Professional Documents
Culture Documents
TOOLS
24.01
Pipe
Preparation
Tools
Victaulic World Headquarters P.O. Box 31, Easton, PA 18044-0031 4901 Kesslersville Rd., Easton, PA 18040 1-800-PICK VIC FAX: 610/250-8817 www.victaulic.com
1629 Rev.C
4/00
Printed in U.S.A.
Anatomy of a Groove
The distinguishing feature of the Victaulic grooved
mechanical piping system is, as the name implies, a
groove where the pipe and fitting engage to form a selfrestraining joint. The position, depth and cross-section of
this groove combine with the fitting housing in an optimal
strength-to-weight relationship. The result is a permanent
connection capable of withstanding thrust loads up to the
maximum rated operating pressure.
Pipe Material
Roll Groove
Square-Cut Groove
Carbon steel
Sch. 80, 40
Stainless steel
Sch. 80, 40
Aluminum1
PVC2
Sch. 80, 40
Sch. 80, 40
Copper
K, L, M, DWV
Ductile3
N/A
N/A
Class 53
1 - Aluminum pipe joint ratings are based on: Alloy 6061-T4/6063-T4 Sch. 80 cut
grooved, Sch. 40 cut or roll grooved, Sch. 30 8, 10 and 12" (200, 250 and 300 mm)
cut or roll grooved, Sch. 5, 10 and 20 roll grooved only; or alloy 6061-T6/6063-T6
Sch. 40 and 80 cut groove only, Sch. 30 8, 10 and 12" (200, 250 and 300 mm) cut
groove only, Sch. 5, 10 and 20 grooving not recommended. Roll grooving of T6
pipe is not recommended because in this stage the pipe is harder and may crack
during roll grooving.
2 - PVC to ASTM D1785: Type 1, Grade 1 (PVC 1120); Type 1, Grade 2 (PVC 1220);
Type 2, Grade 1 (PVC 2120); or Type 2, Grade 1 (PVC 2116). PVC must be radius
cut grooved.
3 - Ductile iron: Special Class 53 minimum wall must be radius cut grooved (rigid or
flexible groove) to ANSI/AWWA C-606.
For information on HDPE, FRP, specialty alloys, lined, coated and other types of pipe,
contact Victaulic.
Roll Groove
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 1
ROLL GROOVING
The concept of cold forming (rolling) a groove into pipe was
developed by Victaulic in 1955. Victaulic has developed a
full line of tools that permits roll grooving of standard
weight steel pipe.
Victaulic Vic-Easy roll grooving tools are all designed to
rotate the pipe as an upper roll is impressed into the pipe.
The lower roll, in addition to driving the pipe, is the female
die inside the pipe. The upper roll is the male die. For all
but the VE12, VE26, VE46 and VE226 tools, Victaulic roll
groovers use hydraulic pressure to force the upper roll into
the pipe to form the groove. Groove depth is controlled by
an adjustable stop. The configuration of the rolls provides
the proper "A" (pipe end to edge of groove) and "B" (groove
width) dimensions.
Roll grooving removes no metal; the groove is cold formed
into the pipe wall. Since the groove is cold formed, the
groove configuration has rounded edges which somewhat
reduce the available pipe movement. Standard roll grooved
pipe will provide one-half the expansion/contraction or
deflection of the same size standard cut groove pipe. Roll
grooving is applicable using appropriate roll groove sets for
steel, stainless, aluminum (Type 6061-T4, 6063-T4) and
similar metallic pipe as well as up to Schedule 80 PVC and
copper tubing.
A B
A B
Hydraulic
Force
Upper Roll
Pipe
Pipe
Lower
(Drive)
Roll
Special roll sets must be used for copper and lightwall stainless steel pipe.
Failure to do so may result in personal injury, property damage, joint leakage or separation.
24.01 - 2
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
The VE12 In-Place IPS Groover is designed for manual grooving of Schedule 5 and 10 steel for - 2"
(26,9 - 60,3 mm) and Schedule 40 steel, stainless steel, aluminum and PVC pipe from 1 - 2" (33,7 - 60,3 mm).
Tracking enhanced rolls allow bi-directional grooving. No power is required and roll changes are
eliminated.
Technical Data
Capacity: See chart below.
Power Requirements: None
Weight: 17 lbs. (8 kg)
Tool
Model
VE12
Pipe
Material
Steel #
10
5, 10, 40
Stainless
40 Std. Rolls
Aluminum
40
PVC
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for non-continuous use.
VE26
Groove In-Place
The VE26 In-Place IPS Groover allows you to repair and retrofit existing 2 - 3" (60,3 - 88,9 mm) Schedule 40
steel and stainless steel pipe plus 2 - 6" (60,3 - 168,3 mm) lightwall steel, PVC, and aluminum. Model VE26C
handles copper tubing (CTS) Types K, L, M and DWV plus British, DIN, and Australian Standard copper.
