Professional Documents
Culture Documents
10
Probe 2
Probe 11
Heating sleeve
Ceramic filter
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
Components:
10/23-5.10 EN Rev. 10
Filter characteristics
Connection ports
Filter element
Surface filter
Filter fineness
0.3 m
Retention rate
99.98 %
Probe tube
G 3/4 in. internal thread
Seal integrity
104 hPa l/s
Dead volume
280 ml
Instrument air
Free of dust, water and oil
Pressure
Max. 600 kPa
Filter
Aluminum oxide surface filter
105
14
130
160
65
Coating
Thermoset plastic, resistant up to 180 C
Installation
Flange
DN 65, PN 6, form B to DIN 2573, flange gasket A;
positioning of holes:
45, 90, 135, 180, 225, 270, 315, 360
280
40...65
Mounting
Flange connect or bolt to the probe tube
Weight
Approx. 8.0 kg
10/23-5.10 EN Rev. 10
Catalog No.
23042-4-0730743
23042-5-0730744
23042-4-0730745
23042-5-0730746
23042-4-0730747
23042-5-0730748
23042-4-0730749
23042-5-0730750
10/23-5.10 EN Rev. 10
Data
Power supply
120 V AC or 230 V AC, 50 to 60 Hz
Heater output
200 W, 100 W or 50 W depending on setting (see below)
The heating resistors are factory-set for heat output of 100 W
Temperature of heater (unregulated)
Approx. 120 C to 180 C (measured at ambient temperature
of 20 C, still air)
Ambient temperature
0 to 55 C (still air)
Degree of protection of housing
IP50
Materials
Housing: aluminum alloy, heating surface: brass
Weight
Approx. 1.7 kg
Electrical connections
Terminals via M20 cable gland. The electrical supply
conductor must be heat resistant ( 200 C).
Installation
Two half shells are placed round the FE2 filter unit to be heated
and closed with a wing screw.
Option
Regulated heating with 1 x Pt 100
Ordering information
Heating circuit
230 / 115 V AC
200 W
10/23-5.10 EN Rev. 10
230 / 115 V AC
100 W
Catalog No.
23029-5-7865312
23029-5-8008813
23029-5-7865316
23029-5-7865317
230 / 115 V AC
50 W
Heating sleeve
Regulated heating sleeve for FE2 filter unit
Heater
Micanite
Holding temperature
Max. 350 C
Temperature control
Max. 200 C (Pt 100)
Power supply
120 V AC or 230 V AC
Power consumption
250 VA
Connection
Terminal box with M16 cable gland,
degree of protection IP54
Supply cable
3 x 1 mm2 with silicone sheath, length 1 m
Ambient temperature
20 to +45 C
Relative humidity
75 % yearly mean; infrequent slight condensation
permissible
Weight
Approx. 1 kg
Essential accessories
Ordering information
Heated sleeve, 230 V, 50/60 Hz, 250 VA
Heated sleeve, 120 V, 50/60 Hz, 250 VA
Isolation for heated sleeve
Catalog No.
23043-5-8018410
23043-5-8018411
23043-5-8018412
Insulating mat
Temperature controller (see page 39)
10/23-5.10 EN Rev. 10
Protective case
Dimensions
Standard version: 450 x 450 x 400 mm (H x W x D)
Basic version: 270 x 203 x 330 mm (H x W x D)
Material
Special steel 1.4301 (SAE 304)
Degree of protection of housing
IP54
Weight
Standard version: approx. 25 kg incl. FE2 filter unit
Basic version: approx. 17 kg incl. FE2 filter unit
Ambient temperature
20 to +45 C
Options
Annular heating element, unregulated (see page 5)
Heating sleeve, regulated (Pt 100), with insulating mat
