You are on page 1of 118

Gear Catalog

Download the most up-to-date


version at www.rexnord.com

Falk A-Plus Parallel


& Right-Angle Shaft Drives
(Inch)

Falk A-Plus Parallel


& Right-Angle Shaft Drives

To learn more about the Falk A-Plus Parallel & Right-Angle Shaft Drives,
go to www.rexnord.com, where youll find:
Product information Brochures Catalogs Manuals
866-REXNORD/866-739-6673 (toll-free within the U.S.) or 414-643-2366 (Outside the U.S.)

Table Of Contents
Description

Page

General Information
Falk A-Plus Parallel & Right-Angle Shaft Drives Basic Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Conditions Affecting Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7
How to Select an A-Plus Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9, 10
Accessory & Option Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 12, 13
Gear Drive Nomenclature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
How to Order an A-Plus Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Type A Drive Selection
Shaft Assemblies & Rotations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Horsepower & Torque Ratings/Single Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 20
Horsepower & Torque Ratings/Double Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 24
Horsepower & Torque Ratings/Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 - 28
Horsepower & Torque Ratings/Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 32
Type A Technical Data and Dimensions
Basic Thermal Horsepower Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 - 38
Overhung Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 - 45
Low-Speed Shaft Thrust Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Exact Ratios/Parallel Shaft Gear Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47, 48
Type A Single Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Type A Double Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Type A Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Type A Quadruple Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Type AR Double Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53, 54
Type AR Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55, 56
Type AR Quadruple Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57, 58
Type ARJ Double, Triple & Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Type AXV & AXVQ Double Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60, 61
Type AXV & AXVQ Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62, 63
Type AXV & AXVQ Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64, 65
Type AB Drive Selection
Shaft Assemblies & Rotations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Horsepower & Torque Ratings/Double Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67, 68
Horsepower & Torque Ratings/Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 - 72
Horsepower & Torque Ratings/Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 - 76
Type AB Technical Data and DimeNsions
Basic Thermal Horsepower Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77, 78, 79
Overhung Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 - 83
Exact Ratios/Right-Angle Shaft Gear Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Type AB Double Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Type AB Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Type AB Quadruple Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Type ABR Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88, 89
Type ABR Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90, 91
Type ABRJ Triple and Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Type ABX & ABXQ Triple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93, 94
Type ABX & ABXQ Quadruple Reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95, 96
Accessories and Additonal Information
Availability & Compatibility of Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97, 98
Shaft-Driven Fan Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99, 100, 101
Electric Fan Clearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102, 103, 104
Cooling Tube Clearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 - 108
600 Series Shaft Mount Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Alternate Pump Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Torque Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Hollow Low-Speed Shaft Shrink Disc Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Hollow Low-Speed Shaft with Keeper Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Type MCF Couplings Flange Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114, 115
Conversion Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Rexnord 2014

(131-110) 3

General Information
Falk A-Plus Parallel & Right-Angle Shaft Drives Basic Information
Safety Notes
Falk Gear Drives The Falk and Rexnord name on the gear drive is the purchasers
assurance that the drive was engineered, rated and manufactured to sound design
practices.
The power supplied to the geared drive must be equal to or less than the power for
which the drive was selected using the appropriate service factor for the application. The
customer must assume the responsibility of isolating the geared drive from any vibratory
or transient load induced by the driven equipment.
Install and operate Rexnord products in conformance with applicable local and national
safety codes and per Rexnord installation manuals which are shipped with gear drives
and are also available upon request. Suitable guards for rotating members may be
purchased from Rexnord as optional accessories. Consult your local Rexnord district
office for complete details.
People Conveying Equipment Selection of Rexnord gear drives for applications
whose primary purpose is the transportation of people is not approved. This includes
such applications as freight or passenger elevators, escalators, man-lift platforms and ski
tows and ski lifts.
If the primary purpose of the application is material conveyance and occasionally people
are transported, the Rexnord warranty may remain in effect, provided the design load
conditions are not exceeded and certification to the appropriate safety codes and load
conditions has been obtained by the system designer or end user from the appropriate
enforcement authorities.

Gear Drive Ratings


All gear drive ratings in this catalog allow 100% overload for starting loads and
momentary overloads for electric-motor-driven applications operating 10 hours per
day under uniform conditions (unity Service Factor). For other conditions, compute an
equivalent power by multiplying the actual power required for the application by the
appropriate Service Factor.

4 (131-110)

Power and Torque Gear drive mechanical power and torque ratings are tabulated in
the catalog to permit selections for specific application requirements. When the required
input speed falls between two tabulated input speeds of a drive with the same number of
gear reductions, interpolate to determine drive rating.
Thermal Ratings must be considered when selecting a gear drive. Refer to page9
for more information.
Stored and Inactive Drives Each gear drive is spin-tested with a rust-preventive
oil that will protect parts against rust for a period of four months in an outdoor shelter or
12 months in a dry building after shipment from the Factory.
Periodically inspect stored or inactive drives and spray internal parts with rust inhibitor
every six months or more often, if necessary. Drain oil before adding rust inhibitor.
Indoor dry storage is recommended.
Drives ordered for extended storage can be treated at the Factory with a special
preservative and sealed to rust-proof parts for periods longer than those cited above, if
specified on the order.
Refer to appropriate service manual for extended storage of gear drives which have been
in service.
Drawing Symbols The following symbols are used throughout the dimensioned
drawings.
= OIL DIPSTICK
= BREATHER
= OIL FILL
= OIL DRAIN

Factory Warranty Falk products generally carry a limited, one-year warranty


against defects in materials or workmanship; but for an actual statement of the Factory
Warranty, ask your local Rexnord representative or Rexnord distributor for our Standard
Conditions of Sale.

Rexnord 2014

Conditions Affecting Selection


Non-Standard Application Procedures
The following conditions may affect the gear drive selection procedure, drive size and
auxiliary equipment being furnished.
Excessive Overloads The maximum momentary or starting load must not exceed
200% of rated load (100% overload). Rated load is defined as gear drive rating with a
Service Factor of 1.0. If the maximum starting or momentary load exceeds the above
conditions, compute a second equivalent horsepower by dividing the peak load by two.
The gear drive selected must have capacity equal to, or in excess of, the larger equivalent
horsepower.
Reversing Service Applications involving either more than 20 reversals per 10
hour period, or less than 20 reversals per 10 hour period with peak torques greater than
200% of normal load must be referred to the Factory.
Brake-Equipped Applications When a gear drive is equipped with a working
brake that is used to decelerate the motion of the system and the brake is located between
the prime mover and the gear drive, select the drive based on the brake rating or the
highest equivalent input power, whichever is greater. If the brake is used for holding only
and is applied after the motion of the system has come to rest, the brake rating must be
less than 200% of the catalog rating of the gear drive selected for the application. If the
brake rating is greater than 200% of the gear drive catalog rating, refer the application to
the Factory. Also refer to the Factory all applications in which the brake is located on the
output shaft of the gear drive.
Oversize Prime Movers Published Service Factors do not cover applications that
require oversize prime movers for high-energy or peak loads. Refer such applications to
the Factory for selection of suitable drives.
Speed Variation or Multi-Speed Applications The gear drives offered in this
catalog (except Types AXV & ABX) are designed to operate with splash lubrication on any
single-speed application and any ratio shown in the catalog unless otherwise noted. It is
essential that all orders indicate the desired operating speed and ratio so that the proper
internal oil distribution accessories can be supplied for the specific speed. Types AXV
and ABX use a separate motor-driven oil pump to provide lubrication.
These drives are assembled with a variety of standard internal lubrication components
such as oil pans and oil troughs to ensure proper splash lubrication. In addition, different
oil levels are necessary for various drive sizes, speeds and ratios. Consequently, to
operate an existing drive at different speeds from those shown on the nameplate, full
application and nameplate information must be referred to the Factory for review of the
lubrication system.
All variable or multi-speed applications will be referred to the Engineering Department
to specify lubrication components for adequate lubrication at the slowest speed, without
excessive heating or churning at the highest speed. It is essential that all orders indicate
minimum and maximum speeds, as well as the speed duration cycles. A separate motordriven oil pump (at an extra charge) may be required.
When selecting gear drives for multi-speed or variable speed applications, determine the
speed which develops the greatest torque and select the drive on this basis. If the speed
is not listed in the selection table, use the next lower speed.

Application-Adjusted Thermal Rating, page9 The Application-Adjusted


Thermal Rating is the actual power rating without service factor that a gear drive will
transmit continually for three hours or more without overheating. The ApplicationAdjusted Thermal Rating considers the environmental factors of the application which
will affect the ability of the drive to dissipate heat. These factors include ambient
temperature, air velocity, altitude (thin air does not remove heat effectively), inlet water
temperature and duty cycle (percentage of an hour that the drive operates). Factors for
these conditions must be used to modify the Basic Thermal Rating when determining the
Application-Adjusted Thermal Rating.
Checking the thermal rating is extremely important. If a gear drive creates heat faster than
it can be dissipated, severe damage may occur.
If the gear drive operates for three hours or more per day and the run time equals or
exceeds the shutdown time, or if the continuous operating time exceeds three hours,
selection must be made on the basis of adequate thermal rating using the ApplicationAdjusted Thermal Rating. The duty cycle factor considers an increase in the Basic
Thermal Rating for gear drives that operate less than 100% of any one hour time period.
If a drive operates for more than three hours and operates continuously for any given
hour of the day, then the duty cycle must be considered 100%.
Effects of Solar Energy If a drive operates in the sun at ambient temperatures
over 100F (38C), then special measures must be taken to protect the drive from solar
energy. This protection can consist of a canopy over the drive or reflective paint on the
drive. If neither is possible, a heat exchanger or other cooling device may be required.
Overhung Loads and Thrust Loads The overhung load and thrust load ratings
published in this catalog are based on a service factor of unity and a combination of
the most unfavorable conditions of rotation, speed, direction of applied load and drive
loading. If the calculated load exceeds the published value, or if an overhung load and
thrust load are applied simultaneously to a shaft, refer complete application details to
Rexnord. For more information, refer to tables and guidelines on pages39-46 and
pages80-83.
Product Modifications Rexnord can supply special product modifications to
suit your application needs. Contact Rexnord for housing modifications, special ratios,
special shafts, special mounting conditions, accessory modifications and other special
application requirements.
Seal Housing Grease All drives (and backstops if required) will be shipped with
NLGI #2 grease in the seal housing cavities. Where this grease could contaminate a
product, such as in the food and drug industries, clearly indicate on your purchase order
that Gear drive seal housing cavities must not contain grease.
Oil-Pump-Equipped Application When a drive is equipped with an external
motor-driven oil pump, such as an AXV or ABX, and the ambient temperature falls below
50F (10C), or the oil viscosity is in excess of 8000 SSU, an oil heater may be required
to maintain a satisfactory flow rate at start-up to prevent bearing failure. Refer to your
local Rexnord district office.

Rexnord 2014

(131-110) 5

Service Factors
Table 2 Service Factors Listed by Industry

Table 1 Service Factor Conversions


Intermittent - Up to
3 Hours per Day

3 to 10 Hours
per Day

Over 10 Hours
per Day

Multi-Cyl.
Engine

Multi-Cyl.
Engine

Motor

1.00

1.25

1.50

1.00

1.00

1.25

1.50

1.75

1.00

1.25

1.50

1.75

2.00

1.25

1.50

1.75

2.00

2.25

1.50

1.75

2.00

2.25

2.50

1.75

2.00

Table 2 or 3
3 to 10 Hour
Service Factor

Multi-Cyl.
Engine

For applications operating one half hour or less per day and applications driven by
single-cylinder engines, refer to Factory.
These service factors are based on the assumption that the system is free from serious
critical and torsional vibrations and that maximum momentary or starting loads do not
exceed 200% of the normal load.
Occasional and Intermittent Service or Engine-Driven Applications
For multi-cylinder engine-driven applications and all applications operating intermittently
up to 3 hours per day, refer to Table 2 or Table 3 for the Service Factor of the same
application operating 3 to 10 hours per day. Next, in the first column of Table 1, find this
same Service Factor. Then, to the right, under the desired hours service and prime mover,
locate the converted Service Factor.
For example, from Table 3, the Service Factor is 1.25 for a uniformly-loaded belt conveyor.
From Table 1, for the same application the following are the Service Factors for various
conditions.
1. Engine-driven 3 to 10 hours per day; use 1.50 Service Factor.
2. Engine-driven up to 3 hours intermittently; use 1.25 Service Factor.
3. Motor-driven up to 3 hours intermittently; use 1.00 Service Factor.

(For electric motor, steam turbine or hydraulic motor drives recommendations are
MINIMUM and normal conditions are assumed.)
Industry

Service
3 to Over
10 10
Hour Hour

BOTTLING AND BREWING


Bottling Machinery................................... 1.00 1.25
Brew Kettles, Continuous Duty................. 1.25 1.25
Can Filling Machines............................... 1.00 1.25
Cookers Continuous Duty................... 1.25 1.25
Mash Tubs Continuous Duty.............. 1.25 1.25
Scale Hoppers Frequent Starts........... 1.25 1.50
CLAY WORKING INDUSTRY
Brick Press............................................... 1.75 2.00
Briquette Machines.................................. 1.75 2.00
Clay Working Machinery.......................... 1.25 1.50
Pug Mills................................................. 1.25 1.50
DISTILLING........................................... See Brewing
DREDGES
Cable Reels, Conveyors........................... 1.25 1.50
Cutter Head, Jig Drives & Pumps............. 2.00 2.00
Maneuvering Winches.............................. 1.75 2.00
Screen Drives........................................... 1.75 2.00
Stackers, Utility Winches.......................... 1.25 1.50
FOOD INDUSTRY
Beet Slicers.............................................. 1.25 1.50
Bottling, Can Filling Machine................... 1.00 1.25
Cereal Cookers......................................... 1.00 1.25
Dough Mixers, Meat Grinders.................. 1.25 1.50
LUMBER INDUSTRY
Barkers Spindle Feed.......................... 1.25 1.50
Barkers Main Drive............................. 1.75 1.75
Carriage Drive.......................................... Refer to Factory
Conveyors
Burner.............................................. 1.25 1.50
Main or Heavy-Duty......................... 1.50 1.50
Main Log.......................................... 1.75 2.00
Re-Saw Merry-Go-Round................. 1.25 1.50
Slab.................................................. 1.75 2.00
Transfer............................................. 1.25 1.50
Chains Floor....................................... 1.50 1.50
Chains Green...................................... 1.50 1.75
Cut-Off Saws Chain & Drag............... 1.50 1.75
Debarking Drums..................................... 1.75 2.00
Feeds Edger........................................ 1.25 1.50
Feeds Gang......................................... 1.75 1.75
Feeds Trimmer.................................... 1.25 1.50
Log Deck.................................................. 1.75 1.75
Log Hauls Incline, Well Type.............. 1.75 1.75
Log Turning Devices................................ 1.75 1.75
Planer Feed.............................................. 1.25 1.50
Planer Tilting Hoists................................ 1.50 1.50
Rolls Live Off Bearing Roll
Cases..................................................... 1.75 1.75
Sorting Table, Tipple Hoist....................... 1.25 1.50
Transfers Chain & Craneway.............. 1.50 1.75
Tray Drives............................................... 1.25 1.50
Veneer Lathe Drives................................. Refer to Factory
OIL INDUSTRY
Chillers.................................................... 1.25 1.50
Oil Well Pumping..................................... Refer to Factory
Paraffin Filter Press.................................. 1.25 1.50
Rotary Kilns............................................. 1.25 1.50
PAPER MILLS
1.50
Agitator (Mixer)........................................
Agitator for Pure Liquids

1.25
2.00
Barking Drums, Barkers Mech............
1.50
Beater.......................................................
1.25
Breaker Stack...........................................

1.25
Calender .............................................
Chipper....................................................
2.00
1.50
Chip Feeder..............................................
1.25
Coating Rolls...........................................
Conveyors
1.25
Chip, Bark, Chemical........................
2.00
Log (incl. Slab).................................
1.25
Couch Rolls.............................................
2.00
Cutter.......................................................

1.25
Cylinder molds.......................................
Dryers

1.25
Paper Mach. & Conveyor Type........

1.25
Embosser................................................

Industry

Service
3 to Over
10 10
Hour Hour

Extruder..................................................

1.50
Fourdrinier Rolls Lumpbreaker, Wire

Turning Dandy & Return Rolls...............


1.25
Jordan.....................................................

1.50
Kiln Drive................................................

1.50
Mt. Hope & Paper Rolls..........................

1.25
Platter.....................................................

1.50

1.25
Presses (Felt & Suction).........................
Pulper (Continuous)...............................

2.00
Repulper (Heavy Shock)..........................

2.00
Reel (Surface Type).................................

1.25
Screens
Chip & Rotary..................................

1.50
Vibrating..........................................

2.00
Size Press...............................................

1.25

1.25
Super Calenders .................................
Thickener & Washer
AC Motor.........................................

1.50
DC Motor........................................

1.25

1.50
Vacuum Pumps.......................................
Wind & Unwind Stand............................

1.25
Winders (Surface Type)...........................

1.25

Yankee Dryers ...................................


1.25
PLASTIC INDUSTRY
Batch Drop Mill, 2 smooth rolls.............. 1.25 1.25
Calenders................................................ 1.50 1.50
Compounding Mills................................ 1.25 1.25
Continuous Feed, Holding & Blend Mill. 1.25 1.25
Extruders................................................. 1.50 1.50
Variable Speed Drive........................ 1.50 1.50
Fixed Speed Drive............................ 1.75 1.75
Intensive Internal Mixers
Batch Mixers.................................... 1.75 1.75
Continuous Mixers.......................... 1.50 1.50
RUBBER INDUSTRY
Batch Drop Mill, 2 smooth rolls.............. 1.50 1.50
Calenders................................................ 1.50 1.50
Cracker, 2 corrugated rolls...................... 2.00 2.00
Cracker Warmer
2 roll, 1 corrugated roll.......................... 1.75 1.75
Extruders
Continuous Screw Operation........... 1.75 1.75
Intermittent Screw Operation........... 1.75 1.75
Holding, Feed & Blend Mill 2 Roll..... 1.25 1.25
Intensive Internal Mixers
Batch Mixers.................................... 1.75 1.75
Continuous Mixers.......................... 1.50 1.50
Mixing Mill 2 smooth rolls
(if corrugated rolls are used, use
Cracker Warmer service factors)............ 1.50 1.50
Refiner 2 roll...................................... 1.50 1.50
SEWAGE DISPOSAL
Bar Screens............................................. 1.25 1.25
Chemical Feeders.................................... 1.25 1.25
Collectors............................................... 1.25 1.25
Dewatering Screens................................ 1.50 1.50
Scum Breakers........................................ 1.50 1.50
Slow or Rapid Mixers.............................. 1.50 1.50
Thickeners............................................... 1.50 1.50
Vacuum Filters........................................ 1.50 1.50
SUGAR INDUSTRY
Cane Knives, Crushers............................

1.75

1.75
Mills (low-speed end).............................
TEXTILE INDUSTRY
Batchers, Calenders................................ 1.25 1.50
Card Machines........................................ 1.25 1.50
Dry Cans, Dryers.................................... 1.25 1.50
Dyeing Machinery................................... 1.25 1.50
Knitting Machinery.................................. Refer to Factory
Looms, Mangles, Nappers, Pads............. 1.25 1.50
Range Drives........................................... Refer to Factory
Slashers, Soapers, Spinners, Tenter
Frames, Washers, Winders.................... 1.25 1.50
WINDLASS........................................... Refer to Factory

Service Factors for paper mill applications are applied to the nameplate rating of
the electric drive motor at the motor-rated base speed and are consistent with those
shown in TAPPI standards.
Anti-friction bearings only.
A service factor of 1.00 may be applied at base speed of a super calender operating
over a speed range of part constant power and part constant torque, where the
constant power speed range is greater than 1.5 to 1. A service factor of 1.25 is
applicable to super calenders operating at constant torque over the entire speed range
or where the constant power speed range is less than 1.5 to 1.

6 (131-110)

Rexnord 2014

Service Factors
Table 3 Service Factors Listed by Application
(For electric motor, steam turbine or hydraulic motor drives ... recommendations are MINIMUM and normal conditions are assumed.)
Application

Service
3 to Over
10 10
Hour Hour

AGITATORS
Pure Liquids............................................ 1.00 1.25
Liquids & Solids...................................... 1.25 1.50
Liquids-Variable Density.......................... 1.25 1.50
APRON CONVEYORS
Uniformly-Loaded or Fed......................... 1.25 1.50
Heavy-Duty.............................................. 1.25 1.50
APRON FEEDERS................................. 1.25 1.50
ASSEMBLY CONVEYORS
Uniformly-Loaded or Fed......................... 1.25 1.25
Heavy-Duty.............................................. 1.25 1.50
BALL MILLS......................................... See Mills, Rotary
BARGE HAUL PULLERS...................... 1.75 2.00
BARKING
Drums (Coupling Connected)..................
2.00
Mechanical...............................................
2.00
BAR SCREENS (Sewage)................... 1.25 1.25
BATCHERS (Textile)............................ 1.25 1.50
BELT CONVEYORS
Uniformly-Loaded or Fed......................... 1.25 1.25
Heavy-Duty.............................................. 1.25 1.50
BELT FEEDERS..................................... 1.25 1.50
BENDING ROLLS (Machine).............. 1.25 1.50
BLOWERS
Centrifugal............................................... 1.25 1.25
Lobe......................................................... 1.25 1.50
Vane......................................................... 1.25 1.50
BOTTLING MACHINERY...................... 1.00 1.25
BREWING............................................... See Table 2
BRICK PRESS (Clay Working)........... 1.75 2.00
BRIQUETTE MACHINES
(Clay Working)..................................... 1.75 2.00
BUCKET
Conveyors Uniform.................................. 1.25 1.50
Conveyors Heavy-Duty............................ 1.25 1.50
Elevators Continuous............................... 1.25 1.50
Elevators Uniform.................................... 1.25 1.50
Elevators Heavy-Duty............................... 1.25 1.50
CALENDERS
Rubber and Plastic.................................... See Table 2
Textile....................................................... 1.25 1.50
CANE KNIVES........................................
1.75
CAN FILLING MACHINES.................... 1.00 1.25
CARD MACHINES (Textile)................. 1.25 1.50
CAR DUMPERS..................................... 1.75 2.00
CAR PULLERS...................................... 1.25 1.50
CEMENT KILNS.................................... See Mills, Rotary
CENTRIFUGAL
Blowers, Compressors, Discharge
Elevators, Fans or Pumps................ 1.25 1.25
CHAIN CONVEYORS
Uniformly-Loaded or Fed......................... 1.25 1.25
Heavy-Duty.............................................. 1.25 1.50
CHEMICAL FEEDERS (Sewage)........ 1.25 1.25
CLARIFIERS.......................................... 1.00 1.25
CLASSIFIERS........................................ 1.25 1.50
CLAY WORKING.................................... See Table 2
COLLECTORS (Sewage)..................... 1.25 1.25
COMPRESSORS
Centrifugal............................................... 1.25 1.25
Lobe......................................................... 1.25 1.50
Reciprocating
Multi-Cylinder.................................. 1.50 1.75
Single-Cylinder................................ 1.75 2.00
CONCRETE MIXERS
Continuous.............................................. 1.25 1.50
Intermittent............................................... 1.25 1.50

Application
CONVEYORS

Service
3 to Over
10 10
Hour Hour

UniformlyLoaded or Fed
Apron or Bucket................................ 1.25 1.50
Assembly, Belt, Chain, Flight, Oven,
Screw.............................................. 1.25 1.25
CONVEYORS Heavy-Duty,
Not Uniformly Fed
Apron, Assembly, Belt, Bucket,
Chain, Flight, Oven, Screw.............. 1.25 1.50
CONVEYORS Severe Duty
Live Roll.................................................... Refer to Factory
Reciprocating Shaker............................... 1.75 2.00
COOKERS (Brewing & Distilling),
(Food)..................................................... 1.25 1.25
COOLING TOWER FANS........................Refer to Factory
CRANES
Dry Dock Cranes, Main Hoist,
Bridge and Trolley Travel......................... Refer to Factory
CRUSHERS
Ore or Stone............................................. 1.75 2.00
Sugar.......................................................
1.75
DEWATERING SCREENS (Sewage).. 1.50 1.50
DISC FEEDERS..................................... 1.00 1.25
DISTILLING............................................ See Table 2
DOUBLE ACTING PUMPS
2 or more Cylinders................................. 1.25 1.50
Single-Cylinder..........................................Refer to Factory
DOUGH MIXER (Food)........................ 1.25 1.50
DRAW BENCH (Metal Mills)
Carriage & Main Drive............................. 1.25 1.50
DREDGES............................................... See Table 2
DRY DOCK CRANES............................. Refer to Factory
DRYERS & COOLERS (Mills,
Rotary)...................................................
1.50
DYEING MACHINERY (Textile).......... 1.25 1.50
ELEVATORS
Bucket-Uniform Load............................... 1.25 1.50
Bucket-Heavy-Duty.................................. 1.25 1.50
Bucket-Continuous.................................. 1.25 1.50
Centrifugal Discharge............................... 1.25 1.25
Escalators ........................................... Not Approved
Freight ................................................ Not Approved
Gravity Discharge..................................... 1.00 1.25
Man Lifts, Passenger .......................... Not Approved
EXTRUDERS (Plastic & Rubber)........ See Table 2
FANS
Centrifugal............................................... 1.25 1.25
Cooling Towers......................................... Refer to Factory
Forced Draft.............................................
1.25
Induced Draft........................................... 1.50 1.50
Large (Mine, etc.)..................................... 1.50 1.50
Large lndustrial........................................ 1.50 1.50
Light (Small Diameter)............................. 1.00 1.25
FEEDERS
Apron, Belt............................................... 1.25 1.50
Disc......................................................... 1.00 1.25
Reciprocating........................................... 1.75 2.00
Screw....................................................... 1.25 1.50
FLIGHT CONVEYORS
Uniform.................................................... 1.25 1.25
Heavy....................................................... 1.25 1.50
FOOD INDUSTRY.................................. See Table 2
GENERATORS (Not Welding)............ 1.00 1.25
GRAVITY DISCHARGE ELEVATORS.. 1.00 1.25
HAMMER MILLS.................................. 1.75 2.00

Application

Service
3 to Over
10 10
Hour Hour

HOISTS
Heavy-Duty.............................................. 1.75 2.00
Medium Duty........................................... 1.25 1.50
Skip Hoist................................................ 1.25 1.50
INDUCED DRAFT FANS....................... 1.50 1.50
KILNS.................................................... See Mills, Rotary
LAUNDRY WASHERS.......................... 1.50 2.00
LAUNDRY TUMBLERS........................ 1.25 1.50
LINE SHAFTS
Driving Processing Equipment................. 1.25 1.50
Other Line Shafts, Light........................... 1.00 1.25
LIVE ROLL CONVEYORS.......................Refer to Factory
LOBE BLOWERS OR
COMPRESSORS................................... 1.25 1.50
LOG HAULS (Lumber).........................
Incline-Well Type..................................... 1.75 1.75
LOOMS (Textile)................................... 1.25 1.50
LUMBER INDUSTRY............................ See Table 2
MACHINE TOOLS
Auxiliary Drives........................................ 1.00 1.25
Bending Rolls........................................... 1.25 1.50
Main Drives.............................................. 1.25 1.50
Notching Press (Belted).............................Refer to Factory
Plate Planers............................................ 1.75 2.00
Punch Press (Geared).............................. 1.75 2.00
Tapping Machines.................................... 1.75 2.00
MANGLE (Textile)................................ 1.25 1.50
MASH TUBS (Brewing & Distilling). 1.25 1.25
MEAT GRINDERS (Food).................... 1.25 1.50
METAL MILLS
Draw Bench Carriages & Main Drives...... 1.25 1.50
Pinch, Dryer & Scrubber Rolls,
Reversing................................................. Refer to Factory
Slitters..................................................... 1.25 1.50
Table Conveyors
Non-Reversing Group Drives............ 1.50 1.50
Non-Reversing Individual Drives...... 2.00 2.00
Reversing.......................................... Refer to Factory
Wire Drawing & Flattening Machines....... 1.25 1.50
Wire Winding Machines........................... 1.50 1.50
MILLS, ROTARY
Ball and Rod Mills
with Spur Ring Gear.........................
2.00
with Helical Ring Gear......................
1.50
Direct Connected..............................
2.00
Cement Kilns, Dryers & Coolers, Pebble,
1.50
Plain & Wedge Bar Mills........................
Tumbling Barrels...................................... 1.75 2.00
MIXER (Also see Agitators)
Concrete, Cont. & lnt............................... 1.25 1.50
Constant Density...................................... 1.25 1.50
Variable Density....................................... 1.25 1.50
NAPPERS (Textile)............................... 1.25 1.50
OIL INDUSTRY...................................... See Table 2
ORE CRUSHERS................................... 1.75 2.00
OVEN CONVEYORS
Uniform.................................................... 1.25 1.25
Heavy-Duty.............................................. 1.25 1.50
PAPER MILLS....................................... See Table 2
PASSENGER ELEVATORS .............. Not Approved
PEBBLE MILLS.....................................
1.50
PLATE PLANERS.................................. 1.75 2.00
PRINTING PRESSES..............................Refer to Factory
PROPORTIONING PUMPS.................. 1.25 1.50
PUG MILLS (Clay)............................... 1.25 1.50
PULLERS (Barge Haul)....................... 1.75 2.00

Application

Service
3 to Over
10 10
Hour Hour

PUMPS
Centrifugal............................................... 1.25 1.25
Proportioning........................................... 1.25 1.50
Reciprocating
Single-Act., 3 or more Cyl................ 1.25 1.50
Double-Act., 2 or more Cyl............... 1.25 1.50
Single-Act., 1 or 2 Cyl...................... Refer to Factory
Double-Acting, 1 Cyl........................ Refer to Factory
Rotary: Gear, Lobe, Vane.......................... 1.00 1.25
PUNCH PRESSES
(Gear-Driven)....................................... 1.75 2.00
RECIPROCATING
Conveyors & Feeders............................... 1.75 2.00
RECIPROCATING COMPRESSORS
Multi-Cylinder......................................... 1.50 1.75
Single-Cylinder........................................ 1.75 2.00
ROD MILLS.......................................... See Mills, Rotary
ROTARY
Pumps..................................................... 1.00 1.25
Screens (Sand or Gravel)......................... 1.25 1.50
RUBBER & PLASTICS INDUSTRIES. See Table 2
SAND MULLERS................................... 1.25 1.50
SCREENS
Air Washing............................................. 1.00 1.25
Rotary Sand or Gravel........................ 1.25 1.50
Traveling Water Intake.............................. 1.00 1.25
SCREW CONVEYORS..........................
Uniform.................................................... 1.25 1.25
Heavy-Duty or Feeder............................... 1.25 1.50
SCUM BREAKERS (Sewage)............. 1.50 1.50
SEWAGE DISPOSAL............................ See Table 2
SHAKER CONVEYORS......................... 1.75 2.00
SHEETERS (Rubber)............................
1.50
SINGLE-ACTING PUMP
I or 2 Cylinders......................................... Refer to Factory
3 or more Cylinders................................. 1.25 1.50
SKI TOWS & LIFTS........................... Not Approved
SKIP HOIST....................................... 1.25
1.50
SLAB PUSHERS.................................... 1.50 1.50
SLITTERS (Metal)................................ 1.25 1.50
SLUDGE COLLECTORS (Sewage)..... 1.25 1.25
SOAPERS (Textile)............................... 1.25 1.50
SPINNERS (Textile)............................. 1.25 1.50
STEERING GEARS..................................Refer to Factory
STOKERS............................................... 1.00 1.25
STONE CRUSHERS.............................. 1.75 2.00
SUGAR INDUSTRY................................ See Table 2
TABLE CONVEYORS
(Non-Reversing)
Group Drives............................................ 1.50 1.50
Individual Drives...................................... 2.00 2.00
Reversing.................................................. Refer to Factory
TENTER FRAMES (Textile)................. 1.25 1.50
TEXTILE INDUSTRY............................. See Table 2
THICKENERS (Sewage)...................... 1.50 1.50
TUMBLING BARRELS.......................... 1.75 2.00
VACUUM FILTERS (Sewage)............. 1.50 1.50
VANE BLOWERS................................... 1.25 1.50
WINCHES (Dredges)........................... 1.25 1.50
WINDERS (Textile).............................. 1.25 1.50
WINDLASS..............................................Refer to Factory
WIRE
Drawing Machines................................... 1.25 1.50
Winding Machines................................... 1.50 1.50

Selection of Rexnord products for applications whose primary purpose is the transportation of people is not approved. This includes such applications as freight or passenger
elevators, escalators, man lifts, work lift platforms and ski tows and ski lifts. If the primary purpose of the application is material conveyance and occasionally people are transported,
the Factory warranty may remain in effect provided the design load conditions are not exceeded and certification to the appropriate safety codes and load conditions has been obtained
by the system designer or end user from the appropriate enforcement authorities.
Contact Rexnord for proper selection of a Falk RAM mixer drive.

Rexnord 2014

(131-110) 7

How to Select an A-Plus Drive


Before making a selection, please refer to Basic Information and Conditions Affecting
Selections on pages4 and 5, and note in particular the paragraphs referring to
Gear Drive Ratings, Application-Adjusted Thermal Rating and Speed Variation.

Horsepower Selection Method

Information Required

1. Determine the Service Factor for the application from Table 2 or Table 3 on
pages6 and 7. These tables apply for electric-motor-driven applications
operating between 3 and 10 hours or over 10 hours per day. For occasional and
intermittent service, or for engine-driven applications, refer to Table 1, page6.

The following basic information is required to select an A-Plus gear drive for your
application.
Prime Mover
Type electric or hydraulic motor or engine
Power rating in hp or kW
Speed constant or variable
Mounting position if inclined
Dimensions if Rexnord will furnish motor mounting accessory or coupling
Driven Machine
Type conveyor, kiln, etc.
Power load, brake hp, or required torque
Speed
Service Hours per day; reversals per minute if reversing; minutes per hour (duty
cycle) if not continuous
Gear Drive
Type parallel shaft or right angle
Horizontal or vertical output shaft
Ambient temperature at drive location
Altitude above sea level
Ambient air velocity at drive location
Shaft Connections

Selection with the horsepower selection method is based on the power rating of the
prime mover. The procedure is:

2. Calculate equivalent horsepower by multiplying the prime mover horsepower by the


Service Factor determined in step 1. If momentary or peak load will exceed 200% of
the rated load, refer to the paragraph Excessive Overloads under Conditions Affecting
Selection on page5.
3. Determine the gear drive ratio by dividing the high-speed shaft rpm by the low-speed
shaft rpm.
4. Select the size and nearest standard ratio from the Horsepower Rating Table
for parallel shaft drives, pages17-32, or for right-angle drives,
pages67-76. Opposite the high-speed shaft rpm, and the desired ratio
and output speed, trace right to a horsepower rating that equals or exceeds the
equivalent horsepower calculated in Step 2. Read the size of the gear drive at the
top of the column. For ratings at speeds higher than 1750 rpm, contact your local
Rexnord district office. For ratings at speeds below 580 rpm, reduce the rating
proportionately.
Torque Selection Method
Simply follow the steps outlined in the horsepower method, substituting torque values for
horsepower values.
To check thermal capacity, convert the actual required torque to horsepower and check
against the thermal rating. To convert, use the torque (lb-in) and speed (rpm) at lowspeed shaft of the drive in the following formula:
HP =

Torque (lb-in) x Output Speed (RPM)


63,000

Shaft diameters and key sizes


Overhung loads diameter and type of sheave, sprocket or pinion
Thrust load and direction

General Selection Procedure


The general selection procedure consists of the following steps:
1. Select the type of drive parallel shaft, right-angle, horizontal or vertical output
shaft.
2. Determine drive size using either the horsepower selection method or the torque
selection method.
3. Check thermal rating of the selected drive to determine if it is sufficient for the
application. If necessary, select a cooling device (fan, cooling tubes, etc.) or a larger
drive with sufficient thermal capacity.
4. If there are external shaft loads (overhung load and thrust), check to determine if they
are within the drive ratings.

8 (131-110)

Rexnord 2014

How to Select an A-Plus Drive


Checking Thermal Rating

Table 5 Altitude Factor B2 (For air cooling only, no cooling tubes)

Checking the thermal rating is extremely important. If the drive creates heat faster than it
can be dissipated, it will overheat, and severe damage may occur.

Altitude ft, Sea Level = 0

Factor with or without Auxiliary Cooling

0 to 2,500

1.00

The thermal rating of a drive is the actual power in horsepower (without Service Factor)
that a drive can transmit continually for three hours or more without overheating.

2,500

0.95

Thermal ratings must be considered when the continuous operating period exceeds
three hours, or if operation exceeds three hours and the running time is greater than the
shutdown time.

5,000

0.90

7,500

0.85

10,000

0.81

Application-Adjusted Thermal Rating

12,500

0.76

The application-adjusted thermal rating must be greater than the actual power transmitted
through the gear drive (frequently the power rating of the driving motor is used rather
than the actual power transmitted). To determine the application-adjusted thermal rating,
look up the basic thermal rating for the drive size and ratio selected, pages33-38
for parallel shaft drives and pages77-79 for right-angle drives. Determine the
application-adjusted thermal rating by using the appropriate correction factors (Table
4 through Table 8). Compare the actual power rating required (without Service
Factor) with the application-adjusted thermal rating. If the actual power rating exceeds
the application-adjusted thermal rating, shaft fans, electric fans or cooling tubes may
be added, an optional heat exchanger package may be added, or a larger drive may be
selected. Review all the footnotes for the basic thermal rating to be certain which cooling
accessories are available for the selected drive.

15,000

0.72

17,500

0.68

Application-adjusted thermal rating is determined using the following:


PTA = B1 x B2 x B3 x B4 x B5 x PT where:
PTA = application-adjusted thermal rating
PT = Basic thermal rating from the tables in this catalog
B1 = Ambient temperature factor from Table 4
B2 = Altitude factor from Table 5 (used only for air cooling)
B3 = Ambient air velocity factor from Table 6 (used only if no auxiliary cooling is used)
B4 = Inlet water temperature factor from Table 7 (used only when cooling tubes are
selected)
B5 = Duty cycle factor from Table 8
Ambient Temperature

Sustained Ambient Air


Velocity fpm

Installed Environment

Factor without
Shaft or Electric Fan
or Cooling Tubes

Less than 100 fpm


(1 mph)

Small Confined Space

0.75

Between 100 fpm & 275 fpm


(1 to 3 mph)

Large Indoor Room

1.00

Between 275 fpm & 725 fpm


(3 to 8 mph)

Large Indoor Room

1.40

Greater than 725 fpm


(8 mph)

Outdoors

1.90

The sustained ambient air velocity must be a continuous flow of air directly onto
the gear drive. If the airflow cannot be counted on to be continuous, an ambient air
velocity factor of 1.00 must be used.
Table 7 Inlet Water Temperature Factor B4 (For drives with cooling
tubes only)
Inlet Water Temperature

Factor with Cooling Tubes Only

50F

1.11

Factor with Cooling Tubes

60F

1.05
1.00

Table 4 Ambient Temperature Factor B1 (For all cooling methods)


Factor with or without
Shaft or Electric Fan

Table 6 Ambient Air Velocity Factor B3 (For no auxiliary cooling only)

50F

1.19

1.06

70F

60F

1.13

1.04

80F

0.94

70F

1.07

1.02

90F

0.88

100F

0.83

80F

1.00

1.00

90F

0.93

0.98

100F

0.85

0.96

110F

0.78

0.94

120F

0.69

0.91

Factors for other ambient temperatures can be interpolated.

Table 8 Duty Cycle Factor B5 (For all cooling methods)


% Operating Time Per Hour

Factor with or without Auxiliary Cooling

100%

1.00

80%

1.05

60%

1.15

40%

1.35

20%

1.80

The duty cycle factor must be based on the percentage of each hour that the drive
is operating. For example: a gear drive operating for 48 minutes and resting for 12
minutes every hour of the day has an 80% duty cycle, but a drive operating for four
hours and resting for four hours has a 100% duty cycle. Where % run time per hour
falls between values shown above, use next higher % run time.

Rexnord 2014

(131-110) 9

How to Select an A-Plus Drive


Shaft Ratings

Torque Selection Example

High-speed and low-speed shaft ratings should be checked if the application involves an
applied bending moment, for example a sheave, sprocket, pinion or some type of rigid
coupling on either shaft. In addition, drives with vertical low-speed shafts should be
checked to determine if any thrust that could be applied to the shaft is within the limits of
the shaft.

A dredge requires 190,000 lb-in torque at its output shaft, and operates at 13 rpm. The
winch is in service 10 hours per day and is driven by a flexible coupling-connected
50 hp, 1170 rpm electric motor. The ambient temperature never exceeds 100F. Although
the dredge operates outdoors, the average sustained wind velocity is only 5 mph. The
dredge operates on the Great Lakes which can be considered to be near sea level. The
winch never operates more than 45 minutes in any given hour. The space available is best
suited to a right-angle gear drive. Select a gear drive for this application.

Shaft ratings for parallel shaft drives are found on pages39-46. Right-angle drive
shaft ratings are found on pages80-83. Instructions for using these ratings are
also found on these pages.

Horsepower Selection Example


A draw bench requiring 135 brake hp operates 10 hours per day at 30 rpm, and is driven
by a 150 hp, 1170 rpm electric motor. Ambient temperature at the draw bench never
exceeds 90F. The draw bench is located in a large indoor room, but airflow in the area
is only 200 fpm. The high-speed and low-speed shafts will be connected to the drive and
driven equipment with flexible shaft couplings. Select a parallel shaft gear drive for this
application.
1. The Service Factor is 1.25 for a draw bench drive operating 10 hours per day from
page7, Table 3.
2. The equivalent hp = 1.25 x 135 = 169 hp.
3. The required ratio is 1170 30 = 39. The closest standard ratio is 38.44 from the
Triple Reduction Selection Table on page25.
4. Using the Triple Reduction Selection Table on page25, in the 1170 rpm highspeed shaft section opposite the 38.44:1 ratio and 30 rpm, trace right to 181 (nearest
hp exceeding the equivalent hp of 169) and read the drive size 425 at the top of the
column.
5. The basic thermal capacity for a 425A3, 38.44:1, at 1170 rpm with no auxiliary
cooling from the Basic Thermal Rating Table on page37 is 120 hp.
6. The ambient temperature factor (B1) is 0.93 from Table 4, and the altitude factor (B2)
and ambient air velocity factor (B3) are 1.0 from Table 5 and Table 6. The duty
cycle factor (B5) is 1.0 from Table 8.

1. The Service Factor is 1.25 for a dredge winch drive operating 10 hours per day from
page7, Table 3 under Winches (Dredges).
2. The equivalent torque is 1.25 x 190,000 = 237,500 lb-in.
3. The required ratio is 1170 13 = 90. The closest standard ratio is 86.5 from the
Quadruple Reduction Selection Table on page74.
4. Using the Quadruple Reduction Table on page74, in the 1170 rpm high-speed
shaft section opposite 85.60:1 ratio and 13.5 rpm, trace right to 253 ( x 1000,
nearest torque exceeding the equivalent torque of 237,500 lb-in) and read the drive
size 405 at the top of the column.
5. The basic thermal capacity with no auxiliary cooling for a 405, 86.50:1 at 1170
rpm from the table on page79 is 56.2 hp. The ambient temperature factor (B1)
from Table 4, page9, is 0.85. The altitude correction factor (B2) is 1.0 from
Table 5, page9. The ambient air velocity factor (B3) is 1.4 from Table 6,
page9. The duty cycle is 75% (45 min/60 min), so the duty cycle factor is 1.05
from Table 8, page9.
6. The application-adjusted thermal capacity is 56.2 x 0.85 x 1.0 x 1.4 x 1.05 = 70.2 hp
which exceeds the hp rating of the motor (50 hp). Therefore, no additional cooling
is required.
7. Shaft ratings do not need to be checked because the drive is connected by flexible
couplings at both the high-speed and low-speed shafts. Refer to Rexnord coupling
catalogs for coupling selections.

7. The application-adjusted thermal capacity is 120 x 0.93 x 1 x 1 x 1 = 111.6 hp. This


is not adequate because the actual brake hp is 135 hp.
8. The basic thermal capacity for a 425A3, 38.44:1 with two shaft fans is 170 hp. This is
adequate since 158.1 (170 x 0.93 x 1 x 1) is greater than the 135 hp required. Note
that the ambient air factor (B3) is no longer used the in the calculation of applicationadjusted thermal capacity because the drive is now fan-cooled.
9. Shaft ratings do not need to be checked because the drive is connected by flexible
couplings at both the high-speed and low-speed shafts. Refer to Factory coupling
catalogs for coupling selections.

10 (131-110)

Rexnord 2014

Accessory & Option Information


Cooling Accessories

Cooling Tubes

Shaft-Driven Cooling Fans

Falk cooling tubes are an economical alternative for thermal requirements that are beyond
the capability of fans. A series of straight, finned tubes are provided directly in the oil
sump of the drive. Water is circulated through these tubes to cool the oil. Since there are
no joints or connections inside the drive, leakage of water into the oil sump is eliminated.
The thermal ratings shown in this catalog are for 70F (21C) inlet water temperature.
Refer to Table 7 on page9 for determining thermal ratings with other cooling water
temperatures. Dimensions are shown on pages105-108.

Shaft-driven cooling fans have been successfully used on electric motors and other
related machinery for many years. They eliminate the need for water or electrically
powered cooling, pumps, external piping or wiring. Less than 0.25% of cataloged power
rating is required to drive the fans. Shaft-driven fans are available for use with A and AR
parallel shaft drives and AB, ABR and ABX right-angle drives. Mounting locations and
dimensions are shown on pages99-101.

Water flow rates to attain cooling tube basic thermal ratings as shown on
pages35-38, and pages77-79 are as follows:
Sizes 305 through 535 = 2 gallons per minute
Sizes 545 through 585 = 5 gallons per minute

Pump & Cooler Assemblies


Rexnord offers Pump & Cooler Assemblies when requirements exceed the thermal
capacity of shaft fans, electric fans or cooling tubes. For detailed information, refer to the
following Selection Guides:
131-310, Type PC Pump & Cooler Assemblies (Water/Oil)
131-315, Type PA Pump & Cooler Assemblies (Air/Oil)

Electric Cooling Fans


Electric fans achieve greater thermal capacities than shaft-driven fans and include a
temperature switch to turn off the fan when it is not required. Mounting locations and
dimensions are shown on pages102-104. The following electric fan motor packages
are available for all sizes and reductions:
60 Hz, 3-Phase, 220/380 VAC
60 Hz, 3-Phase, 265/460 VAC
50 Hz, 3-Phase, 220/380 VAC
Pre-selected fan motor packages at 60 Hz, Single Phase, 110 VAC or 220 VAC may also
be available, see Electric Cooling Fan Selection Guide 131-320 for details.
Electric fan motor packages not conforming to the above are also available, but must be
specially selected. Consult Rexnord for price and delivery.
The electric fan motor starter is not included in electric fan motor packages offered by
Rexnord.

Rexnord 2014

(131-110) 11

Accessory & Option Information


Motor Attachment Accessories

Flanged Motor Adapters

Motor Brackets

Falk flanged motor adapters are available for Types AR, AXV, ABR and ABX drives. This
adapter allows a flange-mounted motor to be directly mounted to the high-speed side of
the drive. Contact Rexnord for further details on this accessory.

Motor brackets provide an economical option for mounting electric motors to gear drives.
Due to the large variation in motor sizes/weights/starting torques/ & mounting positions
(determined by coupling types), some motor bracket installations may deflect and vibrate
beyond levels considered satisfactory to the end user.
When a motor bracket is purchased as the motor mounting structure, it becomes the
customers responsibility to support the motor bracket as necessary to diminish motor
bracket deflection and vibration to satisfactory levels as determined by the end user. This
may be accomplished with jacking screws or by adding other structural supports in the
field.
Motor plates or special bedplates are recommended for applications subjected to high
system vibration, torque fluctuations, impact loads, or other installations that require
rigidly mounted machinery
For detailed information on motor brackets, see motor bracket dimension sheets as
follows:
Type A, Engineering 137-650
Type AR, Dimensions 135-554 & 135-556
Type AXV, Dimensions 135-564 & 135-566
Type ABR, Dimensions 235-672 & 235-674
Type ABX, Dimensions 235-676 & 235-678

Bedplates
A bedplate is recommended to ensure proper alignment of the drive with the motor.
Rexnord offers a complete line of fabricated steel bedplates for all popular sizes of
standard Type A and AB drives. These bedplates accommodate standard NEMA and IEC
motors within the power range of the drive and many of the larger non-NEMA motors.
Special bedplates can be designed and manufactured for unique motor and special
accessory combinations.
Versatile welded steel construction permits rapid modification of standard bedplates by
addition or deletion. Supports for tachometers, brakes, timing devices, foot-mounted
fluid couplings or other accessories can also be added. Contact Rexnord for further
details on this accessory.

Motor Mounts
Falk motor mounts are selectively pre-designed for Types ABR and ABX drives. Motor
mounts provide a convenient drive support for the motor when the drive is belt- or
chain-driven.
For detailed information on motor mounts, see motor mount dimension sheets as
follows:
Type ABR, Dimensions 235-652 & 235-654
Type ABX, Dimensions 235-662

12 (131-110)

Orange Peel Guards


Orange Peel guards patented trim-and-fit design revolutionizes equipment guard
convenience and value, so you can get the job-site safety you want without the expense
and long lead times of custom engineered guards.

Rexnord 2014

Accessory & Option Information


Backstops

Alignment-Free Drive Package

Backstops prevent reverse rotation or backrun without backlash for conveyors, elevator
head shafts and similar applications. Rexnord offers a standard line of accessory
backstops for use on Type A, AR, AB and ABR drives.

The Alignment-Free Drive is a standard packaged drive developed by Rexnord to meet the
demands of surface and underground belt conveyor applications. The drive comprises a
unitized motor, coupling (fluid or flexible) and right-angle gear drive that mounts directly
to the conveyor drive shaft and is supported by a single torque arm. It is simple to install,
eliminates the cost of expensive mounting pads, and offers the mobility required for
todays conveyor systems. For more information about the Alignment-Free Drive refer to
the Falk Alignment-Free Drives Selection Guide (231-210).

These accessory backstops are mounted externally on an extension of either the highspeed (A and AR) or an intermediate shaft (AB and ABR). When Type A parallel shaft
drives are equipped with accessory backstop mounted at the high-speed shaft, only one
shaft-driven fan can be mounted; the two shaft fan option is not available.
See Falk Backstop Selection Guide (136-610) for availability, selection and dimensions
of Falk accessory backstops for Type A and AR parallel shaft gear drives. For dimensions
of pre-selected accessory backstops for Type AB right-angle shaft gear drives, see
dimension sheet 235-610. For heavy-duty backstopping requirements, refer to Falk NRT
Low-Speed Backstop Selection Guide (561-110).
When specifying accessory backstops, the overrunning direction of rotation is defined
as clockwise or counterclockwise when facing the rotating end of the low-speed shaft
extension.

Airmax Breather & Sealed Dipstick


A Falk exclusive, the Airmax is specially designed to allow the drive to breathe, while
excluding airborne particles and moisture. For the full benefit of the Airmax, also specify
the sealed dipstick feature. For further details, see Selection Guide 111-210.

Dry Well Feature

Magnetic Drain Plug

(Types AXVD, AXVQ, ABXD & ABXQ)

The magnetic drain plug attracts harmful metal particles and provides early warning of
abnormal wear. Magnetic drain plugs are furnished as standard for Drive Types A, AR,
AXV, AB, ABR & ABX as follows:

For vertical low-speed shaft types listed above, a dry well at the low-speed shaft is
incorporated as standard. In this case the lower bearing is grease-lubricated, and the
low-speed seal does not retain a head of oil.

