.
Unit: 1 attempts
The type of path selection algorithm.
PathSelectionType
If switchbackMode has the value NO_SWITCHBACK, pathSelection can
only be set to IP_PATHS. If pathSelection has the value IP_PATHS,
switchbackMode can be set to any value.

Sctp

pathSelection

RBS DUW

Sctp

pathSelection

RNC

The type of path selection algorithm.

Sctp

potentiallyFailedMaxRtx

RBS DUW

This attribute specifies the maximum number of consecutive


long
retransmissions over the IP path that is used for data transmission, before
this path is considered likely to fail.

PathSelectionType

0..20

SCTP_PATHS = 0
IP_PATHS = 1
IP_PATHS_OPTIMIZED = 2

IP_PATHS(1)

SCTP_PATHS(0)

SCTP_PATHS = 0
IP_PATHS = 1
IP_PATHS_OPTIMIZED = 2

IP_PATHS(1)

SCTP_PATHS(0)

If the number of retransmissions becomes greater than this value, the path
used for data transmission is changed.
The value of this attribute has the following relationship to the value of
pathMaxRtx: potentiallyFailedMaxRtx <= pathMaxRtx.
Applicable for the IP_PATHS selection scheme only.
A new value of the attribute applies to both existing and new associations
that do not use any SctpProfile MO.
Unit: 1 attempts

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

potentiallyFailedMaxRtx

RNC

Network Parameters

This attribute specifies the maximum number of consecutive


long
retransmissions over the IP path that is used for data transmission, before
this path is considered likely to fail.

207 (520)
0..20

long

1..4

long

1..4

If the number of retransmissions becomes greater than this value,


the path used for data transmission is changed.
The value of this attribute has the following relationship to the value
of pathMaxRtx: potentiallyFailedMaxRtx <= pathMaxRtx.
Applicable for the IP_PATHS selection scheme only.
A new value of the attribute applies to both existing and new
associations that do not use any SctpProfile MO.
Unit: 1 attempts
Sctp
Sctp
Sctp

reservedBy
reservedBy
rpuId

RBS DUW
RNC
RBS DUW

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.
Reference to an instance of ReliableProgramUniter MO.

ManagedObject
ManagedObject
ReliableProgramUniter

There is a one to one relation between Sctp MO and


ReliableProgramUniter MO instances.
Sctp

rpuId

RNC

Reference to an instance of ReliableProgramUniter MO.

ReliableProgramUniter

There is a one to one relation between Sctp MO and


ReliableProgramUniter MO instances.
Sctp

rtoAlphaIndex

RBS DUW

The attribute rtoAlphaIndex (Retransmission Timeout Alpha Index)


computes the value of the Smoothed Round-Trip Time (SRTT) for a
specific destination address. It weights the RTT values.
The value of this attribute is used to create a value of RTO.Alpha between
0 and 1. A value close to 1 gives a higher importance to the last RTT
measurement. The range of possible values and the actual value given to
the RTO.Alpha parameter are the following:
rtoAlphaIndex = 1 -> RTO.Alpha = 1/2
rtoAlphaIndex = 2 -> RTO.Alpha = 1/4
rtoAlphaIndex = 3 -> RTO.Alpha = 1/8
rtoAlphaIndex = 4 -> RTO.Alpha = 1/16
A new value of the attribute applies to both existing and new associations.

Sctp

rtoAlphaIndex

RNC

The attribute rtoAlphaIndex (Retransmission Timeout Alpha Index)


computes the value of the Smoothed Round-Trip Time (SRTT) for a
specific destination address. It weights the RTT values.
The value of this attribute is used to create a value of RTO.Alpha
between 0 and 1. A value close to 1 gives a higher importance to the last
RTT measurement. The range of possible values and the actual value
given to the RTO.Alpha parameter are the following:
rtoAlphaIndex = 1 -> RTO.Alpha = 1/2
rtoAlphaIndex = 2 -> RTO.Alpha = 1/4
rtoAlphaIndex = 3 -> RTO.Alpha = 1/8
rtoAlphaIndex = 4 -> RTO.Alpha = 1/16
A new value of the attribute applies to both existing and new
associations.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

rtoBetaIndex

RBS DUW

Network Parameters

The attribute rtoBetaIndex (Retransmission Timeout Beta Index) computes long


the value of RTTVar (Round Trip Time Variation) of a destination address.

208 (520)
1..4

1..4

The value of this attribute is used to create a value of RTO.Beta between 0


and 1. A value close to 1 gives a higher importance to the last observed
variation. The range of possible values and the actual value given to the
RTO.Beta parameter are the following:
rtoBetaIndex = 1 -> RTO.Beta = 1/2
rtoBetaIndex = 2 -> RTO.Beta = 1/4
rtoBetaIndex = 3 -> RTO.Beta = 1/8
rtoBetaIndex = 4 -> RTO.Beta = 1/16
A new value of the attribute applies to both existing and new associations.

Sctp

rtoBetaIndex

RNC

The attribute rtoBetaIndex (Retransmission Timeout Beta Index) computes long


the value of RTTVar (Round Trip Time Variation) of a destination address.
The value of this attribute is used to create a value of RTO.Beta
between 0 and 1. A value close to 1 gives a higher importance to the last
observed variation. The range of possible values and the actual value given
to the RTO.Beta parameter are the following:
rtoBetaIndex = 1 -> RTO.Beta = 1/2
rtoBetaIndex = 2 -> RTO.Beta = 1/4
rtoBetaIndex = 3 -> RTO.Beta = 1/8
rtoBetaIndex = 4 -> RTO.Beta = 1/16
A new value of the attribute applies to both existing and new
associations.

Sctp

sctpAssocDeleteTimeout

RBS DUW

The number of hours an SctpAssociation MO is allowed to stay in the


operational state DISABLED before it is automatically deleted.

long

1..168

168

long

1..168

168

If the association is re-established later, a new SctpAssociation MO is


created.
A new value of the attribute applies to both existing and new associations.
Unit: 1 hours
Sctp

sctpAssocDeleteTimeout

RNC

The number of hours an SctpAssociation MO is allowed to stay in the


operational state DISABLED before it is automatically deleted.
If the association is re-established later, a new SctpAssociation MO
is created.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 hours

Sctp
Sctp

Prepared: EZIEAGA

SctpId
SctpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

switchbackMaxThreshold

RBS DUW

Network Parameters

The maximum value of the number of consecutive successful heartbeats


long
that must be sent over the preferred primary path before switchback can be
performed.

209 (520)
1..65535

65535

1..65535

65535

1..65535

The value of this attribute has the following relationship to the value of
switchbackMinThreshold: switchbackMaxThreshold >=
switchbackMinThreshold.
A new value of the attribute applies to both existing and new associations.
The attribute is used for the EXPONENTIAL_BACKOFF switchback mode
only.
If this value is greater than 1, it can take longer to switch back to the
preferred primary path.
Unit: 1 attempts

Sctp

switchbackMaxThreshold

RNC

The maximum value of the number of consecutive successful heartbeats


long
that must be sent over the preferred primary path before switchback can be
performed.
The value of this attribute has the following relationship to the value
of switchbackMinThreshold: switchbackMaxThreshold >=
switchbackMinThreshold.
A new value of the attribute applies to both existing and new
associations.
The attribute is used for the EXPONENTIAL_BACKOFF switchback
mode only.
If this value is greater than 1, it can take longer to switch back to
the preferred primary path.
Unit: 1 attempts

Sctp

switchbackMinThreshold

RBS DUW

The minimum and initial values for the number of consecutive successful
heartbeats that must be sent over the preferred primary path before
switchback can be performed.

long

The value of this attribute has the following relationship to the value of
switchbackMaxThreshold: switchbackMinThreshold <=
switchbackMaxThreshold.
A new value of the attribute applies to both existing and new associations.
The attribute is used for the EXPONENTIAL_BACKOFF switchback mode
only.
If this value is greater than 1, it can take longer to switch back to the
preferred primary path.
Unit: 1 attempts

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

switchbackMinThreshold

RNC

Network Parameters

The minimum and initial values for the number of consecutive successful
heartbeats that must be sent over the preferred primary path before
switchback can be performed.

long

210 (520)
1..65535

The value of this attribute has the following relationship to the value
of switchbackMaxThreshold: switchbackMinThreshold <=
switchbackMaxThreshold.
A new value of the attribute applies to both existing and new
associations.
The attribute is used for the EXPONENTIAL_BACKOFF switchback
mode only.
If this value is greater than 1, it can take longer to switch back to
the preferred primary path.
Unit: 1 attempts

Sctp

switchbackMode

RBS DUW

The type of switchback behavior.

SwitchbackModeType

NO_SWITCHBACK = 0
IMMEDIATE_SWITCHBACK = 1
EXPONENTIAL_BACKOFF = 2

NO_SWITCHBAC IMMEDIATE_SWITCHBAC
K(0)
K(1)

SwitchbackModeType

NO_SWITCHBACK = 0
IMMEDIATE_SWITCHBACK = 1
EXPONENTIAL_BACKOFF = 2

NO_SWITCHBAC IMMEDIATE_SWITCHBAC
K(0)
K(1)

See also pathSelection.


Sctp

switchbackMode

RNC

The type of switchback behavior.

Sctp

tSack

RBS DUW

The time delay for sending the Selective Acknowledgement (SACK), that is, long
the time from reception of the DATA chunk to sending of the SACK chunk.

0..50

0..50

1..180

60

60

A new value of the attribute does not change the current measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp

tSack

RNC

The time delay for sending the Selective Acknowledgement (SACK), that is, long
the time from reception of the DATA chunk to sending of the SACK chunk.
A new value of the attribute does not change the current
measurement
interval. It applies only to subsequent intervals.
A new value of the attribute applies to both existing and new
associations.
Unit: 1 cs (centisecond, that is 0.01 second)

Sctp
Sctp
Sctp

userLabel
userLabel
validCookieLife

RBS DUW
RNC
RBS DUW

Label for free use.


string
Label for free use.
string
The attribute sets the lifespan of the State Cookie sent in the INIT_ACK
long
chunk. It limits the amount of time between sending the INIT_ACK and the
reception of a COOKIE_ECHO chunk when establishing an association.
It is recommended that the value of this attribute has the following
relationship to the values of other attributes:
validCookieLife >= maximumRto * maxInitialRtrAtt.
A new value of the attribute does not apply to associations that are already
established.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sctp

validCookieLife

RNC

Network Parameters

The attribute sets the lifespan of the State Cookie sent in the INIT_ACK
long
chunk. It limits the amount of time between sending the INIT_ACK and the
reception of a COOKIE_ECHO chunk when establishing an association.

211 (520)
1..180

60

60

It is recommended that the value of this attribute has the following


relationship to the values of other attributes:
validCookieLife >= maximumRto * maxInitialRtrAtt.
A new value of the attribute does not apply to associations that are
already established.
Unit: 1 s

SctpAssociation
SctpAssociation
SctpAssociation

clientRef
clientRef
creationTimeStamp

RBS DUW
RNC
RBS DUW

Reference to corresponding client's MO.


Reference to corresponding client?s MO.
The timestamp when the SctpAssociation MO instance was created.

ManagedObject
ManagedObject
string

Format example:
"Date: 2012-02-20, Time: 20:52:11"
SctpAssociation

creationTimeStamp

RNC

The timestamp when the SctpAssociation MO instance was created.

string

Format example:
"Date: 2012-02-20, Time: 20:52:11"
SctpAssociation

lastCommLostOrigin

RBS DUW

The originator of the last transition from the ENABLED to the DISABLED
operational state.

CommLostOrigin

UNKNOWN = 0
LOCAL = 1
REMOTE = 2

CommLostOrigin

UNKNOWN = 0
LOCAL = 1
REMOTE = 2

CommLostReason

UNKNOWN = 0
SCTP_RESTART = 1
SHUTDOWN_FAILURE = 2
USER_REQUEST_TERMINATE = 3
UNDETERMINED_ERROR = 4
PEER_REQUEST_ABORT = 5
MAX_RETRANSMIT_FAILED = 6
RESOURCE_ERROR = 7
PEER_REQUESTED_TERMINATE
=8
NO_USER_DATA_IN_CHUNK = 9
DATA_REASSEMBLY_ERROR = 10
STREAM_SEQ_ERROR = 11
INVALID_SACK = 12
LOCAL_REQUEST_ABORT = 13
INVALID_STREAM_ID = 14
INVALID_MAND_PARAM = 15

Specifies whether local or remote node has caused the last closure of the
association.
SctpAssociation

lastCommLostOrigin

RNC

The originator of the last transition from the ENABLED to the DISABLED
operational state.
Specifies whether local or remote node has caused the last closure
of the association.

SctpAssociation

lastCommLostReason

RBS DUW

The reason for the last transition from the ENABLED to the DISABLED
operational state.

RESTART_WITH_NEW_ADDRESSE
S = 16
PROTOCOL_VIOLATION = 17
ICMP_RECEIVED = 18
NO_USER_CONNECTION = 19
ZERO_RWND_SUPERVISION_TIME
R_EXPIRED = 20

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SctpAssociation

lastCommLostReason

RNC

Network Parameters

The reason for the last transition from the ENABLED to the DISABLED
operational state.

CommLostReason

212 (520)
UNKNOWN = 0
SCTP_RESTART = 1
SHUTDOWN_FAILURE = 2
USER_REQUEST_TERMINATE = 3
UNDETERMINED_ERROR = 4
PEER_REQUEST_ABORT = 5
MAX_RETRANSMIT_FAILED = 6
RESOURCE_ERROR = 7
PEER_REQUESTED_TERMINATE
=8
NO_USER_DATA_IN_CHUNK = 9
DATA_REASSEMBLY_ERROR = 10
STREAM_SEQ_ERROR = 11
INVALID_SACK = 12
LOCAL_REQUEST_ABORT = 13
INVALID_STREAM_ID = 14
INVALID_MAND_PARAM = 15
RESTART_WITH_NEW_ADDRESSE
S = 16
PROTOCOL_VIOLATION = 17
ICMP_RECEIVED = 18
NO_USER_CONNECTION = 19
ZERO_RWND_SUPERVISION_TIME
R_EXPIRED = 20

SctpAssociation

lastCommLostTimeStamp

RBS DUW

The timestamp of the last transition from the ENABLED to the DISABLED
operational state.

string

Format example:
"Date: 2012-02-20, Time: 10:52:11"
Initial value: "No value"
SctpAssociation

lastCommLostTimeStamp

RNC

The timestamp of the last transition from the ENABLED to the DISABLED
operational state.

string

Format example:
"Date: 2012-02-20, Time: 10:52:11"
Initial value: "No value"
SctpAssociation
SctpAssociation
SctpAssociation

localIpAddress1
localIpAddress1
localIpAddress2

RBS DUW
RNC
RBS DUW

The first IP address of the local endpoint.


The first IP address of the local endpoint.
The second IP address of the local endpoint.

string
string
string

The value "" means that the local endpoint of the association is singlehomed.
SctpAssociation

localIpAddress2

RNC

The second IP address of the local endpoint.

string

The value "" means that the local endpoint of the association is
single-homed.
SctpAssociation
SctpAssociation
SctpAssociation

localPortNumber
localPortNumber
localPrimaryIpAddress

RBS DUW
RNC
RBS DUW

SctpAssociation

localPrimaryIpAddress

RNC

SctpAssociation

operationalState

RBS DUW

The port number of the local endpoint of the association.


The port number of the local endpoint of the association.
The local IP address of the active primary path. The active primary path is
the path which is used for outgoing traffic.
The local IP address of the active primary path. The active primary path is
the path which is used for outgoing traffic.
The operational state.

long
long
string
string
OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED if the association is established, and


DISABLED if the association is closed.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SctpAssociation

operationalState

RNC

Network Parameters

The operational state.

213 (520)

OperState

DISABLED = 0
ENABLED = 1

The operational state is ENABLED if the association is established,


and DISABLED if the association is closed.
SctpAssociation
SctpAssociation
SctpAssociation

remoteIpAddress1
remoteIpAddress1
remoteIpAddress2

RBS DUW
RNC
RBS DUW

The first IP address of the remote endpoint.


The first IP address of the remote endpoint.
The second IP address of the remote endpoint.

string
string
string

The value "" means that the remote endpoint of the association is singlehomed.
SctpAssociation

remoteIpAddress2

RNC

The second IP address of the remote endpoint.

string

The value "" means that the remote endpoint of the association is
single-homed.
SctpAssociation
SctpAssociation
SctpAssociation

remotePortNumber
remotePortNumber
remotePrimaryIpAddress

RBS DUW
RNC
RBS DUW

SctpAssociation

remotePrimaryIpAddress

RNC

SctpAssociation
SctpAssociation
SctpAssociation
SctpAssociation
SctpProfile
SctpProfile
Sts1SpeTtp

SctpAssociationId
SctpAssociationId
sctpProfileRef
sctpProfileRef
dscp
sctpProfileId
aisPReporting

RBS DUW
RNC
RBS DUW
RNC
RBS 6401
RBS 6401
RBS DUW

The port number of the remote endpoint of the association.


The port number of the remote endpoint of the association.
The remote IP address of the active primary path. The active primary path
is the path which is used for outgoing traffic.
The remote IP address of the active primary path. The active primary path
is the path which is used for outgoing traffic.
The value component of the RDN.
The value component of the RDN.
Reference to an SctpProfile instance.
Reference to an SctpProfile instance.
The DSCP value used.
Value component of the RDN for SctpProfile.
Indicates whether the alarms Alarm Indication Signal - P (AIS-P) are to be
issued.

long
long
string
string
string
string
SctpProfile
SctpProfile
uint8
string
boolean

0..64

40
0

true - reporting enabled.


false - reporting disabled.
Sts1SpeTtp

aisPReporting

RNC

Indicates whether the alarms Alarm Indication Signal - P (AIS-P) are to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Sts1SpeTtp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sts1SpeTtp

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

Sts1SpeTtp

expectedPathTrace

RBS DUW

The expected path trace.

214 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
An empty string means that the detection of Trace Identifier Mismatch
(TIM) is disabled. This attribute is set to an empty string every time the
attribute pathTraceFormat is set.
Sts1SpeTtp

expectedPathTrace

RNC

The expected path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
An empty string means that the detection of Trace Identifier
Mismatch (TIM) is disabled. This attribute is set to an empty string every
time the attribute pathTraceFormat is set.

Sts1SpeTtp

operationalState

RBS DUW

The operational state.

OperState

Sts1SpeTtp

operationalState

RNC

The operational state.

OperState

Sts1SpeTtp

rdiPReporting

RBS DUW

Indicates whether the alarms Remote Defect Indication - P (RDI-P) are to


be issued.

boolean

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0

true - reporting enabled.


false - reporting disabled.
Sts1SpeTtp

rdiPReporting

RNC

Indicates whether the alarms Remote Defect Indication - P (RDI-P) are to


be issued.

boolean

true - reporting enabled.


false - reporting disabled.
Sts1SpeTtp
Sts1SpeTtp

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserve this MO instance.


Contains an MO instance that reserve this MO instance.

ManagedObject
ManagedObject

Sts1SpeTtp

Sts1SpeTtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.


Sts1SpeTtp

Sts1SpeTtpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sts1SpeTtp

timConsequentAction

RBS DUW

Network Parameters

215 (520)

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.

true - enabled.
false - disabled.
Sts1SpeTtp

timConsequentAction

RNC

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.
true - enabled.
false - disabled.

Sts1SpeTtp

transmittedPathTrace

RBS DUW

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
Sts1SpeTtp

transmittedPathTrace

RNC

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
Sts1SpeTtp
Sts1SpeTtp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Sts3CspeTtp

aisPReporting

RBS DUW

Indicates whether the alarms Alarm Indication Signal - P (AIS-P) are to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Sts3CspeTtp

aisPReporting

RNC

Indicates whether the alarms Alarm Indication Signal - P (AIS-P) are to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Sts3CspeTtp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sts3CspeTtp

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

Sts3CspeTtp

expectedPathTrace

RBS DUW

The expected path trace.

216 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
An empty string means that the detection of Trace Identifier Mismatch
(TIM) is disabled. This attribute is set to an empty string every time the
attribute pathTraceFormat is set.
Sts3CspeTtp

expectedPathTrace

RNC

The expected path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
An empty string means that the detection of Trace Identifier
Mismatch (TIM) is disabled. This attribute is set to an empty string every
time the attribute pathTraceFormat is set.

Sts3CspeTtp

operationalState

RBS DUW

The operational state.

OperState

Sts3CspeTtp

operationalState

RNC

The operational state.

OperState

Sts3CspeTtp

rdiPReporting

RBS DUW

Indicates whether the alarms Remote Defect Indication - P (RDI-P) are to


be issued.

boolean

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0

true - reporting enabled.


false - reporting disabled.
Sts3CspeTtp

rdiPReporting

RNC

Indicates whether the alarms Remote Defect Indication - P (RDI-P) are to


be issued.

boolean

true - reporting enabled.


false - reporting disabled.
Sts3CspeTtp

reservedBy

RBS DUW

Contains an MO instance that reserve this MO instance.

AtmPort

Identity of the AtmPort reserving this MO.


Sts3CspeTtp

reservedBy

RNC

Contains an MO instance that reserve this MO instance.

AtmPort

Identity of the AtmPort reserving this MO.


Sts3CspeTtp

Sts3CspeTtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Sts3CspeTtp

Sts3CspeTtpId

RNC

Network Parameters

The value component of the RDN.

217 (520)

string

It is set automatically when the MO instance is created.


Sts3CspeTtp

timConsequentAction

RBS DUW

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.

true - enabled.
false - disabled.
Sts3CspeTtp

timConsequentAction

RNC

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.
true - enabled.
false - disabled.

Sts3CspeTtp

transmittedPathTrace

RBS DUW

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
Sts3CspeTtp

transmittedPathTrace

RNC

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
Sts3CspeTtp
Sts3CspeTtp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

SwitchInternalLinkPort

portNumber

RBS DUW

Indicates the SILI port number.

long

SwitchInternalLinkPort

portNumber

RNC

Unique within a board.


Indicates the SILI port number.

long

Unique within a board.


SwitchInternalLinkPort
SwitchInternalLinkPort
SwitchInternalLinkPort
SwitchInternalLinkPort
SwitchInternalLinkPort
SwitchInternalLinkPort
SwitchPortStp
SwitchPortStp

remotePortRef
remotePortRef
SwitchInternalLinkPortId
SwitchInternalLinkPortId
userLabel
userLabel
actualPathCost
actualPathCost

RBS DUW
RNC
RBS DUW
RNC
RBS DUW
RNC
RBS DUW
RNC

Reference to the remote port detected through the cable.


Reference to the remote port detected through the cable.
The value component of the RDN.
The value component of the RDN.
Label for free use.
Label for free use.
Actual path cost.
Actual path cost.

ManagedObject
ManagedObject
string
string
string
string
long
long

1..200000000
1..200000000

SwitchPortStp

configuredPathCost

RBS DUW

Configured path cost.

long

1..200000000

20000

20000

If manualPathCost is true, the value of the attribute actualPathCost will be


determined by this attribute.
If manualPathCost is false, the value of the attribute actualPathCost may
differ from the value of this attribute.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchPortStp

configuredPathCost

RNC

Network Parameters

Configured path cost.

218 (520)

long

1..200000000

20000

20000

long

0..65536

600

600

long

0..65536

600

600

If manualPathCost is true, the value of the attribute actualPathCost


will be determined by this attribute.
If manualPathCost is false, the value of the attribute actualPathCost
may differ from the value of this attribute.
SwitchPortStp

edgePortBpduGuardTimeOut

RBS DUW

The time before an edge port blocked with BPDU Guard goes unblocked.
If this attribute is set to 0, manual interaction via the action
unblockEdgePort is needed.
Unit: 1 s

SwitchPortStp

edgePortBpduGuardTimeOut

RNC

The time before an edge port blocked with BPDU Guard goes unblocked.
If this attribute is set to 0, manual interaction via the action
unblockEdgePort is needed.
Unit: 1 s

SwitchPortStp

edgePortMode

RBS DUW

The behavior of an edge port.

EdgePortMode

ADMIN_EDGE_OFF = 0
ADMIN_EDGE_O ADMIN_EDGE_OFF(0)
AUTO_EDGE = 1
FF(0)
ADMIN_EDGE_ON = 2
ADMIN_EDGE_BPDU_GUARD = 3
ADMIN_EDGE_BPDU_FILTER = 4

EdgePortMode

ADMIN_EDGE_OFF = 0
ADMIN_EDGE_O ADMIN_EDGE_OFF(0)
AUTO_EDGE = 1
FF(0)
ADMIN_EDGE_ON = 2
ADMIN_EDGE_BPDU_GUARD = 3
ADMIN_EDGE_BPDU_FILTER = 4

Setting the edgePortMode may cause a short link failure (several seconds).
Setting the edgePortMode to ADMIN_EDGE_BPDU_GUARD or
ADMIN_EDGE_BPDU_FILTER turns on the external link redundancy
feature if:
- the MO SwitchPortStp is a child of EthernetSwitchModulePort, and
- the attribute externalPort in MO EthernetSwitchModulePort is true.
This disables all backplane ports in the subrack if the front port is disabled,
so these modes cannot be used to preconfigure external ports without
links.

SwitchPortStp

edgePortMode

RNC

The behavior of an edge port.


Setting the edgePortMode may cause a short link failure (several
seconds).
Setting the edgePortMode to ADMIN_EDGE_BPDU_GUARD or
ADMIN_EDGE_BPDU_FILTER turns on the external link redundancy
feature if:
- the MO SwitchPortStp is a child of EthernetSwitchModulePort,
and
- the attribute externalPort in MO EthernetSwitchModulePort is true.
This disables all backplane ports in the subrack if the front port is
disabled, so these modes cannot be used to preconfigure external ports
without links.

SwitchPortStp

l2gpActive

RBS DUW

Enables L2GP on this port.

boolean

There can be a maximum of 16 instances of SwitchPortStp with l2gpActive


= true in a node.
SwitchPortStp

l2gpActive

RNC

Enables L2GP on this port.

boolean

There can be a maximum of 16 instances of SwitchPortStp with


l2gpActive = true in a node.
SwitchPortStp

Prepared: EZIEAGA

l2gpBpduReceive

RBS DUW

Enables reception of BPDUs on an L2GP-enabled port.


boolean
Dependencies: If l2gpActive is set to false, this attribute must be set to true.

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

SwitchPortStp

l2gpBpduReceive

RNC

Enables reception of BPDUs on an L2GP-enabled port.


boolean
Dependencies: If l2gpActive is set to false, this attribute must be set
to true.

SwitchPortStp

l2gpPortPriority

RBS DUW

SwitchPortStp

l2gpPortPriority

RNC

SwitchPortStp

l2gpPseudoRootId

RBS DUW

The priority of the L2GP port in relation to other L2GP ports within the
RSTP domain. The value 1 indicates the highest priority.
The priority of the L2GP port in relation to other L2GP ports within the
RSTP domain. The value 1 indicates the highest priority.
The bridge ID for the pseudo root bridge.

219 (520)

long

1..16

16

long

1..16

16

string

Automatically calculated by the system based on the l2gpPortPriority.


SwitchPortStp

l2gpPseudoRootId

RNC

The bridge ID for the pseudo root bridge.

string

Automatically calculated by the system based on the


l2gpPortPriority.
SwitchPortStp

manualPathCost

RBS DUW

Determines the possibility to manually configure the path cost.

boolean

0 FALSE(0)

boolean

FALSE(0)

If this attribute is set to true, the path cost can be configured by setting the
attribute configuredPathCost.
If this attribute is set to false, the system ignores the attribute
configuredPathCost.
SwitchPortStp

manualPathCost

RNC

Determines the possibility to manually configure the path cost.


If this attribute is set to true, the path cost can be configured by
setting the attribute configuredPathCost.
If this attribute is set to false, the system ignores the attribute
configuredPathCost.

SwitchPortStp

priority

RBS DUW

Port priority.

Priority

PRIO_0 = 0
PRIO_16 = 16
PRIO_32 = 32
PRIO_48 = 48
PRIO_64 = 64
PRIO_80 = 80
PRIO_96 = 96
PRIO_112 = 112
PRIO_128 = 128
PRIO_144 = 144
PRIO_160 = 160
PRIO_176 = 176
PRIO_192 = 192
PRIO_208 = 208
PRIO_224 = 224
PRIO_240 = 240

PRIO_128(128)

Priority

PRIO_0 = 0
PRIO_16 = 16
PRIO_32 = 32
PRIO_48 = 48
PRIO_64 = 64
PRIO_80 = 80
PRIO_96 = 96
PRIO_112 = 112
PRIO_128 = 128
PRIO_144 = 144
PRIO_160 = 160
PRIO_176 = 176
PRIO_192 = 192
PRIO_208 = 208
PRIO_224 = 224
PRIO_240 = 240

PRIO_128(128)

The port with the lowest port priority value will be selected as Root port in
the case when more than one port is connected to the Root bridge. If two
ports have the same priority the one with the lowest port number gets the
best priority.
The value must be a multiple of 16.

SwitchPortStp

priority

RNC

Port priority.
The port with the lowest port priority value will be selected as Root
port in the case when more than one port is connected to the Root bridge.
If two ports have the same priority the one with the lowest port number gets
the best priority.
The value must be a multiple of 16.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchPortStp

protocolVersion

RBS DUW

SwitchPortStp

protocolVersion

RNC

SwitchPortStp

remoteBridgeId

RBS DUW

Network Parameters

The actual protocol version running on this port as the result of negotiation ProtocolVersion
with the remote switch port.
The actual protocol version running on this port as the result of negotiation ProtocolVersion
with the remote switch port.
The bridge id of the counterpart bridge in the spanning tree protocol
messaging.

220 (520)
STP = 0
RSTP = 1
STP = 0
RSTP = 1

string

This attribute is relevant only for ports with the role alternate or root.
The attribute consists of priority and macaddress combined into a string,
where the first 4 characters repesent the priority, and the last characters
represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"
SwitchPortStp

remoteBridgeId

RNC

The bridge id of the counterpart bridge in the spanning tree protocol


messaging.

string

This attribute is relevant only for ports with the role alternate or root.
The attribute consists of priority and macaddress combined into a
string, where the first 4 characters repesent the priority, and the last
characters represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"

Specifies the Root Path Cost used in Bridge Protocol Data Units (BPDUs)
transmitted from this port.

SwitchPortStp

rootPathCost

RBS DUW

long

SwitchPortStp

rootPathCost

RNC

Specifies the Root Path Cost used in Bridge Protocol Data Units (BPDUs)
transmitted from this port.

SwitchPortStp
SwitchPortStp
SwitchPortStp

settingsUsed
settingsUsed
stpRole

RBS DUW
RNC
RBS DUW

Indicates if the settings in this MO instance are used.


Indicates if the settings in this MO instance are used.
The STP role of the port.

boolean
boolean
StpRole

SwitchPortStp

stpRole

RNC

The STP role of the port.

StpRole

ROOT = 0
DESIGNATED = 1
ALTERNATE = 2
BACKUP = 3
UNKNOWN = 9

SwitchPortStp

stpState

RBS DUW

The STP state of the port.

StpState

DISABLED = 0
BLOCKING = 1
LISTENING = 2
DISCARDING = 3
LEARNING = 4
FORWARDING = 5
UNKNOWN = 9

SwitchPortStp

stpState

RNC

The STP state of the port.

StpState

DISABLED = 0
BLOCKING = 1
LISTENING = 2
DISCARDING = 3
LEARNING = 4
FORWARDING = 5
UNKNOWN = 9

Specification: IEEE Std 802.1D-2004


long

Specification: IEEE Std 802.1D-2004

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

ROOT = 0
DESIGNATED = 1
ALTERNATE = 2
BACKUP = 3
UNKNOWN = 9

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchPortStp

SwitchPortStpId

RBS DUW

Network Parameters

The value component of the RDN.

221 (520)

string

It is set automatically when the MO instance is created.


SwitchPortStp

SwitchPortStpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


SwitchPortStp
SwitchPortStp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

SwitchStp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Turns on or off the use of the Spanning Tree Protocol.


SHUTTING_DOWN is not supported and if set the value is changed to
LOCKED.
In case the parent MO is an instance of EthernetSwitchModule, this
attribute is not applicable and is ignored by the system.
SwitchStp

administrativeState

RNC

The administrative state.


Turns on or off the use of the Spanning Tree Protocol.
SHUTTING_DOWN is not supported and if set the value is
changed to LOCKED.
In case the parent MO is an instance of EthernetSwitchModule, this
attribute is not applicable and is ignored by the system.