Tracking enhanced rolls allow bi-directional grooving. No power is required and roll changes are eliminated. Model VE26SS handles 2 - 6" (60,3 - 168,3 mm) Schedule 5 and 10 stainless steel.
Technical Data
Capacity: See chart below.
Power Requirements: None
Weight: 22 lbs. (10 kg)
Tool
Model
VE26S
Pipe
Material
PIPE SIZE/SCHEDULE
2
Steel #
5,10,40
Stainless
5, 10
Aluminum
5, 10, 40
PVC Plastic
5, 10, 40
VE26C
Copper
K, L, M & DWV
VE26SS
Stainless
5, 10
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for non-continuous use.
VE46
Groove In-Place
The VE46 In-Place Groover is designed for manually roll grooving 3 - 6" (101,6 - 168,3 mm) Schedule 40
steel, aluminum, stainless steel and PVC pipe, and 4 - 6" (114,3 - 168,3 mm) Schedule 80 PVC pipe. Tracking
enhanced rolls allow bi-directional grooving. No power is required and roll changes are eliminated.
Technical Data
Capacity: See chart below.
Power Requirements: None
Weight: 28 lbs. (13 kg)
Tool
Model
VE46
Pipe
Material
PIPE SIZE/SCHEDULE
3
Steel #
5, 10, 40
Stainless
40 only
Aluminum
PVC
40
40
40, 80
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for non-continuous use.
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 3
VE226
The VE226 Victaulic roll groovers are light, portable, and easily mount to a Victaulic VPD752 or Ridgid^ 300
power drive. Optional alternate bases are available for Ridgid 535, 1224, 1822, and Oster 310 power drives.
Contact Victaulic regarding others.
Trial grooving depth is easily set with feeler gauges supplied with the tool, with the setting locked in with
an allen wrench (supplied). The tool is operated with a standard " (9,5 mm) square ratchet drive (not
included). The roll groover is protected by an integral overload device which guards against undue load
being applied through the ratchet.
The VE226 is available in six models for steel (and other IPS) pipe, including models for copper tubing and
stainless steel. See chart below for individual tool capabilities.
Technical Data
Capacity: See chart below.
Drive Requirements: Fits Victaulic VPD752 or Ridgid 300 power drives. Optional bases for Ridgid 535, 1224,
1822 and Oster 310 available. Contact Victaulic for others.
Weight: 37 lbs. (17 kg )
Shipping Weight. 40 lbs. (18 kg)
24.01-4A
Steel #
1 - 2
42,4 - 73,0
Stainless
Steel
Aluminum
1 - 2
1 - 2
42,4 - 73,0
42,4 - 73,0
2-4
2-4
2-4
PVC
1 - 6
1 - 6
2-6
2-6
60,3 - 114,3 60,3 - 114,3 60,3 - 114,3 60,3 - 168,3 60,3 - 168,3
42,4 - 168,3
2-6
60,3 - 168,3
2-6
VE226MSS
60,3 - 168,3
VE226B
- 1
- 1
- 1
- 1
- 1
- 1
26,9 - 48,3
26,9 - 48,3
26,9 - 48,3
26,9 - 48,3
26,9 - 48,3
26,9 - 48,3
VE226BSS
- 1
26,9 - 48,3
VE226C*
2-6
54,0 - 155,6
VE266FS
The VE266FS Portable Roll Groover easily mounts to the Victaulic VPD752 or Ridgid 300 Power Drive. The
VE266FS is operated using a hand pump. A unique pivot arm design reduces handle effort. Roll changes
are quick and easy, without changing mainshafts. The VE266FS is also equipped with Victaulic Companys
patented enhanced tracking grooving rolls. The tool is supplied complete with 1 -12" roll sets, with 8 - 12"
rolls installed unless otherwise specified (" roll set optional).
Technical Data
Capacity: See chart below.
Power Requirements: VPD752 or Rigid 300 Power Drive
Weight: 240 lbs. (109 kg)
Shipping Weight: 250 lbs. (114 kg)
Production Speed: See chart below.
Optional Accessories: Optional stabilizer available (8 - 12" only)
Tool
Model
PIPE SIZE/SCHEDULE
Pipe
Material
Steel #
Stainless RX
VE266FS
10
12
.188"
Stainless
40 Std. Rolls
Aluminum
40 Std. Rolls
20
PVC Plastic
Copper
40
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for field fabrication.
24.01 - 4
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
VE272FS
The VE272FS is designed to roll groove 2 - 8" (60,3 - 219,1 mm) Schedule 40 steel, stainless steel, PVC and
aluminum pipe as well as 2 - 12" (60,3 - 323,9 mm) Schedule 5, 10 and 20 steel pipe.
