You are on page 1of 4

Diyotron.

com-Spot Welder

1 of 4

http://diyotron.com/english/miscellaneous/Spot_Welder.html

Home Page

Alarm Circuits

Audio Circuits

Charging Circuits

Control Circuits

High Voltage

Inverter Circuits

Led Circuits

Metering Circuits

Miscellaneous Circuits

PIC Circuits

Power Supplies

Radio Frequency

Robot Circuits

Spot Welder

Manufacturer of Quality Standard and Special Resistance Welders

This project is a very simple spot welder which will weld thin sheet metal. It will just about weld 0.38mm thick steel. Sheet steel half this
thickness welds effortlessly. It can be used for assembling high vacuum components and making thermocouples.

1/9/2015 9:13 PM

Diyotron.com-Spot Welder

2 of 4

http://diyotron.com/english/miscellaneous/Spot_Welder.html

WARNING: Despite the simplicity of this design, it can be quite hazardous. Goggles must be worn when using it. High temperature is
produced during operation which could cause burns. There is also the hazard of mains voltage internally.
Circuit Description.
Click on the schematic below to see it in higher resolution. This is the basic welder circuit with only the essential components shown. The
relay RL1 is a Crydom D2425 solid state relay. The low voltage dc controlled version has been used so that controlling it with a remote
foot switch (S1) is safe. T2, D1 and C1 provide the control voltage for the solid state relay. There is obviously plenty of scope for variation
and improvement of this design. A worthwhile enhancement would be the addition of a timer to control the duration of the weld.

Construction Details.
T1 uses a transformer removed from a microwave oven. Please be aware that the power supply in a microwave oven is absolutely lethal. Do
not switch the oven on with the cover removed and do not apply power to the transformer until the secondary has been removed. Make
sure that the oven has been unplugged from the supply for at least an hour before removing the cover.
The transformer T1 is the special bit. It is a modified microwave oven transformer. Remove the transformer from an old oven (not the one
from your mothers kitchen). There should be separate windings side by side. Saw off the exposed parts of the secondary windings taking
great care not to damage the primary. Drive out the rest of the secondary wire with a hammer and chisel. Wind about ten turns of insulated
copper wire into the space where the secondary used to be. This wire can be quite thin. It is temporary and will not become the welding
winding. Connect an ac voltmeter to this new secondary. Make the transformer electrically safe by covering all exposed mains wiring and
connect the primary to the mains supply. Switch off and Reduce or increase the number of turns on the secondary to get about 4Vrms.
Unwind the temporary secondary whilst counting the number of turns. Insulate a length of copper braid with shrink sleeve. I used tin plated
copper braid which is 11mm wide and 1.6mm thick. Wind the insulated braid as the new secondary with the correct number of turns to get
4Vrms.

1/9/2015 9:13 PM

Diyotron.com-Spot Welder

3 of 4

http://diyotron.com/english/miscellaneous/Spot_Welder.html

Power/Grounding
Solutions
Pressweld, Bus Bar, Flexible
Shunts Water Cooled Cables,
Ground Straps

I mounted most of the components on a side panel from an old subrack. All exposed metal parts must be earthed.
It would be worth adding an adjustable timer to control weld duration. A timer adjustable from 0.05s to 5s would be of great assistance in
obtaining consistent welds. The welder could also be powered from an external Variac (variable auto transformer) to control the welding
power.
The baseplate fits inside the steel case. The mains enters via an IEC connector on the rear panel. The microwave transformer can be seen on
the right-hand side of the photograph below. The left-hand winding is the primary and the right-hand winding is the copper braid
secondary. The solid state relay is the black box, just to the left of the big transformer. The baby transformer just to the left of the relay is
for the relay control voltage. The primary of this transformer is separately fused at 250mA.

The welding arms are made from mild steel. This may not be ideal; they warm up during use. The bottom one is fixed to the front panel
with a 90 degree bracket. The top one is mounted on a hinge. The hinged electrode arm is insulated from the chassis by a sheet or PTFE. It
can just be seen as a white line between the steel arm and the hinge.
The electrodes are turned from copper. The top one has a 90 degree cone tip. The bottom one has a flat top to make the alignment less
critical. The arms are pulled together by a pair of springs.
The upper arm is connected to the transformer secondary by a short length of copper braid and an M4 bolt which is insulated from the
front panel.
The bottom arm is connected to the other end of the transformer secondary via the bolts which hold the bracket to the front panel. The
bottom arm is also connected to mains earth.
Testing

1/9/2015 9:13 PM

Diyotron.com-Spot Welder

4 of 4

http://diyotron.com/english/miscellaneous/Spot_Welder.html

First power the unit up with a piece of cardboard between the welding electrodes. Connect an ac voltmeter between the electrodes. There
should not be any voltage. Press the weld button or foot-switch. If the circuit is working properly there should be a hum from the
transformer and 4Vrms across the welding electrodes. The voltage should drop back to zero when the switch is released.
Brass cylinders are brazed to the welding arms. These hold the copper electrodes, which are each secured by a screw.
Two pieces of 0.17mm thick stainless steel are held between the electrodes ready for the first test.
Pressing the foot switch give a buzz from the transformer, an orange glow from the tips of the electrodes and a little wisp of smoke.
This is the resulting stainless steel test weld. I have also tried welding tantalum and it works very well. The only problem with welding
tantalum is that it glows white hot. It is so bright that it is painful on the eyes.
Appropriate eye protection should obviously be used when welding materials with very high melting points. Ordinary safety goggles should
be adequate when spot welding steel.

Source of the page:

http://www.rhunt.f9.co.uk/Electronics/Spot_Welder/Spot_Welder_Page1.htm

Date of construction: 16.12.2013


Last update: 10.04.2013 12:28
Contact information: bilgi@elektronobi.com
www.elektronobi.com

1/9/2015 9:13 PM

You might also like