SwitchStp

bridgeForwardDelay

RBS DUW

The delay used by the switch before changing to the Forwarding state, in
case of a port interoperating with a legacy STP switch.

long

40..300

150

150

long

40..300

150

150

long

10..100

20

20

If interoperability with legacy STP bridges is wanted, the value of


bridgeForwardDelay must be set to greater than or equal to
(bridgeMaxAge/2 + 10).
Refer to the description of the relevant board for details on validation of this
relationship.
Unit: 1 ds (0.1 s)
SwitchStp

bridgeForwardDelay

RNC

The delay used by the switch before changing to the Forwarding state, in
case of a port interoperating with a legacy STP switch.
If interoperability with legacy STP bridges is wanted, the value of
bridgeForwardDelay must be set to greater than or equal to
(bridgeMaxAge/2 + 10).
Refer to the description of the relevant board for details on
validation of this relationship.
Unit: 1 ds (0.1 s)

SwitchStp

bridgeHelloTime

RBS DUW

Interval between periodic transmissions of configuration messages by


designated ports.
If interoperability with legacy STP bridges is wanted, the value of
bridgeHelloTime must be set to less than or equal to (bridgeMaxAge/2 -10).
Ranges and limitations can vary between boards. Refer to the description
of the relevant board for details.
Unit: 1 ds (0.1 s)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchStp

bridgeHelloTime

RNC

Network Parameters

Interval between periodic transmissions of configuration messages by


designated ports.

long

222 (520)
10..100

20

20

60..400

60

60

If interoperability with legacy STP bridges is wanted, the value of


bridgeHelloTime must be set to less than or equal to (bridgeMaxAge/2 -10).
Ranges and limitations can vary between boards. Refer to the description
of the relevant board for details.
Unit: 1 ds (0.1 s)
SwitchStp

bridgeId

RBS DUW

The bridge ID of the switch.

string

The attribute consists of priority and macaddress combined into a string,


where the first 4 characters repesent the priority, and the last characters
represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"
SwitchStp

bridgeId

RNC

The bridge ID of the switch.

string

The attribute consists of priority and macaddress combined into a


string, where the first 4 characters repesent the priority, and the last
characters represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"

SwitchStp

bridgeMaxAge

RBS DUW

The maximum time interval before a switch, not receiving any BPDUs,
assumes that a network change has occurred.

long

If interoperability with legacy STP bridges is wanted, the value of


bridgeMaxAge must be set to greater than or equal to 2 x (bridgeHelloTime
+10).
The value of bridgeMaxAge is dependent on the switched network
topology, which is measured as the network diameter. The network
diameter is defined as: the number of RSTP-enabled switches between the
root switch and the switch with alternate ports that is farthest away from the
root switch. That is, the longest way that information needs to travel from
the root switch. Therefore, the network diameter is the number of hops + 1.
Set bridgeMaxAge to 4 x bridgeHelloTime + 10 x (network diameter - 1). In
the simplest recommended network, double-star topology with two or more
subracks, the network diameter is 4 if one link is temporarily out of order. If
a lower value of bridgeMaxAge is used, this might result in spontaneous
RSTP state transitions. If a higher value of bridgeMaxAge is used, the
RSTP convergence time increases during root switch failure.
Refer to the description of the relevant board for details on validation of this
relationship.
Unit: 1 ds (0.1 s)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchStp

bridgeMaxAge

RNC

Network Parameters

The maximum time interval before a switch, not receiving any BPDUs,
assumes that a network change has occurred.

long

223 (520)
60..400

60

60

If interoperability with legacy STP bridges is wanted, the value of


bridgeMaxAge must be set to greater than or equal to 2 x (bridgeHelloTime
+10).
The value of bridgeMaxAge is dependent on the switched network
topology, which is measured as the network diameter. The network
diameter is defined as: the number of RSTP-enabled switches between the
root switch and the switch with alternate ports that is farthest away from the
root switch. That is, the longest way that information needs to travel from
the root switch. Therefore, the network diameter is the number of hops + 1.
Set bridgeMaxAge to 4 x bridgeHelloTime + 10 x (network diameter - 1). In
the simplest recommended network, double-star topology with two or more
subracks, the network diameter is 4 if one link is temporarily out of order. If
a lower value of bridgeMaxAge is used, this might result in spontaneous
RSTP state transitions. If a higher value of bridgeMaxAge is used, the
RSTP convergence time increases during root switch failure.
Refer to the description of the relevant board for details on
validation of this relationship.
Unit: 1 ds (0.1 s)

SwitchStp

bridgePriority

RBS DUW

Switch priority used by the protocol.

BridgePriority

PRIO_0 = 0
PRIO_4096 = 4096
PRIO_8192 = 8192
PRIO_12288 = 12288
PRIO_16384 = 16384
PRIO_20480 = 20480
PRIO_24576 = 24576
PRIO_28672 = 28672
PRIO_32768 = 32768
PRIO_36864 = 36864
PRIO_40960 = 40960
PRIO_45056 = 45056
PRIO_49152 = 49152
PRIO_53248 = 53248
PRIO_57344 = 57344
PRIO_61440 = 61440

PRIO_32768(3276
8)

BridgePriority

PRIO_0 = 0
PRIO_4096 = 4096
PRIO_8192 = 8192
PRIO_12288 = 12288
PRIO_16384 = 16384
PRIO_20480 = 20480
PRIO_24576 = 24576
PRIO_28672 = 28672
PRIO_32768 = 32768
PRIO_36864 = 36864
PRIO_40960 = 40960
PRIO_45056 = 45056
PRIO_49152 = 49152
PRIO_53248 = 53248
PRIO_57344 = 57344
PRIO_61440 = 61440

PRIO_32768(3276
8)

StpMode

RSTP = 0

RSTP(0)

The value must be a multiple of 4096.


The preferred rootswitch must have a low value and the standby rootswitch
must have a value that is almost as low. To achieve as good convergence
time as possible, when the rootswitch is lost, all switches must be set to a
value that increases with the distance to the preferred rootswitch.

SwitchStp

bridgePriority

RNC

Switch priority used by the protocol.


The value must be a multiple of 4096.
The preferred rootswitch must have a low value and the standby
rootswitch must have a value that is almost as low. To achieve as good
convergence time as possible, when the rootswitch is lost, all switches
must be set to a value that increases with the distance to the preferred
rootswitch.

SwitchStp

mode

RBS DUW

The kind of spanning tree protocol used.

RSTP(0)

The system supports Rapid Spanning Tree Protocol, RSTP.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchStp

mode

RNC

The kind of spanning tree protocol used.

Network Parameters

224 (520)

StpMode

RSTP = 0

RSTP(0)

RSTP(0)

The system supports Rapid Spanning Tree Protocol, RSTP.


SwitchStp

rootBridgeId

RBS DUW

The bridge ID of the switch defined as the root bridge.

string

The attribute consists of priority and macaddress combined into a string,


where the first 4 characters repesent the priority, and the last characters
represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"
SwitchStp

rootBridgeId

RNC

The bridge ID of the switch defined as the root bridge.

string

The attribute consists of priority and macaddress combined into a


string, where the first 4 characters repesent the priority, and the last
characters represent the macaddress. A hyphen (-) separates the two.
Example: "0000-00:00:00:00:00:00"

SwitchStp
SwitchStp

rootPortNumber
rootPortNumber

RBS DUW
RNC

The root port number.


The root port number.

long
long

SwitchStp

stpForwardDelay

RBS DUW

The actual value of the delay used by the switch before changing to the
long
Forwarding state, in case of a port interoperating with a legacy STP switch.

40..300

This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)
SwitchStp

stpForwardDelay

RNC

The actual value of the delay used by the switch before changing to the
long
Forwarding state, in case of a port interoperating with a legacy STP switch.

40..300

This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)

SwitchStp

stpHelloTime

RBS DUW

Interval between periodic transmissions of configuration messages by


designated ports.
This is the actual value that this bridge is currently using.

long

10..100

long

10..100

long

60..400

long

60..400

This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)
SwitchStp

stpHelloTime

RNC

Interval between periodic transmissions of configuration messages by


designated ports.
This is the actual value that this bridge is currently using.
This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)

SwitchStp

stpMaxAge

RBS DUW

The actual value of the maximum time interval before a switch, not
receiving any BPDUs, assumes that a network change has occurred.
This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)

SwitchStp

stpMaxAge

RNC

The actual value of the maximum time interval before a switch, not
receiving any BPDUs, assumes that a network change has occurred.
This value is propagated from the root switch in the STP domain.
Unit: 1 ds (0.1 s)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SwitchStp

SwitchStpId

RBS DUW

Network Parameters

The value component of the RDN.

225 (520)

string

It is set automatically when the MO instance is created.


SwitchStp

SwitchStpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


SwitchStp

topologyChangeTime

RBS DUW

The time since the latest topology change occurred.

long

Unit: 1 s
SwitchStp

topologyChangeTime

RNC

The time since the latest topology change occurred.

long

Unit: 1 s
SwitchStp

transmitHoldCount

RBS DUW

The maximum number of BPDUs that may be sent on one port to a


neighboring switch.

long

1..10

long

1..10

When the maximum number is reached, only one more BPDU may be sent
per second. A high value gives better convergence time. The fastest
convergence is achieved with the value 10 in the entire RSTP domain.
Interworking switches must have the same value.
Unit: 1 BPDUs

SwitchStp

transmitHoldCount

RNC

The maximum number of BPDUs that may be sent on one port to a


neighboring switch.
When the maximum number is reached, only one more BPDU may
be sent per second. A high value gives better convergence time. The
fastest convergence is achieved with the value 10 in the entire RSTP
domain.
Interworking switches must have the same value.
Unit: 1 BPDUs

SwitchStp
SwitchStp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

Synchronization

degradationIsFault

RBS DUW

Determines whether a transmission link degradation (for example, high bit- FaultCriteria
error rate) is interpreted as a synchronization reference fault or not. This
attribute is applicable only for traffic carrying synchronization references.

DEGR_NOT_FAULT = 0
DEGR_IS_FAULT = 1

DEGR_NOT_FAU
LT(0)

Synchronization

degradationIsFault

RNC

Determines whether a transmission link degradation (for example, high bit- FaultCriteria
error rate) is interpreted as a synchronization reference fault or not. This
attribute is applicable only for traffic carrying synchronization references.

DEGR_NOT_FAULT = 0
DEGR_IS_FAULT = 1

DEGR_NOT_FAU
LT(0)

Synchronization
Synchronization

dscp
featureStatePtpFreq

RBS 6401
RBS DUW

DSCP to be used in NTP and PTP synchronization protocols.


Specifies the ptp frequency feature state.

int32
ActivationVals

Synchronization

featureStatePtpFreq

RNC

Specifies the ptp frequency feature state.

ActivationVals

Synchronization

featureStatePtpTime

RBS DUW

Specifies the ptp time feature state.

ActivationVals

Synchronization

featureStatePtpTime

RNC

Specifies the ptp time feature state.

ActivationVals

Synchronization

featureStateSyncEth

RBS DUW

Specifies the synchronous ethernet feature state.

ActivationVals

Synchronization

featureStateSyncEth

RNC

Specifies the synchronous ethernet feature state.

ActivationVals

Synchronization

licenseStatePtpFreq

RBS DUW

Specifies the ptp frequency license state.

StateVals

Synchronization

licenseStatePtpFreq

RNC

Specifies the ptp frequency license state.

StateVals

Prepared: EZIEAGA

string
string

Date: 2014-05-27
Sheet: 14.0.2

0..63
ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0
ACTIVATED = 1
DEACTIVATED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0

54
DEACTIVATED(0)
DEACTIVATED(0)
DEACTIVATED(0)
DEACTIVATED(0)
DEACTIVATED(0)
DEACTIVATED(0)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Synchronization

licenseStatePtpTime

RBS DUW

Specifies the ptp time license state.

StateVals

Synchronization

licenseStatePtpTime

RNC

Specifies the ptp time license state.

StateVals

Synchronization

licenseStateSyncEth

RBS DUW

Specifies the synchronous ethernet license state.

StateVals

Synchronization

licenseStateSyncEth

RNC

Specifies the synchronous ethernet license state.

StateVals

Synchronization

nodeSystemClock

RBS DUW

State of the system clock on the node.

ClockState

Synchronization

nodeSystemClock

RNC

State of the system clock on the node.

ClockState

Synchronization

sfnInitializationTime

RNC

Specifies the time when SFN is initialized to zero.

string

226 (520)
ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0
UNKNOWN_MODE = 0
STARTUP_MODE = 1
LOCKED_MODE = 2
HOLD_OVER_MODE = 3
FREE_RUNNING_MODE = 4
FAILED_MODE = 5
LOSS_OF_TRACKING_MODE = 6
NOT_APPLICABLE = 7
UNKNOWN_MODE = 0
STARTUP_MODE = 1
LOCKED_MODE = 2
HOLD_OVER_MODE = 3
FREE_RUNNING_MODE = 4
FAILED_MODE = 5
LOSS_OF_TRACKING_MODE = 6
NOT_APPLICABLE = 7
1980-0106T00:00:19

The time is TAI given as a string with the following format: <YYYYMM-DD>T<hh:mm:ss>
Synchronization
Synchronization

synchronizationId
SynchronizationId

RBS 6401
RBS DUW

Synchronization

SynchronizationId

RNC

Value component of the RDN.


The value component of the RDN.

string
string

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


Synchronization

syncRefActivity

RBS DUW

Synchronization

syncRefActivity

RNC

List of attributes for synchronization references, where each attribute


specifies whether the respective synchronization reference is active. Zero
or one reference is active.

RefActivity

INACTIVE = 1
ACTIVE = 2

RefActivity

INACTIVE = 1
ACTIVE = 2

The length of this list is 8.


List of attributes for synchronization references, where each attribute
specifies whether the respective synchronization reference is active. Zero
or one reference is active.
The length of this list is 8.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Synchronization

syncReference

RBS DUW

Network Parameters

List of resources for synchronization references. Possible references are:


E1PhysPathTerm, E3PhysPathTerm, J1PhysPathTerm, T1PhysPathTerm,
T3PhysPathTerm, Os155SpiTtp, TuSyncRef, IpSyncRef, GpsSyncRef,
PacketFrequencySyncRef, PacketTimeSyncRef, HptsiSyncRef,
GigaBitEthernet and GpsOutSyncLink. The IpSyncRef is not supported in
TUB1 nodes.

227 (520)

ManagedObject

A synchronization reference is added by using the action


addSyncRefResource.
If one value in this attribute is NULL, the respective values in the attributes
syncRefActivity, syncRefPriority and syncStatus are not relevant.
The length of this list is 8.

Synchronization

syncReference

RNC

List of resources for synchronization references. Possible references are:


E1PhysPathTerm, E3PhysPathTerm, J1PhysPathTerm, T1PhysPathTerm,
T3PhysPathTerm, Os155SpiTtp, TuSyncRef, IpSyncRef, GpsSyncRef,
PacketFrequencySyncRef, PacketTimeSyncRef, HptsiSyncRef and
GigaBitEthernet. The IpSyncRef is not supported in TUB1 nodes.

ManagedObject

A synchronization reference is added by using the action


addSyncRefResource.
If one value in this attribute is NULL, the respective values in the
attributes syncRefActivity, syncRefPriority and syncStatus are not relevant.
The length of this list is 8.

Synchronization

syncRefPriority

RBS DUW

Synchronization reference priority.

long

0..8

long

0..8

1 represents the highest and 8 the lowest priority. Every synchronization


reference must have a unique priority value. Value 0 means not applicable,
that is, no synchronization reference with this priority is defined.
This attribute is mandatory when adding a synchronization reference (using
the action addSyncRefResource).
A priority value can be changed with the action changeSyncRefPriority,
provided that the priority is not already assigned to some other
synchronization reference.
The length of this list is 8.

Synchronization

syncRefPriority

RNC

Synchronization reference priority.


1 represents the highest and 8 the lowest priority. Every
synchronization reference must have a unique priority value. Value 0
means not applicable, that is, no synchronization reference with this priority
is defined.
This attribute is mandatory when adding a synchronization
reference (using the action addSyncRefResource).
A priority value can be changed with the action
changeSyncRefPriority, provided that the priority is not already assigned to
some other synchronization reference.
The length of this list is 8.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Synchronization

syncRefStatus

RBS DUW

Network Parameters

List of status attributes for synchronization references.

228 (520)

RefState

FAILED = 0
DEGRADED = 1
LOSS_OF_TRACKING = 2
OK = 3
REF_PATH_FAILED_A = 4
REF_PATH_FAILED_B = 5
NOT_RELIABLE = 6
LOW_QUALITY = 7
PDV_PROBLEM = 8
NOT_SLAVE = 9

RefState

FAILED = 0
DEGRADED = 1
LOSS_OF_TRACKING = 2
OK = 3
REF_PATH_FAILED_A = 4
REF_PATH_FAILED_B = 5
NOT_RELIABLE = 6
LOW_QUALITY = 7
PDV_PROBLEM = 8
PUBLIC = 0
PRIVATE = 1

The length of this list is 8.

Synchronization

syncRefStatus

RNC

List of status attributes for synchronization references.


The length of this list is 8.

Synchronization

syncServerNetwork

RBS 6401

Set to PRIVATE when synchronization time servers are accessed through


an IPSec tunnel, otherwise with or without IPsec set to PUBLIC.

SyncServerNetwork

Synchronization
Synchronization

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

SyncServer

administrativeState

RBS 6401

The administrative state enables or disables the operation of the NTP or


PTP client function.
This is a convenience function to permit some or all instances to be
temporarily disabled.

BasicAdmState

LOCKED = 0
UNLOCKED = 1

SyncServer

protocol

RBS 6401

Used time protocol for synchronization.

Protocol

NTP = 0
PTP = 1

SyncServer

serverAddress

RBS 6401

This is the address of the synchronization server.

string

1..253

The serverAddress represents either a V4 IP address,a V6 IP address or a


DNS domain name.
SyncServer
SystemClockDistribution

syncServerId
availabilityStatus

RBS 6401
RBS DUW

Value component of the RDN.


The availability status.

string
AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
SystemClockDistribution

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

It contains details about operationalState.

SystemClockDistribution

operationalState

RBS DUW

The operational state.

OperState

SystemClockDistribution

operationalState

RNC

The operational state.

OperState

SystemClockDistribution
SystemClockDistribution
SystemClockDistribution
SystemClockDistribution
SystemClockDistribution
SystemClockDistribution
T1PhysPathTerm

reservedBy
reservedBy
SystemClockDistributionId
SystemClockDistributionId
userLabel
userLabel
administrativeState

RBS DUW
RNC
RBS DUW
RNC
RBS DUW
RNC
RBS DUW

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.
The value component of the RDN.
The value component of the RDN.
Label for free use.
Label for free use.
The administrative state.

ManagedObject
ManagedObject
string
string
string
string
AdmState

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
T1PhysPathTerm

administrativeState

RNC

The administrative state.

AdmState

Disturbances: Changing lower layer attributes may affect O&M


connectivity, if they are part of the O&M connection.
T1PhysPathTerm

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

229 (520)

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

boolean

true - reporting enabled.


false - reporting disabled.
T1PhysPathTerm

aisReporting

RNC

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1PhysPathTerm

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
T1PhysPathTerm

availabilityStatus

RNC

Network Parameters

The availability status.

230 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

T1PhysPathTerm

degDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

2..10

long

0..100

30

long

0..100

30

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
T1PhysPathTerm

degDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

T1PhysPathTerm

degDegThr

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.
Unit: 1 %
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

T1PhysPathTerm

degDegThr

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.
Unit: 1 %
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

T1PhysPathTerm

idlePattern

RBS DUW

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but setting


up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED -> A_LAW.

T1PhysPathTerm

idlePattern

RNC

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.
Changing from A_LAW or U_LAW to UNDEFINED is allowed, but
setting up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED ->
A_LAW.

T1PhysPathTerm

Prepared: EZIEAGA

lineNo

RBS DUW

The line number on the board.

long

Date: 2014-05-27
Sheet: 14.0.2

1..8

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

231 (520)

T1PhysPathTerm

lineNo

RNC

The line number on the board.

long

T1PhysPathTerm

loopback

RBS DUW

The loopback state of this physical path termination.

LoopbackState

1..8
NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

The attribute administrativeState must be set to LOCKED when setting the


attribute loopback.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
T1PhysPathTerm

loopback

RNC

The loopback state of this physical path termination.


The attribute administrativeState must be set to LOCKED when
setting the attribute loopback.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

T1PhysPathTerm

operationalState

RBS DUW

The operational state.

OperState

T1PhysPathTerm

operationalState

RNC

The operational state.

OperState

T1PhysPathTerm

rdiReporting

RBS DUW

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1PhysPathTerm

rdiReporting

RNC

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1PhysPathTerm
T1PhysPathTerm

reservedByImaLink
reservedByImaLink

RBS DUW
RNC

The identity of the ImaLink MO that reserves this MO instance.


The identity of the ImaLink MO that reserves this MO instance.

ImaLink
ImaLink

T1PhysPathTerm

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

T1PhysPathTerm

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

T1PhysPathTerm
T1PhysPathTerm

reservedByTraffic
reservedByTraffic

RBS DUW
RNC

The identity of the AtmPort MO that reserves this MO instance.


The identity of the AtmPort MO that reserves this MO instance.

AtmPort
AtmPort

T1PhysPathTerm

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
T1PhysPathTerm

shutDownTimeout

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

T1PhysPathTerm
T1PhysPathTerm

Prepared: EZIEAGA

T1PhysPathTermId
T1PhysPathTermId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
T1PhysPathTerm

transmissionMode

RBS DUW

Network Parameters

The type of transmission medium.

232 (520)

TransmissionMode

S_133 = 0
S_266 = 1
S_399 = 2
S_533 = 3
S_655 = 4
L_0 = 5
L_2000 = 6
L_4000 = 7
L_6000 = 8

S_133(0)

TransmissionMode

S_133 = 0
S_266 = 1
S_399 = 2
S_533 = 3
S_655 = 4
L_0 = 5
L_2000 = 6
L_4000 = 7
L_6000 = 8

S_133(0)

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.

T1PhysPathTerm

transmissionMode

RNC

The type of transmission medium.


Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

T1PhysPathTerm
T1PhysPathTerm

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

T1Ttp

aisReporting

RBS DUW

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1Ttp

aisReporting

RNC

Indicates whether the alarm PDH Alarm Indication Signal (AIS) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

T1Ttp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

T1Ttp

Prepared: EZIEAGA

degDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

Date: 2014-05-27
Sheet: 14.0.2

2..10

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

233 (520)

T1Ttp

degDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

T1Ttp

degDegThr

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

T1Ttp

degDegThr

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

T1Ttp

idlePattern

RBS DUW

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.

Unit: 1 %

Unit: 1 %
UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

UNDEFINED = 0
A_LAW = 1
U_LAW = 2

UNDEFINED(0)

UNDEFINED(0)

Changing from A_LAW or U_LAW to UNDEFINED is allowed, but setting


up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED -> A_LAW.

T1Ttp

idlePattern

RNC

The idle pattern applies only to ports using TDM switching. It defines the
IdlePattern
pattern being sent out on a timeslot that is not occupied by a 64 Kbit/s TDM
connection.
Changing from A_LAW or U_LAW to UNDEFINED is allowed, but
setting up one ET board with both U_LAW and A_LAW is not allowed. For
example, if you want to change from A_LAW to U_LAW on one ET board,
you must first change idlePattern to UNDEFINED on each physical port
belonging to the board. That is:
A_LAW -> UNDEFINED -> U_LAW, or U_LAW -> UNDEFINED ->
A_LAW.

T1Ttp

operationalState

RBS DUW

The operational state.

OperState

T1Ttp

operationalState

RNC

The operational state.

OperState

T1Ttp

rdiReporting

RBS DUW

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0

true - reporting enabled.


false - reporting disabled.
T1Ttp

rdiReporting

RNC

Indicates whether the alarm PDH Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T1Ttp
T1Ttp

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

T1Ttp
T1Ttp

reservedByImaLink
reservedByImaLink

RBS DUW
RNC

The identity of the ImaLink MO that reserves this MO instance.


The identity of the ImaLink MO that reserves this MO instance.

ImaLink
ImaLink

T1Ttp

T1TtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
T1Ttp

T1TtpId

RNC

Network Parameters

The value component of the RDN.

234 (520)

string

It is set automatically when the MO instance is created.


T1Ttp
T1Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

T3PhysPathTerm

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

T3PhysPathTerm

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

T3PhysPathTerm

aisReporting

RBS DUW

Indicates whether the alarm Alarm Indication Signal (AIS) is to be issued.

boolean

true - reporting enabled.


false - reporting disabled.
T3PhysPathTerm

aisReporting

RNC

Indicates whether the alarm Alarm Indication Signal (AIS) is to be issued.

boolean

true - reporting enabled.


false - reporting disabled.

T3PhysPathTerm

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

T3PhysPathTerm

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

T3PhysPathTerm
T3PhysPathTerm

lineNo
lineNo

RBS DUW
RNC

The line number on the board.


The line number on the board.

long
long

T3PhysPathTerm

loopback

RBS DUW

The loopback state of this physical path termination.

LoopbackState

The attribute administrativeState must be set to LOCKED when setting the


attribute loopback.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

1..2
1..2
NONE = 0
LINE = 1
SYSTEM = 2

NONE(0)

NONE(0)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
T3PhysPathTerm

loopback

RNC

Network Parameters

The loopback state of this physical path termination.

235 (520)

LoopbackState

NONE = 0
LINE = 1
SYSTEM = 2
DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

The attribute administrativeState must be set to LOCKED when


setting the attribute loopback.
T3PhysPathTerm

operationalState

RBS DUW

The operational state.

OperState

T3PhysPathTerm

operationalState

RNC

The operational state.

OperState

T3PhysPathTerm

rdiReporting

RBS DUW

Indicates whether the alarm Remote Defect Indication (RDI) is to be


issued.

boolean

NONE(0)

NONE(0)

true - reporting enabled.


false - reporting disabled.
T3PhysPathTerm

rdiReporting

RNC

Indicates whether the alarm Remote Defect Indication (RDI) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
T3PhysPathTerm

reservedBySync

RBS DUW

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

T3PhysPathTerm

reservedBySync

RNC

The identity of the Synchronization MO that reserves this MO instance.

Synchronization

T3PhysPathTerm
T3PhysPathTerm

reservedByTraffic
reservedByTraffic

RBS DUW
RNC

The identity of the AtmPort MO that reserves this MO instance.


The identity of the AtmPort MO that reserves this MO instance.

AtmPort
AtmPort

T3PhysPathTerm

shutDownTimeout

RBS DUW

The shut-down timer.

long

0..100000

1800

long

0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
T3PhysPathTerm

shutDownTimeout

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

T3PhysPathTerm
T3PhysPathTerm

T3PhysPathTermId
T3PhysPathTermId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

T3PhysPathTerm
T3PhysPathTerm

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

TimeSyncIo
TimeSyncIo

altitude
gpsRefState

RBS 6401
RBS 6401

Altitude in meters.
Indicates the status of the GPS receiver.

string
GpsSyncRef

TimeSyncIo
TimeSyncIo
TimeSyncIo
TimeSyncIo
TimingUnit

latitude
longitude
noOfSatellitesInView
timeSyncIOId
hptsiOutEnabled

RBS 6401
RBS 6401
RBS 6401
RBS 6401
RBS DUW

Latitude in degrees.
Longitude in degrees.
The number of satellites in view.
Value component of the RDN.
Set to true means GPS port is reversed to output with HPTSI protocol.

string
string
int32
string
boolean

HW_FAULT = 0
OK = 1
NO_TIME = 2

For details on which boards support the setting of hptsiOutEnabled = true,


see the description of the relevant board.
Dependencies: Only one of the TuSyncRef, GpsSyncRef, HptsiSyncRef,
GpsOutSyncLink, gpsOutEnabled and hptsiOutEnabled can be active at
the same time.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TnlQosClass

prefIubUserPlaneTransportOption

RNC

Network Parameters

236 (520)

Defines the preferred Iub user plane transport option.


TransportOptionDef
Only used for the IubLinks for which the dual stack feature has been
configured, and only when the dual stack feature has been activated.
IubLinks that do not have the dual stack feature activated will use the value
of IubLink::userPlaneTransportOption, regardless of the value of this
attribute.
One and only one flag must be set to TRUE.
Takes effect: New connections

TnlQosClass

prefIubUserPlaneTransportOption.atm

RNC

Controls if ATM is enabled in the transport layer.

BooleanVals

TnlQosClass

prefIubUserPlaneTransportOption.ipv4

RNC

Controls if IPv4 is enabled in the transport layer.

BooleanVals

TrafficManagement

featureState

RBS DUW

Specifies if the licensed feature Egress IP Traffic Shaping is ACTIVATED or ActivationVals


DEACTIVATED.

FALSE = 0
TRUE = 1
FALSE = 0
TRUE = 1
ACTIVATED = 1
DEACTIVATED = 0

DEACTIVATED(0)

The feature is not enabled until the feature state is ACTIVATED and there
is a valid Egress IP Traffic Shaping license in the node.
TrafficManagement

featureState

RNC

Specifies if the licensed feature Egress IP Traffic Shaping is ACTIVATED or ActivationVals


DEACTIVATED.

ACTIVATED = 1
DEACTIVATED = 0

DEACTIVATED(0)

The feature is not enabled until the feature state is ACTIVATED and
there is a valid Egress IP Traffic Shaping license in the node.
TrafficManagement

licenseState

RBS DUW

TrafficManagement

licenseState

RNC

TrafficManagement
TrafficManagement
TrafficManagement
TrafficManagement
TrafficManagementQueue

TrafficManagementId
TrafficManagementId
userLabel
userLabel
dropMechanism

RBS DUW
RNC
RBS DUW
RNC
RBS DUW

TrafficManagementQueue

queueLength

RBS DUW

TrafficManagementQueue
TrafficManagementQueue
TrafficManagementQueue

queueOccupancyPackets
queueOccupancyPercentage
queueWeight

RBS DUW
RBS DUW
RBS DUW

Indicates whether a valid license key is installed for the feature Egress IP
Traffic Shaping.
Indicates whether a valid license key is installed for the feature Egress IP
Traffic Shaping.
The value component of the RDN.
The value component of the RDN.
Label for free use.
Label for free use.
Specifies the drop mechanism to be used for the queue.

StateVals

Specifies the maximum depth of each queue in bytes, beyond which all
newly arrived packets will be dropped.

long

ENABLED = 1
DISABLED = 0
ENABLED = 1
DISABLED = 0

StateVals
string
string
string
string
DropMechanism

TAIL_DROP = 0
RED = 1
0..6000000

TAIL_DROP
1024000

Unit: 1 B
Indicates the current number of packets in the queue.
long
Indicates the queue filling level in percentage of the queue length.
long
The minimum guaranteed rate that the scheduler, in case of Weighted
long
Priority Scheduling, must allocate to a queue. This minimum rate is relative
to the average rate of the traffic shaper (configured by attribute egressCir in
the TrafficScheduler MO)

1..100

The sum of queueWeight for all queues belonging to the Weighted Priority
Scheduling group can not exceed 100 and such a configuration will be
rejected.
If the sum of all active queue weights is less than 100, the amount that
each queue gets served by the scheduler, equals to the weight of the
queue plus non-reserved bandwidth divided by the number of queues.
Unit: 1 %

TrafficManagementQueue

Prepared: EZIEAGA

redProperties

RBS DUW

Specifies the parameter values to be used by the Random Early Detection RedProperties
(RED) drop mechanism.

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TrafficManagementQueue

redProperties.redAveragingWeightFactor

RBS DUW

Network Parameters

Specifies the averaging weight factor used by the Random Early Detection long
(RED) drop mechanism when calculating the average queue length. The
averaging weight factor is used as the parameter n in the following formula:

237 (520)
1..8

average_queue_length = old_average_queue_length * (1 - 2^-n) +


current_queue_length * 2^-n, where 2^-n means: 2 raised to the power of
-n.
The averaging weight factor controls the sensitivity to bursts and rapid
changes in the actual queue length. Setting the averaging weight factor too
high causes the average queue length to respond too slowly to changes in
the actual queue size, thus not reacting to congestion. Setting the
averaging weight factor too low causes the average queue length to
respond too fast to changes in the actual queue size, thus overreacting to
bursts and dropping packets unnecessarily.
Guideline: The egress bandwidth, that is, the setting of attribute egressCir
in MO TrafficSchedluer, and the average packet size should influence the
choice of this attribute value.

TrafficManagementQueue

redProperties.redMaxThreshold

RBS DUW

Specifies the maximum threshold used by the Random Early Detection


long
(RED) drop mechanism. If the average queue length calculated by the RED
mechanism, reaches the maximum threshold, packets are dropped with a
probability of 1.

1..100

30

1..100

10

The threshold is specified as a proportion of the maximum queue length


specified in attribute queueLength.
Guideline: The egress bandwidth, that is, the setting of attribute egressCir
in MO TrafficScheduler, and the average packet size should influence the
choice of this attribute value.
Unit: 1 %
TrafficManagementQueue

redProperties.redMinThreshold

RBS DUW

Specifies the minimum threshold used by the Random Early Detection


long
(RED) drop mechanism. If the average queue length calculated by the RED
mechanism, reaches the minimum threshold, packets are started to be
dropped randomly with an increasing probability.
The threshold is specified as a proportion of the maximum queue length
specified in attribute queueLength.
Guideline: The egress bandwidth, that is, the setting of attribute egressCir
in MO TrafficScheduler, and the average packet size should influence the
choice of this attribute value.
This attribute value should be less than or equal to the value of attribute
redMaxThershold.
Unit: 1 %

TrafficManagementQueue
TrafficManagementQueue
TrafficManagementQueue
TrafficScheduler

reservedBy
TrafficManagementQueueId
userLabel
dscpMap

RBS DUW
RBS DUW
RBS DUW
RBS DUW

Contains an MO instance that reserves this MO instance.