(see page 6)
Back purging
Pneumatic valves
Type
2/2-way straight-way diaphragm valve
Operating pressure / control pressure
600 kPa (6 bar)
Nominal diameter
DN 12
Connections
G 1/2 in. internal thread,
control air: G 1/8 in. internal thread
Material
Brass
Mode of operation
Closed in normal position
Ambient temperature
0 to +100 C
10/23-5.10 EN Rev. 10
Control valves
Type
3/2-way solenoid valve
Pressure range
600 kPa (6 bar)
Nominal diameter
DN 2.0
Connections
G 1/8 in. internal thread
Material
Brass
Mode of operation
Closed in normal position
Ambient temperature
0 to +100 C
Electrical connections
Standard connector
Power supply
120 V AC or 230 V AC, 50 to 60 Hz
Power consumption
8 VA
Coaxial valves
Type
2/2-way direct acting valve
Operating pressure
064 bar
Nominal diameter
DN 10
Connections
10/12 x 1 mm
Material
Body: brass, valve seat: synthetic resin on metal, seal: NBR
Mode of operation
Closed in normal position
Ambient temperature
10 to +80 C
Power supply, current consumption
230 V AC, 50 to 60 Hz, 0.13 A
80
165
11,5
6,5
450
50 80
M4
19,5
65
210
M4
75
180
155
110
2x M32
3x M25
2x M20
300
170
160
450
90
155
M4
M4
450
80
Compressed air
Purging
Bulkhead fitting 10/12x1 mm
Test gas connection
Bulkhead fitting 4/6x1 mm
Control air
Bulkhead fitting 4/6x1 mm
Electrical connections
550
300
8
155
75
17
10/23-5.10 EN Rev. 10
440
10 15 20 25 30 35
xmin / mm 229 248 268 287 307 324
Probe protective case, basic version: Dimensional drawing and gas connections (dimensions in mm)
1
2
3
4
330
266
270
200
80
130
2x
M20x1.5
58
3x
2x
M20x1.5 M12x1.5
124
10/23-5.10 EN Rev. 10
3 2
10
Diaphragm Valve
Cleaning Filter Surface and Probe Tube
-Y3.2
Junction Box
Protection Box
Heated
Check Valve
-Y5
Filter Unit
Pt100 Connection
Check Valve
Diaphragm Valve
Puls-Instrumentenluft
-Y1.2
Diaphragm Valve
Cleaning Filter
-Y2.2
A:
D:
Sample Outlet
G 1/4" -> 6 mm or 8 mm Tube Fitting
C:
B:
10/23-5.10 EN Rev. 10
10/23-5.10 EN Rev. 10
Filter unit
Protection box
Junction box
Check valve
Pneumatic connections for 2-stage back-purging, standard version with coaxial valves
11
External
Junction Box
Analyzer Cabinet
-X1
1
N
2
PE
3x1,5 mm
-X1
3x2,5 mm
Heating
Sleeve
Filter Unit
Heated
Sample Line
-E1
-E2
J
N
7
PE
3x1,5 mm
9
10
-E3.1
21.10.2005
J
N
-E3.2
11
PE
12
-X1
3x1,5 mm
-B01
set @ 30C
3x1,5 mm
13
N
14
PE
15
-E4
Frost Protection
Heated
Probe Tube
-X1
L
16
N
17
PE
18
19
-E5.2
Heated Check
Valve
-E5.1
20
21
-T01
4x1,5 mm
115 V~
24 V=
1,3 A
-X2
3x1,5 mm
-Y3.1
2
PE
...
-Y1.1
5
PE
...
-Y2.1
...
PE
10
-Y4
11
12
PE
-Y5
-X2
13
A1
A2
-K01
14
15
PE
3x1,5 mm
3...18
x 0,14 mm
-X3
2x0,14 mm
2x0,14 mm
3
4
5
6
7
8
9
2x
0,14 mm
10 11 12 13 14 15 16 17 18
2x
0,14 mm
2x0,14 mm
2x0,14 mm
12
10/23-5.10 EN Rev. 10
External
Junction Box
Analyzer Cabinet
-X1
PE
-E1
-X1
3x1,5mm
5x2,5mm
Heating
Sleeve
Filter Unit
Heated
Sample Line
L1 L2
L3
-E2
PE
3x1,5mm
-E3.1
10
11
-X1
3x1,5mm
-B01
set@30C
13
N
PE
14 15
-E4
Frost Protection
Heated
Probe Tube
3x1,5mm
12
PE
-E3.2
-X1
L
16
18 19
PE
17
230 V~
-T01
4x1,5mm
20
-E5.1 -E5.2
24V=
1,3A
-X2
...
-Y1
PE
...
-Y2
PE
...