Drive Sizes 305-345 = 1.00"-11.5 NPT Drain Plug


Drive Sizes 365-585 = 1.25"-11.5 NPT Drain Plug

Rexnord 2014

(131-110) 13

Gear Drive Nomenclature


425
Drive Size
305
325
345
365
385
405
425
445
465
485
505
525
535
545
555
565
585

AR

Mounting
Reduction
Model
A, B, C, etc.
+ Foot-Mounted, Solid LSS
+ Shaft-Mounted, Solid LSS, Moment Connection, Torque Arm
+ Flange-Mounted, Solid LSS
+ Shaft-Mounted, Solid LSS, Moment Connection, Torque Arm
+ Shaft-Mounted, Hollow LSS w/Shrink Disc, Torque Arm
+ Foot-Mounted, Hollow LSS w/Keeper Plate
+ Foot-Mounted, Solid LSS (Down)
+ Foot-Mounted, Solid LSS (Up)
+ Foot-Mounted, Solid LSS
+ Shaft-Mounted, Solid LSS, Moment Connection, Bedplate &
Torque Arm
ABR
= Right-Angle, Horizontal + Flange-Mounted, Solid LSS
ABRM = Right-Angle, Horizontal + Shaft-Mounted, Solid LSS, Moment Connection, Torque Arm
ABRJ = Right-Angle, Horizontal + Shaft-Mounted, Hollow LSS w/Shrink Disc, Torque Arm
+ Foot-Mounted, Hollow LSS w/Keeper Plate
ABXQ = Right-Angle, Vertical
+ Foot-Mounted, Solid LSS (Down)
ABXD = Right-Angle, Vertical
ABXU = Right-Angle, Vertical
+ Foot-Mounted, Solid LSS (Up)
A
AM
AR
ARM
ARJ
AXVQ
AXVD
AXVU
AB
ABM

Type
= Parallel Shaft, Horizontal
= Parallel Shaft, Horizontal
= Parallel Shaft, Horizontal
= Parallel Shaft, Horizontal
= Parallel Shaft, Horizontal
= Parallel Shaft, Vertical
= Parallel Shaft, Vertical
= Parallel Shaft, Vertical
= Right-Angle, Horizontal
= Right-Angle, Horizontal

A
B
C
D
E
F
G
H
R
S
T
Z

413.7

Variations
= With Backstop
= With Fan(s)
= With Backstop & Fan(s)
= With Double-Ended LSS
= With Single-Ended HSS
= With Flanged Motor
Adapter
= With Motor Mount
= With Tie Rod
= With Any Combination
of Variations
= Special Features
= With Cooling Tubes
= With Motor Bracket

Ratio
Exact ratio
expressed
to four
digits.

See Availability Table below for availability of drive types.


Parallel Shaft Gear Drives
A - Foot-Mounted
AM - Shaft-Mounted
Solid Shaft
Solid Shaft with Moment Connection

AXVQ - Foot-Mounted
Hollow Shaft with Keeper Plate

AR - Flange-Mounted
Solid Shaft

ARM - Shaft-Mounted
Solid Shaft with Moment Connection

AXVD - Foot-Mounted
Solid Shaft (Down)

AXVU - Foot-Mounted
Solid Shaft (Up)

Right Angle Shaft Gear Drives


AB - Foot-Mounted
ABM - Shaft-Mounted
Solid Shaft
Bedplate/Solid Shaft with Moment Connection

ABXQ - Foot-Mounted
Hollow Shaft with Keeper Plate

ABR - Flange-Mounted
Solid Shaft

ABRM - Shaft-Mounted
Solid Shaft with Moment Connection

ABXD - Foot-Mounted
Solid Shaft (Down)

ABXU - Foot-Mounted
Solid Shaft (Up)

ARJ - Shaft-Mounted
Hollow Shaft with Shrink Disc

ABRJ - Shaft-Mounted
Hollow Shaft with Shrink Disc

Availability Table (by Type and Reduction)


(An X indicates that the gear drive type and reduction are available for a given size.)
Drive
Size
305
325
345
365
385
405
425
445
465
485
505
525
535
545
555
565
585

A1

A2

A3

A4

AR2

AR3

AR4

X
X
X
X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X
X
X
X

X
X

X
X
X
X
X
X
X
X
X
X
X
X

X
X

X
X
X
X
X
X
X
X

X
X
X
X
X
X

X
X
X
X
X
X

X
X
X
X
X
X

Type and Reduction


AXV2
AXV3
AXV4

X
X
X
X
X
X

14 (131-110)

X
X
X
X
X
X

X
X
X
X
X
X

AB2

AB3

AB4

ABR3

ABR4

ABX3

ABX4

X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X

X
X

X
X
X
X
X
X
X
X

X
X

X
X
X
X
X
X

X
X
X
X
X
X

X
X
X
X
X
X

X
X
X
X
X
X

Rexnord 2014

How to Order an A-Plus Drive


The following information is required to order an A-Plus drive to meet your requirements.
Much of the information is also used to make a selection and is repeated here in case a
selection will be made by a Rexnord district office. Note that it is not necessary to specify
nomenclature, as described on page14, when ordering an A-plus drive.
Drive
Size, type and ratio.
Input and output speed (rpm).
Service Factor for application.
External shaft loads thrust and overhung load.
Factors affecting thermal performance ambient temperature, altitude, ambient air
velocity, duty cycle and inlet water temperature (if cooling water is to be used).

Auxiliary Equipment
Motors if Rexnord is to furnish, provide complete specifications.
Bedplates supply drawing of motor and any auxiliary equipment not supplied by
Rexnord.
Flanged motor adapters or motor brackets supply drawing of motor.
Motor mount supply drawing of motor and the required belt centers and mounting
arrangement.
Backstops specify direction of rotation of the low-speed shaft (CW or CCW) when
looking toward the drive from the low-speed end.
Electric fan position.
Couplings specify size, type, drive and driven hub bores and keyways.

Auxiliary equipment required couplings, backstops, etc.

Mounting position and shaft assembly number (see page16 for parallel shaft
drives and page66 for right-angle drives).

Motor Prime Mover


G

Type motor or engine.


D

Power rating hp or kW.

Speed rpm.
Frame size dimension prints if Rexnord is to furnish mounting surface and/or
mount the equipment.

B & E = Max. Coupling Dimensions


D & F = Exposed Shaft

Motor type, class, weight or any special characteristics (such as brakemotor,


explosion-proof, etc.).

Coupling guards furnish description of couplings and/or other equipment to be


guarded, and all dimensions A through G above.

Identify if motor is to be furnished or installed by Rexnord.

Special or Specification Requirements

Driven Machine

Advise Rexnord of any special project-related specifications such as: noise level
specifications, bearing L10 requirements, etc.

Required power or torque.


Speed rpm.
Application description belt conveyor, agitator, etc.
Service duty cycle, hours per day, reversals per minute if reversing.
Ambient temperature and operating conditions outdoor, taconite dust, etc.

Type A Assemblies
Drives with Rifle-Drilled Low-Speed Shaft for Air Clutch
AIR CLUTCH
ROTO
SEAL

AIR CLUTCH

AIR CLUTCH
ROTO
SEAL

34

35

AIR CLUTCH
ROTO
SEAL

ROTO
SEAL

36

Rexnord 2014

37

(131-110) 15

Type A Drive Selection


Shaft Assemblies & Rotations
Type A, AR, ARJ & AXV
Drives with rifle-drilled low-speed shaft for air clutch See Page 16.
Please specify from the views below, the desired assembly number. High-speed shaft overhung load capacities published on pages39-44 apply to either high-speed shaft
extension. The low-speed shaft overhung load capacities published on pages44 and 45 apply to the low-speed shaft extensions below with heavy arrows. Published overhung load
capacities may be increased when an outboard bearing is used. Consult Rexnord for overhung load capacities of low-speed shaft extensions without the heavy arrow, as they are less than
the heavy arrow extensions.
Contact Rexnord for inclined, wall-mounted, or other non-standard orientations.
CAUTION: All (A1) single reduction gear drive selections Due to the narrow centers dimensions (distance between H.S. shaft centerline and L.S. shaft centerline) associated with single
reduction gear drives, check for possible interference of H.S. shaft and H.S. shaft accessories with L.S. shaft and L.S. shaft accessories.

Type A Assemblies
Standard Assemblies

Other Available Assemblies

SHAFT
GUARD

LOWSPEED
SHAFT
SHAFT
GUARD

HIGHSPEED
SHAFT

OUTBOARD
BEARING

Type AR Assemblies

Type ARJ Assemblies

(Viewed from H.S. end)


Double and Triple Reduction

(Viewed from H.S. end)


Double and Triple Reduction
HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

LOW-SPEED SHAFT

Quadruple Reduction

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

SHRINK DISC

HIGH-SPEED
SHAFT

SHRINK DISC

Quadruple Reduction

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

Type AXV Assemblies

Rotations

(Viewed from H.S. end)


HIGH-SPEED
SHAFT

LOW-SPEED
SHAFT

Single & Triple Reduction


A, AR, ARJ, AXV Gear Drives

16 (131-110)

Double & Quadruple Reduction


A, AR, ARJ, AXV Gear Drives

Rexnord 2014

Horsepower & Torque Ratings/Single Reduction


Horsepower Ratings
Type A Parallel Shaft
HighNominal
Speed
Ratios
Shaft RPM
3%

1750

1430

1170

Drive Size

Approx.
Low-Speed
Shaft RPM

305

325

345

365

385

405

425

445

465

485

505

525

1.84

950

579

688

1082

1375

1785

2893

4503

5093

7437

10689

13594

18755

2.03

860

568

661

1040

1272

1631

2748

3822

4471

6843

9659

12051

17817

2.25

780

517

609

958

1166

1768

2459

3917

4248

6545

9712

12034

17712

2.49

700

491

582

917

1114

1533

2238

3584

3660

5530

9511

12090

16869

2.76

640

465

530

834

1009

1443

2170

3094

3845

5446

8590

11254

14074

3.05

575

414

503

792

956

1314

1958

2913

3653

4543

7831

9472

12831

3.38

520

379

451

709

903

1263

2073

2731

3208

4276

7516

8842

12514

3.74

470

362

424

668

797

1160

1873

2549

2965

4008

7366

9547

11731

4.13

420

328

398

531

744

1046

1506

2219

2780

3475

6048

8355

11569

4.57

380

276

370

494

691

960

1396

1991

2505

3670

5848

7500

10435

5.06

350

217

318

498

653

802

1149

1673

2244

3319

5242

7285

9247

5.60

310

193

293

444

608

1.84

780

502

597

906

1194

1549

2511

3910

4422

6457

9280

11802

16283

2.03

700

493

574

903

1104

1416

2386

3318

3882

5941

8386

10462

15468

2.25

640

449

529

832

1013

1535

2135

3400

3688

5682

8432

10448

15377

2.49

575

426

506

796

967

1331

1943

3112

3177

4801

8257

10496

14646

2.76

520

404

460

724

876

1253

1884

2686

3338

4728

7457

9770

12219

3.05

470

359

437

673

830

1141

1700

2529

3171

3944

6799

8224

11140

3.38

420

329

391

616

784

1096

1773

2371

2785

3712

6526

7676

10864

3.74

380

315

368

580

692

1007

1585

2213

2574

3480

6395

8288

10185

4.13

350

285

345

461

646

864

1230

1814

2414

3017

5251

7253

10044

4.57

310

229

321

428

600

798

1144

1627

2175

3186

5077

6511

9060

5.06

280

180

265

415

567

668

949

1367

1833

2882

4433

5953

7556

5.60

255

160

243

370

518

1.84

640

436

519

741

1037

1346

2182

3397

3842

5611

8064

10255

14149

2.03

575

429

499

741

959

1231

2073

2883

3373

5162

7287

9091

13441

2.25

520

390

459

723

880

1334

1855

2955

3205

4938

7327

9079

13362

2.49

470

371

439

691

840

1157

1688

2704

2761

4172

7175

9120

12727

2.76

420

351

400

629

761

1088

1637

2334

2901

4108

6480

8490

10618

3.05

380

312

380

552

721

991

1477

2197

2756

3427

5908

7146

9680

3.38

350

286

340

535

681

953

1450

2060

2420

3226

5670

6670

9441

3.74

310

272

320

504

601

875

1306

1886

2237

3024

5486

7202

8850

4.13

280

239

300

401

561

720

1024

1493

2097

2621

4563

6303

8375

4.57

255

190

271

372

521

664

954

1349

1890

2769

4299

5638

7504

5.06

230

149

220

345

485

555

790

1141

1511

2504

3627

4871

6182

5.60

210

132

201

307

431

Gear drives at 1750 RPM require jet lubrication and special labyrinth seals; gear drives at 1430 RPM require jet lubrication, refer to Factory.

Rexnord 2014

(131-110) 17

Horsepower & Torque Ratings/Single Reduction


Torque Ratings
Type A Parallel Shaft
HighNominal
Speed
Ratios
Shaft RPM
3%

1750

1430

1170

Approx.
Low-Speed
Shaft RPM

305

325

345

365

385

405

425

445

465

485

505

525

1.84

950

39.0

46.7

73.4

90.0

121

187

296

333

482

696

912

1249

2.03

860

41.8

48.5

76.4

94.0

121

198

282

330

503

714

893

1317

2.25

780

42.8

49.6

78.0

97.0

141

203

317

338

525

783

1003

1457

2.49

700

43.7

51.4

81.0

99.0

140

201

312

333

488

839

1088

1488

2.76

640

45.6

53.4

82.6

101

146

214

314

388

526

859

1096

1436

3.05

575

46.6

55.3

87.0

105

147

211

315

395

500

846

1068

1386

3.38

520

46.4

55.4

87.1

107

149

243

328

401

510

917

1091

1464

3.74

470

48.4

56.3

88.7

109

153

243

334

400

529

967

1267

1520

4.13

420

48.1

58.3

79.2

111

155

220

336

407

529

914

1289

1692

4.57

380

45.0

60.3

82.1

115

154

221

328

399

586

962

1267

1653

5.06

350

39.6

59.5

92.2

119

140

199

301

415

574

944

1349

1602

5.60

310

38.9

60.3

89.8

121

1.84

780

41.3

49.6

75.2

95.0

128

199

315

354

512

740

969

1327

2.03

700

44.4

51.6

81.2

99.0

129

210

299

351

535

758

949

1399

2.25

640

45.5

52.7

82.9

103

149

216

337

359

558

831

1066

1548

2.49

575

46.4

54.7

86.1

105

148

214

332

354

518

891

1156

1581

2.76

520

48.5

56.7

87.7

108

155

227

334

412

559

913

1165

1525

3.05

470

49.4

58.8

90.5

112

157

225

334

419

531

899

1135

1472

3.38

420

49.3

58.8

92.6

114

159

254

348

426

542

974

1159

1556

3.74

380

51.5

59.8

94.2

116

163

251

355

425

562

1028

1346

1615

4.13

350

51.2

61.8

84.1

118

157

220

336

432

562

972

1369

1798

4.57

310

45.7

64.1

87.0

122

157

222

328

424

623

1022

1346

1756

5.06

280

40.2

60.7

94.0

127

143

201

301

415

609

976

1349

1602

5.60

255

39.5

61.2

91.5

126

Drive Size

1.84

640

43.9

52.7

75.2

101

136

211

334

376

544

786

1029

1409

2.03

575

47.2

54.8

81.4

105

137

223

318

372

568

805

1008

1486

2.25

520

48.3

55.9

88.0

110

159

229

358

381

592

883

1132

1645

2.49

470

49.4

58.0

91.3

112

158

227

353

376

550

947

1228

1679

2.76

420

51.4

60.3

93.1

114

165

241

355

437

594

969

1237

1620

3.05

380

52.5

62.5

90.7

119

166

239

355

445

564

954

1206

1564

3.38

350

52.4

62.5

98.3

121

169

254

370

452

575

1035

1231

1652

3.74

310

54.4

63.5

100

123

173

253

370

452

597

1077

1430

1716

4.13

280

52.5

65.7

89.5

125

160

224

338

459

597

1032

1455

1832

4.57

255

46.4

66.1

92.4

129

160

226

332

451

662

1058

1425

1778

5.06

230

40.7

61.6

95.5

132

145

205

307

418

647

976

1349

1602

5.60

210

39.8

61.8

92.8

129

Pound-inches at low-speed shaft multiply values listed by 1000.


Gear drives at 1750 RPM require jet lubrication and special labyrinth seals; gear drives at 1430 RPM require jet lubrication, refer to Factory.

18 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Single Reduction


Horsepower Ratings
Type A Parallel Shaft
HighSpeed
Shaft RPM

870

720

580

Nominal
Approx.
Ratios Low-Speed
3%
Shaft RPM

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

1.84

470

324

389

551

821

1094

1773

2761

3123

4560

6554

8335

11499

2.03

430

324

389

551

780

1000

1685

2343

2741

4196

5922

7388

10924

2.25

390

317

373

551

715

1084

1508

2401

2605

4013

5955

7379

10860

2.49

350

301

357

551

683

940

1372

2198

2244

3391

5831

7412

10343

2.76

320

282

325

511

618

885

1331

1897

2357

3339

5266

6900

8629

3.05

290

250

308

422

586

806

1201

1786

2240

2785

4801

5808

7867

3.38

260

226

276

435

553

774

1108

1609

1967

2622

4319

5421

7672

3.74

235

206

260

408

489

685

997

1436

1818

2458

4080

5853

7193

4.13

210

181

241

326

456

546

779

1140

1705

2130

3480

5067

6228

4.57

190

143

205

298

424

503

725

1028

1536

2094

3203

4193

5580

5.06

175

112

166

261

368

420

600

868

1153

1899

2724

3636

4597

5.60

155

99.5

152

232

327

1.84

390

268

322

456

679

958

1553

2303

2715

3994

5741

7301

10072

2.03

350

268

322

456

679

876

1476

2052

2401

3675

5188

6472

9568

2.25

320

268

322

456

626

949

1321

2004

2281

3515

5216

6463

9512

2.49

290

264

313

456

598

823

1202

1902

1966

2970

5108

6493

9060

2.76

260

236

285

425

542

775

1140

1659

2065

2925

4613

6044

7559

3.05

235

209

258

354

513

681

1052

1517

1962

2440

4206

5087

6891

3.38

210

189

242

371

485

665

930

1353

1723

2296

3574

4748

6721

3.74

190

172

228

342

428

573

836

1206

1593

2153

3386

4878

6300

4.13

175

151

202

281

400

456

652

956

1442

1866

2922

4228

5154

4.57

155

120

171

249

359

420

607

861

1326

1762

2701

3523

4629

5.06

140

93.6

138

218

307

351

501

726

967

1596

2293

3065

3843

5.60

130

82.9

126

193

273

1.84

320

216

259

367

547

824

1335

1855

2187

3433

4819

6013

8658

2.03

290

216

259

367

547

753

1268

1764

2064

3159

4459

5563

8225

2.25

260

216

259

367

538

813

1135

1647

1961

3012

4483

5555

8157

2.49

235

215

259

367

514

708

1033

1561

1689

2553

4382

5581

7681

2.76

210

192

243

343

466

660

932

1358

1740

2514

3965

5195

6497

3.05

190

170

210

289

441

555

859

1241

1639

2097

3615

4373

5923

3.38

175

153

208

303

417

542

759

1106

1434

1974

2933

4081

5777

3.74

155

139

192

278

368

466

681

984

1318

1850

2785

3998

5327

4.13

140

122

164

229

343

371

531

779

1178

1604

2397

3473

4226

4.57

130

97.0

139

202

292

341

494

701

1083

1442

2213

2890

3808

5.06

115

75.8

112

177

250

285

408

591

788

1304

1877

2510

3156

5.60

105

67.2

103

157

222

Gear drives at 1750 RPM require jet lubrication and special labyrinth seals; gear drives at 1430 RPM require jet lubrication, refer to Factory.

Rexnord 2014

(131-110) 19

Horsepower & Torque Ratings/Single Reduction


Torque Ratings
Type A Parallel Shaft
HighSpeed
Shaft RPM

870

720

580

Nominal
Approx.
Ratios Low-Speed
3%
Shaft RPM

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

1.84

470

43.9

53.1

75.2

107

149

231

365

411

594

859

1125

1540

2.03

430

48.0

57.5

81.4

115

149

244

347

407

621

880

1101

1624

2.25

390

52.8

61.1

90.2

120

174

251

391

417

647

965

1237

1798

2.49

350

53.9

63.5

97.9

122

172

248

385

411

602

1034

1342

1835

2.76

320

55.6

65.9

102

125

180

263

388

478

649

1059

1352

1770

3.05

290

56.6

68.1

93.3

130

182

261

388

487

617

1043

1318

1709

3.38

260

55.6

68.2

107

132

184

261

388

494

629

1060

1346

1806

3.74

235

55.4

69.4

109

135

182

260

379

494

653

1078

1563

1875

4.13

210

53.4

71.0

97.8

137

163

229

347

502

653

1058

1573

1832

4.57

190

46.9

67.2

99.6

142

163

231

340

493

673

1060

1425

1778

5.06

175

41.1

62.5

97.2

135

148

209

314

429

660

986

1354

1602

5.60

155

40.3

62.9

94.3

131

1.84

390

43.8

53.1

75.2

107

158

245

368

432

629

909

1191

1630

2.03

350

48.0

57.5

81.4

121

158

258

368

431

657

932

1166

1718

2.25

320

53.9

63.7

90.2

127

184

265

395

441

685

1021

1310

1902

2.49

290

57.1

67.2

97.9

130

182

263

403

435

637

1095

1420

1942

2.76

260

56.2

69.8

102

132

191

273

410

506

687

1121

1431

1874

3.05

235

57.1

68.9

94.6

137

186

276

398

515

653

1104

1395

1809

3.38

210

56.2

72.2

111

140

191

264

395

523

665

1060

1424

1911

3.74

190

55.9

73.6

110

142

184

263

384

523

691

1081

1574

1984

4.13

175

53.9

71.9

102

145

165

232

351

513

691

1074

1585

1832

4.57

155

47.6

67.8

101

145

164

234

344

514

684

1080

1446

1782

5.06

140

41.5

62.8

98.1

136

149

211

318

434

670

1003

1379

1618

5.60

130

40.6

63.0

94.8

132

1.84

320

43.9

53.0

75.1

107

168

261

368

432

671

947

1217

1740

2.03

290

48.0

57.4

81.3

121

169

275

392

460

701

994

1244

1834

2.25

260

54.0

63.6

90.1

135

195

283

403

471

729

1090

1397

2025

2.49

235

57.8

69.1

97.8

138

195

281

411

464

679

1166

1516

2044

2.76

210

56.8

73.9

102

141

202

277

416

529

733

1196

1527

2000

3.05

190

57.7

69.6

95.8

146

188

280

404

534

697

1178

1488

1930

3.38

175

56.5

77.1

112

149

193

268

400

541

710

1080

1520

2039

3.74

155

56.1

76.9

111

152

186

266

389

537

737

1103

1601

2083

4.13

140

54.0

72.4

103

154

166

234

355

520

737

1094

1617

1865

4.57

130

47.8

68.4

101

146

165

236

348

521

695

1099

1473

1820

5.06

115

41.8

63.3

98.9

138

150

213

321

439

680

1019

1402

1650

5.60

105

40.9

63.9

95.8

134

Pound-inches at low-speed shaft multiply values listed by 1000.

20 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Double Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
Approx.
HighLowSpeed Nominal
Ratios
Speed
Shaft
4%
Shaft
RPM
RPM

1750

1430

1170

5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74

310
280
255
230
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
255
230
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
45
40
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
45
40
37
34

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

159
159
159
159
135
120
119
113
91.8
94.4
75.8
70.6
59.9
56.2
51.1
45.4
36.9
36.4

130
130
130
130
111
98.7
97.5
92.0
75.4
77.2
62.2
58.3
49.1
46.3
41.8
37.2
30.4
29.8

106
106
106
106
91.4
81.3
79.8
75.3
62.0
63.1
51.1
48.1
40.3
38.2
34.3
30.5
25.0
24.5

242
228
214
215
175
179
154
146
137
136
110
109
88.3
87.0
72.7
66.5
61.7
56.5

210
198
186
187
152
148
127
127
119
112
90.7
89.2
72.5
71.9
59.6
54.5
50.6
46.3

182
172
162
162
132
122
104
104
103
91.7
74.5
73.2
59.5
59.3
48.8
44.7
41.4
37.9

408
389
348
324
308
275
216
216
216
191
168
159
140
131
119
106
94.4
88.5

348
337
303
282
254
227
179
179
178
157
138
131
115
109
97.7
87.0
77.9
72.5

284
284
263
239
210
187
149
149
146
129
113
107
94.2
89.8
80.2
71.4
64.3
59.4

505
455
429
402
375
351
338
304
286
268
253
201
201
191
164
157
136
121

439
395
372
349
325
305
288
264
249
233
220
167
167
157
134
130
111
98.9

381
343
323
304
283
260
236
229
216
197
187
138
138
129
110
106
91.3
81.1

628
624
577
561
512
484
426
401
384
322
309
279
267
214

513
510
485
458
419
395
348
328
314
263
252
228
218
175

423
417
397
375
343
323
285
268
257
216
206
186
178
143

919
920
883
815
769
716
669
632
550
524
441
419
370
323

1215
1215
1215
1054
1054
924
924
896
781
739
592
633
579
463

1668
1496
1442
1365
1296
1226
1099
1039
991
937
852
805
729
635

2453
2323
2179
1965
1843
1740
1632
1433
1404
1237
1186
1045
1101
999

3688
3533
3363
3074
2925
2625
2498
2346
2232
1975
1882
1661
1609
1448

3202
3067
2920
2669
2540
2279
2169
2036
1937
1715
1634
1442
1397
1231

2782
2665
2537
2319
2207
1980
1884
1770
1684
1490
1420
1253
1194
1014

5080
4766
5004
4240
4386
3899
3756
3336
3240
2742
2876
2577
2365
2204

4411
4137
4345
3681
3808
3385
3261
2896
2813
2381
2497
2237
1972
1817

3833
3595
3775
3198
3309
2942
2834
2516
2445
2069
2170
1944
1626
1498

6976
6676
6036
5777
5087
4807
4231
4436
4151
3831
3439
3242
2973
2690

6057
5796
5240
5015
4417
4174
3673
3851
3604
3326
2985
2776
2462
2219

5263
5037
4554
4358
3838
3627
3192
3347
3132
2890
2594
2293
2031
1829

7245
6965
6394
6027
5385
5364
5087
4807
4231
4151
3439
3439
3242
3030

6290
6047
5551
5232
4675
4657
4416
4173
3673
3604
2985
2985
2758
2503

5466
5254
4824
4547
4062
4047
3838
3626
3192
3132
2594
2594
2277
2066

9010
8190
7868
7142
7001
6179
6055
5373
5264
4724
4625
4307
4014
3819

7822
7110
6831
6201
6078
5364
5257
4665
4570
4101
4016
3739
3485
3316

6797
6178
5935
5388
5281
4662
4568
4054
3971
3564
3489
3249
3028
2790

9217
8948
7922
7766
6806
6706
6292
5844
5469
5190
4760
4474
4230
3956

8002
7768
6878
6742
5909
5822
5462
5073
4748
4506
4133
3884
3672
3435

6953
6750
5977
5859
5135
5059
4746
4408
4126
3916
3591
3375
3191
2917

11022
10135
9559
8875
8273
7987
7453
6779
6403
6019
5575
5050
4805
4295

9569
8799
8299
7705
7183
6934
6470
5886
5559
5226
4840
4385
4171
3545

8315
7646
7212
6695
6241
6026
5623
5114
4831
4541
4206
3810
3625
2928

15272
14232
14541
11969
12331
11974
10900
10316
9944
8148
8401
8090
7645
6597

13259
12356
12624
10391
10705
10395
9463
8956
8634
7074
7293
7023
6637
5447

11521
10737
10970
9029
9302
9033
8223
7783
7502
6147
6338
6103
5673
4500

Consult Factory

798
798
767
708
667
621
552
527
458
431
366
345
304
266

1055
1055
1055
915
915
803
790
732
653
604
484
517
473
379

1448
1299
1252
1185
1125
1064
954
902
860
813
740
699
633
522

2130
2017
1892
1706
1600
1511
1417
1244
1219
1074
1029
907
956
868

Consult Factory

694
694
666
615
580
516
456
435
381
355
304
283
250
218

917
917
917
795
779
675
646
599
534
494
396
423
387
310

1258
1129
1088
1030
978
925
829
784
748
707
643
607
550
429

1851
1753
1644
1482
1390
1313
1231
1081
1060
933
895
788
798
722

Consult Factory

For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

305

325

345

365

385

Availability of Types A / AR / AXV Double and Triple Reduction


405
425
445
465
485
505
525

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

535

545

555

565

585

X
X

X
X

Rexnord 2014

(131-110) 21

Horsepower & Torque Ratings/Double Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
Approx.
HighLowSpeed Nominal
Ratios
Speed
Shaft
4%
Shaft
RPM
RPM

1750

1430

1170

5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74

310
280
255
230
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
255
230
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
45
40
210
190
170
155
140
125
115
100
90
84
75
68
60
56
50
45
40
37
34

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

35.4
38.7
42.4
47.2
44.8
44.0
47.3
49.9
45.4
50.7
45.6
48.2
45.8
45.2
46.0
45.1
41.5
45.2

35.4
38.7
42.5
47.2
45.1
44.3
47.4
49.7
45.6
50.8
45.8
48.8
45.9
45.6
46.0
45.2
41.8
45.2

35.3
38.5
42.3
47.0
45.4
44.6
47.4
49.7
45.8
50.7
46.0
49.2
46.1
46.0
46.2
45.3
42.0
45.5

55.2
56.2
58.2
65.1
60.8
68.4
63.4
65.0
67.2
74.4
69.0
74.9
69.7
73.0
70.0
70.4
70.1
70.6

58.6
59.7
61.9
69.3
64.7
69.2
64.0
69.2
71.5
74.9
69.7
75.0
70.0
73.8
70.2
70.6
70.4
70.8

62.1
63.4
65.9
73.4
68.6
69.7
64.1
69.2
75.6
75.0
69.9
75.2
70.2
74.4
70.3
70.7
70.4
70.8

92.3
95.1
95.6
99.2
105
102
92.0
99.4
112
110
108
111
109
107
109
106
104
106

96.4
101
102
106
106
103
93.3
101
113
111
108
112
109
109
109
106
105
106

96.1
104
108
109
107
104
94.9
103
113
111
108
111
109
110
109
106
106
106

112
116
120
125
128
131
136
141
145
149
154
139
152
161
152
160
153
148

119
124
127
133
136
139
142
150
155
159
164
142
155
162
152
162
152
148

126
131
135
141
144
145
142
159
164
164
170
143
156
163
152
162
153
149

133
139
143
157
151
160
154
163
169
166
173
168
174
152

132
139
147
156
151
160
154
163
169
166
172
168
174
152

133
139
147
157
151
160
154
163
169
167
172
168
174
152

185
201
213
222
226
237
240
250
238
255
240
257
246
235

245
272
297
286
313
309
338
378
352
384
335
390
391
340

339
352
366
377
387
397
417
428
440
451
474
486
479
484

486
499
518
538
558
567
589
597
602
612
636
647
715
701

727
787
806
844
864
904
926
954
977
995
1032
1055
1112
1095

773
836
857
897
918
961
984
1013
1037
1058
1097
1121
1182
1139

821
888
910
952
975
1020
1045
1077
1102
1123
1165
1190
1234
1147

1042
1070
1208
1157
1287
1330
1396
1441
1493
1376
1540
1617
1625
1649

1107
1136
1283
1229
1368
1413
1483
1531
1586
1463
1636
1718
1658
1663

1176
1207
1363
1305
1452
1501
1576
1626
1685
1553
1738
1824
1671
1676

1356
1406
1452
1505
1598
1672
1640
1741
1782
1856
1886
2006
2087
2045

1441
1494
1543
1599
1698
1777
1742
1850
1893
1972
2003
2102
2115
2065

1530
1587
1638
1699
1803
1887
1850
1965
2011
2094
2127
2122
2133
2080

1487
1540
1623
1649
1648
1768
1813
1889
1861
2013
1931
2130
2253
2277

1580
1636
1725
1752
1751
1879
1926
2007
1977
2139
2052
2263
2345
2302

1678
1737
1832
1861
1859
1996
2046
2131
2099
2272
2179
2403
2376
2322

1797
1778
1941
1918
2055
2060
2206
2185
2339
2381
2547
2655
2693
2803

1910
1889
2063
2038
2183
2188
2344
2322
2486
2529
2707
2821
2861
2978

2028
2007
2190
2164
2318
2324
2489
2466
2640
2687
2874
2996
3039
3062

1872
1967
1990
2112
2122
2264
2349
2406
2491
2578
2687
2754
2834
2955

1989
2090
2114
2244
2254
2405
2495
2556
2646
2739
2855
2926
3011
3140

2112
2220
2246
2383
2395
2554
2650
2715
2811
2909
3032
3108
3198
3259

2218
2337
2391
2543
2575
2674
2710
2876
2951
3025
3013
3172
3305
3289

2357
2483
2540
2702
2736
2841
2879
3056
3135
3214
3201
3371
3511
3322

2503
2638
2698
2870
2905
3018
3059
3245
3330
3413
3400
3580
3729
3354

3178
3223
3589
3349
3760
4003
4120
4275
4312
4052
4553
4807
4920
5105

3377
3424
3813
3558
3995
4252
4377
4542
4581
4305
4837
5106
5227
5158

3586
3637
4050
3778
4243
4516
4649
4824
4865
4572
5138
5424
5460
5209

Consult Factory

197
213
227
236
239
252
242
255
242
257
244
259
248
237

260
289
316
304
332
329
354
378
360
384
335
389
390
341

360
374
389
401
411
421
443
455
467
479
504
517
509
487

517
530
550
571
593
603
626
634
640
651
675
687
759
746

Consult Factory

209
226
241
251
254
255
245
257
246
259
248
260
249
237

276
307
335
323
346
338
353
378
360
384
335
389
390
340

383
397
414
425
437
448
471
483
496
509
536
548
541
489

549
563
584
606
630
640
664
673
680
691
718
729
775
758

Consult Factory

Pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

305

325

345

365

385

Availability of Types A / AR / AXV Double and Triple Reduction


405
425
445
465
485
505
525

X
X
X

X
X
X

22 (131-110)

X
X
X

X
X
X

X
X
X

X
X
X

535

545

555

565

585

X
X

X
X

Rexnord 2014

Horsepower & Torque Ratings/Double Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
Approx.
HighLowSpeed Nominal
Ratios
Speed
Shaft
4%
Shaft
RPM
RPM

870

720

580

5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74

155
140
130
115
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
130
115
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
22
21
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
22
21
18
17

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

79.1
79.1
79.1
79.1
68.4
60.8
59.3
56.0
46.3
46.9
38.1
36.1
30.1
28.6
25.6
22.7
18.8
18.2

65.4
65.4
65.4
65.4
56.8
50.5
49.1
46.3
38.4
38.9
31.6
30.1
24.9
23.8
21.2
18.8
15.6
15.1

52.7
52.7
52.7
52.7
45.9
40.8
39.5
37.3
31.0
31.3
25.5
24.3
20.1
19.2
17.1
15.2
12.6
12.2

137
137
131
122
99.4
91.1
77.2
77.2
77.2
68.5
55.6
54.7
44.4
44.6
36.4
33.3
30.9
28.3

113
113
109
102
82.6
75.6
63.9
63.9
63.9
56.8
46.1
45.3
36.8
37.1
30.2
27.6
25.6
23.4

91.1
91.1
88.2
82.2
66.8
61.1
51.5
51.5
51.5
45.9
37.2
36.6
29.7
30.0
24.3
22.3
20.6
18.9

211
211
202
179
157
140
112
112
109
96.6
84.7
80.2
70.3
67.6
59.8
53.2
48.3
44.3

175
175
168
149
131
117
93.6
93.6
90.6
80.1
70.3
66.5
58.3
56.2
49.6
44.1
40.2
36.7

141
141
136
121
106
94.3
75.9
75.9
73.2
64.7
56.7
53.7
47.0
45.5
40.0
35.6
32.5
29.6

310
279
263
247
219
195
175
175
168
146
140
104
104
96.0
82.3
79.4
68.1
60.5

261
244
230
212
182
162
145
145
139
121
116
86.8
86.8
79.6
68.3
65.8
56.4
50.1

210
206
197
172
148
131
117
117
112
97.5
93.9
70.4
70.4
64.2
55.1
53.1
45.5
40.4

317
310
295
279
255
240
212
199
191
160
153
139
133
106

263
257
244
231
211
199
175
165
158
133
127
115
110
87.9

211
207
197
186
170
160
141
133
127
107
102
92.4
88.4
70.8

564
552
529
468
447
388
342
326
288
266
229
212
186
163

745
716
687
604
580
502
480
445
397
367
295
315
288
230

1023
917
884
837
795
751
674
637
608
574
513
479
441
321

1504
1424
1336
1205
1130
1067
1001
878
861
758
727
641
598
541

2261
2166
2062
1885
1794
1609
1532
1438
1368
1211
1121
970
896
760

1981
1897
1806
1651
1571
1410
1342
1239
1175
1011
933
807
744
631

1702
1631
1553
1419
1350
1180
1119
1004
952
819
755
652
602
510

3115
2922
3068
2599
2689
2391
2303
2045
1954
1664
1710
1466
1220
1123

2728
2559
2688
2277
2356
2094
1974
1753
1617
1398
1423
1220
1014
933

2345
2200
2310
1957
1959
1787
1590
1421
1303
1143
1153
987
819
753

4277
4093
3701
3542
3119
2947
2594
2668
2545
2182
2108
1723
1524
1372

3747
3585
3242
3102
2732
2582
2272
2227
2229
1818
1811
1433
1267
1141

3220
3082
2786
2667
2348
2219
1953
1808
1862
1474
1467
1160
1025
923

4442
4270
3920
3695
3302
3289
3119
2947
2594
2545
2108
2108
1711
1551

3891
3741
3434
3237
2892
2881
2732
2582
2272
2230
1847
1780
1424
1290

3345
3215
2952
2782
2486
2476
2348
2219
1953
1830
1583
1442
1153
1044

5524
5021
4824
4379
4292
3788
3712
3294
3227
2812
2671
2450
2265
2074

4839
4398
4225
3836
3760
3318
3252
2845
2706
2327
2211
2028
1875
1717

4159
3781
3494
3297
3200
2760
2628
2292
2180
1874
1781
1633
1510
1383

5651
5486
4857
4761
4173
4112
3857
3583
3353
3182
2918
2743
2593
2197

4950
4806
4255
4171
3655
3602
3379
3138
2937
2787
2556
2389
2202
1831

4255
4131
3657
3585
3020
3020
2904
2697
2525
2385
2197
1940
1788
1486

6758
6214
5861
5441
5073
4897
4569
4157
3926
3691
3418
3056
2802
2204

5919
5443
5134
4766
4443
4289
4003
3585
3429
3157
2944
2549
2336
1837

5088
4679
4413
4097
3819
3602
3440
2888
2762
2558
2391
2070
1897
1491

9020
8726
8916
7338
7560
7341
6683
6325
5909
4996
4797
4560
4219
3390

7465
7465
7465
6428
6622
6431
5541
5274
4890
4376
3970
3774
3491
2827

6013
6013
6013
5525
5449
5192
4463
4248
3939
3661
3198
3040
2812
2295

Consult Factory

473
457
438
390
370
322
284
271
241
221
191
176
155
135

619
592
569
500
480
415
398
369
329
304
244
260
238
191

896
804
775
733
696
658
590
558
532
498
429
398
365
267

1317
1248
1170
1055
990
934
876
769
754
664
616
561
497
449

Consult Factory

381
368
353
316
298
261
230
219
196
178
155
142
125
109

499
477
458
403
386
334
320
297
265
245
196
210
192
154

770
691
666
630
598
566
507
469
450
402
349
322
294
215

1132
1072
1006
907
851
803
753
661
647
566
501
455
402
363

Consult Factory

For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

305

325

345

365

385

Availability of Types A / AR / AXV Double and Triple Reduction


405
425
445
465
485
505
525

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

535

545

555

565

585

X
X

X
X

Rexnord 2014

(131-110) 23

Horsepower & Torque Ratings/Double Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
Approx.
HighLowSpeed Nominal
Ratios
Speed
Shaft
4%
Shaft
RPM
RPM

870

720

580

5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74

155
140
130
115
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
130
115
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
22
21
105
95
85
77
70
62
55
50
45
42
38
34
31
28
25
22
21
18
17

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

35.4
38.7
42.5
47.2
45.7
44.8
47.4
49.7
46.0
50.7
46.1
49.6
46.3
46.3
46.3
45.4
42.5
45.4

35.4
38.6
42.4
47.2
45.8
45.0
47.4
49.7
46.1
50.8
46.2
50.0
46.3
46.5
46.4
45.4
42.6
45.5

35.4
38.7
42.4
47.2
46.0
45.1
47.3
49.7
46.2
50.8
46.3
50.1
46.4
46.6
46.4
45.6
42.7
45.7

62.9
67.9
71.6
74.3
69.5
70.0
64.0
69.1
76.2
75.3
70.2
75.6
70.5
75.2
70.5
70.9
70.6
71.1

62.6
67.7
72.0
75.1
69.8
70.2
64.0
69.1
76.2
75.5
70.3
75.7
70.6
75.6
70.7
71.0
70.7
71.0

62.7
67.8
72.4
75.1
70.1
70.4
64.0
69.2
76.3
75.7
70.5
75.9
70.7
75.9
70.6
71.2
70.6
71.2

96.0
104
112
110
108
105
95.9
104
113
112
109
112
110
111
110
107
107
107

96.2
104
112
111
109
106
96.9
105
114
112
110
112
110
112
110
107
107
107

96.3
104
113
112
109
106
97.5
105
114
112
110
113
110
112
110
107
108
107

138
144
148
154
150
146
142
164
171
164
171
145
158
163
153
163
154
149

141
152
156
160
151
147
142
164
171
164
171
146
160
163
154
163
154
149

140
159
166
161
152
147
142
164
171
164
172
147
161
163
154
164
154
149

135
139
147
157
151
160
154
163
169
166
172
169
175
151

135
139
147
157
151
160
154
163
169
167
172
168
174
152

134
139
148
157
151
160
154
163
169
167
172
168
174
152

228
242
257
257
264
258
247
260
250
261
251
262
249
239

302
322
338
330
346
338
353
378
360
384
336
390
391
340

418
434
452
465
477
489
515
528
542
555
575
582
583
492

600
615
639
663
688
700
726
735
743
755
784
798
781
764

897
971
994
1041
1066
1115
1142
1176
1204
1228
1237
1239
1246
1156

950
1027
1052
1102
1128
1181
1209
1225
1250
1238
1244
1246
1250
1159

1013
1096
1123
1175
1203
1226
1252
1232
1257
1245
1250
1249
1255
1163

1285
1319
1490
1426
1587
1640
1722
1777
1811
1680
1842
1850
1686
1690

1360
1396
1577
1510
1680
1736
1783
1841
1811
1706
1852
1860
1693
1696

1451
1490
1682
1611
1735
1839
1783
1852
1811
1731
1863
1868
1698
1700

1672
1734
1791
1857
1970
2062
2022
2107
2198
2126
2325
2144
2152
2098

1770
1835
1895
1965
2085
2183
2140
2125
2326
2141
2414
2155
2162
2109

1889
1958
2022
2097
2225
2329
2284
2142
2412
2155
2427
2166
2171
2117

1833
1899
2002
2033
2032
2181
2236
2329
2294
2483
2381
2626
2392
2344

1941
2010
2119
2152
2151
2309
2366
2466
2428
2628
2521
2680
2405
2356

2071
2145
2262
2296
2295
2463
2524
2631
2591
2678
2683
2695
2417
2367

2217
2193
2394
2366
2534
2540
2720
2695
2885
2851
2959
3038
3057
3061

2346
2321
2534
2504
2682
2688
2879
2812
2923
2851
2960
3038
3058
3063

2503
2477
2601
2672
2834
2776
2889
2812
2923
2850
2960
3037
3057
3062

2309
2426
2454
2604
2617
2792
2896
2968
3072
3179
3313
3397
3495
3301

2443
2568
2598
2757
2770
2955
3066
3140
3251
3365
3507
3575
3586
3324

2607
2740
2772
2941
2841
3075
3271
3351
3470
3574
3742
3603
3615
3349

2736
2883
2949
3136
3176
3298
3342
3548
3639
3731
3716
3861
3876
3395

2896
3051
3121
3320
3361
3491
3538
3697
3840
3856
3867
3892
3905
3419

3090
3256
3330
3543
3586
3639
3775
3697
3840
3879
3899
3923
3937
3445

3776
3975
4426
4130
4637
4936
5081
5272
5154
4997
5230
5450
5461
5277

3776
4109
4478
4371
4908
5225
5091
5312
5153
5289
5230
5450
5460
5317

3776
4108
4478
4664
5014
5237
5090
5311
5153
5493
5230
5450
5460
5359

Consult Factory

231
242
257
258
264
259
247
261
253
262
253
263
251
239

303
322
338
330
346
338
354
378
360
384
335
389
390
341

443
460
479
492
505
518
544
558
574
582
581
584
583
495

634
651
676
702
729
740
768
778
786
799
803
844
784
766

Consult Factory

231
242
257
260
264
261
249
261
255
262
255
263
251
239

303
322
338
330
346
337
353
378
360
384
335
390
391
341

472
490
511
525
538
553
581
583
602
583
586
587
583
495

677
694
721
749
778
790
820
830
837
845
811
849
787
769

Consult Factory

Pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

305

325

345

365

385

Availability of Types A / AR / AXV Double and Triple Reduction


405
425
445
465
485
505
525

X
X
X

X
X
X

24 (131-110)

X
X
X

X
X
X

X
X
X

X
X
X

535

545

555

565

585

X
X

X
X

Rexnord 2014

Horsepower & Torque Ratings/Triple Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
Drive Size

HighNominal Approx.
Speed
Ratios Low-Speed
Shaft RPM 4%
Shaft RPM

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

31.2
29.4
27.6
23.6
22.9
19.5
18.0
15.9
14.7
13.6
12.5
11.1
9.24
8.91
8.01
7.47
6.41
5.99

25.8
24.0
22.6
19.5
18.7
15.9
14.7
13.0
12.0
11.1
10.2
9.09
7.56
7.28
6.54
6.11
5.24
4.89

21.3
19.7
18.5
16.1
15.3
13.0
12.1
10.6
9.86
9.12
8.38
7.44
6.20
5.96
5.36
5.00
4.29
4.01

49.8
49.9
40.9
34.4
34.7
32.4
25.5
24.3
18.2
18.2
17.8
16.3
15.1
13.8
8.48
8.48
8.48
8.48

40.8
41.0
33.5
28.4
28.4
26.6
21.1
19.9
15.0
15.0
14.6
13.3
12.4
11.3
6.97
6.97
6.97
6.97

33.4
33.7
27.4
23.5
23.3
21.8
17.4
16.3
12.4
12.4
11.9
10.9
10.1
9.25
5.73
5.73
5.73
5.73

66.4
66.4
54.1
54.1
52.0
49.2
43.1
38.8
34.0
33.0
28.9
25.7
23.5
21.4
19.7
17.5
16.1
14.6

55.1
55.1
44.8
44.8
42.6
40.3
35.3
31.7
27.8
27.0
23.6
21.0
19.3
17.5
16.1
14.3
13.2
11.9

45.6
45.6
37.1
37.1
34.9
33.0
28.9
26.0
22.8
22.1
19.3
17.2
15.8
14.3
13.2
11.7
10.8
9.74

95.6
95.6
95.6
88.8
76.2
67.7
61.4
54.1
50.5
40.4
39.8
35.3
32.9
29.2
26.5
23.5
20.5
19.9

79.3
79.3
79.3
72.7
62.4
55.4
50.2
44.8
41.3
33.3
32.5
28.9
26.9
23.9
21.7
19.2
16.9
16.3

65.7
65.7
65.7
59.6
51.1
45.4
41.1
37.1
33.8
27.5
26.6
23.7
22.0
19.5
17.7
15.7
13.9
13.3

192
181
158
145
127
120
115
94.3
90.2
81.5
77.2
66.7
62.5
53.6
43.2

157
148
129
119
104
97.7
93.6
77.0
73.7
66.6
63.1
54.5
51.2
43.9
35.3

128
121
106
97.2
85.0
80.0
76.6
63.0
60.3
54.5
51.6
44.6
42.0
36.0
28.9

281
296
255
234
202
186
171
155
142
129
118
90.9
91.9
80.3
68.6
63.1

232
243
210
192
166
152
140
127
117
105
96.7
74.3
75.2
65.7
56.1
51.6

193
199
173
157
137
125
115
104
95.5
86.2
79.2
60.9
61.6
53.8
46.0
42.2

397
354
354
332
292
270
216
231
213
182
146
156
143
120
100
91.4

345
306
293
271
238
221
177
189
174
149
119
127
117
98.5
81.7
74.7

284
251
240
222
195
181
145
155
142
122
97.6
104
95.3
80.9
66.9
61.1

639
606
559
529
494
427
408
358
317
292
266
232
211
196
167
132

555
526
486
438
411
350
335
294
260
239
218
190
173
160
136
108

482
435
402
359
337
287
274
241
214
196
178
156
141
131
112
88.6

908
800
793
698
685
603
569
498
442
400
353
320
270
244
220
204

789
694
688
606
573
502
467
409
364
328
289
277
221
199
180
167

685
603
578
506
471
412
383
335
299
269
237
227
181
163
148
137

1226
1226
1196
1108
1023
877
809
753
695
600
553
479
442
407
376
319

1064
1064
983
911
840
719
664
617
569
492
453
393
362
333
308
261

925
876
808
748
690
591
545
507
467
403
372
322
297
273
252
214

1760
1553
1760
1464
1505
1254
1209
1072
1000
917
844
736
677
559
513
472

1528
1349
1524
1250
1237
1024
988
879
820
752
691
603
555
457
419
386

1328
1172
1254
1023
1016
838
809
721
673
617
567
495
455
374
343
315

2567
2440
2306
2124
1986
1684
1565
1442
1331
1158
1060
838
800
706
623
560

2228
2088
1965
1770
1632
1394
1285
1191
1091
949
869
687
655
578
510
459

1868
1737
1617
1448
1341
1152
1055
978
896
776
713
563
537
474
418
376

2881
2567
2490
2191
2124
1952
1684
1442
1442
1308
1088
1028
995
878
701
669

2502
2228
2162
1842
1765
1604
1394
1191
1191
1073
945
854
815
719
574
548

2174
1868
1813
1507
1444
1318
1152
983
975
880
774
701
668
589
471
449

3112
3084
2832
2470
2232
1993
1895
1701
1617
1391
1321
1176
1100
960
759
698

2666
2557
2314
2018
1824
1628
1548
1390
1321
1136
1080
961
899
784
621
571

2181
2092
1893
1651
1492
1332
1267
1137
1081
930
883
786
735
642
509
468

3212
3212
3112
2843
2660
2465
2289
2149
2049
1790
1705
1454
1331
1161
1069
888

2788
2788
2702
2468
2309
2140
1987
1866
1726
1472
1398
1196
1094
954
878
729

2423
2423
2348
2145
2007
1859
1656
1541
1417
1212
1147
984
900
784
722
600

4119
3870
3656
3246
3105
2631
2376
2222
1970
1825
1705
1503
1413
1306
1038
951

3435
3197
3058
2653
2537
2150
1942
1816
1610
1491
1394
1228
1155
1067
853
781

2811
2616
2502
2170
2076
1759
1589
1486
1317
1220
1140
1005
945
873
702
642

5159
4538
4073
4073
3720
3515
3515
2970
2800
2570
2423
2168
1911
1768
1597
1464

4479
3940
3537
3537
3230
3051
2933
2579
2408
2134
1980
1772
1561
1445
1313
1203

3892
3423
3073
2961
2806
2652
2399
2182
1970
1746
1620
1449
1278
1182
1080
989

1750

1430

1170

75.0
68.0
60.0
56.0
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
60.0
56.0
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4

See page21 for availability of Type A, AR, AXV triple reduction.