The value component of the RDN.
Label for free use.
Maps a queue number (1-8) to each DSCP value (0-63).

ManagedObject
string
string
DscpMap

Default mappings for DSCP -> queue


DSCP 51, 54 -> queue 1
DSCP 24, 32, 34, 36, 38, 40, 46, 48 -> queue 2
DSCP 8, 16, 18, 20, 22, 26, 28 -> queue 3
DSCP 10, 12, 14 -> queue 4
DSCP 0, 1, 2, 3, 4, 5, 6, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 27, 29, 30, 31,
33, 35, 37, 39, 41, 42, 43, 44, 45, 47, 49, 50, 52, 53, 55, 56, 57, 58, 59, 60,
61, 62, 63 -> queue 5

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TrafficScheduler

dscpMap.dscp

RBS DUW

TrafficScheduler

dscpMap.queue

RBS DUW

TrafficScheduler

egressCbs

RBS 6401

TrafficScheduler

egressCbs

RBS DUW

Network Parameters

DSCP value of the IP Packet Header. The number of members in this


long
sequence is 64 (0-63).
Queue number between 1 and 8. The number of members in this sequence long
is 64 (0-63).
The maximum Committed Burst Size (CBS) in number of bytes sent in the int32
egress direction.

238 (520)

2..125

The maximum Committed Burst Size (CBS) in number of bytes sent in the long
egress direction.

An egress Traffic Manager entity is allowed to burst 2 x MTU bytes even if


egressCbs is configured to a value lower than 2 x MTU. The MTU for an
TrafficScheduler MO referenced by one or more IpInterface MOs or
Ipv6Interface MOs, is assumed to be the MTU with the highest value
amongst all IpInterface MOs and Ipv6Interface MOs.
Unit: 1 B
TrafficScheduler

egressCir

RBS 6401

This attribute defines the Committed Information Rate (CIR), that is, the
average rate in Mbps,
used by the traffic shaper on the egress direction of the interface.
If the value is zero (default value), then there is effectively no rate limit.
The lowest configurable value (above zero) is 2 Mbps.

TrafficScheduler

egressCir

RBS DUW

This attribute defines the Committed Information Rate (CIR), that is, the
long
average rate in Mbps, used by the traffic shaper on the egress direction of
the interface. If the value is zero (default value), there is effectively no rate
limit. The lowest configurable value (above zero) is 2 Mbps.

int32

0, 2..1000

0..0 2..1000

0..0 1..100

If the sum of the egressCir values for the TrafficScheduler MOs referenced
by the IpInterface or Ipv6Interface MOs connected to the same physical
interface exceeds the equivalent IP Layer bandwidth of the physical
interface, the shaping characteristics are undefined and are not
deterministic.
This attribute is not applicable when egressCirLow is set to a value different
from zero.
Unit: 1 Mbps

TrafficScheduler

egressCirLow

RBS DUW

Defines the Committed Information Rate (CIR) for low-rate shaping, that is, long
the average rate in units of 100 Kbps, used by the traffic shaper on the
egress direction of the interface.
When set to zero (default value), this attribute is not applicable and
instead, the attribute egressCir defines the CIR.
Low-rate shaping is supported for the following combinations of Committed
Information Rate (CIR) and IP packet lengths:
- For CIRs of 300 kbps and below, low-rate shaping is not supported.
- For a CIR of 400 kbps, low-rate shaping is supported for IP packets with a
maximum length of 450 octets.
- For CIRs of 500 kbps and above, low-rate shaping is supported for IP
packets with a maximum length of 580 octets.
When this attribute is set to a value different from zero, only one instance
of TrafficScheduler MO is allowed.
Unit: 100 Kbps

TrafficScheduler

rbsULPolicingFactor

RBS 6401

Ratio in reference to backhaul data rate to limit RBS data to backhaul


leaving space for WiFi or cascaded pRBSs.

int32

TrafficScheduler
TrafficScheduler

reservedBy
trafficSchedulerId

RBS DUW
RBS 6401

Contains an MO instance that reserves this MO instance.


The value of component RDN.

ManagedObject
string

TrafficScheduler

TrafficSchedulerId

RBS DUW

The value component of the RDN.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

2..10

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

239 (520)

TrafficScheduler

trafficShapingProfile

RBS 6401

Selected profile will define


The Number of queues / queue structure
DSCP-to-queues
Scheduling algorithms (SP vs. DWRR)
Buffer weights for DWWR queues
Queue length per queue with a drop profile either Taildrop or RED

TrafficShapingProfile

PROFILE1 = 0
PROFILE2 = 1
PROFILE3 = 2

PROFILE1(0)

TrafficScheduler
TrafficScheduler

userLabel
wpEndQueue

RBS DUW
RBS DUW

Label for free use.


Specifies the end queue in the Weighted Priority Scheduling group.

string
long

2..8 1000..1000

1000

long

1..8 1000..1000

1000

When the Weighted Priority group is enabled, setting wpEndQueue to a


value that is less or equal to wpStartQueue, is not allowed.
Setting wpEndQueue to a value that is equal or above the number of
queues, disables the Strict Priority 2 group.
TrafficScheduler

wpStartQueue

RBS DUW

Specifies the first queue in the Weighted Priority Scheduling group.


Setting wpStartQueue to a value that is equal or above number of queues,
disables the Weighted Priority group.
Setting wpStartQueue to 1 disables the Strict Priority 1 group.
The value 1000 means that Weighted Priority Scheduling is not used for
any queue.

Transport

transportId

RBS 6401

TransportNetwork

TransportNetworkId

RBS DUW

TransportNetwork

TransportNetworkId

RNC

The value component of the RDN. _x000D_


The allowed character set is defined by 3GPP TS 32.300.
The value component of the RDN.

string
string

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


TransportNetwork
TransportNetwork

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

TuSyncRef

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

TuSyncRef

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

TuSyncRef

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TuSyncRef

availabilityStatus

RNC

The availability status.

Network Parameters

240 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

It contains details about operationalState.

TuSyncRef

operationalState

RBS DUW

The operational state.

OperState

TuSyncRef

operationalState

RNC

The operational state.

OperState

TuSyncRef
TuSyncRef

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

ManagedObject
ManagedObject

TuSyncRef
TuSyncRef

TuSyncRefId
TuSyncRefId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

TuSyncRef
TuSyncRef
TwampResponder

userLabel
userLabel
actualModes

RBS DUW
RNC
RBS DUW

Label for free use.


Label for free use.
Show the twamp modes that are supported by the responder.

string
string
string

TwampResponder

actualModes

RNC

In this release always set to the string "UNAUTHENTICATED"


Show the twamp modes that are supported by the responder.

string

In this release always set to the string ?UNAUTHENTICATED?


TwampResponder

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

When LOCKED, the TWAMP Responder does not respond on incoming


probe packets.
TwampResponder

administrativeState

RNC

The administrative state.


When LOCKED, the TWAMP Responder does not respond on
incoming probe packets.

TwampResponder

availabilityStatus

RBS DUW

The availability status.


It contains details about operationalState.
In addition to this, the value degraded shall be used when the
TwampResponder has reached the maximum number of test sessions.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TwampResponder

availabilityStatus

RNC

Network Parameters

The availability status.

241 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.


In addition to this, the value degraded shall be used when the
TwampResponder has reached the maximum number of test sessions.

TwampResponder
TwampResponder
TwampResponder

ipAccessHostEtRef
ipAccessHostEtRef
operationalState

RBS DUW
RNC
RBS DUW

Reference to an instance of a IpAccessHostEt MO.


Reference to an instance of a IpAccessHostEt MO.
The operational state.

ManagedObject
ManagedObject
OperState

DISABLED = 0
ENABLED = 1

Will be disabled if it receives state changes from the IpAccessHostEt MO.


Will also be disabled if the alarm below is detected and if there is no active
twampresponder license
TwampResponder

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1

Will be disabled if it receives state changes from the


IpAccessHostEt MO.
Will also be disabled if the alarm below is detected and if there is
no active twampresponder license
TwampResponder
TwampResponder
TwampResponder

TwampResponderId
TwampResponderId
udpPort

RBS DUW
RNC
RBS DUW

The value component of the RDN.


The value component of the RDN.
The local UDP port that the TWAMP responder receives TWAMP packets
on.

string
string
long

1..49151

long

1..49151

The port can be configured in range 1-49151 but a number of ports will be
reserved by the system and can not be used.
TwampResponder

udpPort

RNC

The local UDP port that the TWAMP responder receives TWAMP packets
on.
The port can be configured in range 1-49151 but a number of ports
will be reserved by the system and can not be used.

TwampResponder
TwampResponder
UniSaalProfile
UniSaalProfile

userLabel
userLabel
profileData
profileData

RBS DUW
RNC
RBS DUW
RNC

Label for free use.


Label for free use.
The profile data.
The profile data.

string
string
UniSaalProfileData
UniSaalProfileData

UniSaalProfile

profileData.congestionAbatement

RBS DUW

The percentage of the buffer for which congestion is stopped.

long

0..100

30

30

When the current send buffer occupancy for a Termination Point (TP)
decreases below congestionAbatement, a congestion ceased indication is
sent to the user of this TP. If the congestionAbatement level is lesser but
almost equal to congestionOnSet, congestion indications might be raised
and ceased very often.
This attribute must follow the rule, 0 <= congestationAbatement <
congestationOnSet <= 100.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
UniSaalProfile

profileData.congestionAbatement

RNC

Network Parameters

The percentage of the buffer for which congestion is stopped.

242 (520)

long

0..100

30

30

long

0..100

90

90

long

0..100

90

90

long

10..1000

30 See CPI

long

10..1000

30 See CPI

long

0..100

long

0..100

long

10..10000

When the current send buffer occupancy for a Termination Point


(TP) decreases below congestionAbatement, a congestion ceased
indication is sent to the user of this TP. If the congestionAbatement level is
lesser but almost equal to congestionOnSet, congestion indications might
be raised and ceased very often.
This attribute must follow the rule, 0 <= congestationAbatement <
congestationOnSet <= 100.

UniSaalProfile

profileData.congestionOnSet

RBS DUW

The percentage of the buffer that must be filled in order to cause


congestion.
When the current send buffer occupancy for a Termination Point (TP)
increases above congestionOnSet, a congestion indication is sent to the
user of this TP.
The part of the buffer above the congestion level is used to take care of the
messages that were sent before the users stopped the sending.
This attribute must follow the rule, 0 <= congestationAbatement <
congestationOnSet <= 100.

UniSaalProfile

profileData.congestionOnSet

RNC

The percentage of the buffer that must be filled in order to cause


congestion.
When the current send buffer occupancy for a Termination Point
(TP) increases above congestionOnSet, a congestion indication is sent to
the user of this TP.
The part of the buffer above the congestion level is used to take
care of the messages that were sent before the users stopped the sending.
This attribute must follow the rule, 0 <= congestationAbatement <
congestationOnSet <= 100.

UniSaalProfile

profileData.initialCredit

RBS DUW

Initial number of credits.


For 64 kbit/s use 30.
This attribute must follow the rule, initialCredit > maxPD.
Unit: 1 transmitted PDUs

UniSaalProfile

profileData.initialCredit

RNC

Initial number of credits.


For 64 kbit/s use 30.
This attribute must follow the rule, initialCredit > maxPD.
Unit: 1 transmitted PDUs
The maximum number of retransmissions of Protocol Data Units (PDU):
BGN, END, ER, RS.

UniSaalProfile

profileData.maxCC

RBS DUW

UniSaalProfile

profileData.maxCC

RNC

The maximum number of retransmissions of Protocol Data Units (PDU):


BGN, END, ER, RS.

UniSaalProfile

profileData.maxPD

RBS DUW

The maximum number of SD PDUs before a poll is sent.

Unit: 1 transmitted PDUs

Unit: 1 transmitted PDUs


25 See CPI

This attribute must follow the rule, maxPD < initialCredit.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
UniSaalProfile

profileData.maxPD

RNC

Network Parameters

The maximum number of SD PDUs before a poll is sent.

long

243 (520)
10..10000

25 See CPI

3..1001

67

67

3..1001

67

67

This attribute must follow the rule, maxPD < initialCredit.


UniSaalProfile

profileData.maxStat

RBS DUW

The maximum number, odd integer value, of list elements placed in a STAT long
PDU.
The maxStat attribute is controlled by the AAL5 maximum SDU size
defined in the Aal5TpVccTp MO. The maxStat times 4 (octets) plus
additional 12 octets (for header) must not exceed the AAL5 maximum SDU
size (lower of the two directions, fromUserMaxSduSize and
toUserMaxSduSize).
The consistency check is performed when the UniSaalTp MO is created, as
there is no relation between the UniSaalProfile MO and the Aal5TpVccTp
MO.
Unit: 1 transmitted PDUs

UniSaalProfile

profileData.maxStat

RNC

The maximum number, odd integer value, of list elements placed in a STAT long
PDU.
The maxStat attribute is controlled by the AAL5 maximum SDU size
defined in the Aal5TpVccTp MO. The maxStat times 4 (octets) plus
additional 12 octets (for header) must not exceed the AAL5 maximum SDU
size (lower of the two directions, fromUserMaxSduSize and
toUserMaxSduSize).
The consistency check is performed when the UniSaalTp MO is
created, as there is no relation between the UniSaalProfile MO and the
Aal5TpVccTp MO.
Unit: 1 transmitted PDUs

UniSaalProfile

profileData.timerCC

RBS DUW

The timer determining the time between retransmission of PDUs: BGN,


END, ER, RS.

long

10..10000

1000

1000

long

10..10000

1000

1000

1000..600000

2000

2000

1000..600000

2000

2000

It should be more than the roundtrip delay.


Unit: 1 ms
UniSaalProfile

profileData.timerCC

RNC

The timer determining the time between retransmission of PDUs: BGN,


END, ER, RS.
It should be more than the roundtrip delay.
Unit: 1 ms

UniSaalProfile

profileData.timerIdle

RBS DUW

The timer running when there are no PDUs to transmit and there are no
long
outstanding acknowledgements or data pending for credit. When this timer
is running, no POLL PDUs are sent.
This timer should be significantly greater than the value of timerKeepAlive.
Unit: 1 ms

UniSaalProfile

profileData.timerIdle

RNC

The timer running when there are no PDUs to transmit and there are no
long
outstanding acknowledgements or data pending for credit. When this timer
is running, no POLL PDUs are sent.
This timer should be significantly greater than the value of
timerKeepAlive.
Unit: 1 ms

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

UniSaalProfile

profileData.timerKeepAlive

RBS DUW

The timer to be used during a period of no outstanding acknowledgements long


or new data pending receipt of credit. At timeout, the peer is polled to see if
it is alive. The timer determines the interval between polls in the transient
phase. This timer should be greater than the roundtrip delay and also
greater than timerPoll.

UniSaalProfile

profileData.timerKeepAlive

RNC

The timer to be used during a period of no outstanding acknowledgements long


or new data pending receipt of credit. At timeout, the peer is polled to see if
it is alive. The timer determines the interval between polls in the transient
phase. This timer should be greater than the roundtrip delay and also
greater than timerPoll.

UniSaalProfile

profileData.timerNoResponse

RBS DUW

The timer to determine the maximum time interval, during which reception
of at least one STAT PDU is expected as a response to a poll.

244 (520)
10..10000

500

500

10..10000

500

500

long

10..100000

4000

4000

long

10..100000

4000

4000

long

10..100000

100

100

long

10..100000

100

100

Unit: 1 ms

Unit: 1 ms

This attribute must follow the rule, timerNoResponse >= timerKeepAlive +


one roundtrip delay
Unit: 1 ms
UniSaalProfile

profileData.timerNoResponse

RNC

The timer to determine the maximum time interval, during which reception
of at least one STAT PDU is expected as a response to a poll.
This attribute must follow the rule, timerNoResponse >=
timerKeepAlive + one roundtrip delay
Unit: 1 ms
The timer that specifies the maximum time between sending of POLL
PDUs to the peer receiver during other traffic (active phase).

UniSaalProfile

profileData.timerPoll

RBS DUW

UniSaalProfile

profileData.timerPoll

RNC

The timer that specifies the maximum time between sending of POLL
PDUs to the peer receiver during other traffic (active phase).

UniSaalProfile
UniSaalProfile

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

UniSaalTp
UniSaalTp

UniSaalProfile
UniSaalProfile

UniSaalProfileId
UniSaalProfileId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

UniSaalProfile
UniSaalProfile

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

UniSaalTp

aal5TpVccTpId

RBS DUW

Contains a reference to an Aal5TpVccTp MO instance.

Aal5TpVccTp

UniSaalTp

aal5TpVccTpId

RNC

Unit: 1 ms

Unit: 1 ms

The AAL5 termination point must terminate on a main processor, MP.


Contains a reference to an Aal5TpVccTp MO instance.

Aal5TpVccTp

The AAL5 termination point must terminate on a main processor,


MP.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
UniSaalTp

maxSduSize

RBS DUW

Network Parameters

Maximum SAAL SDU size.

245 (520)

long

128..2044

128 Q.2630: 128


NBAP-C: 2044
NBAP-D: 1024

long

128..2044

128 Q.2630: 128


NBAP-C: 2044
NBAP-D: 1024

When setting the value of maxSduSize the 4 bytes used by the SAAL layer
for the SAAL header has to be considered.
Example: If fromUserMaxSduSize is set to 256 and toUserMaxSduSize is
set to 512 in the Aal5TpVccTp MO, the maxSduSize may not exceed 252.
(maxSduSize <= the UserMaxSduSize from Aal5TpVccTp MO - 4 bytes)
The upper limit of 2044 (2048 including the SAAL header) is due to
limitations on the AAL5 layer.
Unit: 1 B
Dependencies: This attribute may not exceed the value of the AAL5
maximum SDU size defined in the Aal5TpVccTp MO, that is the lower value
of the two directions, fromUserMaxSduSize and toUserMaxSduSize.

UniSaalTp

maxSduSize

RNC

Maximum SAAL SDU size.


When setting the value of maxSduSize the 4 bytes used by the
SAAL layer for the SAAL header has to be considered.
Example: If fromUserMaxSduSize is set to 256 and
toUserMaxSduSize is set to 512 in the Aal5TpVccTp MO, the maxSduSize
may not exceed 252.
(maxSduSize <= the UserMaxSduSize from Aal5TpVccTp MO - 4
bytes)
The upper limit of 2044 (2048 including the SAAL header) is due to
limitations on the AAL5 layer.
Unit: 1 B
Dependencies: This attribute may not exceed the value of the AAL5
maximum SDU size defined in the Aal5TpVccTp MO, that is the lower value
of the two directions, fromUserMaxSduSize and toUserMaxSduSize.

UniSaalTp

operationalState

RBS DUW

The operational state.

OperState

UniSaalTp

operationalState

RNC

The operational state.

OperState

UniSaalTp
UniSaalTp

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserves this MO instance.


Contains an MO instance that reserves this MO instance.

ManagedObject
ManagedObject

UniSaalTp

uniSaalProfileId

RBS DUW

Contains a reference to an UniSaalProfile MO.

UniSaalProfile

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

Dependencies: The maxStat attribute defined in the struct


UniSaalProfileData of UniSaalProfile MO is dependent on the AAL5 SDU
size defined in the Aal5TpVccTp MO.
UniSaalTp

uniSaalProfileId

RNC

Contains a reference to an UniSaalProfile MO.

UniSaalProfile

Dependencies: The maxStat attribute defined in the struct


UniSaalProfileData of UniSaalProfile MO is dependent on the AAL5 SDU
size defined in the Aal5TpVccTp MO.
UniSaalTp
UniSaalTp

UniSaalTpId
UniSaalTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

UniSaalTp
UniSaalTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

246 (520)

UpgradePackage

hsiVariant

RBS DUW

Defines the type of HwSensitive that is used i.e. load module files for
HsiVariant
configured boards will be/are installed (HSI), or that all load module files for
matching node type will be/are installed.

HSI = 0
NSI = 1
NOT_VALID = 2
UNDEFINED = 3

UpgradePackage

preUpgradeState

RBS DUW

Specifies the pre-upgrade state during an upgrade procedure.

SuPreUpgradeState

NOT_PRE_UPGRADED = 0
PRE_UPGRADE_EXECUTING = 1
PRE_UPGRADE_COMPLETED = 2
RESTORE_SU_EXECUTING = 3

Vc11Ttp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Vc11Ttp

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Vc11Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

The attribute can be set only if there are no DS0 bundles connected to
handling groups that are carried within this VC11 frame.
The attribute can be set only if there are no DS0 bundles connected to
handling groups that are carried within this VC11 frame.

HgTsAllocation

DISTRIBUTED = 1
CONCENTRATED = 2
DISTRIBUTED = 1
CONCENTRATED = 2

It contains details about operationalState.

Vc11Ttp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Vc11Ttp

hgTsAllocation

RBS DUW

Vc11Ttp

hgTsAllocation

RNC

Vc11Ttp

operationalState

RBS DUW

The operational state.

OperState

Vc11Ttp

operationalState

RNC

The operational state.

OperState

Vc11Ttp

shutDownTimeout

RBS DUW

The shut-down timer.

long

HgTsAllocation

DISTRIBUTED(1) DISTRIBUTED(1)
DISTRIBUTED(1) DISTRIBUTED(1)

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc11Ttp

shutDownTimeout

RNC

Network Parameters

The shut-down timer.

long

247 (520)
0..100000

1800

It is used when the administrativeState is set to


SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s
Vc11Ttp

tuAisReporting

RBS DUW

Indicates whether the alarm Timing Unit 11 (TU11) Alarm Indication Signal
(AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc11Ttp

tuAisReporting

RNC

Indicates whether the alarm Timing Unit 11 (TU11) Alarm Indication Signal
(AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc11Ttp
Vc11Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Vc11Ttp

Vc11TtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.


Vc11Ttp

Vc11TtpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.


Vc11Ttp

vcDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc11Ttp

vcDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc11Ttp

vcDegThreshold

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc11Ttp

vcDegThreshold

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc11Ttp

vcRdiReporting

RBS DUW

Indicates whether the alarm VC11 Remote Defect Indication (RDI) is to be boolean
issued.

Unit: 1 %

Unit: 1 %
0

true - reporting enabled.


false - reporting disabled.
Vc11Ttp

vcRdiReporting

RNC

Indicates whether the alarm VC11 Remote Defect Indication (RDI) is to be boolean
issued.
true - reporting enabled.
false - reporting disabled.

Vc12Ttp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Vc12Ttp

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc12Ttp

availabilityStatus

RBS DUW

Network Parameters

The availability status.

248 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Vc12Ttp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Vc12Ttp

expectedPathTrace

RBS DUW

The expected path trace.

string

The string can be of a maximum of 15 characters in length, or an empty


string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of the characters "0" to "9", "A" to "Z" or "a" to "z". A
CRC-7 is added automatically at the beginning of the string.
An empty string for this attribute means that the detection of Trace
Identifier Mismatch (TIM) is disabled. This attribute is set to empty string
every time attribute pathTraceFormat is set.
Vc12Ttp

expectedPathTrace

RNC

The expected path trace.

string

The string can be of a maximum of 15 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of the characters ?0? to ?9?, ?A? to ?Z? or ?
a? to ?z?. A CRC-7 is added automatically at the beginning of the string.
An empty string for this attribute means that the detection of Trace
Identifier Mismatch (TIM) is disabled. This attribute is set to empty string
every time attribute pathTraceFormat is set.

Vc12Ttp

operationalState

RBS DUW

The operational state.

OperState

Vc12Ttp

operationalState

RNC

The operational state.

OperState

Vc12Ttp

shutDownTimeout

RBS DUW

The shut-down timer.

long

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
0..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc12Ttp

shutDownTimeout

RNC

Network Parameters

The shut-down timer.

long

249 (520)
0..100000

1800

It is used when the administrativeState is set to


SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s
Vc12Ttp

timConsequentAction

RBS DUW

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.

true - enabled.
false - disabled.
Vc12Ttp

timConsequentAction

RNC

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.
true - enabled.
false - disabled.

Vc12Ttp

transmittedPathTrace

RBS DUW

The transmitted path trace.

string

The string can be a maximum of 15 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string consists of the characters "A - Z", "a - z", or "0 - 9". A CRC-7 is
added automatically at the beginning of the string.
No check is performed on the characters specified in the string.
Vc12Ttp

transmittedPathTrace

RNC

The transmitted path trace.

string

The string can be a maximum of 15 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string consists of the characters "A - Z", "a - z", or "0 - 9". A
CRC-7 is added automatically at the beginning of the string.
No check is performed on the characters specified in the string.

Vc12Ttp

tuAisReporting

RBS DUW

Indicates whether the alarm Timing Unit 12 (TU12) Alarm Indication Signal boolean
(AIS) is to be issued.

true - enable reporting.


false - disable reporting.
Vc12Ttp

tuAisReporting

RNC

Indicates whether the alarm Timing Unit 12 (TU12) Alarm Indication Signal boolean
(AIS) is to be issued.
true - enable reporting.
false - disable reporting.

Vc12Ttp
Vc12Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Vc12Ttp

Vc12TtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc12Ttp

Vc12TtpId

RNC

Network Parameters

The value component of the RDN.

250 (520)

string

It is set automatically when the MO instance is created.


Vc12Ttp

vcDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc12Ttp

vcDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc12Ttp

vcDegThreshold

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc12Ttp

vcDegThreshold

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc12Ttp

vcRdiReporting

RBS DUW

Indicates whether the alarm VC12 Remote Defect Indication (RDI) is to be boolean
issued.

Unit: 1 %

Unit: 1 %
0

true - reporting enabled.


false - reporting disabled.
Vc12Ttp

vcRdiReporting

RNC

Indicates whether the alarm VC12 Remote Defect Indication (RDI) is to be boolean
issued.
true - reporting enabled.
false - reporting disabled.

Vc3Ttp

auAisReporting

RBS DUW

Indicates whether the alarm Administrative Unit (AU3) Alarm Indication


Signal (AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc3Ttp

auAisReporting

RNC

Indicates whether the alarm Administrative Unit (AU3) Alarm Indication


Signal (AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc3Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc3Ttp

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

Vc3Ttp

expectedPathTrace

RBS DUW

The expected path trace.

251 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
An empty string means that the detection of Trace Identifier Mismatch
(TIM) is disabled. This attribute is set to an empty string every time the
attribute pathTraceFormat is set.
Vc3Ttp

expectedPathTrace

RNC

The expected path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
An empty string means that the detection of Trace Identifier
Mismatch (TIM) is disabled. This attribute is set to an empty string every
time the attribute pathTraceFormat is set.

Vc3Ttp

operationalState

RBS DUW

The operational state.

OperState

Vc3Ttp

operationalState

RNC

The operational state.

OperState

Vc3Ttp

pathTraceFormat

RBS DUW

Indicates the format of the attributes, expectedPathtrace and


transmittedPathtrace. The format may be in 16 or 64 characters. Usually,
16 is used for ETSI and 64 for ANSI/TTC.

PathTraceFormat

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
ITU_T_G707 = 16
GR_253_CORE = 64

ITU_T_G707(16)

ITU_T_G707=16
GR_253_CORE=64
The 16-character format requires that 15 characters are specified, where
no character is the null character. (The 16th character is added
automatically.)
The 64-character format requires that 62 characters are specifed, where no
character is the null character. (Carriage return and line feed are added
automatically.)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc3Ttp

pathTraceFormat

RNC

Network Parameters

Indicates the format of the attributes, expectedPathtrace and


transmittedPathtrace. The format may be in 16 or 64 characters. Usually,
16 is used for ETSI and 64 for ANSI/TTC.

252 (520)

PathTraceFormat

ITU_T_G707 = 16
GR_253_CORE = 64

ITU_T_G707(16)

ITU_T_G707=16
GR_253_CORE=64
The 16-character format requires that 15 characters are specified,
where no character is the null character. (The 16th character is added
automatically.)
The 64-character format requires that 62 characters are specifed,
where no character is the null character. (Carriage return and line feed are
added automatically.)

Vc3Ttp

timConsequentAction

RBS DUW

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.

true - enabled.
false - disabled.
Vc3Ttp

timConsequentAction

RNC

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.
true - enabled.
false - disabled.

Vc3Ttp

transmittedPathTrace

RBS DUW

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an empty string


(""). A non-empty string not being of full length is padded automatically with
NULL characters.
The string can consist of printable ASCII characters. CR and LF are added
automatically at the end of the string.
Vc3Ttp

transmittedPathTrace

RNC

The transmitted path trace.

string

The string can be a maximum of 62 characters in length, or an


empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
The string can consist of printable ASCII characters. CR and LF are
added automatically at the end of the string.
Vc3Ttp
Vc3Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Vc3Ttp

Vc3TtpId

RBS DUW

The value component of the RDN.

string

Vc3Ttp

Vc3TtpId

RNC

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


Vc3Ttp

vcDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc3Ttp

vcDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Vc3Ttp

vcDegThreshold

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

Vc3Ttp

vcDegThreshold

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

Vc3Ttp

vcRdiReporting

RBS DUW

Indicates whether the alarm VC3 Remote Defect Indication (RDI) is to be


issued.

253 (520)

long

0..100

30

long

0..100

30

Unit: 1 %

Unit: 1 %
boolean

true - enable reporting.


false - disable reporting.
Vc3Ttp

vcRdiReporting

RNC

Indicates whether the alarm VC3 Remote Defect Indication (RDI) is to be


issued.

boolean

true - enable reporting.


false - disable reporting.
Vc4Ttp

auAisReporting

RBS DUW

Indicates whether the alarm Administrative Unit (AU4) Alarm Indication


Signal (AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc4Ttp

auAisReporting

RNC

Indicates whether the alarm Administrative Unit (AU4) Alarm Indication


Signal (AIS) is to be issued.

boolean

true - enable reporting.


false - disable reporting.
Vc4Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Vc4Ttp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc4Ttp

expectedPathTrace

RBS DUW

Network Parameters

The expected path trace.

254 (520)

string

Can be defined in either 16-character format for ETSI, or 64-character


format for TTC.
The string can be a maximum of 15 or 62 characters in length, or an empty
string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
A 15-character string can consist of the characters "A - Z", "a - z", or "0 - 9".
A CRC-7 is added automatically at the beginning of the string.
A 62-character string can consist of printable ASCII characters. CR and LF
are added automatically at the end of the string.
An empty string for this attribute means that the detection of Trace
Identifier Mismatch (TIM) is disabled. This attribute is set to empty string
every time attribute pathTraceFormat is set.
Vc4Ttp

expectedPathTrace

RNC

The expected path trace.

string

Can be defined in either 16-character format for ETSI, or 64character format for TTC.
The string can be a maximum of 15 or 62 characters in length, or
an empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
A 15-character string can consist of the characters "A - Z", "a - z", or
"0 - 9". A CRC-7 is added automatically at the beginning of the string.
A 62-character string can consist of printable ASCII characters. CR
and LF are added automatically at the end of the string.
An empty string for this attribute means that the detection of Trace
Identifier Mismatch (TIM) is disabled. This attribute is set to empty string
every time attribute pathTraceFormat is set.

Vc4Ttp

operationalState

RBS DUW

The operational state.

OperState

Vc4Ttp

operationalState

RNC

The operational state.

OperState

Vc4Ttp

pathTraceFormat

RBS DUW

Indicates the format of the attributes, expectedPathtrace and


transmittedPathtrace. The format may be in 16 or 64 characters. Usually,
16 is used for ETSI and 64 for ANSI/TTC.

PathTraceFormat

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1
ITU_T_G707 = 16
GR_253_CORE = 64

ITU_T_G707(16)

ITU_T_G707=16
GR_253_CORE=64
The 16-character format requires that 15 characters are specified, where
no character is the null character.
(The 16th character is added automatically.)
The 64-character format requires that 62 characters are specifed, where no
character is the null character.
(Carriage return and line feed are added automatically.)

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Vc4Ttp

pathTraceFormat

RNC

Network Parameters

Indicates the format of the attributes, expectedPathtrace and


transmittedPathtrace. The format may be in 16 or 64 characters. Usually,
16 is used for ETSI and 64 for ANSI/TTC.

PathTraceFormat

255 (520)
ITU_T_G707 = 16
GR_253_CORE = 64

ITU_T_G707(16)

ITU_T_G707=16
GR_253_CORE=64
The 16-character format requires that 15 characters are specified,
where no character is the null character.
(The 16th character is added automatically.)
The 64-character format requires that 62 characters are specifed,
where no character is the null character.
(Carriage return and line feed are added automatically.)