-Y5
-X2
A1
A2
-K05
PE
3x1,5mm
-X3
2x0,14mm
2x0,14
mm
2x0,14mm
2x0,14mm
2x0,14
mm
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
2x0,14mm
10/23-5.10 EN Rev. 10
13
2
3
4
5
A
B
Heating
with heating sleeve and insulation (max. 190 C, Pt 100 required)
with ring heater, unregulated
2
3
1
2
3
Back purging unit with test/emergency purge valve (w/o compressed air unit)
without
with back purging, 1-stage and SS connection adapter
with back purging, 2-stage and SS connection adapter
without back purging, with test/emerg. purge valve, unheated, without SS connection adapter
with back purging, 1-st., with test/emerg. purge valve, heated shut-off valve, SS connection adapter
with back purging, 2-st., with test/emerg. purge valve, heated shut-off valve, SS connection adapter
with back purging, 2-st., heated shut-of valve, SS connection adapter
with back purging, 1-stage via Coax valve, SS connection adapter
with back purging, 2-stage via Coax valves, SS connection adapter
w. back purging, 1-st. via Coax valve, with test/emerg. purge valve, heated shut-off-v., SS connection ad.
w. back purging, 2-st. via Coax valves, with test/emerg. purge valve, heated shut-off v., SS connection ad.
with back purging, 2-st. via Coax valves, heated shut-off valve, SS connection adapter
0
1
2
3
5
6
7
A
B
D
E
F
Power supply
230 V, 5060 Hz
120 V, 5060 Hz
120 V, 5060 Hz CSA, with AWG wiring
1
2
3
Approvals
without
GOST
0
1
Gaskets
Standard
for high corrosive gases
1
2
0
1
1
2
14
10/23-5.10 EN Rev. 10
Filter characteristics
Filter element
Surface filter
Installation
Filter fineness
0.3 m
Flange
DN 65, PN 6, form B to DIN 2527;
positioning of holes: 45, 135, 225, 315
Seal integrity
104 hPa l/s
Mounting
Flange connect or bolt to the probe tube
Dead volume
280 ml
Dimensions
50 / 20 x 135 mm
Connection ports
Heater
Test gas
Bulkhead fitting 6 mm (option)
Sample gas
Pipe fitting 6 mm
Type
Self-regulating heater (400 W)
Purge gas
Bulkhead fittings 18 mm (option)
Temperature
180 C (ambient temperature 20 C)
Probe tube
G 3/4 in. internal thread
Temperature alarm
Approx. 150 C
Power supply
120 V AC or 230 V AC, 50 to 60 Hz
Protective case
Dimensions
270 x 203 x 330 mm (H x W x D)
Options
Annular heating element (see page 5)
Heating sleeve (see page 6)
Material
Special steel 1.4301 (SAE 304)
Weight
Approx. 17 kg incl. FE2 filter unit
Seals
FPM
Ambient temperature
20 to +45 C
10/23-5.10 EN Rev. 10
15
16
266
Cleaning
Filter Surface
and Probe Tube,
Bulk Head Union
18 mm
M20x1,5
3x
M20x1,5
2x
M12x1,5
200
Cleaning Filter,
Bulk Head Union
18 mm
Tube, CU
15x1 mm
Tube, SS 316Ti,
6x1 mm
Calibration Gas
Bulk Head Union
6 mm
Tube, CU
15x1 mm
330
58
10/23-5.10 EN Rev. 10
130
270
80
External
Junction Box
Analyser Cabinet
-X1
Power Supply
Heated Aluminium Form Filter Unit,
230 or 115 VAC, 50...60 Hz, 250 W,
required fusing 6 A
2
PE
3x1,5 mm
PE
-E1.2
-E1.1
-E1.4
-E1.3
set @ 140C
-X1
3x2,5 mm
Heated
Sample Line
-E2
4
PE
PE
-X1
2x0,14 mm
5
6
2x0,14 mm
7
8
9
10
11
Temperature Alarm,
Surface heated Aluminium Forms
12
13
2x0,2 mm
10/23-5.10 EN Rev. 10
17
4
5
6
7
Heating
with self regulated heating and temperature alarm (120 / 230 V AC)
with ring heater, unregulated
with heated sleeve (max. 190 C, Pt 100 required)
1
2
3
3
4
5
1
2
3
Power supply
230 V AC, 5060 Hz
120 V AC, 5060 Hz
1
2
1
2
18
10/23-5.10 EN Rev. 10
Probe system H
water cooled 3)
Probe 2
partly heated
Probe 2
heated
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
p. 22
p. 22
p. 22
p. 22
p. 23
p. 23
< 130C
< 180C
< 300C
180450C
180900C
< 1300C
< 1400C
Dust content
< 50 mg/m3
< 1000 mg/m3
< 3 g/m3
> 3 g/m3
40100 g/m3
< 2000 g/m3
Water vapor
< 65 C
dew point
> 65 C
Acidic aerosols (acid dew pt. 130 C)
Pressure
< 2 bar
< 5 bar
Technical data see
Temperature
2)
1)
p. 20
1)
p. 20
1)
p. 20
1)
p. 20
p. 20
1)
p. 21
5 3
Brickwork
5 3
5 3
Flow direction of
process gas