For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

Rexnord 2014

(131-110) 25

Horsepower & Torque Ratings/Triple Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
HighApprox.
Speed Nominal
LowRatios
Shaft
Speed
4%
RPM
Shaft RPM

1750

1430

1170

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

75.0
68.0
60.0
56.0
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
60.0
56.0
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
50.0
45.0
40.0
37.0
34.0
30.0
27.0
25.0
22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

42.9
44.0
46.2
42.7
46.4
44.9
46.4
44.8
46.4
45.1
46.4
45.5
42.8
45.6
45.6
45.6
45.6
45.6

43.5
44.0
46.3
43.2
46.4
44.8
46.3
44.8
46.3
45.1
46.3
45.6
42.9
45.6
45.6
45.6
45.6
45.6

43.8
44.1
46.4
43.6
46.4
44.8
46.6
44.7
46.5
45.3
46.5
45.6
43.0
45.6
45.7
45.6
45.6
45.7

70.3
74.9
70.5
65.9
70.6
75.7
67.8
71.0
59.2
63.0
70.7
71.1
70.8
71.1
50.2
55.1
59.2
65.1

70.5
75.3
70.6
66.5
70.7
76.0
68.6
71.1
59.7
63.5
71.0
71.0
71.1
71.2
50.4
55.4
59.6
65.4

70.5
75.6
70.6
67.3
70.9
76.2
69.2
71.2
60.4
64.2
70.7
71.1
70.8
71.3
50.7
55.7
59.8
65.8

92.9
103
92.1
103
110
113
110
113
110
113
110
107
108
107
111
107
109
108

94.3
105
93.4
104
110
113
110
113
110
113
110
107
109
107
111
107
109
107

95.4
106
94.5
105
110
113
110
113
111
113
110
107
109
107
111
107
109
107

131
146
157
163
153
149
154
150
154
143
154
149
155
150
155
150
141
150

133
148
160
163
154
149
154
152
154
144
154
150
155
150
155
150
143
150

135
150
162
163
154
149
154
154
154
145
154
150
155
150
154
150
143
150

154
163
154
166
157
167
173
166
172
168
172
174
174
175
153

154
163
154
167
157
166
172
166
172
168
173
174
175
175
153

153
163
154
166
157
166
173
166
172
168
172
174
175
176
153

226
260
252
261
252
262
262
263
262
264
263
240
251
240
240
241

228
261
254
262
253
262
262
264
264
263
264
240
252
241
240
241

232
261
256
262
256
263
264
264
264
264
264
240
252
241
241
241

336
325
355
384
360
384
334
389
385
384
335
390
392
368
340
340

358
344
360
384
359
385
335
390
384
385
334
388
392
370
340
340

360
345
360
384
360
385
336
391
383
385
335
389
390
371
340
340

528
543
561
576
593
584
603
585
588
588
583
588
583
586
587
497

561
577
597
584
604
585
606
588
591
589
585
590
585
586
585
497

596
583
604
585
605
587
606
589
594
590
584
592
583
586
589
499

726
738
770
782
820
833
839
847
815
851
788
806
772
792
772
776

772
783
817
831
839
848
843
852
821
854
789
854
773
790
773
777

819
832
839
848
843
851
845
853
824
856
791
855
774
791
777
779

1010
1163
1235
1234
1241
1243
1248
1247
1253
1252
1256
1255
1260
1263
1262
1171

1073
1235
1242
1242
1247
1247
1254
1250
1255
1256
1259
1260
1263
1265
1265
1173

1140
1243
1248
1246
1251
1253
1258
1256
1259
1258
1264
1262
1267
1267
1265
1175

1501
1467
1744
1644
1849
1746
1810
1866
1868
1870
1874
1876
1879
1699
1696
1699

1595
1559
1848
1718
1860
1745
1810
1872
1874
1877
1878
1881
1885
1700
1695
1701

1694
1656
1859
1719
1867
1745
1812
1877
1880
1882
1883
1887
1889
1700
1696
1696

2066
2206
2309
2324
2407
2354
2423
2379
2433
2407
2441
2178
2181
2184
2187
2129

2195
2310
2408
2370
2421
2384
2435
2405
2440
2414
2449
2185
2185
2188
2191
2135

2249
2348
2422
2370
2431
2408
2443
2414
2449
2413
2456
2188
2189
2193
2194
2138

2313
2350
2464
2517
2637
2673
2670
2498
2700
2701
2566
2674
2715
2719
2436
2438

2459
2496
2618
2590
2682
2688
2705
2525
2729
2711
2728
2719
2721
2725
2441
2444

2611
2558
2683
2589
2682
2699
2732
2547
2730
2718
2731
2728
2726
2728
2448
2447

2570
2772
2889
2813
2789
2813
2923
2813
2922
2851
2959
3003
3023
3038
2688
2690

2695
2813
2888
2812
2789
2812
2922
2813
2922
2849
2960
3003
3023
3036
2691
2693

2694
2813
2888
2812
2788
2812
2923
2812
2922
2851
2958
3002
3021
3039
2696
2698

2588
2863
3133
3210
3392
3449
3618
3656
3795
3616
3914
3640
3652
3669
3677
3405

3397
3657
3752
3697
3841
3698
3696
3718
3841
3880
3899
3899
3939
3938
3485
3496

3467
3697
3841
3698
3840
3698
3697
3718
3841
3879
3901
3899
3940
3937
3505
3513

3468
3698
3841
3696
3841
3698
3697
3719
3840
3880
3899
3900
3940
3937
3525
3530

4343
4224
4349
4740
4525
4632
5048
4999
5220
5407
5397
5450
5450
5461
5424
5438

4615
4488
4622
5038
4808
4920
5155
5312
5494
5494
5397
5451
5448
5462
5457
5468

4901
4766
4908
5154
5105
5227
5154
5493
5493
5494
5397
5448
5451
5461
5486
5495

3041
3329
3410
3604
3665
3844
3885
3912
3639
3927
3664
3674
3689
3696
3421

2920
3230
3536
3622
3828
3891
3915
3921
3926
3662
3938
3685
3694
3706
3714
3441

Pound-inches at low-speed shaft multiply values listed by 1000.


See page21 for availability of Type A, AR, AXV triple reduction.
For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

26 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Triple Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
Approx.
HighLowSpeed Nominal
Ratios
Speed
Shaft
4%
Shaft
RPM
RPM

870

720

580

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

38.0
34.0
31.0
28.0
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
31.0
28.0
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

16.0
14.6
13.8
12.1
11.4
9.68
8.98
7.90
7.34
6.78
6.24
5.54
4.62
4.43
3.98
3.72
3.19
2.98

13.3
12.1
11.4
10.0
9.45
8.01
7.44
6.54
6.08
5.61
5.16
4.58
3.82
3.67
3.30
3.08
2.64
2.47

10.8
9.74
9.21
8.06
7.62
6.45
5.99
5.27
4.90
4.52
4.16
3.69
3.08
2.96
2.66
2.48
2.13
1.99

24.9
25.2
20.4
17.6
17.3
16.2
13.0
12.1
9.26
9.26
8.88
8.12
7.53
6.88
4.29
4.29
4.29
4.29

20.6
20.9
16.9
14.7
14.3
13.4
10.8
10.0
7.69
7.69
7.35
6.73
6.23
5.70
3.56
3.56
3.56
3.56

16.6
16.8
13.6
11.9
11.6
10.8
8.77
8.09
6.22
6.22
5.93
5.42
5.02
4.59
2.87
2.87
2.87
2.87

34.4
34.4
27.9
27.9
26.0
24.6
21.5
19.3
16.9
16.4
14.4
12.8
11.8
10.6
9.80
8.71
8.03
7.25

28.7
28.7
23.2
23.2
21.5
20.3
17.8
16.0
14.0
13.6
11.9
10.6
9.76
8.81
8.11
7.21
6.65
6.00

23.2
23.2
18.8
18.8
17.3
16.4
14.4
12.9
11.3
11.0
9.60
8.54
7.87
7.10
6.54
5.81
5.36
4.83

49.5
49.5
49.5
44.4
38.1
33.8
30.6
27.9
25.2
20.7
19.8
17.6
16.4
14.5
13.2
11.7
10.4
9.90

41.3
41.3
41.3
36.8
31.5
28.0
25.4
23.2
20.9
17.2
16.4
14.6
13.6
12.0
10.9
9.70
8.66
8.19

33.5
33.5
33.5
29.7
25.4
22.6
20.4
18.8
16.8
13.9
13.2
11.7
10.9
9.70
8.80
7.81
7.00
6.60

95.5
90.0
78.5
72.3
63.2
59.5
56.9
46.9
44.9
40.5
38.4
33.2
31.4
26.9
21.5

79.0
74.5
65.0
59.8
52.3
49.2
47.1
38.8
37.1
33.5
31.7
27.4
26.0
22.2
17.8

63.7
60.0
52.4
48.2
42.1
39.6
37.9
31.2
29.9
27.0
25.6
22.1
20.9
17.9
14.3

147
149
130
117
103
93.2
85.6
77.4
71.1
64.2
59.0
45.3
45.9
40.0
34.2
31.4

123
123
108
97.1
85.1
77.2
70.9
64.1
58.9
53.2
48.8
37.5
38.0
33.1
28.3
26.0

99.7
99.6
87.1
78.3
68.8
62.2
57.2
51.7
47.5
42.8
39.4
30.3
30.6
26.7
22.8
21.0

211
186
178
165
145
134
108
115
106
90.5
72.6
77.5
70.9
60.3
49.7
45.4

175
154
148
137
120
111
89.1
95.2
87.5
74.9
60.1
64.2
58.7
50.0
41.1
37.6

141
124
119
110
96.7
89.5
71.7
76.7
70.5
60.3
48.4
51.7
47.3
40.4
33.1
30.3

364
325
300
268
252
214
205
179
160
146
132
116
105
97.5
82.9
65.9

302
270
249
222
209
178
170
149
133
121
110
96.0
87.0
80.7
68.6
54.6

244
218
201
180
168
143
137
120
107
97.4
88.3
77.4
70.1
65.0
55.3
44.0

523
458
432
378
351
307
286
250
224
200
177
169
135
122
110
102

434
380
358
313
291
255
237
207
186
166
146
140
112
101
91.1
84.2

351
307
289
253
235
206
191
167
150
134
118
113
90.2
81.3
73.5
67.8

713
655
604
559
516
441
407
378
348
301
277
240
221
203
188
159

590
544
501
464
428
366
337
313
289
249
230
199
183
168
156
132

476
439
405
375
345
295
272
253
233
201
185
160
148
136
125
106

1033
891
938
760
759
623
601
538
502
460
423
369
339
278
255
235

855
737
779
629
630
516
498
446
416
381
350
305
281
230
211
194

689
594
629
507
509
416
401
360
336
308
283
246
226
185
170
156

1389
1316
1210
1077
1002
859
787
727
668
577
531
420
400
353
311
280

1149
1099
1004
891
832
711
653
602
554
478
440
348
332
292
258
232

926
885
811
718
672
572
527
485
447
385
355
281
268
236
208
187

1651
1389
1348
1120
1074
985
856
738
725
657
576
522
498
439
351
334

1366
1149
1115
927
889
818
709
614
600
545
476
433
413
364
291
277

1101
926
899
747
716
660
571
497
484
439
384
349
333
294
234
223

1622
1555
1408
1228
1109
991
942
845
804
691
657
585
547
477
379
349

1342
1287
1165
1016
918
820
780
700
665
572
544
484
452
395
314
289

1081
1037
939
819
740
660
628
564
536
461
438
390
364
318
253
233

1969
1969
1908
1704
1529
1395
1237
1151
1058
909
856
737
674
587
540
449

1715
1715
1601
1410
1269
1158
1027
955
878
756
709
613
560
488
449
373

1382
1382
1294
1136
1025
935
829
771
708
612
572
496
453
395
363
301

2090
1945
1860
1614
1544
1308
1181
1105
979
907
848
747
702
649
525
481

1730
1610
1539
1336
1277
1082
978
914
810
751
702
618
581
537
436
399

1393
1297
1240
1076
1029
872
788
737
653
605
565
498
468
433
353
323

3006
2782
2498
2201
2245
2073
1784
1623
1465
1298
1204
1078
950
879
804
735

2488
2428
2117
1822
1858
1715
1477
1343
1212
1074
997
892
786
727
666
608

2004
1956
1705
1468
1497
1382
1189
1082
977
865
803
719
633
586
536
490

See page21 for availability of Type A, AR, AXV triple reduction.


For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

Rexnord 2014

(131-110) 27

Horsepower & Torque Ratings/Triple Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
HighApprox.
Speed Nominal
LowRatios
Shaft
Speed
4%
RPM
Shaft RPM

870

720

580

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

38.0
34.0
31.0
28.0
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
31.0
28.0
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
25.0
22.0
21.0
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7

Drive Size
305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

44.3
44.0
46.5
44.1
46.5
44.8
46.5
44.8
46.6
45.2
46.6
45.7
43.1
45.6
45.6
45.7
45.6
45.7

44.5
44.0
46.4
44.0
46.5
44.8
46.6
44.8
46.6
45.2
46.6
45.6
43.0
45.6
45.7
45.7
45.6
45.8

44.8
44.0
46.6
44.0
46.6
44.8
46.5
44.8
46.6
45.2
46.6
45.6
43.1
45.7
45.7
45.7
45.7
45.8

70.7
76.1
70.7
67.8
70.8
76.1
69.5
71.1
60.6
64.4
70.9
71.3
71.0
71.3
51.0
56.1
60.2
66.2

70.7
76.2
70.8
68.4
70.7
76.1
69.8
71.0
60.8
64.7
70.9
71.4
71.0
71.4
51.2
56.2
60.4
66.4

70.7
76.1
70.7
68.7
71.2
76.1
70.3
71.3
61.1
64.9
71.1
71.4
71.0
71.4
51.2
56.3
60.5
66.4

96.8
108
95.6
106
111
113
110
113
110
113
111
107
109
107
111
107
109
108

97.6
109
96.0
107
110
113
110
113
110
113
111
107
109
107
111
107
109
108

97.9
109
96.6
108
110
113
111
113
111
114
111
108
109
108
111
107
109
107

137
152
164
164
154
150
154
156
155
147
154
150
155
150
155
150
144
150

138
153
165
164
154
150
155
157
155
148
155
150
155
150
155
150
145
150

139
155
166
164
154
150
154
157
155
148
154
149
154
150
155
150
146
150

154
163
154
166
157
166
172
166
173
168
173
174
176
177
153

154
163
154
166
157
166
172
166
172
168
172
174
176
176
153

154
163
154
166
157
166
172
166
172
168
173
174
176
176
153

238
263
259
263
258
264
264
264
264
264
264
241
253
241
241
241

240
262
260
264
258
264
264
264
264
265
264
241
253
241
241
241

242
264
260
264
259
264
264
265
265
264
265
241
253
241
241
242

360
344
360
384
360
383
336
390
385
384
335
390
390
372
340
340

360
344
361
385
360
384
335
390
384
384
335
390
391
373
339
340

361
344
361
384
360
384
335
390
384
384
335
390
391
374
339
340

605
586
606
587
608
588
610
588
597
591
582
592
583
587
586
499

607
588
608
587
610
591
611
592
600
592
586
592
584
587
586
499

609
590
609
591
608
590
611
592
599
592
584
592
584
587
587
500

841
850
844
852
845
853
848
856
831
856
794
856
776
796
777
780

843
852
845
852
846
856
849
856
833
858
792
857
778
797
777
778

847
855
847
855
849
858
850
857
834
860
794
859
778
796
778
778

1181
1250
1255
1253
1259
1257
1263
1259
1262
1263
1265
1265
1267
1267
1270
1174

1181
1254
1257
1256
1261
1261
1264
1260
1266
1263
1270
1267
1268
1267
1273
1178

1183
1257
1262
1261
1262
1262
1266
1264
1267
1265
1268
1265
1273
1273
1266
1174

1772
1693
1870
1717
1875
1745
1810
1883
1886
1887
1889
1892
1893
1699
1696
1702

1772
1692
1876
1717
1881
1746
1812
1886
1888
1888
1889
1890
1896
1699
1695
1698

1773
1693
1881
1718
1887
1747
1812
1890
1893
1895
1896
1892
1893
1696
1696
1695

2249
2393
2437
2371
2443
2415
2451
2413
2456
2413
2460
2195
2193
2197
2196
2141

2248
2415
2443
2370
2451
2415
2457
2414
2461
2415
2463
2198
2200
2196
2201
2144

2249
2414
2450
2371
2458
2412
2462
2415
2465
2415
2467
2203
2204
2203
2203
2145

2667
2558
2683
2588
2682
2713
2730
2571
2730
2728
2733
2731
2733
2735
2453
2448

2666
2556
2681
2588
2683
2722
2733
2585
2730
2735
2729
2738
2739
2740
2457
2454

2668
2558
2684
2589
2682
2727
2732
2597
2734
2735
2733
2739
2741
2747
2453
2452

2695
2812
2889
2813
2787
2813
2923
2811
2923
2849
2960
3004
3023
3036
2700
2706

2694
2812
2888
2812
2788
2813
2924
2814
2921
2850
2962
3004
3019
3038
2703
2707

2694
2813
2890
2814
2790
2811
2923
2814
2923
2851
2960
3004
3018
3036
2703
2710

3191
3530
3864
3870
3922
3927
3933
3939
3942
3693
3953
3711
3720
3731
3736
3463

3359
3715
3918
3869
3934
3939
3946
3949
3953
3712
3956
3730
3735
3748
3754
3476

3360
3716
3931
3870
3944
3948
3954
3957
3957
3730
3962
3747
3751
3766
3767
3482

3467
3697
3840
3697
3841
3698
3696
3719
3839
3879
3900
3898
3936
3936
3545
3556

3468
3698
3839
3698
3839
3696
3698
3717
3838
3881
3902
3897
3936
3935
3558
3565

3466
3698
3840
3697
3840
3698
3699
3721
3841
3881
3898
3898
3936
3939
3576
3582

5091
5209
5365
5153
5493
5495
5154
5494
5494
5493
5395
5451
5450
5461
5492
5492

5091
5494
5494
5154
5493
5493
5156
5494
5492
5492
5398
5450
5448
5458
5497
5489

5091
5494
5493
5155
5494
5495
5153
5494
5496
5491
5397
5453
5447
5461
5492
5492

Pound-inches at low-speed shaft multiply values listed by 1000.


See page21 for availability of Type A, AR, AXV triple reduction.
For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

28 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Quadruple Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
High-Speed
Shaft RPM

1750

1430

1170

LowNominal Approx.Shaft
Ratios 5% Speed
RPM

105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9

16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2
2.9
2.7

Drive Size
385

405

425

445

465

485

505

525

535

555

42.6
40.8
36.9
35.3
28.6
28.6
23.2
22.2
20.0
19.2
15.6
15.5
13.3
10.6

34.8
33.4
30.1
28.8
23.4
23.3
18.9
18.1
16.4
15.7
12.7
12.7
10.8
8.68

28.5
27.3
24.7
23.6
19.1
19.1
15.5
14.8
13.4
12.8
10.4
10.4
8.87
7.10

56.5
58.4
47.3
41.7
38.4
32.9
30.8
31.8
25.7
22.4
20.9
18.2
16.9
15.6

46.2
47.8
38.7
34.1
31.4
27.2
25.1
26.0
21.0
18.3
17.0
14.9
13.8
12.7

37.8
39.1
31.6
27.9
25.7
22.4
20.6
21.3
17.2
15.0
13.9
12.2
11.3
10.4

80.3
85.8
78.9
67.5
54.1
57.9
52.9
45.1
37.1
39.0
35.6
30.5
25.0
22.8

65.6
70.1
64.5
55.2
44.2
47.3
43.2
36.9
30.3
31.9
29.1
24.9
20.4
18.7

53.7
57.4
52.8
45.2
36.2
38.7
35.4
30.3
24.8
26.1
23.8
20.4
16.7
15.3

139
133
117
106
96.5
84.5
76.6
71.6
64.8
56.9
51.4
47.7
40.6
32.3

114
109
95.9
87.0
78.8
69.1
62.6
58.5
53.0
46.5
42.0
39.0
33.2
26.4

93.1
89.4
78.6
71.3
64.5
56.6
51.2
47.9
43.3
38.0
34.4
31.9
27.1
21.6

211
184
166
147
130
125
112
99.6
87.8
84.1
67.1
60.5
54.7
50.5

172
151
136
121
106
102
91.8
81.4
71.8
68.8
54.8
49.4
44.7
41.3

141
123
111
98.7
87.1
83.4
75.2
66.6
58.8
56.3
44.9
40.4
36.6
33.8

303
282
260
224
206
179
165
145
133
115
106
97.6
90.2
82.9

248
231
212
183
169
146
135
118
109
94.2
86.8
79.8
73.7
67.8

203
189
174
150
138
120
110
96.8
89.2
77.1
71.0
65.3
60.4
55.5

462
387
347
333
299
266
235
228
210
183
168
137
116
111

378
316
283
272
244
218
192
187
171
149
137
112
94.7
90.3

310
259
232
223
200
178
157
153
140
122
112
91.8
77.5
73.9

570
524
483
416
384
291
289
285
264
208
184
167
154
139

466
429
395
340
314
242
237
233
216
170
150
136
126
113

382
351
324
278
257
201
194
191
176
139
123
112
103
92.8

594
594
523
475
415
377
360
291
284
259
247
218
174
153

485
485
427
389
339
309
294
242
232
212
202
178
142
125

402
402
350
318
278
253
241
201
190
173
165
146
116
103

812
812
765
706
610
531
507
454
395
365
303
279
241
222

705
674
626
578
501
436
418
372
324
299
248
228
197
182

586
552
513
473
411
358
348
306
266
245
204
187
162
149

For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

385

405

425

X
X
X

X
X
X

Availability of Types A / AR / AXV Quadruple Reduction


445
465
485
505

X
X
X

X
X
X

X
X
X

X
X
X

525

535

555

X
X

X
X

Rexnord 2014

(131-110) 29

Horsepower & Torque Ratings/Quadruple Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
Drive Size

LowHigh-Speed
Nominal Approx.Shaft
Shaft RPM Ratios 5% Speed
RPM

385

405

425

445

465

485

505

525

535

555

105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9

166
172
168
174
163
176
167
173
168
175
164
176
177
153

166
173
168
174
163
176
166
172
168
175
163
177
176
153

166
172
168
174
163
176
167
172
168
174
163
177
176
153

240
264
252
252
253
236
241
265
253
241
253
241
241
242

241
265
253
252
253
239
241
265
253
241
252
242
241
241

241
265
252
252
253
240
241
266
253
241
252
242
241
241

335
390
384
384
335
390
390
373
340
390
390
374
340
340

335
390
384
384
335
390
390
374
340
390
390
374
339
341

335
390
384
384
335
390
391
375
340
390
390
375
340
341

568
589
600
589
584
592
584
593
584
593
584
587
587
500

570
591
602
592
584
592
584
592
585
593
584
587
587
500

569
592
603
593
584
593
584
593
584
593
584
587
586
500

852
857
837
856
794
862
838
860
795
860
778
797
779
779

850
861
840
862
792
861
841
860
796
861
778
796
779
780

851
857
838
859
795
860
842
860
796
861
779
796
780
780

1265
1264
1268
1265
1266
1269
1273
1271
1269
1265
1269
1272
1272
1272

1267
1267
1265
1264
1271
1266
1275
1266
1272
1268
1272
1273
1272
1273

1268
1267
1269
1267
1268
1272
1269
1269
1273
1269
1272
1273
1274
1274

1886
1761
1812
1894
1829
1891
1828
1893
1899
1899
1899
1695
1700
1724

1889
1760
1808
1893
1827
1897
1828
1900
1892
1892
1895
1696
1699
1717

1893
1763
1812
1897
1830
1893
1827
1900
1893
1894
1893
1699
1699
1717

2462
2412
2462
2413
2467
2136
2197
2412
2475
2201
2209
2206
2201
2151

2463
2416
2464
2413
2468
2174
2205
2414
2478
2201
2204
2199
2204
2140

2467
2416
2471
2411
2469
2207
2206
2418
2468
2200
2208
2213
2202
2148

2429
2678
2731
2736
2731
2736
2740
2446
2728
2743
2744
2749
2461
2456

2427
2676
2729
2742
2730
2744
2738
2489
2727
2748
2746
2747
2458
2455

2458
2711
2734
2739
2736
2746
2744
2527
2729
2741
2742
2753
2454
2473

3526
3901
3955
3958
3730
3739
3844
3754
3761
3769
3488
3496
3502
3511

3747
3962
3960
3966
3749
3757
3879
3764
3776
3779
3494
3496
3503
3523

3806
3966
3967
3966
3759
3770
3947
3785
3789
3784
3512
3504
3521
3525

1750

1430

1170

16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2
2.9
2.7

Pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

385

405

425

X
X
X

X
X
X

Availability of Types A / AR / AXV Quadruple Reduction


445
465
485
505

X
X
X

30 (131-110)

X
X
X

X
X
X

X
X
X

525

535

555

X
X

X
X

Rexnord 2014

Horsepower & Torque Ratings/Quadruple Reduction


Horsepower Ratings
Type A, AR & AXV Parallel Shaft
Drive Size

LowHigh-Speed
Nominal Approx.Shaft
Shaft RPM Ratios 5% Speed
RPM

385

405

425

445

465

485

505

525

535

555

105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9

21.2
20.3
18.3
17.5
14.3
14.2
11.5
11.0
9.95
9.52
7.76
7.71
6.60
5.28

17.5
16.8
15.2
14.5
11.8
11.8
9.53
9.12
8.24
7.88
6.42
6.38
5.46
4.37

14.1
13.5
12.2
11.7
9.52
9.47
7.67
7.34
6.64
6.35
5.18
5.14
4.40
3.52

28.2
29.1
23.5
20.8
19.1
16.8
15.3
15.8
12.8
11.2
10.4
9.05
8.42
7.74

23.3
24.1
19.5
17.2
15.8
14.0
12.7
13.1
10.6
9.24
8.59
7.49
6.97
6.40

18.8
19.4
15.7
13.9
12.7
11.3
10.2
10.5
8.53
7.45
6.92
6.04
5.61
5.16

39.9
42.7
39.2
33.6
26.9
28.8
26.3
22.5
18.4
19.4
17.7
15.2
12.4
11.4

33.0
35.3
32.5
27.8
22.3
23.8
21.8
18.7
15.3
16.0
14.7
12.6
10.3
9.40

26.6
28.4
26.2
22.4
17.9
19.2
17.5
15.0
12.3
12.9
11.8
10.1
8.29
7.57

69.2
66.5
58.6
53.0
48.0
42.1
38.1
35.6
32.2
28.3
25.6
23.7
20.2
16.1

57.3
55.1
48.5
43.9
39.7
34.9
31.5
29.5
26.7
23.4
21.2
19.6
16.7
13.3

46.1
44.4
39.1
35.4
32.0
28.1
25.4
23.8
21.5
18.9
17.0
15.8
13.4
10.7

105
91.8
82.9
73.5
64.8
62.1
56.0
49.6
43.7
41.9
33.4
30.1
27.2
25.1

87.0
76.0
68.7
60.8
53.7
51.4
46.4
41.0
36.2
34.7
27.6
24.9
22.5
20.8

70.1
61.3
55.4
49.0
43.2
41.4
37.4
33.1
29.2
27.9
22.3
20.1
18.1
16.7

151
141
130
112
103
89.0
82.0
72.0
66.3
57.4
52.9
48.6
44.9
41.3

125
116
107
92.4
85.2
73.7
67.9
59.6
54.9
47.5
43.8
40.2
37.2
34.1

101
93.8
86.4
74.5
68.6
59.4
54.7
48.0
44.2
38.3
35.3
32.4
29.9
27.5

231
192
172
166
148
133
117
114
104
91.0
83.6
68.3
57.6
55.0

191
159
143
137
123
110
96.8
94.2
86.5
75.3
69.2
56.5
47.7
45.5

154
128
115
111
99.0
88.6
78.0
75.9
69.7
60.7
55.8
45.5
38.4
36.6

284
261
241
207
191
152
144
142
131
104
91.4
83.1
76.8
69.0

236
216
200
171
159
127
119
117
109
85.8
75.7
68.8
63.6
57.1

190
174
161
138
128
103
96.2
94.5
87.6
69.2
61.0
55.4
51.2
46.0

307
302
260
237
206
188
179
152
141
129
123
108
86.5
76.3

257
250
215
196
171
156
149
127
117
107
102
89.8
71.6
63.1

209
202
173
158
138
126
120
103
94.3
86.1
82.1
72.3
57.7
50.9

435
411
382
352
307
267
261
228
199
183
152
140
121
111

360
340
316
292
255
222
216
189
165
152
126
116
100
92.1

290
274
255
235
206
179
174
153
133
123
102
93.6
80.8
74.3

870

720

580

8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6
1.5
1.3

For Size 555ARJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page32 for instructions.

High-Speed
Shaft RPM

Type

All

A
AR
AXV

385

405

425

X
X
X

X
X
X

Availability of Types A / AR / AXV Quadruple Reduction


445
465
485
505

X
X
X

X
X
X

X
X
X

X
X
X

525

535

555

X
X

X
X

Rexnord 2014

(131-110) 31

Horsepower & Torque Ratings/Quadruple Reduction


Torque Ratings
Type A, AR & AXV Parallel Shaft
Drive Size

LowHigh-Speed
Nominal Approx.Shaft
Shaft RPM Ratios 5% Speed
RPM

385

405

425

445

465

485

505

525

535

555

105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9

166
172
168
174
164
176
166
172
168
174
164
176
176
153

166
172
168
174
163
177
166
172
168
174
164
176
176
153

166
172
168
174
164
176
166
172
168
174
164
176
176
153

241
265
252
253
253
242
241
265
253
242
254
241
241
242

241
265
253
253
253
244
242
265
253
241
253
241
242
241

241
265
253
254
252
244
241
264
253
242
253
242
241
242

335
390
384
384
335
390
390
374
339
390
390
375
339
342

335
390
384
384
335
390
391
376
341
389
391
376
340
340

335
389
385
384
334
390
390
374
340
389
390
374
340
340

568
592
604
593
585
593
585
593
584
594
585
586
587
501

569
593
604
593
584
594
584
593
585
593
585
586
587
500

568
593
605
594
585
594
585
594
585
595
582
586
584
500

852
860
841
861
796
861
843
861
796
862
779
797
779
779

853
860
842
860
797
861
844
860
797
862
778
797
779
780

854
861
843
861
796
861
844
862
798
861
781
799
778
777

1268
1271
1275
1272
1273
1269
1273
1269
1272
1270
1274
1274
1273
1275

1268
1263
1268
1268
1273
1270
1273
1269
1273
1270
1275
1274
1275
1272

1272
1268
1271
1269
1272
1270
1273
1269
1272
1271
1275
1274
1272
1273

1897
1757
1806
1899
1821
1902
1831
1904
1891
1900
1900
1700
1698
1719

1895
1759
1815
1894
1829
1901
1830
1901
1901
1899
1901
1699
1699
1718

1897
1757
1812
1905
1827
1901
1831
1901
1901
1901
1903
1699
1698
1715

2467
2416
2472
2415
2468
2244
2202
2418
2471
2213
2207
2208
2208
2148

2477
2416
2478
2410
2483
2266
2199
2407
2484
2206
2209
2209
2209
2148

2476
2416
2477
2415
2481
2281
2207
2413
2478
2209
2209
2208
2208
2148

2525
2739
2731
2746
2727
2744
2740
2570
2724
2748
2749
2739
2461
2463

2554
2740
2729
2744
2735
2751
2756
2595
2731
2755
2754
2752
2462
2461

2578
2748
2726
2746
2740
2759
2756
2612
2733
2751
2752
2751
2463
2465

3800
3971
3972
3969
3776
3781
3981
3792
3812
3801
3520
3528
3537
3531

3800
3970
3971
3979
3789
3799
3981
3799
3819
3815
3525
3533
3532
3540

3800
3971
3978
3975
3800
3803
3981
3817
3821
3832
3543
3538
3542
3546

870

720

580

8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6
1.5
1.3

Pound-inches at low-speed shaft multiply values listed by 1000.


For the Size 555ARJ gear drive (hollow low-speed shaft with shrink disc connection), the maximum output torque rating is limited to 3,100,000 lb-in by the shrink disc, and
this shrink disc torque rating supersedes any higher torque ratings for the 555ARJ that may be shown on torque pages 22, 24, 26, 28, 30 and 32. In those cases
where your 555ARJ is selected at a High-Speed Shaft RPM and Nominal Ratio where the torque rating of the gear drive is limited by the shrink disc (3,100,000 lb-in),
you must calculate an Equivalent Power Rating (HP) for the 555ARJ gear drive using the formula below:

3,100,000 lb-in
Torque Rating (lb-in) from pages 22, 24, 26, 28, 30 or 32

High-Speed
Shaft RPM

Type

All

A
AR
AXV

385

405

425

X
X
X

X
X
X

x Power Rating (HP) from pages 21, 23, 25, 27, 29 or 31 = Equivalent Power Rating (HP)

Availability of Types A / AR / AXV Quadruple Reduction


445
465
485
505

X
X
X

32 (131-110)

X
X
X

X
X
X

X
X
X

525

535

555

X
X

X
X

Rexnord 2014

Type A Technical Data and Dimensions


Basic Thermal Horsepower Ratings
Single Reduction
Type A Basic Thermal Horsepower Ratings
Drive Size
Nominal
Ratios

High-Speed
Shaft RPM

1750

1430

1.84 Thru
3.05
Sizes 305
thru 525

1170

870

720

580

1750
3.38 Thru
5.60
Sizes 305
Thru 365

1430

1170

870
3.38 Thru
5.06
Sizes 385
Thru 525

720

580

Auxiliary
Cooling

305

325

345

365

None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes
None
2 Shaft Fans
Cooling Tubes

131
262
597
136
239
556
136
217
515
133
192
454
129
177
419
124
163
380
108
198
394
106
177
362
103
159
332
97.0
137
291
93.0
126
266
86.1
111
240

194
420
814
200
380
757
200
344
701
196
299
623
191
275
574
184
250
522
150
295
515
146
262
474
142
235
436
134
200
383
128
182
350
122
164
318

268
563
1137
275
509
1064
277
463
989
270
405
881
264
373
814
254
340
742
196
380
701
194
339
648
188
304
598
178
262
525
171
239
483
163
216
440

322
763
1317
341
691
1246
348
627
1166
347
547
1047
339
503
972
329
459
891
250
534
847
250
476
789
246
426
732
236
365
649
228
332
601
218
300
546

385

405

425

445

465

485

505

525

1357

1699

3069

3793

4715

6401

7112

7164

1254

1594

2871

3569

4504

6137

6927

7191

1168

1501

2700

3398

4320

5927

6783

7230

1018

1317

2371

3016

3859

5334

6190

6717

944

1226

2199

2818

3635

5044

5874

6466

874

1136

2051

2632

3420

4765

5594

6234

1009

1212

1976

2450

3227

4478

5018

5874

931

1122

1831

2278

3029

4214

4794

5742

869

1051

1712

2134

2871

4004

4596

5637

778

915

1488

1883

2542

3556

4109

5149

734

847

1370

1752

2384

3332

3859

4912

692

784

1272

1622

2221

3126

3625

4090

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
Gear drives at 1750 RPM require jet lubrication and special labyrinth seals; gear drives at 1430 RPM require jet lubrication, refer to Factory.
No auxiliary cooling (None) and 2 shaft fans are not offered. Use electric fan or cooling tubes.

For basic thermal ratings with electric fan, see page34.
For cooling beyond the range of values listed, see oil-to-air cooler selections, page35.

Basic Thermal Horsepower Rating with One Shaft Fan


Calculate thermal rating for gear drives with one shaft fan as follows: Average the
thermal rating without auxiliary cooling and the thermal rating with 2 shaft fans.
Example: Size 425A2, 17.09:1 ratio at 1750 rpm
Thermal Rating without Auxiliary Cooling (page36) = 187
Thermal Rating with 2 Shaft Fans (page36) = 449
187 + 449
2

= 318 Thermal Rating with One Shaft Fan

Rexnord 2014

(131-110) 33

Basic Thermal Horsepower Ratings


Basic Electric Fan/Single Reduction
Type A Basic Electric Fan Thermal Ratings
High-Speed
Shaft RPM

1750

1430

1170

870

720

580

Drive Size

Nominal
Ratios
3%

Approx.
L.S. Shaft
RPM

385

405

425

445

465

485

505

525

1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06

950
860
780
700
640
575
520
470
420
380
350
780
700
640
575
520
470
420
380
350
310
280
640
575
520
470
420
380
350
310
280
255
230
470
430
390
350
320
290
260
235
210
190
175
390
350
320
290
260
235
210
190
175
155
140
320
290
260
235
210
190
175
155
140
130
115

278
299
355
385
381
462
391
441
478
462
313
409
412
469
473
449
526
438
350
395
390
382
477
468
524
514
364
440
367
415
448
432
414
426
416
466
459
427
499
408
448
471
447
422
454
440
489
474
435
506
410
447
467
440
413
460
442
490
470
428
496
399
434
451
424
396

309
350
416
441
463
474
565
544
622
592
646
560
562
591
588
587
573
663
616
684
477
540
702
677
681
662
646
618
706
511
585
555
609
786
739
596
582
570
549
632
580
641
595
640
687
648
640
616
596
566
648
587
643
592
635
717
669
652
622
596
562
640
575
627
575
615

388
443
532
576
590
604
716
705
686
655
718
738
751
761
783
749
732
821
787
550
937
954
936
920
880
888
825
790
682
669
649
1120
1100
1050
1013
767
780
729
702
782
744
702
1151
945
906
881
825
830
762
725
795
750
701
1027
1006
951
916
842
841
763
719
783
734
683

587
853
935
1053
1086
1107
1069
1234
807
940
998
1100
1368
1382
1372
1347
1316
1226
1352
1300
1359
1365
1385
1643
1614
1527
1468
1408
1290
1269
1633
1626
1589
1545
1791
1730
1431
1387
1341
1235
1354
1694
1668
1618
1381
1647
1608
1504
1439
1372
1238
1324
1688
1513
1477
1441
1700
1644
1495
1409
1326
1191
1274

630
780
913
1058
1293
1307

771
911
1111
1211
1342
1385
1389
1393
1643
1584
1540
1648
1659
1746
1736
1728
1702
1629
1551
1806
1708
2287
2241
2148
2139
2048
1939
1864
1737
1478
1756
1667
2451
2359
2235
2200
2086
1788
1736
1632
1537
1804
1682
2481
2364
2224
2065
1967
1854
1780
1647
1506
1748
1626

734
854
951

820
1127
1237
1366
1360
1346

911
1205
1300
1469
1512
1711
1733
1705
1623
1542
1771
1831
2105
2037
2035
1973
2073
2028
1887
1544
1478
2078
2069
2326
2207
2152
2059
2128
1864
1778
1665
1561
2205
2154
2396
2248
1993
1919
2022
1975
1821
1669
1535

947
1245

810
1035
1358
1571
1665
1875

1242
1400
1580
1713
1783
2091
2060
2044
2194
2456
2085
2534
2505
2515
2333
2266
2546
2330
2238
1961
3000
2456
2867
2776
2730
2454
2347
2612
2026
1972
2089
3248
2608
2987
2859
2781
2148
2070
2321
2109
2020
2114

1552
1723
1887
1967
2360
2348
2634
2185
2223
2825
2860
2817
2844
2828
2676
2945
2800
3022
2917
2813
3397
3348
3142
3121
3048
2824
3050
2438
2675
3292
3099
3658
3558
3256
3208
3100
2498
2736
2592
2798

Basis thermal capacities listed are for an ambient temperature of 80F at an elevation from sea level to 2500 feet. Application-adjusted thermal capacity must be determined by using
the modification factors before comparing to the required load.

34 (131-110)

Rexnord 2014

Basic Thermal Horsepower Ratings


600PA Integrated Cooler Selections
Max. Ambient Temperature = 120F
Min. Service Factor = 1.25
Max. Altitude = 10,000 ft
For input speeds below 1170 rpm, use 1170 rpm selection.
Type A Oil-to-Air Coolers Drive Mounted
Input
RPM

Nominal
Ratios

Drive Size
385

405

425

445

465

485

505

525

1.84
2.03

620PA

630PA

640PA

2.25
2.49
2.76
1750

3.05
3.38
3.74
4.13
4.57
5.06

1.84
2.03

630PA

2.25
2.49
2.76
1430

3.05
3.38
3.74

605PA
601PA

620PA

4.13
4.57
5.06
1.84
2.03
2.25
2.49
2.76
1170

3.05

620PA

630PA

3.38
3.74
4.13
4.57
5.06

Rexnord 2014

(131-110) 35

Basic Thermal Horsepower Ratings


Double Reduction
Type A, AR & AXV Basic Thermal Horsepower Ratings
Nominal
Ratios

HighSpeed
Shaft
RPM

1750
6.20 thru
13.95
Sizes 305
thru 365

1430

1170

870
5.60 thru
10.29
Sizes 385
thru 585

720

580

1750
5.44 thru
34.74
Sizes 305
thru 365

1430

1170

870
11.39 thru
20.93
Sizes 385
thru 585

720

580

Drive Size
Auxiliary
Cooling

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes

54.7
81.6
178
153
53.1
74.2
166
145
51.0
67.7
156
132
47.6
59.6
141
116
45.5
55.1
132
106
44.2
50.0
123
100
41.5
60.1
126
79.5
39.4
53.9
117
72.8
37.0
48.6
109
67.7
34.0
42.2
99.0
59.5
32.2
38.9
92.0
54.8
30.1
35.3
85.9
50.8

87.0
124
274
225
80.3
110
252
211
77.2
101
236
194
72.2
88.8
215
170
68.8
82.4
203
155
65.2
75.7
188
141
61.9
87.1
188
115
58.7
78.4
175
105
55.1
70.8
162
98.5
50.6
61.8
146
86.9
47.8
56.9
138
80.1
44.9
52.0
128
73.0

110
163
351
294
105
148
328
270
98.2
131
304
249
92.4
117
277
219
88.3
108
261
202
83.8
99.2
245
183
78.2
115
243
148
74.3
104
224
136
70.2
93.2
210
127
64.8
81.2
188
112
61.6
74.7
178
104
57.8
68.2
166
94.7

161
252
527
375
150
223
489
363
145
202
457
335
131
171
411
303
125
159
389
279
119
146
364
254
111
170
349
180
101
149
322
180
96.5
133
299
167
88.8
115
270
149
84.4
106
254
138
79.4
96.2
236
127

153
328
531
487
150
287
500
446
148
254
471
414
136
215
431
360
131
195
407
332
125
177
383
307
108
223
402
304
105
194
377
275
101
170
353
253
92.9
144
323
223
88.3
130
303
208
84.2
118
285
193

179
430
645
594
177
376
605
548
174
332
569
510
162
278
522
444
157
250
493
410
152
225
463
378
154
355
526
444
149
307
492
407
144
270
461
377
133
225
420
335
128
203
397
312
123
183
372
293

233
597
876
1241
229
522
826
1137
228
461
780
1052
214
384
717
907
206
344
680
835
199
308
639
767
187
449
655
809
181
390
613
734
175
341
576
674
161
281
525
598
153
250
496
560
146
223
464
524

290
795
1193
1554
291
696
1127
1422
291
617
1064
1330
275
514
981
1154
268
463
931
1064
261
416
877
984
244
623
937
1062
236
540
880
973
229
472
828
902
214
390
758
790
204
348
717
735
197
311
673
683

358
1086
1542
1989
366
950
1463
1844
372
838
1384
1725
360
701
1284
1501
353
631
1226
1396
348
567
1155
1293
316
870
1235
1409
308
751
1160
1288
301
654
1094
1187
286
543
1006
1031
277
486
954
952
270
435
898
880

405
1211
1872
2976
428
1073
1792
2766
447
962
1713
2608
438
815
1608
2305
432
741
1529
2134
428
672
1450
1992
358
948
1437
2015
357
826
1358
1870
356
728
1288
1752
337
609
1190
1515
327
550
1130
1396
318
494
1065
1285

436
1463
3071
3345
485
1310
2926
3148
525
1181
2781
3003
521
1000
2583
2687
519
909
2465
2515
518
825
2331
2356
410
1152
2425
2305
414
1006
2293
2147
416
887
2162
2028
399
742
1990
1765
390
668
1898
1646
382
601
1784
1516

465
1792
4218
3688
543
1608
4020
3530
606
1450
3835
3411
616
1236
3559
3069
621
1127
3400
2884
626
1027
3210
2715
477
1463
3348
2700
497
1289
3163
2529
513
1143
2979
2410
498
961
2755
2120
490
869
2610
1989
484
784
2452
1851

495

577

644

655

660

665

507

528

545

529

521

515

544

3466
6466
679

3387
6071
758

3295
5650
812

3124
5044
817

3005
4754
815

2876
4345
608

2768
4544
648

2662
4214
658

2544
4017
662

2372
3556
646

2267
3398
632

2150
3091

578

721

805

863

869

867

646

688

699

703

687

671

597

3796
7783
791

3769
7362
909

3690
6901
995

3532
6216
1011

3414
5847
1014

3281
5371
710

3005
5334
768

2900
4978
786

2781
4754
796

2610
4228
779

2504
4070
765

2381
3712

1160

4150
7900
1275

4020
7178
1298

3901
6717
1291

3741
6331

1120

3640
5840
1112

3255
5439
1102

3137
5057
1065

2981
4849

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
For Type AXV, apply a multiplier of 0.8 to thermal ratings with no auxiliary cooling.
Type A gear drives with backstop at high-speed shaft are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AR gear drives are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AXV gear drives are not available with shaft fans.
Size 505 ratings for Shaft Fans, Electric Fans, and Cooling Tubes apply only to Type A. Consult Rexnord for Type AR and AXV ratings.

36 (131-110)

Rexnord 2014

Basic Thermal Horsepower Ratings


Triple Reduction
Type A, AR & AXV Basic Thermal Horsepower Ratings
Nominal
Ratios

HighSpeed
Shaft
RPM

1750
38.44 thru
86.50
Sizes 305
thru 365

1430

1170

870
23.16 thru
47.08
Sizes 385
thru 585

720

580

1750
95.73 thru
215.4
Sizes 305
thru 365

1430

1170

870
52.11 thru
105.9
Sizes 385
thru 585

720

580

Drive Size
Auxiliary
Cooling

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes

26.2

78.9

24.8

73.0

23.3

67.7

21.2

61.0

20.0

56.8

18.7

52.8

20.6

60.4

19.2

55.8

17.9

51.5

16.2

46.1

15.3

43.1

14.2

39.9

37.7

114

35.6

106

33.5

98.2

30.7

88.0

28.9

82.8

27.0

76.9

28.3

83.0

26.5

76.7

24.6

70.9

22.3

63.5

20.8

59.3

19.5

55.1

49.3

152

46.9

141

44.4

131

40.7

118

38.4

110

36.0

103

38.0

113

35.7

105

33.2

97.0

30.3

87.1

28.5

81.5

26.6

75.6

67.0

208

63.0

192

59.2

179

54.0

161

50.5

150

47.3

139

50.3

154

47.2

142

43.9

131

39.9

118

37.2

110

34.7

102

89.4
133
275
242
83.2
118
256
227
78.3
106
237
215
71.8
91.6
216
184
68.7
84.6
203
170
65.6
78.1
190
155
67.0
100
212
180
63.5
89.4
198
163
60.8
80.9
185
148
55.1
69.7
166
127
52.2
64.1
156
117
49.5
58.9
146
107

109
177
347
303
100
156
323
286
93.3
137
302
271
86.9
118
273
234
83.7
109
257
216
80.7
100
241
198
80.5
131
269
223
76.4
117
250
204
73.1
105
233
190
67.2
90.4
212
165
64.3
83.0
199
150
61.6
76.1
186
138

134
214
452
558
126
190
418
523
120
170
393
494
109
146
353
439
105
134
333
410
100
123
314
383
106
166
347
408
98.2
146
319
387
92.0
131
299
369
84.6
113
270
313
81.1
103
254
286
77.6
95.1
239
260

177
298
631
728
166
264
584
682
159
236
550
644
145
202
501
572
138
185
468
536
132
168
440
502
138
228
503
531
130
202
464
498
122
179
435
470
112
154
395
403
108
141
373
369
103
130
348
337

231
414
837
951
220
365
784
890
211
327
730
842
194
278
667
749
185
254
623
703
177
231
586
660
186
323
654
698
174
283
608
655
163
252
564
620
150
215
514
533
145
196
484
490
139
180
453
449

286
554
1075
1475
279
492
1011
1343
274
442
952
1246
249
372
866
1144
236
336
820
1100
225
304
763
1050
223
415
847
1038
214
366
793
946
206
327
742
872
188
275
671
774
179
249
634
726
171
226
593
680

345
672
1977
1699
340
597
1858
1567
335
535
1740
1462
307
453
1582
1330
294
414
1489
1256
281
376
1390
1193
274
511
1503
1193
262
449
1410
1112
253
399
1315
1047
231
339
1189
932
220
308
1122
874
210
280
1049
820

415
812
2399
1976
410
726
2254
1831
405
656
2122
1712
378
561
1924
1528
364
513
1832
1436
352
468
1717
1350
349
645
1858
1383
327
561
1727
1317
308
494
1608
1264
286
420
1463
1123
274
384
1384
1054
264
349
1295
988

442

436

431

402

388

374

371

347

328

303

292

281

540
1318
1964
3767
546
1169
1872
3477
542
1041
1779
3200
507
871
1634
2950
497
795
1555
2726
481
718
1475
2472
476
1085
1595
2779
443
929
1476
2660
435
825
1397
2436
401
684
1275
2265
391
622
1213
2081
378
561
1145
1881

574

580

576

539

529

511

505

471

462

426

416

401

623
1503
2175
4675
651
1344
2082
4359
659
1217
1990
4043
650
1054
1858
3582
625
954
1766
3424
608
869
1676
3123
560
1243
1766
3516
560
1104
1674
3253
540
975
1582
3095
523
838
1463
2739
498
754
1384
2621
481
684
1312
2385

838
1885
2451
5387
863
1700
2359
5044
869
1542
2267
4689
851
1344
2122
4188
817
1217
2017
4030
793
1112
1921
3689
739
1542
1977
3951
731
1371
1872
3674
701
1217
1766
3516
673
1046
1648
3121
639
945
1555
3016
616
859
1474
2747

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
For Type AXV, apply a multiplier of 0.8 to thermal ratings with no auxiliary cooling.
Type A gear drives with backstop at high-speed shaft are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AR gear drives are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AXV gear drives are not available with shaft fans.
Size 505 ratings for Shaft Fans, Electric Fans, and Cooling Tubes apply only to Type A. Consult Rexnord for Type AR and AXV ratings.

Rexnord 2014

(131-110) 37

Basic Thermal Horsepower Ratings


Quadruple Reduction
Type A, AR & AXV Basic Thermal Horsepower Ratings
Drive Size
Nominal
Ratios

High-Speed
Shaft RPM

1750

1430

1170
117.2
thru
215.4
870

720

580

1750

1430

1170
238.4
thru
437.9
870

720

580

Auxiliary
Cooling

385

405

425

445

465

485

505

525

535

555

None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes
None
2 Shaft Fans
Electric Fan
Cooling Tubes

46.7

148

44.3

137

42.4

128

38.5

116

36.6

109

35.4

102

38.6

117

36.1

109

34.1

101

30.6

91.0

29.0

85.0

27.4

79.2

57.6

187

54.7

175

52.3

162

47.8

146

45.6

138

43.5

128

47.4

149

44.4

138

42.0

128

38.0

116

35.8

109

34.0

101

75.0

248

71.7

231

68.9

216

63.0

195

60.1

183

57.4

171

61.8

196

58.4

182

55.6

170

50.5

153

47.8

144

45.4

133

94.6
127
341
274
91.9
117
318
252
89.5
109
298
232
82.6
97.0
270
202
79.1
90.8
253
184
75.9
84.9
236
170
79.1
105
286
213
75.9
96.0
265
195
73.4
89.4
248
180
67.2
78.8
223
155
64.1
73.5
210
142
61.2
68.7
195
130

130
165
448
360
124
152
419
328
120
141
391
303
110
125
355
262
105
117
333
241
99.9
110
311
222
112
141
370
287
106
129
345
261
101
119
322
240
91.7
105
291
207
87.0
97.7
273
190
82.7
90.9
254
174

156
217
576
462
153
202
540
425
150
188
507
395
140
167
463
344
134
157
436
317
129
147
408
294
140
190
481
369
134
173
449
337
130
161
420
312
119
140
381
270
113
130
358
249
108
121
335
230

192
289
1021
576
190
268
956
531
188
252
895
494
177
223
815
432
171
207
767
402
166
193
715
373
174
254
847
469
169
233
789
432
165
216
737
400
152
190
666
348
146
177
625
321
140
164
581
296

236
386
1314
711
237
356
1231
661
239
332
1152
620
224
293
1046
544
217
273
986
506
212
254
921
470
215
337
1104
570
210
306
1031
528
207
282
961
493
191
246
871
432
183
228
817
400
177
212
763
371

251

252

253

238

232

225

228

223

219

203

195

188

317

319

320

302

293

284

288

282

278

257

247

238

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
For Type AXV, apply a multiplier of 0.8 to thermal ratings with no auxiliary cooling.
Type A gear drives with backstop at high-speed shaft are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AR gear drives are only available with one shaft fan. See instructions on page33 to calculate thermal rating with one shaft fan.
Type AXV gear drives are not available with shaft fans.
Size 505 ratings for Shaft Fans, Electric Fans, and Cooling Tubes apply only to Type A. Consult Rexnord for Type AR and AXV ratings.