Vc4Ttp
Vc4Ttp

reservedBy
reservedBy

RBS DUW
RNC

Contains a list of MO instances that reserve this MO instance.


Contains a list of MO instances that reserve this MO instance.

AtmPort
AtmPort

Vc4Ttp

timConsequentAction

RBS DUW

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.

true - enabled.
false - disabled.
Vc4Ttp

timConsequentAction

RNC

Trace Identifier Mismatch (TIM) consequent action, that is for generation of boolean
Alarm Indication Signal (AIS) downstream and Remote Defect Indication
(RDI) upstream as a consequence of the TIM detection.
true - enabled.
false - disabled.

Vc4Ttp

transmittedPathTrace

RBS DUW

The transmitted path trace.

string

Can be defined in either 16-character format for ETSI or 64-character


format for TTC.
The string can be a maximum of 15 or 62 characters in length, or an empty
string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
A 15-character string can consist of the characters "0" to "9", "A" to "Z" or
"a" to "z". A CRC-7 is added automatically at the beginning of the string.
A 62-character string can consist of printable ASCII characters. CR and LF
are added automatically at the end of the string.

Vc4Ttp

transmittedPathTrace

RNC

The transmitted path trace.

string

Can be defined in either 16-character format for ETSI or 64character format for TTC.
The string can be a maximum of 15 or 62 characters in length, or
an empty string (""). A non-empty string not being of full length is padded
automatically with NULL characters.
A 15-character string can consist of the characters ?0? to ?9?, ?A?
to ?Z? or ?a? to ?z?. A CRC-7 is added automatically at the beginning of
the string.
A 62-character string can consist of printable ASCII characters. CR
and LF are added automatically at the end of the string.

Vc4Ttp

Prepared: EZIEAGA

userLabel

RBS DUW

Label for free use.

string

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Vc4Ttp

userLabel

RNC

Label for free use.

string

Vc4Ttp

Vc4TtpId

RBS DUW

The value component of the RDN.

string

Vc4Ttp

Vc4TtpId

RNC

256 (520)

It is set automatically when the MO instance is created.


The value component of the RDN.

string

It is set automatically when the MO instance is created.


Vc4Ttp

vcDegM

RBS DUW

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc4Ttp

vcDegM

RNC

The number of bad seconds in a row that causes a Degraded Signal alarm. long

2..10

Vc4Ttp

vcDegThreshold

RBS DUW

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc4Ttp

vcDegThreshold

RNC

Specifies how many of the received blocks are allowed to have bit errors.
The measurement is made each second. If the threshold is exceeded, the
second is considered to be bad.

long

0..100

30

Vc4Ttp

vcRdiReporting

RBS DUW

Indicates whether the alarm VC4 Remote Defect Indication (RDI) is to be


issued.

Unit: 1 %

Unit: 1 %
boolean

true - enable reporting.


false - disable reporting.
Vc4Ttp

vcRdiReporting

RNC

Indicates whether the alarm VC4 Remote Defect Indication (RDI) is to be


issued.

boolean

true - enable reporting.


false - disable reporting.
VclTp

atmTrafficDescriptorId

RBS DUW

Reference to an instance of AtmTrafficDescriptor MO.

AtmTrafficDescriptor

If this reference is set to an new AtmTrafficDescriptor and the VclTp is


linked to (reserved by) an Aal2PathVccTp, the Aal2PathVccTp must be
locked in order to allow other than bandwidth changes.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.
VclTp

atmTrafficDescriptorId

RNC

Reference to an instance of AtmTrafficDescriptor MO.

AtmTrafficDescriptor

If this reference is set to an new AtmTrafficDescriptor and the VclTp


is linked to (reserved by) an Aal2PathVccTp, the Aal2PathVccTp must be
locked in order to allow other than bandwidth changes.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
VclTp

availabilityStatus

RBS DUW

Network Parameters

The availability status.

257 (520)

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

VclTp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

VclTp

counterActivation

RBS DUW

Indicates whether PM counters of type PDF are activated for this MO


instance, when a performance monitoring is created from the PMS
interface.

boolean

If true, and if included in an active performance monitoring, this attribute


activates the PDF counters.
If false, the PDF counters are not active, even when included in an active
performance monitoring.
VclTp

counterActivation

RNC

Indicates whether PM counters of type PDF are activated for this MO


instance, when a performance monitoring is created from the PMS
interface.

boolean

If true, and if included in an active performance monitoring, this


attribute activates the PDF counters.
If false, the PDF counters are not active, even when included in an
active performance monitoring.

VclTp

externalVci

RBS DUW

VclTp

externalVci

RNC

Virtual Channel Identifier (VCI)

long

32..65535

long

32..65535

The identifier for this Virtual Channel Link (VCL).


Virtual Channel Identifier (VCI)
The identifier for this Virtual Channel Link (VCL).
VclTp

operationalState

RBS DUW

The operational state.

OperState

VclTp

operationalState

RNC

The operational state.

OperState

VclTp
VclTp

reservedBy
reservedBy

RBS DUW
RNC

Contains an MO instance that reserve this MO instance.


Contains an MO instance that reserve this MO instance.

ManagedObject
ManagedObject

VclTp

userLabel

RBS DUW

Label for free use.

string

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

VclTp

userLabel

RNC

Label for free use.

string

VclTp
VclTp

VclTpId
VclTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Vlan

reservedBy

RNC

Contains a list of MO instances that reserve this MO instance.

ManagedObject

Vlan

userLabel

RNC

Label for free use.

string

Vlan

vid

RNC

The VLAN Identifier.

long

258 (520)

1..4094

Each value within the specified value range can be used by only
one VLAN instance.
Disturbances: Changing this attribute may cause traffic
disturbances.
Vlan

VlanId

RNC

The value component of the RDN.

string

Vlan

vlanType

RNC

The type of the VLAN.

VlanType

Only one VLAN instance can be configured with vlanType set to


INTERNAL_IP_TRANSPORT.

EXTERNAL = 0
INTERNAL_IP_TRANSPORT = 1
BOARD_INTERNAL = 2

EXTERNAL(0)

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

ALARM_LOC(2)

ALARM_LOC(2)

Only one VLAN instance can be configured with vlanType set to


BOARD_INTERNAL.
VlanPort
VlanPort
VlanPort

encapsulation
userLabel
vlanId

RBS 6401
RBS 6401
RBS 6401

The underlying encapsulation.


ManagedObject
Label for free use.
string
Specifies the VLAN ID for the VlanPort. _x000D_
VlanId
_x000D_
At egress, it's to indicate the VLAN ID in the VLAN tag of the packets being
transmitted out of an EthernetPort.

VlanPort
VpcTp

vlanPortId
alarmReport

RBS 6401
RBS DUW

Value component of the RDN.


Specifies what type of alarms are reported.

string
AlarmReport

VpcTp

alarmReport

RNC

Specifies what type of alarms are reported.

AlarmReport

ALARM_LOC = 2
ALARM_LOC_RDI = 3
ALARM_AIS_LOC = 6
ALARM_AIS_RDI_LOC = 7

VpcTp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

1..4092

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
VpcTp

availabilityStatus

RNC

Network Parameters

The availability status.

AvailabilityStatus

It contains details about operationalState.

VpcTp

continuityCheck

RBS DUW

Specifies whether VP end-to-end continuity check is active.

259 (520)
NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

boolean

Continuity Checking (CC) means that a cell is sent downstream when no


user cell has been sent for a period of nominally 1 second. The continuity
check both enables generation of CC cells as well as detection of LOC.
Activation/Deactivation shall be done on both ends of a VPC via
management terminal.
Specification: ITU.T rec I.610.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

VpcTp

continuityCheck

RNC

Specifies whether VP end-to-end continuity check is active.

boolean

Continuity Checking (CC) means that a cell is sent downstream


when no user cell has been sent for a period of nominally 1 second. The
continuity check both enables generation of CC cells as well as detection of
LOC.
Activation/Deactivation shall be done on both ends of a VPC via
management terminal.
Specification: ITU.T rec I.610.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.
VpcTp

counterMode

RBS DUW

PM mode is set to indicate the type of performance monitoring mode (that


is, activation of bidirectional PM measurements).

AtmCounterMode

PM_MODE_OFF = 0
PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_OFF(0
)

VpcTp

counterMode

RNC

PM mode is set to indicate the type of performance monitoring mode (that


is, activation of bidirectional PM measurements).

AtmCounterMode

PM_MODE_OFF = 0
PM_MODE_ONLYCOUNT = 1
PM_MODE_FPM = 2
PM_MODE_BR = 4
PM_MODE_FPM_BR = 6

PM_MODE_OFF(0
)

VpcTp

nomPmBlkSize

RBS DUW

Nominal performance monitoring (PM) blocksize. The minimum number of AtmNomPmBlkSize


ATM cells to send before sending a Forward Performance Monitoring
(FPM) cell.
Disturbances: Changing lower layer attributes may affect O&M connectivity,
if they are part of the O&M connection.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

260 (520)

VpcTp

nomPmBlkSize

RNC

Nominal performance monitoring (PM) blocksize. The minimum number of AtmNomPmBlkSize


ATM cells to send before sending a Forward Performance Monitoring
(FPM) cell.
Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

NOM_PM_BLKSIZE_2_7 = 128
NOM_PM_BLKSIZ
NOM_PM_BLKSIZE_2_8 = 256
E_2_10(1024)
NOM_PM_BLKSIZE_2_9 = 512
NOM_PM_BLKSIZE_2_10 = 1024
NOM_PM_BLKSIZE_2_11 = 2048
NOM_PM_BLKSIZE_2_12 = 4096
NOM_PM_BLKSIZE_2_13 = 8192
NOM_PM_BLKSIZE_2_14 = 16384
NOM_PM_BLKSIZE_2_15 = 32768

VpcTp

operationalState

RBS DUW

The operational state.

OperState

VpcTp

operationalState

RNC

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

VpcTp
VpcTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

VpcTp
VpcTp

VpcTpId
VpcTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

VplTp

atmTrafficDescriptor

RBS DUW

Reference to an instance of AtmTrafficDescriptor MO.

AtmTrafficDescriptor

See CPI

AtmTrafficDescriptor

See CPI

Disturbances: Changing lower layer attributes may affect O&M connectivity,


if they are part of the O&M connection.
VplTp

atmTrafficDescriptor

RNC

Reference to an instance of AtmTrafficDescriptor MO.


Disturbances: Changing lower layer attributes may affect O&M
connectivity, if they are part of the O&M connection.

VplTp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

It contains details about operationalState.

VplTp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

VplTp

externalVpi

RBS DUW

Virtual Path Identifier (VPI)

long

0..255

The identifier for this Virtual Path Link (VPL).

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
VplTp

externalVpi

RNC

Virtual Path Identifier (VPI)

Network Parameters
long

261 (520)
0..255

The identifier for this Virtual Path Link (VPL).


VplTp

operationalState

RBS DUW

The operational state.

OperState

DISABLED = 0
ENABLED = 1
DISABLED = 0
ENABLED = 1

VplTp

operationalState

RNC

The operational state.

OperState

VplTp
VplTp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

VplTp
VplTp

VplTpId
VplTpId

RBS DUW
RNC

The value component of the RDN.


The value component of the RDN.

string
string

Vt15Ttp

administrativeState

RBS DUW

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Vt15Ttp

administrativeState

RNC

The administrative state.

AdmState

LOCKED = 0
UNLOCKED = 1
SHUTTING_DOWN = 2

LOCKED(0)

Vt15Ttp

aisVreporting

RBS DUW

Indicates whether the alarm Alarm Indication Signal - V (AIS-V) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Vt15Ttp

aisVreporting

RNC

Indicates whether the alarm Alarm Indication Signal - V (AIS-V) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Vt15Ttp

availabilityStatus

RBS DUW

The availability status.

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

AvailabilityStatus

NO_STATUS = 0
IN_TEST = 1
FAILED = 2
POWER_OFF = 4
OFF_LINE = 8
OFF_DUTY = 16
DEGRADED = 64
NOT_INSTALLED = 128
LOG_FULL = 256
DEPENDENCY_LOCKED = 544
DEPENDENCY_FAILED = 1056
DEPENDENCY_SHUTTINGDOWN
= 2080

OperState

DISABLED = 0
ENABLED = 1

It contains details about operationalState.

Vt15Ttp

availabilityStatus

RNC

The availability status.


It contains details about operationalState.

Vt15Ttp

Prepared: EZIEAGA

operationalState

RBS DUW

The operational state.

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Vt15Ttp

operationalState

RNC

The operational state.

OperState

Vt15Ttp

rdiVreporting

RBS DUW

Indicates whether the alarm Remote Defect Indication - V (RDI-V) is to be


issued.

boolean

262 (520)
DISABLED = 0
ENABLED = 1
0

true - reporting enabled.


false - reporting disabled.
Vt15Ttp

rdiVreporting

RNC

Indicates whether the alarm Remote Defect Indication - V (RDI-V) is to be


issued.

boolean

true - reporting enabled.


false - reporting disabled.
Vt15Ttp

shutDownTimer

RBS DUW

The shut-down timer.

long

1..100000

1800

long

1..100000

1800

It is used when the administrativeState is set to SHUTTING_DOWN. When


the timer expires, administrativeState is set to LOCKED.
Unit: 1 s
Vt15Ttp

shutDownTimer

RNC

The shut-down timer.


It is used when the administrativeState is set to
SHUTTING_DOWN. When the timer expires, administrativeState is set to
LOCKED.
Unit: 1 s

Vt15Ttp
Vt15Ttp

userLabel
userLabel

RBS DUW
RNC

Label for free use.


Label for free use.

string
string

Vt15Ttp

Vt15TtpId

RBS DUW

The value component of the RDN.

string

It is set automatically when the MO instance is created.


Vt15Ttp

Vt15TtpId

RNC

The value component of the RDN.

string

It is set automatically when the MO instance is created.

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

263 (520)

Initial Parameter Value Source CPI Reference


TND
TND

Access
Restricted
Restricted

Mandatory
Y
Y

Persistent
Y
Y

Notification
N
N

Sequence
N
N

BulkCM MO Class Name


vsDataAal1TpVccTp
vsDataAal1TpVccTp

BulkCM Parameter Name


id
id

Functional Area
TN Administration
TN Administration

Parameter Group
Id
Id

TND O&M

Read/Write

vsDataAal1TpVccTp

alarmReport

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal1TpVccTp

alarmReport

ATM Connection

EnumRef

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal1TpVccTp

cdvt

ATM Connection

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal1TpVccTp

cdvt

ATM Connection

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

264 (520)

TND O&M

Read/Write

vsDataAal1TpVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal1TpVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal1TpVccTp

counterActivation

TN PM Counters

Real

TND O&M

Read/Write

vsDataAal1TpVccTp

counterActivation

O&M PM Statistics

Real

TND O&M

Read/Write

vsDataAal1TpVccTp

counterMode

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal1TpVccTp

counterMode

O&M PM Statistics

EnumRef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal1TpVccTp
vsDataAal1TpVccTp

ds0BundleId
ds0BundleId

ATM Connection
ATM Connection

Id
MORef

Read/Write

vsDataAal1TpVccTp

nomPmBlockSize

ATM Connection

EnumRef

TND
TND
TND O&M

Prepared: EZIEAGA

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND O&M

Read/Write

vsDataAal1TpVccTp

N/A

Read

N/A

Read

Default

Restricted

vsDataAal1TpVccTp

Default

Restricted

Read/Write
Read/Write

N
N

Y
Y

Y
Y

nomPmBlockSize

265 (520)
ATM Connection

EnumRef

TN Administration

EnumRef

TN Administration

EnumRef

partialFill

ATM Connection

Real

vsDataAal1TpVccTp

partialFill

ATM Connection

Real

N
N

vsDataAal1TpVccTp
vsDataAal1TpVccTp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Read/Write
Read/Write

Y
Y

Y
Y

Y
Y

N
N

vsDataAal1TpVccTp
vsDataAal1TpVccTp

vclTpId
vclTpId

ATM Connection
ATM Connection

Id
MORef

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2Ap
vsDataAal2Ap

id
id

TN Administration
TN Administration

Id
Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

aal2QoSCodePointProfileId

Connection Control

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

266 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

aal2QoSCodePointProfileId

Connection Control

MORef

Default

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

allocationMode

Connection Control

EnumRef

Recommended

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

allocationMode

Connection Control

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

267 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Read
Read

N
N

Y
Y

Y
Y

N
N

Connection Control
Connection Control

Real
Real

Read

Connection Control

Real

Read

Connection Control

Real

Read

Connection Control

Real

Read

Connection Control

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

Y
Y

Y
Y

TN Administration
TN Administration

MORef
MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

268 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

rpuId

Connection Control

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

rpuId

Connection Control

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

secondarySigLinkId

Connection Control

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Ap

secondarySigLinkId

Connection Control

MORef

TND

1/1553-HSD 101 02/7

Restricted

vsDataAal2Ap

sigLinkId

Connection Control

Id

TND

1/1553-HSD 101 02/7

Restricted

vsDataAal2Ap

sigLinkId

Connection Control

MORef

Default

Restricted

vsDataAal2Ap

timerErq

Connection Control

Timer

Default

Restricted

vsDataAal2Ap

timerErq

Connection Control

Timer

Default

Restricted

vsDataAal2Ap

timerRel

Connection Control

Timer

Default

Restricted

vsDataAal2Ap

timerRel

Connection Control

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2Ap
vsDataAal2Ap

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2PathDistributionUnit
vsDataAal2PathDistributionUnit

id
id

TN Administration
TN Administration

Id
Id

TND
TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

269 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathDistributionUnit

aal2PathVccTpList

Connection Control

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathDistributionUnit

aal2PathVccTpList

Connection Control

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathDistributionUnit

rpuId

Connection Control

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathDistributionUnit

rpuId

Connection Control

MORef

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2PathDistributionUnit
vsDataAal2PathDistributionUnit

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

270 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2PathId

ATM Connection

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2PathId

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2PathOwner

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2PathOwner

ATM Connection

Real

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2PathVccTp
vsDataAal2PathVccTp

id
id

TN Administration
TN Administration

Id
Id

TND
TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

271 (520)

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2QoSAvailableProfiles

ATM Connection

EnumRef

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

aal2QoSAvailableProfiles

ATM Connection

EnumRef

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Read/Write
Read/Write

Y
Y

Y
Y

Y
Y

N
N

vsDataAal2PathVccTp
vsDataAal2PathVccTp

aal2QoSProfileId
aal2QoSProfileId

ATM Connection
ATM Connection

Id
MORef

Read/Write

vsDataAal2PathVccTp

administrativeState

TN Administration

EnumRef

Read/Write

vsDataAal2PathVccTp

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataAal2PathVccTp

alarmReport

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal2PathVccTp

alarmReport

ATM Connection

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

272 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

vsDataAal2PathVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal2PathVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal2PathVccTp

counterActivation

TN PM Counters

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

273 (520)

TND O&M

Read/Write

vsDataAal2PathVccTp

counterActivation

O&M PM Statistics

Real

TND O&M

Read/Write

vsDataAal2PathVccTp

counterMode

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal2PathVccTp

counterMode

O&M PM Statistics

EnumRef

TND O&M

Read/Write

vsDataAal2PathVccTp

nomPmBlocksize

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal2PathVccTp

nomPmBlocksize

ATM Connection

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read

ATM Connection

EnumRef

Read

ATM Connection

EnumRef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read/Write

ATM Connection

Timer

Default

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataAal2PathVccTp

Date: 2014-05-27
Sheet: 14.0.2

timerCu

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
CPI

1/1553-HSD 101 02/7

Network Parameters

274 (520)

Read/Write

vsDataAal2PathVccTp

timerCu

ATM Connection

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2PathVccTp
vsDataAal2PathVccTp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

vclTpId

ATM Connection

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2PathVccTp

vclTpId

ATM Connection

MORef

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2QosCodePointProfile
vsDataAal2QosCodePointProfile

id
id

TN Administration
TN Administration

Id
Id

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointA

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointA

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointB

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointB

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointC

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointC

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointD

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosCodePointProfile

qualityOfServiceCodePointD

Connection Control

Real

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2QosCodePointProfile
vsDataAal2QosCodePointProfile

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

id
id

TN Administration
TN Administration

Id
Id

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

N
N

Y
Y

N
N

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

profileClassA
profileClassA

Connection Control
Connection Control

StructRef
StructRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

275 (520)

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnNodeDelay

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnProbOfLoss

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassA.boundOnProbOfLoss

Connection Control

Real

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

N
N

Y
Y

N
N

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

profileClassB
profileClassB

Connection Control
Connection Control

StructRef
StructRef

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnNodeDelay

Connection Control

Real

Recommended

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnProbOfLoss

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassB.boundOnProbOfLoss

Connection Control

Real

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

N
N

Y
Y

N
N

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

profileClassC
profileClassC

Connection Control
Connection Control

StructRef
StructRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

276 (520)

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnProbOfLoss

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassC.boundOnProbOfLoss

Connection Control

Real

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

N
N

Y
Y

N
N

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

profileClassD
profileClassD

Connection Control
Connection Control

StructRef
StructRef

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnNodeDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnProbOfDelay

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnProbOfLoss

Connection Control

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataAal2QosProfile

profileClassD.boundOnProbOfLoss

Connection Control

Real

Read

TN Administration

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

TND
TND
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

Read

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2QosProfile
vsDataAal2QosProfile

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

Restricted

277 (520)
TN Administration

MORef

userLabel
userLabel

TN Administration
TN Administration

Label
Label

vsDataAal2RoutingCase
vsDataAal2RoutingCase

id
id

TN Administration
TN Administration

Id
Id

vsDataAal2RoutingCase

numberDirection

Connection Control

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

278 (520)

TND

1/1553-HSD 101 02/7

Restricted

vsDataAal2RoutingCase

numberDirection

Connection Control

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAal2RoutingCase

routeList

Connection Control

MORef

TND

1/1553-HSD 101 02/7

Restricted

vsDataAal2RoutingCase

routeList

Connection Control

MORef

Restricted

vsDataAal2RoutingCase

routePriorityList

Connection Control

Real

TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Network Parameters

279 (520)

Restricted

vsDataAal2RoutingCase

routePriorityList

Connection Control

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2RoutingCase
vsDataAal2RoutingCase

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Sp

a2ea

Connection Control

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal2Sp

a2ea

Connection Control

Real

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal2Sp
vsDataAal2Sp

id
id

TN Administration
TN Administration

Id
Id

Default

Read/Write

vsDataAal2Sp

afi

Connection Control

Real

Default

Read/Write

vsDataAal2Sp

afi

Connection Control

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal2Sp
vsDataAal2Sp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAal5TpVccTp
vsDataAal5TpVccTp

id
id

TN Administration
TN Administration

Id
Id

TND O&M

Read/Write

vsDataAal5TpVccTp

alarmReport

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal5TpVccTp

alarmReport

ATM Connection

EnumRef

TND
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

280 (520)

TND O&M

Read/Write

vsDataAal5TpVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal5TpVccTp

continuityCheck

ATM Connection

Real

TND O&M

Read/Write

vsDataAal5TpVccTp

counterActivation

TN PM Counters

Real

TND O&M

Read/Write

vsDataAal5TpVccTp

counterActivation

O&M PM Statistics

Real

TND O&M

Read/Write

vsDataAal5TpVccTp

counterMode

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal5TpVccTp

counterMode

O&M PM Statistics

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

281 (520)

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal5TpVccTp

fromUserMaxSduSize

ATM Connection

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal5TpVccTp

fromUserMaxSduSize

ATM Connection

Real

TND O&M

Read/Write

vsDataAal5TpVccTp

nomPmBlkSize

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataAal5TpVccTp

nomPmBlkSize

ATM Connection

EnumRef

N/A

Read

TN Administration

EnumRef

Read

TN Administration

EnumRef

Restricted

ATM Connection

Id

N/A
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataAal5TpVccTp

Date: 2014-05-27
Sheet: 14.0.2

processorId

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

1/1553-HSD 101 02/7

Restricted

Read
Read

N
N

Y
Y

Y
Y

N
N

Network Parameters

vsDataAal5TpVccTp

processorId

282 (520)
ATM Connection

MORef

TN Administration
TN Administration

MORef
MORef

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal5TpVccTp

toUserMaxSduSize

ATM Connection

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAal5TpVccTp

toUserMaxSduSize

ATM Connection

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAal5TpVccTp
vsDataAal5TpVccTp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal5TpVccTp

vclTpId

ATM Connection

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAal5TpVccTp

vclTpId

ATM Connection

MORef

Read/Write
Restricted
Read/Write

N
Y
N

Y
Y
Y

Y
N
Y

N
N
N

TND
TND

Read/Write
Restricted
Restricted

N
Y
Y

Y
Y
Y

Y
N
N

N
N
N

vsDataAtmCrossConnection
vsDataAtmCrossConnection

id
id

TN Administration
TN Administration

Id
Id

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

Label
Label

Prepared: EZIEAGA

vsDataAtmCrossConnection
vsDataAtmCrossConnection

Date: 2014-05-27
Sheet: 14.0.2

userLabel
userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

283 (520)

TND

Restricted

vsDataAtmCrossConnection

vclTpAId

ATM Connection

Id

TND

Restricted

vsDataAtmCrossConnection

vclTpAId

ATM Connection

MORef

TND

Restricted

vsDataAtmCrossConnection

vclTpBId

ATM Connection

Id

TND

Restricted

vsDataAtmCrossConnection

vclTpBId

ATM Connection

MORef

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataAtmPort
vsDataAtmPort

id
id

TN Administration
TN Administration

Id
Id

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Default

Restricted

Physical Interface

Real

Prepared: EZIEAGA

vsDataAtmPort

Date: 2014-05-27
Sheet: 14.0.2

hecCorrectionMode

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

284 (520)

Default

Restricted

vsDataAtmPort

hecCorrectionMode

Physical Interface

Real

TND O&M

Read/Write

vsDataAtmPort

loopbackDetection

Physical Interface

EnumRef

TND O&M

Read/Write

vsDataAtmPort

loopbackDetection

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAtmPort
vsDataAtmPort

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAtmPort

uses

Physical Interface

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataAtmPort

uses

Physical Interface

MORef

Read

Physical Interface

StructRef

Read

Physical Interface

StructRef

Read
Read
Read
Read
Read

N
N
N
N
N

Y
Y
Y
Y
Y

N
N
N
N
N

N
N
N
N
N

Physical Interface
Physical Interface
Physical Interface
Physical Interface
Physical Interface

Real
Real
Real
Real
Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

285 (520)

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Read
Restricted
Restricted

N
Y
Y

Y
Y
Y

N
N
N

N
N
N

vsDataAtmTrafficDescriptor
vsDataAtmTrafficDescriptor

id
id

Physical Interface
TN Administration
TN Administration

Real
Id
Id

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmMcr

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmMcr

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmPcr

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmPcr

ATM Connection

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmQos

ATM Connection

EnumRef

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

egressAtmQos

ATM Connection

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmMcr

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmMcr

ATM Connection

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

286 (520)

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmPcr

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmPcr

ATM Connection

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmQos

ATM Connection

EnumRef

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

ingressAtmQos

ATM Connection

EnumRef

TND

Restricted

vsDataAtmTrafficDescriptor

packetDiscard

ATM Connection

Real

TND

Restricted

vsDataAtmTrafficDescriptor

packetDiscard

ATM Connection

Real

Read
Read

N
N

Y
Y

Y
Y

Y
Y

TN Administration
TN Administration

MORef
MORef

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

serviceCategory

ATM Connection

EnumRef

CPI

1/1553-HSD 101 02/7

Restricted

vsDataAtmTrafficDescriptor

serviceCategory

ATM Connection

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataAtmTrafficDescriptor
vsDataAtmTrafficDescriptor

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

EnumRef

Read/Write

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

287 (520)

Read

Status

Read

Status

Restricted
Restricted
Restricted

Y
Y
Y

Y
Y
Y

N
N
N

N
N
N

Id
Id
MORef

Restricted

MORef

Restricted

MORef

Restricted

MORef

Read

EnumRef

Read

EnumRef

Read/Write
Read/Write
Read

N
N
N

Y
Y
N

Y
Y
N

N
N
N

Label
Label
Status

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

288 (520)

Read

Status

Read

EnumRef

Read

EnumRef

Restricted
Restricted
Read

Y
Y
N

Y
Y
Y

N
N
N

N
N
N

Id
Id
Real

Read

Real

Read

EnumRef

Read

EnumRef

Read/Write
Read/Write
Read

N
N
N

Y
Y
Y

Y
Y
N

N
N
N

Label
Label
EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

289 (520)

Read

EnumRef

Read

Status

Read

Status

Restricted
Restricted
Read

Y
Y
N

Y
Y
N

N
N
N

N
N
N

Id
Id
EnumRef

Read

EnumRef

Restricted

Real

Restricted

Real

Read
Read
Read/Write
Read/Write
Restricted

N
N
N
N
Y

Y
Y
Y
Y
Y

N
N
Y
Y
N

Y
Y
N
N
N

MORef
MORef
Label
Label
Id

vsDataDhcp

Date: 2014-05-27
Sheet: 14.0.2

id

TN Administration

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

290 (520)

Restricted

vsDataDhcp

id

TN Administration

Id

Read

vsDataDhcp

dhcpServerAddresses

IP O&M

Real

Read

vsDataDhcp

dhcpServerAddresses

IP O&M

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataDhcp
vsDataDhcp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

N/A

Restricted
Read/Write
Read

Y
N
N

Y
Y
N

N
Y
N

N
Y
N

TN Administration

Status

N/A

Read

TN Administration

Status

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

TN Administration
TN Administration

Id
Id

Prepared: EZIEAGA

vsDataDs0Bundle
vsDataDs0Bundle

Date: 2014-05-27
Sheet: 14.0.2

id
id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

291 (520)

TND

1/1553-HSD 101 02/7

Restricted

vsDataDs0Bundle

listOfTimeSlots

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataDs0Bundle

listOfTimeSlots

Physical Interface

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

292 (520)

TND

1/1553-HSD 101 02/7

Restricted

vsDataDs0Bundle

tdmMode

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataDs0Bundle

tdmMode

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataDs0Bundle
vsDataDs0Bundle

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted
Restricted
Restricted

Y
Y
Y

Y
Y
Y

N
N
Y

N
N
Y

vsDataDscpGroup
vsDataDscpGroup
vsDataDscpGroup

id
id
dscpValues

Id
Id
Real

Restricted

vsDataDscpGroup

dscpValues

Real

Read/Write

vsDataDscpGroup

samplingInterval

Real

Read/Write

vsDataDscpGroup

samplingInterval

Real

Read/Write
Read/Write
Read/Write
Restricted
Read/Write

N
N
Y
Y
N

Y
Y
Y
Y
Y

Y
Y
Y
N
Y

N
N
N
N
N

vsDataDscpGroup
vsDataDscpGroup

userLabel
userLabel

Real
Label

vsDataE1PhysPathTerm

administrativeState

TN Administration

EnumRef

Read/Write

vsDataE1PhysPathTerm

administrativeState

TN Administration

EnumRef

Read/Write

vsDataE1PhysPathTerm

aisReporting

Physical Interface

Real

TND O&M

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND O&M

Read/Write

N/A

Read

N/A

Read

Default

Read/Write

Default

Read/Write

TND O&M

Network Parameters
Physical Interface

Real

TN Administration

Status

TN Administration

Status

vsDataE1PhysPathTerm

crc4Mode

Physical Interface

EnumRef

vsDataE1PhysPathTerm

crc4Mode

Physical Interface

EnumRef

Read/Write

vsDataE1PhysPathTerm

degDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataE1PhysPathTerm

degDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataE1PhysPathTerm

degDegThr

Physical Interface

Real

Prepared: EZIEAGA

vsDataE1PhysPathTerm

Date: 2014-05-27
Sheet: 14.0.2

aisReporting

293 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

294 (520)

TND O&M

Read/Write

vsDataE1PhysPathTerm

degDegThr

Physical Interface

Real

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataE1PhysPathTerm
vsDataE1PhysPathTerm

id
id

TN Administration
TN Administration

Id
Id

Default

Read/Write

vsDataE1PhysPathTerm

idlePattern

Physical Interface

EnumRef

Default

Read/Write

vsDataE1PhysPathTerm

idlePattern

Physical Interface

EnumRef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataE1PhysPathTerm
vsDataE1PhysPathTerm

lineNo
lineNo

Physical Interface
Physical Interface

Real
Real

Default

Read/Write

vsDataE1PhysPathTerm

loopback

Physical Interface

EnumRef

Default

Read/Write

vsDataE1PhysPathTerm

loopback

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

Physical Interface

Real

TND
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

vsDataE1PhysPathTerm

Date: 2014-05-27
Sheet: 14.0.2

rdiReporting

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND O&M

Read/Write

Read
Read

N
N

Y
Y

N
N

Read

Read

Read
Read
TND O&M

TND O&M

Network Parameters
Physical Interface

Real

N
N

TN Administration
TN Administration

MORef
MORef

TN Administration

MORef

TN Administration

MORef

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read/Write

vsDataE1PhysPathTerm

shutDownTimeout

Physical Interface

Timer

Read/Write

vsDataE1PhysPathTerm

shutDownTimeout

Physical Interface

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataE1PhysPathTerm
vsDataE1PhysPathTerm