1 Lead-through tube
2 Mounting flange DN 65, PN 6,
form B to DIN 2573
3 Gasket
4 Welded-on rectangular block
5 Sampling probe flange
xmin / mm
10
133
15
138
20
143
25
147
30
151
35
153
Dimensions in mm
10/23-5.10 EN Rev. 10
19
Use
Max. temperature:
450 C
180 C
900 C
300 C
1300 C
Pressure drop
17,2
16
G3/4
L1
Dust content
Max. 3 g/m3 (application recommendation);
max. 40 g/m3 with purge-back device in conjunction with
FE2 / PFE2 filter unit (not for coated probe tube)
16
15
SiC
Installation
G 3/4 in. external thread
Protective Tube
34
Flow rate
L1
23
Temperature
Probe tube version:
SS 1.4571 (SAE 316Ti)
SS 1.4571 (SAE 316Ti) coated
SS 1.4893
SS 1.4571 (SAE 316Ti) Type 40 W
Silicon carbide (max. length 1000 mm)
G3/4
21,4
16,8
Pressure
12,6
G3/4
105
L1
16
Mounting angle
Any; 8 to 90 downwards from the horizontal is recommended. It is imperative to install the silicon carbide probe
tube vertically.
Ordering information
Catalog No. 23036-0
Version
Stainless steel (1.4571), up to 500 C
Stainless steel (1.4571), coated, up to 180 C
Silicon carbide up to 1300 C, max. 1000 mm
Stainless steel (1.4893), up to 900C
Stainless steel (1.4571), up to 300 C, heated (Type 40 W for cement)
1
2
4
5
6
Nominal length
500 mm
1000 mm
1500 mm
2000 mm
2500 mm
3500 mm (only for heated version)
4000 mm (only for heated version)
4500 mm (only for heated version)
1
2
3
4
5
6
7
8
20
10/23-5.10 EN Rev. 10
Heat output
Nominal length 1000 mm: 2 x 200 W
Nominal length 1500 mm: 2 x 300 W
Nominal length 2000 mm: 2 x 400 W
Nominal voltage
120 V AC or 230 V AC, 50 to 60 Hz
Control
Control temperature max. 200 C
Temperature sensor
Pt 100
Ordering information
Temperature
< 200 C
Catalog No.
23041-4-8018392
23041-4-8018393
23041-4-8018394
Length 1000 mm
Length 1500 mm
Length 2000 mm
Flow rate
Max. 250 l/h
Flow velocity
Max. 12 m/s (> 1000 mm max. 7 m/s)
Dust content
Max. 3 g/m3 (application recommendation);
max. 40 g/m3 with purge-back device in conjunction with
FE2 / PFE2 filter unit (see page 3 or page 7)
T90 time
Approx. 0.4 s at 250 l/h
160
21
1000/1500/2000 mm
Heater
120
40 x 2
25 x 1,5
13
Pt100
123456 789
Bridge:
Line 230 V Terminals 3+4
Line 115 V Terminals 2+3/4+5
Length
M20
Wattage
(W)
400
600
800
Weight
(kg)
10
12
Line Sensor
90
Temperature Controller
Connection
10/23-5.10 EN Rev. 10
21
For sampling hot cement flue gas with high dust content for
CO, CO2, NO and SO2 analysis in dry cement production
process (e.g. recuperator furnaces, furnaces with grate
coolers), at rotary kiln inlet and/or after precalcination.
Quality
Drinking water quality with approx. 30 % anti-freeze if
required
Outlet temperature
Min. 50 C (or > dew point of the cement flue gas),
max. 85 C
Pressure
pabs = max. 400 kPa (4 bar)
Pressure
pabs = max. 200 kPa (2 bar)
Temperature
Probe tube length:
3500 mm
3000 mm
2500 mm
2000 mm
1500 mm
Quantity circulated
Approx. 3 m3/h (closed system)
Max. temperature:
1200 C
1250 C
1300 C
1350 C
1400 C
Flow rate
Max. 250 l/h
Ordering information
Dust content
Max. 2000 g/m3 with periodical compressed air cleaning in
conjunction with FE2 filter unit (see page 3)
Length 1500 mm
Length 2000 mm
Length 2500 mm
Length 3000 mm
Length 3500 mm
Length 1500 mm, reinforced protection tube
Length 2000 mm, reinforced protection tube
Length 2500 mm, reinforced protection tube
Length 3000 mm, reinforced protection tube
Length 3500 mm, reinforced protection tube
Type 60 S, length 1500 mm
Type 60 S, length 2000 mm
Type 60 S, length 2500 mm
Type 60 S, length 3000 mm
Type 60 S, length 3500 mm
Type H, length 1500 mm
Type H, length 2000 mm
Type H, length 2500 mm
Type H, length 3000 mm
Type H, length 3500 mm
Mounting
A flanged probe connector (internal diameter 200 mm) should
be installed by the customer. The mounting flange is essential
for installing the probe tube. The connections should be
aligned according to the local situation.