38 (131-110)

Rexnord 2014

Overhung Loads
Type A, AR & AXV

Low-Speed Shaft
Calculate low-speed shaft overhung load using the formula and Fc values at left. The Lf
load location factors tabulated below are based on the distance from the centerline of the
load to the gear drive seal cage.

High & Low-Speed Shaft


126,000 x HP x Fc x Lf
Pitch Dia (in) x RPM

Overhung Load (lb) =

CENTERLINE
OF LOAD

SEAL
CAGE

= 8453 pounds

Fc = Load Connection Factor.


Sprocket
Machined Pinion & Gear
Synchronous (Timing) Belt
V-Belt
Flat Belt

Low speed shaft overhung load example An application requiring 115 hp


is driven by a 385A2 drive with 100 rpm output. An 18" pitch diameter single-chain
sprocket is mounted on the low-speed shaft and the centerline of the load is 5 inches
from the seal cage. Calculate the overhung load:

1.00
1.25
1.30
1.50
2.50

Overhung Load =

Refer to the Type A2 table on page45 and note that the overhung load capacity for a
385A2 at 100 rpm is 12,500 pounds (12.5 x 1000) and is satisfactory for this selection.

Lf = Load Location Factor.


Low-Speed Shaft See table below.
High-Speed Shaft See instructions at right.

DISTANCE

126,000 x 115 x 1.0 x 1.05


= 8453 pounds
18 x 100

High-Speed Shaft

Overhung Loads Overhung load is imposed upon a shaft when a pinion, sprocket
or sheave is used as a power take-off. The magnitude of the load varies with the type of
take-off and its proximity to the shaft bearing. Calculate the load (including minimum
required service factor) and check the result against the tabulated overhung load rating.
The above overhung load formula considers the transmitted power rating, without service
factor. This is appropriate for applications where starting loads, momentary overloads
and brake capacities do not exceed 200% of drive rating (100% overload). For other
conditions, compute the equivalent power by multiplying the transmitted power by the
appropriate service factor.

High-speed shaft overhung load ratings published on pages40-44 are for normal
conditions where the centerline of the load is one shaft diameter from the seal cage, and
for speeds of 1170 rpm or lower. Where the centerline of the load is one shaft diameter
or closer, calculate the high-speed shaft overhung load using Lf = 1 in the formula above
left. Check the result against the rating on pages40-44. Higher overhung load
capacities are available when the full gear drive torque rating is not utilized. Refer to the
Factory for higher ratings for these conditions, or if the calculated load (using Lf = 1)
exceeds the published value, or if the load is applied at a distance greater than one shaft
diameter from the high-speed shaft seal cage.

Locate the centerline of the load as close to the gear drive seal cage as practical to
minimize the effect of the overhung load and increase bearing life.
Consult Factory for Higher Overhung Load Ratings In many cases, overhung
load capacity in excess of that published is available. If the actual load should exceed
the published capacity, refer full details to the Factory; provide complete application
information (see page8), as well as direction of rotation, location and direction of
applied load.

Type A, AR & AXV


Lf Load Location Factors
Low-Speed Shaft
Based on distance from centerline of load to gear drive seal cage.
Distance
(in)

2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
10
11
12
13
14
15
16
17
18

Single Reduction
Double, Triple & Quadruple Reduction
Drive Size
Drive Size
305 325 345 365 385 405 425 445 465 485 505 525 305 325 345 365 385 405 425 445 465 485 505 525 535 545 555 565 585

0.94
0.98
1.04
1.12
1.20

0.93
0.96
1.00
1.08
1.15
1.23

0.90
0.93
0.94
0.97
1.00
1.07
1.13
1.20

0.89
0.91
0.94
0.97
1.00
1.06
1.13
1.19
1.25

0.89
0.91
0.93
0.96
0.98
1.00
1.05
1.11
1.16
1.22
1.27
1.33

0.87
0.90
0.92
0.94
0.96
0.98
1.00
1.05
1.10
1.15
1.20
1.26
1.31
1.36

0.86
0.88
0.90
0.91
0.93
0.95
0.97
0.99
1.02
1.07
1.12
1.16
1.21
1.25
1.30
1.39

Centerline of load is beyond end of


standard low-speed shaft. Consult
Factory for special shaft.

0.86
0.87
0.89
0.90
0.92
0.94
0.95
0.97
0.98
1.00
1.04
1.09
1.13
1.17
1.22
1.30
1.39

0.85
0.86
0.87
0.89
0.90
0.92
0.93
0.95
0.96
0.98
0.99
1.02
1.06
1.10
1.14
1.22
1.30
1.38

0.81
0.83
0.84
0.86
0.87
0.88
0.90
0.91
0.93
0.94
0.96
0.97
0.99
1.00
1.04
1.11
1.18
1.25
1.32
1.39

0.81
0.82
0.84
0.85
0.86
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.97
0.98
0.99
1.05
1.12
1.18
1.25
1.32
1.39
1.45

0.80
0.81
0.82
0.83
0.85
0.86
0.87
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.96
0.99
1.03
1.09
1.15
1.21
1.27
1.33
1.39
1.45

0.94
0.98
1.02
1.06
1.10

0.92
0.96
1.00
1.04
1.08
1.11

0.90
0.93
0.96
1.00
1.03
1.06
1.10

0.88
0.91
0.94
0.97
1.00
1.03
1.06
1.09
1.12

0.87
0.90
0.92
0.95
0.97
1.00
1.05
1.11
1.16
1.22
1.27
1.33

0.86
0.88
0.91
0.93
0.95
0.98
1.00
1.05
1.10
1.15
1.20
1.26
1.31
1.36

0.84
0.86
0.88
0.91
0.93
0.95
0.97
0.99
1.02
1.07
1.12
1.16
1.21
1.26
1.30
1.40

Centerline of load is beyond end of


standard low-speed shaft. Consult
Factory for special shaft.

0.83
0.85
0.87
0.89
0.91
0.92
0.94
0.96
0.98
1.00
1.04
1.09
1.13
1.17
1.22
1.30
1.39

0.82
0.84
0.86
0.87
0.89
0.91
0.92
0.94
0.96
0.97
0.99
1.02
1.06
1.10
1.14
1.22
1.30
1.38

0.81
0.83
0.84
0.86
0.87
0.88
0.90
0.91
0.93
0.94
0.96
0.97
0.99
1.00
1.04
1.11
1.18
1.25
1.32
1.39

0.81
0.82
0.84
0.85
0.86
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.97
0.98
0.99
1.05
1.12
1.18
1.25
1.32
1.39
1.45

0.80
0.81
0.82
0.83
0.85
0.86
0.87
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.96
0.99
1.03
1.09
1.15
1.21
1.27
1.33
1.39
1.45

0.77
0.79
0.80
0.81
0.83
0.84
0.85
0.87
0.88
0.89
0.91
0.92
0.93
0.95
0.96
0.99
1.03
1.09
1.15
1.20
1.26
1.32
1.38
1.44

0.80
0.81
0.82
0.83
0.84
0.83
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.96
0.99
1.02
1.07
1.13
1.18
1.24
1.29
1.34

0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.95
0.97
0.99
1.03
1.08
1.13
1.18
1.23
1.28
1.33

0.81
0.82
0.83
0.84
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.96
0.98
1.00
1.04
1.09
1.14
1.19
1.25
1.30

0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.87
0.88
0.89
0.90
0.89
0.92
0.92
0.93
0.95
0.97
0.98
1.00
1.05
1.10
1.15
1.19
1.24

Refer all multiple chain sprocket and pinion-mounted applications to the Factory for deflection analysis.
Interpolate for intermediate values.

Rexnord 2014

(131-110) 39

Overhung Loads
High-Speed Shaft
Type A, AR & AXV Overhund Loads (lb)
HighSpeed
Shaft
RPM

1170

870

Double Reduction
Drive Size

Nominal
Ratio
4%

Approx. LowSpeed Shaft


RPM

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

5.60

210

1300

950

3000

3500

2050

1110

740

6.20

190

1530

590

210

460

1300

2500

3000

3500

3510

2360

3690

3670

3080

3040

3300

6.86

170

1530

680

210

880

1300

360

2500

3000

3500

2410

1740

170

230

2320

7.59

155

1530

760

510

1100

1300

970

2500

3000

3500

2910

2960

4700

3250

2070

2700

5190

8.40

140

1530

760

840

1310

1300

180

2500

3000

3500

1840

2490

3840

5080

3880

9.30

125

1550

1010

1250

1550

1300

1210

300

2500

3000

3500

4000

4010

480

3080

1700

2590

5170

10.29

115

1550

1090

1570

1800

1300

1600

700

2500

3000

3500

1770

4700

3680

5600

4940

2690

11.39

100

1500

1060

1490

720

1300

1600

1340

2500

3000

3500

4000

4700

4700

3390

2560

1730

5150

12.61

90

1500

1060

1490

840

1300

1430

890

2500

3000

3500

1500

1660

3990

5600

3720

1530

13.95

84

1500

1080

1550

1050

1300

1600

1530

2500

3000

2870

2540

4700

2280

1460

5600

5770

3660

15.44

75

1500

1330

1900

880

1300

1600

2000

2500

3000

3500

4000

2530

990

6800

2270

17.09

68

1500

1670

2230

1070

1300

1600

1690

2500

3000

2750

3930

4700

4630

5600

6430

3980

18.91

60

1160

1390

2070

1590

1300

1600

1840

2500

3000

3500

4000

4700

4700

4650

5600

5740

4460

20.93

56

1160

1670

2370

1590

1300

1600

2000

2500

3000

3500

4000

4700

4700

4950

5600

6800

8100

23.16

50

1160

1500

2180

1790

25.63

45

1160

1670

2410

2220

28.36

40

1160

1670

2410

1820

31.39

37

1160

1670

2310

2220

34.74

34

1160

1670

2320

2490

5.60

155

1300

1010

3000

3500

2250

1220

810

1940

6.20

140

1550

580

220

490

1300

220

400

2500

3000

3500

3830

2580

4030

4020

3360

3320

3610

6.86

130

1550

580

220

950

1300

590

810

2500

3000

3500

2630

1900

200

240

2530

7.59

115

1550

640

380

1130

1300

1580

670

2500

3000

3500

3180

3230

4700

3550

2280

2950

5670

8.40

105

1550

740

820

1440

1300

800

1060

2500

3000

3500

2020

2730

4190

5550

4240

9.30

95

1550

990

1230

1860

1300

1600

1180

2500

3000

3500

4000

4390

520

3370

1840

2830

5650

10.29

85

1550

1080

1550

2210

1300

1600

1590

2500

3000

3500

1930

4700

4030

5600

5400

2940

11.39

77

1500

1370

1880

1170

1300

1600

2000

2500

3000

3500

4000

4700

4700

3710

2780

1880

5630

12.61

70

1500

1370

1880

1170

1300

1600

1770

2500

3000

3500

2070

1830

4370

5600

4070

3260

13.95

62

1500

1370

1960

1320

1300

1600

2000

2500

3000

3140

3040

4700

2510

3040

5600

6300

4000

15.44

55

1500

1630

2310

1330

1300

1600

2000

2500

3000

3500

4000

4700

1110

6800

5960

17.09

50

1500

1670

2410

1480

1300

1600

2000

2500

3000

3500

4000

4700

5600

5600

6800

8100

18.91

45

1160

1670

2410

1990

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

20.93

42

1160

1670

2410

1990

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

23.16

38

1160

1670

2410

2230

25.63

34

1160

1670

2410

2640

28.36

31

1160

1670

2410

2240

31.39

28

1160

1670

2310

2650

34.74

25

1160

1670

2320

2920

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are based on a combination of the most
unfavorable conditions of loading. Values shown apply to high-speed shaft extensions on either side of the gear drive. Consult Factory for ratings of drives with fans and for speeds
higher than 1170 RPM.
Consult Factory for overhung load ratings.

40 (131-110)

Rexnord 2014

Overhung Loads
High-Speed Shaft
Type A, AR & AXV Overhund Loads (lb)
HighNominal
Speed
Ratio
Shaft RPM 4%

5.60

720

580

Double Reduction
Drive Size

Approx. LowSpeed Shaft


RPM

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

130

1300

430

560

1080

3000

3500

2380

1290

850

5050

6.20

115

1550

580

210

710

1300

750

1020

2500

3000

3500

4000

2740

4240

4250

3540

3510

5050

6.86

105

1550

580

210

950

1300

1120

1400

2500

3000

3500

2780

2010

200

260

5050

7.59

95

1550

630

370

1130

1300

1600

1270

2500

3000

3500

3360

3430

4700

3750

2400

3130

6000

8.40

85

1550

730

800

1600

1300

1340

1660

2500

3000

3500

2120

2890

4430

5880

4490

9.30

77

1550

990

1210

2140

1300

1600

1800

2500

3000

3500

4000

4640

550

3570

1940

3000

5980

10.29

70

1550

1080

1520

2500

1300

1600

2000

2500

3000

3500

2640

4700

4260

5600

5710

5950

11.39

62

1500

1580

2120

1460

1300

1600

2000

2500

3000

3500

4000

4700

4700

4400

2960

2630

8100

12.61

55

1500

1580

2120

1460

1300

1600

2000

2500

3000

3500

3700

1950

5600

5600

4420

6360

13.95

50

1500

1580

2230

1620

1300

1600

2000

2500

3000

3500

4000

4700

2610

5150

5600

6800

4240

15.44

45

1500

1670

2410

1600

1300

1600

2000

2500

3000

3500

4000

1960

5600

1170

6800

8100

17.09

42

1500

1670

2410

1730

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

18.91

38

1160

1670

2410

2140

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

20.93

34

1160

1670

2410

2140

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

23.16

31

1160

1670

2410

2410

25.63

28

1160

1670

2410

2820

28.36

25

1160

1670

2410

2360

31.39

22

1160

1670

2310

2780

34.74

21

1160

1670

2320

3060

5.60

105

1300

1090

1290

1160

3000

3500

2540

1380

910

8100

6.20

95

1550

580

210

860

1300

1400

1750

2500

3000

3500

4000

2920

4550

4530

3770

3740

8100

6.86

85

1550

580

210

950

1300

1600

2000

2500

3000

3500

2970

2150

200

1810

8100

7.59

77

1550

630

350

1130

1300

1600

2000

2500

3000

3500

3590

3650

4700

4010

2560

3330

6410

8.40

70

1550

730

770

1660

1300

1600

2000

2500

3000

3500

3560

3080

5090

5220

6270

7140

9.30

62

1550

980

1190

2160

1300

1600

2000

2500

3000

3500

4000

4700

610

5000

5220

4200

8100

10.29

55

1550

1080

1520

2520

1300

1600

2000

2500

3000

3500

4000

4700

5600

5600

6100

8100

11.39

50

1500

1670

2120

1460

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

3170

5560

8100

12.61

45

1500

1670

2120

1460

1300

1600

2000

2500

3000

3500

4000

4700

5600

5600

6800

8100

13.95

42

1500

1670

2230

1620

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

6000

15.44

38

1500

1670

2410

1600

1300

1600

2000

2500

3000

3500

4000

4700

430

5600

1250

6800

8100

17.09

34

1500

1670

2410

1730

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

18.91

31

1160

1670

2410

2140

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

20.93

28

1160

1670

2410

2140

1300

1600

2000

2500

3000

3500

4000

4700

4700

5600

5600

6800

8100

23.16

25

1160

1670

2410

2410

25.63

22

1160

1670

2410

2820

28.36

21

1160

1670

2410

2360

31.39

18

1160

1670

2300

2780

34.74

17

1160

1670

2320

3060

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are based on a combination of the most
unfavorable conditions of loading. Values shown apply to high-speed shaft extensions on either side of the gear drive. Consult Factory for ratings of drives with fans and for speeds
higher than 1170 RPM.
Consult Factory for overhung load ratings.

Rexnord 2014

(131-110) 41

Overhung Loads
High-Speed Shaft
Type A, AR & AXV Overhung Loads (lb)
HighNominal
Speed
Ratio
Shaft RPM 4%

1170

870

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

Triple Reduction
Drive Size

Approx. LowSpeed Shaft


RPM

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

50
45
40
37
34
30
27
25
22
20
18
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1

920
920
920
930
930
930
940
940
940
940
940
940
950
950
940
940
950
950

920
920
920
930
930
930
940
930
940
940
940
940
950
950
940
940
950
950

930
930
940
880
940
880
900
900
910
910
910
910
910
920
920
920
920
920

930
930
940
880
940
880
900
910
910
910
910
910
910
920
920
920
920
920

1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590

1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590

1210
1210
1210
1210
1210
1210
1210
1590
1590
1620
1620
1620
1620
1620
1590
1590
1590
1590

1210
1210
1210
1210
1210
1210
1210
1590
1590
1620
1620
1620
1620
1620
1590
1590
1590
1590

900
900
900
900
900
900
900
900
900
900
900
900
900
900
900

900
900
900
900
900
900
900
900
900
900
900
900
900
900
900

1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200

1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200

1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600

1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600

2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000

2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000

2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500

2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500

2840
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000

3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000

2410
2040
3500
3500
3500
2940
3500
3500
3500
3500
3500
3500
3500
3500

2030
2970
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

3090
3340
3860
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

1780
1780
2390
770
2100
430
2720
4030
3330
4800
4800
4800
4800
4800
4800
4800

1950
1950
2620
1350
3620
2230
4630
4800
4800
4800
4800
4800
4800
4800
4800
4800

5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700

5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700

6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800

6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are based on a combination of the most
unfavorable conditions of loading. Values shown apply to high-speed shaft extensions on either side of the gear drive. Consult Factory for ratings of drives with fans and for speeds
higher than 1170 RPM.
Consult Factory for overhung load ratings.

42 (131-110)

Rexnord 2014

Overhung Loads
High-Speed Shaft
Type A, AR & AXV Overhung Loads (lb)
HighNominal
Speed
Ratio
Shaft RPM 4%

720

580

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

Triple Reduction
Drive Size

Approx. LowSpeed Shaft


RPM

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7

920
920
920
930
930
930
940
930
940
940
940
940
950
950
940
940
950
950

920
920
920
930
930
930
940
930
940
940
940
940
950
950
940
940
950
950

930
930
940
880
940
880
900
910
910
910
910
910
910
920
920
920
920
920

930
930
940
880
940
880
900
900
910
910
910
910
910
920
920
920
920
920

1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590

1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590
1590

1210
1210
1210
1210
1210
1210
1210
1590
1590
1620
1620
1620
1620
1620
1590
1590
1590
1590

1210
1210
1210
1210
1210
1210
1210
1590
1590
1620
1620
1620
1620
1620
1590
1590
1590
1590

900
900
900
900
900
900
900
900
900
900
900
900
900
900
900

900
900
900
900
900
900
900
900
900
900
900
900
900
900
900

1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200

1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200
1200

1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600

1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600

2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000

2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000

2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500

2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500

3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000

3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000

3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500

3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

2190
2190
3700
2730
4800
3540
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

3850
3850
4800
4390
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800
4800

5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700

5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700
5700

6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800

6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800
6800

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are based on a combination of the most
unfavorable conditions of loading. Values shown apply to high-speed shaft extensions on either side of the gear drive. Consult Factory for ratings of drives with fans and for speeds
higher than 1170 RPM.

Rexnord 2014

(131-110) 43

Overhung Loads
High-Speed Shaft
Type A, AR & AXV Overhung Loads (lb)
Nominal
Ratio
5%

Approx. LowSpeed Shaft


RPM

385

405

425

445

105.9
117.2
129.7 or Higher
105.9
117.2 or Higher

11.0
10.0
9.0 or Lower
8.3
7.5 or Lower

600
600
600
600
600

800
800

800

1000
1000

1000

1200
1200

1200

High-Speed
Shaft RPM

1170
870

Quadruple Reduction
Drive Size
465
485

1500
1500

1500

1700
1700

1700

505

525

535

555

2000
2000

2000

2300
2300

2300

2300
2300

2300

1850
3000

3000

Low-Speed Shaft
Type A Overhung Load Ratings (lb)
HighNominal
Speed
Ratio
Shaft RPM
3%

1750

1170

580

1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
5.60
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
5.60
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
5.60

Single Reduction
Drive Size

Approx. LowSpeed Shaft


RPM

305

325

345

365

385

405

425

445

465

485

505

525

950
860
780
700
640
575
520
470
420
380
350
310
640
575
520
470
420
380
350
310
280
255
230
210
320
290
260
235
210
190
175
155
140
130
115
105

3.21
3.15
3.17
3.17
3.15
3.17
3.21
3.17
3.21
3.33
3.52
3.56
3.02
2.95
2.98
2.97
2.95
2.98
3.01
2.98
3.07
3.29
3.49
3.54
3.02
2.92
2.77
2.68
2.77
2.81
2.88
2.92
3.02
3.25
3.46
3.50

5.64
5.82
6.04
6.25
6.56
6.79
7.03
7.24
7.53
7.89
7.96
7.96
6.36
6.57
6.82
7.05
7.40
7.66
7.75
7.75
7.73
7.75
7.90
7.92
7.74
7.65
7.52
7.41
7.34
7.51
7.35
7.40
7.55
7.69
7.86
7.87

5.72
5.94
6.15
6.38
6.63
6.98
7.22
7.44
7.72
8.07
8.70
9.11
6.75
6.88
6.93
7.20
7.49
8.13
8.14
8.39
8.71
9.11
10.1
10.5
9.02
9.20
9.25
9.42
9.69
10.6
10.4
10.8
11.0
11.5
11.6
11.7

7.98
8.34
8.74
8.96
9.32
9.68
9.95
10.4
10.8
11.3
11.7
12.1
9.00
9.41
9.86
10.1
10.5
10.9
11.2
11.8
12.1
12.1
12.0
12.1
11.7
11.7
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.7
11.9
12.1

12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5

12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5

10.8
11.3
9.86
10.3
10.4
11.7
11.4
12.4
12.5
12.5
12.5

6.08
6.60
7.24
7.96
8.14
8.93
8.45
9.40
11.6
12.2
13.9

6.86
7.45
8.17
8.99
9.18
10.1
10.5
11.5
14.1
14.7
15.0

8.47
9.20
10.1
11.1
12.4
13.1
15.0
15.0
15.0
15.0
15.0

2.74
3.88
5.24
6.50
6.79
7.44
7.97
9.27
10.3
12.1

3.10
4.38
5.91
7.33
7.67
8.40
9.28
12.0
13.1
14.9

6.84
3.82
7.93
8.40
9.96
10.9
12.6
14.1
17.2
18.0
18.0

10.00
11.6
12.8
14.6
17.0
17.5
18.8
19.6
20.3
21.2
22.7

11.3
13.1
14.5
16.5
19.2
19.8
21.2
22.1
22.9
23.9
25.0

18.2
16.2
17.8
20.4
24.0
24.8
25.0
25.0
25.0
25.0
25.0

2.45
5.91
8.51
10.6
11.9
12.9
13.8
15.1
16.8
18.0
18.8

2.75
6.67
9.60
12.0
13.5
14.5
15.6
17.0
19.0
20.3
21.2

3.41
8.22
12.2
14.8
16.6
17.9
19.2
21.0
23.4
30.7
31.9

3.88
6.81
11.6
14.4
20.1
23.6
25.0

4.38
7.68
13.1
18.1
22.7
28.0
31.6

3.72

5.41
9.48
34.2
37.8
37.7
40.0
40.0

2.88
7.11
12.7
19.8
24.0
29.5

3.25
8.04
14.3
22.4
27.5
38.7

8.06

3.98
9.94
34.1
38.5
44.2
50.0

7.18
9.31
12.0
13.5
15.9
16.7
18.8
21.3
25.0
26.6
37.0

8.10
10.5
13.6
15.2
17.9
18.8
21.2
24.0
30.9
33.2
48.5

10.0
13.0
17.0
19.9
22.1
23.3
26.2
31.0
52.2
54.6
60.0

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are based on a combination of the most
unfavorable conditions of loading. Values shown apply to high-speed shaft extensions on either side of the gear drive. Consult Factory for ratings of drives with fans.
Published ratings are for standard assemblies with shaft extensions as shown on page16 and are based on the most unfavorable conditions of loading. Interpolate for speeds
between those shown. For speeds below 580 RPM use ratings for 580 RPM.
Multiply values below by 1000.
Consult Factory for overhung load ratings.

44 (131-110)

Rexnord 2014

Overhung Loads
Low-Speed Shaft
Type A Overhung Load Ratings (lb)
Approx. LowSpeed Shaft
RPM

305

325

345

365

310
280
255
230
210
190
170
155
140
125
110
100
93
84
77
70
62
57 or Lower

3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16
3.16

7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45
7.45

9.09
9.17
9.25
9.55
9.82
10.2
10.4
10.8
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2

11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2
11.2

385

Double, Triple & Quadruple Reduction


Drive Size
405
425
445
465
485

505

525

545

565

585

12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5

15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0

29.4
30.1
30.2
31.0
32.1
32.9
33.9
35.0
37.2
37.0
38.2
39.6
40.4
42.6
43.1
45.0
47.3
50.0

41.6
45.4
44.1
48.1
46.9
51.1
49.8
51.3
57.0
57.5
57.5
60.0
60.0
60.0
60.0
60.0
60.0
60.0

49.0
50.6
51.3
53.2
54.5
56.3
57.9
59.8
61.3
62.0
65.6
65.9
69.4
70.0
72.0
72.0
72.0
72.0

70.9
69.0
75.1
72.3
74.4
75.4
77.6
80.2
92.1
85.1
86.0
86.0
86.0
86.0
86.0
86.0
86.0
86.0

68.4
68.6
72.7
72.9
77.2
77.4
83.8
81.9
84.6
87.7
92.3
93.1
98.0
98.9
100
100
100
100

15.6
15.8
15.9
16.8
16.9
17.8
17.9
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0

20.8
21.8
22.1
22.9
23.4
24.1
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0

20.6
21.4
21.8
22.8
23.2
24.2
24.6
25.4
26.4
26.9
28.0
28.7
29.9
31.8
31.6
33.0
33.0
33.0

32.1
34.9
34.1
36.9
36.2
39.2
38.3
39.6
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0

Published ratings are for standard assemblies with shaft extensions as shown on page16 and are based on the most unfavorable conditions of loading. Ratings are for a maximum
input speed of 1750 RPM. Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional
to torque (i.e., pinion, sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation.
Multiply values below by 1000.

Low-Speed Shaft Overhung Load

Low-Speed Shaft Overhung Load

Type AXVU Shaft Up (lb)

Type AXVU Shaft Down (lb)

Approx. LowSpeed Shaft


RPM

405

425

445

465

485

505

535

555

Approx. LowSpeed Shaft


RPM

405

425

445

465

485

505

535

555

310
280
255
230
210
190
170
155
140
125
110
100
93
84
77
70
62
57
50
46 or Lower

10.2
10.4
10.7
11.0
11.4
11.7
12.1
12.4
12.8
13.5
13.9
14.8
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0

9.85
9.73
9.36
10.3
9.94
10.8
10.4
10.4
10.2
11.3
11.7
12.9
13.0
13.9
15.0
15.9
17.1
18.0
18.0
18.0

14.2
15.0
15.1
15.8
16.0
16.8
17.3
17.5
18.2
18.5
19.3
20.1
20.5
21.3
21.5
22.4
23.1
23.4
24.3
25.0

18.0
18.8
19.2
19.9
20.3
21.2
21.5
22.2
23.1
23.5
24.5
25.1
26.1
27.7
27.7
29.4
29.5
31.3
33.0
33.0

20.9
21.9
22.2
23.1
23.5
24.5
24.9
25.7
27.0
27.2
28.5
29.1
30.1
30.8
31.0
33.3
33.5
36.1
39.2
40.0

27.8
29.3
29.1
30.3
30.6
32.2
32.4
34.2
34.5
36.8
36.6
39.0
39.6
40.0
42.2
43.4
45.9
47.6
50.0
50.0

37.5
38.1
39.0
40.5
41.4
42.2
44.0
44.8
46.5
47.6
49.8
50.3
52.0
54.3
55.0
57.6
58.7
60.0
60.0
60.0

57.3
58.2
60.9
61.7
64.7
65.5
68.9
69.5
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0

310
280
255
230
210
190
170
155
140
125
110
100
93
84
77
70
62
57
50
46 or Lower

15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0

15.6
15.8
15.9
16.8
16.9
17.8
17.9
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0

20.8
21.8
22.1
22.9
23.4
24.1
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0

26.2
27.0
27.0
28.7
29.6
30.4
31.3
32.2
33.0
33.0
33.0
33.0
33.0
33.0
33.0
33.0
33.0
33.0
33.0
33.0

32.4
33.9
34.4
36.0
36.5
38.2
38.6
39.9
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0

42.2
43.7
44.9
45.9
47.6
48.8
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0

35.2
33.9
36.3
35.8
38.5
37.1
40.9
39.4
41.8
41.8
44.2
44.3
45.7
50.5
48.4
52.1
51.6
55.4
59.6
60.0

72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0

Drive Size

Drive Size

Overhung load values listed are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e., pinion,
sprocket or sheave applications) an appropriate service factor must be considered in the overhung load calculation. Published ratings are for shaft extension as shown and are based
on the most unfavorable conditions of loading. Ratings are for a maximum input speed of 1750 RPM.

Rexnord 2014

(131-110) 45

Low-Speed Shaft Thrust Capacity


Type AXV Shaft Up or Down
Thrust Down (lb)

Thrust Up (lb)
Approx. LowSpeed Shaft
RPM

405

425

445

465

485

505

535

555

Approx. LowSpeed Shaft


RPM

405

425

445

465

485

505

535

555

310

11.5

13.0

13.5

16.8

20.4

25.4

28.8

60.0

310

11.2

12.6

13.1

16.3

19.7

24.6

50.0

57.4

280

11.5

12.9

14.1

17.5

22.2

26.9

27.9

60.0

280

11.5

12.4

13.7

17.1

21.5

26.1

50.0

58.4

255

11.5

12.5

14.3

17.8

21.6

27.0

29.5

60.0

255

11.5

12.0

13.9

17.3

20.9

26.1

50.0

60.0

230

11.5

13.7

14.8

18.6

23.5

27.7

29.6

60.0

230

11.5

13.2

14.3

18.1

22.7

26.8

50.0

60.0

210

11.5

13.3

15.0

18.9

23.0

28.7

31.4

60.0

210

11.5

12.7

14.6

18.4

24.7

27.7

50.0

60.0

190

11.5

14.4

15.6

19.8

24.9

29.4

30.5

60.0

190

11.5

13.9

15.2

19.2

24.1

28.5

50.0

60.0

170

11.5

14.0

16.0

20.0

24.3

33.5

33.3

60.0

170

11.5

15.3

15.5

19.5

23.5

32.3

50.0

60.0

155

11.5

14.4

16.6

20.7

23.1

31.3

32.4

60.0

155

11.5

13.8

16.1

20.1

24.3

30.3

50.0

60.0

140

11.5

15.2

16.7

21.6

27.4

33.2

34.5

60.0

140

11.5

14.5

16.3

21.7

26.5

32.2

50.0

60.0

125

11.5

16.4

17.4

21.9

26.6

33.7

34.4

60.0

125

11.5

15.7

17.0

21.3

25.7

32.1

50.0

60.0

110

11.5

16.5

17.8

22.9

28.4

34.2

36.5

60.0

110

11.5

16.5

17.2

22.3

28.0

33.1

50.0

60.0

100

11.5

16.5

18.5

23.6

29.6

35.8

36.4

60.0

100

11.5

16.5

18.0

23.0

27.4

34.7

50.0

60.0

93

11.5

16.5

18.9

24.4

30.0

36.2

37.6

60.0

93

11.5

16.5

18.3

23.7

29.6

35.0

50.0

60.0

84

11.5

16.5

19.6

25.0

30.0

38.0

41.1

60.0

84

11.5

16.5

19.0

25.0

30.0

36.9

50.0

60.0

77

11.5

16.5

20.0

25.0

30.0

38.6

39.8

60.0

77

11.5

16.5

19.4

25.0

30.0

37.4

50.0

60.0

70

11.5

16.5

20.6

25.0

30.0

40.0

43.1

60.0

70

11.5

16.5

20.0

25.0

30.0

40.0

50.0

60.0

62

11.5

16.5

21.0

25.0

30.0

40.0

42.5

60.0

62

11.5

16.5

20.6

25.0

30.0

40.0

50.0

60.0

57

11.5

16.5

21.0

25.0

30.0

40.0

45.8

60.0

57 or Lower

11.5

16.5

21.0

25.0

30.0

40.0

50.0

60.0

50

11.5

16.5

21.0

25.0

30.0

40.0

49.0

60.0

46 or Lower

11.5

16.5

21.0

25.0

30.0

40.0

50.0

60.0

Drive Size

Drive Size

Multiply values below by 1000.


Published ratings are based on a combination of the most unfavorable conditions of loading. For higher ratings, refer full data to the Factory. Consult the Factory for combined radial
and thrust loads. Ratings are for a maximum input speed of 1750 RPM.

46 (131-110)

Rexnord 2014

Exact Ratios/Parallel Shaft Gear Drives


Single Reduction Exact Ratios (Type A)
Drive Size

Nominal
Ratio

305

325

345

365

385

405

425

445

465

485

505

525

1.84

1.870

1.885

1.885

1.808

1.882

1.800

1.826

1.818

1.800

1.810

1.864

1.850

2.03

2.045

2.040

2.040

2.042

2.062

2.000

2.048

2.050

2.043

2.053

2.059

2.053

2.25

2.300

2.261

2.261

2.318

2.211

2.294

2.250

2.211

2.227

2.238

2.316

2.286

2.49

2.474

2.455

2.455

2.476

2.529

2.500

2.421

2.529

2.450

2.450

2.500

2.450

2.76

2.722

2.800

2.750

2.789

2.812

2.733

2.824

2.800

2.684

2.778

2.706

2.833

3.05

3.125

3.053

3.053

3.056

3.118

3.000

3.000

3.000

3.059

3.000

3.133

3.000

3.38

3.400

3.412

3.412

3.294

3.286

3.250

3.333

3.471

3.312

3.389

3.429

3.250

3.74

3.714

3.687

3.687

3.800

3.667

3.600

3.643

3.750

3.667

3.647

3.687

3.600

4.13

4.077

4.067

4.143

4.143

4.125

4.062

4.200

4.067

4.231

4.200

4.286

4.062

4.57

4.533

4.529

4.615

4.615

4.467

4.400

4.571

4.429

4.437

4.571

4.692

4.400

5.06

5.071

5.200

5.143

5.071

4.857

4.812

5.000

5.133

4.800

5.000

5.143

4.812

5.60

5.600

5.714

5.615

5.538

Except where noted with a footnote (), exact ratios are within 3% of the nominal ratios.
Double Reduction Exact Ratios (Type A, AR & AXV)
Drive Size
465
485

Nominal
Ratio

305

325

345

365

385

405

425

445

505

525

535

545

555

565

585

5.60

5.861

5.591

5.591

5.647

5.506

5.478

5.697

5.400

5.700

5.542

5.641

5.591

5.781

6.20

6.182

6.336

6.285

6.159

6.177

6.057

6.212 6.533 5.962

6.188

6.234 5.850 6.141

6.032

6.107

6.406

6.290

6.86

6.753

6.848

6.793

7.104

6.893

6.709

6.789

7.059

6.600

6.660

6.705

7.053

6.854

6.978

6.947

6.856

7.59

7.413

7.552

7.632

7.745

7.755

7.571

7.544

7.672

7.599

7.625

7.579 7.239 7.599

7.460

7.554

7.961

7.771

8.40

8.242

8.412

8.502

8.629

8.167

8.147

8.244

8.289

8.412

8.206

8.151

8.724

8.500

8.153

8.660

8.646

8.471

9.30

9.221

9.657

9.474

9.481

9.187

9.194

9.298

8.989

9.054

9.569

9.474

9.663

9.158

9.259

9.375

9.301

9.286

10.29

10.18

10.61

10.34

10.35

10.04

9.958

10.16

10.55

10.02

10.30

10.32 10.77 9.898

10.12

10.37

10.10

10.50

11.39

11.03

11.44

11.83

11.20

11.29

10.99

11.72

11.44

11.56

11.30 12.00 10.90 10.92 11.30

11.44

11.79

11.51

12.61

12.27

12.36

12.78

12.92

12.22 12.00 12.52

12.32 11.92 12.16

6.682

12.80 11.92 12.21

12.35

12.65

12.80

12.04

13.95

13.72

13.64

14.36

14.09

14.33

13.54

14.44 13.36 13.75

14.00

13.94

13.46

13.47

14.00

13.80

13.96

13.81

15.44

14.93

15.19

16.00

15.49

15.52

15.12

15.71

15.47

14.90

15.24

14.87

15.23

15.60

15.30

15.68

15.01

15.06

17.09

16.71

17.44

17.83

16.89

16.74

17.06

17.10

16.77

17.19

17.64

17.43

17.19

17.21

17.12

17.10

17.45

16.50

18.91

18.98

19.09

19.33

19.27 18.13 18.48

18.74

18.27 18.03 19.20

19.08

19.50

19.30

18.64

18.61

19.10

17.87

20.93

21.24

21.91

21.54

21.01 19.71 20.21

20.40

21.17 19.50 21.00

20.78

21.12

20.87

20.38

20.75

21.27

21.50

23.16

22.34

23.29

22.75

23.41

25.63

24.99

26.74

25.35

25.72

28.36

27.60

29.39

27.68

28.35

31.39

31.21

31.57

30.49

31.15

34.74

34.46

34.69

33.29

34.02

Except where noted with a footnote (), exact ratios are within 4% of the nominal ratios.
Availability of Types A / AR / AXV Double Reduction
Type

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

AR

AXV

Rexnord 2014

(131-110) 47

Exact Ratios/Parallel Shaft Gear Drives


Triple Reduction Exact Ratios (Type A, AR & AXV)
Nominal
Ratio

305

325

345

23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4

38.23
41.60
46.54
50.30
56.27
63.94
71.53
78.31
87.60
92.16
103.1
113.8
128.7
142.2
158.2
169.5
197.6
211.7

39.22
41.68
47.86
53.17
56.50
64.89
73.82
81.12
90.40
96.09
110.3
121.2
130.2
143.1
164.3
180.5
193.9
213.1

38.86
43.29
47.31
52.71
58.73
63.67
70.94
80.93
90.18
95.25
106.1
115.9
127.7
139.4
156.0
170.3
187.6
204.9

365

385

22.25

25.03

27.05

31.77

34.33
38.11
38.63
42.46
41.83
45.70 49.02
50.92
53.08
55.95
57.28
61.10
62.06
69.59
72.52
77.10
77.49
84.72 90.61
98.02
98.53
107.7

117.6

130.5

142.5

162.0

176.9

191.7

209.4

405

425

22.32
24.37
27.50
31.03
34.65
39.10
42.56
47.12
51.29
56.87
61.90
73.33
75.97
83.10
97.27
105.9

Drive Size
465

445

23.54
22.96
25.52
24.90
27.89
27.89
32.16
30.24
34.27 33.34
39.51
37.96
43.01
41.07
46.80
45.39
50.15
51.56
58.60
55.92
63.78 60.89
69.41
70.45
76.06
76.72
85.24
83.08
94.39
97.67
103.4
104.6

545

555

565

585

22.21
25.62
26.97
31.12
33.24
38.36
40.96
47.27
51.20
59.08
61.97
69.98
79.39
90.14
97.50
105.6

22.88
23.69
26.35
26.24
28.68
27.53
30.95
31.20
33.68
34.12
39.37
38.67
42.86
41.59
46.00
48.34
50.07
51.88
57.96
56.64
63.09
61.68
72.76
70.80
79.20
77.10
86.20
84.42
93.26 91.83
102.0 100.0

485

505

22.36
22.31
25.11
25.43
27.81
27.48
30.40
31.91
33.67
34.49
38.82
38.04
43.00
44.05
45.83
48.11
50.77
52.00
57.75
57.35
63.97
65.52
72.19
72.26
75.71
75.79
85.94
83.06
97.50
96.51
105.6 101.2

525

535

22.94
24.97
28.33
31.63
34.71
39.20
42.85
45.94
50.20
56.93
62.22
70.92
76.33
87.90
98.37
107.1

22.38
24.76
27.97
31.36
35.43
38.87
43.91
47.25
51.45
56.11
63.77
69.54
76.22
87.78
95.54
106.5

22.91
26.25
28.51
31.64
34.36
39.04
43.21
46.48
54.15
59.06
63.52
72.06
77.43
83.76
93.26
102.1

23.39
25.86
29.66
32.33
33.79
36.60
39.90
46.75
51.78
58.44
61.87
69.82
79.22
85.80
94.34
103.2

Except where noted with a footnote (), exact ratios are within 4% of the nominal ratios.
Availability of Types A / AR / AXV Triple Reduction
Type

305

325

345

365

385

405

425

445

465

485

505

525

535

545

555

565

585

A
AR
AXV

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

Quadruple Reduction Exact Ratios (Type A, AR & AXV)


Drive Size

Nominal
Ratio

385

405

425

445

465

485

505

525

535

555

105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
395.7
437.9

108.4
117.3
126.6
137.1
158.2
171.3
199.6
216.1
233.2
252.5
291.4
315.5
368.9
401.2

118.2
125.7
148.2
167.9
182.8
199.0
217.7
231.6
273.0
298.6
336.7
368.2
396.0
431.1

115.9
126.2
135.2
158.0
171.9
187.1
205.0
229.8
254.4
277.6
304.2
340.9
377.6
413.7

113.4
123.0
142.4
154.4
168.2
194.6
211.9
229.9
250.3
289.6
315.4
341.6
401.5
429.8

112.1
129.4
140.1
161.7
169.6
191.5
207.8
239.8
251.5
284.0
322.2
365.8
395.7
428.6

116.0
124.5
135.5
156.8
170.7
196.9
214.3
243.4
265.0
305.6
332.6
362.1
391.7
426.3

113.4
126.4
145.0
158.0
169.9
197.5
216.1
230.6
251.1
288.3
313.9
343.7
407.2
431.5

120.0
127.9
141.6
161.1
178.4
203.9
211.2
235.1
260.4
293.9
333.4
367.0
397.0
429.9

113.6
125.3
145.1
160.0
182.8
201.6
211.4
233.5
266.8
294.2
308.6
350.2
393.0
445.8

120.6
133.4
143.6
155.7
169.8
195.6
210.6
229.7
264.5
286.9
319.8
348.0
403.6
439.3

Except where noted with a footnote (), exact ratios are within 5% of the nominal ratios.
Availability of Types A / AR / AXV Quadruple Reduction
Type

385

405

425

445

465

485

505

525

535

555

A
AR
AXV

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

48 (131-110)

Rexnord 2014

Type A Single Reduction


Sizes 305-525
CAUTION: All (A1) Single reduction drive selections check for possible interference between the low-speed shaft connection and either the high-speed shaft extension or the guard for
the second high-speed shaft extension.
XX
SHAFT GUARD
(WHEN REQUIRED)

YB
T
YA
INSPECTION
COVER

W
D

C
1.2

E
BOTH ENDS
SIZES 385-525

V
R
Q

6-HOLES FOR
U DIA. BOLT

Q
M

SIZES 305-365

Dimensions (in)
Drive
Size

305
325
345
365
385
405
425
445
465
485
505
525

3.06
3.38
3.87
4.12
7.00
8.00
8.50
9.00
11.00
12.00
13.00
15.00

4.00
4.81
5.37
6.44
7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38

7.500
8.500
9.750
11.000
9.300
10.500
12.000
14.000
16.000
18.000
19.500
21.000

8.50
9.50
10.62
12.13
10.06
11.20
12.74
14.50
16.50
19.00
20.50
22.50

15.75
17.75
20.12
22.50
20.06
23.00
25.00
27.70
31.00
35.00
38.00
41.00

2.50
2.50
3.00
3.00
1.62
2.00
1.62
2.50
2.50
2.50
2.75
2.50

9.25
10.88
12.13
14.50
12.50
14.00
15.75
17.50
20.50
22.25
24.00
27.25

6.00
7.00
7.62
9.13
8.44
9.20
11.12
12.00
14.00
16.00
17.25
20.00

23.50
26.76
30.26
35.00
28.24
32.00
34.74
40.00
46.00
49.50
53.50
59.50

11.50
12.25
14.00
15.50
23.76
25.30
27.50
32.20
33.00
35.00
39.50
42.00

4.88
5.25
5.88
6.63
10.50
11.25
12.25
14.60
15.00
15.40
17.25
18.50

11.00
12.00
13.50
15.13
19.10
20.60
22.90
26.30
28.60
30.70
33.60
37.20

9.87
10.75
11.87
13.00
18.20
19.60
21.20
23.70
26.20
27.10
29.80
33.20

2.75
3.12
3.00
3.75
5.00
5.50
6.00
7.00
7.00
9.00
10.26
10.50

0.62
0.63
0.75
0.75
0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10

Drive
Size

Wt (lb)

305
325
345
365
385
405
425
445
465
485
505
525

440
560
780
1000
1340
1915
2640
3680
4780
6430
8440
11100

High-Speed Shaft
T

Key

2.000
2.125
2.375
2.750
3.500
4.000
4.250
4.500
5.500
6.000
6.500
7.500

0.500 x 0.500 x 3.000


0.500 x 0.500 x 3.500
0.625 x 0.625 x 3.750
0.625 x 0.625 x 4.000
0.875 x 0.875 x 6.000
1.000 x 1.000 x 7.000
1.000 x 1.000 x 7.500
1.000 x 1.000 x 8.000
1.250 x 1.250 x 10.000
1.500 x 1.500 x 11.000
1.500 x 1.500 x 12.000
1.750 x 1.500 x 13.000

Low-Speed Shaft
S

Key

2.750
3.000
3.500
4.000
4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500

0.625 x 0.625 x 4.000


0.750 x 0.750 x 4.500
0.875 x 0.875 x 5.000
1.000 x 1.000 x 6.000
1.000 x 1.000 x 6.500
1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000

XX

YA

YB

0.750
0.750
1.000
1.000
1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250

8.00
9.00
10.25
11.50
9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10

24.00
27.13
30.62
35.37
28.80
32.64
36.00
41.6
47.00
52.50
56.50
62.50

6.12
6.75
7.37
8.13
9.96
10.56
11.78
13.78
14.24
14.36
15.90
17.56

12.31
14.17
14.62
15.75
21.10
21.58
23.78
27.18
29.66
31.24
34.60
38.12

10.91
11.34
12.75
14.00
19.04
20.66
22.60
24.60
27.64
28.26
30.80
34.00

5.72
5.72
6.58
7.09
9.88
10.91
11.82
11.82
14.20
14.80
15.14
16.24

3.12
3.12
3.75
4.00
5.88
6.56
7.28
7.28
9.75
9.31
10.40
11.88

Drawings are representative of this series of drives and do not agree in exact detail for all sizes. Gear drives are for horizontal floor-mounted operation unless specifically stated
otherwise. Consult Factory for other mountings. Dimensions are for reference only and subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005. Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

Rexnord 2014

(131-110) 49

Type A Double Reduction


Sizes 305-585
XX
N

SHAFT GUARD
(WHEN REQUIRED)

B
S

INSPECTION
COVER
W
T

D
1.2

A
O

E
SIZES 305-365

BOTH ENDS
SIZES 385-585
J

6-HOLES FOR
U DIA. BOLT F

R
Q

G
K

Q
M

M
L

Dimensions (in)
Drive
Size

305
325
345
365
385
405
425
445
465
485
505
525
545
565
585

2.25
2.63
3.06
3.38
4.50
5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
13.00
13.00

4.00
4.81
5.37
6.44
7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38
20.12
21.44
22.76

12.187
14.125
16.000
18.500
15.800
17.700
20.200
23.300
26.500
30.000
33.500
37.000
41.000
44.500
49.000

8.50
9.50
10.62
12.13
10.24
11.20
12.74
14.50
16.50
19.00
20.50
22.50
24.50
25.50
29.00

Drive
Size

Wt (lb)

305
325
345
365
385
405
425
445
465
485
505
525
545
565
585

450
580
810
1090
1510
1850
2660
4030
5100
6300
9450
12140
17800
22800
31300

15.75 2.50
9.25
6.00
17.75 2.50
10.88
7.00
20.12 3.00
12.13
7.62
22.50 3.00
14.50
9.13
18.96 1.80
16.50
8.44
21.32 2.00
18.40
9.20
24.00 2.75
20.00 10.00
27.70 2.50
23.25 12.00
31.00 2.50
26.50 14.00
35.00 3.50 30.00 15.00
38.00 2.50 34.50 17.50
41.00 3.00 35.50 19.50
45.00 3.00
36.75 21.50
48.00 3.00
39.50 22.50
54.60 3.00
44.50 26.00
High-Speed Shaft

Key

1.250
1.500
1.750
2.000
2.250
2.500
3.000
3.500
4.000
4.500
5.000
5.500
6.000
6.500
6.500

0.250 x 0.250 x 2.500


0.375 x 0.375 x 2.750
0.375 x 0.375 x 3.000
0.500 x 0.500 x 3.500
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.000
0.750 x 0.750 x 5.000
0.875 x 0.875 x 6.000
1.000 x 1.000 x 7.000
1.000 x 1.000 x 8.000
1.250 x 1.250 x 9.000
1.250 x 1.250 x 10.000
1.500 x 1.500 x 11.000
1.500 x 1.500 x 12.000
1.500 x 1.500 x 12.000

23.50
26.76
30.26
35.00
36.60
40.80
45.50
51.50
58.00
58.50
65.00
71.00
79.50
85.00
95.00

11.50
12.25
14.00
15.50
21.00
22.80
24.80
27.40
29.00
33.00
37.00
39.00
44.00
52.00
56.40

4.88
5.25
5.88
6.63
9.10
10.00
11.00
12.20
13.00
14.40
16.00
17.00
19.50
23.20
25.40

11.00
12.00
13.50
15.13
17.80
19.40
21.60
23.90
26.60
30.70
33.60
37.20
41.90
45.40
49.80

9.12
9.88
10.87
12.12
14.10
15.20
17.20
19.30
21.20
23.00
25.60
27.40
32.60
35.70
38.60

2.75
3.12
3.00
3.75
5.00
5.50
6.00
7.00
7.00
8.00
8.80
9.00
9.15
11.50
11.50

0.62
0.63
0.75
0.75
0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10
2.10
2.35
2.35

Low-Speed Shaft
S

Key

2.750
3.000
3.500
4.000
4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500
11.500
12.250
13.000

0.625 x 0.625 x 4.000


0.750 x 0.750 x 4.500
0.875 x 0.875 x 5.000
1.000 x 1.000 x 6.000
1.000 x 1.000 x 6.500
1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000
3.000 x 2.000 x 17.000
3.000 x 2.000 x 19.000
3.000 x 2.000 x 21.000

XX

0.750
0.750
1.000
1.000
1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250
2.250
2.500
2.500

8.00
9.00
10.25
11.50
9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10
23.00
25.00
28.00

24.00
27.13
30.62
35.37
37.52
41.20
46.70
53.00
59.50
61.12
67.62
73.38
81.88
87.38
97.38

6.12
6.75
7.37
8.13
8.60
9.32
10.54
11.38
12.24
14.36
15.90
17.56
20.10
22.25
25.15

12.31
14.17
14.62
15.75
19.75
20.34
22.54
24.78
27.64
31.24
34.46
38.12
43.00
46.00
50.90

9.90
10.28
11.75
12.50
15.31
16.00
17.98
20.14
22.02
23.90
26.40
28.84
33.64
36.73
39.44

Drawings are representative of this series of drives and do not agree in exact detail for all sizes. Gear drives are for horizontal floor-mounted operation unless specifically stated
otherwise. Consult Factory for other mountings. Dimensions are for reference only and subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 485: high-speed end of drive Dimension G = 22.50", F = 2.50". Size 505: high-speed end of drive Dimension G = 25.50". Size 525: high-speed end of drive Dimension G =
29.50".