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND O&M

Read/Write

vsDataE1Ttp

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataE1Ttp

aisReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

vsDataE1PhysPathTerm

Date: 2014-05-27
Sheet: 14.0.2

rdiReporting

295 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Read

Default

Read/Write

vsDataE1Ttp

Default

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

Default

Prepared: EZIEAGA

Network Parameters

296 (520)
TN Administration

Status

crc4Mode

Physical Interface

EnumRef

vsDataE1Ttp

crc4Mode

Physical Interface

EnumRef

vsDataE1Ttp

degDegM

Physical Interface

Real

vsDataE1Ttp

degDegM

Physical Interface

Real

vsDataE1Ttp

degDegThr

Physical Interface

Real

vsDataE1Ttp

degDegThr

Physical Interface

Real

Restricted

vsDataE1Ttp

id

TN Administration

Id

Restricted

vsDataE1Ttp

id

TN Administration

Id

Read/Write

vsDataE1Ttp

idlePattern

Physical Interface

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Read/Write

N/A

Read

N/A

Read

TND O&M

Read/Write

vsDataE1Ttp

TND O&M

Read/Write

vsDataE1Ttp

Read
Read

N
N

Y
Y

N
N

Read
Read

N
N

Y
Y

Read/Write
Read/Write

N
N

Read/Write

Network Parameters
Physical Interface

EnumRef

TN Administration

EnumRef

TN Administration

EnumRef

rdiReporting

Physical Interface

Real

rdiReporting

Physical Interface

Real

Y
Y

TN Administration
TN Administration

MORef
MORef

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Y
Y

Y
Y

N
N

vsDataE1Ttp
vsDataE1Ttp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

vsDataE3PhysPathTerm

administrativeState

TN Administration

EnumRef

Read/Write

vsDataE3PhysPathTerm

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataE3PhysPathTerm

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataE3PhysPathTerm

aisReporting

Physical Interface

Real

Prepared: EZIEAGA

vsDataE1Ttp

Date: 2014-05-27
Sheet: 14.0.2

idlePattern

297 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

298 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

vsDataE3PhysPathTerm

degDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataE3PhysPathTerm

degDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataE3PhysPathTerm

degDegThr

Physical Interface

Real

TND O&M

Read/Write

vsDataE3PhysPathTerm

degDegThr

Physical Interface

Real

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataE3PhysPathTerm
vsDataE3PhysPathTerm

id
id

TN Administration
TN Administration

Id
Id

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataE3PhysPathTerm
vsDataE3PhysPathTerm

lineNo
lineNo

Physical Interface
Physical Interface

Real
Real

Default

Read/Write

vsDataE3PhysPathTerm

loopback

Physical Interface

EnumRef

Default

Read/Write

vsDataE3PhysPathTerm

loopback

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

299 (520)

TND O&M

Read/Write

vsDataE3PhysPathTerm

rdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataE3PhysPathTerm

rdiReporting

Physical Interface

Real

Read

TN Administration

MORef

Read

TN Administration

MORef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

TND O&M

Read/Write

vsDataE3PhysPathTerm

shutDownTimeout

Physical Interface

Timer

TND O&M

Read/Write

vsDataE3PhysPathTerm

shutDownTimeout

Physical Interface

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataE3PhysPathTerm
vsDataE3PhysPathTerm

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted
Restricted
Read

N
Y
N

Y
Y
Y

Y
N
Y

N
N
N

Read

Read
Read

N
N

N
N

N
N

N
N

IP O&M
IP O&M

MORef
MORef

Read

TN Administration

Status

N/A

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

TND
TND

Prepared: EZIEAGA

Network Parameters

300 (520)

Read

TN Administration

Status

Read

IP O&M

MORef

Read

IP O&M

MORef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataEthernetLink
vsDataEthernetLink

id
id

TN Administration
TN Administration

Id
Id

Read

vsDataEthernetLink

interfaceName

IP O&M

Real

Read

vsDataEthernetLink

interfaceName

IP O&M

Real

Read/Write

vsDataEthernetLink

ipv4Addresses

StructRef

Read/Write

vsDataEthernetLink

ipv4Addresses

StructRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

301 (520)

Read/Write

vsDataEthernetLink

ipv4Addresses.broadcastAddress

Real

Read/Write

vsDataEthernetLink

ipv4Addresses.broadcastAddress

Real

Read/Write

vsDataEthernetLink

ipv4Addresses.ipAddress

Real

Read/Write

vsDataEthernetLink

ipv4Addresses.ipAddress

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetLink
vsDataEthernetLink

ipv4Addresses.prefixLength
ipv4Addresses.prefixLength

Real
Real

Read

vsDataEthernetLink

macAddress

IP O&M

Real

Read

vsDataEthernetLink

macAddress

IP O&M

Real

Default

Read/Write

vsDataEthernetLink

metric

IP O&M

Real

Default

Read/Write

vsDataEthernetLink

metric

IP O&M

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

302 (520)

Read/Write

vsDataEthernetLink

mtuSize

IP O&M

Real

Read/Write

vsDataEthernetLink

mtuSize

IP O&M

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

Label
Label

Restricted
Read
Read/Write

Y
N
N

Y
Y
Y

N
Y
Y

N
Y
N

Read

Read

Read/Write

Prepared: EZIEAGA

vsDataEthernetLink
vsDataEthernetLink

Date: 2014-05-27
Sheet: 14.0.2

userLabel
userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

303 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

enableVlan

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

enableVlan

IP Transport

Real

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataEthernetSwitch
vsDataEthernetSwitch

id
id

TN Administration
TN Administration

Id
Id

Read

vsDataEthernetSwitch

macAddress

IP Transport

Real

Read

vsDataEthernetSwitch

macAddress

IP Transport

Real

Read

TN Administration

EnumRef

N/A
N/A

Read

TN Administration

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

pbitQueueMap

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

pbitQueueMap

IP Transport

StructRef

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitch
vsDataEthernetSwitch

pbitQueueMap.pbit
pbitQueueMap.pbit

IP Transport
IP Transport

Real
Real

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitch
vsDataEthernetSwitch

pbitQueueMap.queue
pbitQueueMap.queue

IP Transport
IP Transport

Real
Real

Read

TN Administration

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

304 (520)

Read

TN Administration

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

untaggedIngressPriority

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

untaggedIngressPriority

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

untaggedIngressVid

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

untaggedIngressVid

IP Transport

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitch
vsDataEthernetSwitch

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

vlanMembership

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitch

vlanMembership

IP Transport

StructRef

TND
TND
TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7
5/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Read/Write
Read/Write
Read/Write
Read/Write

N
N
N
N

Y
Y
Y
Y

Y
Y
Y
Y

N
N
N
N

vsDataEthernetSwitch
vsDataEthernetSwitch
vsDataEthernetSwitch
vsDataEthernetSwitch

vlanMembership.egressUntag
vlanMembership.egressUntag
vlanMembership.vid
vlanMembership.vid

IP Transport
IP Transport
IP Transport
IP Transport

Real
Real
Real
Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

305 (520)

Restricted

vsDataEthernetSwitchFabric

id

TN Administration

Id

Read/Write

vsDataEthernetSwitchFabric

userLabel

TN Administration

Label

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

featureStateL2gp

IP

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

featureStateL2gp

IP

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

l2gpPathCost

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

l2gpPathCost

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

l2gpRapidFailover

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchingAdm

l2gpRapidFailover

IP

Real

Read

vsDataEthernetSwitchingAdm

licenseStateL2gp

IP

EnumRef

Read

vsDataEthernetSwitchingAdm

licenseStateL2gp

IP

EnumRef

Read

TN Administration

Status

N/A

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

306 (520)

Read

vsDataEthernetSwitchModule

backPlanePortState

IP Transport

EnumRef

Restricted

vsDataEthernetSwitchModule

id

TN Administration

Id

Default

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchModule

linkAggLinkSelection

IP

EnumRef

Default

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchModule

linkAggLinkSelection

IP

EnumRef

N/A

Read

vsDataEthernetSwitchModule

macAddress

IP Transport

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

MORef

Read/Write

TN Administration

Label

Read

IP Transport

EnumRef

Read/Write

TN Administration

EnumRef

Read

TN Administration

Status

N/A

N/A

Prepared: EZIEAGA

vsDataEthernetSwitchModule

vsDataEthernetSwitchModulePort

Date: 2014-05-27
Sheet: 14.0.2

userLabel

administrativeState

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

307 (520)

Read/Write

vsDataEthernetSwitchModulePort

egressUntagVlanRef

IP Transport

MORef

Restricted

vsDataEthernetSwitchModulePort

id

TN Administration

Id

vsDataEthernetSwitchModulePort

externalPort

IP Transport

Real

IP

MORef

IP

MoRef

TND

5/1553-HSD 101 02/7

Read/Write

TND

5/1553-HSD 101 02

Read/Write

TND

5/1553-HSD 101 02

Read/Write

Prepared: EZIEAGA

Network Parameters

vsDataEthernetSwitchModulePort

Date: 2014-05-27
Sheet: 14.0.2

lagRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

308 (520)

Read/Write

vsDataEthernetSwitchModulePort

operatingMode

IP Transport

StructRef

Default

Read/Write

vsDataEthernetSwitchModulePort

operatingMode.autoNegotiation

IP Transport

Real

Default

Read/Write

vsDataEthernetSwitchModulePort

operatingMode.configuredSpeedDuplex

IP Transport

EnumRef

N/A

Read

TN Administration

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchModulePort

pbitQueueMap

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchModulePort

pbitQueueMap.pbit

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchModulePort

pbitQueueMap.queue

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataEthernetSwitchModulePort

portNo

IP Transport

Real

Read/Write

Read/Write

Read/Write

TND

Prepared: EZIEAGA

5/1553-HSD 101 02

EnumRef

vsDataEthernetSwitchModulePort

remoteFaultIndication

EnumRef

IP

Date: 2014-05-27
Sheet: 14.0.2

EnumRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

309 (520)

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchModulePort

trafficState

IP

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchModulePort

untaggedIngressPriority

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchModulePort

untaggedIngressVlanRef

IP Transport

MORef

Read/Write

vsDataEthernetSwitchModulePort

userLabel

TN Administration

Label

Read/Write

vsDataEthernetSwitchModulePort

vlanRef

IP Transport

MORef

Read

vsDataEthernetSwitchPort

actualSpeedDuplex

IP Transport

EnumRef

Read

vsDataEthernetSwitchPort

actualSpeedDuplex

IP Transport

EnumRef

Read/Write

vsDataEthernetSwitchPort

administrativeState

TN Administration

EnumRef

Read/Write

vsDataEthernetSwitchPort

administrativeState

TN Administration

EnumRef

TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

310 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort

id
id

IP Transport
TN Administration

Id
Id

Default

Read/Write

vsDataEthernetSwitchPort

ingressPeakBitrate

IP Transport

Real

Default

Read/Write

vsDataEthernetSwitchPort

ingressPeakBitrate

IP Transport

Real

Read/Write

vsDataEthernetSwitchPort

operatingMode

IP Transport

StructRef

Read/Write

vsDataEthernetSwitchPort

operatingMode

IP Transport

StructRef

Read/Write

vsDataEthernetSwitchPort

operatingMode.autoNegotiation

IP Transport

Real

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

311 (520)

Default

Read/Write

vsDataEthernetSwitchPort

operatingMode.autoNegotiation

IP Transport

Real

Default

Read/Write

vsDataEthernetSwitchPort

operatingMode.configuredSpeedDuplex

IP Transport

EnumRef

Default

Read/Write

vsDataEthernetSwitchPort

operatingMode.configuredSpeedDuplex

IP Transport

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

pbitQueueMap

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

pbitQueueMap

IP Transport

StructRef

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort

pbitQueueMap.pbit
pbitQueueMap.pbit

IP Transport
IP Transport

Real
Real

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort

pbitQueueMap.queue
pbitQueueMap.queue

IP Transport
IP Transport

Real
Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataEthernetSwitchPort

portNo

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataEthernetSwitchPort

portNo

IP Transport

Real

Read

vsDataEthernetSwitchPort

sfpInformation

IP Transport

StructRef

Read

vsDataEthernetSwitchPort

sfpInformation

IP Transport

StructRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

312 (520)

Read
Read

N
N

Y
Y

N
N

N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

IP Transport
IP Transport

Real
Real

Read

vsDataEthernetSwitchPort

sfpInformation.sfpState

IP Transport

EnumRef

Read

vsDataEthernetSwitchPort

sfpInformation.sfpState

IP Transport

EnumRef

Read

vsDataEthernetSwitchPort

sfpInformation.sfpType

IP Transport

Real

Read

vsDataEthernetSwitchPort

sfpInformation.sfpType

IP Transport

Real

Read

vsDataEthernetSwitchPort

sfpPort

IP Transport

Real

Read

vsDataEthernetSwitchPort

sfpPort

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

systemPort

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

systemPort

IP Transport

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchPort

trafficState

IP

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataEthernetSwitchPort

trafficState

IP

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

untaggedIngressPriority

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

313 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

untaggedIngressPriority

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

untaggedIngressVid

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

untaggedIngressVid

IP Transport

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

vlanMembership

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataEthernetSwitchPort

vlanMembership

IP Transport

StructRef

TND
TND
TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7
5/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Read/Write
Read/Write
Read/Write
Read/Write
Read/Write

N
N
N
N
N

Y
Y
Y
Y
Y

Y
Y
Y
Y
Y

N
N
N
N
N

vsDataEthernetSwitchPort
vsDataEthernetSwitchPort
vsDataEthernetSwitchPort
vsDataEthernetSwitchPort
vsDataFastEthernet

vlanMembership.egressUntag
vlanMembership.egressUntag
vlanMembership.vid
vlanMembership.vid
administrativeState

IP Transport
IP Transport
IP Transport
IP Transport
TN Administration

Real
Real
Real
Real
EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

TND

Read/Write

vsDataFastEthernet

TND

Restricted

vsDataFastEthernet

Read

Default

Read/Write

vsDataFastEthernet

TND

Restricted

vsDataFastEthernet

N/A

Read

Read

Read

Read/Write

Read

Read

Prepared: EZIEAGA

314 (520)
TN Administration

Status

defaultRouter

IP Transport

Real

id

TN Administration

Id

TN Administration

Real

mtu

IP Transport

Real

networkPrefixLength

IP Transport

Real

TN Administration

EnumRef

TN Administration

MORef

TN Administration

Real

TN Administration

Label

IP Transport

EnumRef

IP Transport

EnumRef

vsDataFastEthernet

Date: 2014-05-27
Sheet: 14.0.2

userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

315 (520)

N/A

Read

IP Transport

EnumRef

N/A

Read

IP Transport

EnumRef

Read/Write

vsDataGigaBitEthernet

administrativeState

TN Administration

EnumRef

Read/Write

vsDataGigaBitEthernet

administrativeState

TN Administration

EnumRef

Read/Write

vsDataGigaBitEthernet

autoNegotiation

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

autoNegotiation

IP Transport

Real

Read

TN Administration

Status

Default

N/A

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

316 (520)

Read

Read/Write

vsDataGigaBitEthernet

configPbitArp

Real

Read/Write

vsDataGigaBitEthernet

configPbitArp

Real

TND

Read/Write

vsDataGigaBitEthernet

configuredSpeedDuplex

EnumRef

TND

Read/Write

vsDataGigaBitEthernet

configuredSpeedDuplex

EnumRef

Prepared: EZIEAGA

TN Administration

Date: 2014-05-27
Sheet: 14.0.2

Status

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

317 (520)

Default

Read/Write

vsDataGigaBitEthernet

defRoutersLinkSwitch

Real

Default

Read/Write

vsDataGigaBitEthernet

defRoutersLinkSwitch

Real

Restricted

vsDataGigaBitEthernet

dscpPbitMap

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IP Transport

StructRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

318 (520)

Restricted

vsDataGigaBitEthernet

dscpPbitMap

IP Transport

StructRef

Restricted

vsDataGigaBitEthernet

dscpPbitMap.dscp

IP Transport

Real

Restricted

vsDataGigaBitEthernet

dscpPbitMap.dscp

IP Transport

Real

Restricted

vsDataGigaBitEthernet

dscpPbitMap.pbit

IP Transport

Real

Restricted

vsDataGigaBitEthernet

dscpPbitMap.pbit

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

frameFormat

IP Transport

EnumRef

Default

Read/Write

vsDataGigaBitEthernet

frameFormat

IP Transport

EnumRef

TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataGigaBitEthernet
vsDataGigaBitEthernet

id
id

TN Administration
TN Administration

Id
Id

Read

IP Transport

EnumRef

Read

IP Transport

EnumRef

TND

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

5/1553-HSD 101 02/7

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

319 (520)

Read

IP Transport

EnumRef

Read

IP Transport

EnumRef

Restricted

vsDataGigaBitEthernet

linkType

IP Transport

EnumRef

Restricted

vsDataGigaBitEthernet

linkType

IP Transport

EnumRef

Read

vsDataGigaBitEthernet

macAddressLink1

IP Transport

Real

Read

vsDataGigaBitEthernet

macAddressLink1

IP Transport

Real

Read

vsDataGigaBitEthernet

macAddressLink2

IP Transport

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

320 (520)

Read

vsDataGigaBitEthernet

macAddressLink2

Default

Read/Write

vsDataGigaBitEthernet

masterMode

Real

Default

Read/Write

vsDataGigaBitEthernet

masterMode

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Default

Restricted

vsDataGigaBitEthernet

portNo

IP Transport

Real

Default

Restricted

vsDataGigaBitEthernet

portNo

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

primaryLink

IP Transport

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

IP Transport

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Network Parameters

321 (520)

Read/Write

vsDataGigaBitEthernet

primaryLink

IP Transport

EnumRef

Read/Write

vsDataGigaBitEthernet

protectiveMode

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

protectiveMode

IP Transport

Real

N/A

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

Y
Y
N

vsDataGigaBitEthernet

sfpInformation

IP Transport
IP Transport

MORef
MORef
StructRef

N/A

Read

vsDataGigaBitEthernet

sfpInformation

IP Transport

StructRef

N/A
N/A

Read
Read

N
N

Y
Y

N
N

N
N

vsDataGigaBitEthernet
vsDataGigaBitEthernet

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

IP Transport
IP Transport

Real
Real

N/A

Read

vsDataGigaBitEthernet

sfpInformation.sfpState

IP Transport

EnumRef

N/A

Read

vsDataGigaBitEthernet

sfpInformation.sfpState

IP Transport

EnumRef

N/A

Read

vsDataGigaBitEthernet

sfpInformation.sfpType

IP Transport

Real

N/A

Read

vsDataGigaBitEthernet

sfpInformation.sfpType

IP Transport

Real

N/A

Read

vsDataGigaBitEthernet

sfpPort

IP Transport

Real

Default

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

TND O&M

Default

Default

Prepared: EZIEAGA

Network Parameters

322 (520)

Read

vsDataGigaBitEthernet

sfpPort

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

shutDownTimeout

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

shutDownTimeout

IP Transport

Timer

Read/Write

vsDataGigaBitEthernet

statePropagationDelay

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

statePropagationDelay

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

switchBackTimer

IP Transport

Real

Read/Write

vsDataGigaBitEthernet

switchBackTimer

IP Transport

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataGigaBitEthernet
vsDataGigaBitEthernet

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

323 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

Restricted

TN Administration

Id

Restricted

TN Administration

Id

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write

TN Administration

Label

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

324 (520)

Read/Write

TN Administration

Label

Restricted
Read/Write
Read
Read

N
N
N
N

Y
Y
Y
Y

N
Y
N
N

N
N
N
N

Physical Interface
Physical Interface

Real
Real

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

TN Administration
TN Administration

Id
Id

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write

Physical Interface

MORef

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataImaGroup
vsDataImaGroup

vsDataImaGroup

Date: 2014-05-27
Sheet: 14.0.2

id
id

physicalPortList

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

325 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataImaGroup

physicalPortList

Physical Interface

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataImaGroup

requiredNumberOfLinks

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataImaGroup

requiredNumberOfLinks

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

Label
Label

Prepared: EZIEAGA

vsDataImaGroup
vsDataImaGroup

Date: 2014-05-27
Sheet: 14.0.2

userLabel
userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

326 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND

Restricted

vsDataImaLink

id

TN Administration

Id

N/A

Restricted

vsDataImaLink

id

TN Administration

Id

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataImaLink
vsDataImaLink

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

1/1553-HSD 101 02/7

Restricted

vsDataImaLink

uses

Physical Interface

MORef

TND

1/1553-HSD 101 02/7

Restricted

vsDataImaLink

uses

Physical Interface

MORef

Read

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

327 (520)

Read/Write
Restricted

N
N

Y
Y

Y
N

N
N

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataInternalEthernetPort

configPbitArp

Real

Read/Write

vsDataInternalEthernetPort

configPbitArp

Real

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap

IP Transport

StructRef

TND

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap.dscp

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap.dscp

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap.pbit

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataInternalEthernetPort

dscpPbitMap.pbit

IP Transport

Real

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataInternalEthernetPort
vsDataInternalEthernetPort

ethernetSwitchRef
ethernetSwitchRef

IP Transport
IP Transport

MORef
MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

328 (520)

Default

Read/Write

vsDataInternalEthernetPort

frameFormat

IP Transport

EnumRef

Default

Read/Write

vsDataInternalEthernetPort

frameFormat

IP Transport

EnumRef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataInternalEthernetPort
vsDataInternalEthernetPort

id
id

TN Administration
TN Administration

Id
Id

Read

vsDataInternalEthernetPort

macAddress

IP Transport

Real

Read

vsDataInternalEthernetPort

macAddress

IP Transport

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataInternalEthernetPort
vsDataInternalEthernetPort

userLabel
userLabel

TN Administration
TN Administration

Label
Label

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

329 (520)

TND

2/1553-HSD 101 02/6

Read/Write

vsDataIp

defDomainName

IP O&M

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataIp

defDomainName

IP O&M

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataIp

dnsServerAddresses

IP O&M

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

2/1553-HSD 101 02/6

Network Parameters

330 (520)

Read/Write

vsDataIp

dnsServerAddresses

IP O&M

Real

Read/Write

vsDataIp

dscp

IP O&M

Real

Read/Write

vsDataIp

dscp

IP O&M

Real

Default
Default

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIp
vsDataIp

icmpRedirect
icmpRedirect

IP O&M
IP O&M

Real
Real

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataIp
vsDataIp

id
id

TN Administration
TN Administration

Id
Id

TND

TND

5/1553-HSD 101 02/7

TND

2/1553-HSD 101 02/6

Read/Write

vsDataIp

isDefDomainName

IP O&M

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataIp

isDefDomainName

IP O&M

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

331 (520)

TND

Read/Write

vsDataIp

isRecursiveSearch

IP O&M

Real

TND

Read/Write

vsDataIp

isRecursiveSearch

IP O&M

Real

TND

Read/Write

vsDataIp

isSubDomainName

IP O&M

Real

TND

Read/Write

vsDataIp

isSubDomainName

IP O&M

Real

TND

2/1553-HSD 101 02/7

Read/Write

vsDataIp

nodeInterfaceName

IP O&M

Real

TND

2/1553-HSD 101 02/7

Read/Write

vsDataIp

nodeInterfaceName

IP O&M

Real

N/A
N/A

Read
Read

N
N

Y
Y

Y
Y

N
N

vsDataIp
vsDataIp

nodeIpAddress
nodeIpAddress

IP O&M
IP O&M

Real
Real

Default
Default

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIp
vsDataIp

noOfRetrans
noOfRetrans

IP O&M
IP O&M

Real
Real

Read

IP O&M

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

332 (520)

Read

IP O&M

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Default

Read/Write

vsDataIp

retransInterval

IP O&M

Real

Default

Read/Write

vsDataIp

retransInterval

IP O&M

Real

Default

Read/Write

vsDataIp

udpChecksumState

IP O&M

State

Default

Read/Write

vsDataIp

udpChecksumState

IP O&M

State

Read/Write

vsDataIp

useHostFile

IP O&M

Real

Default

Prepared: EZIEAGA

2/1553-HSD 101 02/6

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

2/1553-HSD 101 02/6

Network Parameters

333 (520)

Read/Write

vsDataIp

useHostFile

IP O&M

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIp
vsDataIp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

CPI

2/1553-HSD 101 02/7

Read/Write

vsDataIp

workingMode

IP O&M

EnumRef

Recommended

2/1553-HSD 101 02/7

Read/Write

vsDataIp

workingMode

IP O&M

EnumRef

TND

Restricted

vsDataIpAccessAutoConfig

id

TN Administration

Id

TND

Restricted

vsDataIpAccessAutoConfig

maxIpAddress

IP Transport

Real

TND

Restricted

vsDataIpAccessAutoConfig

minIpAddress

IP Transport

Real

Read

vsDataIpAccessAutoConfig

nrOfUnusedAdresses

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

334 (520)

Read

TN Administration

MORef

Read

vsDataIpAccessAutoConfig

totalNrOfAddresses

IP Transport

Real

Read/Write

vsDataIpAccessAutoConfig

userLabel

TN Administration

Label

Read/Write

vsDataIpAccessHostEt

administrativeState

TN Administration

EnumRef

Read/Write

vsDataIpAccessHostEt

administrativeState

TN Administration

EnumRef

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

TN Administration
TN Administration

Id
Id

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Prepared: EZIEAGA

vsDataIpAccessHostEt
vsDataIpAccessHostEt

Date: 2014-05-27
Sheet: 14.0.2

id
id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

335 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostEt

ipAddress

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostEt

ipAddress

IP Transport

Real

Default

Read/Write

vsDataIpAccessHostEt

ipDefaultTtl

IP Transport

Real

Default

Read/Write

vsDataIpAccessHostEt

ipDefaultTtl

IP Transport

Real

Restricted

vsDataIpAccessHostEt

ipInterfaceMoRef

IP Transport

MORef

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

336 (520)

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostEt

ipInterfaceMoRef

IP Transport

MORef

TND
TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Read/Write
Read/Write
Read/Write

N
N
N

Y
Y
Y

Y
Y
Y

N
N
N

vsDataIpAccessHostEt
vsDataIpAccessHostEt
vsDataIpAccessHostEt

ntpDscp
ntpDscp
ntpServerMode

Network Sync
Network Sync
Network Sync

Real
Real
EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostEt

ntpServerMode

Network Sync

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read
Read/Write
Read/Write
Read

N
N
N
N
N

Y
Y
Y
Y
N

N
N
Y
Y
N

Y
Y
N
N
N

TN Administration
TN Administration
TN Administration
TN Administration
IP Transport

MORef
MORef
Label
Label
Id

Read

IP Transport

MORef

Read/Write

vsDataIpAccessHostGpb

administrativeState

TN Administration

EnumRef

Read/Write

vsDataIpAccessHostGpb

administrativeState

TN Administration

EnumRef

TND

Restricted

vsDataIpAccessHostGpb

autoConfig

IP Transport

EnumRef

TND

Restricted

vsDataIpAccessHostGpb

autoConfig

IP Transport

EnumRef

TND

Restricted

vsDataIpAccessHostGpb

autoConfigIdentity

IP Transport

MORef

TND

Restricted

vsDataIpAccessHostGpb

autoConfigIdentity

IP Transport

MORef

TND

Restricted

vsDataIpAccessHostGpb

autoConfigIdentity2

IP Transport

MORef

Prepared: EZIEAGA

vsDataIpAccessHostEt
vsDataIpAccessHostEt

Date: 2014-05-27
Sheet: 14.0.2

userLabel
userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Restricted

N/A

Read

N/A

Read

Restricted

Restricted

Restricted

TND

5/1553-HSD 101 02/7

TND

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

vsDataIpAccessHostGpb

IP Transport

MORef

TN Administration

Status

TN Administration

Status

vsDataIpAccessHostGpb

generalProcessorUnitId

IP Transport

Id

vsDataIpAccessHostGpb

generalProcessorUnitId

IP Transport

MORef

vsDataIpAccessHostGpb

interface1

IP Transport

MORef

Date: 2014-05-27
Sheet: 14.0.2

autoConfigIdentity2

337 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

338 (520)

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostGpb

interface1

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostGpb

interface2

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostGpb

interface2

IP Transport

MORef

TND
TND

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataIpAccessHostGpb
vsDataIpAccessHostGpb

id
id

TN Administration
TN Administration

Id
Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

339 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostGpb

ipAddress1

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostGpb

ipAddress1

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostGpb

ipAddress2

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

340 (520)

Read/Write

vsDataIpAccessHostGpb

ipAddress2

IP Transport

Real

Default

Read/Write

vsDataIpAccessHostGpb

ipDefaultTtl

IP Transport

Real

Default

Read/Write

vsDataIpAccessHostGpb

ipDefaultTtl

IP Transport

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write

vsDataIpAccessHostGpb

reassemblyTimeout

Real

Read/Write

vsDataIpAccessHostGpb

reassemblyTimeout

Real

Read
Read
Read/Write
Read/Write

N
N
N
N

Y
Y
Y
Y

N
N
Y
Y

Y
Y
N
N

vsDataIpAccessHostGpb
vsDataIpAccessHostGpb

userLabel
userLabel

TN Administration
TN Administration

MORef
MORef
Label
Label

Read/Write

vsDataIpAccessHostPool

administrativeState

TN Administration

EnumRef

Read

TN Administration

Status

Restricted
Read/Write

Y
N

Y
Y

N
Y

N
Y

TN Administration
IP Transport

Id
MORef

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

TN Administration

vsDataIpAccessHostPool
vsDataIpAccessHostPool

Date: 2014-05-27
Sheet: 14.0.2

id
ipAccessHostRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

341 (520)

Read

TN Administration

EnumRef

Read

TN Administration

MORef

Read/Write

TN Administration

Label

Read

IP Transport

MORef

Read/Write

vsDataIpAccessHostSpb

administrativeState

TN Administration

EnumRef

TND

Restricted

vsDataIpAccessHostSpb

autoConfig

IP Transport

EnumRef

TND

Restricted

vsDataIpAccessHostSpb

autoConfigIdentity

IP Transport

MORef

TND

Restricted

vsDataIpAccessHostSpb

autoConfigIdentity2

IP Transport

MORef

N/A

Read

TN Administration

Status

vsDataIpAccessHostPool

userLabel

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostSpb

interface2

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpAccessHostSpb

id

TN Administration

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

342 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostSpb

ipAddress

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessHostSpb

ipAddress2

IP Transport

Real

Read/Write

vsDataIpAccessHostSpb

ipDefaultTtl

IP Transport

Real

Restricted

vsDataIpAccessHostSpb

ipInterface

IP Transport

MORef

Read

TN Administration

EnumRef

Read/Write

Read/Write

Read

Restricted

vsDataIpAccessHostSpb

Read/Write

vsDataIpAccessHostSpb

Default

TND

5/1553-HSD 101 02/7

N/A

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Real

vsDataIpAccessHostSpb

Date: 2014-05-27
Sheet: 14.0.2

reassemblyTimeout

Real

TN Administration

MORef

spmId

IP Transport

MORef

userLabel

TN Administration

Label

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

343 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessSctp

ipAccessHostEtRef1

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessSctp

ipAccessHostEtRef1

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessSctp

ipAccessHostEtRef2

IP Transport

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpAccessSctp

ipAccessHostEtRef2

IP Transport

MORef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataIpAccessSctp
vsDataIpAccessSctp

id
id

TN Administration
TN Administration

Id
Id

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

N/A
N/A

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

344 (520)

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpAccessSctp
vsDataIpAccessSctp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

Restricted

vsDataIpAtmLink

aal5TpVccTpId

IP O&M

Id

TND

Restricted

vsDataIpAtmLink

aal5TpVccTpId

IP O&M

MORef

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

Read

Read
Read

N
N

Y
Y

N
N

N
N

vsDataIpAtmLink
vsDataIpAtmLink

345 (520)
TN Administration

Status

interfaceName
interfaceName

IP O&M
IP O&M

Real
Real

TND

2/1553-HSD 101 02/6

Restricted

vsDataIpAtmLink

ipAddress

IP O&M

Real

TND

2/1553-HSD 101 02/6

Restricted

vsDataIpAtmLink

ipAddress

IP O&M

Real

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataIpAtmLink
vsDataIpAtmLink

id
id

TN Administration
TN Administration

Id
Id

Read/Write

vsDataIpAtmLink

metric

IP O&M

Real

TND
TND
TND

Prepared: EZIEAGA

2/1553-HSD 101 02/6

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

2/1553-HSD 101 02/6

Network Parameters

346 (520)