Portable for field use, the VE272FS Vic-Easy tool is designed to easily mount on either the Victaulic VPD752
or the Ridgid 300 power drive. The tool has a manual hydraulic system which supplies grooving force to the
rolls. The tool has easy dial settings for groove depth.
Technical Data
Capacity: See chart below.
Power Requirements: Victaulic VPD752 or Ridgid 300 power drive.
Weight: 240 lbs. (109 kg)
Shipping Weight: 355 lbs. (161 kg)
Production Speed: See chart below.
Optional Accessories: Additional rolls are available for drawn copper tubing 2 - 6" (54,0 - 155,6 mm), Schedule
5S, 10S, and 10 Stainless Steel pipe and ES Grooves.
24.01-3A
Tool
Model
VE272FS
PIPE SIZE/SCHEDULE
Pipe
Material
10
12
Steel #
5, 10, 40
.188"
Stainless
Lightwall S.S.
Aluminum
40
PVC Plastic
40
20
40, 80
Copper
40
K, L, M & DWV
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for field fabrication.
VE270FSD
The VE270FSD is designed for field roll grooving of 1 - 8 (33,7 - 219,1 mm) Schedule 40 steel, stainless
steel, and aluminum pipe ("/26,9 mm rolls optionally available), as well as 1 - 12 (33,7 - 323,9 mm) 0.188
(max.) lightwall carbon steel pipe, 1 - 12 (33,7 - 323,9 mm) Schedule 40 PVC pipe, 2 - 6 (73,0 - 168,3 mm)
Schedule 80 PVC pipe.
The VE270FSD is equipped with a unique pivot arm design, making roll changing quick and easy, without
removing shafts. The patented enhanced tracking rolls reduce the possibility of pipe walking off the tool
during grooving. Trial groove diameter is pre-set with the integral stop.
VE270FSD is a completely self-contained unit with an integral motor, safety foot switch and power plug. It
uses a 110 volt, 15 amp power source.
Technical Data
Capacity: See chart below.
Drive requirements: Self contained
Weight: 340 lbs. (154 kg)
Shipping Weight: 410 lbs. (186 kg)
Optional Accessories: Optional rolls are available for " (26,9 mm) carbon steel (Schedules 5, 10, 20, and 40) and
stainless steel (Schedule 40 only), 2 - 8" (54,0 - 206,4 mm) type K, L, M and DWV copper tubing, and 2 - 12"
(60,3 - 323,9 mm) Schedule 5S and 10S stainless steel pipe. An optional 220 volt, 8 amp power source is available,
as is a pipe stabilizer for 8 - 12" (219,1 - 323,9 mm) pipe.
Tool
Model
Pipe
Material
PIPE SIZE/SCHEDULE
Steel #
Stainless
VE270FSD
Lightwall S.S.
10
12
5, 10, 40
20
Aluminum
40
PVC Plastic
40
Copper
40, 80
40, 80
K, L, M & DWV
20
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for field fabrication.
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 5
VE276FSD
The VE276FSD is designed for field roll grooving of 2 - 8" (60,3 - 219,1 mm) Schedule 40 steel, stainless
steel, PVC and aluminum pipe, as well as 2 - 12" (60,3 - 323,9 mm) Schedule 5, 10 and 20 steel pipe, and 2
- 6" (73,0 - 168,3 mm) Schedule 80 PVC pipe.
The VE276FSD is equipped with a unique pivot arm design, making roll changing quick and easy, without
removing shafts. The patented enhanced tracking rolls reduce the possibility of pipe walking off the tool
during grooving. Trial groove diameter is pre-set with the integral stop.
VE276FSD is a completely self-contained unit with an integral motor, safety foot switch and power plug. It
uses a 115 volt, 15 amp power source. The tool comes equipped with standard grooving rolls for 2 - 12"
(60,3 - 323,9 mm) pipe.
Technical Data
Capacity: See chart below.
Drive requirements: Self-contained.
Weight: 335 lbs. (161 kg)
Shipping Weight: 375 lbs (170 kg)
Optional Accessories: Optional rolls are available for 2 - 8" (54,0 - 206,4 mm) type K, L, M and DWV copper tubing
and 2 - 12" (60,3 - 323,9 mm) Schedule 5S and 10S stainless steel pipe. An optional 220 volt, 8 amp power source is
available, as is a pipe stabilizer for 8 - 12" (219,1 - 323,9 mm) pipe.
Tool
Model
PIPE SIZE/SCHEDULE
Pipe
Material
Steel #
5, 10, 40
5, 10, 40
Stainless
VE276FSD
10
5, 10, 40
Lightwall S.S.