50 (131-110)

Rexnord 2014

Type A Triple Reduction


Sizes 305-585
XX
N

SHAFT GUARD
(WHEN REQUIRED)

INSPECTION
COVER

T
W

1.2

O
SIZES
305-365
E
V

BOTH ENDS
SIZES 385-585

R
Q

Q
M

6-HOLES FOR
U DIA. BOLT

M
L

8-HOLES FOR
U DIA. BOLT

G
F

AG

K
SIZES 545 thru 585

SIZES 305 thru 525

Dimensions (in)
Drive
Size

305
325
345
365
385
405
425
445
465
485
505
525
545
565
585

2.06
2.06
2.44
2.44
3.50
3.50
4.00
4.50
5.00
6.00
7.00
8.00
9.00
10.00
11.00

4.00
4.81
5.37
6.44
7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38
20.12
21.44
22.76

12.187
14.125
16.000
18.500
21.300
23.700
26.700
30.500
34.700
39.300
44.000
49.000
55.000
60.500
65.000

8.50
9.50
10.62
12.13
10.24
11.20
12.74
14.50
16.50
19.00
20.50
22.50
24.50
25.50
29.00

Drive
Size

Wt (lb)

305
325
345
365
385
405
425
445
465
485
505
525
545
565
585

450
580
820
1100
1520
1880
2460
4070
5200
7500
10100
13070
19300
25900
33400

15.75 2.50
9.25
17.75 2.50 10.88
20.12 3.00 12.13
22.50 3.00 14.50
18.96 1.80 16.50
21.32 2.00 18.40
24.00 2.75 20.00
27.70 2.50 23.25
31.00 2.50 26.50
35.00 3.50 30.00
38.00 2.50 34.50
41.00 3.00 37.25
45.00 3.00 23.50
48.00 3.00 26.50
54.60 3.00 28.00

6.00 23.50
7.00 26.76
7.62 30.26
9.13 35.00
8.44 36.60
9.20 40.80
10.00 45.50
12.00 51.50
14.00 58.00
15.00 66.00
17.50 74.30
19.50 80.50
21.50 89.50
22.50 99.50
26.00 108.00

High-Speed Shaft
T

Key

1.125
1.125
1.250
1.250
1.750
1.750
2.000
2.250
2.500
3.000
3.500
4.000
4.500
5.000
5.500

0.250 x 0.250 x 2.250


0.250 x 0.250 x 2.250
0.250 x 0.250 x 2.500
0.250 x 0.250 x 2.500
0.375 x 0.375 x 3.000
0.375 x 0.375 x 3.000
0.500 x 0.500 x 3.250
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.750 x 0.750 x 5.500
0.875 x 0.875 x 6.000
1.000 x 1.000 x 7.000
1.000 x 1.000 x 8.000
1.250 x 1.250 x 9.000
1.250 x 1.250 x 10.000

Low-Speed Shaft

11.50
12.25
14.00
15.50
21.00
22.80
24.80
27.40
29.00
33.00
37.00
39.00
44.00
52.00
56.40

4.88
5.25
5.88
6.63
9.10
10.00
11.00
12.20
13.00
14.40
16.00
17.00
19.50
23.20
25.40

11.00
12.00
13.50
15.13
17.80
19.40
21.60
23.90
26.60
30.70
33.60
37.20
41.90
45.40
49.80

8.75
9.12
10.12
10.87
12.80
13.60
15.10
16.60
17.80
19.80
22.30
24.20
29.40
33.00
36.20

2.75
3.12
3.00
3.75
5.00
5.50
6.00
7.00
7.00
8.00
8.80
9.00
9.15
11.50
11.50

0.62
0.63
0.75
0.75
0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10
2.10
2.35
2.35

AG

Key

2.750
3.000
3.500
4.000
4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500
11.500
12.250
13.000

0.625 x 0.625 x 4.000


0.750 x 0.750 x 4.500
0.875 x 0.875 x 5.000
1.000 x 1.000 x 6.000
1.000 x 1.000 x 6.500
1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000
3.000 x 2.000 x 17.000
3.000 x 2.000 x 19.000
3.000 x 2.000 x 21.000

36.50
40.50
46.00

XX

0.750
0.750
1.000
1.000
1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250
2.250
2.500
2.500

8.00
9.00
10.25
11.50
9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10
23.00
25.00
28.00

24.00
27.13
30.62
35.37
37.52
41.20
46.70
53.00
59.50
68.62
76.92
82.88
91.88
101.88
110.38

6.12
6.75
7.37
8.13
8.60
9.32
10.54
11.38
12.24
14.36
15.90
17.56
20.10
22.25
25.15

12.31
14.17
14.62
15.75
19.75
20.34
22.54
24.78
27.64
31.24
34.46
38.12
43.00
46.00
50.90

9.90
10.28
11.75
12.50
13.38
14.30
15.86
17.34
18.62
20.54
23.16
25.22
30.33
35.00
37.72

Drawings are representative of this series of drives and do not agree in exact detail for all sizes. Gear drives are for horizontal floor-mounted operation unless specifically stated
otherwise. Consult Factory for other mountings. Dimensions are for reference only and subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 485: high-speed end of drive Dimension F = 2.50". Size 505: high-speed end of drive Dimension F = 2.80".

Rexnord 2014

(131-110) 51

Type A Quadruple Reduction


Sizes 385-525
XX
N

SHAFT GUARD
(WHEN REQUIRED)

B
S

INSPECTION
COVER

T
W
C

1.2

E
Z

V
BOTH ENDS

R
Q

Q
M

6-HOLES FOR
U DIA. BOLT

Dimensions (in)
Drive
Size

385
405
425
445
465
485
505
525

3.00
3.00
3.00
3.50
3.50
4.50
5.50
6.00

7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38

21.300
23.700
26.700
30.500
34.700
39.300
44.000
49.000

10.24
11.20
12.74
14.50
16.50
19.00
20.50
22.50

Drive
Size

Wt (lb)

385
405
425
445
465
485
505
525

1560
1900
2760
4120
5300
7600
10250
13260

18.96 1.80
21.32 2.00
24.00 2.75
27.70 2.50
31.00 2.50
35.00 3.50
38.00 2.50
41.00 3.00

16.50
18.40
20.00
23.25
26.50
30.00
34.50
37.25

8.44
9.20
10.00
12.00
14.00
15.00
17.50
19.50

36.60
40.80
45.50
51.50
58.00
66.00
74.30
80.50

21.00
22.80
24.80
27.40
29.00
33.00
37.00
39.00

9.10
10.00
11.00
12.20
13.00
14.40
16.00
17.00

17.80
19.40
21.60
23.90
26.60
30.70
33.60
37.20

12.30
13.00
13.90
15.40
16.30
18.30
20.50
22.10

5.00
5.50
6.00
7.00
7.00
8.00
8.80
9.00

0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10

High-Speed Shaft
T

Key

1.500
1.500
1.500
1.750
1.750
2.250
2.750
3.000

0.375 x 0.375 x 2.500


0.375 x 0.375 x 2.750
0.375 x 0.375 x 2.500
0.375 x 0.375 x 3.000
0.375 x 0.375 x 3.000
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.750 x 0.750 x 5.000

Low-Speed Shaft
S

Key

4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500

1.000 x 1.000 x 6.500


1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000

XX

1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250

5.30
6.62
7.00
8.50
9.50
10.80
11.56
12.90

37.52
41.20
46.70
53.00
59.50
68.62
76.92
82.88

8.60
9.32
10.54
11.38
12.24
14.36
15.90
17.56

19.75
20.34
22.54
24.78
27.64
31.24
34.46
38.12

13.38
14.08
14.98
16.04
17.56
19.04
21.84
22.90

9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10

Drawings are representative of this series of drives and do not agree in exact detail for all sizes. Gear drives are for horizontal floor-mounted operation unless specifically stated
otherwise. Consult Factory for other mountings. Dimensions are for reference only and subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 485: high-speed end of drive Dimension F = 2.50". Size 505: high-speed end of drive Dimension F = 2.80".

52 (131-110)

Rexnord 2014

Type AR Double Reduction


Sizes 405-485
AH

B
UA

UA

W
C

INSPECTION
PLUG
(BOTH SIDES)
A
E
O

AE
CLEARANCE

2.8

L M

LA

LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

T
N

M
6-HOLES FOR
X DIA. BOLT
R

2.8

Dimensions (in)
Drive
Size

405
425

5.00

9.70

17.700

11.31

17.65

1.50

6.00

11.00

20.200

12.31

19.45

1.50

445

7.00

12.20

23.300

14.62

21.41

465

8.00

14.00

26.500

16.62

23.16

485

9.00

15.90

30.000

18.50

25.00

2.29

Drive
Size

Key

405

5.000

425

5.750

18.50

9.20

40.00

27.75

12.50

21.62

24.90

12.11

5.00

1.50

21.00

10.25

45.00

31.80

14.50

24.62

27.80

13.50

6.00

1.60

1.75

24.00

12.25

51.50

37.00

16.75

29.25

31.00

14.75

7.00

1.81

1.95

27.20

14.10

58.25

41.00

18.75

33.25

33.80

16.31

7.00

1.79

26.90

15.60

58.38

46.50

21.00

37.00

36.60

11.00

8.00

2.00

Low-Speed Shaft

High-Speed Shaft

AE

AH

0.625 x 0.625 x 4.000

42.45

1.125

41.12

25.4

0.750 x 0.750 x 5.000

47.22

1.250

46.01

28.2

UA

UB

UC

UD

Key

1.250 x 1.250 x 7.500

8.66

0.750

1.88

3.50

2.500

1.500 x 1.500 x 8.000

10.06

1.125

2.25

3.50

3.000

LA

Wt (lb)

29.10

5.7

2360

32.20

6.6

3094

445

6.500

1.500 x 1.500 x 10.000

11.38

1.250

2.50

4.00

3.500

0.875 x 0.875 x 6.000

53.75

1.500

52.67

32.9

35.60

6.7

4334

465

7.250

1.750 x 1.500 x 11.000

12.68

1.250

2.50

4.75

4.000

1.000 x 1.000 x 7.000

61.11

1.500

59.43

37.4

39.20

7.7

6500

485

8.000

2.000 x 1.500 x 12.000

14.00

1.500

3.00

5.00

4.500

1.000 x 1.000 x 8.000

60.81

2.000

59.50

40.7

43.10

9.4

8093

 Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

Rexnord 2014

(131-110) 53

Type AR Double Reduction


Sizes 505-555

AE
CLEARANCE

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

L M

T
N

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

G
K

Dimensions (in)
Drive
Size

AE

AH

GA

KA

505

10.00

43.7

47.62

17.32

33.500

19.62

27.87

27.00

13.50

64.62

18.88

50.50

22.75

39.25

535

11.00

52.2

52.00

19.50

39.000

22.62

30.00

31.75

16.50

74.25

21.75

56.50

25.75

45.25

555

12.00

56.4

59.30

21.80

43.000

24.62

34.95

35.00

10.00

18.00

81.75

23.75

61.50

28.25

49.25

Drive
Size

505

40.76

13.12

10.50

2.25

535

43.65

14.60

10.50

2.25

555

49.70

16.00

12.00

2.31

11.500

Low-Speed Shaft
S

High-Speed Shaft

Wt (lb)

1.250 x 1.250 x 9.00

2.250

66.25

11,850

1.250 x 1.250 x 10.00

2.250

76.22

16,100

2.250

83.62

22,650

Key

UA

UB

UC

UD

Key

9.250

2.500 x 1.750 x 14.00

16.18

1.500

3.00

6.00

5.000

10.500

2.500 x 1.750 x 16.00

18.38

1.500

3.00

7.50

5.500

3.000 x 2.000 x 17.00

20.12

1.750

3.50

8.00

6.000

1.500 x 1.500 x 11.00

Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Add 1.00" to dimensions K, KA, Y & D for Size 505ARJ drive.

54 (131-110)

Rexnord 2014

Type AR Triple Reduction


Sizes 405-485
AH

B
UA

UA

W
C

T
INSPECTION
PLUG
(BOTH SIDES)

A
E
O

AE
CLEARANCE

2.8

LA

LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE
L M
N

M
6-HOLES FOR
X DIA. BOLT
R

2.8

Dimensions (in)
Drive
Size

405
425

3.50

9.70

23.700

11.31

17.65

1.50

4.00

11.00

26.700

12.31

19.45

1.50

18.50

9.20

40.00

27.75

12.50

21.62

23.30

6.11

5.00

1.50

21.00

10.25

45.00

31.80

14.50

24.62

25.70

7.00

6.00

1.60

445

4.50

12.20

30.500

14.62

21.41

465

5.00

14.00

34.700

16.62

23.16

1.75

24.00

12.25

51.50

37.00

16.75

29.25

28.30

7.55

7.00

1.81

1.95

27.20

14.10

58.25

41.00

18.75

33.25

30.40

8.11

7.00

1.79

485

6.00

15.90

39.300

18.50

25.00

2.41

30.60

15.60

65.90

46.50

21.00

37.00

33.40

9.24

8.00

2.00

Drive
Size

Key

UA

UB

UC

UD

Key

405

5.000

1.250 x 1.250 x 7.500

8.66

.750

1.88

3.50

1.750

425

5.750

1.500 x 1.500 x 8.000

10.06

1.125

2.25

3.50

445

6.500

1.500 x 1.500 x 10.000

11.38

1.250

2.50

4.00

465

7.250

1.750 x 1.500 x 11.000

12.68

1.250

2.50

485

8.000

2.000 x 1.500 x 12.000

14.00

1.500

3.00

Low-Speed Shaft

High-Speed Shaft

AE

AH

LA

Wt (lb)

0.375 x 0.375 x 3.000

42.45

1.125

41.12

25.4

29.10

5.7

2393

2.000

0.500 x 0.500 x 3.250

47.22

1.250

46.01

28.2

32.20

6.6

3159

2.250

0.500 x 0.500 x 4.000

53.75

1.500

52.67

32.9

35.60

6.7

4424

4.75

2.500

0.625 x 0.625 x 4.500

61.11

1.500

59.43

37.4

39.20

7.7

6597

5.00

3.000

0.750 x 0.750 x 5.500

68.02

2.000

67.04

40.7

43.10

9.4

8820

 Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 485 low-speed end of drive Dimension F = 2.29.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

Rexnord 2014

(131-110) 55

Type AR Triple Reduction


Sizes 505-555
AH

S D

UA

S
UA

INSPECTION PLUG
(BOTH SIDES)
P

A
E
O

AE
CLEARANCE

GA

L M

3-HOLES EQUALLY SPACED


UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

T
N

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

G
K

KA

Dimensions (in)
Drive
Size

AE

AH

GA

KA

505

7.00

43.7

47.62

17.32

44.000

19.62

27.87

31.00

13.50

72.90

18.88

50.50

22.75

39.25

535

8.00

51.0

52.00

19.50

51.000

22.62

30.00

35.75

16.50

82.25

21.75

56.50

25.75

45.25

555

9.00

55.1

59.30

21.80

57.000

24.62

34.95

40.00

10.00

18.00

92.75

23.75

61.50

28.25

49.25

Drive
Size

505

37.46

10.90

10.50

2.25

535

40.45

10.98

10.50

2.25

555

46.54

13.00

12.00

2.31

11.500

Low-Speed Shaft
S

High-Speed Shaft

Wt (lb)

0.875 x 0.875 x 6.00

2.250

74.53

12,850

1.000 x 1.000 x 7.00

2.250

84.60

18,050

1.000 x 1.000 x 8.00

2.250

94.62

24,200

Key

UA

UB

UC

UD

Key

9.250

2.500 x 1.750 x 14.00

16.18

1.500

3.00

6.00

3.500

10.500

2.500 x 1.750 x 16.00

18.38

1.500

3.00

7.50

4.000

3.000 x 2.000 x 17.00

20.12

1.750

3.50

8.00

4.500

Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Add 1.00" to dimensions K, KA, Y & D for Size 505ARJ drive.

56 (131-110)

Rexnord 2014

Type AR Quadruple Reduction


Sizes 405-485
AH

B
UA

UA

W
C

INSPECTION
PLUG
(BOTH SIDES)

A
E
O

AE
CLEARANCE

2.8

LA

LA

L M

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE
Z

M
T

6-HOLES FOR
X DIA. BOLT

2.8

Dimensions (in)
Drive
Size

405

3.00

9.70

23.700

11.31

17.65

1.50

18.50

9.20

40.00

27.75

12.50

21.62

22.70

6.11

5.00

1.50

425

3.00

11.00

26.700

12.31

19.45

1.50

21.00

10.25

45.00

31.80

14.50

24.62

24.50

7.00

6.00

1.60

445

3.50

12.20

30.500

14.62

21.41

1.75

24.00

12.25

51.50

37.00

16.75

29.25

27.10

7.55

7.00

1.81

465

3.50

14.00

34.700

16.62

23.16

1.95

27.20

14.10

58.25

41.00

18.75

33.25

28.90

8.11

7.00

1.79

485

4.50

15.90

39.300

18.50

25.00

2.41

30.60

15.60

65.90

46.50

21.00

37.00

31.90

9.24

8.00

2.00

Low-Speed Shaft

Drive
Size

Key

405

5.000

425

5.750

High-Speed Shaft
T

Key

AE
Assys Assys
1, 3 & 5 2, 4 & 6

AH

LA

Wt (lb)

25.4

29.10

5.7

2375

28.2

32.20 6.6

3159

26.8

32.9

35.60

6.7

4495

30.9

37.4

39.20

7.7

6752

33.3

40.7

43.10 9.4

UA

UB

UC

UD

1.250 x 1.250 x 7.500

8.66

0.750

1.88

3.50

1.500 0.375 x .0375 x 2.750 42.45 1.125 41.12 4.500

21.5

1.500 x 1.500 x 8.000

10.06

1.125

2.25

3.50

1.500 0.375 x 0.375 x 2.500 47.22 1.250 46.01 5.500

23.1

445

6.500 1.500 x 1.500 x 10.000 11.38

1.250

2.50

4.00

1.750 0.375 x 0.375 x 3.000 53.75 1.500 52.67 6.000

465

7.250 1.750 x 1.500 x 11.000 12.68

1.250

2.50

4.75

1.750 0.375 x 0.375 x 3.000 61.11 1.500 59.43 6.500

485

8.000 2.000 x 1.500 x 12.000 14.00

1.500

3.00

5.00

2.250 0.500 x 0.500 x 4.000 68.02 2.000 67.04 7.200

8960

 Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 485 low-speed end of drive Dimension F = 2.29.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

Rexnord 2014

(131-110) 57

Type AR Quadruple Reduction


Sizes 505-555
AH

S D

UA

S
UA

INSPECTION PLUG
(BOTH SIDES)
P

A
E
O

AE
CLEARANCE

GA
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

L M

M
T
GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

G
K

KA

Dimensions (in)
Drive
Size

505

5.38

AE
Assys
Assys
1, 3 & 5 2, 4 & 6

35.6

43.7

AH

GA

KA

47.62

17.32

44.000

19.62

27.87

31.00

13.50

72.90

18.88

50.50

22.75

39.25

535

6.00

42.0

50.4

52.00

19.50

51.000

22.62

30.00

35.75

16.50

82.25

21.75

56.50

25.75

45.25

555

6.00

44.8

55.1

59.30

21.80

57.000

24.62

34.95

40.00

10.00

18.00

92.75

23.75

61.50

28.25

49.25

Drive
Size

505 35.66

10.90

10.50

Low-Speed Shaft

High-Speed Shaft

Wt (lb)

0.625 x 0.625 x 4.50

2.250

74.53

8.20

13,000

Key

UA

UB

UC

UD

Key

2.25

9.250

2.500 x 1.750 x 14.00

16.18

1.500

3.00

6.00

2.750

535

38.35

10.98

10.50

2.25

10.500

2.500 x 1.750 x 16.00

18.38

1.500

3.00

7.50

3.000

0.750 x 0.750 x 5.00

2.250

84.60

8.20

18,200

555

43.33

13.00

12.00

2.31

11.500

3.000 x 2.000 x 17.00

20.12

1.750

3.50

8.00

3.000

0.750 x 0.750 x 5.00

2.250

94.62

9.30

23,950

Gear drives are for horizontal output shaft operation with housing side walls horizontal unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Add 1.00" to dimensions K, KA, Y & D for Size 505ARJ drive.
For assemblies 1, 3 & 5, high-speed shaft is above centerline of drive.

58 (131-110)

Rexnord 2014

Type ARJ Double, Triple & Quadruple Reduction


Hollow Low-Speed Shaft Shrink Disc Mounted
Refer to pages50-58 for basic gear drive dimensions. Refer to page112 for hollow low-speed shaft dimensions and driven shaft recommendations and dimensions.
SHAFT GUARD

SHAFT GUARD

SHRINK DISC

SHRINK DISC
AJ

AJ
AL
UE
U

AL
U

AC REQUIRED FOR TORQUE


WRENCH CLEARANCE
AG

AF
AD

AC REQUIRED FOR TORQUE


WRENCH CLEARANCE

MINIMUM CLEARANCE
REQUIRED FOR REMOVAL
OF SHAFT GUARD

AF

AG
AD

SIZES 405-485

MINIMUM CLEARANCE
REQUIRED FOR REMOVAL
OF SHAFT GUARD

SIZES 505-555

Dimensions (in)
Drive
Size

U
+.002
-.000

UE

AJ

AC

AD

AF

AG

AL

405

5.500

5.2505

4.00

26.51

1.20

31.96

425

6.250

6.0005

4.00

29.91

1.70

445

6.750

6.5005

5.00

33.33

1.50

465

7.500

7.2505

5.00

35.60

485

8.750

8.5005

5.00

38.89

505

10.000

24.12

9.7505

5.00

535

10.750

24.12

10.5005

555

11.750

26.25

11.4005

Wt (lb)
Double

Triple

Quad

16.72

2,360

2,390

2,375

37.95

17.96

3,095

3,160

3,160

42.27

19.83

4,330

4,420

4,495

1.50

45.16

21.33

6,500

6,595

6,750

1.40

49.94

24.62

8,073

8,800

8,940

42.55

4.17

56.10

24.33

11,650

12,800

12,950

5.00

45.80

1.12

59.90

55.58

15,850

17,850

17,950

5.50

52.00

2.20

67.00

27.58

22,000

23,500

23,250

Dimensions are for reference only and are subject to change without notice unless certified.
Sizes 405-465, tolerance is +.0016, -.0000; Size 485, tolerance is +.0020, -.0000.

Rexnord 2014

(131-110) 59

Type AXV & AXVQ Double Reduction


Sizes 405-485
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
Y
LA

LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

AE
CLEARANCE

D
SHAFT
COVER

AD

6-HOLES FOR
X DIA. BOLT

J
F

BEARING
GREASE
FITTING

K
W

H
C

AE
CLEARANCE

2.8
HA

BA

UE

2.8
HB
HA

UA

HB

AH
O
E

HC

HC

HD
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

HD

Q
M

SIZE 405

L
SIZES 425-485

Dimensions (in)
Drive
Size

Lubrication System

HA

HB

HC

HD

405

5.00

9.70 17.700 11.31 17.65

1.50

18.50

7.47

12.71 10.88 19.99

1.25

9.20

40.00 27.75 12.50 21.62 24.90 12.11

5.00

1.50

425

6.00

11.00 20.200 12.31 19.45

1.50

21.00

7.65

13.19 10.03 19.57

1.35

10.25 45.00 31.80 14.50 24.62 27.80 13.50

6.00

1.60

445

7.00

12.20 23.300 14.62 21.41

1.75

24.00

9.92

16.88 12.09 21.42

1.18

12.25 51.50 37.00 16.75 29.25 31.00 14.50

7.00

1.81

465

8.00

14.00 26.500 16.62 23.16 1.95 27.20

9.92

18.88 13.34 23.20

1.42

14.10 58.25 41.00 18.75 33.25 33.80 16.31

7.00

1.79

485

9.00

15.90 30.000 18.50 25.00

9.92

18.88 15.09 24.97

1.87

15.60 58.38 46.50 21.00 37.00 36.60 11.00

8.00

2.00

Drive
Size

2.29

26.90

Low-Speed Shaft
S

Key

UA

UB

UC

UD

Hollow Low-Speed Shaft


U
UE
+.002 +.000
Keyway
- .000 - .005

High-Speed Shaft
T

Key

AD

AE

AH

BA

405 5.000 1.250 x 1.250 x 7.500 8.66 0.750 1.88 3.50 5.375 15.249 1.000 x 0.312 2.500 0.625 x 0.625 x 4.000 42.45 1.125 41.12 21.34 30.6 29.10 4.50

LA

Wt
(lb)

5.7 2460

425 5.750 1.500 x 1.500 x 8.000 10.06 1.125 2.25 3.50 6.000 15.749 1.500 x 0.265 3.000 0.750 x 0.750 x 5.000 47.22 1.250 46.01 23.50 33.5 32.20 4.00 6.6 3191
445 6.500 1.500 x 1.500 x 10.000 11.38 1.250 2.50 4.00 6.750 18.499 1.500 x 0.510 3.500 0.875 x 0.875 x 6.000 53.75 1.500 52.67 25.50 36.4 35.60 4.60

6.7 4455

465 7.250 1.750 x 1.500 x 11.000 12.68 1.250 2.50 4.75 7.500 20.999 1.500 x 0.510 4.000 1.000 x 1.000 x 7.000 61.11 1.500 59.43 27.23 39.2 39.20 4.60

7.7 6627

485 8.000 2.000 x 1.500 x 12.000 14.00 1.500 3.00 5.00 8.500 23.749 1.500 x 0.510 4.500 1.000 x 1.000 x 8.000 60.81 2.000 59.50 29.18 41.9 43.10 5.40 9.4 8220
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

60 (131-110)

Rexnord 2014

Type AXV & AXVQ Double Reduction


Sizes 505-555
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

Y
GA

AE
CLEARANCE

D
SHAFT
COVER

AD

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

AE
CLEARANCE

BA

UE

KA

BEARING
GREASE
FITTING

N
HA

HB

UA

AH
O
E

HC
R

HD

BEARING
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

Q
M

Dimensions (in)
Drive
Size

AD

AE

AH

BA

GA

Lubrication System
H

HA

HB

HC

HD

KA

505

10.00 33.06

47.1

47.62 17.32

6.80 33.500 19.62 27.87 27.00

9.91

16.82 16.34 27.67

2.80

13.50 64.62 18.88 50.50 22.75

535

11.00 35.18

50.8

52.00 19.50

6.80 39.000 22.62 30.00 31.75

9.91

20.00 18.84 29.68

3.05

16.50 74.25 21.75 56.50 25.75

555

12.00 40.39

58.5

59.30 21.80

6.60 43.000 24.62 34.95 35.00 10.00

9.91

20.00 20.84 34.51

3.41

18.00 81.75 23.75 61.50 28.25

Drive
Size

Low-Speed Shaft
N

Key

UA

UB

UC

UD

Keyed Hollow
Low-Speed Shaft
U
UE
+.002 +.000
Keyway
- .000 - .005

Wt (lb)

High-Speed Shaft
T

Key

AXV

AXVQ

505 39.25 40.76 13.12 10.50 2.25 9.250 2.500 x 1.750 x 14.00 16.18 1.500 3.00 6.00 9.001 24.999 2.000 x 0.510 5.000 1.250 x 1.250 x 9.00 2.250 66.25 11,900 11,950
535 45.25 43.65 14.60 10.50 2.25 10.500 2.500 x 1.750 x 16.00 18.38 1.500 3.00 7.50 10.501 27.999 2.500 x 0.760 5.500 1.250 x 1.250 x 10.00 2.250 76.22 16,200 16,100
555 49.25 49.70 16.00 12.00 2.31 11.500 3.000 x 2.000 x 17.00 20.12 1.750 3.50 8.00 11.501 28.999 3.000 x 0.760 6.000 1.500 x 1.500 x 11.00 2.250 83.62 22,800 22,400
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

Rexnord 2014

(131-110) 61

Type AXV & AXVQ Triple Reduction


Sizes 405-485
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
Y
LA

LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

AE
CLEARANCE

D
SHAFT
COVER

AD

6-HOLES FOR
X DIA. BOLT

J
F

BEARING
GREASE
FITTING

AE
CLEARANCE

D
S

2.8
HA

BA

UE

2.8
HB
HA

UA

HB

AH
O
E

HC

HC

HD
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

HD

Q
M

SIZE 405

L
SIZES 425-485

Dimensions (in)
Drive
Size

405

3.50

9.70 23.700 11.31 17.65

Lubrication System

1.50

18.50

7.47

HA

HB

HC

12.71 10.88 19.99

HD

1.25

9.20

40.00 27.75 12.50 21.62 23.30

6.11

5.00

1.50

425

4.00

11.00 26.700 12.31 19.45

1.50

21.00

7.65

13.19 10.03 19.57

1.35

10.25 45.00 31.80 14.50 24.62 25.70

7.00

6.00

1.60

445

4.50

12.20 30.500 14.62 21.41

1.75

24.00

9.92

16.88 12.09 21.42

1.18

12.25 51.50 37.00 16.75 29.25 28.30

7.55

7.00

1.81

465

5.00

14.00 34.700 16.62 23.16 1.95 27.20

9.92

18.88 13.34 23.20

1.42

14.10 58.25 41.00 18.75 33.25 30.40

8.11

7.00

1.79

485

6.00

15.90 39.300 18.50 25.00 2.41 30.60

9.92

18.88 15.09 24.97

1.87

15.60 65.90 46.50 21.00 37.00 33.40

9.24

8.00

2.00

Drive
Size

Low-Speed Shaft
S

Key

UA

UB

UC

UD

Hollow Low-Speed Shaft


U
UE
+.002 +.000
Keyway
- .000 - .005

High-Speed Shaft
T

Key

AD

AE

AH

BA

405 5.000 1.250 x 1.250 x 7.500 8.66 0.750 1.88 3.50 5.375 15.249 1.000 x 0.312 1.750 0.375 x 0.375 x 3.000 42.45 1.125 41.12 21.34 30.6 29.10 4.50

LA

Wt
(lb)

5.7 2493

425 5.750 1.500 x 1.500 x 8.000 10.06 1.125 2.25 3.50 6.000 15.749 1.500 x 0.265 2.000 0.500 x 0.500 x 3.250 47.22 1.250 46.01 23.50 33.5 32.20 4.00 6.6 3256
445 6.500 1.500 x 1.500 x 10.000 11.38 1.250 2.50 4.00 6.750 18.499 1.500 x 0.510 2.250 0.500 x 0.500 x 4.000 53.75 1.500 52.67 25.50 36.4 35.60 4.60

6.7 4545

465 7.250 1.750 x 1.500 x 11.000 12.68 1.250 2.50 4.75 7.500 20.999 1.500 x 0.510 2.500 0.625 x 0.625 x 4.500 61.11 1.500 59.43 27.23 39.2 39.20 4.60

7.7 6724

485 8.000 2.000 x 1.500 x 12.000 14.00 1.500 3.00 5.00 8.500 23.749 1.500 x 0.510 3.000 0.750 x 0.750 x 5.500 68.02 2.000 67.04 29.18 41.9 43.10 5.40 9.4 8947
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 485 low-speed end of drive Dimension F = 2.29.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

62 (131-110)

Rexnord 2014

Type AXV & AXVQ Triple Reduction


Sizes 505-555
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

Y
GA

AE
CLEARANCE

D
SHAFT
COVER

AD

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

AE
CLEARANCE

D
S

BA

UE

KA

BEARING
GREASE
FITTING

N
HA

HB

UA

AH
O

HC
R

HD
LA

BEARING
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

M
L

Dimensions (in)
Drive
Size

AD

AE

505

7.00

33.06

47.1

AH

47.62 17.32

BA

GA

6.80 44.000 19.62 27.87 31.00

535

8.00

35.18

50.8

52.00 19.50

6.80 51.000 22.62 30.00 35.75

555

9.00

40.39

58.5

59.30 21.80

6.60 57.000 24.62 34.95 40.00 10.00

Drive
Size

Low-Speed Shaft
N

Key

UA

UB

UC

UD

Lubrication System
H

9.91

HA

HB

HC

16.82 16.34 27.67

HD

2.80

KA

13.50 72.90 18.88 50.50 22.75

9.91

20.00 18.84 29.68

3.05

16.50 82.25 21.75 56.50 25.75

9.91

20.00 20.84 34.51

3.41

18.00 92.75 23.75 61.50 28.25

Keyed Hollow
Low-Speed Shaft
U
UE
+.002 +.000
Keyway
- .000 - .005

Wt (lb)

High-Speed Shaft
T

Key

AXV

AXVQ

505 39.25 37.46 10.90 10.50 2.25 9.250 2.500 x 1.750 x 14.00 16.18 1.500 3.00 6.00 9.001 24.999 2.000 x 0.510 3.500 0.875 x 0.875 x 6.00 2.250 74.53 12,950 13,000
535 45.25 40.45 10.98 10.50 2.25 10.500 2.500 x 1.750 x 16.00 18.38 1.500 3.00 7.50 10.501 27.999 2.500 x 0.760 4.000 1.000 x 1.000 x 7.00 2.250 84.60 18,200 18,050
555 49.25 46.54 13.00 12.00 2.31 11.500 3.000 x 2.000 x 17.00 20.12 1.750 3.50 8.00 11.501 28.999 3.000 x 0.760 4.500 1.000 x 1.000 x 8.00 2.250 94.62 24,350 23,950
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

Rexnord 2014

(131-110) 63

Type AXV & AXVQ Quadruple Reduction


Sizes 405-485
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
Y

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

LA

LA

AE
CLEARANCE

D
SHAFT
COVER

AD

6-HOLES FOR
X DIA. BOLT

J
F

BEARING
GREASE
FITTING

AE
CLEARANCE

D
S

2.8

BA

UE

2.8

HA

HB
HA

UA

HB

AH
O
E

HC

HC

HD
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

HD

Q
M

SIZE 405

L
SIZES 425-485

Dimensions (in)
Drive
Size

405

3.00

9.70 23.700 11.31 17.65

1.50

18.50

Lubrication System
H

7.47

HA

HB

HC

12.71 10.88 19.99

HD

1.25

9.20

40.00 27.75 12.50 21.62 22.70

6.11

5.00

1.50

425

3.00

11.00 26.700 12.31 19.45

1.50

21.00

7.65

13.19 10.03 19.57

1.35

10.25 45.00 31.80 14.50 24.62 24.50

7.00

6.00

1.60

445

3.50

12.20 30.500 14.62 21.41

1.75

24.00

9.92

16.88 12.09 21.42

1.18

12.25 51.50 37.00 16.75 29.25 27.10

7.55

7.00

1.81

465

3.50

14.00 34.700 16.62 23.16 1.95 27.20

9.92

18.88 13.34 23.20

1.42

14.10 58.25 41.00 18.75 33.25 28.90

8.11

7.00

1.79

485

4.50

15.90 39.300 18.50 25.00 2.41 30.60

9.92

18.88 15.09 24.97

1.87

15.60 65.90 46.50 21.00 37.00 31.90

9.24

8.00

2.00

Drive
Size

Low-Speed Shaft
S

Key

UA

UB

UC

Hollow Low-Speed Shaft


U
UE
UD +.002 +.000
Keyway
- .000 - .005

High-Speed Shaft
T

Key

AD

AE

AH

BA

LA

Wt
(lb)

405 5.000 1.250 x 1.250 x 7.500 8.66 0.750 1.88 3.50 5.375 15.249 1.000 x 0.312 1.500 0.375 x 0.375 x 2.750 42.45 1.125 41.12 4.500 21.34 30.6 29.10 4.50 5.7 2475
425 5.750 1.500 x 1.500 x 8.000 10.06 1.125 2.25 3.50 6.000 15.749 1.500 x 0.265 1.500 0.375 x 0.375 x 2.500 47.22 1.250 46.01 5.500 23.50 33.5 32.20 4.00 6.6 3256
445 6.500 1.500 x 1.500 x 10.000 11.38 1.250 2.50 4.00 6.750 18.499 1.500 x 0.510 1.750 0.375 x 0.375 x 3.000 53.75 1.500 52.67 6.000 25.50 36.4 35.60 4.60 6.7 4616
465 7.250 1.750 x 1.500 x 11.000 12.68 1.250 2.50 4.75 7.500 20.999 1.500 x 0.510 1.750 0.375 x 0.375 x 3.000 61.11 1.500 59.43 6.500 27.23 39.2 39.20 4.60 7.7 6879
485 8.000 2.000 x 1.500 x 12.000 14.00 1.500 3.00 5.00 8.500 23.749 1.500 x 0.510 2.250 0.500 x 0.500 x 4.000 68.02 2.000 67.04 7.200 29.18 41.9 43.10 5.40 9.4 9087
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465 low-speed end of drive Dimension F = 1.90.
Size 485 low-speed end of drive Dimension F = 2.29.
Size 425 low-speed end of drive Dimension LA = 6.7.
Size 485 low-speed end of drive Dimension LA = 9.5.

64 (131-110)

Rexnord 2014

Type AXV & AXVQ Quadruple Reduction


Sizes 505-555
Type AXVQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

Y
GA

AE
CLEARANCE

D
SHAFT
COVER

Z
AD

GA

FA

AE
CLEARANCE

D
S

BA

UE

KA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

FB

BEARING
GREASE
FITTING

N
HA

HB

UA

AH
O

HC
R

HD

BEARING
GREASE
FITTING
(AXVD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

Q
M

Dimensions (in)
Drive
Size

AD

AE

AH

BA

FA

FB

GA

Lubrication System
H

HA

HB

HC

HD

KA

505

5.38 33.06 47.1 47.62 17.32 6.80 44.000 19.62 27.87 3.40

3.50 31.00

9.91 16.82 16.34 27.67 2.80 13.50 72.90 18.88 50.50 22.75

535

6.00 35.18 50.8 52.00 19.50 6.80 51.000 22.62 30.00 3.73

3.50 35.75

9.91 20.00 18.84 29.68 3.05 16.50 82.25 21.75 56.50 25.75

555

6.00 40.39 58.5 59.30 21.80 6.60 57.000 24.62 34.95 4.50

3.50 40.00 10.00 9.91 20.00 20.84 34.51 3.41 18.00 92.75 23.75 61.50 28.25

Drive
Size

Low-Speed Shaft
N

Key

UA

UB

UC

Keyed Hollow
Low-Speed Shaft
U
UE
UD +.002 +.000
Keyway
- .000 - .005

Wt (lb)

High-Speed Shaft
T

Key

AXV

AXVQ

505 39.25 35.66 10.90 10.50 2.25 9.250 2.500 x 1.750 x 14.00 16.18 1.500 3.00 6.00 9.001 24.999 2.000 x 0.510 2.750 0.625 x 0.625 x 4.50 2.250 74.53 8.20 13,050 13,100
535 45.25 38.35 10.98 10.50 2.25 10.500 2.500 x 1.750 x 16.00 18.38 1.500 3.00 7.50 10.501 27.999 2.500 x 0.760 3.000 0.750 x 0.750 x 5.00 2.250 84.60 8.20 18,350 18,200
555 49.25 43.33 13.00 12.00 2.31 11.500 3.000 x 2.000 x 17.00 20.12 1.750 3.50 8.00 11.501 28.999 3.000 x 0.760 3.000 0.750 x 0.750 x 5.00 2.250 94.62 9.30 24,700 24,250
Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

Rexnord 2014

(131-110) 65

Type AB Drive Selection


Shaft Assemblies & Rotations
Type AB
Please specify from the views below, the desired assembly number. The Type AB low-speed shaft overhung load capacities published on page83 apply to the low-speed shaft
extensions below with heavy arrows. Published overhung load capacities may be increased when an outboard bearing is used. Consult Rexnord for overhung load capacities of low-speed
shaft extensions without the heavy arrow, as they are less than the heavy arrow extensions. Contact Rexnord for inclined, wall-mounted or other non-standard orientations.
Standard Assemblies
Other Available Assemblies

LOW-SPEED SHAFT

HIGH-SPEED SHAFT

LOWSPEED
SHAFT
GUARD

END
COVER

OUTBOARD
BEARING

Refer to Rexnord for overhung load ratings for low-speed shafts without the heavy arrows and without outboard bearings. They are less than those published.
Shaft Rotations for AB, ABR, ABRJ Assemblies
AB DOUBLE REDUCTION

AB, ABR, ABRJ TRIPLE REDUCTION

AB, ABR, ABRJ QUADRUPLE REDUCTION

42 41
44 43
46 45
48 47
50 49
52 51 Std.
Std. 54 53
ALL SIZES

1 2
3 4
5 6
42 41
44 43
46 45
48 47
50 49
52 51 Std.
Std. 54 53
ALL SIZES

1 2
3 4
5 6
42 41
44 43
46 45
48 47
50 49
52 51 Std.
Std. 54 53
ALL SIZES

Types ABR & ABRJ


Please specify from the views below, the desired assembly number. The Type ABR and ABRJ low-speed shaft overhung load capacities published on page83 apply to the low-speed
shaft extensions below with heavy arrows. Contact Rexnord for inclined or other non-standard orientations. For rotations of ABR and ABRJ assemblies, see shaft rotation schematic above.

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

LOW-SPEED
SHAFT

HIGH-SPEED
SHAFT

SHRINK DISC

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

HIGH-SPEED
SHAFT

SHRINK DISC

66 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Double Reduction


Type AB Right-Angle Shaft
Approx.
HighLowSpeed Nominal
Ratios Speed
Shaft
4%
Shaft
RPM
RPM

385

405

425

445

465

485

505

525

385

405

425

445

465

485

505

525

5.06

350

727

995

1369

2055

2450

127

178

243

391

432

5.60

310

709

995

1369

1938

2450

138

197

266

398

479

6.20

280

671

995

1369

1834

2384

147

222

306

409

537

6.86

255

636

995

1369

1674

2450

151

241

333

406

579

7.59

230

600

850

1259

1595

2279

2608

155

225

335

449

583

712

8.40

210

435

602

814

1333

1834

2608

127

173

239

408

548

766

9.30

190

435

602

814

1268

1647

2608

143

195

275

421

568

883

10.29

170

435

572

809

1166

1716

2608

155

219

298

421

620

961

11.39

155

419

340

762

1125

1579

2518

162

134

307

471

618

1014

12.61

140

251

340

481

792

1187

1583

111

148

212

360

535

698

13.95

125

251

340

481

792

1163

1583

125

167

245

390

605

804

15.44

115

251

340

481

792

1187

1562

136

181

266

425

648

863

17.09

100

251

340

481

774

1118

1583

148

198

291

481

660

957

5.06

280

611

839

1162

1784

2107

131

183

253

415

455

5.60

255

611

839

1162

1683

2107

146

203

276

423

504

6.20

230

582

839

1162

1592

2070

156

229

318

434

571

6.86

210

552

839

1162

1453

2107

160

248

346

431

610

7.59

190

509

705

1046

1350

1979

2219

2766

3516

161

228

341

465

619

741

931

1148

8.40

170

362

502

681

1158

1593

2219

2766

3516

129

176

244

434

582

798

1001

1271

1750

1430

1170

Horsepower

Torque

Drive Size

Drive Size

9.30

155

362

502

681

1101

1429

2219

2766

3516

146

199

282

447

603

919

1163

1435

10.29

140

362

495

681

1012

1490

2219

2766

3516

158

232

307

448

659

1000

1274

1554

11.39

125

345

282

661

930

1371

2186

2766

3479

163

136

325

477

656

1078

1396

1682

12.61

115

207

282

399

659

992

1327

1741

2277

112

150

215

366

548

716

937

1241

13.95

100

207

282

399

659

992

1327

1741

2277

127

170

248

397

632

824

1089

1401

15.44

90

207

282

399

659

992

1327

1741

2277

137

184

270

432

663

897

1192

1517

17.09

84

207

282

399

638

971

1327

1741

2277

149

201

296

485

702

981

1307

1660

5.06

230

512

704

980

1551

1794

134

188

260

441

474

5.60

210

512

704

980

1462

1794

149

208

285

449

524

6.20

190

494

704

980

1384

1794

162

235

328

461

605

6.86

170

479

703

980

1263

1794

170

254

357

458

634

7.59

155

420

583

867

1121

1720

1874

2344

2992

162

231

345

472

658

765

964

1194

8.40

140

301

418

568

972

1384

1874

2344

2992

132

179

249

445

618

824

1037

1322

9.30

125

301

418

568

957

1242

1874

2344

2992

148

202

287

475

640

949

1205

1492

10.29

115

301

408

568

880

1294

1874

2344

2992

160

234

313

476

700

1032

1319

1616

11.39

100

285

233

568

769

1191

1814

2344

2992

165

137

342

482

697

1093

1446

1768

12.61

90

171

233

331

548

826

1108

1456

1909

114

152

218

372

557

730

958

1272

13.95

84

171

233

331

548

826

1108

1456

1909

128

171

252

404

643

841

1113

1435

15.44

75

171

233

331

548

826

1108

1456

1909

138

186

274

440

674

916

1219

1555

17.09

68

171

233

331

525

826

1108

1456

1870

150

203

300

488

729

1001

1336

1666

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.

Rexnord 2014

(131-110) 67

Horsepower & Torque Ratings/Double Reduction


Type AB Right-Angle Shaft
Approx.
HighLowSpeed Nominal
Ratios Speed
Shaft
4%
Shaft
RPM
RPM

385

405

425

445

465

485

505

525

385

405

425

445

465

485

505

525

5.06

175

390

538

754

1212

1394

137

193

269

464

495

5.60

155

383

538

754

1188

1394

150

214

294

491

548

6.20

140

367

538

754

1125

1394

162

242

339

504

632

6.86

130

356

530

750

1026

1394

170

258

367

501

663

7.59

115

316

439

654

847

1394

1444

1813

2324

164

234

350

479

717

793

1003

1247

8.40

105

227

316

432

742

1100

1444

1813

2324

133

182

255

457

661

854

1078

1381

9.30

95

227

316

432

742

1010

1444

1813

2324

150

206

294

495

700

983

1253

1559

10.29

85

227

306

432

715

1041

1444

1813

2324

163

236

320

520

757

1070

1372

1688

11.39

77

213

175

432

578

943

1349

1813

2236

166

139

350

487

742

1093

1504

1777

12.61

70

129

175

249

414

627

843

1111

1459

115

153

221

378

569

747

983

1307

13.95

62

129

175

249

414

627

843

1111

1459

130

173

255

410

656

861

1142

1475

15.44

55

129

175

249

414

627

843

1111

1459

140

188

277

447

688

937

1250

1598

17.09

50

129

175

249

393

627

843

1111

1391

153

205

303

491

745

1025

1371

1666

5.06

140

327

451

634

1023

1178

139

196

274

473

505

5.60

130

317

451

634

1023

1159

150

217

299

511

550

6.20

115

304

451

634

985

1178

162

245

345

533

645

6.86

105

295

442

621

899

1178

170

260

368

530

677

7.59

95

263

366

545

707

1178

1216

1529

1964

165

235

353

483

732

807

1022

1273

8.40

85

190

264

361

622

924

1216

1529

1964

135

184

257

463

671

868

1099

1411

870

720

580

Horsepower

Torque

Drive Size

Drive Size

9.30

77

190

264

361

622

884

1216

1529

1964

152

208

297

502

741

1000

1277

1592

10.29

70

190

255

361

622

868

1216

1529

1964

164

238

323

546

763

1089

1398

1724

11.39

62

177

146

361

481

786

1116

1529

1850

167

140

353

490

747

1093

1532

1776

12.61

55

107

146

208

346

524

705

931

1224

115

155

223

382

574

755

995

1325

13.95

50

107

146

208

346

524

705

931

1224

130

175

257

414

663

870

1156

1496

15.44

45

107

146

208

346

524

705

931

1224

141

189

280

451

695

947

1266

1620

17.09

42

107

146

208

327

524

705

931

1151

153

207

306

494

752

1035

1388

1666

5.06

115

265

368

519

839

959

140

198

278

481

511

5.60

105

255

368

519

839

933

150

220

304

520

550

6.20

95

245

368

518

839

968

162

248

350

564

658

6.86

85

237

358

500

773

968

170

261

367

566

691

7.59

77

213

296

442

574

961

995

1253

1613

166

236

355

487

742

820

1039

1298

8.40

70

154

215

294

507

755

995

1253

1613

136

186

260

468

681

882

1118

1438

9.30

62

154

215

294

507

755

995

1253

1613

153

210

300

508

785

1016

1299

1623

10.29

55

154

206

294

507

704

995

1253

1607

165

238

326

553

768

1106

1422

1751

11.39

50

143

118

294

389

637

899

1253

1491

167

140

357

492

752

1093

1559

1777

12.61

45

86.7

118

168

281

426

574

758

998

116

155

224

385

580

763

1006

1341

13.95

42

86.7

118

168

281

426

574

758

998

131

175

258

418

669

879

1169

1514

15.44

38

86.7

118

168

281

426

574

758

996

141

190

281

455

702

957

1280

1636

17.09

34

86.7

118

168

264

425

574

758

927

154

207

307

495

757

1047

1403

1666

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.