Read/Write

vsDataIpAtmLink

metric

IP O&M

Real

Default

Read/Write

vsDataIpAtmLink

monitor

IP O&M

Real

Default

Read/Write

vsDataIpAtmLink

monitor

IP O&M

Real

Default

2/1553-HSD 101 02/6

Read/Write

vsDataIpAtmLink

monitorInterval

IP O&M

Real

Recommended

2/1553-HSD 101 02/6

Read/Write

vsDataIpAtmLink

monitorInterval

IP O&M

Real

Default
Default

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpAtmLink
vsDataIpAtmLink

monitorRetries
monitorRetries

IP O&M
IP O&M

Real
Real

Default

Read/Write

vsDataIpAtmLink

mtuSize

IP O&M

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Read/Write

N/A

Read

N/A

Read

Read

Read

Restricted

TND

Prepared: EZIEAGA

2/1553-HSD 101 02/6

Network Parameters

vsDataIpAtmLink

IP O&M

Real

TN Administration

EnumRef

TN Administration

EnumRef

TN Administration

MORef

TN Administration

MORef

IP O&M

Real

vsDataIpAtmLink

Date: 2014-05-27
Sheet: 14.0.2

mtuSize

347 (520)

subnetMask

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

2/1553-HSD 101 02/6

TND

Network Parameters

348 (520)

Restricted

vsDataIpAtmLink

subnetMask

IP O&M

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpAtmLink
vsDataIpAtmLink

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataIpEthPacketDataRouter

administrativeState

TN Administration

EnumRef

Read

TN Administration

Status

TND
TND

5/1553-HSD 101 02/7

Restricted
Restricted

N
N

Y
Y

Y
Y

N
N

vsDataIpEthPacketDataRouter
vsDataIpEthPacketDataRouter

ipAccessHostSpbRef
ipAddressSelection

IP Transport
IP Transport

MORef
EnumRef

TND

5/1553-HSD 101 02/7

Restricted
Read

Y
N

Y
N

N
Y

N
N

vsDataIpEthPacketDataRouter

id

TN Administration
TN Administration

Id
EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read

TND

Read/Write

N/A

Read

Network Parameters

vsDataIpEthPacketDataRouter

userLabel

349 (520)
TN Administration

MORef

TN Administration

Label

TN Administration

Status

N/A

2/1553-HSD 101 02/7

Read

vsDataIpHostLink

interfaceName

IP Transport

Real

TND
TND

2/1553-HSD 101 02/7


2/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataIpHostLink
vsDataIpHostLink

id
ipInterfaceMoRef

TN Administration
IP Transport

Id
MORef

Read/Write

vsDataIpHostLink

ipv4Addresses

Read

N/A

Prepared: EZIEAGA

Real

TN Administration

Date: 2014-05-27
Sheet: 14.0.2

EnumRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND
N/A

2/1553-HSD 101 02/7

N/A

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Read/Write
Read

N
N

Y
N

Y
N

N
N

Read

Read/Write

Network Parameters

vsDataIpHostLink

vsDataIpInterface

Date: 2014-05-27
Sheet: 14.0.2

userLabel

defaultRouter0

350 (520)
TN Administration
TN Administration

Label
Status

TN Administration

Status

IP Transport

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

Read/Write

Read

Read

Network Parameters

vsDataIpInterface

defaultRouter0

351 (520)
IP Transport

Real

IP Transport

EnumRef

IP Transport

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

defaultRouter1

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

defaultRouter1

IP Transport

Real

Read

IP Transport

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read

Network Parameters

352 (520)
IP Transport

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

defaultRouter2

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

defaultRouter2

IP Transport

Real

Read

IP Transport

EnumRef

Read

IP Transport

EnumRef

Read/Write

IP Transport

Real

TND

Prepared: EZIEAGA

vsDataIpInterface

Date: 2014-05-27
Sheet: 14.0.2

defaultRouterPingInterval

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Read/Write

Read

Read

Restricted
Restricted

Y
Y

Default

Read/Write

Default

Network Parameters
IP Transport

Real

IP Transport

EnumRef

IP Transport

EnumRef

Y
Y

N
N

N
N

vsDataIpInterface
vsDataIpInterface

id
id

TN Administration
TN Administration

Id
Id

vsDataIpInterface

maxNoOfFailedPings

IP Transport

Real

Read/Write

vsDataIpInterface

maxNoOfFailedPings

IP Transport

Real

Default

Read/Write

vsDataIpInterface

maxWaitForPingReply

IP Transport

Real

Default

Read/Write

vsDataIpInterface

maxWaitForPingReply

IP Transport

Real

TND
TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

vsDataIpInterface

Date: 2014-05-27
Sheet: 14.0.2

defaultRouterPingInterval

353 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

354 (520)

Default

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

mtu

IP Transport

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

mtu

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

355 (520)

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpInterface

networkPrefixLength

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpInterface

networkPrefixLength

IP Transport

Real

Default

Read/Write

vsDataIpInterface

noOfPingsBeforeOk

IP Transport

Real

Default

Read/Write

vsDataIpInterface

noOfPingsBeforeOk

IP Transport

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Restricted

IP Transport

Real

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

vsDataIpInterface

Date: 2014-05-27
Sheet: 14.0.2

ownIpAddressActive

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

356 (520)

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpInterface

ownIpAddressActive

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpInterface

ownIpAddressPassive

IP Transport

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataIpInterface

ownIpAddressPassive

IP Transport

Real

Read

TN Administration

MORef

Read

TN Administration

MORef

Read/Write

IP Transport

Real

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

vsDataIpInterface

Date: 2014-05-27
Sheet: 14.0.2

rps

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

357 (520)

Read/Write

vsDataIpInterface

rps

IP Transport

Real

Read

vsDataIpInterface

subnet

IP Transport

Real

Read

vsDataIpInterface

subnet

IP Transport

Real

Default

Read/Write

vsDataIpInterface

switchBackTimer

IP Transport

Timer

Default

Read/Write

vsDataIpInterface

switchBackTimer

IP Transport

Timer

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

TND

Network Parameters

358 (520)

Read/Write

vsDataIpInterface

trafficType

IP Transport

EnumRef

Read/Write

vsDataIpInterface

trafficType

IP Transport

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpInterface
vsDataIpInterface

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

vid

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

vid

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

359 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

vLan

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIpInterface

vLan

IP Transport

Real

Read/Write

vsDataIpInterface

vlanRef

IP Transport

MORef

Read

Restricted
Restricted
Read
Restricted
Read/Write
Restricted

Y
Y
N
Y
N
Y

Y
Y
Y
Y
Y
Y

N
Y
N
Y
Y
N

N
N
Y
N
N
N

vsDataIpInterfaceGroup
vsDataIpInterfaceGroup

id
primaryIpInterfaceRef

vsDataIpInterfaceGroup
vsDataIpInterfaceGroup
vsDataIpOam

secondaryIpInterfaceRef
userLabel
id

TN Administration

Id
MORef
MORef
MORef
Label
Id

Restricted

vsDataIpOam

id

TN Administration

Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpOam
vsDataIpOam

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataIppm

featureStateTwampResponder

TND

Prepared: EZIEAGA

MORef

Date: 2014-05-27
Sheet: 14.0.2

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

360 (520)

Read/Write

vsDataIppm

featureStateTwampResponder

EnumRef

Restricted
Read

Y
N

Y
N

N
Y

N
N

vsDataIppm
vsDataIppm

id
licenseStateTwampResponder

Id
Real

Read

vsDataIppm

licenseStateTwampResponder

EnumRef

Read/Write
Read

N
N

Y
Y

Y
N

N
Y

vsDataIppm

userLabel

Read

Restricted

vsDataIpRoutingTable

Restricted

Read/Write

Read/Write

Read/Write

Read/Write

IP O&M

Label
Real

IP O&M

Real

id

TN Administration

Id

vsDataIpRoutingTable

id

TN Administration

Id

vsDataIpRoutingTable

staticRoutes

IP O&M

StructRef

vsDataIpRoutingTable

staticRoutes

IP O&M

StructRef

vsDataIpRoutingTable

staticRoutes.indexOfStaticRoute

IP O&M

Real

vsDataIpRoutingTable

staticRoutes.indexOfStaticRoute

IP O&M

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpRoutingTable
vsDataIpRoutingTable

staticRoutes.ipAddress
staticRoutes.ipAddress

IP O&M
IP O&M

Real
Real

Read/Write

vsDataIpRoutingTable

staticRoutes.networkMask

IP O&M

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

N/A

5/1553-HSD 101 02/7

Prepared: EZIEAGA

Network Parameters

361 (520)

Read/Write

vsDataIpRoutingTable

staticRoutes.networkMask

IP O&M

Real

Read/Write

vsDataIpRoutingTable

staticRoutes.nextHopIpAddr

IP O&M

Real

Read/Write

vsDataIpRoutingTable

staticRoutes.nextHopIpAddr

IP O&M

Real

Read/Write

vsDataIpRoutingTable

staticRoutes.redistribute

IP O&M

Real

Read/Write

vsDataIpRoutingTable

staticRoutes.redistribute

IP O&M

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpRoutingTable
vsDataIpRoutingTable

staticRoutes.routeMetric
staticRoutes.routeMetric

IP O&M
IP O&M

Real
Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataIpRoutingTable
vsDataIpRoutingTable

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataIpSyncRef

administrativeState

TN Administration

EnumRef

Read

TN Administration

Status

Read

vsDataIpSyncRef

cachedIpAddress

Network Sync

Real

Restricted

vsDataIpSyncRef

id

TN Administration

Id

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

N/A

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

TND
N/A
N/A

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

Read/Write

vsDataIpSyncRef

Read

Read
Read/Write
Restricted

N
N
Y

Y
Y
Y

N
Y
N

Y
N
N

vsDataIpSyncRef
vsDataIpSystem

Restricted

Read/Write
Read/Write

N
N

Y
Y

Y
Y

Read
Read/Write
Read/Write

N
N
Y

Y
Y
Y

Read/Write

Read/Write

Network Sync

Real

TN Administration

EnumRef

userLabel
id

TN Administration
TN Administration
TN Administration

MORef
Label
Id

vsDataIpSystem

id

TN Administration

Id

N
N

vsDataIpSystem
vsDataIpSystem

userLabel
userLabel

TN Administration
TN Administration

Label
Label

N
Y
Y

Y
N
N

vsDataIpv6Interface
vsDataIub

trafficSchedulerRef
controlPlaneTransportOption

IP Transport

MORef
MORef
StructRef

vsDataIub

controlPlaneTransportOption.atm

ATM Connection

Real

vsDataIub

controlPlaneTransportOption.ipV4

IP Transport

Real

Restricted
Read/Write

Y
Y

Y
Y

N
Y

N
N

vsDataIub
vsDataIub

id
rbsId

RN Administration
O&M

Id
Id

Read/Write

vsDataIub

userPlaneIpResourceRef

IP Transport

MORef

Date: 2014-05-27
Sheet: 14.0.2

ntpServerIpAddress

362 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

363 (520)

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write

vsDataIub

userPlaneTransportOption

IP Transport

StructRef

TND

vsDataIub

userPlaneTransportOption.atm

ATM Connection

Real

vsDataIub

userPlaneTransportOption.ipV4

IP Transport

Real

TND

1/1553-HSD 101 02/7


Read/Write
5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
Read/Write
5/1553-HSD 101 02/7
126/1553-HSD 101 02/7 Read/Write

vsDataIuBcLink

cbcIpAddress

Cell Broadcast

Real

Default

126/1553-HSD 101 02/7 Read/Write

vsDataIuBcLink

sourceIpAddressValidation

Cell Broadcast

EnumRef

Default

1/1553-HSD 101 02/7

Read/Write

vsDataIubLink

atmUserPlaneTermSubrackRef

ATM Connection

MORef

Read

vsDataIubLink

cachedRemoteCpIpAddress1

IP Transport

Real

TND

N/A

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

364 (520)

Read

vsDataIubLink

cachedRemoteCpIpAddress2

IP Transport

Real

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

controlPlaneTransportOption

IP Transport

StructRef

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

controlPlaneTransportOption.atm

ATM Connection

EnumRef

Read/Write

vsDataIubLink

controlPlaneTransportOption.ipv4

IP Transport

EnumRef

Default

Read/Write

vsDataIubLink

l2EstReqRetryTimeNbapC

Radio Protocols

Real

Default

Read/Write

vsDataIubLink

l2EstReqRetryTimeNbapD

Radio Protocols

Real

Read/Write

vsDataIubLink

remoteCpIpAddress1

IP Transport

Real

TND

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Network Parameters

365 (520)

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

remoteCpIpAddress2

IP Transport

Real

5/1553-HSD 101 02/7

Read

vsDataIubLink

sctpRef

Signalling Bearer

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

softCongThreshGbrBwDl

QoS Handling

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

softCongThreshGbrBwUl

QoS Handling

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneGbrAdmBandwidthDl

QoS Handling

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

366 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneGbrAdmBandwidthUl

QoS Handling

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneGbrAdmEnabled

QoS Handling

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneGbrAdmMarginDl

QoS Handling

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneGbrAdmMarginUl

QoS Handling

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneIpResourceRef

IP Transport

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

367 (520)

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneTransportOption

IP Transport

StructRef

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7
1/1553-HSD 101 02/7

Read/Write

vsDataIubLink

userPlaneTransportOption.atm

ATM Connection

EnumRef

Read/Write

vsDataIubLink

userPlaneTransportOption.ipv4

IP Transport

EnumRef

Read/Write

vsDataIuLink

atmUserPlaneTermSubrackRef

ATM Connection

MORef

Restricted
Read/Write

Y
N

Y
Y

N
Y

N
Y

vsDataIuLink
vsDataIuLink

id
packetDataRouterRef

TN Administration
IP Transport

Id
MORef

Read/Write

vsDataIuLink

userLabel

TN Administration

Label

Read/Write

vsDataIuLink

userPlaneIpResourceRef

IP Transport

MORef

TND
Default

TND

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

368 (520)

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write

vsDataIuLink

userPlaneTransportOption

IP Transport

StructRef

TND

Read/Write

vsDataIuLink

userPlaneTransportOption.atm

ATM Connection

EnumRef

Read/Write

vsDataIuLink

userPlaneTransportOption.ipv4

IP Transport

EnumRef

Default

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7
1/1553-HSD 101 02/7

Read/Write

vsDataIurLink

atmUserPlaneTermSubrackRef

ATM Connection

MORef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataIurLink

userPlaneIpResourceRef

IP Transport

MORef

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read/Write

vsDataIurLink

userPlaneTransportOption

IP Transport

StructRef

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Read/Write

vsDataIurLink

userPlaneTransportOption.atm

ATM Connection

EnumRef

Read/Write

vsDataIurLink

userPlaneTransportOption.ipv4

IP Transport

EnumRef

Read/Write

vsDataJ1PhysPathTerm

administrativeState

TN Administration

EnumRef

Read/Write

vsDataJ1PhysPathTerm

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataJ1PhysPathTerm

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataJ1PhysPathTerm

aisReporting

Physical Interface

Real

TND

TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

369 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

vsDataJ1PhysPathTerm

degThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataJ1PhysPathTerm

degThreshold

Physical Interface

Real

Default

Read/Write

vsDataJ1PhysPathTerm

idlePattern

Physical Interface

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

370 (520)

Default

Read/Write

vsDataJ1PhysPathTerm

idlePattern

Physical Interface

EnumRef

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataJ1PhysPathTerm
vsDataJ1PhysPathTerm

id
id

TN Administration
TN Administration

Id
Id

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataJ1PhysPathTerm
vsDataJ1PhysPathTerm

lineNo
lineNo

Physical Interface
Physical Interface

Real
Real

Default

Read/Write

vsDataJ1PhysPathTerm

loopback

Physical Interface

EnumRef

Default

Read/Write

vsDataJ1PhysPathTerm

loopback

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND

Read/Write

vsDataJ1PhysPathTerm

physicalLineType

Physical Interface

EnumRef

TND

Read/Write

vsDataJ1PhysPathTerm

physicalLineType

Physical Interface

EnumRef

TND O&M

Read/Write

vsDataJ1PhysPathTerm

rdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataJ1PhysPathTerm

rdiReporting

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read

TN Administration

MORef

Read

TN Administration

MORef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read/Write

Physical Interface

Timer

TND
TND

TND O&M

Prepared: EZIEAGA

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

vsDataJ1PhysPathTerm

Date: 2014-05-27
Sheet: 14.0.2

shutDownTimeout

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND O&M

Network Parameters

371 (520)

Read/Write

vsDataJ1PhysPathTerm

shutDownTimeout

Physical Interface

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataJ1PhysPathTerm
vsDataJ1PhysPathTerm

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

5/1553-HSD 101 02

Read/Write

vsDataLag

requiredNumberOfLinks

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataLag

requiredNumberOfLinks

IP

Real

Read
Read

N
N

Y
Y

N
N

N
N

Signalling Bearer
Signalling Bearer

MoRef
State

Default

Restricted

vsDataM3uAssociation

autoStartAssociation

Signalling Bearer

Real

Default

Read/Write

vsDataM3uAssociation

congestionAlarmThreshold

Signalling Bearer

Timer

Restricted

vsDataM3uAssociation

dscp

Signalling Bearer

Real

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

372 (520)

TND

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

localIpMask

Signalling Bearer

EnumRef

TND

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

localPortNumber

Signalling Bearer

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

id

TN Administration

Id

CPI

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

mtp3bSrsId

Signalling Bearer

MORef

Read

TN Administration

EnumRef

N/A

TND

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

remoteIpAddress1

Signalling Bearer

Real

TND

5/1553-HSD 101 02/7

Restricted

vsDataM3uAssociation

remoteIpAddress2

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

Default

CPI

5/1553-HSD 101 02/7

Network Parameters

Restricted

vsDataM3uAssociation

Read

Restricted

vsDataM3uAssociation

Read
Restricted

N
Y

Y
Y

N
N

N
N

Read/Write

remotePortNumber

373 (520)
Signalling Bearer

Real

TN Administration

MORef

role

Signalling Bearer

EnumRef

vsDataM3uAssociation

sctpId

Signalling Bearer

MoRef
MORef

vsDataM3uAssociation

userLabel

TN Administration

Label

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

documentServerAddress

IP Transport

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

documentServerAddress

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

374 (520)

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

logonServerAddress

IP Transport

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

logonServerAddress

IP Transport

Real

Default

Read/Write

IP Transport

Real

Default

Read/Write

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

375 (520)

Default

Read/Write

IP Transport

Real

Default

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

376 (520)

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

377 (520)

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

ntpServerAddressPrimary

IP Transport

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

ntpServerAddressPrimary

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

378 (520)

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

ntpServerAddressSecondary

IP Transport

Real

TND

2/1553-HSD 101 02/6

Read/Write

vsDataManagedElementData

ntpServerAddressSecondary

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

379 (520)

TND

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

TND

2/1553-HSD 101 02/6

Read/Write

IP Transport

Real

Recommended

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

Recommended

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

Recommended

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

380 (520)

Recommended

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

Default

2/1553-HSD 101 02/7

Read/Write

IP Transport

Real

N/A

Read

TN Administration

Status

TND

Read/Write

vsDataMspg

degCauseMsp

Physical Interface

Real

TND O&M

Read/Write

vsDataMspg

lockout

Physical Interface

Real

TND

Restricted

vsDataMspg

id

TN Administration

Id

N/A

Read

TN Administration

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataMspg

os155SpiStandbyId

Physical Interface

MORef

TND

1/1553-HSD 101 02/7

Restricted

vsDataMspg

os155SpiWorkingId

Physical Interface

MORef

Read

Physical Interface

MORef

Read/Write

Physical Interface

Real

TND O&M

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

381 (520)

Read

Physical Interface

MORef

Read

Physical Interface

MORef

Read

Physical Interface

EnumRef

Read/Write

TN Administration

Label

N/A

Read

TN Administration

Status

TND

Read/Write

vsDataMspgExtended

bidirectional

Physical Interface

Real

TND

Restricted

vsDataMspgExtended

id

TN Administration

Id

Read

vsDataMspgExtended

opBidirectionalMode

Physical Interface

Real

N/A

Read

TN Administration

EnumRef

TND

Restricted

Physical Interface

MORef

Prepared: EZIEAGA

vsDataMspg

vsDataMspgExtended

Date: 2014-05-27
Sheet: 14.0.2

userLabel

os155SpiProtectionRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Restricted

Read

Read/Write

Read

Read

Read/Write

Default

Read/Write

N/A

Read

TND

Prepared: EZIEAGA

Network Parameters

vsDataMspgExtended

Physical Interface

MORef

Physical Interface

Status

Physical Interface

Real

Physical Interface

MORef

Physical Interface

MORef

vsDataMspgExtended

userLabel

TN Administration

Label

vsDataMspgExtended

waitToRestoreTime

Physical Interface

Timer

TN Administration

Status

vsDataMspgExtended

Date: 2014-05-27
Sheet: 14.0.2

os155SpiWorkingRef

382 (520)

revertive

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

N/A

Network Parameters

vsDataMtp3bAp

id

383 (520)

Restricted

TN Administration

Id

Read

TN Administration

EnumRef

Read

TN Administration

MORef

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted

vsDataMtp3bAp

routeSetId

Signalling Bearer

MORef

CPI

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted

vsDataMtp3bAp

serviceInd

Signalling Bearer

Real

Read/Write

vsDataMtp3bAp

userLabel

TN Administration

Label

Default

Restricted

vsDataMtp3bSlAnsi

autoStartLink

Signalling Bearer

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read

TND

Restricted

N/A

Read

Read

Network Parameters

384 (520)
Signalling Bearer

State

TN Administration

Id

TN Administration

EnumRef

Signalling Bearer

EnumRef

vsDataMtp3bSlAnsi

id

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlAnsi

signLinkCode

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlAnsi

tpId

Signalling Bearer

MORef

Read

Signalling Bearer

EnumRef

Read/Write

vsDataMtp3bSlAnsi

userLabel

TN Administration

Label

Default

Restricted

vsDataMtp3bSlChina

autoStartLink

Signalling Bearer

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read

TND

Restricted

N/A

Read

Default

Read/Write

Read

Network Parameters

vsDataMtp3bSlChina

vsDataMtp3bSlChina

id

prioBeforeSio

385 (520)
Signalling Bearer

State

TN Administration

Id

TN Administration

EnumRef

Signalling Bearer

Real

Signalling Bearer

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlChina

signLinkCode

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlChina

tpId

Signalling Bearer

MORef

Read

Signalling Bearer

EnumRef

Read/Write

vsDataMtp3bSlChina

userLabel

TN Administration

Label

Restricted

vsDataMtp3bSlItu

autoStartLink

Signalling Bearer

Real

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Network Parameters

386 (520)

Read

TN Administration

Status

Read

Signalling Bearer

State

TND

Restricted

TN Administration

Id

N/A

Read

TN Administration

EnumRef

Default

Read/Write

Signalling Bearer

Real

Read

Signalling Bearer

EnumRef

vsDataMtp3bSlItu

vsDataMtp3bSlItu

id

prioBeforeSio

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlItu

signLinkCode

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlItu

tpId

Signalling Bearer

MORef

Read

Signalling Bearer

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Read/Write

N/A

Read

TND

Read/Write

vsDataMtp3bSls

Restricted

Restricted

Read

Read

Read

Read/Write
Default
N/A

TND
TND
N/A

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataMtp3bSlItu

TN Administration

Label

TN Administration

Status

cLinkAnsi

Signalling Bearer

Real

vsDataMtp3bSls

id

TN Administration

Id

vsDataMtp3bSls

mtp3bSrsId

Signalling Bearer

MORef

TN Administration

EnumRef

TN Administration

MORef

Signalling Bearer

EnumRef

vsDataMtp3bSls

userLabel

TN Administration

Label

Restricted

vsDataMtp3bSlTtc

autoStartLink

Signalling Bearer

Real

Read

TN Administration

Status

Date: 2014-05-27
Sheet: 14.0.2

userLabel

387 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read

TND

Restricted

N/A

Read

Default

Read/Write

Network Parameters

vsDataMtp3bSlTtc

id

vsDataMtp3bSlTtc

prioBeforeSio

388 (520)
Signalling Bearer

State

TN Administration

Id

TN Administration

EnumRef

Signalling Bearer

Real

Read

Signalling Bearer

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlTtc

signLinkCode

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataMtp3bSlTtc

tpId

Signalling Bearer

MORef

Read

Signalling Bearer

EnumRef

Read/Write

TN Administration

Label

Prepared: EZIEAGA

vsDataMtp3bSlTtc

Date: 2014-05-27
Sheet: 14.0.2

userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

Default

Read/Write

vsDataMtp3bSpAnsi

Default

Read/Write

Default

Read/Write

Default

Read/Write

TND

Restricted

Prepared: EZIEAGA

389 (520)
TN Administration

Status

m3uaNoOfAttempsOfDauds

Signalling Bearer

Real

vsDataMtp3bSpAnsi

maxSizeChangeBuf

Signalling Bearer

Real

vsDataMtp3bSpAnsi

maxSizeReroutBuf

Signalling Bearer

Real

vsDataMtp3bSpAnsi

modifiedSlsRotation

Signalling Bearer

EnumRef

vsDataMtp3bSpAnsi

id

TN Administration

Id

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Recommended

390 (520)

Read/Write

vsDataMtp3bSpAnsi

networkInd

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

nodeBehaviour

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

noOfAttempsOfAssociationEstablishment

Signalling Bearer

Real

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Read/Write

N/A

Read

Default

Read/Write

Read

Read/Write

Default

Prepared: EZIEAGA

Network Parameters

vsDataMtp3bSpAnsi

vsDataMtp3bSpAnsi

vsDataMtp3bSpAnsi

Date: 2014-05-27
Sheet: 14.0.2

noOfCongestLevelForNI

resendTfcInterval

routeSetCongestTestFlag

391 (520)
Signalling Bearer

Real

TN Administration

EnumRef

Signalling Bearer

Real

TN Administration

MORef

Signalling Bearer

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

392 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataMtp3bSpAnsi

rpuId

Signalling Bearer

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataMtp3bSpAnsi

signallingPointCode

Signalling Bearer

Real

Read/Write

vsDataMtp3bSpAnsi

sioSpare

Signalling Bearer

EnumRef

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

393 (520)

TND

Read/Write

vsDataMtp3bSpAnsi

spPriority

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioCb

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioCo

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioEc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioLink

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioRst

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioSlt

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioTfc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioTra

Signalling Bearer

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

394 (520)

Default

Read/Write

vsDataMtp3bSpAnsi

spPriority.prioUpu

Signalling Bearer

EnumRef

TND

Read/Write

vsDataMtp3bSpAnsi

spTimer

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaPeriodicAudit

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaT40

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaT42

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaTack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaTassocack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerM3uaTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerSlta

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerSltm

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT1

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT10

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

395 (520)

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT12

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT13

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT14

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT15

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT16

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT17

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT2

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT20

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT21

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT22

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT23

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT25

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT26

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT27

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT28

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

396 (520)

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT29

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT3

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT30

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT31

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT4

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT5

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT6

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerT8

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerTBsnt

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerTRetrieval

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

spTimer.timerTStart

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpAnsi

statusIndInterval

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpAnsi

testPatternSltm

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Network Parameters

397 (520)

Read/Write

vsDataMtp3bSpAnsi

transFrHandler

Signalling Bearer

EnumRef

Read/Write

vsDataMtp3bSpAnsi

userLabel

TN Administration

Label

Default

Restricted

Signalling Bearer

Real

N/A

Read

TN Administration

Status

Default

Read/Write

vsDataMtp3bSpChina

m3uaNoOfAttempsOfDauds

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpChina

maxSizeChangeBuf

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpChina

maxSizeReroutBuf

Signalling Bearer

Real

TND

Restricted

vsDataMtp3bSpChina

id

TN Administration

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Recommended

398 (520)

Read/Write

vsDataMtp3bSpChina

networkInd

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

nodeBehaviour

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

noOfAttempsOfAssociationEstablishment

Signalling Bearer

Real

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Default

Read/Write

N/A

Read

Default

Read/Write

Read

Default

Read/Write

vsDataMtp3bSpChina

Default

Read/Write

vsDataMtp3bSpChina

Prepared: EZIEAGA

vsDataMtp3bSpChina

vsDataMtp3bSpChina

Date: 2014-05-27
Sheet: 14.0.2

noOfCongestLevelForNI

399 (520)
Signalling Bearer

Real

TN Administration

EnumRef

Signalling Bearer

Real

TN Administration

MORef

restartType

Signalling Bearer

EnumRef

routeSetCongestTestFlag

Signalling Bearer

Real

resendTfcInterval

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

400 (520)

TND

1/1553-HSD 101 02/7

Read/Write

vsDataMtp3bSpChina

rpuId

Signalling Bearer

MORef

TND

1/1553-HSD 101 02/7

Read/Write

vsDataMtp3bSpChina

signallingPointCode

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpChina

sioSpare

Signalling Bearer

EnumRef

TND

Read/Write

vsDataMtp3bSpChina

spPriority

Signalling Bearer

StructRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

401 (520)

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioCb

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioCo

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioEc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioLink

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioRst

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioSlt

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioTfc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioTra

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpChina

spPriority.prioUpu

Signalling Bearer

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

402 (520)

TND

Read/Write

vsDataMtp3bSpChina

spTimer

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaPeriodicAudit

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaT40

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaT42

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaTack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaTassocack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerM3uaTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerSlta

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerSltm

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT1

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT10

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT12

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT13

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

403 (520)

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT14

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT15

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT16

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT17

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT18

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT19

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT2

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT20

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT21

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT22

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT23

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT3

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT4

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT5

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

404 (520)

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT6

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerT8

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerTBsnt

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerTRetrieval

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

spTimer.timerTStart

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpChina

statusIndInterval

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpChina

testPatternSltm

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpChina

transFrHandler

Signalling Bearer

EnumRef

Read/Write

vsDataMtp3bSpChina

userLabel

TN Administration

Label

Restricted

Signalling Bearer

Real

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

Default

Read/Write

vsDataMtp3bSpItu

Default

Read/Write

Default

Read/Write

Restricted

Read/Write

TND
Recommended

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

405 (520)
TN Administration

Status

m3uaNoOfAttempsOfDauds

Signalling Bearer

Real

vsDataMtp3bSpItu

maxSizeChangeBuf

Signalling Bearer

Real

vsDataMtp3bSpItu

maxSizeReroutBuf

Signalling Bearer

Real

vsDataMtp3bSpItu

id

TN Administration

Id

vsDataMtp3bSpItu

networkInd

Signalling Bearer

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

406 (520)

Default

Read/Write

vsDataMtp3bSpItu

nodeBehaviour

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

noOfAttempsOfAssociationEstablishment

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpItu

noOfCongestLevelForNI

Signalling Bearer

Real

N/A

Read

TN Administration

EnumRef

Default

Read/Write

Signalling Bearer

Real

Read

TN Administration

MORef

Prepared: EZIEAGA

vsDataMtp3bSpItu

Date: 2014-05-27
Sheet: 14.0.2

resendTfcInterval

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Network Parameters

407 (520)

Read/Write

vsDataMtp3bSpItu

routeSetCongestTestFlag

Signalling Bearer

Real

Read/Write

vsDataMtp3bSpItu

rpuId

Signalling Bearer

MORef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

408 (520)

Read/Write

vsDataMtp3bSpItu

signallingPointCode

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpItu

sioSpare

Signalling Bearer

EnumRef

TND

Read/Write

vsDataMtp3bSpItu

spPriority

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioCb

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioCo

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioEc

Signalling Bearer

EnumRef

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

409 (520)

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioLink

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioRst

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioSlt

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioTfc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioTra

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpItu

spPriority.prioUpu

Signalling Bearer

EnumRef

TND

Read/Write

vsDataMtp3bSpItu

spTimer

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaPeriodicAudit

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaT40

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaT42

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

410 (520)

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaTack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaTassocack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerM3uaTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerSlta

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerSltm

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT1

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT10

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT12

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT13

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT14

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT15

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT16

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

411 (520)

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT17

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT18

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT19

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT2

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT20

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT21

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT22

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT23

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT3

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT4

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT5

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT6

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

412 (520)

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerT8

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerTBsnt

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerTRetrieval

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

spTimer.timerTStart

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpItu

statusIndInterval

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpItu

testPatternSltm

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpItu

transFrHandler

Signalling Bearer

EnumRef

Read/Write

vsDataMtp3bSpItu

userLabel

TN Administration

Label

Default

Restricted

Signalling Bearer

Real

Default

Read/Write

Signalling Bearer

EnumRef

Prepared: EZIEAGA

vsDataMtp3bSpItu

Date: 2014-05-27
Sheet: 14.0.2

version

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

Default

Read/Write

vsDataMtp3bSpTtc

Default

Read/Write

Default

Read/Write

TND

Restricted

Prepared: EZIEAGA

413 (520)
TN Administration

Status

m3uaNoOfAttempsOfDauds

Signalling Bearer

Real

vsDataMtp3bSpTtc

maxSizeChangeBuf

Signalling Bearer

Real

vsDataMtp3bSpTtc

maxSizeReroutBuf

Signalling Bearer

Real

vsDataMtp3bSpTtc

id

TN Administration

Id

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

414 (520)