Catalog No.
23038-4-0856831
23038-4-0856832
23038-4-0856833
23038-4-0856834
23038-4-0856835
23038-4-8018478
23038-4-8018479
23038-4-8018480
23038-4-8018481
23038-4-8018482
23038-4-0730642
23038-4-0730643
23038-4-0730644
23038-4-0730645
23038-4-0730646
23020-4-0730656
23020-4-0730647
23020-4-0730648
23020-4-0730649
23020-4-0730650
60,3
~70
35
89
90
L2
L3
L1
22
10/23-5.10 EN Rev. 10
Probe 2
Use
Nominal voltage
230 V AC, 50 to 60 Hz (120 V AC on inquiry)
Pressure
pabs = max. 400 kPa (4 bar)
Electrical connection
Silicone cable, 3 x 1.5 mm2, length 1000 mm
Temperature
Max. 450 C (probe tube partly heated),
max. 130 C (probe tube heated
Flow rate
Max. 2000 l/h
Dimensions
270 x 203 x 330 mm (H x W x D)
Dust content
Max. 20 g/m3 (application recommendation),
max. 100 g/m3 with purging
Material
Special steel 1.4301 (SAE 304)
Purging pressure
Max. 600 kPa (6 bar)
Heating temperature of inlet filter
200 C (at process gas temperature of 20 C)
90% time (T90)
< 2 s at 250 l/h
Filter fineness
0.3 m
Seals
Ceramic fiber
650
Flange
Special steel 1.4581
1
2
3
4
5
Mounting
Flange
DN 65, PN 6, form B, to DIN 2573
position of holes: 45, 135, 225, 315
Mounting angle
Any; 10 to 35 downwards from the horizontal recommended (take direction of flow into account), see dim. drawing
Sample gas outlet
G 1/4 in. internal thread
Test gas / purge air inlet
G 3/8 in. internal thread
10/23-5.10 EN Rev. 10
180
Ordering information
Catalog No.
1200 mm, 230 V, 50/60 Hz, 650 W
23022-4-0768301
1200 mm, 230 V, 50/60 Hz, 255 W, part. heat.23022-4-0768305
Prot. box, insulat., IP54, (330x203x270 mm) 23022-4-0730719
23
Probe 11
Use
Technical data
Sampling pressure
Atmospheric pressure
Gas temperature
25 to +50 C, dry
Sample gas flow rate
Max. 70 l/h
Dust content
Max. 1 mg/m3
Pressure drop with new filter
10 hPa (mbar) at 70 l/h
Service life of filter (estimated)
filter constant (2500)
d (days) =
flow rate (l/h) x dust concentration (mg/m3)
Ordering information
Catalog No.
23021-4-0859585
Materials
Polycarbonate (probe head), aluminum oxide (filter)
Transport and storage temperature
25 to +70 C
Mounting
On wall or suspended from ceiling
24
10/23-5.10 EN Rev. 10
Ceramic filter
Use
For filtering dust from gases in the gas conditioning systems of
analyzer systems when the gas sampling probe does not have
a filter. The ceramic filter is positioned upstream the other
devices in the sample gas conditioning chain. The ceramic filter
can be heated with the annular heating element if condensation
from the sample gas is likely.
Technical data
Flow rate (air)
Max. 300 l/h
Gas pressure
pabs = 20 kPa to 1.7 MPa (0.2 to 17 bar) at 20 C filter
temperature, max. 200 kPa (2 bar) at 180 C
Pressure drop
0.1 to 0.85 hPa at 30 to 250 l/h (air)
Dynamic characteristics at
Flow rate (air)
30 l/h
3.7 s
Dead time Tt
11.5 s
90% time T90
60 l/h
2.3 s
5.5 s
90 l/h
1.7 s
3.9 s
Filter fineness
0.3 m
Construction, mounting
Materials of gas-conducting parts
Housing: steel, St 37 K or special steel 1.4571 (SAE 316Ti);
filter: aluminum oxide; seals: FPM, Cu, Al2O3 fiber
Ordering information
Ceramic filter, steel version
Ceramic filter, stainless steel version
10/23-5.10 EN Rev. 10
Catalog No.
