Professional Documents
Culture Documents
Correct
Q.1) Which of the following is NOT a basic component to a plumbing system?
A. The drainage and vent system
B. Water service pipe and distributing pipes
C. Pollution Control (Your Answer)
D. Plumbing fixtures
Correct
Q.2) What do you call the installation of all pipes in the plumbing system that is in
partitions and under floors?>
A. Tempering
B. Roughing-in (Your Answer)
C. Concealed plumbing
D. Fixturing
Correct
Q.3) What will be the basis in the design of waer piping sytem in localities where the
water pressure is fluctuating all throughout the day?
A. Time of the day when the maximum pressure is available
B. Number of households in the area using water
C. Minimum pressure available (Your Answer)
D. Maximum pressure available
Correct
Q.4) What do you call a hemp or old hemp rope soaked in oil or tar to make it
waterproof?
A. Sisal
B. Manila
C. Abaca
D. Oakum (Your Answer)
Wrong
Q.5) Through what means must waste of food handling equipment discharge?
A. Vertical gap
B. Grease interceptor (Your Answer)
C. Indirect Waste pipe (Correct Answer)
D. Direct connection
Correct
Q.6) What is a group vent pipe?
A. Circuit vent (Your Answer)
B. Drain
C. Continuous vent
D. Cross connection
Correct
Q.7) When was NAMPAP registered with the Securities and Exchage Commission?
A. 1925
B. 1942
C. 1937
D. 1935 (Your Answer)
Wrong
Q.8) A horizntal drain that is sized to provide free movement of air above the flow
line of the drain is called a ___
A. continuous waste system (Your Answer)
B. durham waste and vent system
C. combination waste and vent system (Correct Answer)
D. solvent waste and vent system
Correct
Q.9) What should be made of connections between a potable water supply and an
automatic fire sprinkling machine?
A. With vacuum breaker
B. With relief valves
C. With check valve (Your Answer)
D. With valve regulator
Correct
Q.10) What type of concealed connections on fixtures shall be provided with access
panel or utility at least 0.3m in its least dimension for easy inspection and
repair?
A. Hubless
B. Flanged
C. Slip joint (Your Answer)
D. Ball and socket
Wrong
Q.11) Fixture connections that require the removal of an access panel for servicing are
considered ____.
A. accessible (Correct Answer)
B. readily accessible (Your Answer)
C. not accessible
D. exposed
Correct
Q.12) What is the minimum elapsed time required that the pressurized water be kept
in the pipe system for the water test?
A. 15 min (Your Answer)
B. 10 min
C. 30 min
D. 1 hour
Correct
Q.13) What is that portion of rainfall or other precipitation which runs off over the
surface of the ground called?
A. Surface water (Your Answer)
B. Rain water
C. Run-off water
D. Ground water
Correct
Q.14) How many pipes that discharge into a drainage system but which are not
connected directly to the drainage system clasiffied?
A. Complex wastes
B. Indirect wastes (Your Answer)
C. Special wastes
D. Direct wastes
Wrong
Q.15) Which of the following types of work required a plumbing permit?
A. The replacement of a faulty gate valve
B. The relpacement of an electric water heater (Correct Answer)
C. The clearance of the drain stoppage (Your Answer)
D. The replacement of the faucet stem
Wrong
Q.16) What is a liquid waste that contains animal or vegetable matter in suspension or
solution?
A. Sewer
B. Sewage (Correct Answer)
C. Domestic waste (Your Answer)
D. Culinary waste
Correct
Q.17) What tank is integral with water closet, urinal, or similar fixtures for flushing or
removing excrements in the fixture?
A. Flush (Your Answer)
B. Septic
C. Drain
D. Cistern
Wrong
Q.18) What must the interceptors used in bottling establishment be capable of
seperating from the other solids before discharging he waste into the drainage
system?
A. Oil (Your Answer)
B. Flammable materials
C. Bottled fluids
D. Broken glass or other solids (Correct Answer)
Wrong
Q.19) What must be fitted on a fixture that is equipped with threads for a garden
hose?
A. Check valve
B. Backflow preventer
C. Air gap (Your Answer)
D. Vacuum breaker (Correct Answer)
Correct
Q.20) What do you call the downward fall of a pipe?