Default

Read/Write

vsDataMtp3bSpTtc

nodeBehaviour

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpTtc

noOfAttempsOfAssociationEstablishment

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpTtc

noOfCongestLevelForNI

Signalling Bearer

Real

N/A

Read

TN Administration

EnumRef

Default

Read/Write

Signalling Bearer

Real

Read

TN Administration

MORef

Prepared: EZIEAGA

vsDataMtp3bSpTtc

Date: 2014-05-27
Sheet: 14.0.2

resendTfcInterval

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

415 (520)

Read/Write

vsDataMtp3bSpTtc

routeSetCongestTestFlag

Signalling Bearer

Real

Read/Write

vsDataMtp3bSpTtc

rpuId

Signalling Bearer

MORef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

416 (520)

Read/Write

vsDataMtp3bSpTtc

signallingPointCode

Signalling Bearer

Real

TND

Read/Write

vsDataMtp3bSpTtc

spPriority

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioCb

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioCo

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioEc

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioRst

Signalling Bearer

EnumRef

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioRt

Signalling Bearer

EnumRef

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

417 (520)

Default

Read/Write

vsDataMtp3bSpTtc

spPriority.prioTfc

Signalling Bearer

EnumRef

TND

Read/Write

vsDataMtp3bSpTtc

spTimer

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerSrt

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT1

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT10

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT15

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT16

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT17

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT2

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT3

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT4

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT6

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerT8

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

418 (520)

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerTBsnt

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerTRetrieval

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimer.timerTStart

Signalling Bearer

Timer

TND

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua

Signalling Bearer

StructRef

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaPeriodicAudit

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT1

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT3

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT40

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT41

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT42

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT6

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaT8

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaTack

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

419 (520)

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaTassocack

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

spTimerM3ua.timerM3uaTc

Signalling Bearer

Timer

Default

Read/Write

vsDataMtp3bSpTtc

statusIndInterval

Signalling Bearer

Real

Default

Read/Write

vsDataMtp3bSpTtc

testPatternSltm

Signalling Bearer

Real

Read/Write

vsDataMtp3bSpTtc

userLabel

TN Administration

Label

Default

Restricted

Signalling Bearer

Real

N/A

Read

TN Administration

Status

Restricted

vsDataMtp3bSr

linkSetM3uId

Signalling Bearer

MORef

Restricted

vsDataMtp3bSr

id

TN Administration

Id

TND
TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Read

Read/Write

Read

Read

Read/Write

Read

Network Parameters

420 (520)
TN Administration

EnumRef

Signalling Bearer

Real

Signalling Bearer

EnumRef

Signalling Bearer

EnumRef

TN Administration

Label

Signalling Bearer

EnumRef

vsDataMtp3bSr

vsDataMtp3bSr

priority

userLabel

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted

vsDataMtp3bSrs

destPointCode

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Restricted

vsDataMtp3bSrs

id

TN Administration

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Read

Default

Read/Write

Read

Read/Write

TND

Restricted

TND

Restricted

Restricted
Restricted
Read/Write
Read/Write
Read

Y
Y
N
N
N

Restricted
Read/Write
Read/Write

TND

Default

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

421 (520)
TN Administration

EnumRef

Signalling Bearer

EnumRef

TN Administration

MORef

TN Administration

Label

IP Transport

MORef

IP Transport

MORef

Y
Y
Y
Y
N

N
N
Y
Y
N

N
N
N
N
N

TN Administration
TN Admnistration
TN Administration
TN Admnistration
Radio Protocols

Id
Id
Label
Id
EnumRef

vsDataNbapCommon

activeUniSaalTpRef

Radio Protocols

MORef

vsDataNbapCommon

administrativeState

TN Administration

EnumRef

vsDataNbapCommon

auditRetransmissionT

Radio Protocols

Timer

vsDataMtp3bSrs

vsDataMtp3bSrs

Date: 2014-05-27
Sheet: 14.0.2

preferredBearer

userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

422 (520)

Read

TN Administration

Status

Read

TN Administration

Status

Default

Read/Write

vsDataNbapCommon

l2EstablishReqRetryT

Radio Protocols

Timer

Default

Read/Write

vsDataNbapCommon

l2EstablishSupervisionT

Radio Protocols

Timer

Default

Read/Write

vsDataNbapCommon

l3EstablishSupervisionT

Radio Protocols

Timer

TND
TND

Restricted
Restricted
Read

Y
Y
N

Y
Y
N

N
N
N

N
N
N

vsDataNbapCommon
vsDataNbapCommon

id
id

TN Administration
TN Administration
TN Administration

Id
Id
EnumRef

Read

TN Administration

EnumRef

5/1553-HSD 101 02/7

Read

Radio Protocols

MORef

1/1553-HSD 101 02/7

Restricted

Radio Protocols

MORef

TND

Prepared: EZIEAGA

vsDataNbapCommon

Date: 2014-05-27
Sheet: 14.0.2

standbyUniSaalTpRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

423 (520)

TND

Read/Write

vsDataNbapCommon

uniSaalTpRef1

Radio Protocols

MORef

TND

Read/Write

vsDataNbapCommon

uniSaalTpRef2

Radio Protocols

MORef

N/A

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataNbapCommon
vsDataNbapCommon

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read

Radio Protocols

EnumRef

Restricted

vsDataNbapDedicated

activeUniSaalTpRef

Radio Protocols

MORef

Read/Write

vsDataNbapDedicated

administrativeState

TN Administration

EnumRef

Read

TN Administration

Status

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

Read

Default

Read/Write

vsDataNbapDedicated

Default

Read/Write

TND
TND

Restricted
Restricted
Read

Y
Y
N

Y
Y
N

N
N
N

N
N
N

Read

5/1553-HSD 101 02/7

Read

1/1553-HSD 101 02/7

Restricted

vsDataNbapDedicated

standbyUniSaalTpRef

TND

Read/Write

vsDataNbapDedicated

TND

Read/Write

N/A

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

Read/Write

TND

Prepared: EZIEAGA

424 (520)
TN Administration

Status

l2EstablishReqRetryT

Radio Protocols

Timer

vsDataNbapDedicated

l2EstablishSupervisionT

Radio Protocols

Timer

vsDataNbapDedicated
vsDataNbapDedicated

id
id

TN Administration
TN Administration
TN Administration

Id
Id
EnumRef

TN Administration

EnumRef

Radio Protocols

MORef

Radio Protocols

MORef

uniSaalTpRef1

Radio Protocols

MORef

vsDataNbapDedicated

uniSaalTpRef2

Radio Protocols

MORef

vsDataNbapDedicated
vsDataNbapDedicated

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

425 (520)

Read/Write

TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataNniSaalProfile

id

TN Administration

Id

TND

Restricted

vsDataNniSaalProfile

profileData

Signalling Bearer

StructRef

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.congestionLevel1Abatement

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.congestionLevel1OnSet

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.congestionLevel2Abatement

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.congestionLevel2OnSet

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.congestionLevel3Abatement

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.congestionLevel3OnSet

Signalling Bearer

Real

Default

Restricted

vsDataNniSaalProfile

profileData.discardMessagesLevel1

Signalling Bearer

Real

Default

Restricted

vsDataNniSaalProfile

profileData.discardMessagesLevel2

Signalling Bearer

Real

Default

Default

1/1553-HSD 101 02/7

Default

Default

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

CPI

1/1553-HSD 101 02/7

Default

Network Parameters

426 (520)

Restricted

vsDataNniSaalProfile

profileData.discardMessagesLevel3

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.initialCredit

Signalling Bearer

Real

Restricted

vsDataNniSaalProfile

profileData.maxCC

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.maxNRP

Signalling Bearer

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.maxPD

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.maxStat

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.mps

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

427 (520)

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.nrOfPDUsDuringProving

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerCC

Signalling Bearer

Timer

CPI

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerIdle

Signalling Bearer

Timer

CPI

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerKeepAlive

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerNoCredit

Signalling Bearer

Timer

CPI

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerNoResponse

Signalling Bearer

Timer

CPI

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerPoll

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerRepeatSrec

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerT1

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

428 (520)

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerT2

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalProfile

profileData.timerT3

Signalling Bearer

Timer

Read

TN Administration

MORef

Read/Write

vsDataNniSaalProfile

userLabel

TN Administration

Label

TND

1/1553-HSD 101 02/7

Restricted

vsDataNniSaalTp

aal5TpVccTpId

Signalling Bearer

MORef

Recommended

1/1553-HSD 101 02/7

Read/Write

vsDataNniSaalTp

maxSduSize

Signalling Bearer

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataNniSaalTp

nniSaalProfileId

Signalling Bearer

MORef

TND

Restricted

vsDataNniSaalTp

id

TN Administration

Id

N/A

Read

TN Administration

EnumRef

Read

TN Administration

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

429 (520)

Read/Write

vsDataNniSaalTp

userLabel

TN Administration

Label

Read/Write

vsDataNodeBFunction

nbapDscp

Radio Protocols

Real

Read/Write

vsDataOs155SpiTtp

administrativeState

TN Administration

EnumRef

Read/Write

vsDataOs155SpiTtp

administrativeState

TN Administration

EnumRef

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND

5/1553-HSD 101 02/7

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

lineNo

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

lineNo

Physical Interface

Real

Default

Read/Write

vsDataOs155SpiTtp

loopBack

Physical Interface

EnumRef

Default

Read/Write

vsDataOs155SpiTtp

loopBack

Physical Interface

EnumRef

TND O&M

Read/Write

vsDataOs155SpiTtp

msAisReporting

Physical Interface

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

430 (520)

TND O&M

Read/Write

vsDataOs155SpiTtp

msAisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msRdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

msRdiReporting

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

muxMode

Physical Interface

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

muxMode

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

TN Administration
TN Administration

Id
Id

Prepared: EZIEAGA

vsDataOs155SpiTtp
vsDataOs155SpiTtp

Date: 2014-05-27
Sheet: 14.0.2

id
id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

431 (520)

Default

Read/Write

vsDataOs155SpiTtp

poissonDegThreshold

Physical Interface

Real

Default

Read/Write

vsDataOs155SpiTtp

poissonDegThreshold

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Read

TN Administration

MORef

Read

TN Administration

MORef

Read

vsDataOs155SpiTtp

sfpInformation

Physical interface

StructRef

Read

vsDataOs155SpiTtp

sfpInformation

Physical interface

StructRef

TND
TND

Read
Read

N
N

N
N

N
N

N
N

vsDataOs155SpiTtp
vsDataOs155SpiTtp

sfpInformation.sfpProductNumber
sfpInformation.sfpProductNumber

Physical interface
Physical interface

Real
Real

TND

Read

vsDataOs155SpiTtp

sfpInformation.sfpState

Physical interface

EnumRef

TND

Read

vsDataOs155SpiTtp

sfpInformation.sfpState

Physical interface

EnumRef

TND

Read

vsDataOs155SpiTtp

sfpInformation.sfpType

Physical interface

Real

TND

Read

vsDataOs155SpiTtp

sfpInformation.sfpType

Physical interface

Real

Read

vsDataOs155SpiTtp

sfpPort

Physical interface

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

432 (520)

Read

vsDataOs155SpiTtp

sfpPort

Physical interface

Real

TND O&M

Read/Write

vsDataOs155SpiTtp

shutDownTimeout

Physical Interface

Timer

TND O&M

Read/Write

vsDataOs155SpiTtp

shutDownTimeout

Physical Interface

Timer

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

standardMode

Physical Interface

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataOs155SpiTtp

standardMode

Physical Interface

EnumRef

Default

Read/Write

vsDataOs155SpiTtp

supervisionMode

Physical Interface

EnumRef

Default

Read/Write

vsDataOs155SpiTtp

supervisionMode

Physical Interface

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataOs155SpiTtp
vsDataOs155SpiTtp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

2/1553-HSD 101 02/6

Read/Write

TN Administration

EnumRef

2/1553-HSD 101 02/6

Read/Write

TN Administration

EnumRef

Read

TN Administration

Status

N/A

Prepared: EZIEAGA

vsDataOspf

Date: 2014-05-27
Sheet: 14.0.2

administrativeState

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Read

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

N/A

Read

N/A

Read

Read

Read

TND

TND

TND O&M
TND O&M
TND

Prepared: EZIEAGA

2/1553-HSD 101 02/6


2/1553-HSD 101 02/6

Network Parameters

433 (520)
TN Administration

Status

IP O&M
IP O&M

MORef
MORef

TN Administration

EnumRef

TN Administration

EnumRef

IP O&M

Status

IP O&M

Status

Read/Write

IP O&M

Status

Read/Write

vsDataOspf

ospfASBdrRtrStatus

IP O&M

Status

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataOspf

id

TN Administration
TN Administration

Id
Id

Read/Write

IP O&M

Id

vsDataOspf

Date: 2014-05-27
Sheet: 14.0.2

ipMo

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

vsDataOspf

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataOspf

TND

Restricted

TND

Restricted

Read

Read

TND

Read/Write

TND

Read/Write

vsDataOspfArea

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

TND
TND

Restricted
Restricted

N
N

Y
Y

N
N

TND
TND

Restricted
Restricted

N
N

Y
Y

TND

Restricted

TND

Restricted

TND O&M
TND O&M

Prepared: EZIEAGA

2/1553-HSD 101 02/6


2/1553-HSD 101 02/6

vsDataOspf

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

topoDbStoreInterv

IP O&M

Real

userLabel

TN Administration
TN Administration

Label
Label

IP O&M

Id

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

importExternalLsa

IP O&M

Real

vsDataOspfArea

id

TN Administration
TN Administration

Id
Id

N
N

vsDataOspfArea

range0

IP O&M
IP O&M

StructRef
StructRef

N
N

N
N

vsDataOspfArea

range0.advertise

IP O&M
IP O&M

Real
Real

IP O&M

Real

IP O&M

Real

vsDataOspf

vsDataOspfArea

vsDataOspfArea

vsDataOspfArea

Date: 2014-05-27
Sheet: 14.0.2

ospfRouterId

434 (520)

recoverTopoDb

areaId

areaLsaChecksum

range0.ipAddress

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND

Restricted

TND

Restricted

vsDataOspfArea

Read
Read

N
N

Y
Y

Y
Y

N
N

Read
Read

N
N

Y
Y

Y
Y

N
N

Read

Read

Read

Prepared: EZIEAGA

435 (520)
IP O&M

Real

range0.subnetMask

IP O&M

Real

vsDataOspfArea

range1

IP O&M
IP O&M

StructRef
StructRef

vsDataOspfArea

range1.advertise

IP O&M
IP O&M

Real
Real

IP O&M

Real

vsDataOspfArea

range1.ipAddress

IP O&M

Real

IP O&M

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

436 (520)

Read

vsDataOspfArea

range1.subnetMask

IP O&M

Real

Read
Read

N
N

Y
Y

Y
Y

N
N

vsDataOspfArea

range2

IP O&M
IP O&M

StructRef
StructRef

Read
Read

N
N

Y
Y

Y
Y

N
N

vsDataOspfArea

range2.advertise

IP O&M
IP O&M

Real
Real

Read

IP O&M

Real

Read

IP O&M

Real

Read

IP O&M

Real

Read

IP O&M

Real

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

TND

Read/Write

IP O&M

Real

TND

Read/Write

IP O&M

Real

Prepared: EZIEAGA

vsDataOspfArea

vsDataOspfArea

vsDataOspfArea

Date: 2014-05-27
Sheet: 14.0.2

range2.ipAddress

range2.subnetMask

sendAreaSummary

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND
TND

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

vsDataOspfArea

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataOspfArea

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

TND

Read/Write

Prepared: EZIEAGA

vsDataOspfArea

vsDataOspfArea

vsDataOspfInterface

vsDataOspfInterface

vsDataOspfInterface

Date: 2014-05-27
Sheet: 14.0.2

437 (520)
IP O&M
IP O&M

Real
Real

IP O&M

Real

IP O&M

Real

IP O&M

EnumRef

stubAreaMetricType

IP O&M

EnumRef

userLabel

TN Administration
TN Administration

Label
Label

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

IP O&M

Real

stubArea

stubAreaMetric

helloInterval

interfacePriority

interfaceTransitDelay

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND

Read/Write

TND

Read/Write

TND

Read/Write

vsDataOspfInterface

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataOspfInterface

TND

Restricted

TND

Restricted

TND

Read/Write

TND

Read/Write

vsDataOspfInterface

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

Restricted

Read/Write

Read

Restricted

Read

TND O&M
TND O&M

TND

TND

Prepared: EZIEAGA

2/1553-HSD 101 02/6


2/1553-HSD 101 02/6

vsDataOspfInterface

IP O&M

Real

IP O&M

MORef

ospfAreaRelated

IP O&M

MORef

id

TN Administration
TN Administration

Id
Id

IP O&M

MORef

IP O&M

MORef

IP O&M

Real

routerDeadInterval

IP O&M

Real

vsDataOspfInterface

userLabel

TN Administration
TN Administration

Label
Label

vsDataPacketDataRouter

aal5TpRef

IP Transport

MORef

vsDataPacketDataRouter

administrativeState

TN Administration

EnumRef

TN Administration

Status

IP Transport

Real

TN Administration

EnumRef

vsDataOspfInterface

vsDataPacketDataRouter

Date: 2014-05-27
Sheet: 14.0.2

lsaTransmissionInterval

438 (520)

relatedLink

cnIuLinkIpAddress

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Network Parameters

Restricted

Read

TND

Restricted

vsDataPacketDataRouter

Default

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

Read/Write

Read

Read

vsDataPacketFrequencySyncRef

cachedIpAddress

Real

Read/Write
Read/Write

N
Y

Y
Y

Y
Y

N
N

vsDataPacketFrequencySyncRef
vsDataPacketFrequencySyncRef

dscp
ipAccessHostEtRef

Real
MORef

Read

Restricted

Prepared: EZIEAGA

vsDataPacketDataRouter

id

439 (520)
TN Administration

Id

TN Administration

MORef

rncIpAddress

IP Transport

Real

vsDataPacketDataRouter
vsDataPacketDataRouter

timeToLive
userLabel

IP Transport
TN Administration

Real
Label

vsDataPacketFrequencySyncRef

administrativeState

EnumRef

Status

EnumRef
vsDataPacketFrequencySyncRef

Date: 2014-05-27
Sheet: 14.0.2

id

Id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

440 (520)

Read

Real

Read/Write

vsDataPacketFrequencySyncRef

ptpDomain

Real

Read
Read
Read

N
N
N

N
Y
Y

N
Y
Y

N
N
N

vsDataPacketFrequencySyncRef
vsDataPacketFrequencySyncRef

ptpOwnPortIdentity
ptpOwnPortIdentity.clockIdentity

Real
StructRef
Real

Read
Read
Read

N
N
N

Y
N
N

Y
N
N

N
N
N

vsDataPacketFrequencySyncRef

ptpOwnPortIdentity.ptpPortNumber

Read
Read
Read

N
N
N

N
N
Y

N
N
N

N
N
Y

Real
StructRef
Real

Real
Real
MORef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Recommended

Default

Prepared: EZIEAGA

Network Parameters

441 (520)

Read/Write

vsDataPacketFrequencySyncRef

serverAddress

Real

Read/Write
Read/Write
Restricted
Read/Write

N
N
Y
N

Y
Y
Y
Y

Y
Y
N
Y

N
N
N
N

vsDataPacketFrequencySyncRef

userLabel

Label

vsDataPmService

maxNoOfCounters

O&M PM Statistics

Real

116/1553-HSD 101 02/7 Read/Write

vsDataPmService

minorAlarmCeasingDelta

O&M PM Statistics

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

116/1553-HSD 101 02/7 Read/Write

N/A

116/1553-HSD 101 02/7 Read

N/A

116/1553-HSD 101 02/7 Read

Default

116/1553-HSD 101 02/7 Read/Write

Recommended

116/1553-HSD 101 02/7 Read/Write

Network Parameters

vsDataPmService

minorAlarmCeasingDelta

442 (520)
O&M PM Statistics

Real

O&M PM Statistics

Real

O&M PM Statistics

Real

vsDataPmService

performanceDataVolume

O&M PM Statistics

Real

vsDataPmService

performanceDataVolume

O&M PM Statistics

Real

N/A

Restricted

vsDataPmService

id

TN Administration

Id

N/A

Restricted

vsDataPmService

id

TN Administration

Id

Default

116/1553-HSD 101 02/7 Read/Write

vsDataPmService

warningAlarmCeasingDelta

O&M PM Statistics

Real

Default

116/1553-HSD 101 02/7 Read/Write

vsDataPmService

warningAlarmCeasingDelta

O&M PM Statistics

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

443 (520)

Default

116/1553-HSD 101 02/7 Read/Write

vsDataPmService

warningAlarmLimitPercent

O&M PM Statistics

Real

Default

116/1553-HSD 101 02/7 Read/Write

vsDataPmService

warningAlarmLimitPercent

O&M PM Statistics

Real

Read

Read

Restricted
Read

Y
N

Y
N

N
Y

N
N

TN Administration

Status

Restricted

Radio Protocols

EnumRef

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataRanap

Date: 2014-05-27
Sheet: 14.0.2

cnDomainInd

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

444 (520)

TND

1/1553-HSD 101 02/7

Restricted

vsDataRanap

cnId

Radio Protocols

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataRanap

localSccpApRef

Radio Protocols

MORef

Read/Write

vsDataRanap

maxResetResourceMessageSize

Radio Protocols

Real

Read/Write

vsDataRanap

networkResourceIdentifier

Radio Protocols

Real

Read/Write

vsDataRanap

noOfResetSendings

Radio Protocols

Real

Read

TN Administration

EnumRef

Read/Write

vsDataRanap

overloadCtrlEnabled

Radio Protocols

EnumRef

Read/Write

vsDataRanap

overloadCtrlSupervision

Radio Protocols

StructRef

Recommended

Read/Write

vsDataRanap

overloadCtrlSupervision.msgIntervalTimeMi Radio Protocols


n

Timer

Recommended

Read/Write

vsDataRanap

overloadCtrlSupervision.reductionStepHold Radio Protocols


Time

Timer

TND

Restricted

vsDataRanap

id

Id

Default
TND

Default

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

TN Administration

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

445 (520)

Default

79/1553-HSD 101 02/10 Read/Write

vsDataRanap

ranapResetResourceMonitorPeriod

Fault Management

Real

Recommended

79/1553-HSD 101 02/10 Read/Write

vsDataRanap

ranapResetResourceMonitorThresh

Fault Management

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataRanap

relativeCapacity

Radio Protocols

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataRanap

remoteSccpApRef

Radio Protocols

MORef

Read/Write

vsDataRanap

resetAckGuardT

Radio Protocols

Real

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

446 (520)

Default

Read/Write

vsDataRanap

resetResendT

Radio Protocols

Real

Default

Read/Write

vsDataRanap

sccpDisabledT

Radio Protocols

Timer

Read/Write

vsDataRanap

userLabel

TN Administration

Label

Read/Write

vsDataRanap

userOutOfServiceT

Radio Protocols

Timer

Read/Write

vsDataRncFunction

intraNodeIpResourceRef

IP Transport

MORef

Read/Write

vsDataRncFunction

nbapAuditInterval

Radio Protocols

Timer

Read/Write

vsDataRncFunction

nbapDscp

IP Transport

Real

Default

TND

5/1553-HSD 101 02/7

Default

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

TND

1/1553-HSD 101 02/7

Read

Restricted

Read

vsDataRnsap

Network Parameters

localSccpApRef

447 (520)
TN Administration

Status

Radio Protocols

MORef

TN Administration

EnumRef

TND

1/1553-HSD 101 02/7

Restricted

vsDataRnsap

remoteSccpApRef

Radio Protocols

MORef

TND
Default

1/1553-HSD 101 02/7

Restricted
Read/Write

Y
N

Y
Y

N
Y

N
N

vsDataRnsap
vsDataRnsap

id
sccpDisabledT

TN Administration
Radio Protocols

Id
Timer

Read/Write

vsDataRnsap

userLabel

TN Administration

Label

Read/Write

vsDataRnsap

userOutOfServiceT

Radio Protocols

Timer

Restricted
Read

Y
N

Y
N

N
N

N
N

TN Administration

Status

Default

N/A

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

N/A

TND
CPI

Recommended

N/A

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Network Parameters

448 (520)

Read/Write

vsDataSccpApLocal

enablePoolProxyExtension

Signalling Bearer

Real

Read/Write

vsDataSccpApLocal

maxConn

Signalling Bearer

Real

Read

TN Administration

EnumRef

Read

TN Administration

MORef

Restricted

vsDataSccpApLocal

id

TN Administration

Id

Read/Write

vsDataSccpApLocal

ssN

Signalling Bearer

Real

Read/Write

vsDataSccpApLocal

userLabel

TN Administration

Label

Read/Write

vsDataSccpApLocal

useS1

Signalling Bearer

Real

Read

TN Administration

Status

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

N/A

TND
CPI

TND

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7
1/1553-HSD 101 02/7
5/1553-HSD 101 02/7

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Network Parameters

vsDataSccpApRemote

mtp3bApId

449 (520)

Restricted

Signalling Bearer

MORef

Read

TN Administration

EnumRef

Read

TN Administration

MORef

Restricted

vsDataSccpApRemote

id

TN Administration

Id

Restricted

vsDataSccpApRemote

ssN

Signalling Bearer

Real

Read/Write

vsDataSccpApRemote

userLabel

TN Administration

Label

Restricted

vsDataSccpScrc

id

TN Administration

Id

Read/Write

vsDataSccpScrc

userLabel

TN Administration

Label

Default

Read/Write

vsDataSccpSp

hopCounterSclc

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

hopCounterScoc

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

lowerConnThres

Signalling Bearer

Real

Restricted

vsDataSccpSp

mtp3bSpId

Signalling Bearer

MORef

Read

TN Administration

EnumRef

TND
N/A

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

450 (520)

Default

Read/Write

vsDataSccpSp

prioGeneral

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

prioIT

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

prioRLSD

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

prioSST

Signalling Bearer

Real

Read

TN Administration

MORef

Restricted

TN Administration

Id

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7


5/1553-HSD 101 02/7

vsDataSccpSp

Date: 2014-05-27
Sheet: 14.0.2

id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

451 (520)

Default

Read/Write

vsDataSccpSp

smiValue

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

swapUDTPointer

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

tCong

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tconnEst

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tconnResp

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tIar

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tIas

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

452 (520)

Default

Read/Write

vsDataSccpSp

tReass

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tRel

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

tStatInfo

Signalling Bearer

Timer

Default

Read/Write

vsDataSccpSp

upperConnThres

Signalling Bearer

Real

Read/Write

vsDataSccpSp

userLabel

TN Administration

Label

TND

Read/Write

vsDataSccpSp

useSCMG

Signalling Bearer

StructRef

Default

Read/Write

vsDataSccpSp

useSCMG.allowRemoteBroadcast

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

useSCMG.initiateTimerTcon

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

useSCMG.sendSSA

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

453 (520)

Default

Read/Write

vsDataSccpSp

useSCMG.sendSSP

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

useSCMG.sendSST

Signalling Bearer

Real

Default

Read/Write

vsDataSccpSp

useSCMG.useSST

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

allowedIncrementCookieLife

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

allowedIncrementCookieLife

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

454 (520)

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

associationMaxRtx

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

associationMaxRtx

Signalling Bearer

Real

Read

TN Administration

Status

N/A

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
N/A

Read

Default

Read/Write

vsDataSctp

Default

Read/Write

Default

Read/Write

Default

Read/Write

Recommended

Read/Write

Prepared: EZIEAGA

Network Parameters

455 (520)
TN Administration

Status

bundlingActivated

Signalling Bearer

EnumRef

vsDataSctp

bundlingActivated

Signalling Bearer

EnumRef

vsDataSctp

bundlingTimer

Signalling Bearer

Timer

vsDataSctp

bundlingTimer

Signalling Bearer

Timer

vsDataSctp

heartbeatInterval

Signalling Bearer

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Recommended

5/1553-HSD 101 02/7

Network Parameters

456 (520)

Read/Write

vsDataSctp

heartbeatInterval

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

heartbeatMaxBurst

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

heartbeatMaxBurst

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02

Read/Write

vsDataSctp

heartbeatPathProbingInterval

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02

Read/Write

vsDataSctp

heartbeatPathProbingInterval

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

heartbeatStatus

Signalling Bearer

Status

Default

Read/Write

vsDataSctp

heartbeatStatus

Signalling Bearer

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

457 (520)

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

initialAdRecWin

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

initialAdRecWin

Signalling Bearer

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

initialRto

Signalling Bearer

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

initialRto

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

intervalOobPkts

Signalling Bearer

Timer

Default

Read/Write

vsDataSctp

intervalOobPkts

Signalling Bearer

Timer

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

ipAccessHostGpbId

Signalling Bearer

Id

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

ipAccessHostGpbId

Signalling Bearer

MORef

Read/Write

vsDataSctp

ipAccessSctpRef

Signalling Bearer

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

5/1553-HSD 101 02/7

Network Parameters

458 (520)

Read/Write

vsDataSctp

ipAccessSctpRef

Signalling Bearer

MORef

Default

Read/Write

vsDataSctp

keyChangePeriod

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

keyChangePeriod

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxBurst

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxBurst

Signalling Bearer

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

maximumRto

Signalling Bearer

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

maximumRto

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxIncomingStream

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxIncomingStream

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

459 (520)

Default

Read/Write

vsDataSctp

maxInitialRtrAtt

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxInitialRtrAtt

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxOutgoingStream

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxOutgoingStream

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxShutDownRtrAtt

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

maxShutDownRtrAtt

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

Date: 2014-05-27
Sheet: 14.0.2

Network Parameters
maxUserDataSize

460 (520)
Signalling Bearer

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

461 (520)

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

maxUserDataSize

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

mBuffer

Signalling Bearer

Real

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

mBuffer

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

462 (520)

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

minimumRto

Signalling Bearer

Real

Default

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

minimumRto

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

nPercentage

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

nPercentage

Signalling Bearer

Real

Read/Write

vsDataSctp

nThreshold

Signalling Bearer

Real

Recommended

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Recommended

463 (520)

Read/Write

vsDataSctp

nThreshold

Signalling Bearer

Real

Recommended

Restricted

vsDataSctp

numberOfAssociations

Signalling Bearer

Real

TND

Restricted

vsDataSctp

numberOfAssociations

Signalling Bearer

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read/Write

Signalling Bearer

Real

Recommended

Prepared: EZIEAGA

5/1553-HSD 101 02/7

Network Parameters

5/1553-HSD 101 02/7

vsDataSctp

Date: 2014-05-27
Sheet: 14.0.2

pathMaxRtx

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

464 (520)

Recommended

5/1553-HSD 101 02/7

Read/Write

vsDataSctp

pathMaxRtx

Signalling Bearer

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSctp

pathSelection

Signalling Bearer

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataSctp

pathSelection

Signalling Bearer

EnumRef

Read/Write

vsDataSctp

potentiallyFailedMaxRtx

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Read/Write

vsDataSctp

N
N
Y

Y
Y
Y

N
N
N

Y
Y
N

vsDataSctp

Network Parameters

465 (520)

potentiallyFailedMaxRtx

Real

TND

5/1553-HSD 101 02/7

Read
Read
Restricted

TND

5/1553-HSD 101 02/7

Restricted

vsDataSctp

rpuId

Signalling Bearer

MORef

Default

Read/Write

vsDataSctp

rtoAlphaIndex

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

rtoAlphaIndex

Signalling Bearer

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

rpuId

TN Administration
TN Administration
Signalling Bearer

MORef
MORef
Id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

466 (520)

Default

Read/Write

vsDataSctp

rtoBetaIndex

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

rtoBetaIndex

Signalling Bearer

Real

Read/Write

vsDataSctp

sctpAssocDeleteTimeout

Real

Read/Write

vsDataSctp

sctpAssocDeleteTimeout

Real

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataSctp
vsDataSctp

id
id

TND
TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7


5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

TN Administration
TN Administration

Id
Id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

467 (520)

Read/Write

vsDataSctp

switchbackMaxThreshold

Real

Read/Write

vsDataSctp

switchbackMaxThreshold

Real

Read/Write

vsDataSctp

switchbackMinThreshold

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

468 (520)

Read/Write

vsDataSctp

switchbackMinThreshold

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSctp

switchbackMode

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataSctp

switchbackMode

EnumRef

Default

Read/Write

vsDataSctp

tSack

Signalling Bearer

Real

Default

Read/Write

vsDataSctp

tSack

Signalling Bearer

Real

Default

Read/Write
Read/Write
Read/Write

N
N
N

Y
Y
Y

Y
Y
Y

N
N
N

vsDataSctp
vsDataSctp
vsDataSctp

userLabel
userLabel
validCookieLife

TN Administration
TN Administration
Signalling Bearer

Label
Label
Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Prepared: EZIEAGA

vsDataSctp

Network Parameters

Read/Write

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

N
N
N

MORef
MORef
Real

Read

Real

Read

EnumRef

Read

EnumRef

Read

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

validCookieLife

469 (520)
Signalling Bearer

Timer

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

470 (520)