23031-5-8018177
23031-5-8018178
25
Technical data
Casing: brass
Casing: brass
Single-stage without
manometer
Max. 3.5 MPa (35 bar)
10 to 70 kPa
(0.1 to 0.7 bar)
80 kPa
(0.8 bar)
25 to 250 l/h
Special steel
EPDM
Special steel
Approx. 2.35 kg
Max. 50 C
Approx. 2.35 kg
Max. 50 C
23422-4-0730699
23422-4-0730700
Weight
Gas temperature and
ambient temperature
Approx. 1.25 kg
Max. 50 C
Catalog No.
23035-5-5864958
23035-5-5864951
Construction
Inlet pressure
Outlet pressure
(adjustable)
Safety valve set to
Manometer display
inlet pressure
Manometer display
outlet pressure
Flow rate
Material diaphragm
Material gasket
Material housing
0 to 250 hPa
(0 to 250 mbar)
25 to 250 l/h
Buna rubber
Buna rubber
Brass
26
10/23-5.10 EN Rev. 10
appro
79
NPTF
ble)
(varia
NPTF
x. 30
105
GasTech
approx. 94
(depending on handwheel position)
118
NPTF
appro
148
NPTF
ble)
(varia
NPTF
x. 30
GasTech
approx. 94
(depending on handwheel position)
10/23-5.10 EN Rev. 10
27
Competitive version
Pipe ends with polyamide hard caps
CGWB 13
TBL 01-S
TBL 01-C
TBL 01-E
x
x
x
Polyvinyl chloride (PVC)
Polyamide (PA)
x
x
Metal or PVC
Polyamide (PA)
Various options
Heater and Pt 100 fixed
130 m
x 1) / 2)
x
Various options
Heater and Pt 100 fixed
100 m
x
x
Various options
Heater and Pt 100 fixed
70 m
x
PTFE
Heater and Pt 100 fixed
40 m
see page 33
Anti-frost heater
see page 30
see page 33
28
10/23-5.10 EN Rev. 10
Silicone cap
Metal cap
Hard cap
10/23-5.10 EN Rev. 10
29
PVC
PTFE
Various options (see ordering
information, page 32)
Heater
self-regulating strip heater
Power supply
230 V or 120 V, 50 to 60 Hz
Heat output
16 W/m
Making / holding current
Current consumption
= 65 / 25 mA
Holding temperature
see diagram
Ambient temperature
30 to +60 C
Outer diameter
30 mm
Flexible sample gas pipe
6 x 4 x 1 mm or 8 x 6 x 1 mm
Maximum line length
130 m
Line duct
M42
Minimum bending radius
300 mm
Weight
Approx. 1 kg/m
Connect. lead for heater (fixed) 3 x 2.5 mm2; length 5 m
Connect. lead for Pt 100 (fixed)
PVC
PTFE
Various options (see ordering
information, page 32)
self-regulating strip heater
230 V or 120 V, 50 to 60 Hz
30 W/m
0.15 A/m
PVC
PTFE
Various options (see ordering
information, page 32)
CPD heating element, regulated
230 V or 120 V, 50 to 60 Hz
60 W/m
0.3 A/m
see diagram
30 to +60 C
43 mm
6 x 4 x 1 mm or 8 x 6 x 1 mm
90 m
M42
300 mm
Approx. 1 kg/m
3 x 2.5 mm2; length 5 m
200 C
30 to +60 C
40 mm
6 x 4 x 1 mm or 8 x 6 x 1 mm
60 m
M42
300 mm
Approx. 1 kg/m
3 x 2.5 mm2; length 5 m
LIYCI 2 x 0.14 mm2; length 5 m
- 30
- 20
- 10
+ 10
+ 20
+ 30
+ 40
Ambient temperature C
- 30
- 20
- 10
+ 10
+ 20
+ 30
+ 40
Ambient temperature C
30
10/23-5.10 EN Rev. 10
54
46
63
300
25
POM cap
Shrinking hose
POM cap
Shrinking hose
Pt100
Cable 2 x 0.14 mm
Power Supply
Cable 3 x 1.5...2.5 mm
300
Analyzer side
Power Supply
Cable 3 x 1.5...2.5 mm
300
Analyzer side
49
42
42
10/23-5.10 EN Rev. 10
46
46
31
2
3
7
2
3
4
5
6
1
2
Power supply
230 V, 50 to 60 Hz
120 V, 50 to 60 Hz
1
2
0
1
32
10/23-5.10 EN Rev. 10
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
Technical data
TBL 01-S Self-regulating strip heater
Outer covering
Medium-carrying pipe
Test gas pipe (unheated, option)
Integral pipe end connectors
Power supply
Heat output
Holding temperature
Ambient temperature
Outer diameter
Maximum line length
Line duct
Minimum bending radius