68 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Triple Reduction


Horsepower Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

1750

1430

1170

Nominal
Ratios
4%

Approx.
LowSpeed
Shaft
RPM

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16

125
115
100
90
84
75
68
60
56
50
45
40
37
34
30
27
25
22
100
90
84
75
68
60
56
50
45
40
37
34
30
27
25
22
20
18
84
75
68
60
56
50
45
40
37
34
30
27
25
22
20
18
16.5
15.0

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

230
218
209
189
145
141
141
126
96.5
95.5
95.5
76.4
64.8
64.7
64.7

190
178
171
154
118
116
116
103
78.9
78.5
78.5
62.9
52.9
53.1
53.1

155
146
140
126
96.8
95.7
95.7
84.2
64.5
64.5
64.5
51.8
43.3
43.6
43.6

314
314
314
294
314
294
286
254
213
175
175
171
145
127
98.2
98.2
97.6

262
262
262
243
261
244
236
208
176
145
145
145
119
104
80.6
80.6
79.9

217
217
217
199
214
199
194
171
145
120
120
119
97.3
84.9
66.2
66.2
65.4

536
536
536
467
467
462
418
390
326
290
284
259
240
186
177
167
158

466
466
466
406
406
377
348
318
270
251
232
212
196
153
153
140
129

400
400
400
353
333
309
285
261
222
206
190
173
161
126
125
114
106

727
727
727
727
675
651
614
526
436
435
435
371
293
271
251
250
194

611
611
611
611
586
565
532
453
358
362
358
304
240
222
207
207
159

512
512
509
509
503
470
437
372
294
301
293
249
197
182
171
171
130

995
995
970
970
920
859
777
773
647
602
599
478
434
340
340
329
298

839
839
839
839
798
746
675
635
531
497
502
408
369
282
282
270
244

704
704
704
704
694
648
586
522
436
408
415
335
302
233
233
221
200

1369
1369
1369
1369
1369
1369
1223
1207
1112
943
814
808
743
630
481
481
481

1162
1162
1162
1162
1162
1162
1062
992
913
775
681
663
610
517
399
399
399

980
980
962
962
962
962
884
816
751
637
568
544
500
424
331
331
331

2154
2154
2154
2154
2044
2154
1921
1769
1379
1379
1305
1201
999
792
792
792
675

1845
1845
1845
1845
1775
1784
1580
1455
1160
1160
1072
986
819
659
659
659
552

1566
1566
1566
1566
1486
1486
1300
1196
972
972
880
809
670
548
548
548
451

2450
2450
2450
2316
2087
1755
1755
1537
1383
1187
1187
1027
980
816

2107
2107
2107
1907
1718
1524
1524
1262
1136
992
992
842
803
669

1794
1792
1755
1570
1414
1324
1298
1037
933
826
826
691
659
548

2450
2450
2450
2450
2450
2450
2450
2301
2087
1935
1755
1526
1383
1187
1187
1020
924

2107
2107
2107
2107
2107
2107
2107
1894
1717
1591
1524
1253
1136
992
992
836
757

1794
1794
1794
1794
1794
1755
1755
1560
1413
1309
1288
1030
933
826
826
686
621

3436
3436
3436
3436
3212
3212
3212
2608
2246
2246
2202
2036
1583
1583
1468
1357
1061

2985
2985
2985
2985
2789
2789
2750
2219
1950
1950
1799
1663
1327
1308
1200
1109
870

2560
2560
2560
2560
2423
2423
2250
1874
1689
1605
1472
1361
1108
1070
981
907
713

3436
3436
3436
3436
3436
3426
3205
2977
2608
2546
2151
1982
1583
1583
1455
1341

2985
2985
2985
2985
2985
2974
2661
2454
2177
2130
1771
1632
1327
1327
1197
1102

2560
2560
2560
2560
2560
2560
2196
2024
1795
1756
1459
1344
1108
1108
985
907

3790
3790
3790
3790
3790
3672
3326
3090
2766
2485
2283
2092
1741
1671
1547
1415
1109

3266
3266
3266
3266
3266
3191
2781
2549
2317
2033
1881
1722
1456
1367
1265
1158
913

4673
4673
4673
4673
4673
4156
4156
3384
3212
3212
3025
2913
2277
2255
2180
1961
1815

4058
4058
4058
4058
4058
3611
3611
2940
2791
2791
2628
2402
1909
1909
1784
1615
1494

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Triple reduction ratios and ratings are offered for Types ABR and ABX only.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
HighSpeed
Shaft
RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

Rexnord 2014

(131-110) 69

Horsepower & Torque Ratings/Triple Reduction


Torque Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
4%

Approx.
LowSpeed
Shaft
RPM

385

405

425

445

465

485

505

525

535

545

555

565

585

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16

125
115
100
90
84
75
68
60
56
50
45
40
37
34
30
27
25
22
100
90
84
75
68
60
56
50
45
40
37
34
30
27
25
22
20
18
84
75
68
60
56
50
45
40
37
34
30
27
25
22
20
18
16.5
15.0

156
166
172
168
152
157
170
168
152
159
172
165
152
161
174

157
166
173
168
151
158
171
168
152
160
173
166
152
161
175

157
166
173
168
152
159
172
168
152
161
174
167
152
162
175

163
181
200
197
245
236
259
249
246
211
238
253
251
241
207
234
252

166
185
204
199
249
240
262
250
249
214
241
263
252
241
208
235
252

168
187
207
199
249
239
263
251
250
216
244
263
252
241
209
236
252

264
289
333
310
358
385
379
388
375
363
387
387
390
354
367
379
390

281
307
354
330
381
385
386
387
380
385
387
388
390
356
388
389
390

295
323
372
351
382
385
387
388
382
386
387
387
392
359
387
387
392

377
407
441
476
522
535
547
553
491
536
582
585
495
495
510
553
497

388
419
453
490
555
568
580
583
493
546
586
587
496
497
515
560
499

397
429
461
499
582
578
583
585
495
555
586
587
497
498
520
566
499

495
548
574
635
695
703
734
766
751
749
821
744
731
613
708
778
762

511
565
607
672
738
747
780
770
754
756
842
777
760
622
718
781
764

524
580
623
689
784
793
828
773
757
759
850
780
760
629
725
782
765

698
751
824
887
1021
1111
1149
1235
1238
1148
1155
1248
1249
1159
1027
1118
1217

725
780
856
921
1061
1155
1221
1242
1244
1155
1183
1254
1255
1164
1043
1135
1236

747
804
866
932
1073
1168
1243
1249
1251
1160
1206
1257
1258
1166
1058
1151
1253

1133
1218
1404
1510
1561
1770
1834
1839
1569
1687
1856
1860
1694
1438
1671
1820
1698

1187
1277
1472
1583
1659
1794
1846
1851
1615
1737
1866
1869
1700
1464
1702
1853
1700

1232
1325
1527
1642
1698
1826
1857
1860
1654
1779
1872
1874
1699
1488
1730
1884
1697

1757
1903
1988
2121
2070
1966
2178
2152
2098
2008
2224
2171
2173
2120

1849
2002
2092
2137
2085
2089
2314
2163
2108
2053
2274
2178
2179
2127

1924
2081
2130
2150
2098
2219
2409
2172
2117
2089
2315
2185
2186
2129

1292
1425
1599
1758
1973
2036
2246
2366
2321
2383
2460
2400
2352
2207
2512
2422
2372

1360
1500
1682
1851
2076
2143
2364
2384
2337
2397
2614
2412
2364
2257
2569
2429
2378

1415
1561
1751
1926
2161
2182
2406
2400
2350
2411
2700
2423
2373
2297
2615
2436
2385

1664
1811
2046
2236
2370
2591
2899
2594
2533
2769
3038
3057
2678
2927
3038
3057
2674

1769
1926
2175
2377
2519
2753
3038
2701
2692
2942
3037
3056
2748
2960
3039
3057
2684

1854
2018
2280
2492
2675
2923
3038
2788
2850
2959
3038
3057
2804
2959
3037
3056
2688

1834
2029
2292
2499
2786
3088
3220
3256
3232
3508
3304
3313
2943
3272
3352
3362

1950
2157
2436
2657
2962
3281
3272
3284
3301
3591
3329
3339
3019
3356
3375
3382

2044
2261
2554
2785
3104
3452
3300
3311
3327
3619
3352
3360
3081
3425
3394
3402

2305
2548
2920
3171
3459
3604
3794
3859
3789
3901
3909
3922
3547
3902
3939
3945
3443

2427
2684
3076
3340
3643
3828
3877
3891
3879
3901
3936
3945
3625
3901
3937
3946
3464

2868
3120
3380
3684
4038
4095
4490
4094
4304
4719
5015
5310
4553
4994
5449
5389
5402

3043
3311
3587
3910
4286
4349
4768
4347
4571
5011
5325
5351
4665
5168
5450
5424
5435

1750

1430

1170

Drive Size

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Triple reduction ratios and ratings are offered for Types ABR and ABX only.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

70 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Triple Reduction


Horsepower Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
4%

Approx.
LowSpeed
Shaft
RPM

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16

62
55
50
45
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
50
45
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
8.3
7.5

870

720

580

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

115
109
104
93.9
72.0
71.8
71.8
62.6
48.0
48.2
48.2
38.8
32.2
32.5
32.5

95.5
89.9
86.0
77.7
59.6
59.6
59.6
51.8
39.7
40.0
40.0
32.2
26.6
26.9
26.9

76.9
72.4
69.3
62.6
48.0
48.2
48.2
41.7
32.0
32.3
32.3
26.0
21.5
21.7
21.7

165
161
161
148
160
148
145
127
108
90.2
90.2
88.9
72.5
63.3
49.4
49.4
48.7

137
133
133
122
133
123
120
105
89.8
75.1
75.1
73.6
60.0
52.4
41.0
41.0
40.3

112
107
107
98.6
107
98.9
96.7
85.1
72.5
60.8
60.8
59.4
48.4
42.3
33.1
33.1
32.5

305
305
300
268
247
230
212
194
165
153
141
129
120
94.9
92.9
84.9
78.7

255
255
248
221
205
190
175
160
136
126
117
107
98.9
78.9
76.9
70.2
65.1

207
207
200
178
165
153
141
129
110
102
94.1
86.0
79.7
63.9
61.9
56.6
52.5

390
390
379
379
376
349
327
278
219
227
219
186
147
136
129
129
96.9

327
327
313
313
312
289
271
230
182
190
181
154
122
112
107
107
80.2

266
266
252
252
252
233
219
186
147
154
146
124
98.1
90.6
86.7
86.7
64.7

538
538
538
538
538
494
447
390
326
304
310
250
226
175
175
165
149

451
451
451
451
451
412
371
324
270
252
257
207
187
146
146
137
123

368
368
368
368
368
334
300
261
218
204
207
167
151
118
118
110
99.5

753
753
716
716
716
716
658
610
561
476
432
406
373
316
249
249
249

623
623
592
592
592
592
544
506
465
394
361
337
309
262
208
208
206

502
502
477
477
477
477
438
409
376
318
294
272
250
212
168
168
166

1212
1212
1212
1212
1128
1105
973
895
742
742
657
604
498
414
414
409
336

1023
1023
1023
1023
943
915
808
743
622
614
545
501
412
346
346
339
278

839
839
839
839
764
737
653
600
507
495
440
404
332
281
281
273
224

1394
1344
1305
1176
1058
1071
970
774
697
627
627
515
491
409

1174
1117
1080
977
879
887
805
642
578
524
524
427
407
339

946
904
870
789
710
714
650
519
466
426
426
345
329
273

1394
1394
1394
1394
1394
1305
1305
1168
1058
979
963
769
696
627
627
512
463

1178
1178
1178
1175
1175
1080
1080
970
878
812
799
638
578
524
524
424
384

968
968
968
946
946
870
870
784
710
656
645
515
466
426
426
342
310

2005
2005
2005
2005
1920
1824
1673
1444
1256
1193
1095
1012
838
796
730
675
532

1701
1701
1701
1701
1589
1510
1385
1209
1040
988
906
838
693
658
604
558
441

1401
1401
1401
1401
1280
1216
1115
974
838
796
730
675
558
530
487
450
356

2005
2005
2005
2005
2005
1986
1651
1521
1348
1318
1095
1009
843
843
738
680

1701
1701
1701
1701
1692
1655
1375
1267
1123
1097
911
839
705
705
614
565

1401
1401
1401
1401
1373
1342
1115
1027
910
889
738
680
574
574
497
457

2571
2571
2571
2571
2571
2417
2092
1917
1723
1512
1399
1281
1111
1017
941
861
684

2186
2186
2186
2186
2140
2000
1738
1591
1426
1251
1158
1060
931
841
779
713
569

1805
1805
1805
1805
1724
1611
1400
1282
1149
1008
933
854
758
678
627
574
460

3218
3218
3218
3218
3218
2935
2935
2324
2268
2235
2000
1804
1459
1459
1327
1211
1120

2746
2746
2746
2746
2746
2571
2540
1964
1945
1849
1655
1501
1224
1224
1098
1006
929

2275
2275
2275
2275
2275
2153
2046
1613
1567
1490
1333
1217
998
988
884
811
749

For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Triple reduction ratios and ratings are offered for Types ABR and ABX only.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

Rexnord 2014

(131-110) 71

Horsepower & Torque Ratings/Triple Reduction


Torque Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
4%

Approx.
LowSpeed
Shaft
RPM

385

405

425

445

465

485

505

525

535

545

555

565

585

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16

62
55
50
45
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
50
45
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
42
38
34
31
28
25
22
21
18
17
15
14
12.5
11.0
10.0
9.1
8.3
7.5

157
167
172
168
152
161
174
168
152
162
175
168
152
162
176

157
166
172
168
152
161
174
168
152
162
176
169
151
162
176

157
166
172
168
152
162
175
168
152
163
176
169
152
163
176

172
186
207
199
251
239
264
251
251
219
247
265
253
241
210
237
253

172
186
206
199
252
240
264
251
252
220
248
265
253
241
210
237
253

175
186
206
199
252
240
265
252
253
221
250
265
253
242
211
238
253

303
331
375
358
381
386
387
388
382
386
387
388
392
363
387
387
391

306
334
375
357
382
385
386
387
380
384
388
388
391
365
387
387
391

308
337
375
357
381
385
386
387
382
386
387
388
391
367
387
387
391

407
440
462
499
585
577
586
588
496
563
589
590
499
500
527
574
500

412
445
461
498
586
577
587
588
498
569
588
590
501
498
528
575
500

416
450
461
498
588
578
589
590
499
573
589
590
500
500
531
579
501

538
596
640
709
818
813
849
777
761
760
854
783
765
635
733
785
766

545
604
648
718
828
820
852
780
762
762
856
783
765
640
739
787
765

552
611
657
727
839
825
855
780
763
765
856
784
767
642
741
785
768

772
831
867
933
1074
1169
1244
1255
1256
1166
1233
1262
1262
1169
1070
1164
1267

772
831
866
932
1073
1168
1243
1258
1258
1166
1246
1266
1263
1171
1080
1175
1267

772
831
866
932
1074
1168
1242
1262
1263
1168
1259
1268
1269
1177
1083
1179
1267

1282
1379
1589
1709
1733
1826
1869
1872
1698
1826
1879
1882
1699
1512
1757
1891
1701

1308
1406
1621
1743
1751
1827
1875
1878
1720
1826
1884
1886
1698
1527
1775
1894
1700

1331
1432
1650
1775
1761
1827
1881
1882
1740
1828
1888
1888
1699
1540
1789
1893
1701

2010
2099
2130
2166
2111
2413
2421
2180
2126
2133
2363
2190
2190
2137

2046
2108
2130
2175
2119
2415
2428
2185
2131
2154
2386
2194
2193
2140

2047
2118
2130
2180
2125
2413
2434
2193
2132
2174
2408
2201
2201
2140

1479
1631
1830
2013
2258
2182
2406
2416
2367
2425
2715
2433
2381
2344
2669
2445
2391

1510
1665
1868
2050
2300
2182
2406
2425
2373
2430
2722
2439
2389
2368
2695
2447
2396

1540
1699
1906
2049
2298
2182
2406
2433
2382
2437
2728
2444
2391
2389
2720
2450
2401

1953
2126
2402
2625
2850
2959
3038
2889
2850
2958
3039
3057
2852
2961
3039
3058
2697

2002
2179
2462
2691
2850
2960
3039
2923
2851
2960
3038
3059
2850
2957
3038
3055
2702

2047
2228
2517
2751
2850
2959
3037
2923
2852
2961
3039
3058
2849
2957
3041
3058
2708

2153
2381
2690
2933
3270
3601
3337
3346
3360
3653
3383
3393
3152
3504
3420
3430

2207
2441
2757
3007
3334
3626
3358
3368
3382
3674
3401
3409
3185
3541
3438
3443

2256
2496
2819
3075
3359
3650
3380
3389
3402
3696
3420
3430
3219
3579
3455
3457

2570
2842
3256
3536
3856
3899
3922
3935
3879
3902
3937
3947
3720
3903
3939
3946
3490

2640
2919
3345
3633
3879
3899
3938
3946
3879
3901
3938
3947
3767
3900
3940
3948
3508

2706
2992
3429
3724
3879
3898
3937
3948
3880
3902
3939
3947
3807
3903
3936
3946
3521

3246
3531
3826
4170
4571
4754
5211
4621
4996
5397
5450
5405
4795
5311
5452
5470
5479

3347
3641
3945
4300
4713
5032
5450
4719
5177
5395
5449
5434
4861
5384
5451
5491
5492

3442
3745
4057
4422
4847
5231
5449
4811
5177
5397
5448
5469
4920
5395
5447
5495
5496

870

720

580

Drive Size

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Triple reduction ratios and ratings are offered for Types ABR and ABX only.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

72 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Quadruple Reduction


Horsepower Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
5%

Approx.
LowSpeed
Shaft
RPM

78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5

22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2

1750

1430

1170

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

53.0
50.8
42.6
40.7
36.8
35.2
28.5
28.5
24.7
23.6
19.2
19.1
16.4
13.1

43.3
41.5
34.8
33.3
30.1
28.8
23.3
23.3
20.2
19.3
15.7
15.6
13.4
10.7

35.4
33.9
28.5
27.2
24.6
23.5
19.1
19.1
16.5
15.8
12.9
12.8
10.9
8.76

82.4
79.8
73.6
64.8
56.6
58.5
49.5
43.6
38.0
39.3
31.8
27.8
28.1
22.5
20.9
19.2
70.8
65.2
60.2
53.0
46.3
47.8
40.5
35.6
31.1
32.1
26.0
22.7
22.9
18.4
17.1
15.7
57.9
53.4
49.3
43.4
37.9
39.2
33.1
29.2
25.4
26.3
21.3
18.6
18.8
15.1
14.0
12.9

143
122
112
104
95.4
81.7
75.8
69.9
63.9
54.8
50.8
46.9
42.9
37.9
34.8
31.8
117
100
91.8
84.7
77.9
66.8
61.9
57.1
52.2
44.8
41.5
38.3
35.0
31.0
28.5
26.0
95.7
81.9
75.1
69.3
63.8
54.6
50.7
46.7
42.7
36.6
34.0
31.4
28.7
25.4
23.3
21.3

218
198
168
153
146
133
122
105
98.7
89.1
75.6
70.8
65.0
55.3
51.1
40.3
179
162
137
125
120
108
99.6
86.2
80.8
72.9
61.8
57.9
53.2
45.2
41.8
33.0
147
133
112
102
98.3
88.8
81.6
70.5
66.2
59.7
50.6
47.4
43.5
37.0
34.2
27.0

305
268
232
227
205
182
162
150
135
120
105
101
79.9
72.0
65.1
60.1
250
223
201
186
168
149
140
123
111
98.2
85.6
82.9
65.3
58.9
53.2
49.1
205
183
174
152
138
122
115
100
90.9
80.4
70.1
67.9
53.5
48.2
43.6
40.2

416
408
377
326
301
273
252
218
201
180
166
144
132
122
113
103
362
334
308
267
246
224
206
178
164
147
136
118
108
99.9
92.0
84.6
314
274
253
219
201
183
169
146
135
121
111
96.2
88.7
81.8
75.3
69.2

660
605
556
485
446
418
384
335
308
276
254
221
203
187
172
143
540
495
455
397
365
342
314
274
252
226
207
181
166
153
140
117
443
406
373
325
299
280
258
225
206
185
170
148
136
125
115
95.8

846
694
692
552
527
480
478
382
337
317
279
252
240
200
181
168
692
568
566
452
431
393
391
312
275
259
229
206
196
163
148
137
566
466
464
370
353
322
321
256
225
212
187
169
161
134
121
112

858
858
759
687
655
597
523
475
419
340
340
313
299
238
210
185
701
701
620
562
536
489
427
389
343
282
282
256
244
195
172
152
574
574
507
461
439
400
350
318
281
233
233
210
200
160
141
124

1147
1045
895
821
759
685
601
551
510
462
403
371
343
294
272
209
938
856
731
671
620
560
491
450
416
377
329
303
281
240
222
171
767
702
598
549
508
458
402
368
341
309
269
248
230
197
182
140

1289
1192
1047
968
804
740
710
656
545
501
483
446
370
341
294
271
1060
980
860
795
660
608
583
539
447
411
396
366
303
279
241
222
872
806
707
654
543
499
479
442
367
338
325
300
249
229
198
182

1379
1244
1152
1031
930
814
756
675
624
554
500
447
414
382
309
283
1127
1017
942
843
760
665
617
551
510
453
409
365
338
312
254
232
922
832
770
690
622
544
505
451
417
370
335
299
276
256
208
190

1848
1690
1532
1367
1235
1132
1023
936
845
773
677
620
560
513
473
433
1529
1381
1259
1117
1009
925
836
765
690
632
553
506
457
419
387
354
1251
1130
1036
914
826
757
684
626
565
517
453
414
374
343
317
289

For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

Rexnord 2014

(131-110) 73

Horsepower & Torque Ratings/Quadruple Reduction


Torque Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
5%

Approx.
LowSpeed
Shaft
RPM

78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5

22.0
20.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
18.0
16.5
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
15.0
13.5
12.0
11.0
10.0
9.0
8.1
7.5
6.6
6.0
5.4
5.0
4.4
4.0
3.6
3.2

1750

1430

1170

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

163
169
166
172
168
174
163
176
168
174
163
176
177
153

163
169
166
172
168
174
163
176
168
174
163
176
177
153

163
169
167
172
168
174
163
176
168
174
164
176
175
153

241
252
265
253
241
265
265
253
241
266
253
242
254
242
242
241
253
252
265
253
242
265
266
253
242
265
253
242
253
242
242
242
253
253
265
253
242
266
265
254
241
266
254
242
254
243
242
243

381
380
384
388
381
387
391
387
387
381
385
387
388
384
390
391
382
381
385
387
381
387
390
387
387
382
385
386
387
384
391
391
381
381
385
387
381
387
391
386
387
381
385
387
388
385
391
391

597
588
550
592
600
593
592
590
605
592
592
593
592
593
593
501
600
589
549
591
604
589
592
592
606
593
592
593
593
593
594
502
602
591
548
590
604
592
592
592
607
593
593
593
593
593
594
502

829
840
758
855
837
857
804
859
837
859
788
856
768
786
769
769
831
855
803
858
839
859
850
862
842
860
786
860
768
787
769
768
833
858
850
857
843
859
853
856
843
860
787
861
769
787
770
769

1113
1257
1264
1261
1267
1261
1267
1264
1269
1263
1268
1269
1266
1266
1276
1266
1185
1259
1264
1264
1267
1267
1268
1264
1267
1263
1271
1272
1268
1268
1271
1273
1256
1262
1269
1267
1265
1265
1271
1267
1275
1270
1268
1268
1272
1269
1272
1272

1881
1883
1884
1887
1890
1887
1888
1891
1893
1893
1897
1895
1895
1899
1902
1833
1884
1885
1887
1890
1892
1890
1889
1893
1895
1897
1892
1899
1897
1902
1895
1836
1889
1890
1891
1891
1895
1891
1897
1899
1894
1898
1899
1898
1899
1899
1902
1837

2360
2185
2432
2190
2192
2192
2437
2198
2200
2199
2196
2203
2200
2148
2140
2148
2362
2188
2435
2194
2194
2196
2440
2197
2197
2199
2206
2204
2199
2143
2141
2144
2362
2194
2439
2195
2197
2200
2448
2203
2197
2200
2201
2210
2208
2153
2139
2142

2452
2704
2733
2728
2728
2729
2732
2736
2738
2361
2679
2739
2744
2451
2454
2453
2451
2703
2732
2731
2732
2736
2729
2742
2743
2397
2719
2741
2740
2457
2460
2466
2453
2705
2730
2738
2735
2735
2734
2740
2747
2420
2746
2748
2745
2464
2465
2459

3131
3192
3051
3132
3151
3117
3051
3131
3154
3119
3133
3128
3148
3129
3151
2710
3133
3200
3049
3132
3150
3118
3051
3129
3149
3115
3131
3127
3156
3126
3147
2713
3131
3207
3049
3132
3155
3117
3053
3128
3154
3121
3128
3128
3157
3136
3154
2715

3654
3664
3678
3688
3414
3420
3715
3722
3447
3449
3750
3756
3473
3484
3484
3495
3677
3686
3697
3706
3430
3439
3733
3743
3460
3463
3763
3772
3481
3488
3495
3504
3697
3706
3715
3727
3449
3450
3749
3751
3472
3481
3775
3778
3496
3499
3509
3511

3894
3860
3899
3900
3878
3863
3941
3905
3936
3939
3935
3904
3943
3935
3544
3554
3895
3862
3901
3903
3879
3862
3936
3901
3937
3941
3939
3901
3939
3933
3566
3566
3894
3862
3898
3904
3880
3861
3937
3902
3935
3934
3943
3906
3932
3945
3569
3569

5383
5449
5431
5396
5396
5461
5463
5495
5461
5493
5458
5495
5464
5496
5488
5495
5450
5449
5462
5395
5395
5461
5463
5497
5457
5496
5456
5489
5456
5493
5495
5498
5450
5449
5493
5396
5398
5462
5463
5497
5461
5495
5462
5489
5458
5496
5502
5486

For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

74 (131-110)

Rexnord 2014

Horsepower & Torque Ratings/Quadruple Reduction


Horsepower Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
5%

Approx.
LowSpeed
Shaft
RPM

78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.5
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5

11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6

870

720

580

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

26.3
25.2
21.2
20.3
18.3
17.5
14.2
14.2
12.3
11.7
9.57
9.51
8.14
6.51

21.8
20.9
17.5
16.8
15.1
14.5
11.8
11.7
10.2
9.72
7.92
7.87
6.73
5.39

17.6
16.8
14.1
13.5
12.2
11.7
9.50
9.45
8.19
7.83
6.38
6.34
5.43
4.34

43.1
39.8
36.7
32.3
28.2
29.1
24.6
21.7
18.9
19.6
15.8
13.8
14.0
11.2
10.4
9.57
35.6
32.9
30.4
26.7
23.3
24.1
20.4
18.0
15.7
16.2
13.1
11.4
11.6
9.27
8.62
7.92
28.7
26.5
24.5
21.6
18.8
19.4
16.4
14.5
12.6
13.0
10.6
9.21
9.31
7.47
6.94
6.38

71.1
60.9
55.8
51.5
47.4
40.6
37.7
34.8
31.8
27.2
25.3
23.3
21.3
18.9
17.3
15.8
58.9
50.4
46.2
42.7
39.2
33.6
31.2
28.8
26.3
22.5
20.9
19.3
17.6
15.6
14.3
13.1
47.4
40.6
37.2
34.4
31.6
27.1
25.1
23.2
21.2
18.2
16.8
15.5
14.2
12.6
11.5
10.5

110
99.0
83.4
76.2
73.3
66.1
60.7
52.5
49.3
44.4
37.7
35.2
32.4
27.5
25.4
20.1
90.8
82.0
69.0
63.1
60.7
54.7
50.3
43.5
40.8
36.7
31.2
29.2
26.8
22.8
21.1
16.6
73.3
66.1
55.6
50.8
49.0
44.1
40.5
35.0
32.9
29.6
25.1
23.5
21.6
18.4
17.0
13.4

153
136
130
113
103
90.8
85.5
74.7
67.7
59.8
52.1
50.5
39.8
35.9
32.4
29.9
127
113
107
93.9
85.0
75.2
70.8
61.9
56.1
49.5
43.2
41.8
32.9
29.7
26.8
24.8
103
90.9
86.6
75.7
68.6
60.6
57.1
49.9
45.2
39.9
34.8
33.7
26.5
23.9
21.6
20.0

236
204
188
163
150
136
126
109
100
89.9
82.8
71.6
66.0
60.8
56.0
51.5
196
169
156
135
124
113
104
90.0
82.9
74.4
68.5
59.3
54.6
50.4
46.4
42.6
158
136
126
109
100
91.0
83.8
72.5
66.8
59.9
55.2
47.8
44.0
40.6
37.4
34.3

330
302
278
242
222
209
192
167
154
138
126
110
101
93.0
85.4
71.4
273
250
230
201
184
173
159
138
127
114
105
91.2
83.7
77.0
70.7
59.1
220
202
185
162
148
139
128
112
102
91.8
84.3
73.5
67.5
62.0
57.0
47.7

421
347
346
276
263
240
239
190
168
158
139
125
120
99.4
90.3
83.5
348
287
286
228
218
198
198
158
139
131
115
104
99.0
82.3
74.8
69.1
281
232
231
184
176
160
159
127
112
105
92.9
83.7
79.8
66.3
60.3
55.7

427
427
377
343
327
298
260
237
209
175
173
156
149
119
105
92.3
353
353
312
284
271
247
215
196
173
146
144
129
123
98.3
86.7
76.4
284
284
251
229
219
199
173
158
139
118
116
104
99.3
79.3
69.8
61.6

570
523
445
408
377
341
299
274
253
230
200
185
171
146
135
104
472
433
368
338
312
282
247
227
210
190
166
153
141
121
112
86.2
380
348
297
272
252
227
199
183
169
153
133
123
114
97.5
90.2
69.4

653
603
529
489
406
374
358
331
274
252
243
224
186
171
148
136
543
501
440
406
337
310
297
275
228
210
201
186
154
142
123
113
439
406
356
328
273
251
240
222
184
169
163
150
125
115
98.9
91.0

686
619
573
513
462
405
376
335
310
275
249
222
206
190
155
142
567
512
474
424
383
335
311
278
257
228
206
184
170
157
129
118
457
412
382
342
308
270
250
224
207
184
166
148
137
127
104
94.9

930
840
770
680
614
563
508
465
420
384
337
308
278
255
235
215
770
695
638
562
508
466
421
385
348
318
279
255
230
211
195
178
620
560
514
453
409
375
339
310
280
256
224
205
185
170
157
143

For Size 555ABRJ (hollow low-speed shaft with shrink disc) the HP rating and torque rating are limited by the shrink disc, see page76 for instructions.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

Rexnord 2014

(131-110) 75

Horsepower & Torque Ratings/Quadruple Reduction


Torque Ratings
Type AB, ABR & ABX Right-Angle Shaft
HighSpeed
Shaft
RPM

Nominal
Ratios
5%

Approx.
LowSpeed
Shaft
RPM

78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5

11.0
10.0
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
9.1
8.3
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
7.5
6.8
6.1
5.5
5.0
4.5
4.1
3.8
3.3
3.0
2.7
2.5
2.2
2.0
1.8
1.6

870

720

580

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

163
169
167
173
168
174
163
176
168
173
164
176
176
153

163
169
166
173
168
174
164
176
169
174
164
176
176
153

163
169
166
172
168
175
164
176
168
174
164
176
176
153

253
253
266
253
242
265
265
254
242
266
253
242
254
242
242
242
253
253
266
253
241
266
266
254
242
266
254
241
254
242
242
242
253
253
266
254
242
265
265
254
242
265
255
242
254
242
242
242

381
381
385
386
381
387
391
387
388
381
386
386
387
385
390
391
382
381
385
387
381
387
391
387
388
381
385
387
387
384
390
391
381
381
385
387
381
387
390
387
388
382
384
386
387
385
389
389

606
592
549
593
606
593
593
593
607
593
594
593
594
593
593
502
605
592
549
593
606
593
593
594
607
593
594
594
594
594
595
501
606
593
549
593
608
593
593
593
608
593
593
593
594
595
595
502

836
857
854
856
846
860
853
860
844
861
786
861
770
788
769
769
839
861
849
860
843
861
854
861
845
861
788
861
769
788
769
771
844
860
853
861
845
861
855
862
846
861
788
862
769
787
769
772

1270
1264
1268
1268
1270
1264
1275
1272
1270
1269
1272
1269
1273
1269
1272
1273
1274
1265
1271
1269
1269
1269
1271
1269
1272
1269
1272
1270
1273
1271
1274
1273
1275
1264
1275
1272
1270
1269
1272
1269
1272
1268
1272
1271
1273
1271
1274
1272

1892
1891
1895
1894
1892
1898
1899
1896
1904
1904
1893
1897
1897
1900
1900
1841
1891
1891
1895
1901
1895
1899
1900
1893
1897
1900
1906
1900
1899
1901
1901
1842
1892
1897
1892
1902
1892
1894
1899
1907
1892
1900
1900
1901
1902
1900
1902
1845

2362
2197
2446
2202
2201
2205
2451
2199
2206
2205
2201
2198
2213
2148
2147
2148
2360
2196
2443
2198
2204
2198
2454
2210
2206
2209
2200
2210
2206
2149
2149
2148
2365
2204
2450
2202
2209
2205
2446
2205
2206
2198
2206
2208
2208
2149
2151
2149

2454
2707
2730
2739
2739
2740
2732
2746
2747
2445
2742
2746
2751
2465
2468
2462
2452
2704
2730
2741
2743
2745
2729
2744
2748
2464
2758
2744
2744
2460
2463
2462
2449
2700
2727
2743
2752
2745
2726
2746
2741
2473
2758
2746
2750
2464
2461
2464

3129
3213
3051
3131
3149
3121
3054
3132
3147
3124
3128
3138
3157
3126
3146
2712
3131
3215
3049
3134
3149
3119
3048
3135
3157
3118
3137
3136
3145
3130
3154
2716
3129
3207
3054
3131
3157
3116
3048
3137
3154
3117
3120
3129
3157
3131
3153
2715

3723
3728
3738
3747
3468
3477
3768
3778
3486
3490
3795
3794
3512
3514
3527
3528
3741
3743
3757
3759
3478
3483
3777
3793
3505
3514
3794
3807
3513
3526
3542
3542
3755
3765
3773
3770
3498
3500
3789
3801
3512
3511
3819
3811
3540
3545
3536
3541

3897
3864
3901
3904
3875
3866
3942
3898
3934
3933
3942
3900
3946
3937
3576
3587
3892
3862
3899
3898
3882
3864
3940
3909
3941
3940
3940
3906
3935
3931
3597
3602
3894
3858
3901
3904
3875
3866
3932
3910
3940
3947
3942
3900
3937
3948
3599
3596

5449
5448
5491
5399
5396
5463
5457
5492
5460
5488
5465
5491
5456
5495
5485
5489
5451
5446
5497
5392
5395
5464
5464
5494
5466
5492
5467
5494
5454
5494
5499
5491
5449
5448
5498
5395
5392
5458
5462
5492
5460
5488
5449
5482
5446
5495
5497
5476

Torque is in pound-inches at low-speed shaft multiply values listed by 1000.


For Size 555ABRJ drives (hollow low-speed shaft with shrink disc connection), the maximum output torque rating is limited to 3,100,000 lb-in by the shrink disc, and this shrink disc
torque rating supersedes any higher torque ratings for the 555 that may be shown on torque pages70, 72, 74 and 76. In those cases where your 555ABRJ is selected
at a High-Speed Shaft RPM and Nominal Ratio where the torque rating of the gear drive is limited by the shrink disc (3,100,000 lb-in), you must calculate an Equivalent Power Rating
(HP) for the 555ABRJ gear drive using the formula below:
3,100,000 lb-in

x Power Rating (HP) from pages69, 71, 73 or 75 = Equivalent Power Rating (HP)

Torque Rating (lb-in) from pages70, 72, 74 or 76

Availability of Types AB / ABR / ABX Triple & Quadruple Reduction


High-Speed
Shaft RPM

Type

385

405

425

445

465

485

505

525

535

545

555

565

585

All

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

76 (131-110)

Rexnord 2014

Type AB Technical Data and Dimensions


Basic Thermal Horsepower Ratings
Double Reduction
Type AB Basic Thermal Horsepower Ratings
Nominal
Ratios

High-Speed
Shaft RPM

1750

1430

1170
5.06 thru
6.86
870

720

580

1750

1430

1170
7.59 thru
10.29
870

720

580

1750

1430

1170
11.39 thru
17.09
870

720

580

Drive Size

Auxiliary
Cooling

385

405

425

445

465

485

505

525

None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes

103
210
472
523
114
201
456
493
120
191
438
461
123
174
410
414
122
163
392
385
120
153
371
353
98.8
192
409
434
105
180
393
407
108
168
375
378
107
151
349
338
106
141
332
313
102
131
314
287
86.2
160
326
326
88.5
148
310
303
88.5
136
294
281
86.1
121
271
249
83.7
112
258
230
80.6
101
243
218

130
290
641
854
149
277
621
803
158
261
598
750
163
239
561
671
162
225
538
622
159
209
510
569
128
266
553
702
137
249
531
652
142
230
507
605
142
208
472
538
140
193
450
497
136
178
425
453
114
226
450
536
118
208
429
497
119
191
407
460
116
169
376
405
113
156
358
374
109
143
338
340

119
365
786
1140
155
353
772
1082
177
336
751
1018
192
310
713
917
195
293
686
853
195
273
656
783
126
335
675
927
148
316
656
867
160
295
633
817
168
266
596
731
167
249
572
678
164
230
543
621
117
278
529
679
127
256
508
634
132
235
487
589
133
209
453
524
131
193
433
483
127
177
410
441

212
605
1209
2109
256
573
1181
1986
283
538
1144
1863
299
487
1082
1669
301
456
1040
1551
298
422
991
1416
215
542
1010
1622
238
499
973
1475
249
459
934
1410
253
407
874
1256
250
377
835
1159
245
346
792
1058
192
450
803
1206
202
408
768
1115
205
371
731
1037
204
323
679
915
199
297
646
843
192
271
610
765

257
670
2146
2568
315
654
2071
2450
347
628
1990
2309
370
582
1867
2104
373
550
1815
1963
371
515
1702
1810
263
647
1843
2121
298
608
1764
2004
316
570
1685
1874
325
514
1571
1692
324
480
1499
1575
318
443
1421
1440
250
576
1490
1639
266
527
1415
1528
271
482
1343
1422
269
424
1241
1265
264
392
1180
1176
256
358
1115
1066

201
665
1942
2145
264
637
1887
2057
301
604
1823
1945
329
553
1724
1775
336
521
1658
1669
337
485
1584
1534
192
557
1531
1622
229
522
1476
1540
251
488
1418
1445
266
439
1330
1310
267
410
1275
1225
264
379
1213
1124

280
794
2126
2298
336
752
2065
2192
380
686
1962
2015
392
645
1891
1898
396
599
1809
1763

273
710
1814
1874
309
662
1751
1780
335
594
1653
1628
340
554
1588
1522
339
511
1515
1410

426
1120
2963
3443
488
1054
2872
3308
537
955
2724
3067
549
895
2627
2897
552
831
2514
2703

401
989
2503
2820
441
917
2411
2685
467
818
2272
2497
472
761
2183
2321
469
701
2083
2162

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.

Rexnord 2014

(131-110) 77

Basic Thermal Horsepower Ratings


Triple Reduction
Type AB, ABR & ABX Basic Thermal Horsepower Ratings
Nominal
Ratios

High-Speed
Shaft RPM

Auxiliary
Cooling

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

None
125
140
210
235
257

Shaft Fan
188
236
363
446
560
1750

414
485
515

Electric Fan

404
529
787
984 1199 298
Cooling Tubes

354
757 1026 1269 1910

None
122
142
209
243
284

Shaft Fan
173
219
332
412
520
1430

454
531
565
636
811
Electric Fan

385
504
748
930 1152 333
Cooling Tubes

311
708
960 1181 1804

None
116
142
208
245
293

Shaft Fan
156
204
308
380
484
1170

473
553
589
662
845
Electric Fan

359
477
705
885 1104 352
13.95
Cooling Tubes

288
651
878 1082 1645

None
101
137
201
244
299
thru 17.09

Shaft Fan
130
183
270
338
432
870

477
559
594
669
854
Electric Fan

321
436
650
819 1029 360
Cooling Tubes

292
555
762
951 1469

None
97.7 123
193
235
296

Shaft Fan
121
160
250
314
405
720

473
553
589
662
845
358
Electric Fan

305
406
611
776
972
Cooling Tubes

270
570
695
878 1375

None
94.8 122
174
209
284

Shaft Fan
113
147
222
274
378
580

461
540
573
646
825
351
Electric Fan

287
385
572
724
937
Cooling Tubes

250
517
717
894 1257
85.4
112
126
187
213
242
291
388
None
207
316
388
491
823
128
166
631
Shaft Fan
1750
412
483
514

Electric Fan
278
357
454
670
831
1026
2313
1802
Cooling Tubes
234
294
624
837
1026
1551
2162
1839
79.0
103
125
185
215
254
311
409
None
113
146
189
287
354
452
754
Shaft Fan
581
1430
435
509
541
609
777
Electric Fan
257
329
428
632
787
980
2193
1712
Cooling Tubes
224
284
572
769
948
1445
2045
1722
76.6
99.5
118
180
214
258
319
416
None
104
133
169
261
325
415
693
Shaft Fan
535
1170
442
517
550
619
790
Electric Fan
242
308
400
595
774
934
2078
1624
18.91 thru
Cooling Tubes
206
260
544
703
874
1343
1910
1616
69.0
89.5
115
166
199
243
318
412
None
38.44
88.3
114
151
225
279
357
611
Shaft Fan
474
870
438
512
545
613
782
Electric Fan
219
278
368
540
680
856
1918
1501
Cooling Tubes
194
246
475
643
802
1243
1722
1444
67.3
86.6
106
161
195
241
302
404
None
83.1
106
136
208
260
334
566
Shaft Fan
430
720
429
502
534
601
767
Electric Fan
207
263
345
511
646
818
1822
1418
Cooling Tubes
179
227
462
590
740
1152
1604
1392
64.9
82.5
104
149
181
236
29
380
None
77.2
98.3
127
187
232
309
509
Shaft Fan
398
580
404
473
503
566
722
Electric Fan
194
247
325
476
603
775
1708
1340
Cooling Tubes
163
206
417
571
714
1051
1540
1280
85.4
95.9
139
180
207
256
354
60.8
None
90.7
126
155
235
309
386
683
Shaft Fan
498
1750
376
440
468

Electric Fan
197
270
338
497
639
771
1814
1331
Cooling Tubes
162
221
444
599
720
1065
1610
1256
56.2
77.8
94.8
137
165
190
256
352
None
79.6
109
142
214
268
333
614
Shaft Fan
449
1430
374
438
466
524
669
Electric Fan
181
248
318
467
591
715
1705
1251
Cooling Tubes
156
216
406
549
687
1020
1498
1162
53.8
74.9
87.8
135
162
191
238
325
None
73.1
101
126
194
245
305
536
Shaft Fan
392
1170
346
405
431
484
618
Electric Fan
170
232
295
439
558
678
1586
1165
2.54 thru
631
944
1434
Cooling Tubes
143
198
388
502
1116
51.5
70.2
84.8
123
150
177
233
319
None
78.16
64.4
88.9
112
166
209
259
470
Shaft Fan
345
870
339
397
423
476
607
Electric Fan
154
211
271
397
506
617
1457
1070
Cooling Tubes
126
173
339
461
581
877
1294
993
None s
49.1
67.3
82.5
119
147
175
219
311
Shaft Fan l
60.3
81.9
104
154
194
242
434
309
720
331
387
412
463
591
Electric Fan
146
199
256
376
480
589
1381
1005
Cooling Tubes
115
159
310
422
535
810
1200
962
46.2
63.8
79.0
113
141
170
214
290
None
55.0
74.9
95.9
142
178
223
387
Shaft Fan
285
580
308
360
383
431
550
Electric Fan
136
186
241
352
451
556
1289
946
Cooling Tubes
105
143
280
381
485
739
1155
880
Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
For Type ABX, apply a multiplier of 0.8 to thermal ratings with no auxiliary cooling.
For Type ABX, apply a multiplier of 0.9 to thermal ratings with shaft fan.
Ratings shown for shaft fan, electric fan and cooling tubes apply to Size 505AB only. Consult Factory for 505ABR and 505ABX.
Triple reduction sizes and ratios are offered for Types ABR and ABX only.
13.95 is not available for Size 555.

78 (131-110)

Rexnord 2014

Basic Thermal Horsepower Ratings


Quadruple Reduction
Type AB, ABR & ABX Basic Thermal Horsepower Ratings
Nominal
Ratios

High-Speed
Shaft RPM

1750

1430

1170
78.16 thru
158.9
870

720

580

1750

1430

1170
175.9 thru
357.5
870

720

580

Drive Size

Auxiliary
Cooling

385

405

425

445

465

485

505

525

None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes
None
Shaft Fan
Electric Fan
Cooling Tubes

48.6

156

46.8

146

45.0

136

41.5

123

39.8

116

37.4

108

38.6

122

37.4

113

35.1

105

32.2

95.4

31.0

89.5

28.7

83.1

60.8

192

58.5

180

56.2

167

51.5

151

48.6

142

45.6

132

49.1

150

46.2

140

43.9

129

40.4

116

37.4

109

35.1

101

81.3
120
278

79.6
111
261

77.2
101
245

72.5
90.0
223

69.6
84.0
209

65.5
77.0
196

62.6
89.5
201

60.3
81.3
187

56.7
73.7
175

52.7
64.9
158

50.3
60.0
148

47.4
54.4
138

111
163
385
313
108
150
361
289
105
137
339
266
98.9
122
309
234
94.2
113
291
216
88.9
104
272
197
87.8
125
285
215
83.1
113
266
197
79.6
102
249
181
73.1
90.7
225
159
69.6
83.0
211
146
65.5
76.6
197
133

129
204
484
387
129
188
456
359
127
174
428
331
121
154
391
293
116
143
369
270
111
131
345
246
106
160
367
269
103
146
342
248
98.3
133
321
228
91.8
116
290
201
87.2
108
273
185
83.1
100
254
167

161
273
644
504
164
253
610
472
164
235
577
440
159
209
531
394
155
195
503
365
148
181
472
334
139
222
498
364
136
202
467
338
132
184
439
313
125
161
400
277
120
150
377
256
113
137
352
233

242
398
1181
628
209
335
1080
606
210
309
1015
566
205
276
926
506
198
256
873
469
190
235
817
430
185
308
916
487
182
278
854
452
177
253
798
418
167
221
723
370
159
204
679
343
152
186
633
312

290
480
1429
729
253
407
1310
697
255
376
1234
654
249
335
1128
588
241
312
1065
548
232
288
999
504
223
371
1103
559
220
337
1029
521
214
307
962
482
202
268
873
430
192
247
823
398
183
226
768
364

535

545

555

565

585

307

363

380

442

550

270

317

333

386

481

271

319

336

389

484

264

311

327

379

472

257

302

318

368

458

246

290

305

353

440

239

280

296

341

424

234

275

289

335

418

228

267

281

326

405

215

253

266

308

383

205

241

253

294

365

194

229

240

278

347

Basic thermal ratings in HP are shown for an ambient temperature of 80F (27C) and at an altitude of sea level to 2500 feet. For other ambient temperatures, other altitudes, or
special air velocity / inlet water temperature / duty cycle considerations, use thermal factors on page9 to determine an application-adjusted thermal rating which can then be
compared to the actual power transmitted. Thermal ratings for cooling tubes are based on water inlet temperature of 70F (21C), and water flow rates as shown on page11. For
cooling capacity exceeding the methods listed for the gear drive size, ratio and high-speed shaft RPM that you have selected, consult your Rexnord representative for an external heat
exchanger package.
For Type ABX, apply a multiplier of 0.8 to thermal ratings with no auxiliary cooling.
For Type ABX, apply a multiplier of 0.9 to thermal ratings with shaft fan.
Ratings shown for shaft fan, electric fan and cooling tubes apply to Size 505AB only. Consult Factory for 505ABR and 505ABX.

Rexnord 2014

(131-110) 79

Overhung Loads
Type AB, ABR & ABX

Consult Factory for Higher Overhung Load Ratings In many cases, overhung
load capacity in excess of that published is available. If the actual load should exceed
the published capacity, refer full details to the Factory; provide complete application
information (see page8), as well as direction of rotation, location and direction of
applied load.

High & Low-Speed Shaft


Overhung Load (lb)=

SEAL
CAGE

126,000 HP x Fc x Lf
Pitch Dia (in) x RPM

Low-Speed Shaft

Fc = Load Connection Factor.


CENTERLINE
Sprocket
OF LOAD
Machined Pinion & Gear
Synchronous (Timing) Belt
V-Belt
Flat Belt

Calculate low-speed shaft overhung load using the formula and Fc values at left. The Lf
load location factors tabulated below are based on the distance from the centerline of the
load to the gear drive seal cage.

1.00
1.25
1.30
1.50
2.50

Low speed shaft overhung load example An application requiring 115 hp


is driven by a 385AB2 drive with 100 rpm output. An 18" pitch diameter single-chain
sprocket is mounted on the low-speed shaft and the centerline of the load is 5 inches
from the seal cage. Calculate the overhung load:

Lf = Load Location Factor.


Low-Speed Shaft See table below.
High-Speed Shaft See instructions at right.

DISTANCE

Overhung Load =

Refer all multiple chain sprocket and pinion-mounted applications to the Factory for
deflection analysis.
Overhung Loads Overhung load is imposed upon a shaft when a pinion, sprocket
or sheave is used as a power take-off. The magnitude of the load varies with the type of
take-off and its proximity to the shaft bearing. Calculate the load (including minimum
required service factor) and check the result against the tabulated overhung load rating.
The above overhung load formula considers the transmitted power rating, without service
factor. This is appropriate for applications where starting loads, momentary overloads
and brake capacities do not exceed 200% of drive rating (100% overload). For other
conditions, compute the equivalent power by multiplying the transmitted power by the
appropriate service factor.
Locate the centerline of the load as close to the gear drive seal cage as practical to
minimize the effect of the overhung load and increase bearing life.
Type AB

126,000 x 115 x 1.0 x 1.05


= 8453 pounds
18 x 100

Refer to the Type AB2 table on page83 and note that the overhung load capacity for a
385AB2 at 100 rpm is 12,500 pounds (12.5 x 1000) and is satisfactory for this selection.
High-Speed Shaft
High-speed shaft overhung load ratings published on pages81 and 82 are for
normal conditions where the centerline of the load is one shaft diameter from the seal
cage, and for speeds of 1170 rpm or lower. Where the centerline of the load is one
shaft diameter or closer, calculate the high-speed shaft overhung load using Lf = 1 in
the formula above left. Check the result against the rating on pages81 and 82.
Higher overhung load capacities are available when the full gear drive torque rating is not
utilized. Refer to the Factory for higher ratings for these conditions or if the calculated
load (using Lf = 1) exceeds the published value or if the load is applied at a distance
greater than one shaft diameter from the high-speed shaft seal cage.
Type AB, ABR & ABX

Lf Load Location Factors

Lf Load Location Factors

Based on distance from centerline of load to gear drive seal cage.

Based on distance from centerline of load to gear drive seal cage.

Low-Speed Shaft

Distance
(in)

2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
10
11
12
13
14
15
16
17
18

385

405

425

0.89
0.91
0.93
0.96
0.98
1.00
1.05
1.11
1.16
1.22
1.27
1.33

0.87
0.90
0.92
0.94
0.96
0.98
1.00
1.05
1.10
1.15
1.20
1.26
1.31
1.36

0.86
0.88
0.90
0.91
0.93
0.95
0.97
0.99
1.02
1.07
1.12
1.16
1.21
1.25
1.30
1.39

Low-Speed Shaft
Double Reduction
Drive Size
445
465

0.86
0.87
0.89
0.90
0.92
0.94
0.95
0.97
0.98
1.00
1.04
1.09
1.13
1.17
1.22
1.30
1.39

Centerline of load is beyond end of


standard low-speed shaft. Consult
Factory for special shaft.

0.85
0.86
0.87
0.89
0.90
0.92
0.93
0.95
0.96
0.98
0.99
1.02
1.06
1.10
1.14
1.22
1.30
1.38

485

505

525

0.81
0.83
0.84
0.86
0.87
0.88
0.90
0.91
0.93
0.94
0.96
0.97
0.99
1.00
1.04
1.11
1.18
1.25
1.32
1.39

0.81
0.82
0.84
0.85
0.86
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.97
0.98
0.99
1.05
1.12
1.18
1.25
1.32
1.39
1.45

0.80
0.81
0.82
0.83
0.85
0.86
0.87
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.96
0.99
1.03
1.09
1.15
1.21
1.27
1.33
1.39
1.45

Interpolate for intermediate values. For example, Lf is 0.96 for a Size 425AB2 when
the distance is 4.75 inches.

Distance
(in)

2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Triple & Quadruple Reduction


Drive Size
385 405 425 445 465 485 505 525 535 545 555 565 585

0.87
0.90
0.92
0.95
0.97
1.00
1.05
1.11
1.16
1.22
1.27
1.33

0.86
0.88
0.91
0.93
0.95
0.98
1.00
1.05
1.10
1.15
1.20
1.26
1.31
1.36

0.84
0.86
0.88
0.91
0.93
0.95
0.97
0.99
1.02
1.07
1.12
1.16
1.21
1.26
1.30
1.40

0.83
0.85
0.87
0.89
0.91
0.92
0.94
0.96
0.98
1.00
1.04
1.09
1.13
1.17
1.22
1.30
1.39

0.82
0.84
0.85
0.87
0.89
0.91
0.92
0.94
0.96
0.97
0.99
1.02
1.06
1.10
1.14
1.22
1.30
1.38

0.82
0.83
0.85
0.86
0.88
0.89
0.91
0.92
0.94
0.95
0.97
0.98
1.00
1.03
1.07
1.14
1.21
1.27
1.34
1.41

0.81
0.82
0.84
0.85
0.86
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.97
0.98
0.99
1.05
1.12
1.18
1.25
1.32
1.39
1.45

Centerline of load is beyond end of


standard low-speed shaft. Consult

Factory for special shaft.

0.80
0.81
0.82
0.83
0.85
0.86
0.87
0.88
0.89
0.90
0.92
0.93
0.94
0.95
0.96
0.99
1.03
1.09
1.15
1.21
1.27
1.33
1.39
1.45

0.77
0.79
0.80
0.81
0.83
0.84
0.85
0.87
0.88
0.89
0.91
0.92
0.93
0.95
0.96
0.99
1.03
1.09
1.15
1.20
1.26
1.32
1.38
1.44

0.80
0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.96
0.99
1.02
1.07
1.13
1.18
1.24
1.29
1.34
1.40
1.45

0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.95
0.97
0.99
1.03
1.08
1.13
1.18
1.23
1.28
1.33
1.39
1.44

0.81
0.82
0.83
0.84
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0.91
0.92
0.93
0.94
0.96
0.98
1.00
1.04
1.09
1.14
1.19
1.25
1.30
1.35
1.40
1.45

0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.87
0.88
0.89
0.90
0.91
0.92
0.92
0.93
0.95
0.97
0.98
1.00
1.05
1.10
1.15
1.19
1.24
1.29
1.34
1.39
1.44
1.48

Interpolate for intermediate values. For example, Lf is 0.99 for a Size 405AB3 when
the distance is 4.75 inches. Consult Factory for Type ABXQ.