Read

EnumRef

Read

Real

Read

Real

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

N
N
N

Real
Real
Real

Read

Real

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

N
N
N

Real
Real
Real

Read

Real

Read

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

471 (520)

Read

EnumRef

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

N
N
N

Real
Real
Real

Read

Real

Read
Read
Read

N
N
N

Y
Y
Y

N
N
N

N
N
N

Real
Real
Real

Read

Real

Y
Y
N
N
N
Y
N

Y
Y
Y
Y
Y
Y
Y

N
N
N
N
Y
N
Y

N
N
N
N
N
N
N

Id
Id
MORef
MORef

TND O&M

Restricted
Restricted
Read
Read
Read/Write
Restricted
Read/Write

vsDataSts1SpeTtp

aisPReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataSts1SpeTtp

aisPReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

TND O&M

Read/Write

vsDataSts1SpeTtp

TND O&M

Read/Write

vsDataSts1SpeTtp

N/A

Read

N/A

Read

TND O&M

Read/Write

TND O&M

Read/Write

Prepared: EZIEAGA

472 (520)
TN Administration

Status

expectedPathTrace

Physical Interface

Real

expectedPathTrace

Physical Interface

Real

TN Administration

EnumRef

TN Administration

EnumRef

vsDataSts1SpeTtp

rdiPReporting

Physical Interface

Real

vsDataSts1SpeTtp

rdiPReporting

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Restricted

vsDataSts1SpeTtp

id

TN Administration

Id

Restricted

vsDataSts1SpeTtp

id

TN Administration

Id

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

473 (520)

TND O&M

Read/Write

vsDataSts1SpeTtp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataSts1SpeTtp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataSts1SpeTtp

transmittedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataSts1SpeTtp

transmittedPathTrace

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataSts1SpeTtp
vsDataSts1SpeTtp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND O&M

Read/Write

vsDataSts3CspeTtp

aisPReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataSts3CspeTtp

aisPReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

TND O&M

Read/Write

vsDataSts3CspeTtp

TND O&M

Read/Write

vsDataSts3CspeTtp

N/A

Read

N/A

Read

TND O&M

Read/Write

TND O&M

Read/Write

Prepared: EZIEAGA

474 (520)
TN Administration

Status

expectedPathTrace

Physical Interface

Real

expectedPathTrace

Physical Interface

Real

TN Administration

EnumRef

TN Administration

EnumRef

vsDataSts3CspeTtp

rdiPReporting

Physical Interface

Real

vsDataSts3CspeTtp

rdiPReporting

Physical Interface

Real

Read

TN Administration

MORef

Read

TN Administration

MORef

Restricted

TN Administration

Id

vsDataSts3CspeTtp

Date: 2014-05-27
Sheet: 14.0.2

id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

475 (520)

Restricted

vsDataSts3CspeTtp

id

TN Administration

Id

TND O&M

Read/Write

vsDataSts3CspeTtp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataSts3CspeTtp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataSts3CspeTtp

transmittedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataSts3CspeTtp

transmittedPathTrace

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataSts3CspeTtp
vsDataSts3CspeTtp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND

Read

IP Transport

Real

TND

Read

IP Transport

Real

TND
TND

Read
Read
Restricted
Restricted
Read/Write
Read/Write
Read
Read

N
N
Y
Y
N
N
N
N

Y
Y
Y
Y
Y
Y
Y
Y

Y
Y
N
N
Y
Y
Y
Y

N
N
N
N
N
N
N
N

vsDataSwitchInternalLinkPort
vsDataSwitchInternalLinkPort
vsDataSwitchInternalLinkPort
vsDataSwitchInternalLinkPort
vsDataSwitchPortStp
vsDataSwitchPortStp

id
id
userLabel
userLabel
actualPathCost
actualPathCost

IP Transport
IP Transport
TN Administration
TN Administration
TN Administration
TN Administration
IP Transport
IP Transport

MORef
MORef
Id
Id
Label
Label
Real
Real

Read/Write

vsDataSwitchPortStp

configuredPathCost

IP Transport

Real

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

476 (520)

Default

Read/Write

vsDataSwitchPortStp

configuredPathCost

IP Transport

Real

Default

Read/Write

vsDataSwitchPortStp

edgePortBpduGuardTimeOut

IP Transport

Timer

Default

Read/Write

vsDataSwitchPortStp

edgePortBpduGuardTimeOut

IP Transport

Timer

Default

Read/Write

vsDataSwitchPortStp

edgePortMode

IP Transport

EnumRef

Default

Read/Write

vsDataSwitchPortStp

edgePortMode

IP Transport

EnumRef

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpActive

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpActive

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpBpduReceive

IP

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

477 (520)

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpBpduReceive

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpPortPriority

IP

Real

TND

5/1553-HSD 101 02

Read/Write

vsDataSwitchPortStp

l2gpPortPriority

IP

Real

Read

vsDataSwitchPortStp

l2gpPseudoRootId

IP

Id

Read

vsDataSwitchPortStp

l2gpPseudoRootId

IP

Real

Default

Read/Write

vsDataSwitchPortStp

manualPathCost

IP Transport

Real

Default

Read/Write

vsDataSwitchPortStp

manualPathCost

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSwitchPortStp

priority

IP Transport

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSwitchPortStp

priority

IP Transport

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

478 (520)

Read

vsDataSwitchPortStp

protocolVersion

IP Transport

EnumRef

Read

vsDataSwitchPortStp

protocolVersion

IP Transport

EnumRef

Read

vsDataSwitchPortStp

remoteBridgeId

IP Transport

Id

Read

vsDataSwitchPortStp

remoteBridgeId

IP Transport

Real

Read

vsDataSwitchPortStp

rootPathCost

IP Transport

Real

Read

vsDataSwitchPortStp

rootPathCost

IP Transport

Real

Read
Read
Read

N
N
N

Y
Y
Y

Y
Y
Y

N
N
N

vsDataSwitchPortStp
vsDataSwitchPortStp
vsDataSwitchPortStp

settingsUsed
settingsUsed
stpRole

IP Transport
IP Transport
IP Transport

Real
Real
EnumRef

Read

vsDataSwitchPortStp

stpRole

IP Transport

EnumRef

Read

vsDataSwitchPortStp

stpState

IP Transport

State

Read

vsDataSwitchPortStp

stpState

IP Transport

State

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

479 (520)

Restricted

vsDataSwitchPortStp

id

TN Administration

Id

Restricted

vsDataSwitchPortStp

id

TN Administration

Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataSwitchPortStp
vsDataSwitchPortStp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataSwitchStp

administrativeState

TN Administration

EnumRef

Read/Write

vsDataSwitchStp

administrativeState

TN Administration

EnumRef

Default

Read/Write

vsDataSwitchStp

bridgeForwardDelay

IP Transport

Real

Default

Read/Write

vsDataSwitchStp

bridgeForwardDelay

IP Transport

Real

Default

Read/Write

vsDataSwitchStp

bridgeHelloTime

IP Transport

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Default

Prepared: EZIEAGA

Network Parameters

480 (520)

Read/Write

vsDataSwitchStp

bridgeHelloTime

IP Transport

Real

Read

vsDataSwitchStp

bridgeId

IP Transport

Id

Read

vsDataSwitchStp

bridgeId

IP Transport

Real

Read/Write

vsDataSwitchStp

bridgeMaxAge

IP Transport

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Network Parameters

481 (520)

Read/Write

vsDataSwitchStp

bridgeMaxAge

IP Transport

Real

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSwitchStp

bridgePriority

IP Transport

EnumRef

TND

5/1553-HSD 101 02/7

Read/Write

vsDataSwitchStp

bridgePriority

IP Transport

EnumRef

Read/Write

vsDataSwitchStp

mode

IP Transport

EnumRef

Default

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Prepared: EZIEAGA

Network Parameters

482 (520)

Read/Write

vsDataSwitchStp

mode

IP Transport

EnumRef

Read

vsDataSwitchStp

rootBridgeId

IP Transport

Id

Read

vsDataSwitchStp

rootBridgeId

IP Transport

Real

Read
Read

N
N

Y
Y

Y
Y

N
N

vsDataSwitchStp
vsDataSwitchStp

rootPortNumber
rootPortNumber

IP Transport
IP Transport

Real
Real

Read

IP Transport

Real

Read

IP Transport

Real

Read

IP Transport

Real

Read

IP Transport

Real

Read

IP Transport

Real

Read

IP Transport

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

483 (520)

Restricted

vsDataSwitchStp

id

TN Administration

Id

Restricted

vsDataSwitchStp

id

TN Administration

Id

Read

IP Transport

Real

Read

IP Transport

Real

Read/Write

vsDataSwitchStp

transmitHoldCount

IP Transport

Real

Read/Write

vsDataSwitchStp

transmitHoldCount

IP Transport

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataSwitchStp
vsDataSwitchStp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND O&M

Read/Write

vsDataSynchronization

degradationIsFault

Network Sync

EnumRef

TND O&M

Read/Write

vsDataSynchronization

degradationIsFault

Network Sync

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

Read/Write

vsDataSynchronization

featureStatePtpFreq

Read/Write

Read/Write

vsDataSynchronization

featureStatePtpTime

EnumRef

Read/Write

vsDataSynchronization

featureStateSyncEth

EnumRef

Read/Write

vsDataSynchronization

featureStateSyncEth

EnumRef

Read

Read

Prepared: EZIEAGA

EnumRef
EnumRef
EnumRef

EnumRef
vsDataSynchronization

Date: 2014-05-27
Sheet: 14.0.2

licenseStatePtpFreq

Enumref

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

484 (520)

Read

Read

vsDataSynchronization

licenseStatePtpTime

EnumRef
Enumref

Read

vsDataSynchronization

licenseStateSyncEth

EnumRef

Read

vsDataSynchronization

licenseStateSyncEth

Enumref

Read

Network Sync

EnumRef

Read

Network Sync

EnumRef

Read/Write

vsDataSynchronization

sfnInitializationTime

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataSynchronization

id

TN Administration

Id

Restricted

vsDataSynchronization

id

TN Administration

Id

Read

vsDataSynchronization

syncRefActivity

Network Sync

EnumRef

Read

vsDataSynchronization

syncRefActivity

Network Sync

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

485 (520)

Read

vsDataSynchronization

syncReference

Network Sync

MORef

Read

vsDataSynchronization

syncReference

Network Sync

MORef

84/1553-HSD 101 02/6

Read

vsDataSynchronization

syncRefPriority

Network Sync

Real

84/1553-HSD 101 02/6

Read

vsDataSynchronization

syncRefPriority

Network Sync

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

486 (520)

Read

vsDataSynchronization

syncRefStatus

Network Sync

Status

Read

vsDataSynchronization

syncRefStatus

Network Sync

Status

Read/Write

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataSynchronization
vsDataSynchronization

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

Read/Write

Read/Write

Restricted
Read

Y
N

Y
N

N
N

N
N

Status

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

487 (520)

Read

Status

Read

EnumRef

Read

EnumRef

Read
Read
Restricted
Restricted
Read/Write
Read/Write
Read/Write

N
N
Y
Y
N
N
N

Y
Y
Y
Y
Y
Y
Y

N
N
N
N
Y
Y
Y

Y
Y
N
N
N
N
N

vsDataT1PhysPathTerm

administrativeState

TN Administration

MORef
MORef
Id
Id
Label
Label
EnumRef

Read/Write

vsDataT1PhysPathTerm

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataT1PhysPathTerm

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataT1PhysPathTerm

aisReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

TN Administration
TN Administration

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

TND O&M

Read/Write

vsDataT1PhysPathTerm

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

Default

Read/Write

Default

Read/Write

Restricted

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

488 (520)
TN Administration

Status

degDegM

Physical Interface

Real

vsDataT1PhysPathTerm

degDegM

Physical Interface

Real

vsDataT1PhysPathTerm

degDegThr

Physical Interface

Real

vsDataT1PhysPathTerm

degDegThr

Physical Interface

Real

vsDataT1PhysPathTerm

idlePattern

Physical Interface

EnumRef

vsDataT1PhysPathTerm

idlePattern

Physical Interface

EnumRef

vsDataT1PhysPathTerm

lineNo

Physical Interface

Real

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

489 (520)

Restricted

vsDataT1PhysPathTerm

lineNo

Physical Interface

Real

Default

Read/Write

vsDataT1PhysPathTerm

loopback

Physical Interface

EnumRef

Default

Read/Write

vsDataT1PhysPathTerm

loopback

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

vsDataT1PhysPathTerm

rdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataT1PhysPathTerm

rdiReporting

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Read

TN Administration

MORef

Read

TN Administration

MORef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

TND O&M

Read/Write

vsDataT1PhysPathTerm

shutDownTimeout

Physical Interface

Timer

TND O&M

Read/Write

vsDataT1PhysPathTerm

shutDownTimeout

Physical Interface

Timer

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataT1PhysPathTerm
vsDataT1PhysPathTerm

id
id

TN Administration
TN Administration

Id
Id

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

490 (520)

TND

Read/Write

vsDataT1PhysPathTerm

transmissionMode

Physical Interface

EnumRef

TND

Read/Write

vsDataT1PhysPathTerm

transmissionMode

Physical Interface

EnumRef

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataT1PhysPathTerm
vsDataT1PhysPathTerm

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND O&M

Read/Write

vsDataT1Ttp

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataT1Ttp

aisReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

Physical Interface

Real

Prepared: EZIEAGA

vsDataT1Ttp

Date: 2014-05-27
Sheet: 14.0.2

degDegM

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

491 (520)

TND O&M

Read/Write

vsDataT1Ttp

degDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataT1Ttp

degDegThr

Physical Interface

Real

TND O&M

Read/Write

vsDataT1Ttp

degDegThr

Physical Interface

Real

Default

Read/Write

vsDataT1Ttp

idlePattern

Physical Interface

EnumRef

Default

Read/Write

vsDataT1Ttp

idlePattern

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

vsDataT1Ttp

rdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataT1Ttp

rdiReporting

Physical Interface

Real

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

Restricted

TN Administration

Id

Prepared: EZIEAGA

vsDataT1Ttp

Date: 2014-05-27
Sheet: 14.0.2

id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

492 (520)

Restricted

vsDataT1Ttp

id

TN Administration

Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataT1Ttp
vsDataT1Ttp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataT3PhysPathTerm

administrativeState

TN Administration

EnumRef

Read/Write

vsDataT3PhysPathTerm

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataT3PhysPathTerm

aisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataT3PhysPathTerm

aisReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataT3PhysPathTerm
vsDataT3PhysPathTerm

lineNo
lineNo

Physical Interface
Physical Interface

Real
Real

Default

Read/Write

vsDataT3PhysPathTerm

loopback

Physical Interface

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
Default

Read/Write

N/A

Read

N/A

Read

TND O&M

Read/Write

TND O&M

Read/Write

Network Parameters
Physical Interface

EnumRef

TN Administration

EnumRef

TN Administration

EnumRef

vsDataT3PhysPathTerm

rdiReporting

Physical Interface

Real

vsDataT3PhysPathTerm

rdiReporting

Physical Interface

Real

Read

TN Administration

MORef

Read

TN Administration

MORef

Read
Read

N
N

Y
Y

N
N

N
N

TN Administration
TN Administration

MORef
MORef

TND O&M

Read/Write

vsDataT3PhysPathTerm

shutDownTimeout

Physical Interface

Timer

TND O&M

Read/Write

vsDataT3PhysPathTerm

shutDownTimeout

Physical Interface

Timer

TND
TND

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataT3PhysPathTerm
vsDataT3PhysPathTerm

id
id

TN Administration
TN Administration

Id
Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataT3PhysPathTerm
vsDataT3PhysPathTerm

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted
Restricted

Y
Y

N
N

N
N

N
N

Restricted
Restricted
Restricted
Restricted
Read/Write

Y
Y
Y
Y
N

N
N
N
Y
Y

N
N
N
N
Y

N
N
N
N
N

vsDataTimingUnit

hptsiOutEnabled

Prepared: EZIEAGA

vsDataT3PhysPathTerm

Date: 2014-05-27
Sheet: 14.0.2

loopback

493 (520)

Real

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

494 (520)

N/A

124/1553-HSD 101 02/7 Read/Write

vsDataTnlQosClass

prefIubUserPlaneTransportOption

QoS Handling

StructRef

TND

124/1553-HSD 101 02/7 Read/Write

vsDataTnlQosClass

prefIubUserPlaneTransportOption.atm

QoS Handling

EnumRef

TND

124/1553-HSD 101 02/7 Read/Write

vsDataTnlQosClass

prefIubUserPlaneTransportOption.ipv4

QoS Handling

EnumRef

Read/Write

vsDataTrafficManagement

featureState

Read/Write

vsDataTrafficManagement

featureState

Read

vsDataTrafficManagement

licenseState

Read

vsDataTrafficManagement

licenseState

IP Transport

EnumRef

Restricted
Restricted
Read/Write
Read/Write
Read/Write

Y
Y
N
N
N

Y
Y
Y
Y
Y

N
N
Y
Y
Y

N
N
N
N
N

vsDataTrafficManagement
vsDataTrafficManagement
vsDataTrafficManagement
vsDataTrafficManagement
vsDataTrafficManagementQueue

id
id
userLabel
userLabel
dropMechanism

TN Administration
IP Transport
TN Administration
IP Transport
IP Transport

Id
Id
Label
Label
MORef

Read/Write

vsDataTrafficManagementQueue

queueLength

IP Transport

Real

Read
Read
Read/Write

N
N
N

N
N
Y

N
N
Y

N
N
N

vsDataTrafficManagementQueue

queueWeight

IP Transport
IP Transport
IP Transport

Real
Real
Real

Read/Write

vsDataTrafficManagementQueue

redProperties

IP Transport

MORef

TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

EnumRef

IP Transport

EnumRef

EnumRef

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

495 (520)

Read/Write

vsDataTrafficManagementQueue

redProperties.redAveragingWeightFactor

IP Transport

Real

Read/Write

vsDataTrafficManagementQueue

redProperties.redMaxThreshold

IP Transport

Real

Read/Write

vsDataTrafficManagementQueue

redProperties.redMinThreshold

IP Transport

Real

Read
Restricted
Read/Write
Restricted

N
Y
N
N

Y
Y
Y
Y

N
N
Y
Y

Y
N
N
Y

vsDataTrafficManagementQueue
vsDataTrafficManagementQueue
vsDataTrafficScheduler

id
userLabel
dscpMap

IP Transport
TN Administration
TN Administration
IP Transport

MORef
Id
Label
StructRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Prepared: EZIEAGA

Network Parameters

496 (520)

Restricted

vsDataTrafficScheduler

dscpMap.dscp

IP Transport

Real

Restricted

vsDataTrafficScheduler

dscpMap.queue

IP Transport

Real

Read/Write

Read/Write

vsDataTrafficScheduler

egressCbs

IP Transport

Real

Read/Write

Read/Write

vsDataTrafficScheduler

egressCir

IP Transport

Real

Read/Write

vsDataTrafficScheduler

egressCirLow

IP Transport

Real

Read/Write

Read
Restricted

N
Y

Y
Y

N
N

Y
N

IP Transport

MORef

Restricted

TN Administration

Id

vsDataTrafficScheduler

Date: 2014-05-27
Sheet: 14.0.2

id

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

N/A

Prepared: EZIEAGA

Network Parameters

497 (520)

Read/Write

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataTrafficScheduler
vsDataTrafficScheduler

userLabel
wpEndQueue

TN Administration

Label
Real

Read/Write

vsDataTrafficScheduler

wpStartQueue

IP Transport

Label

Restricted

Restricted

vsDataTransportNetwork

id

TN Administration

Id

Restricted

vsDataTransportNetwork

id

TN Administration

Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataTransportNetwork
vsDataTransportNetwork

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Read/Write

vsDataTuSyncRef

administrativeState

TN Administration

EnumRef

Read/Write

vsDataTuSyncRef

administrativeState

TN Administration

EnumRef

Read

TN Administration

Status

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

498 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataTuSyncRef
vsDataTuSyncRef

id
id

TN Administration
TN Administration

Id
Id

Read/Write
Read/Write
Read

N
N
N

Y
Y
Y

Y
Y
N

N
N
N

vsDataTuSyncRef
vsDataTuSyncRef
vsDataTwampResponder

userLabel
userLabel
actualModes

TN Administration
TN Administration

Label
Label
Real

Read

vsDataTwampResponder

actualModes

Real

Read/Write

vsDataTwampResponder

administrativeState

EnumRef

Read/Write

vsDataTwampResponder

administrativeState

EnumRef

Read

TND
TND

Prepared: EZIEAGA

Status

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

TND
TND
Default

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Network Parameters

499 (520)

Read

EnumRef

Restricted
Restricted
Read

Y
Y
N

Y
Y
N

Y
Y
N

N
N
N

Read

Restricted
Restricted
Restricted

Y
Y
Y

Y
Y
Y

N
N
N

N
N
N

vsDataTwampResponder
vsDataTwampResponder
vsDataTwampResponder

id
id
udpPort

Id
Real
Real

Restricted

vsDataTwampResponder

udpPort

Real

Read/Write
Read/Write
Restricted
Restricted

N
N
N
N

Y
Y
Y
Y

Y
Y
N
N

N
N
N
N

vsDataTwampResponder
vsDataTwampResponder
vsDataUniSaalProfile
vsDataUniSaalProfile

userLabel
userLabel
profileData
profileData

Signalling Bearer
Signalling Bearer

Label
Label
StructRef
StructRef

Restricted

vsDataUniSaalProfile

profileData.congestionAbatement

Signalling Bearer

Real

vsDataTwampResponder
vsDataTwampResponder

ipAccessHostEtRef
ipAccessHostEtRef

MORef
MORef
EnumRef

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

500 (520)

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.congestionAbatement

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.congestionOnSet

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.congestionOnSet

Signalling Bearer

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.initialCredit

Signalling Bearer

Real

CPI

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.initialCredit

Signalling Bearer

Real

Default

Restricted

vsDataUniSaalProfile

profileData.maxCC

Signalling Bearer

Real

Default

Restricted

vsDataUniSaalProfile

profileData.maxCC

Signalling Bearer

Real

Restricted

vsDataUniSaalProfile

profileData.maxPD

Signalling Bearer

Real

CPI

Prepared: EZIEAGA

1/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

501 (520)

CPI

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.maxPD

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.maxStat

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.maxStat

Signalling Bearer

Real

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerCC

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerCC

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerIdle

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerIdle

Signalling Bearer

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

502 (520)

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerKeepAlive

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerKeepAlive

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerNoResponse

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerNoResponse

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerPoll

Signalling Bearer

Timer

Default

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalProfile

profileData.timerPoll

Signalling Bearer

Timer

Read
Read

N
N

Y
Y

N
N

Y
Y

TN Administration
TN Administration

MORef
MORef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataUniSaalProfile
vsDataUniSaalProfile

id
id

TN Administration
TN Administration

Id
Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataUniSaalProfile
vsDataUniSaalProfile

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND
TND

TND

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalTp

aal5TpVccTpId

Signalling Bearer

Id

TND

1/1553-HSD 101 02/7

Restricted

vsDataUniSaalTp

aal5TpVccTpId

Signalling Bearer

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

503 (520)

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataUniSaalTp

maxSduSize

Signalling Bearer

Real

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataUniSaalTp

maxSduSize

Signalling Bearer

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

MORef
MORef

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataUniSaalTp

uniSaalProfileId

Signalling Bearer

Id

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataUniSaalTp

uniSaalProfileId

Signalling Bearer

MORef

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataUniSaalTp
vsDataUniSaalTp

id
id

TN Administration
TN Administration

Id
Id

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataUniSaalTp
vsDataUniSaalTp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND
TND

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

504 (520)

Read

EnumRef

Read

EnumRef

Read/Write

TN Administration

EnumRef

Read/Write

TN Administration

EnumRef

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Default

Read/Write

Physical Interface

EnumRef

Default

Read/Write

Physical Interface

EnumRef

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

Physical Interface

Timer

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

505 (520)

TND O&M

Read/Write

Physical Interface

Timer

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

Label
Label

Restricted

TN Administration

Id

Restricted

TN Administration

Id

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

Read/Write

vsDataVc12Ttp

administrativeState

TN Administration

EnumRef

Read/Write

vsDataVc12Ttp

administrativeState

TN Administration

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

506 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

vsDataVc12Ttp

expectedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

expectedPathTrace

Physical Interface

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

Physical Interface

Timer

Prepared: EZIEAGA

vsDataVc12Ttp

Date: 2014-05-27
Sheet: 14.0.2

shutDownTimeout

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

507 (520)

TND O&M

Read/Write

vsDataVc12Ttp

shutDownTimeout

Physical Interface

Timer

TND O&M

Read/Write

vsDataVc12Ttp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

timConsequentAction

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

transmittedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

transmittedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

tuAisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

tuAisReporting

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataVc12Ttp
vsDataVc12Ttp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted

vsDataVc12Ttp

id

TN Administration

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

508 (520)

Restricted

vsDataVc12Ttp

id

TN Administration

Id

TND O&M

Read/Write

vsDataVc12Ttp

vcDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

vcDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

vcDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

vcDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

vcRdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVc12Ttp

vcRdiReporting

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

509 (520)

N/A

Read

TN Administration

Status

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

Physical Interface

EnumRef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

510 (520)

TND O&M

Read/Write

Physical Interface

EnumRef

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

Label
Label

Restricted

TN Administration

Id

Restricted

TN Administration

Id

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

511 (520)

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

auAisReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

auAisReporting

Physical Interface

Real

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

512 (520)

TND O&M

Read/Write

vsDataVc4Ttp

expectedPathTrace

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

expectedPathTrace

Physical Interface

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

Physical Interface

EnumRef

Prepared: EZIEAGA

vsDataVc4Ttp

Date: 2014-05-27
Sheet: 14.0.2

pathTraceFormat

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND O&M

Network Parameters

Read/Write

Read
Read

N
N

Y
Y

N
N

N
N

TND O&M

Read/Write

vsDataVc4Ttp

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

Read/Write

Prepared: EZIEAGA

vsDataVc4Ttp

Physical Interface

EnumRef

TN Administration
TN Administration

MORef
MORef

timConsequentAction

Physical Interface

Real

vsDataVc4Ttp

timConsequentAction

Physical Interface

Real

vsDataVc4Ttp

transmittedPathTrace

Physical Interface

Real

vsDataVc4Ttp

transmittedPathTrace

Physical Interface

Real

vsDataVc4Ttp

userLabel

TN Administration

Label

Date: 2014-05-27
Sheet: 14.0.2

pathTraceFormat

513 (520)

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

514 (520)

Read/Write

vsDataVc4Ttp

userLabel

TN Administration

Label

Restricted

vsDataVc4Ttp

id

TN Administration

Id

Restricted

vsDataVc4Ttp

id

TN Administration

Id

TND O&M

Read/Write

vsDataVc4Ttp

vcDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

vcDegM

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

vcDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

vcDegThreshold

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

vcRdiReporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVc4Ttp

vcRdiReporting

Physical Interface

Real

TND

1/1553-HSD 101 02/7

Read/Write

vsDataVclTp

atmTrafficDescriptorId

ATM Connection

Id

TND

1/1553-HSD 101 02/7

Read/Write

vsDataVclTp

atmTrafficDescriptorId

ATM Connection

MORef

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

515 (520)

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

TND O&M

Read/Write

vsDataVclTp

counterActivation

TN PM Counters

Real

TND O&M

Read/Write

vsDataVclTp

counterActivation

O&M PM Statistics

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataVclTp

externalVci

ATM Connection

Real

TND

1/1553-HSD 101 02/7

Restricted

vsDataVclTp

externalVci

ATM Connection

Real

N/A

Read

TN Administration

EnumRef

N/A

Read

TN Administration

EnumRef

Read
Read

N
N

Y
Y

Y
Y

N
N

TN Administration
TN Administration

MORef
MORef

Read/Write

TN Administration

Label

Prepared: EZIEAGA

vsDataVclTp

Date: 2014-05-27
Sheet: 14.0.2

userLabel

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

516 (520)

Read/Write

vsDataVclTp

userLabel

TN Administration

Label

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataVclTp
vsDataVclTp

id
id

TN Administration
TN Administration

Id
Id

Read

TN Administration

MORef

Read/Write

vsDataVlan

userLabel

TN Administration

Label

Read/Write

vsDataVlan

vid

IP Transport

Real

Restricted

vsDataVlan

id

TN Administration

Id

Restricted

vsDataVlan

vlanType

IP Transport

EnumRef

Restricted
Read/Write
Read/Write

N
N
Y

Y
Y
Y

Y
Y
Y

N
N
N

TND O&M

Restricted
Read/Write

Y
N

Y
Y

N
Y

N
N

vsDataVpcTp

alarmReport

ATM Connection

EnumRef

TND O&M

Read/Write

vsDataVpcTp

alarmReport

ATM Connection

EnumRef

N/A

Read

TN Administration

Status

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

N/A

TND

TND

Prepared: EZIEAGA

5/1553-HSD 101 02/7

5/1553-HSD 101 02/7

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

N/A

Read

TND O&M

Read/Write

vsDataVpcTp

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

TND O&M

Read/Write

Prepared: EZIEAGA

517 (520)
TN Administration

Status

continuityCheck

ATM Connection

Real

vsDataVpcTp

continuityCheck

ATM Connection

Real

vsDataVpcTp

counterMode

ATM Connection

EnumRef

vsDataVpcTp

counterMode

O&M PM Statistics

EnumRef

vsDataVpcTp

nomPmBlkSize

ATM Connection

EnumRef

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

TND O&M

Read/Write

vsDataVpcTp

N/A

Read

N/A

Read

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataVpcTp
vsDataVpcTp

nomPmBlkSize

518 (520)
ATM Connection

EnumRef

TN Administration

EnumRef

TN Administration

EnumRef

userLabel
userLabel

TN Administration
TN Administration

Label
Label

TND
TND

1/1553-HSD 101 02/7


1/1553-HSD 101 02/7

Restricted
Restricted

Y
Y

Y
Y

N
N

N
N

vsDataVpcTp
vsDataVpcTp

id
id

TN Administration
TN Administration

Id
Id

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataVplTp

atmTrafficDescriptor

ATM Connection

MORef

CPI

1/1553-HSD 101 02/7

Read/Write

vsDataVplTp

atmTrafficDescriptor

ATM Connection

MORef

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

Restricted

ATM Connection

Real

TND

Prepared: EZIEAGA

1/1553-HSD 101 02/7

vsDataVplTp

Date: 2014-05-27
Sheet: 14.0.2

externalVpi

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport
TND

Restricted

N/A

Read

N/A

Read

Read/Write
Read/Write

N
N

Restricted
Restricted

Real

TN Administration

EnumRef

TN Administration

EnumRef

Y
Y

Y
Y

N
N

vsDataVplTp
vsDataVplTp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Y
Y

Y
Y

N
N

N
N

vsDataVplTp
vsDataVplTp

id
id

TN Administration

Id
Id

Read/Write

vsDataVt15Ttp

administrativeState

TN Administration

EnumRef

Read/Write

vsDataVt15Ttp

administrativeState

TN Administration

EnumRef

TND O&M

Read/Write

vsDataVt15Ttp

aisVreporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVt15Ttp

aisVreporting

Physical Interface

Real

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

Status

N/A

Read

TN Administration

EnumRef

Prepared: EZIEAGA

vsDataVplTp

Date: 2014-05-27
Sheet: 14.0.2

externalVpi

519 (520)
ATM Connection

TND

1/1553-HSD 101 02/7

Network Parameters

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

USER DESCRIPTION_x000D_Transport

Network Parameters

520 (520)

N/A

Read

TN Administration

EnumRef

TND O&M

Read/Write

vsDataVt15Ttp

rdiVreporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVt15Ttp

rdiVreporting

Physical Interface

Real

TND O&M

Read/Write

vsDataVt15Ttp

shutDownTimer

Physical Interface

Timer

TND O&M

Read/Write

vsDataVt15Ttp

shutDownTimer

Physical Interface

Timer

Read/Write
Read/Write

N
N

Y
Y

Y
Y

N
N

vsDataVt15Ttp
vsDataVt15Ttp

userLabel
userLabel

TN Administration
TN Administration

Label
Label

Restricted

vsDataVt15Ttp

id

TN Administration

Id

Restricted

vsDataVt15Ttp

id

TN Administration

Id

Prepared: EZIEAGA

Date: 2014-05-27
Sheet: 14.0.2

No: 87/1553-HSD 101 02 Uen_x000D_Rev: M3

You might also like