A. Grade (Your Answer)
B. Inclined
C. Slope
D. Slant
Wrong
Q.21) What are intended to be protected by vents?
A. Fixture outlets (Your Answer)
B. Drains
C. Traps
D. Trap seals (Correct Answer)
Correct
Q.22) Which of the following also serves as drains?
A. Relief vents
B. Common vents
C. Wet vents (Your Answer)
D. Dry vents
Wrong
Q.23) What tube is made of plastic material and colored black whose cross-sectional
shape is normally oval and is denoted by its outside diameter and is normally
Correct
Q.29) What pipe conveys potable water from a building supply to a plumbing fixture?
A. Water Distribution (Your Answer)
B. Water riser
C. Water line
D. Water stack
Correct
Q.30) What do you call the pipe or tubing that connects the oultlet of a plumbing
fixture to the trap?
A. Outflow
B. Tailpiece (Your Answer)
C. Head Tubing
D. Connector
Correct
Q.31) What do you call a combination of elbows or bends which brings one section of
pipe out of line but into a line parallel with the other section of the pipe?
A. Offset (Your Answer)
B. Crown vent
C. Drainage turn
D. Picth
Wrong
Q.32) What is the standard working pressure for a water heater?
A. 140 psi
B. 125 psi (Correct Answer)
C. 100 psi
D. 75 psi (Your Answer)
Correct
Q.33) What do you call a water supply pipe connecting the fixtures with the fixture
branch?
A. Corporation
B. Service
C. Fixture supply (Your Answer)
D. Special
Wrong
Q.34) What delivers water under pressure?
A. Ejector
B. Sump pump
C. Pressure controller (Your Answer)
A. 2
B. 4 (Your Answer)
C. 5
D. 3 (Correct Answer)
Wrong
Q.46) How many threads per inch has a cleanout having a size of 76 mm had?
A. 8 (Correct Answer)
B. 10
C. 5
D. 6 (Your Answer)
Wrong
Q.47) How do you call an auxillary vent which provides additional circulation of air in
or between a drainage system classified?
A. Common vent
B. Relief vent (Correct Answer)
C. Island vent
D. Branch vent (Your Answer)
Wrong
Q.48) what device is present in a water heater that allows the emptying or discharge of
excessive pressure
A. Thermostat
B. Relief valve (Correct Answer)
C. Aquastat (Your Answer)
D. Boiler blowoff
Correct
Q.49) Valve up to and including 51 mm in size should be made of what materials?
A. Galvanized iron
B. Cast iron
C. Brass (Your Answer)
D. Copper
Wrong
Q.50) What type of valve in a water system combines to protect agaainst excessive
temperature and pressure build-ups?
A. Temperature and pressure relief valve (Correct Answer)
B. Stop valve
C. Tempering valve
D. Temperature relief valve (Your Answer)
Correct
Q.51) Grease interceptors must be equipped with devices to control the rate of which
of the following?
A. Heat Transference
B. Air flow
C. Waste flow
D. Water flow (Your Answer)
Wrong
Q.52) What is the ideal inside diameter of cesspools?
A. 10 ft
B. 3 meters
C. Not more than 5 meters (Your Answer)
D. Not more than 6 ft (Correct Answer)
Wrong
Q.53) For a discharge capacity in the excreta drainage system of 1.0 to 1.89 per
second, what is its assigned equivalent fixture unit when there is an intermittent
flow in the system?
A. 3
B. 2
C. 4 (Correct Answer)
D. 6 (Your Answer)
Correct
Q.54) What type of valve that will be used for all the outlets in a stand pipe
A. Ball
B. Check
C. Gate (Your Answer)
D. Globe
Wrong
Q.55) The trap of a kitchen sink may NOT accept the waste of which of the following?
A. Clothes wahser (Correct Answer)
B. Garbage disposer
C. Diswasher (Your Answer)
D. Continuous waste
Correct
Q.56) what sewage includes the wastes from metal and chemical plants, oil refineries,
laudries. diary plants and breweries?
A. Residential
B. Commercial
C. Industrial (Your Answer)
D. Institutional
Correct
Q.57) What part of the trap of trapped fixture being served, must individual vents be
connected?
A. Fixture drain (Your Answer)
B. Top
C. Bottom
D. Fixture branch
Correct
Q.58) From where can liquid waste be disposed off directly into the ground?