80 (131-110)

Rexnord 2014

Overhung Loads
High-Speed Shaft
Type AB Overhung Loads Double Reduction (lbs)
High-Speed
Shaft RPM

Nominal
Ratios 4%

Approx. LowSpeed Shaft


RPM

385

405

425

445

465

485

505

525

5.06

230

1600

2000

2500

3000

1450

1170

870

720

580

Drive Size

5.60

210

1600

2000

2500

3000

1450

6.20

190

1600

2000

2500

3000

1450

6.86

170

1600

2000

2500

3000

1450

7.59

155

1600

2000

2500

3000

1790

4000

4700

5400

8.40

140

1600

2000

2500

3000

2620

4000

4700

5400

9.30

125

1600

2000

2500

3000

3340

4000

4700

5400

10.29

115

1600

2000

2500

3000

3080

4000

4700

5400

11.39

100

1600

2000

2500

3000

3500

4000

4700

5400

5.06

175

1600

2000

2500

3000

1980

5.60

155

1600

2000

2500

3000

1980

6.20

140

1600

2000

2500

3000

1980

6.86

130

1600

2000

2500

3000

1980

7.59

115

1600

2000

2500

3000

1980

4000

4700

5400

8.40

105

1600

2000

2500

3000

3030

4000

4700

5400

9.30

95

1600

2000

2500

3000

3500

4000

4700

5400

10.29

85

1600

2000

2500

3000

3430

4000

4700

5400
5400

11.39

77

1600

2000

2500

3000

3500

4000

4700

5.06

140

1600

2000

2500

3000

2420

5.60

130

1600

2000

2500

3000

2580

6.20

115

1600

2000

2500

3000

2420

6.86

105

1600

2000

2500

3000

2420

7.59

95

1600

2000

2500

3000

2420

4000

4700

5400

8.40

85

1600

2000

2500

3000

3500

4000

4700

5400

9.30

77

1600

2000

2500

3000

3500

4000

4700

5400

5.06

115

1600

2000

2500

3000

3100

5.60

105

1600

2000

2500

3000

3340

6.20

95

1600

2000

2500

3000

3010

6.86

85

1600

2000

2500

3000

3010

7.59

77

1600

2000

2500

3000

3080

4000

4700

5400

8.40

70

1600

2000

2500

3000

3500

4000

4700

5400

Type AB, ABR & ABX Overhung Loads Quadruple Reduction (lbs)
HighSpeed
Shaft
RPM

1170

870
720
580

Nominal
Ratios
5%

Approx.
Low-Speed
Shaft
RPM

385

405

425

445

465

485

505

525

535

545

555

565

585

78.16

15.0

1300

910

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

3950

Drive Size

86.50

13.5

700

980

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4500

95.73

12.0

700

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

78.16

11.0

1300

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

86.50

10.0

700

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

78.16

9.1

1300

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

86.50

8.3

700

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

78.16

7.5

1300

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

86.50

6.8

700

1000

1300

1600

2000

2500

3000

3500

3500

4000

4000

4700

4700

For loads applied one shaft diameter from seal cage and speeds of 1170 RPM or lower. In each High-Speed Shaft RPM section, the last overhung load value applies to all of the higher
ratios of that gear reduction. Published ratings are based on a combination of the most unfavorable conditions of loading. Consult Factory for ratings of drives with fans.
Size 385 rating at 78.16:1 is for triple reduction.

Rexnord 2014

(131-110) 81

Overhung Loads
High-Speed Shaft
Type AB, ABR & ABX Overhung Loads Triple Reduction (lbs)
HighNominal Approx. LowSpeed
Ratios Speed Shaft
Shaft RPM
4%
RPM

1170

870

720

580

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82

84
75
68
60
56
50
45
40
37
34
30
27
25
22
20
18.0
62
55
50
45
42
38
34
31
28
25
22
21
18.0
17.0
15.0
14.0
50
45
42
38
34
31
28
25
22
21
18.0
17.0
15.0
14.0
12.5
11.0
42
38
34
31
28
25
22
21
18.0
17.0
15.0
14.0
12.5
11.0
10.0
9.1

Drive Size
385

405

425

445

465

485

505

525

535

545

555

565

585

1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300

1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300

1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300

1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300

1450
1450
1450
1590
1470
1590
1600
1600
1600
1510
1510
1590
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1410
1410
1550
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1350
1350
1540
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1300
1300
1530
1600
1600
1600
1600

2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000
2000

2500
2500
2500
2500
2500
2500
2500
2500
2500
2160
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
1880
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
1650
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
1520
2500
2500
2500
2500
2500
2500

3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000

2650
2650
2730
2730
2730
2730
3060
3340
3500
3500
3350
3500
3500
3500
3500
3500
3150
3150
3360
3360
3360
3360
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500

3410
3410
3410
3410
3730
3730
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000

1450
1460
1630
2500
3210
2920
3060
4380
4700
3710
3710
4670
4700

1980
2290
2550
3340
4060
3230
3920
4700
4700
4480
4480
4700
4700

2450
2890
3170
3930
4650
3840
4520
4700
4700
4220
4220
4700
4700

3220
3610
3920
4660
4700
4590
4700
4700
4700
3860
3860
4700
4700

1450
1450
1450
1450
1450
1630
1630
2540
3210
3000
3110
4410
4700
3710
3710
4700
1980
1980
1980
1980
1980
2550
2550
3390
4060
3860
3970
4700
4700
4480
4480
4700
2420
2420
2420
2440
2440
3170
3170
3980
4660
4460
4560
4700
4700
4220
4220
4700
3010
3010
3010
3220
3220
3920
3920
4700
4700
4700
4700
4700
4700
3860
3860
4700

5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400

5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400

5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400

5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400

5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400
5400

1990
1990
1990
1990
1990
3840
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
4940
4940
4940
4940
4940
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000

6000
6000
6000
6000
6000
6000
6000
6000
4760
4760
6000
6000
5690
5690
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
5220
6000
6000
6000
5690
5690
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000
6000

For loads applied one shaft diameter from seal cage and speeds of 1170 RPM or lower. In each High-Speed Shaft RPM section, the last overhung load value applies to all of the higher
ratios of that gear reduction. Published ratings are based on a combination of the most unfavorable conditions of loading. Consult Factory for ratings of drives with fans.

82 (131-110)

Rexnord 2014

Overhung Loads
Low-Speed Shaft
Type AB Overhung Loads Double, Triple & Quadruple Reduction (lbs)
Approx. Low-Speed
Shaft
RPM

385

405

425

445

465

485

505

525

545

565

585

350
310
280
255
230
210
190
170
155
140
125
110
100
93
84
77
70
62 or Lower

12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5

15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0

17.3
17.5
17.8
17.9
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0

22.8
23.4
24.1
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0

23.4
23.2
22.2
24.2
23.6
25.3
25.1
26.9
27.4
28.6
29.1
30.1
32.8
33.0
33.0
33.0
33.0
33.0

40.0
38.4
39.6
38.2
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0
40.0

42.6
48.9
45.9
44.9
49.4
50.0
50.0
50.0
50.0
50.0
42.8
49.9
45.4
50.0

60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0

72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0

86.0
86.0
86.0
86.0
86.0
86.0

100
100
100
100
100
100

Drive Size

Type ABXD Shaft Down (lbs)


Low-Speed Shaft Overhung Load

Type ABXU Shaft Up (lbs)


Low-Speed Shaft Overhung Load
Approx. LowSpeed Shaft
RPM

405

425

445

465

485

505

535

555

125
110
100
93
84
77
70
62
57
50 or Lower

15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0

16.3
16.1
15.1
17.1
16.7
16.5
17.4
18.0
18.0
18.0

22.4
22.3
21.6
21.3
21.9
21.7
22.6
23.0
24.1
25.0

29.6
29.9
29.2
29.4
29.3
30.6
31.1
32.5
33.0
33.0

38.3
38.4
37.3
37.3
35.7
35.3
36.5
36.4
38.3
40.0

45.7
47.6
42.5
44.5
41.7
41.2
44.2
46.3
49.1
50.0

60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0

72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0
72.0

Drive Size

Type ABX Shaft Up or Down (lbs)


Low-Speed Shaft Thrust Capacity (Thrust Up)
Approx. LowSpeed Shaft
RPM

405

425

445

465

485

505

535

555

125
110
100
93
84
77
70
62
57
50 or Lower

11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5

16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5

21.0
20.7
20.3
19.6
19.5
19.9
20.7
21.0
21.0
21.0

25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0

30.0
38.4
37.3
37.3
35.7
35.3
36.5
36.4
38.3
40.0

40.0
40.0
39.5
40.0
38.2
40.0
40.0
40.0
40.0
40.0

50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0

60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0

Drive Size

Approx. LowSpeed Shaft


RPM

405

425

445

465

485

505

535

555

125
115 or Lower

15.0
15.0

18
18

25
25

33
33

40
40

50
50

60
60

72

Drive Size

Type ABX Shaft Up or Down (lbs)


Low-Speed Shaft Thrust Capacity (Thrust Down)
Approx. LowSpeed Shaft
RPM

405

425

445

465

485

505

535

555

125
110
100
93
84
77
70
62
57 or Lower

11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5

16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5

20.7
20.2
19.8
19.1
19.0
19.3
20.1
20.5
21.0

25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0
25.0

30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0

40.0
40.0
38.4
40.0
37.1
40.0
39.4
40.0
40.0

50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0
50.0

60.0
60.0
60.0
60.0
60.0
60.0
60.0
60.0

Drive Size

Published ratings are for standard assemblies with shaft extensions as shown on
page66 and are based on the most unfavorable conditions of loading.
Refer to Factory for higher overhung load capacities and capacities at unlisted
speeds. Furnish complete application information. Published ratings are for
standard assemblies with shaft extension as shown on page66 and are based
on the most unfavorable conditions of loading. For higher ratings and ratings for
the second shaft extension, refer full data to the Factory. Consult Factory for Type
ABXQ.
Multiply values below by 1000.
Published ratings are based on a combination of the most unfavorable conditions
of loading. For higher ratings, refer full data to the Factory. Consult the Factory for
combined radial and thrust loads. Consult Factory for Type ABXQ.

Rexnord 2014

(131-110) 83

Exact Ratios/Right-Angle Shaft Gear Drives


Double Reduction Exact Ratios (Type AB)
Drive Size

Nominal
Ratio

385

405

425

445

465

485

505

525

5.06
5.60
6.20
6.86
7.59
8.40
9.30
10.29
11.39
12.61
13.95
15.44
17.09

4.850
5.413
6.089
6.594
7.170
8.119
9.134
9.890
10.76
12.33
13.87
15.02
16.34

4.961
5.495
6.201
6.716
7.345
7.971
8.996
10.66
10.93
12.11
13.66
14.80
16.19

4.933
5.391
6.216
6.766
7.400
8.143
9.388
10.22
11.18
12.25
14.13
15.38
16.82

5.281
5.707
6.188
6.739
7.812
8.500
9.218
10.04
11.64
12.61
13.68
14.90
17.27

4.902
5.427
6.262
6.567
7.104
8.298
9.575
10.04
10.86
12.53
14.46
15.16
16.40

7.585
8.162
9.400
10.23
11.19
12.24
14.10
15.35
16.79

7.636
8.213
9.545
10.45
11.45
12.21
14.20
15.54
17.04

7.410
8.208
9.262
10.03
10.97
12.37
13.96
15.12
16.54

Except where noted with a footnote (), exact ratios are within 4% of the nominal ratios.
Triple Reduction Exact Ratios (Type AB, ABR & ABX)
Drive Size

Nominal
Ratio

385

405

425

445

465

485

505

525

535

545

555

565

585

13.95
15.44
17.09
18.91
20.93
23.16
25.63
28.36
31.39
34.74
38.44
42.54
47.08
52.11
57.66
63.82
70.62
78.16

18.80
21.15
22.90
24.72
29.10
30.88
33.44
37.07
43.65
46.32
50.16
59.83
65.06
69.03
74.75

14.38
15.99
17.71
18.60
21.65
22.32
25.19
27.28
32.07
33.48
37.78
41.12
48.11
52.62
58.66
66.19
71.69

13.70
14.98
17.27
18.45
21.28
23.16
25.20
27.61
31.97
34.80
37.86
41.49
45.16
52.86
57.52
63.03
68.60

14.41
15.57
16.83
18.19
21.48
22.83
24.76
29.20
31.26
34.25
37.14
43.80
46.89
50.77
56.42
61.45
71.22

13.82
15.30
16.43
18.19
20.99
22.74
26.23
27.52
32.24
34.54
38.06
43.23
46.77
50.10
57.81
65.67
71.04

14.16
15.24
16.72
17.99
20.72
22.55
26.11
28.42
30.93
33.83
39.43
42.92
46.71
51.09
59.33
64.58
70.29

14.61
15.71
18.11
19.47
21.22
22.82
26.52
28.88
31.60
33.99
39.50
43.02
47.10
50.44
58.62
63.84
69.90

19.92
21.57
22.54
25.44
27.55
31.12
34.47
38.90
42.13
46.98
52.04
58.72
61.59
72.16

14.65
16.16
18.13
19.94
22.37
23.09
25.46
28.57
30.89
34.20
38.94
43.69
47.24
51.64
58.78
65.95
71.31

13.45
14.64
16.54
18.08
20.50
22.40
25.07
27.63
31.33
34.24
38.32
41.71
47.00
51.36
57.48
62.57
70.02

14.83
16.40
18.53
20.20
22.52
25.04
27.91
30.38
34.42
38.27
42.66
46.43
51.63
57.41
63.99
69.65

13.80
15.26
17.49
18.99
20.71
22.28
25.89
28.35
31.09
35.64
38.86
42.55
46.24
53.00
57.80
63.28
70.46

13.93
15.15
16.42
17.89
19.62
22.37
24.52
27.46
30.42
33.34
37.63
41.37
45.39
50.27
56.73
62.38
67.56

Except where noted with a footnote (), exact ratios are within 4% of the nominal ratios.
Triple reduction ratios are offered for Types ABR and ABX only.
Quadruple Reduction Exact Ratios (Type AB, ABR & ABX)
Drive Size

Nominal
Ratio

385

405

425

445

465

485

505

525

535

545

555

565

585

70.62
78.16
86.50
95.73
105.9
117.2
129.7
143.6
158.9
175.9
194.6
215.4
238.4
263.8
291.9
323.1
357.5

85.52
92.60
108.5
117.5
126.8
137.3
158.5
171.6
189.0
204.7
236.2
255.7
299.0
325.2

81.14
87.88
99.95
108.3
118.4
125.9
149.0
161.3
176.5
187.7
221.3
242.0
250.7
298.5
321.0
349.4

74.03
86.50
95.23
103.6
111.0
131.5
143.2
153.7
168.4
193.4
210.5
229.0
251.0
281.3
311.5
341.3

76.12
82.54
90.94
107.4
114.2
123.8
134.8
156.0
170.2
184.5
217.6
232.5
253.2
297.7
322.3
345.0

75.46
87.07
90.70
104.7
113.4
130.8
137.8
159.0
172.2
198.7
208.4
235.4
267.0
303.2
328.0
355.2

74.30
85.56
93.13
107.4
116.9
128.3
139.7
161.1
175.4
195.0
212.2
244.8
266.4
288.2
313.7
341.4

79.18
86.45
94.15
108.1
117.7
125.4
136.6
156.8
170.7
190.5
207.5
238.2
259.4
282.1
307.2
356.1

77.49
87.45
97.64
110.2
115.6
126.9
141.6
159.8
181.3
192.7
218.6
242.8
254.7
298.4
328.4
355.2

79.37
87.53
100.0
110.3
115.7
127.0
145.1
160.0
181.5
192.9
218.9
243.1
254.9
286.0
324.6
368.3

75.82
84.85
94.68
106.0
115.3
126.4
141.0
157.8
171.8
187.5
216.0
234.2
254.9
295.7
321.8
360.1

78.74
85.39
97.58
105.8
118.0
128.4
145.3
157.6
175.7
191.2
215.7
233.9
260.7
283.8
329.1
358.2

78.44
86.20
94.01
105.1
115.8
131.8
144.8
160.7
175.2
197.5
218.6
242.6
264.6
286.2
318.6
348.9

71.70
80.91
89.56
98.47
109.6
121.4
134.0
148.3
163.1
179.5
197.4
223.9
246.2
271.0
297.6
322.3
352.5

Except where noted with a footnote (), exact ratios are within 5% of the nominal ratios.
Availability of Types AB / ABR / ABX Triple & Quadruple Reduction
Type

385

405

425

445

465

485

505

525

535

545

555

565

585

AB
ABR
ABX

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X
X

X
X

X
X

84 (131-110)

Rexnord 2014

Type AB Double Reduction


Sizes 385-525
XX
N

SHAFT GUARD
(WHEN REQUIRED)

DRIVE WITH
COOLING FAN
INSPECTION
COVER

O
1.2

E
V
BOTH ENDS

R
Q

Q
M

6-HOLES FOR
U DIA. BOLT

M
L

Dimensions (in)
A

Drive
Size

W/O
Fan

With
Fan

385
405
425
445
465
485
505
525

5.00
5.50
7.00
7.50
7.50
9.00
10.00
11.24

3.06
3.26
4.12
4.38
4.38
5.56
6.32
7.32

7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38

10.06
11.20
12.74
14.50
16.50
19.00
20.50
22.50

20.06
23.00
25.00
27.70
31.00
35.00
38.00
41.00

1.62
2.00
1.62
2.50
2.50
2.50
2.75
2.50

12.50
14.00
15.75
17.50
20.50
22.25
24.00
27.25

8.44
9.20
11.12
12.00
14.00
16.00
17.25
20.00

28.24
32.00
34.74
40.00
46.00
49.50
53.50
59.50

23.76
25.30
27.50
32.20
33.00
35.00
39.50
42.00

10.50
11.25
12.25
14.60
15.00
15.40
17.25
18.50

19.10
20.60
22.90
26.30
28.60
30.70
33.60
37.20

34.60
38.50
44.60
51.18
54.82
62.40
67.10
71.32

5.00
5.50
6.00
7.00
7.00
9.00
10.26
10.50

0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10

Drive
Size

Wt (lb)

XX

385
405
425
445
465
485
505
525

1530
2020
2810
4320
5400
6990
10300
12810

1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250

9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10

44.60
49.70
57.34
65.68
71.32
81.40
87.60
93.82

9.96
10.56
11.78
13.78
14.24
14.36
15.90
17.56

21.10
21.58
23.78
27.18
29.66
31.24
34.60
38.12

High-Speed Shaft
T

Key

2.500
2.750
3.500
3.750
3.750
4.500
5.000
5.500

0.625 x 0.625 x 4.500


0.625 x 0.625 x 5.000
0.875 x 0.875 x 6.000
0.875 x 0.875 x 6.500
0.875 x 0.875 x 6.500
1.000 x 1.000 x 8.000
1.250 x 1.250 x 9.000
1.250 x 1.250 x 10.000

Low-Speed Shaft
S

Key

4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500

1.000 x 1.000 x 6.500


1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000

Drives are for horizontal floor-mounted operation unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for reference only and are subject to
change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000, -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

Rexnord 2014

(131-110) 85

Type AB Triple Reduction


Sizes 385-585
XX
N

SHAFT GUARD
(WHEN REQUIRED)

DRIVE WITH
COOLING FAN
INSPECTION
COVER

A
W

O
1.2

E
V
BOTH ENDS

R
Q

Q
M

6-HOLES FOR
U DIA. BOLT

Dimensions (in)
A

Drive
Size

W/O
Fan

With
Fan

385
405
425
445
465
485
505
525
545
565
585

3.50
3.50
4.50
5.00
5.50
7.00
7.50
7.50
9.00
10.00
11.24

1.88
1.88
2.56
2.76
2.88
4.12
4.38
4.38

7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38
20.12
21.44
22.76

10.24
11.20
12.74
14.50
16.50
19.00
20.50
22.50
24.50
25.50
29.00

Drive
Size

Wt (lb)

385
405
425
445
465
485
505
525
545
565
585

1600
1960
2860
4380
5380
7450
9900
12900
18700
26050
33400

18.96 1.80
16.50
8.44
21.32 2.00
18.40
9.20
24.00 2.75
20.00
10.00
27.70 2.50
23.25
12.00
31.00 2.50
26.50
14.00
35.00 3.50 30.00 15.00
38.00 2.50 34.50 17.50
41.00 3.00 35.50 19.50
45.00 3.00
36.75
21.50
48.00 3.00
39.50
22.50
54.60 3.00
44.50
26.00

High-Speed Shaft
T

Key

1.750
1.750
2.250
2.500
2.750
3.500
3.750
3.750
4.500
5.000
5.500

0.375 x 0.375 x 3.000


0.375 x 0.375 x 3.000
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.625 x 0.625 x 5.000
0.875 x 0.875 x 6.000
0.875 x 0.875 x 6.500
0.875 x 0.875 x 6.500
1.000 x 1.000 x 8.000
1.250 x 1.250 x 9.000
1.250 x 1.250 x 10.000

36.60
40.80
45.50
51.50
58.00
58.50
65.00
71.00
79.50
85.00
95.00

21.00
22.80
24.80
27.40
29.00
33.00
37.00
39.00
44.00
52.00
56.40

9.10
10.00
11.00
12.20
13.00
14.40
16.00
17.00
19.50
23.20
25.40

17.80
19.40
21.60
23.90
26.60
30.70
33.60
37.20
41.90
45.40
49.80

34.92
37.10
43.71
48.60
54.50
62.60
70.70
75.80
85.40
92.10
99.30

5.00
5.50
6.00
7.00
7.00
8.00
8.80
9.00
9.15
11.50
11.50

0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10
2.10
2.35
2.35

XX

1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250
2.250
2.500
2.500

9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10
23.00
25.00
28.00

45.16
48.30
56.45
63.10
71.00
81.60
91.20
98.30
109.90
117.60
128.30

8.60
9.32
10.54
11.38
12.24
14.36
15.90
17.56
20.10
22.25
25.28

19.75
20.34
22.54
24.78
27.64
31.24
34.46
38.12
43.00
46.10
50.90

Low-Speed Shaft
S

Key

4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500
11.500
12.250
13.000

1.000 x 1.000 x 6.500


1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000
3.000 x 2.000 x 17.000
3.000 x 2.000 x 19.000
3.000 x 2.000 x 21.000

Drives are for horizontal floor-mounted operation unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for reference only and are subject to
change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 485: high-speed end of drive Dimension G = 22.50", F = 2.50".
Size 505: high-speed end of drive Dimension G = 25.50".
Size 525: high-speed end of drive Dimension G = 29.50".

86 (131-110)

Rexnord 2014

Type AB Quadruple Reduction


Sizes 385-585
XX
N

B
SHAFT GUARD
(WHEN REQUIRED)
S

DRIVE WITH
COOLING FAN
INSPECTION
COVER

1.2

1.2

E
V

R
Q

Q
M

6-HOLES FOR
U DIA. BOLT

8-HOLES FOR
U DIA. BOLT

G
F

SIZES 385-525

BA

K
SIZES 545-585

Dimensions (in)
A

Drive
Size

W/O
Fan

With
Fan

385
405
425
445
465
485
505
525
545
565
585

3.00
3.00
3.50
3.50
4.50
5.00
5.50
5.50
7.50
7.50
7.50

1.88
1.88
2.56
2.76
2.88
2.88

7.88
8.66
10.06
11.38
12.68
14.88
16.18
18.38
20.12
21.44
22.76

10.24
11.20
12.74
14.50
16.50
19.00
20.50
22.50
24.50
25.50
29.00

18.96
21.32
24.00
27.70
31.00
35.00
38.00
41.00
45.00
48.00
54.60

1.80
2.00
2.75
2.50
2.50
3.50
2.50
3.00
3.00
3.00
3.00

16.50
18.40
20.00
23.25
26.50
30.00
34.50
37.25
23.50
26.50
28.00

8.44
9.20
10.00
12.00
14.00
15.00
17.50
19.50
21.50
22.50
26.00

36.60
40.80
45.50
51.50
58.00
66.00
74.30
80.50
91.00
99.50
108.00

21.00
22.80
24.80
27.40
29.00
33.00
37.00
39.00
44.00
52.00
56.40

9.10
10.00
11.00
12.20
13.00
14.40
16.00
17.00
19.50
23.20
25.40

17.80
19.40
21.60
23.90
26.60
30.70
33.60
37.20
41.90
45.40
49.80

37.20
39.60
45.80
49.89
58.20
64.60
72.00
77.00
92.21
99.31
103.81

5.00
5.50
6.00
7.00
7.00
8.00
8.80
9.00
9.15
11.50
11.50

0.94
1.06
1.06
1.20
1.26
1.50
1.75
2.10
2.10
2.35
2.35

Drive
Size

Wt (lb)

BA

XX

385
405
425
445
465
485
505
525
545
565
585

1580
1960
2870
4430
5410
7870
10560
13600
20600
27600
35100

36.50
40.50
46.00

1.125
1.125
1.250
1.500
1.500
2.000
2.250
2.250
2.250
2.500
2.500

9.80
11.12
12.50
14.50
16.00
18.00
19.75
21.10
23.00
25.00
28.00

47.44
50.80
58.54
64.39
74.70
83.60
92.50
99.50
116.71
124.81
132.81

8.60
9.32
10.54
11.38
12.24
14.36
15.90
17.56
20.10
22.25
25.28

19.75
20.34
22.54
24.78
27.64
31.24
34.46
38.12
43.00
46.10
50.90

High-Speed Shaft
T

Key

1.500
1.500
1.750
1.750
2.250
2.500
2.750
2.750
3.750
3.750
3.750

0.375 x 0.375 x 2.500


0.375 x 0.375 x 2.500
0.375 x 0.375 x 3.000
0.375 x 0.375 x 3.000
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.625 x 0.625 x 5.000
0.625 x 0.625 x 5.000
0.875 x 0.875 x 6.500
0.875 x 0.875 x 6.500
0.875 x 0.875 x 6.500

Low-Speed Shaft
S

Key

4.500
5.000
5.750
6.500
7.250
8.500
9.250
10.500
11.500
12.250
13.000

1.000 x 1.000 x 6.500


1.250 x 1.250 x 7.500
1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 13.000
2.500 x 1.750 x 14.000
2.500 x 1.750 x 16.000
3.000 x 2.000 x 17.000
3.000 x 2.000 x 19.000
3.000 x 2.000 x 21.000

Drives are for horizontal floor-mounted operation unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for reference only and are subject to
change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Single low-speed shaft extension is standard; double extension, as indicated with dimension XX, is an extra charge option.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 485: high-speed end of drive Dimension F = 2.50".
Size 505: high-speed end of drive Dimension F = 2.80".
Size 525: high-speed end of drive Dimension F = 4.50".

Rexnord 2014

(131-110) 87

Type ABR Triple Reduction


Sizes 405-485
B

AH

UA
S D

UA
W
O
INSPECTION
PLUG
(BOTH SIDES)

V
E

AE
CLEARANCE

2.8

LA

LA
UB - DI A. UNC. TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

6-HOLES FOR
X DIA. BOLT
R

2.8

Dimensions (in)
Drive
Size

AE

AH

LA

405
425
445
465
485

3.50
4.50
5.00
5.50
7.00

25.4
28.2
32.9
37.4
40.7

29.10
32.20
35.60
39.20
43.10

9.70
11.00
12.20
14.00
15.90

11.31
12.31
14.62
16.62
18.50

17.65
19.45
21.41
23.16
25.00

1.50
1.50
1.75
1.95
2.29

18.50
21.00
24.00
27.20
26.90

9.20
10.25
12.25
14.10
15.60

40.00
45.00
51.50
58.25
58.38

27.75
31.80
37.00
41.00
46.50

5.7
6.6
6.7
7.7
9.4

12.50
14.50
16.75
18.75
21.00

21.62
24.62
29.25
33.25
37.00

37.10
43.71
48.60
54.50
62.60

5.00
6.00
7.00
7.00
8.00

1.50
1.60
1.81
1.79
2.00

Drive
Size

Key

UA

UB

UC

UD

Key

405
425
445
465
485

5.000
5.750
6.500
7.250
8.000

1.250 x 1.250 x 7.500


1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 12.000

8.66
10.06
11.38
12.68
14.00

0.750
1.125
1.250
1.250
1.500

1.88
2.25
2.50
2.50
3.00

3.50
3.50
4.00
4.75
5.00

1.750
2.250
2.500
2.750
3.500

0.375 x 0.375 x 3.000


0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.625 x 0.625 x 5.000
0.875 x 0.875 x 6.000

Low-Speed Shaft

High-Speed Shaft

Wt (lb)

9.70
10.60
11.70
12.60
13.60

48.41
56.02
63.22
71.12
81.10

1.125
1.250
1.500
1.500
2.000

41.12
46.01
52.67
59.43
59.50

2310
3282
4576
6806
8576

Drives are for horizontal output shaft operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465: low-speed end of drive Dimension F = 1.90".
Size 425: low-speed end of drive Dimension LA = 6.7".
Size 485: low-speed end of drive Dimension LA = 9.5".

88 (131-110)

Rexnord 2014

Type ABR Triple Reduction


Sizes 505-555
AH

UA

UA
W

INSPECTION PLUG
(BOTH SIDES)

V
E

AE
CLEARANCE

GA

3-HOLES EQUALLY SPACED


UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

L M
N

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

G
K

KA

Dimensions (in)
Drive
Size

505

535
555

Drive
Size

505

535
555

AE

AH

GA

KA

7.50
7.50
9.00

43.7
50.8
55.6

47.62
52.00
59.30

17.32
19.50
21.80

19.62
22.62
24.62

27.87
30.00
34.95

27.00
31.75
35.00

10.00

13.50
16.50
18.00

64.62
74.25
81.75

18.88
21.75
23.75

50.50
56.50
61.50

22.75
25.75
28.25

39.25
45.25
49.25

70.71
77.80
87.40

10.50
10.50
12.00

2.25
2.25
2.31

High-Speed Shaft

Low-Speed Shaft
S

Key

UA

UB

UC

UD

9.250
10.500
11.500

2.500 x 1.750 x 14.00


2.500 x 1.750 x 16.00
3.000 x 2.000 x 17.00

16.18
18.38
20.12

1.500
1.500
1.750

3.00
3.00
3.50

6.00
7.50
8.00

Key

3.750 0.875 x 0.875 x 6.50 15.16


3.750 0.875 x 0.875 x 6.50 16.25
4.500 1.000 x 1.000 x 8.50 18.75

Wt (lb)

90.33
100.42
112.02

2.250
2.250
2.250

65.83
75.92
83.32

12,250
16,650
23,100

Gear drives are for horizontal output shaft operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Add 1.00" to dimensions K, KA, D, W & Y for Size 505ABRJ drive.

Rexnord 2014

(131-110) 89

Type ABR Quadruple Reduction


Sizes 405-485
B

AH

UA
S D

UA
W
O
INSPECTION
PLUG
(BOTH SIDES)

V
E

AE
CLEARANCE

2.8

LA

LA
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

T
6-HOLES FOR
X DIA. BOLT
R

2.8

Dimensions (in)
Drive
Size

AE

AH

LA

405
425
445
465
485

3.00
3.50
3.50
4.50
5.00

25.4
28.2
32.9
37.4
40.7

29.10
32.20
35.60
39.20
43.10

9.70
11.00
12.20
14.00
15.90

11.31
12.31
14.62
16.62
18.50

17.65
19.45
21.41
23.16
25.00

1.50
1.50
1.75
1.95
2.41

18.50
21.00
24.00
27.20
30.60

9.20
10.25
12.25
14.10
15.60

40.00
45.00
51.50
58.25
56.90

27.75
31.80
37.00
41.00
46.50

5.7
6.6
6.7
7.7
9.4

12.50
14.50
16.75
18.75
21.00

21.62
24.62
29.25
33.25
37.00

39.60
45.80
49.89
58.20
64.60

5.00
6.00
7.00
7.00
8.00

1.50
1.60
1.81
1.79
2.00

Drive
Size

Key

UA

UB

UC

UD

Key

405
425
445
465
485

5.000
5.750
6.500
7.250
8.000

1.250 x 1.250 x 7.500


1.500 x 1.500 x 8.000
1.500 x 1.500 x 10.000
1.750 x 1.500 x 11.000
2.000 x 1.500 x 12.000

8.66
10.06
11.38
12.68
14.00

0.750
1.125
1.250
1.250
1.500

1.88
2.25
2.50
2.50
3.00

3.50
3.50
4.00
4.75
5.00

1.500
1.750
1.750
2.250
2.500

0.375 x 0.375 x 2.500


0.375 x 0.375 x 3.000
0.375 x 0.375 x 3.000
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500

Low-Speed Shaft

High-Speed Shaft

Wt (lb)

9.70
10.60
11.70
12.60
13.60

50.91
58.11
64.51
74.82
83.10

1.125
1.250
1.500
1.500
2.000

41.12
46.01
52.67
59.43
67.04

2458
3286
4543
6863
9057

Drives are for horizontal output shaft operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Size 465: low-speed end of drive Dimension F = 1.90".
Size 485: low-speed end of drive Dimension F = 2.29".
Size 425: low-speed end of drive Dimension LA = 6.7".
Size 485: low-speed end of drive Dimension LA = 9.5".

90 (131-110)

Rexnord 2014

Type ABR Quadruple Reduction


Sizes 505-555
AH

S D

UA

UA

W
INSPECTION PLUG
(BOTH SIDES)

V
E

AE
CLEARANCE

GA

L M

3-HOLES EQUALLY SPACED


UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

A
N
T

GA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

G
K

KA

Dimensions (in)
Drive
Size

505

535
555

Drive
Size

505

535
555

AE

AH

GA

KA

5.50
5.50
7.50

43.7
50.3
54.0

47.62
52.00
59.30

17.32
19.50
21.80

19.62
22.62
24.62

27.87
30.00
34.95

31.00
35.75
40.00

8.00

13.50
16.50
18.00

72.90
82.25
92.75

18.88
21.75
23.75

50.50
56.50
61.50

22.75
25.75
28.25

39.25
45.25
49.25

72.02
79.02
94.21

10.50
10.50
12.00

2.25
2.25
2.31

Low-Speed Shaft

High-Speed Shaft

Key

UA

UB

UC

UD

9.250
10.500
11.500

2.500 x 1.750 x 14.00


2.500 x 1.750 x 16.00
3.000 x 2.000 x 17.00

16.18
18.38
20.12

1.500
1.500
1.750

3.00
3.00
3.50

6.00
7.50
8.00

Key

2.750 0.625 x 0.625 x 5.00 15.16


2.750 0.625 x 0.625 x 5.00 16.25
3.750 0.875 x 0.875 x 6.50 18.75

Wt (lb)

91.64
101.64
118.83

2.250
2.250
2.250

74.28
84.28
94.32

13,050
18,300
24,250

Gear drives are for horizontal output shaft operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Consult factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Add 1.00" to dimensions K, KA, D, W & Y for Size 505ABRJ drive.

Rexnord 2014

(131-110) 91

Type ABRJ Triple and Quadruple Reduction


Hollow Low-Speed Shaft Shrink Disc Mounted
Refer to pages88-91 for basic drive dimensions. Refer to page112 for hollow low-speed shaft and driven shaft recommendations and dimensions.
SHAFT GUARD

SHAFT GUARD

SHRINK DISC

SHRINK DISC

AJ

AJ
AL

AL

UE U

AC

REQUIRED FOR TORQUE


WRENCH CLEARANCE

AC REQUIRED FOR TORQUE


WRENCH CLEARANCE

AG MINIMUM CLEARANCE
REQUIRED FOR REMOVAL
OF SHAFT GUARD

AF
AD

AF

AG MINIMUM CLEARANCE
REQUIRED FOR REMOVAL
OF SHAFT GUARD

AD
SIZES 505-555

SIZES 405-485

Dimensions (in)
Drive
Size

AC

AD

AF

AG

AL

AJ

U
+.002
-.000

UE

405

4.00

26.51

1.20

31.96

16.72

5.2505

5.500

425

4.00

29.91

1.70

37.95

17.96

6.0005

445

5.00

33.33

1.50

42.27

19.83

6.5005

465

5.00

35.60

1.50

45.16

21.33

485

5.00

38.89

1.40

49.94

24.62

505

5.00

42.55

4.17

56.1

535

5.00

45.80

1.12

555

5.50

52.00

2.20

Wt (lb)
Triple

Quadruple

2,310

2,455

6.250

3,280

3,285

6.750

4,575

4,540

7.2505

7.500

6,805

6,860

8.5005

8.750

8,575

9,055

24.33

9.7505

10.000

24.12

12,200

12,950

59.9

25.58

10.5005

10.750

24.12

16,450

18,150

67.0

27.58

11.4005

11.750

26.25

22,650

23,750

Dimensions are for reference only and are subject to change without notice unless certified.
Sizes 405 thru 465, tolerance is +.0016, -.0000; Size 485 thru 555 tolerance is +.0020, -.0000.

92 (131-110)

Rexnord 2014

Type ABX & ABXQ Triple Reduction


Sizes 405-485
Type ABXQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
Y
LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

LA

AE
CLEARANCE

D
SHAFT
COVER

AD

6-HOLES
X DIA. BOLT

J
G

BEARING
GREASE
FITTING

K
W

AE
CLEARANCE

D
S

BA

UE

2.8

2.8
HB

HA

HA

UA

HB

AH
E
HC

HC
V

HD

GREASE
FITTING
(ABXD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

HD

SIZE 405

M
L

SIZES 425-485

Dimensions (in)
Drive
Size

AD

AE

AH

BA

405
425
445
465
485

3.50
4.50
5.00
5.50
7.00

21.34
23.50
25.50
27.23
29.18

30.6
33.5
36.4
39.2
41.9

29.10
32.20
35.60
39.20
43.10

9.70
11.00
12.20
14.00
15.90

4.50
4.00
4.60
4.60
5.40

11.31
12.31
14.62
16.62
18.50

17.65
19.45
21.41
23.16
25.00

1.50
1.50
1.75
1.95
2.29

18.50
21.00
24.00
27.20
26.90

Drive
Size

405
425
445
465
485

Low-Speed Shaft
S

Key

5.000 1.250 x 1.250 x 7.500


5.750 1.500 x 1.500 x 8.000
6.500 1.500 x 1.500 x 10.000
7.250 1.750 x 1.500 x 11.000
8.000 2.000 x 1.500 x 12.000

UA

UB

UC

UD

8.66
10.06
11.38
12.68
14.00

0.750
1.125
1.250
1.250
1.500

1.88
2.25
2.50
2.50
3.00

3.50
3.50
4.00
4.75
5.00

Lubrication System
H

HA

HB

HC

HD

7.47
7.65
9.92
9.92
9.92

12.71
13.19
16.88
18.88
18.88

10.88
10.03
12.09
13.34
15.09

19.99
19.57
21.42
23.20
24.97

1.25
1.35
1.18
1.42
1.87

Keyed Hollow
Low-Speed Shaft
U
UE
+.002
+.000
Keyway
- .000 - .005

5.375
6.000
6.750
7.500
8.500

15.249
15.749
18.499
20.999
23.749

1.000 x 0.312
1.500 x 0.265
1.500 x 0.510
1.500 x 0.510
1.500 x 0.510

9.20
10.25
12.25
14.10
15.60

40.00
45.00
51.50
58.25
58.38

LA

27.75 5.7
31.80 6.6
37.00 6.7
41.00 7.7
46.50 9.4

12.50
14.50
16.75
18.75
21.00

21.62
24.62
29.25
33.25
37.00

37.10
43.71
48.60
54.50
62.60

5.00
6.00
7.00
7.00
8.00

1.50
1.60
1.81
1.79
2.00

High-Speed Shaft
T

Key

1.750
2.250
2.500
2.750
3.500

0.375 x 0.375 x 3.000


0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500
0.625 x 0.625 x 5.000
0.875 x 0.875 x 6.000

Wt (lb)

9.70
10.60
11.70
12.60
13.60

48.41
56.02
63.22
71.12
81.10

1.125
1.250
1.500
1.500
2.000

41.12
46.01
52.67
59.43
59.50

2410
3379
4697
6933
8703

Gear drives are for horizontal floor-mounted operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Dimensions are for reference only and are subject to
change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Dimension shown is for high-speed end of drive. Low speed end of drive is 1.90".
Dimension shown for Size 425 is for high-speed end of drive. Low speed end is 6.7".
Dimension shown for Size 485 is for high-speed end of drive. Low speed end is 9.5".

Rexnord 2014

(131-110) 93

Type ABX & ABXQ Triple Reduction


Sizes 505-555
Type ABXQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

Y
GA

AE
CLEARANCE

D
SHAFT
COVER

AD

EXTERNAL
OIL PUMP
VENTED
DIPSTICK

OIL
FILL
GA

FA

BA

UE

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

FB

BEARING
GREASE
FITTING

KA

K
W
O

A
USABLE
LENGTH

AE
CLEARANCE

D
S

HB

VENTED
DIPSTICK

UA

SEAL
GREASE
FITTING

H.S. SHAFT
KEY

N
HA

SEAL
GREASE
FITTING

OIL FILTER
LIFTING EYES
BOTH ENDS
OF DRIVE

AH

E
HC
T

ALTERNATE
OIL DRAIN
LA

BEARING
GREASE
FITTING
(ABXD ONLY)

INSPECTION
PORT
(BOTH SIDES)

LB

HD

UA
USABLE
LENGTH

Q
M

OIL DRAIN

Dimensions (in)
Drive
Size

AD

AE

AH

BA

GA

505
535
555

7.50
7.50
9.00

33.06
35.18
40.39

47.1
50.8
58.5

47.62
52.00
59.30

17.32
19.50
21.80

6.80
6.80
6.60

19.62
22.62
24.62

27.87
30.00
34.95

27.00
31.75
35.00

10.00

Drive
Size

Low-Speed Shaft
N

Key

UA

UB

Lubrication System
H

HA

HB

HC

HD

9.91
9.91
9.91

16.82
20.00
20.00

16.34
18.84
20.84

27.67
29.68
34.51

2.80
3.05
3.41

Keyed Hollow
Low-Speed Shaft
U
UE
UC UD +.002 +.000
Keyway
- .000 - .005

505 39.25 70.71 10.50 2.25 9.250 2.500 x 1.750 x 14.00 16.18 1.500 3.00 6.00 9.001 24.999
535 45.25 77.80 10.50 2.25 10.500 2.500 x 1.750 x 16.00 18.38 1.500 3.00 7.50 10.501 27.999
555 49.25 87.40 12.00 2.31 11.500 3.000 x 2.000 x 17.00 20.12 1.750 3.50 8.00 11.502 28.999

2.000 x
0.510
2.500 x
0.760
3.000 x
0.760

KA

13.50
16.50
18.00

64.62
74.25
81.75

18.88
21.75
23.75

50.50
56.50
61.50

22.75
25.75
28.25

Wt (lb)

High-Speed Shaft
T

Key

AXV

AXVQ

3.750 0.875 x 0.875 x 6.50 15.16 90.33 2.250 65.83 12,450 12,500
3.750 0.875 x 0.875 x 6.50 16.25 100.42 2.250 75.92 16,500 16,650
4.500 1.000 x 1.000 x 8.50 18.75 112.02 2.250 83.32 23,500 23,050

Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters are held to limits of +.000, -.001. Shaft keyseat depth is one-half of key height.

94 (131-110)

Rexnord 2014

Type ABX & ABXQ Quadruple Reduction


Sizes 405-485
Type ABXQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
Y
LA

UB - DIA. UNC TAP


UC - DEEP
UD - DIA. BOLT CIRCLE

LA

AE
CLEARANCE

D
SHAFT
COVER

AD

6-HOLES FOR
X DIA. BOLT

J
G

BEARING
GREASE
FITTING

AE
CLEARANCE

D
S

2.8

2.8

N
HA

BA

UE

HB
HA

UA

HB

AH
E

HC

HC
V T

GREASE
FITTING
(ABXD ONLY)

INSPECTION
PLUG
(BOTH SIDES)

UA

HD

HD

SIZE 405

L
SIZES 425-485

Dimensions (in)
Drive
Size

AD

AE

AH

BA

405
425
445
465
485

3.00
3.50
3.50
4.50
5.00

21.34
23.50
25.50
27.23
29.18

30.6
33.5
36.4
39.2
41.9

29.10
32.20
35.60
39.20
43.10

9.70
11.00
12.20
14.00
15.90

4.50
4.00
4.60
4.60
5.40

11.31
12.31
14.62
16.62
18.50

Drive
Size

405
425
445
465
485

17.65 1.50
19.45 1.50
21.41 1.75
23.16 1.95
25.00 2.41

Low-Speed Shaft
S

Key

5.000 1.250 x 1.250 x 7.500


5.750 1.500 x 1.500 x 8.000
6.500 1.500 x 1.500 x 10.000
7.250 1.750 x 1.500 x 11.000
8.000 2.000 x 1.500 x 12.000

UA

UB

UC

UD

8.66
10.06
11.38
12.68
14.00

0.750
1.125
1.250
1.250
1.500

1.88
2.25
2.50
2.50
3.00

3.50
3.50
4.00
4.75
5.00

Lubrication System

18.50
21.00
24.00
27.20
30.60

HA

HB

HC

HD

7.47
7.65
9.92
9.92
9.92

12.71
13.19
16.88
18.88
18.88

10.88
10.03
12.09
13.34
15.09

19.99
19.57
21.42
23.20
24.97

1.25
1.35
1.18
1.42
1.87

Keyed Hollow
Low-Speed Shaft
U
UE
+.002
+.000
Keyway
- .000 - .005

5.375
6.000
6.750
7.500
8.500

15.249
15.749
18.499
20.999
23.749

1.000 x 0.312
1.500 x 0.265
1.500 x 0.510
1.500 x 0.510
1.500 x 0.510

9.20
10.25
12.25
14.10
15.60

40.00
45.00
51.50
58.25
56.90

LA

27.75 5.7
31.80 6.6
37.00 6.7
41.00 7.7
46.50 9.4

12.50
14.50
16.75
18.75
21.00

21.62
24.62
29.25
33.25
37.00

39.60
45.80
49.89
58.20
64.60

5.00
6.00
7.00
7.00
8.00

1.50
1.60
1.81
1.79
2.00

High-Speed Shaft
T

Key

1.500
1.750
1.750
2.250
2.500

0.375 x 0.375 x 2.500


0.375 x 0.375 x 3.000
0.375 x 0.375 x 3.000
0.500 x 0.500 x 4.000
0.625 x 0.625 x 4.500

Wt (lb)

9.70
10.60
11.70
12.60
13.60

50.91
58.11
64.51
74.82
83.10

1.125
1.250
1.500
1.500
2.000

41.12
46.01
52.67
59.43
67.04

2558
3383
4664
6990
9184

Gear drives are for horizontal floor-mounted operation with a maximum momentary tilt of 2 unless specifically stated otherwise. Dimensions are for reference only and are subject to
change without notice unless certified.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.
Dimension shown for Size 465 is for high-speed end of drive. Low speed end is 1.90".
Dimension shown for Size 485 is for high-speed end of drive. Low speed end is 2.29".
Dimension shown for Size 425 is for high-speed end of drive. Low speed end is 6.7".
Dimension shown for Size 485 is for high-speed end of drive. Low speed end is 9.5".

Rexnord 2014

(131-110) 95

Type ABX & ABXQ Quadruple Reduction


Sizes 505-555
Type ABXQ Refer to page113 for dimensions of Hollow Low-Speed Shaft with Keeper Plate.
3-HOLES EQUALLY SPACED
UB - DIA. UNC TAP
UC - DEEP
UD - DIA. BOLT CIRCLE

Y
GA

AE
CLEARANCE

D
SHAFT
COVER

SEAL
GREASE
FITTING
EXTERNAL
OIL PUMP

AD

VENTED
DIPSTICK

OIL
FILL
GA

FA

6-HOLES (SIZES 505 & 535)


10-HOLES (SIZE 555) FOR
X DIA. BOLT

FB

BEARING
GREASE
FITTING

BA

UE

KA

K
W
O

A
USABLE
LENGTH

AE
CLEARANCE

D
S

N
HA

HB

VENTED
DIPSTICK

UA
H.S. SHAFT
KEY

SEAL
GREASE
FITTING

OIL FILTER
LIFTING EYES
BOTH ENDS
OF DRIVE

AH

E
HC
T

ALTERNATE
OIL DRAIN
LA

LB

BEARING
GREASE
FITTING
(ABXD ONLY)

INSPECTION
PORT
(BOTH SIDES)

UA
USABLE
LENGTH

HD

Q
M

L.S. SHAFT KEY

OIL DRAIN

Dimensions (in)
Drive
Size

AD

AE

AH

BA

GA

505
535
555

5.50
5.50
7.50

33.06
35.18
40.39

47.1
50.8
58.5

47.62
52.00
59.30

17.32
19.50
21.80

6.80
6.80
6.60

19.62
22.62
24.62

27.87
30.00
34.95

31.00
35.75
40.00

10.00

Drive
Size

Low-Speed Shaft
N

Key

UA

UB

Lubrication System
H

HA

HB

HC

HD

9.91
9.91
9.91

16.82
20.00
20.00

16.34
18.84
20.84

27.67
29.68
34.51

2.80
3.05
3.41

Keyed Hollow
Low-Speed Shaft
U
UE
UC UD +.002 +.000
Keyway
- .000 - .005

505 39.25 72.02 10.50 2.25 9.250 2.500 x 1.750 x 14.00 16.18 1.500 3.00 6.00 9.001 24.999
535 45.25 79.02 10.50 2.25 10.500 2.500 x 1.750 x 16.00 18.38 1.500 3.00 7.50 10.501 27.999
555 49.25 94.21 12.00 2.31 11.500 3.000 x 2.000 x 17.00 20.12 1.750 3.50 8.00 11.502 28.999

2.000 x
0.510
2.500 x
0.760
3.000 x
0.760

KA

13.50
16.50
18.00

72.90
82.25
92.75

18.88
21.75
23.75

50.50
56.50
61.50

22.75
25.75
28.25

Wt (lb)

High-Speed Shaft
T

Key

AXV

AXVQ

2.750 0.625 x 0.625 x 5.00 15.16 91.64 2.250 74.28 13,200 13,250
2.750 0.625 x 0.625 x 5.00 16.25 101.64 2.250 84.28 18,550 18,400
3.750 0.875 x 0.875 x 6.50 18.75 118.83 2.250 94.32 24,600 22,950

Gear drives are for horizontal floor-mounted operation only (output shaft vertical) unless specifically stated otherwise. Consult Factory for other mountings. Dimensions are for
reference only and are subject to change without notice unless certified.
Use ASTM A-354 Grade BC fasteners.
Shaft diameters under 3" are held to limits of +.0000", -.0005". Shaft diameters 3" and over are held to limits of +.000", -.001". Shaft keyseat depth is one-half of key height.

96 (131-110)

Rexnord 2014

Accessories and Additonal Information


Availability & Compatibility of Accessories
Type AR & AXV
Type AR

Electric Fan
High-Speed
End

Electric Fan
Low-Speed
End

Shaft Fan

Cooling
Tubes

Pump &
Cooler

Flange Motor
Adapter

Motor
Mount

Motor
Bracket

Backstop

Torque
Arm

Electric Fan, High-Speed End

Electric Fan, Low-Speed End

OK

OK

OK

OK

OK

Shaft Fan

OK

OK

Cooling Tubes

OK

OK

OK

OK

Pump & Cooler

OK

OK

OK

OK

OK

Flange Motor Adapter

OK

OK

OK

OK

OK

Motor Mount

OK

OK

OK

OK

Motor Bracket

OK

OK

OK

OK

OK

Backstop

OK

OK

OK

OK

OK

OK

OK

OK

Torque Arm

OK

OK

OK

OK

OK

OK

OK

OK

Type AXV

Electric Fan
High-Speed
End

Electric Fan
Low-Speed
End

Cooling
Tubes

Pump &
Cooler

Flange Motor
Adapter

Motor
Mount

Motor
Bracket

Electric Fan, High-Speed End

Electric Fan, Low-Speed End

OK

OK

OK

Cooling Tubes

OK

OK

Pump & Cooler

OK

OK

OK

Flange Motor Adapter

OK

OK

OK

Motor Mount

OK

OK

Motor Bracket

OK

OK

OK

Check usable shaft length and potential interference between fan and motor mount.
Double reduction only.
Will be developed upon receipt of order.
External lubrication pump is mounted in the alternate location, refer to page110.
Cooling tubes not available for Sizes 505, 535 & 555.
All motor accessories for Sizes 505, 535 & 555 will be developed upon receipt of order.

