Professional Documents
Culture Documents
ER
RG
LA S
W
NE SIZE
Miniair
Sewair-Mini
Maxiair
Sewair-Maxi
Wellair
Sewair-Dual
Comboair
Sewair-Combo
Flomatic Valves
3/8 thru 4.
INLET
3/8
1/2
3/4
OUTLET
PART NO.
3/8
1/2
3/4
6503
6504
INLET
1
2
OUTLET
PART NO.
INLET
OUTLET
PART NO.
INLET
OUTLET
1/2
1/2
6520
6521
6522
1/2
1
2
1/2
1/2
2
6523
6524
6525
3
4
6
3
4
6
1 thru 8
Cast Iron Body, 1 and 2 with Stainless Steel Trim, 3 thru 8
with Bronze Trim and Stainless Steel Float. BUNA-N Seat.
PART NO.
INLET
OUTLET
PART NO.
INLET
OUTLET
PART NO.
INLET
OUTLET
PART NO.
INLET
OUTLET
6540
6541
1
2
1
2
6542
6543
3
4
3
4
6560
6561
1/2
1
1/2
1
6562
6563
2
3
2
3
Controls rate of flow of water into Maxiair, Wellair, or Comboair. Mounts on inlet of air and vacuum
valve to prevent air release value damage from a surge, due to quick closing valve.
3 thru 12
Cast Iron Body with Stainless Steel and Bronze Trim. BUNA-N Seat.
Install on high points of pipeline with flow velocities of 10 feet per second or greater.
Also install on discharge of high volume pumps, and near any quick closing valves.
A-MINIAIR
B- MAXIAIR
C- COMBOAIR
S- SURGE CHECK
A- WELLAIR
A-MINIAIR
B- MAXIAIR
C- COMBOAIR
S- SURGE CHECK
A- WELLAIR
NOTE: Due to particular system requirement a Miniair and Maxiair may be
PART NO.
INLET
OUTLET
6620
6621
6622
6623
6624
2
2
3
4
6
1
2
3
4
6
PART NO.
INLET
OUTLET
6600
6601
2
3
1/2
1/2
PART NO.
INLET
OUTLET
6640
6641
2
2
1
2
PART NO.
INLET
OUTLET
6650
6651
6652
2
2
3
1
2
3
SD5
S = Slope (decimal)
D = Dia. in inches
( )
P = 16,250,000
3. Enter chart with the air discharge rate and use a pressure
differential no greater than 2 PSI. Pick off valve size.
T
D
1/2
PRESSURE DIFFERENTIAL
IN PSI
7.48
5
4
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
PRESSURE DIFFERENTIAL
IN PSI
CFM =
10
16
12
3
2
1
6. Use the larger of the two vales determined for this system.
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
3/8, 1/2,
3/4
0 to 50
1/8
1/16
3/8
5/16
5/16
5/16
2 1/2
5/8
3/8
3/4
1
3/64
1/32
1/32
3/16
5/32
5/16
1/4
1/4
3/16
5/32
1/2
7/16
3/8
5/16
3/4
5/8
5/8
1/2
1/4
7/16
1/2
Once the orifice size has been determined the appropriate valve
should be selected from the table according to orifice size and
operating pressure. Where greater air accumulations are expected
or field conditions dictate, larger valve body sizes should be used.
When operating pressure and discharge capacity dictate the
necessary orifice size as being smaller than the standard, use the
standard orifice.
7/16
Operating
Pressure
1/32
psig
50
1/8
3/8
1.1
200
2.0
150
1/4
.6
100
250
300
1.5
3.4
7/64
1/8
9/64
5/32
6.6
9.5
12.9
16.9
21.3
26.3
17.9
24.4
31.9
3.7
13.8
15.3
22.1
1/4
5/16
68
72
127
105
187
54.6
88
5.5
38.1
98
157
9.9
5.3
9.6
18.4
37.7
4.5
6.1
3/32
11.8
150
250
4.2
2.4
5/64
7.1
3.2
21.4
300
2.4
1.3
12.4
50
200
1/16
8.1
2.5
Operating
Pressure
3/16
psig
100
3/64
26.4
7.3
18.6
30.0
35.8
9.6
24.4
39.2
46.7
12.1
30.8
40.3
49.5
58.9
14.9
37.9
49.5
61.1
73
3/8
7/16
1/2
5/8
3/4
105
152
205
270
422
607
1080
198
287
1147
2038
59
152
244
290
86
220
352
420
117
298
390
480
572
Flomatic Corporation
Telephone: 1-(800)-833-2040
Fax: 1-(800)-314-3155
www.flomatic.com
153
390
510
627
746
237
592
796
980
1167
343
855
1410
1679
610
1520
2506
2985
Flomatic Valves
Rev. 2/14