Weight
Electrical connection for
heater and Pt 100 (fixed)
Outer covering
Medium-carrying pipe
Integral pipe end connectors
Power supply
Heat output
Holding temperature
Ambient temperature
Outer diameter
Maximum line length
Line duct
Minimum bending radius
Weight
Electrical connection for
heater and Pt 100 (fixed)
10/23-5.10 EN Rev. 10
230 V or 120 V, 50 to 60 Hz
90 W/m
200 C
30 to +60 C
43 mm
40 m
M48
200 mm
Approx. 1 kg/m
3 x 2.5 mm2 or 2 x 0.14 mm2, length 5 m
33
50
50
56
42
6 mm
300
60
25
Power supply
Cable 3 x 1.5...2.5 mm
81
PA corrugated hose
Analyzer side
Power supply
Cable 3 x 1.5...2.5 mm
Hard cap
PA corrugated hose
Pt100
Cable 2 x 0.14 mm
350
Hard cap
81
24
25
300
54
350
42
42
63
34
49
49
Analyzer side
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
10/23-5.10 EN Rev. 10
10/23-5.10 EN Rev. 10
50
300
Hard cap
2 x M16
Cable Gland
Power supply
Cable 3 x 1.5...2.5 mm
PA corrugated hose
Pt100
Cable 2 x 0.14 mm
Power cupply
Cable 3 x 1.5...2.5 mm
42
Hard cap
350
81
54
49
6
300
56
42
6 mm
24
25
TBL 01-S, pipe end connectors with metal caps for ACF
Analyzer side
PA corrugated hose
Pt100
Cable 2 x 0.14 mm
63
50
60
Analyzer side
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
35
42
54
300
63
49
25
81
45
PVC Jacket
300
Pt100
Cable 2 x 0.14 mm
Power Supply
Cable 3 x 1.5...2.5 mm
300
Analyzer side
Pt100
Cable 2 x 0,14 mm
Power supply
Cable 3 x 1,5...2,5 mm
POM cap
Shrinking hose
Silicone cap
Analyzer side
46
Metall
corrugated hose
51
36
46
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
10/23-5.10 EN Rev. 10
42
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
TBL 01-S Ordering information
Catalog No. 23283-0
Version
Fixed resistor heating strip, 90 W/m, holding temperature 200 C (for ACX)
Self-regulated heating strip, 38 W/m, holding temperature 100 C
Fixed resistor heating strip 90 W/m, holding temperature 200 C (for ACF)
Self-regulated heating strip, 38 W/m, holding temperature 100 C (for SCK)
1
2
4
6
1
3
4
5
Material of sheathing
with plastic hose of PA (outside and indoors installation)
Connections
Metal caps w. 6/4 SS connectors on both sides (ACF)
Probe: metal cap analyzer: flange, 6/4 SS connectors on both sides
Plastic hard caps on both sides (tube 300 mm protruding, self-regulated only)
Silicone caps both sidesprobe 6/4 SS conn.analyzer: tube 300 mm protruding (SCK)
PTFE caps with 6/4 SS connectors on both sides (ACF)
PTFE caps with 6/4 SS connectors on both sides for sample gas and PTFE tube for
test gas 500 mm protruding on both sides (ACF)
A
B
C
D
E
F
0
1
2
Power supply
230 V, 50 to 60 Hz, for self-regulated heating strip (for SCK, not for ACF)
120 V, 50 to 60 Hz, for self-regulated heating strip (for SCK, not for ACF)
230 V, 50 to 60 Hz, for fixed resistor heating conductor 90 W/m
120 V, 50 to 60 Hz, for fixed resistor heating conductor 90 W/m
230 V, 50 to 60 Hz, for fixed resistor heating cond. 90 W/m (ACX, ACF, 35 m)
120 V, 50 to 60 Hz, for fixed resistor heating cond. 90 W/m (ACX, ACF, 15 m)
400 V / 230 V, 50 to 60 Hz, for fixed res. heat. cond. 90 W/m (ACX, ACF, 3560 m)
208 V / 120 V, 50 to 60 Hz, for fixed res. heat. cond. 90 W/m (ACX, ACF, 1540 m)
120 V, 50 to 60 Hz, self-regulated heating strip (for SCK with AWG wiring)
1
2
3
4
5
6
7
8
9
10/23-5.10 EN Rev. 10
37
TBL 01-S, TBL 01-C, TBL 01-E Heated sample gas lines