Rexnord 2014

97 (131-110)

Availability & Compatibility of Accessories


Type ABR & ABX
Type ABR

Electric Fan
Low-Speed
End

Shaft Fan

Cooling
Tubes

Pump &
Cooler

Flange Motor
Adapter

Motor
Mount

Motor
Bracket

Backstop

Torque
Arm

Electric Fan, Low-Speed End

OK

OK

OK

OK

OK

Shaft Fan

Cooling Tubes

OK

OK

OK

Pump & Cooler

OK

OK

OK

OK

OK

Flange Motor Adapter

OK

OK

OK

OK

Motor Mount

OK

OK

OK

OK

Motor Bracket

OK

OK

OK

OK

Backstop

OK

OK

OK

OK

OK

OK

Torque Arm

OK

OK

OK

OK

OK

OK

OK

OK

Type ABX

Electric Fan
High-Speed
End

Shaft Fan

Cooling
Tubes

Pump &
Cooler

Flange Motor
Adapter

Motor
Mount

Motor
Bracket

Electric Fan, Low-Speed End

OK

OK

Shaft Fan

Cooling Tubes

OK

Pump & Cooler

OK

OK

OK

Flange Motor Adapter

OK

OK

Motor Mount

OK

OK

Motor Bracket

OK

OK

Will be developed upon receipt of order.


External lubrication pump is mounted in the alternate location, refer to page110.
Cooling tubes not available for Sizes 505, 535 & 555. Sizes 405 & 425 require alternate pump location.
All motor accessories for Sizes 505, 535 & 555 will be developed upon receipt of order.

98 (131-110)

Rexnord 2014

Shaft-Driven Fan Clearance


Type A
Single Reduction Dimensions (in)

AB

Drive
Size

AA

AB

AC

AE

305

2.15

3.44

2.88

10.44

325

2.25

3.75

3.13

11.81

345

2.75

4.62

4.38

12.44

365

3.06

5.31

4.00

14.25

Sizes 385 thru 525A1 are not available with shaft driven fans

CLEARANCE
AA

AC

AE
H.S. SHAFT GUARD

Double Reduction Dimensions (in)


Drive
Size AA

AB

Drive
Size

AC AD AE

AA

AB

AC AD AE

305

1.44 3.44 7.63 1.31 10.00

425

3.50 8.00 9.50

18.06

325

1.81 4.06 9.56 1.12 10.38

445

4.12 8.82 11.42

20.60

345

2.19 4.81 11.38 0.68 11.44

465

5.12 10.60 13.62

23.00

365

2.25 5.25 13.19 0.62 13.25

485

5.82 13.62 17.12 0.76 24.10

385

2.62 6.40 7.06

14.90

505

6.26 14.40 18.50 1.38 27.70

405

2.82 7.06 8.06

16.32

525

7.38 17.50 22.00 1.12 28.25

AB

CLEARANCE

AA

AD

AC

AE
H.S. SHAFT GUARD

Dimensions are for reference only and are subject to change without notice unless
certified.
Where there is no dimension shown, fan does not extend beyond housing.
Sizes 545 thru 585A2 are not available with shaft driven fans.
Triple Reduction Dimensions (in)
Drive
Size

AA

AB

Drive
Size

AC AD AE

AA

AB

AC AD AE

385

2.06 7.12 14.76 0.76 13.68

505

4.18 15.53 32.12

405

1.88 7.76 16.02 1.38 14.65

525

5.00 18.08 37.12 0.50 25.38

425

2.38 8.94 19.02 0.42 15.66

545

5.50 18.25 42.25 0.37 30.71

445

2.68 10.00 21.76 0.98 17.40

565

6.25 19.31 45.60

34.59

465

2.75 11.68 25.08 1.32 18.92

585

6.75 21.04 50.10

37.18

485

3.58 14.58 28.56 0.42 20.62

AB

CLEARANCE

AA

AD

23.60

AC

AE
H.S. SHAFT GUARD

Dimensions are for reference only and are subject to change without notice unless
certified.
Where there is no dimension shown, fan does not extend beyond housing.
Sizes 305 thru 365A3 are not available with shaft driven fans.
Quadruple Reduction Dimensions (in)

AB

Drive
Size

AA

AB

AC

AE

445

2.32

10.88

24.58

16.00

465

2.32

12.68

28.75

16.92

485

2.98

15.41

32.37

19.30

505

3.50

16.74

35.26

21.36

525

3.82

19.00

39.38

23.00

CLEARANCE
AA

AC

AE
H.S. SHAFT GUARD

Dimensions are for reference only and are subject to change without notice unless
certified.
Fan assemblies must be removed from drive to install foundation bolts. Sizes 385
thru 425A4 are not available with shaft fans.

Rexnord 2014

(131-110) 99

Shaft-Driven Fan Clearance


Type AR, ARJ & AXV
Double Reduction Dimensions (in)
Drive
Size

AA

AC

AD

405

2.82

8.06

425

3.50

9.50

445

4.12

11.42

465

5.12

13.62

485

5.82

17.12

0.44

AA
USABLE
LENGTH

AC

Triple Reduction Dimensions (in)


Drive
Size

AA

AC

AD

405

1.88

16.02

0.12

425

2.38

19.02

445

2.68

21.76

0.02

465

2.75

25.08

485

3.58

28.56

0.43

AD

AA
USABLE
LENGTH

AC

Quadruple Reduction Dimensions (in)


Drive
Size

AA

AC

445

2.32

24.58

465

2.32

28.75

485

2.98

32.37

Where dimensions are not shown, fan does not extend beyond housing.
Dimensions are for reference only and are subject to change without notice unless
certified.

100 (131-110)

AA
USABLE
LENGTH

AC

Rexnord 2014

Shaft-Driven Fan Clearance


Type ABR & ABX Triple & Quadruple Reduction
BG
BH

BL

BN
BM

BK

BJ

AA
USABLE
LENGTH

Dimensions (in)
Drive
Size

AA
Triple
Reduction

Quadruple
Reduction

BG

BH

BJ

BK

BL

BM

BN

405

1.88

23.05

11.52

0.63

9.07

9.07

18.14

18.77

425

2.56

1.88

26.05

13.02

0.53

10.07

10.07

20.14

20.67

445

2.76

1.88

30.55

15.27

0.76

10.94

10.94

21.88

22.64

465

2.88

2.56

34.55

17.27

0.40

12.20

12.20

24.40

24.80

485

4.12

2.76

38.30

19.15

0.53

13.07

13.07

26.14

26.67

Dimensions are for reference only and are subject to change without notice unless certified.

Rexnord 2014 (131-110) 101

Electric Fan Clearance


Type A
A
PREFERRED
LOCATION

C
CLEARANCE
0.75
7.24

B
AD

FAN SWITCH

J
CLEARANCE

F
CLEARANCE
0.75

FAN SWITCH

0.75

3.27
0.75

1.73

0.75

K
CLEARANCE

ALTERNATE
LOCATION

G
CLEARANCE

Dimensions (in)
Drive
Size

Reduction

Fan
Diameter

AD

305

1, 2 & 3

12

33.1

26.6

17.62

15.50

8.50

18.12

18.12

15.00

17.5

9.5

325

1, 2 & 3

12

35.3

27.5

17.62

17.63

9.50

18.00

18.00

17.25

17.5

9.5

345

1, 2 & 3

12

37.6

28.6

17.62

20.00

16.62

18.00

18.00

19.62

17.5

9.5

365

1, 2 & 3

14

40.9

30.1

17.62

23.25

12.13

18.00

18.00

22.87

19.1

10.6

16

36.2

28.1

17.43

18.74

10.06

17.99

17.99

18.18

21.5

10.9

2, 3 & 4

14

44.9

28.8

17.60

27.28

10.24

18.52

18.52

26.36

19.5

10.6

18

39.6

30.0

18.14

21.44

11.20

18.78

18.78

20.80

23.0

11.9

2, 3 & 4

14

47.5

29.1

17.49

30.00

11.20

17.89

17.89

29.60

19.5

9.9

385
405
425
445
465

485

505

525

545
565
585

20

42.2

32.9

18.86

23.26

12.74

20.12

20.12

22.00

28.0

14.1

2, 3 & 4

16

53.9

33.9

19.94

33.96

12.74

21.14

21.14

32.76

21.5

10.9

22

50.3

39.3

23.11

27.14

14.50

24.75

24.75

25.50

30.0

14.9

2, 3 & 4

18

57.9

35.4

19.40

38.50

14.50

20.90

20.90

37.00

23.0

11.9

24

55.4

42.4

24.82

30.50

16.50

25.82

25.82

29.50

30.5

15.4

2, 3 & 4

20

63.7

38.7

20.70

43.00

16.50

22.20

22.20

41.50

26.3

14.1

24

61.6

49.6

28.08

33.50

19.00

30.58

30.58

31.00

30.5

15.4

22

62.2

41.2

20.00

42.12

19.00

22.12

22.12

40.00

28.0

14.1

3&4

22

69.7

41.2

20.00

49.62

19.00

22.12

22.12

47.50

28.0

14.1

28

63.9

50.9

27.90

36.00

20.50

30.40

30.40

33.50

34.2

17.3

24

70.7

46.2

23.57

47.12

20.50

25.69

25.69

45.00

30.5

15.4

3&4

24

80.0

46.2

23.57

56.42

20.50

25.69

25.69

54.30

30.5

15.4

28

66.9

52.4

26.90

40.00

22.50

29.90

29.90

37.00

34.2

17.3

24

75.4

50.4

25.52

50.88

22.50

27.90

27.90

48.50

30.5

15.4

3&4

24

85.9

50.4

25.52

60.38

22.50

27.90

27.90

58.00

30.5

15.4

28

86.8

54.8

29.37

57.38

24.50

30.25

31.75

55.00

42.5

24.0

28

95.3

54.8

27.87

67.38

24.50

30.25

30.25

65.00

42.5

24.0

28

89.3

56.8

27.87

61.88

25.50

31.25

30.25

59.50

46.7

21.6

28

104.3

56.8

27.87

76.38

25.50

31.25

30.25

74.00

46.7

21.6

28

96.3

59.3

27.87

68.38

29.00

30.25

30.25

66.00

52.0

21.6

28

109.3

59.3

27.87

71.38

29.00

30.25

30.25

79.00

52.0

21.6

Drawings are representative of this series of drives and may not agree in exact detail for all drive sizes. Dimensions are for reference only and are subject to change without notice
unless certified.

102 (131-110)

Rexnord 2014

Electric Fan Clearance


Type AB All Reductions
B
D

J
CLEARANCE

F
CLEARANCE

0.75

0.75

0.75

0.75

K
CLEARANCE

Dimensions (in)
Drive
Size

385
405
425
445
465

485

505

525

Reduction

Fan
Diameter

AB2

16

28.1

10.06

17.99

21.5

10.9

AB3 & AB4

14

28.8

10.24

18.52

19.5

10.6

AB2

18

30.0

11.20

18.78

23.0

11.9

AB3 & AB4

14

29.1

11.20

17.89

19.5

9.9

AB2

20

32.9

12.74

20.12

28.0

14.1

AB3 & AB4

16

33.9

12.74

21.14

21.5

10.9

AB2

22

39.3

14.50

24.75

30.0

14.9

AB3 & AB4

18

35.4

14.50

20.90

23.0

11.9

AB2

24

42.4

16.50

25.82

30.5

15.4

AB3 & AB4

20

38.7

16.50

22.20

26.3

14.1

AB2

24

49.6

18.50

30.58

30.5

15.4

AB3

22

41.2

18.50

22.12

28.0

14.1

AB4

22

41.2

18.50

22.12

28.0

14.1

AB2

28

50.9

20.00

30.40

34.2

17.3

AB3

24

46.2

20.00

25.69

30.5

15.4

AB4

24

46.2

20.00

25.69

30.5

15.4

AB2

28

52.4

22.50

29.90

34.2

17.3

AB3

24

50.4

22.50

27.90

30.5

15.4

AB4

24

50.4

22.50

27.90

30.5

15.4

Drawings are representative of this series of drives and may not agree in exact detail for all drive sizes. Dimensions are for reference only and are subject to change without notice
unless certified.

Rexnord 2014 (131-110) 103

Electric Fan Clearance


Type AR & AXV
When Type AXV gear drives are furnished with electric fan, the external pump is mounted in the alternate location. Refer to page110.
J
CLEARANCE
0.75

ALTERNATE
LOCATION

0.75

C
CLEARANCE

AD

F
CLEARANCE

0.75

0.75
0.75

K
CLEARANCE

PREFERRED
LOCATION
G
CLEARANCE

Dimensions (in)
Drive
Size

Reduction

Fan
Diameter

AD

405

All

14.0

49.15

30.55

19.34

29.81

11.31

19.24

19.85

29.30

24.55

9.82

425

All

16.0

54.15

32.69

20.45

33.70

12.31

20.38

20.90

33.25

27.55

10.82

445

All

18.0

58.62

35.06

20.57

38.05

14.62

20.44

21.12

37.50

32.05

11.69

465

All

20.0

64.74

38.43

21.93

42.81

16.62

21.81

22.49

42.25

36.05

12.95

485

22.0

65.44

42.78

24.44

41.00

18.50

24.28

24.95

40.49

39.80

13.82

485

3&4

22.0

72.96

42.78

24.42

48.54

18.50

24.48

24.95

48.01

39.80

13.82

Dimensions are for reference only and are subject to change without notice unless certified.

Type ABR & ABX


J
CLEARANCE

B
F
CLEARANCE

0.75

0.75
FAN SWITCH

3.27

0.75
1.73

FAN SWITCH
0.75

7.24

7.24

K
CLEARANCE

Dimensions (in)
Drive
Size

Reduction

Fan
Diameter

405

3&4

14

30.55

11.31

19.24

19.85

10.70

24.55

9.82

425

3&4

16

32.69

12.31

20.38

20.94

11.75

27.55

10.82

445

3&4

18

35.06

14.62

20.44

21.06

14.00

32.05

11.69

465

3&4

20

38.43

16.62

21.81

22.43

16.00

36.05

12.95

485

3&4

22

42.78

18.50

24.28

24.89

17.89

39.80

13.82

Dimensions are for reference only and are subject to change without notice unless certified.

104 (131-110)

Rexnord 2014

Cooling Tube Clearance


Type A

All Drive Sizes and Reductions (Except 385A1, 405A1, 425A1 & 525A1)

Water Inlet and Outlet Connections


(All Drive Sizes and Reductions)

WATER OUT

WATER OUTLET
0.500 - 14 NPT

WATER IN
AJ

HIGHSPEED
END OF
DRIVE

1.25

0.60

AH

AG

AF

WATER INLET
0.500-14 NPT

385
405
425

445

465

485

505

525

545
565
585

AL
AX
CLEARANCE
FOR TUBE
REMOVAL

Provide Clearance for Water Connections Dimensions (in)


Drive
Size

AK

Reduction

AF

AG

AH

AJ

AK

AL

AX

Std
No. of
Tubes

3.00

4.20

6.50

4.20

5.3

6.7

41.0

2&3

2.50

3.76

4.25

1.50

5.8

5.5

48.0

3.00

5.40

6.75

5.40

5.3

6.0

44.0

2&3

3.00

4.05

4.75

1.79

5.8

6.5

54.0

2.50

4.10

7.15

4.10

5.3

6.5

47.0

2&3

2.20

4.75

5.55

1.59

7.3

7.3

61.0

3.20

7.30

7.71

2.78

5.3

5.9

52.0

2&3

2.70

4.90

5.95

1.54

5.3

5.3

63.0

3.30

3.80

5.05

1.54

5.3

5.3

63.0

3.20

7.25

7.68

2.74

5.5

7.3

59.0

2&3

3.00

4.75

7.00

2.50

6.5

6.5

71.0

3.20

4.75

4.95

2.50

6.5

6.5

71.0

3.20

6.56

9.48

4.30

5.8

6.3

62.0

3.50

6.60

8.00

2.08

6.5

6.3

72.0

3.50

6.60

8.00

2.08

5.5

5.8

78.0

3.50

4.30

5.25

2.04

5.5

5.8

78.0

3.70

7.46

9.98

2.94

5.5

5.4

65.0

3.40

8.76

7.90

4.24

6.3

6.0

78.0

3.40

8.76

7.90

4.24

5.5

5.5

86.0

3.70

6.46

5.45

4.20

5.5

5.5

86.0

4.00

8.25

10.35 6.74

5.6

5.6

71.0

4.10

8.25

7.60

3.74

5.5

5.3

82.0

4.10

8.25

7.60

3.74

5.5

5.8

92.0

4.10

5.75

5.85

3.50

5.5

5.8

92.0

3.85

9.81

7.40

2.00

5.9

5.9

87.5

3.85

9.81

7.40

2.00

5.6

5.6

97.5

4.85

10.65

8.40

3.40

5.6

5.6

93.0

4.85

10.65

8.40

3.40

5.6

5.6

107.0

4.85

11.90

8.40

4.10

5.9

5.9

104.0

4.85

11.90

8.40

4.10

5.9

5.9

116.0

All Drive Sizes and Reductions (Except 385A1, 405A1, 425A1 & 525A1)
WATER OUT

WATER IN
AJ

AH
AF

AG

AK

AL
AX
CLEARANCE
FOR TUBE
REMOVAL

Drive Sizes 385A1, 405A1, 425A1 & 525A1


Assemblies: All

WATER IN

WATER OUT

AJ

AH

AG

AF

AK

AL
AX
CLEARANCE
FOR TUBE
REMOVAL

Drawings are representative of this series of drives and do not agree in exact detail
for all drive sizes. Dimensions are for reference only and are subject to change
without notice unless certified. Sizes 305 thru 365, consult Factory.
A minimum flow rate of 2 gallons per minute of clean water is required to prevent tube
fouling. Flow rates in excess of 5 gallons per minute may prompt tube erosion. Thermal
horsepower ratings are based on a water temperature of 70F (21C) with 2 gallons per
minute for Sizes 385 525 and 5 gallons per minute for Sizes 545 585.

Rexnord 2014 (131-110) 105

Cooling Tube Clearance


Type AB

All Drive Sizes and Reductions


Assemblies: 42, 44, 46, 48, 50, 52 & 54

Water Inlet and Outlet Connections


(All Drive Sizes and Reductions)

WATER IN
0.60

WATER OUTLET
0.500 - 14 NPT

AJ

1.25
AK

LOWSPEED
END OF
DRIVE

WATER OUT

AH

AL

AG

AF

AX
CLEARANCE FOR
TUBE REMOVAL

WATER INLET
0.500-14 NPT

All Drive Sizes and Reductions


Assemblies: 41, 43, 45, 47, 49, 51 & 53
Provide Clearance for Water Connections Dimensions (in)
Drive
Size

385
405
425

445

465

485

505

525

AG

AH

AJ

AL

AX

5.8

6.6

41.0

5.4

5.6

48.0

5.6

44.0

Reduction

AF

AB2

1.88

AB3

2.50

3.75

4.25

1.50

AB2

2.00

4.95

5.70

6.1

4.38 4.40

WATER OUT

Std
No. of
Tubes

AK

AB3

3.00

4.05

4.75

1.80

5.5

6.3

53.0

AB2

2.40

2.05

5.45

6.10

6.5

6.3

48.0

AB3

2.20

4.75

5.55

1.60

7.1

7.1

60.0

AB2

2.80

7.50

5.85

0.50

6.8

5.8

63.0

AB3

2.70

4.90

5.95

1.54

5.1

5.1

62.0

AB4

3.30

3.80

5.05

1.54

5.1

5.1

62.0

AB2

2.50

7.60

5.75

1.85

6.5

7.1

60.0

AB3

3.00

4.75

7.00

2.50

6.3

6.3

71.0

AB4

3.20

4.75

4.95

2.50

6.3

6.3

71.0

AB2

3.25

6.75

6.75

2.25

6.4

5.6

62.0

AB3

3.50

6.60

8.00

2.08

6.1

5.9

71.0

AB4

3.50

4.30

5.25

2.04

5.1

5.4

77.0

AB2

3.25

7.46

6.75

2.96

5.9

5.1

65.0

AB3

3.40

8.75

7.90

4.25

5.9

5.6

77.0

AB4

3.70

6.46

5.45

4.20

5.1

5.1

85.0

AB2

3.50

9.00

7.00

2.25

6.2

4.9

71.0

AB3

4.10

8.25

7.60

3.75

4.9

4.7

81.0

AB4

4.10

5.75

5.85

3.50

4.9

5.1

91.0

WATER IN
AJ

AK

AG

AL
AX
CLEARANCE FOR
TUBE REMOVAL

AF

AH

A minimum flow rate of 2 gallons per minute of clean water is required to prevent tube
fouling. Flow rates in excess of 5 gallons per minute may prompt tube erosion. Thermal
horsepower ratings are based on a water temperature of 70F (21C).

Drawings are representative of this series of drives and do not agree in exact detail
for all drive sizes or assemblies. Dimensions are for reference only and are subject
to change without notice unless certified.
Size 385AB2 only, water outlet is on high-speed end of drive.

106 (131-110)

Rexnord 2014

Cooling Tube Clearance


Type AR & ABR
Water Inlet and Outlet Connections
(All Drive Sizes and Reductions)

Assemblies 2, 4 or 6
WATER OUTLET
0.500-14 NPT

WATER OUT
AG

1.25
LOWSPEED
END OF
DRIVE

AJ

0.60
WATER INLET
0.500-14NPT
AY

AK

AL

Provide Clearance for Water Connections

AH

WATER IN

AX
CLEARANCE FOR
TUBE REMOVAL

AF

Assemblies 1, 3 or 5
WATER OUT
AG
AJ

AH

WATER IN

AF

AZ RADIUS

AX
CLEARANCE FOR
TUBE REMOVAL

AL

AK

AY

Dimensions (in)
AH

AJ

AK

AL

AX

AY

AZ

Std
No. of
Tubes

8.08

5.25

6.27

5.7

6.6

50.3

2.1

7.75

10.20

5.24

6.96

7.1

7.2

57.3

3.4

7.75

11.75

5.81

7.94

5.7

8.0

63.1

11.35

5.81

7.94

5.7

8.0

63.1

9.04

13.63

6.22

9.56

5.9

6.1

68.1

6.82

13.03

6.22

9.56

5.9

6.1

68.1

11.53

14.95

6.50

10.29

6.0

5.9

68.0

11.53

14.95

6.50

10.29

6.0

6.4

76.0

9.31

14.36

8.72

10.89

6.0

6.4

76.0

Drive Size

Reduction

AF

405

2&3

7.48

425

2&3

8.69

2&3

8.86

6.59

2&3

445
465

485

AG

Drawings are representative of this series of drives and do not agree in exact detail for all drive sizes. Dimensions are for reference only and are subject to change without notice
unless certified.
A minimum flow rate of 2 gallons per minute of clean water is required to prevent tube fouling. Flow rates in excess of 5 gallons per minute may prompt tube erosion. Thermal horsepower
ratings are based on a water temperature of 70F (21C).

Rexnord 2014 (131-110) 107

Cooling Tube Clearance


Type AXV & ABX
Water Inlet and Outlet Connections
(All Drive Sizes and Reductions)
DRIVE SIZES 405 & 425 AXV2, AXV3 & ABX3
WATER OUT
0.60

WATER OUTLET
0.500 - 14 NPT

LOWSPEED
END OF
DRIVE

AH

1.25

AY

AK

AF

AL

AX
CLEARANCE FOR
TUBE REMOVAL

WATER INLET
0.500-14 NPT

AJ

AG

DRIVE SIZES 445 AXV2, AXV3 & ABX3


WATER OUT

WATER OUT

Provide Clearance for Water Connections

AH

THIS TUBE ON 405 ABX ONLY


(WITH INLET & OUTLET ON L.S. END)

AY

AK

AL

AF

AX
CLEARANCE FOR
TUBE REMOVAL

AJ

AG

DRIVE SIZES 465 & 485 AXV2 AXV3 & ABX3


WATER OUT

WATER IN
SI
AZ ZE 4
RA 05
DI
US

25
E 4 IUS
SIZ RAD
AZ

AF

AK

AL

405 ABX - OPTIONAL LOCATION OF


WATER CONNECTIONS ON H.S. END
WATER IN

WATER OUT

AH

AX
CLEARANCE FOR
TUBE REMOVAL

AJ

AG

DRIVE SIZES 445, 465 & 485 AXV4 & ABX 4

WATER OUT
WATER IN

AH

AH

US
DI
RA
7.4

AF
AG

AK

AF

AL

AX
CLEARANCE FOR
TUBE REMOVAL

AJ

AG

AJ

Dimensions (in)
Drive Size

Red

AF

AG

AH

AJ

AK

AL

AX

AY

AZ

Std
No. of Tubes

405
425

2&3
2&3
2&3
4
2&3
4
2
3
4

5.50
5.33
6.31
6.31
6.54
6.54
7.00
7.00
6.75

8.50
10.20
11.50
11.50
12.99
11.00
13.50
13.50
14.46

7.00
7.73
8.88
8.88
8.95
8.95
9.76
9.76
9.76

7.60
10.20
11.19
9.62
12.99
12.99
15.94
15.94
12.99

5.7
7.1
5.7
5.7
5.9
5.9
6.0
6.0
6.0

6.6
7.2
8.0
8.0
6.1
6.1
5.9
6.4
6.4

50.3
57.3
63.1
63.1
68.1
68.1
68.0
76.0
76.0

2.1
3.4

3.7
8.5

2
4
4
2
4
2
6
6
2

445
465
485

Drawings shown are for Type ABX. Drawings are representative of this series of drives and do not agree in exact detail for all drive sizes or assemblies. Dimensions are for reference
only and are subject to change without notice unless certified.
Sizes 405 & 425 with cooling tubes will use alternate pump location.
A minimum flow rate of 2 gallons per minute of clean water is required to prevent tube fouling. Flow rates in excess of 5 gallons per minute may prompt tube erosion. Thermal horsepower
ratings are based on a water temperature of 70F (21C).

108 (131-110)

Rexnord 2014

600 Series Shaft Mount Cooler


Type A

D MIN
F

D MAX

Dimensions (in)
Drive Size

PA Model

D Min

D Max

385A1

605

29.38

31.91

8.3

24.75

29.61

21.38

9.48

24.75

405A1

605

29.38

32.49

8.88

24.75

29.61

21.38

10.94

24.75

425A1

610

30.51

38.2

10.25

22.75

27.75

21.38

11.26

24.75

610

30.51

39.2

11.25

22.75

26.75

21.38

12.9

24.75

620

30.28

38.79

11.25

26.9

31.88

26.38

12.9

27.25

620

30.28

40.29

12.75

26.9

31.88

26.38

14.5

27.25

630

27.67

44.93

12.75

32.78

37.76

30.38

14.5

28.75

620

30.28

42.29

14.38

26.9

31.88

26.38

13.5

27.25

630

27.67

47.05

14.75

32.78

37.76

30.38

13.5

28.75

445A1
465A1
485A1
505A1
525A1






630

27.67

48.38

16.5

32.78

37.76

30.38

14.5

28.75

640

33.02

62.69

17

46.17

51.15

40.5

14.5

40

630

27.67

49.4

17.13

32.78

37.76

30.38

16.5

28.75

640

33.02

63.35

17.63

46.17

51.15

40.5

16.5

40

Only used with RPM 1750 and higher, and 2.25 ratio and lower.
Only used with RPM 1750 and higher, and 2.76 ratio and lower.
Only used with RPM below 1200.
Only used with RPM above 1200.
Only used with RPM 1750 and higher, and 2.76 ratio and lower.
Only used with RPM below 1200.
Only used with RPM above 1200.

Rexnord 2014 (131-110) 109

Alternate Pump Location


Type AXV & ABX

H
HA

HB
CL OF L.S.S.

HD

HC

Dimensions (in)
Drive
Size

HA

HB

HC

HD

405

19.6

7.70

20.13

21.00

1.24

425

19.8

8.25

18.28

22.79

1.35

445

23.3

10.00

27.30

24.02

2.50

465

25.3

11.81

26.75

25.80

2.75

485

26.0

13.50

26.75

27.40

3.00

Dimensions are for reference only and are subject to change without notice unless certified.
For 485AXV2 and 485ABX3, Dimension H = 27.2.

110 (131-110)

Rexnord 2014

Torque Arm
Type AR, ARJ, ABR & ABRJ

A
(To CL L.S. Shaft)

NON-ADJUSTABLE
TORQUE ARM
J

4-HOLES FOR
M DIA. BOLT
H

B
(To CL of Drive)

G
C

Dimensions (in)
Drive
Size

405
425

45.50

11.00

12.00

5.50

6.00

3.50

4.00

1.25

8.13

1.25

47.50

11.00

12.00

5.50

6.00

3.50

4.00

1.25

8.10

1.25

27.50

62.00

12.00

13.50

6.00

6.75

4.00

4.75

1.50

9.00

1.50

29.50

66.50

12.00

13.50

6.00

6.75

4.00

4.75

1.50

9.00

1.50

33.00

70.00

14.50

15.50

7.25

7.75

5.00

5.50

1.75

9.75

1.75

Standard

Maximum

25.50

22.00

29.00

24.00

445

33.00

465

37.50

485

42.00

Drawings are representative of this series of drives and do not agree in exact detail for all drive sizes or assemblies. Dimensions are for reference only and are subject to
change without notice unless certified. Torque arms for Sizes 505 thru 555 will be developed upon receipt of order.
Dimension shown is for Size 485AR3, AR4 and ABR4; Size 485AR2 and ABR3 Dimension A is 34.60".
Dimension B lengths other than standard are available up to the maximum for an additional charge.
Use Grade 5 fasteners for diameters through 1.50". For larger diameter fasteners, use ASTM A-354 Grade BC.

Rexnord 2014 (131-110) 111

Hollow Low-Speed Shaft Shrink Disc Mounted


Type ARJ & ABRJ

L3

AJ
D

L2

INSTALLATION
A THREADED ROD IS INSERTED THROUGH
THE KEEPER PLATE CENTER HOLE AND INTO
THE TAPPED HOLE IN THE END OF THE DRIVEN
SHAFT. THE THREADED ROD, WITH NUT AS
SHOWN, ARE USED TO AID ASSEMBLY.

L1

INSTALLATION AND REMOVAL CAN BE


ASSISTED THROUGH THE USE OF
ADDITIONAL HARDWARE ITEMS
SHOWN SHADED (CUSTOMER SUPPLIED)

Z - QUANTITY
ZA - DIA. UNC TAPPED HOLES IN HOLLOW SHAFT
ZB - DEEP
Y - DIA. BOLT CIRCLE - EQUALLY SPACED HOLES
FOR KEEPER PLATE RETENTION

ASSEMBLED

REMOVAL
A FASTENER (LARGER DIA THAN THE
THREADED ROD) IS THREADED INTO THE TAPPED
CENTER HOLE OF THE KEEPER PLATE AND IS USED TO
SEPARATE THE DRIVEN SHAFT FROM THE HOLLOW
LOW-SPEED SHAFT OF THE GEAR DRIVE.

Hollow Low-Speed Shaft Dimensions (in)


Drive
Size

AJ
+.0016
-.0000

L1

L2

L3

U
+.002
-.000

ZA

ZB

405
425
445
465
485
505
535
555

5.2505
6.0005
6.5005
7.2505
8.5005
9.7505
10.5005
11.4005

5.400
6.100
6.600
7.400
8.625
9.880
10.600
11.450

2.50
3.50
3.50
3.50
5.00
4.00
4.00
4.50

3.50
5.00
6.00
6.50
8.00
8.20
9.37
9.40

24.70
29.10
31.80
34.10
37.30
43.37
43.24
50.27

5.500
6.250
6.750
7.500
8.750
10.000
10.750
11.750

8
8
6
6
6
6
8
12

0.375-16
0.375-16
0.500-13
0.500-13
0.500-13
0.625-11
0.625-11
0.625-11

0.75
0.75
1.00
1.00
1.00
1.25
1.25
1.25

6.00
6.75
7.50
8.25
9.75
11.25
12.00
12.90

Dimensions are for reference only and are subject to change without notice unless certified.
AJ tolerance for Size 485 is +.0020, -.0000.
GAP (WHEN ASSEMBLED)

S - TAP
T - DEEP
IN END OF
DRIVEN SHAFT

LC

LA

LB

DB

DP

FASTENER AND FLAT WASHER


SUPPLIED BY CUSTOMER

DC

DA

DD

RADIUS

RADIUS

RADIUS

Driven Shaft Recommended Dimensions (in)


Drive
Size

DA
+.0000
-.0015

DB
+.000
-.001

DC
Min

DD
+.010
-.010

Radius
Max

LA

LB

LC

DP

405
425
445
465
485
505
535
555

5.500
6.250
6.750
7.500
8.750
10.000
10.750
11.750

5.250
6.000
6.500
7.250
8.500
9.750
10.500
11.400

6.00
6.75
7.25
8.25
9.50
10.75
11.50
12.50

5.312
6.062
6.531
7.312
8.562
9.800
10.520
11.370

0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125

2.38
3.38
3.38
3.38
4.88
3.88
3.88
4.38

3.75
5.25
6.25
6.75
8.25
8.40
9.60
9.60

24.58
28.98
31.68
33.98
37.18
43.20
43.00
50.00

6.88
7.62
8.62
9.38
10.88
12.75
13.50
14.30

0.75
0.75
1.00
1.00
1.00
1.25
1.25
1.50

1.76
1.76
2.18
2.18
2.18
2.42
2.75
3.00

1.250-7
1.250-7
1.500-6
1.500-6
1.500-6
1.500-6
2.000-4.5
2.000-4.5

2.50
2.50
3.00
3.00
3.00
3.00
4.00
4.00

Hole
Fastener Tapped
in Center of
Length Keeper
Plate

2.50
2.50
3.00
3.00
3.00
3.25
4.00
4.00

1.750-5
1.750-5
2.000-4.5
2.000-4.5
2.000-4.5
2.000-4.5
2.500-4
2.500-4

Gap

0.12
0.12
0.12
0.12
0.12
0.17
0.24
0.27

Dimensions are for reference only and are subject to change without notice unless certified.

112 (131-110)

Rexnord 2014

Hollow Low-Speed Shaft with Keeper Plate


Type AXVQ & ABXQ

STANDARD
ASSEMBLY

GAP

L4

L5

SNAP RING

L3

U
D3

D2

GAP
L6
L7
OPTIONAL
ASSEMBLY

Hollow Low-Speed Shaft Dimensions (in)


Gap Between
Shaft & Plate

Shaft-Diameters

Drive
Size

405
425
445
465
485
505
535
555

U
+.002
-.000

D2
+.010
-.000

D3

5.375
6.000
6.750
7.500
8.500
9.001
10.501
11.501

6.000
6.750
7.750
8.750
9.750
10.500
11.750
13.000

7.00
7.75
9.00
10.00
11.50
12.25
13.50
15.00

L3

L4

L5

L6

L7

13.06
13.20
15.00
15.65
17.30
19.70
21.00
23.40

5.87
6.50
6.90
7.25
7.10
8.10
8.45
9.41

1.875
2.100
2.200
2.500
2.750
3.250
3.250
3.310

23.435
24.800
27.200
28.800
31.250
35.550
37.700
42.690

25.310
26.900
29.400
31.300
34.000
38.800
40.950
46.000

Std
Assy

Opt
Assy

0.14
0.10
0.10
0.10
0.15
0.15
0.20
0.19

2.01
2.20
2.30
2.60
2.90
3.40
3.45
3.50

Dimensions are for reference only and are subject to change without notice unless certified.
Before drive assembly.
GAP
R

LD

KEY

LB

KEYWAY

LA

LC

L (Keyway)
(full radius ends)

H (Keyway)

RADIUS

W (Keyway)

DA
D

D 0.031"

L (Key)

H (Key)

W (Key)

3-HOLES S-UNC TAP,


T-DEEP, EQUALLY
SPACED ON U-DIA.
BOLT CIRCLE

Driven Shaft Recommended Dimensions (in)


Shaft
Drive
DA
Size
+.0000

-.0015

405
425
445
465
485
505
535
555




5.373
5.998
6.748
7.498
8.498
8.999
10.499
11.499

DA
Min

6.500
7.250
8.250
9.250
10.250
11.100
12.350
13.600

Keeper Plate
Radius
.010

LD

0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125

23.300
24.700
27.100
28.700
31.100
35.400
37.500
42.500

LA

5.61
6.24
6.64
6.99
6.84
8.00
8.20
9.30

LB

3.64
4.04
4.34
4.39
3.99
4.80
5.00
6.00

LC

4.64
4.70
5.45
5.90
5.73
3.00
6.00
4.00

P
+.000
-.005

0.870
1.000
1.000
1.250
1.490
1.750
1.750
1.750

1.62
2.13
2.25
2.50
2.99
3.12
3.12
3.28

Keyway

Key

Fastener Length

Snap Ring
(Low-Speed
Shaft
Down Only)

Shaft
Down

Shaft
Up

H
+.010
-.000

600
675
775
875
975
1050
1175
1300

.750-10
1.125-7
1.250-7
1.250-7
1.500-6
1.500-6
1.500-6
1.750-5

3.500
3.500
4.000
4.750
5.000
6.000
7.500
8.000

1.560
2.250
2.500
2.500
3.000
3.000
3.000
3.500

2.25
2.75
3.00
3.25
4.00
4.50
4.50
5.00

4.00
4.75
5.00
5.50
6.50
7.50
7.50
8.00

1.000
1.500
1.500
1.500
1.500
2.000
2.500
3.000

0.453
0.750
0.500
0.500
0.500
1.000
1.000
1.250

16.000
17.500
18.500
19.500
22.500
30.000
26.500
35.000

1.000
1.500
1.500
1.500
1.500
2.000
2.500
3.000

.750
1.000
1.000
1.000
1.000
1.500
1.750
2.000

15.000
16.000
17.000
18.000
21.000
28.000
24.000
32.000

Dimensions are for reference only and are subject to change without notice unless certified.
For Sizes 405-485, TRUARC N5000 Series snap ring; for Sizes 505-555, Spirolox RRN or equivalent.
For Sizes 505-555, hex head fastener with helical spring lock washer.
Sizes 405-425, +.0035", -.0000", Sizes 445-485, +.0040", -.0000".
Full radius keyway ends.

Rexnord 2014 (131-110) 113

Type MCF Couplings Flange Connection


WARNING: Drive system analysis must be performed by Rexnord Application Engineering. Driven shaft loads will be furnished to check shaft stresses and bearing loads. Improper
installation and maintenance of this coupling may result in injury.
P

H
4.50

4.50
GAP

GAP
SHRINK DISC

CL

C
D

DD

DD

CL

B
DRIVING HUB
(Type 2)

DRIVEN HUB
(Type 2)

DRIVING HUB
WITH SHRINK DISC
(Type 4)

DRIVEN HUB
WITH SHRINK DISC
(Type 4)

Dimensions (in)
Drive
Size

405

425

445

Cplg
Size

1045MCF

1055MCF

1060MCF

Hub Type

Hub Type Min/Max Bore

Driving No. Driven No.


Hub

Hub

175SD
175SD
175SD
175SD

200SD
200SD
200SD
200SD

220SD
220SD
220SD
220SD

2
2
2
2
4
4
4
4
2
2
2
2
4
4
4
4
2
2
2
2
4
4
4
4

175SD
185SD
200SD
175SD
185SD
200SD
200SD
220SD
240SD
200SD
220SD
240SD
220SD
240SD
260SD
220SD
240SD
260SD

2
4
4
4
2
4
4
4
2
4
4
4
2
4
4
4
2
4
4
4
2
4
4
4

Driving Hub

Driven Hub

Cplg
Wt (lb)

CL

DD

Gap

3.000-7.000
3.000-7.000
3.000-7.000
3.000-7.000
4.921-5.315
4.921-5.315
4.921-5.315
4.921-5.315
3.500-8.000
3.500-8.000
3.500-8.000
3.500-8.000
5.709-6.102
5.709-6.102
5.709-6.102
5.709-6.102
4.000-9.000
4.000-9.000
4.000-9.000
4.000-9.000
6.299-6.693
6.299-6.693
6.299-6.693
6.299-6.693

3.000-7.000
4.921-5.315
5.315-5.709
5.709-6.102
3.000-7.000
4.921-5.315
5.315-5.709
5.709-6.102
3.500-8.000
5.709-6.102
6.299-6.693
6.693-7.480
3.500-8.000
5.709-6.102
6.299-6.693
6.693-7.480
4.000-9.000
6.299-6.693
6.693-7.480
7.480-8.268
4.000-9.000
6.299-6.693
6.693-7.480
7.480-8.268

510
500
560
570
500
490
540
560
720
710
770
840
710
700
760
840
990
960
1040
1110
960
940
1010
1080

19.68
19.68
19.68
19.68
19.68
19.68
19.68
19.68
21.84
21.84
21.84
21.84
21.84
21.84
21.84
21.84
23.25
23.25
23.25
23.25
23.25
23.25
23.25
23.25

14.12
12.74
13.68
13.68
12.75
11.37
12.31
12.31
16.12
14.68
15.56
16.12
14.69
13.25
14.13
14.69
18.12
16.81
17.31
18.12
16.81
15.50
16.00
16.81

7.00
7.00
7.00
7.00
5.63
5.63
5.63
5.63
8.00
8.00
8.00
8.00
6.57
6.57
6.57
6.57
9.00
9.00
9.00
9.00
7.69
7.69
7.69
7.69

7.00
5.62
6.56
6.56
7.00
5.62
6.56
6.56
8.00
6.56
7.44
8.00
8.00
6.56
7.44
8.00
9.00
7.69
8.19
9.00
9.00
7.69
8.19
9.00

10.00
10.00
10.00
10.00
6.89
6.89
6.89
6.89
11.50
11.50
11.50
11.50
7.87
7.87
7.87
7.87
13.00
13.00
13.00
13.00
13.00
8.66
9.45
10.24

10.00
6.89
7.28
7.87
10.00
6.89
7.28
7.87
11.50
7.87
8.66
9.45
11.50
7.87
8.66
9.45
13.00
8.66
9.45
10.24
13.00
8.66
9.45
10.24

11.82
11.82
11.82
11.82

13.78
13.78
13.78
13.78

14.57
14.57
14.57
14.57

11.82
12.99
13.78

11.82
12.99
13.78

13.78
14.57
15.94

13.78
14.57
15.94

14.57
15.94
16.93

14.57
15.94
16.93

2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
3.00
3.00
3.00
3.00
3.00
3.00
3.00
3.00

7.62
7.62
7.62
7.62
6.25
6.25
6.25
6.25
8.62
8.62
8.62
8.62
7.19
7.19
7.19
7.19
9.62
9.62
9.62
9.62
8.31
8.31
8.31
8.31

6.50
5.12
6.06
6.06
6.50
5.12
6.06
6.06
7.50
6.06
6.94
7.50
7.50
6.06
6.94
7.50
8.50
7.19
7.69
8.50
8.50
7.19
7.69
8.50

0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12

Refer to the Factory all applications above 100 RPM and for drive Sizes 505-585. Dimensions are for reference only and are subject to change without notice unless certified.
Distance required for torque wrench clearance to tighten the shrink disc fasteners. Consult Factory for alternatives if axial space is not available.
All interference fit hubs are bored for a Minimum interference fit of 0.00075 inches per inch of shaft diameter. Driven shaft diameter tolerance is +.000, -.001.
Coupling weights are for hubs with no bore and include shrink disc(s).
Number 2 hub is straight-bored without shrink disc; Number 4 hub is straight-bored with shrink disc.

114 (131-110)

Rexnord 2014

Type MCF Couplings Flange Connection


WARNING: Drive system analysis must be performed by Rexnord Application Engineering. Driven shaft loads will be furnished to check shaft stresses and bearing loads. Improper
installation and maintenance of this coupling may result in injury.
H

H
4.50

4.50

GAP

GAP
SHRINK DISC
C

CL

DD

CL

DD

B
DRIVING HUB
(Type 2)

DRIVEN HUB
WITH SHRINK DISC
(Type 4)

DRIVING HUB
(Type 4)

DRIVEN HUB
(Type 2)

Dimensions (in)
Drive
Size

465

485

Cplg
Size

Hub Type
Driving
Hub

RSB
RSB
RSB
RSB
RSB
1065MCF
240SD
240SD
240SD
240SD
240SD
RSB
RSB
RSB
RSB
1075MCF
208SD
208SD
208SD
208SD

Hub Type Min/Max Bore

No. Driven No.

Hub

2
2
2
2
2
4
4
4
4
4
2
2
2
2
4
4
4
4

RSB
240SD
260SD
280SD
300SD
RSB
240SD
260SD
280SD
300SD
RSB
280SD
300SD
320SD
RSB
280SD
300SD
320SD

2
4
4
4
4
2
4
4
4
4
2
4
4
4
2
4
4
4

Driving Hub

Driven Hub

Cplg
Wt (lb)

CL

DD

Gap

5.000-10.000
5.000-10.000
5.000-10.000
5.000-10.000
5.000-10.000
6.693-7.480
6.693-7.480
6.693-7.480
6.693-7.480
6.693-7.480
6.000-11.500
6.000-11.500
6.000-11.500
6.000-11.500
8.268-9.055
8.268-9.055
8.268-9.055
8.268-9.055

5.000-10.000
6.693-7.480
7.480-8.268
8.268-9.055
9.055-9.646
5.000-10.000
6.693-7.480
7.480-8.268
8.268-9.055
9.055-9.646
6.000-11.500
8.268-9.055
9.055-9.646
9.449-10.236
6.000-11.500
8.268-9.055
9.055-9.646
9.449-10.236

1260
1230
1300
1410
1460
1230
1210
1270
1380
1430
1870
1840
1890
1990
1840
1810
1880
1960

24.50
24.50
24.50
24.50
24.50
24.50
24.50
24.50
24.50
24.50
27.50
27.50
27.50
27.50
27.50
27.50
27.50
27.50

20.12
18.56
19.18
19.65
19.81
19.06
17.00
17.62
18.09
18.25
23.12
21.40
21.56
21.87
21.44
19.72
19.88
20.19

10.00
10.00
10.00
10.00
10.00
8.44
8.44
8.44
8.44
8.44
11.50
11.50
11.50
11.50
9.82
9.82
9.82
9.82

10.00
8.44
9.06
9.53
9.69
10.00
8.44
9.06
9.53
9.69
11.50
9.78
9.94
10.25
11.50
9.78
9.94
10.25

14.00
14.00
14.00
14.00
14.00
9.45
9.45
9.45
9.45
9.45
16.00
16.00
16.00
16.00
11.02
11.02
11.02
11.02

14.00
9.45
10.24
11.02
11.81
14.00
9.45
10.24
11.02
11.81
16.00
11.02
11.81
12.60
16.00
11.02
11.81
12.60

15.94
15.94
15.94
15.94
15.94

18.11
18.11
18.11
18.11

15.94
16.93
18.11
19.09

15.94
16.93
18.11
19.09

18.11
19.09
20.47

18.11
19.09
20.47

3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00

10.62
10.62
10.62
10.62
10.62
9.06
9.06
9.06
9.06
9.06
12.12
12.12
12.12
12.12
10.44
10.44
10.44
10.44

9.50
7.94
8.56
9.03
9.19
9.50
7.94
8.56
9.03
9.19
11.00
9.28
9.44
9.75
11.00
9.28
9.44
9.75

0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12

Refer to the Factory all applications above 100 RPM and for drive Sizes 505-585. Dimensions are for reference only and are subject to change without notice unless certified.
Distance required for torque wrench clearance to tighten the shrink disc fasteners. Consult Factory for alternatives if axial space is not available.
All interference fit hubs are bored for a Minimum interference fit of 0.00075 inches per inch of shaft diameter. Driven shaft diameter tolerance is +.000, -.001.
Coupling weights are for hubs with no bore and include shrink disc(s).
Number 2 hub is straight-bored without shrink disc; Number 4 hub is straight-bored with shrink disc.
Not available on Types AR or ABR.

Rexnord 2014 (131-110) 115

Conversion Factors
U.S. Units to SI Metric Units
(Conversion values listed are for reference only.
DO NOT use these values to convert or compare inch and metric selection guides.)
Description

U.S. Units

Multiply by to Obtain

SI Metric Units

Force

pound force (lbf)


inch (in)
foot (ft)
pound mass (lbm)
horsepower (HP)
pound-inch2 (lb-in2)

4.448
25.4
0.3048
0.4536
0.7457

newton (N)
millimeter (mm)
meter (m)
kilogram (kg)
kilowatt (kW)

0.0002926
1
C = (F - 32)/1.8
0.113
1.356
0.00508
1.609
3.785
0.06308

kilogram-meter2 (kg-m2)
1/min
C
newton-meter (Nm)
newton-meter (Nm)
meters per second (m/s)
kilometers per hour (km/h)
liter (L)
liters per second (L/s)

Length
Mass
Power
Rotational Inertia
Rotational Speed
Temperature
Torque
Velocity
Volume
Volumetric Flow

revolutions per minute (RPM)


F
pound-inch (lb-in)
pound-foot (lb-ft)
feet per minute (ft/min)
miles per hour (mph)
gallon (gal)
gallons per minute (gal/min)

SI Metric Units to U.S. Units


(Conversion values listed are for reference only.
DO NOT use these values to convert or compare inch and metric selection guides.)
Description

SI Metric Units

Multiply by to Obtain

U.S. Units

Force

newton (N)
millimeter (mm)
meter (m)
kilogram (kg)
kilowatt (kW)
kilogram-meter2 (kg-m2 )
1/min
C
newton-meter (Nm)
newton-meter (Nm)
meters per second (m/s)
kilometers per hour (km/h)
liter (L)
liters per second (L/s)

0.2248
0.03937
3.2808
2.2046
1.341
3417.6
1
F = 1.8 (C ) + 32
8.850
0.7376
196.85
0.6124
0.2642
15.85

pound force (lbf)


inch (in)
foot (ft)
pound mass (lbm)
horsepower (HP)
pound-inch2 (lb-in2)
revolutions per minute (RPM)
F
pound-inch (lb-in)
pound-foot (lb-ft)
feet per minute (ft/min)
miles per hour (mph)
gallon (gal)
gallons per minute (gal/min)

Length
Mass
Power
Rotational Inertia
Rotational Speed
Temperature
Torque
Velocity
Volume
Volumetric Flow

Equation:
Torque (Nm) =

9550 x P
n

Torque (lb-in) =

63,000 x HP
n

Where: P = Power (kW); n = shaft speed (RPM)

116 (131-110)

Rexnord 2014

866-REXNORD/866-739-6673 (Within the US)


414-643-2366 (Outside the US)
www.rexnord.com

Why Choose Rexnord?


When it comes to providing highly engineered products that
improve productivity and efficiency for industrial applications
worldwide, Rexnord is the most reliable in the industry.
Commitment to customer satisfaction and superior value
extend across every business function.
Delivering Lowest Total Cost of Ownership
The highest quality products are designed to help
prevent equipment downtime and increase productivity
and dependable operation.

Valuable Expertise
An extensive product offering is accompanied by global sales
specialists, customer service and maintenance support teams,
available anytime.
Solutions to Enhance Ease of Doing Business
Commitment to operational excellence ensures the right
products at the right place at the right time.

Rexnord Company Overview


Rexnord is a growth-oriented, multi-platform industrial company with leading market
shares and highly trusted brands that serve a diverse array of global end markets.
Process and Motion Control
The Rexnord Process & Motion Control platform designs, manufactures, markets
and services specified, highly engineered mechanical components used within complex
systems where our customers reliability requirements and the cost of failure or
downtime are extremely high.
Water Management
The Rexnord Water Management platform designs, procures, manufactures
and markets products that provide and enhance water quality, safety, flow
control and conservation.

2014 Rexnord131-110Printed in USA 09/14

You might also like