Professional Documents
Culture Documents
Program key
48x24
Eject gap
Minus key
Plus key
S2
S1
COM
2-wire
PTE
(-99.9 up to +600.0C)
4.206.7782B
3+2-wire
PTE
(-99.9 up to +600.0C)
4.306.7782B
PT100 2-L
sense
+
24V
(galv. insulated)
force
PT100 3-L
8
-
9
+
24 VDC
(galv. insulated)
Options
z LED green
z Protection IP54 (standard: plug in terminal)
z Analog output 0-10 VDC - (12 bit)
z Analog output 0-20 mA/load 500
z Analog output 4-20 mA/load 500
With analog output setpoints S1 and S2 are not available!
z Setpoint as open emitter
z Dimension strip selectable (8 characters max.)
z 4-wire on demand
Technical data
Dimensions
Input
Output
Housing
Assembly cut out
Fastening
Housing material
Protective system
Weight
Connection
PT100
Measuring range
Resolution
Linearization
Sensor current
Open collector
Analogue output
Accuracy
Indication
Resolution
Measuring fault
Temp. drift
Measuring principle
Supply voltage
Power consumption
Display
Ambient
conditions
Overflow
Indication time
Working temperature
Store temperature
Power unit
Housing:
77 mm
48 mm
42 mm
21 mm
24 mm
91 mm
(with plug in terminal 101 mm)
86 mm
CE-sign
For unlimited use of the instrument within the directives for electromagnetic compatibility 89/336/EC measuring
wires have to be used with shielded cable and cable's shield connected to earth ground at one end only.
GND
S2
S1
COM
PT100 2-L
sense
+
24V
(galv. insulated)
force
PT100 3-L
9
+
24 VDC
(galv. insulated)
Setting
1.
2.
3.
4.
5.
6.
7.
Setpoint
Setpoint
on
on
cutoff
offA
conducting
hysteresis
cutoff
conducting
display
off
display
hysteresis
Program table 1
Program
Number (PN)
2
3
4
5
6
Function
Remark
Display
Temperature is displayed
Celsius=0 / Fahrenheit=1
Display time = measuring time
Method of measurement integrating
Option
Option
0 to +/-20.0
0/1
0.2 to 10.0 seconds
Basic parameters
after reset
0.0
0
1.0
-999 to +9999
-999 to +9999
500.0
0.0
Program table 2
(Setting points)
S1
PN
61
62
63
S2
PN
66
67
68
Function
Display
Setpoint
Hysteresis
Quiescent current
Operating current
-999 to +9999
0 to +9999
0
1
100.0/150.0
0.1/0.1
1/1
Analog output:
(no setpoints)
PT100
2-wire
0.0 up to 600.0C
2.0 seconds
S1 ==>
60.0 and quiescent currrent
open collector conducting = 58.0 ==>hysteresis 2.0
S2 ==>
150.0 and operating current
open collector cut off = 80.0 ==>hysteresis 70.0
0 V output ==> display 0.0
==>
0.0C
10 V output ==> display 600.0
==>
600.0C
Program-key P
MINUS-key W
PLUS-key V
The basic adjustments concerning to the following program example are the ground parameters after a total reset occuring through a power on with
pressing P-key (see previous page).
Program advices:
Pressing the P-key enters always the program mode with program number 2. The P2 begins to blink in change with the current value after 3
seconds. After further 4 seconds the system leaves the program mode and goes to the standard mode. In program mode pressing W or V -key
selects the current values which are free scalable with both the keys. All the other parameters will be memorized automatically after leaving program
mode.
Programming
To program number 2 with P.
Standard mode
Programming finished.
All programmed values are memorized
after 7 seconds. Jumps back into
standard mode automatically.