A. chemical laboratory
B. church sacaruim (Your Answer)
C. toilet
D. restaurant sink
Wrong
Q.59) How many equvalent water supply fixture unit has the flush tank type of water
closet that is for private use?
A. 4
B. 2
C. 3 (Correct Answer)
D. 5 (Your Answer)
Wrong
Q.60) What feature in water supply is NOT advisable to plumbing fixtures, devices
and opportunities?
A. Bacterial quality (Correct Answer)
B. Adequate pressure
C. Sufficient volume
D. Without undue noise (Your Answer)
Wrong
Q.61) What is the least diameter (in mm) of building water service pipe that is allowed
by the plumbing Code?
A. 19 (Correct Answer)
B. 12.5 (Your Answer)
C. 10
D. 25
Correct
Q.62) What type of surface must plumbing fixtures should NOT have?
Correct
Q.86) What is represented by a solid line broken with two dots or dashes in piping
diagrams?
A. Drainage pipe
B. Vent pipe
C. Cold water
D. How water (Your Answer)
Correct
Q.87) The length along the centerline of the pipe and fittings is the ___
A. diagonal length
B. diameter length
C. circumferential length
D. developed length (Your Answer)
Correct
Q.88) What do you call a pipe with a adjacent reverse bends and shaped like the letter
"S"?
A. Double bend (Your Answer)
B. Double hub
C. Increaser
D. Sanitary cross
Correct
Q.89) What type of water closet is installed in such a way that it does not touch the
floor?
A. Hanger
B. Wall-hung (Your Answer)
C. Carrier
D. Handy
Correct
Q.90) If ever it is impractical to install the horizontal drainage piping following the
required minimum slope due to some reasonable constraints, what is the least
required slope that is allowed?
A. 0.5%
B. 1.5%
C. 2.0%
D. 1.0% (Your Answer)
Correct
Q.91) What does NAMPAP mean
A. National Master Plumbing Association of the Philippines
Q.97) Which of the following is an impairment of the quality of potable water which
creates a hazard to public health through poisoning or the spread of disease?
A. Imbalance
B. Risk dange
C. Backflow
D. Contamination r (Your Answer)
Correct
Q.98) What do you call a receptacle installed to collect and drain store water from an
open area?
A. Combination Sewer
B. Split drain
C. Area drain (Your Answer)
D. Floor drain
Correct
Q.99) What do you call the vertical distance between the crown weir and the top of the
dip of a trap?
A. Airbreak
B. Airgap
C. Trap seal (Your Answer)
D. Critical level
Correct
Q.100) A device integrated within an air accumulator vessel that is desgned to
discharge a predetermined quantity of water to fixtures for flushing purposes
is a(an) ___A. expansion tank
B. surge tank
C. flushometer tank (Your Answer)
D. day tank
Correct
Q.101) Which is NOT a plastic pipe?
A. Polybutylene
B. Polyvinyl chloride
C. Polyethylene
D. Black steel (Your Answer)
Correct
Q.102) A vertical vent that is a continuation of the drain to which it connects is a ___
A. circuit vent
B. relief vent
C. continuous vent (Your Answer)
D. branch vent
Correct
Q.103) That part of the lowest piping of a drainage system that recieves the discharge
from soil, waste, and other drainage pipes inside the walls of the building and
conveys it to a point 2 ft. outside the building wall is a ___
A. building drain (Your Answer)
B. building sewer
C. waste pipe
D. soil stack
Correct
Q.104) If there are five or more branch intervals located above a horizontal offset of a
drainage stack, what must be made of the offsets?
A. No more than 22 1/2 degrees
B. Eliminated
C. No more than 22 1/2 degrees
D. Vented (Your Answer)
Unanswered
Q.105) When plastic pipe is joined with cast-iron pipe, which of the following types of
joints is acceptable?
A. Caulked
B. Solvent weld
C. Threaded
D. Mechanical (Correct Answer)
Correct
Q.106)
Which of the following does NOT belong to sump pump system?
A. Sump pit
B. Sump pump
C. Discharge piping
D. Hinged covers (Your Answer)
Correct
Q.107) What is the allowable distance between the trap arm and the vent if the fixture
has a trap arm diameter of 32mm?
A. 1.52m
B. 0.76 m (Your Answer)
C. 0.51m
D. 1.07m