Additional ordering information TBL 01-S
Fixed resistor heating strip 90 W/m, 6x4x1 mm, length m
Fixed resistor heating strip 90 W/m, 8x6x1 mm, length m
Self-regulated heating strip 38 W/m, 6x4x1 mm, length m
Self-regulated heating strip 38 W/m, 6x4x1 mm, length m
Self-regulated heating strip 38 W/m, 8x6x1 mm, length m
Fixed res. heat. strip, PTFE tube 6x4x1 mm incl. add. unheated PFTE tube for test g. 6x4x1 mm (500 mm protruding), l. m
Fixed res. heat. strip, PTFE tube 8x6x1 mm incl. add. unheated PFTE tube for test g. 6x4x1 mm (500 mm protruding), l. m
Fixed res. heat. strip 90W/m, 400V/230V, 5060 Hz, (ACF, line length 3560m) with PTFE tube 8x6x1 mm, length m
Fixed res. heat. strip 90W/m, 208V/120V, 5060 Hz, (ACF, line length 1540m) with PTFE tube 8x6x1 mm, length m
BA No.
301
303
304
307
309
311
313
315
317
2
3
4
Material of sheathing
with metal corrugated tubing for ACK (outdoor and indoor installation)
with PVC sheathing for ACMP, ACX (outdoor and indoor installation)
1
2
Connections
Probe: metal cap, analyzer: silicone cap (mandatory for ACK) + shortening kit
POM plastic caps on both sides (mandatory for ACMP, ACX) + shortening kit
Probe: PTFE caps, analyzer: POM caps (mand. for ACMP, ACX 120C) + shorten. kit
1
2
3
Control / monitoring
with 1 x Pt 100
Power supply
230 V, 50 to 60 Hz
120 V, 50 to 60 Hz
1
2
38
Catalog No.
23284-4-0730695
23284-4-0730696
23284-4-0730697
23284-4-0730698
10/23-5.10 EN Rev. 10
Outputs
2 x relay 3 A, 250 V AC
Power supply
110 to 240 V AC +10/15 %, 48 to 63 Hz
L1
Dimensions
48 x 48 mm, C-rail housing
not used
110...240 VAC
-15/+10%
48...63 Hz
Measurement input
Pt 100
Alarm 1
Temperature
max.
230V
/3A
0/12V
+
Weight
140 g
Binary
Output 1
Connection diagram
Control range
200 to +850 C
81
83
GND
Temperature controller
max.
230V
/3A
Alarm 2
Limiter
Switching relay
242 243
4+
Catalog No.
10/23-5.10 EN Rev. 10
3-
M2A
Ordering information
Temperature controller
parameters not set
parameters set for filter unit
parameters set for sample gas line
parameters set for self-regulating
heater for ACMP, ACX
Switching relay
Logic
Outputs
Binary
Output 2
Load voltage
Urms = 24 to 265 V
23345-5-8328907
23345-5-8328907P
23345-5-8328907L
23345-5-8328907C
1
L
Last
For load current > 2 A
use coupling relay
23345-5-8328731
39
ABB Limited
Process Automation
Oldends Lane
GL10 3TA Stonehouse
Gloucestershire, United Kingdom
Phone: +44 1 453 826661
Fax:
+44 1 453 829671
ABB Ltd.
Process Automation
14 Mathura Road
121003 Faridabad, Haryana, India
Phone: +91 129 2279627
Fax:
+91 129 2279692
ABB Inc.
Process Automation
3700 W Sam Houston Parkway South,
Suite 600, Houston, TX 77042, USA
Phone: +1 713 587 8000
www.abb.com/analytical
Note
We reserve the right to make technical changes or
modify the contents of this document without prior
notice. With regard to purchase orders, the agreed
particulars shall prevail. ABB does not accept any
responsibility whatsoever for potential errors or
possible lack of information in this document.
We reserve all rights in this document and in the
subject matter and illustrations contained therein.
Any reproduction, disclosure to third parties or
utilization of its contents in whole or in parts is
forbidden without prior written consent of ABB.
Copyright 2013 ABB
All rights reserved
Sales
Service
Contact us