12
5, 10, 20
Aluminum
40
PVC Plastic
40
20
40, 80
Copper
40
K, L, M & DWV
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for field fabrication.
VE268
The VE268 is designed for fabrication shop roll grooving of 1 - 8 (33,7 - 219,1 mm) Schedule 40 and Schedule 40 standard wall stainless steel pipe, 1 - 12 (33,7 - 323,9 mm) 0.188 (max.) lightwall carbon steel pipe,
1 - 12 (33,7 - 323,9 mm) Schedule 40 PVC pipe, 2 - 6 (73,0 - 168,3 mm) Schedule 80 PVC pipe, and 1 - 8
(33,7 - 219,1 mm) Schedule 40 aluminum pipe.
The VE268 is equipped with a unique pivot arm design, making roll changing quick and easy, without
removing shafts. The patented enhanced tracking rolls reduce the possibility of pipe walking off the tool
during grooving. Trial groove diameter is pre-set with the integral stop.
The tool is a motorized, semi-automatic, electro-hydraulic tool. Supplied 220 volt/ 3 phase/ 60 hertz.
The tool comes equipped with 8 - 12 (219,1 - 323,9 mm) pipe stabilizer roll to provide for smooth grooving
operation.
Technical Data
Capacity: See chart below.
Drive requirements: Self-contained.
Weight: 735 lbs. (333 kg)
Shipping Weight: 805 lbs. (365 kg)
Optional Accessories: Optional rolls are available for (26,9 mm) carbon steel (Schedules 5, 10, 20, and 40),
2 - 8" (54,0 - 206,4 mm) type K, L, M and DWV copper tubing, and 2 - 8 (60,3 - 219,1 mm) Schedule 5S and 10S
stainless steel pipe. An optional 440 volt/3 phase/60 hertz wiring. Also can be supplied in various voltages in 3
phase/50 hertz for export. Contact Victaulic for details.
Tool
Model
Pipe
Material
PIPE SIZE/SCHEDULE
Steel #
Stainless
VE268
10
5, 10, 40
12
20
Lightwall S.S.
20
Aluminum
40
PVC Plastic
40
Copper
40, 80
40, 80
K, L, M & DWV
20
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for continuous shop fabrication.
24.01 - 6
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
VE274
The VE274 is designed for fabrication shop roll grooving of 2 - 8 ( 60,3 - 219,1 mm) Schedule 40 steel, stainless steel, PVC and aluminum pipe, as well as 2 - 12 (60,3 - 323,9 mm) Schedule 5, 10 and 20 steel pipe, and
2 - 6 (73,0 - 168,3 mm) Schedule 80 PVC pipe.
The VE274 is equipped with a unique pivot arm design, making roll changing quick and easy, without
removing shafts. The patented enhanced tracking rolls reduce the possibility of pipe walking off the tool
during grooving. Trial groove diameter is pre-set with the integral stop.
The tool is a motorized, semi-automatic, hydraulic feed tool. Supplied 220 volt/ 3 phase/ 60 hertz. The tool
comes equipped with 8 - 12 (219,1 - 323,9 mm) pipe stabilizer roll to provide smooth grooving operation.
Technical Data
Capacity: See chart below.
Drive requirements: Self contained
Weight: 735 lbs. (333 kg)
Shipping Weight: 805 lbs. (365 kg)
Optional Accessories: Optional rolls are available for 2 - 8 (54,0 - 206,4 mm) type K, L, M and DWV copper tubing,
and 2 - 12 (60,3 - 323,9 mm) Schedule 5S and 10S stainless steel pipe. An optional 440 volt/3 phase/60 hertz wiring. Also can be supplied in various voltages in 3 phase/50 hertz for export. Contact Victaulic for details.
Tool
Model
VE274
PIPE SIZE/SCHEDULE
Pipe
Material
10
12
Steel #
5, 10, 40
20
Stainless
20
Lightwall S.S.
Aluminum
40
PVC Plastic
40
20
40, 80
Copper
40
K, L, M & DWV
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for continuous shop fabrication.
VE414
The VE414 is designed for fabrication shop roll grooving of 2 - 16 (60,3 - 406,4 mm) Schedule 5, 10, 20 and
standard wall carbon steel pipe, 2 - 16 (60,3 - 406,4 mm) standard wall stainless steel pipe, 2 - 16 (60,3 406,4 mm) Schedule 40, 2 - 6 (73,0 - 168,3 mm) Schedule 80 PVC pipe, and 2 - 12 (60,3 - 323,9 mm) standard wall aluminum pipe.
The VE414 has a unique roll design, making roll changing quick and easy, without removing main shafts.
The patented enhanced tracking rolls reduce the possibility of pipe walking off the tool during grooving.
Trial groove diameter is pre-set with an integral stop.
The tool is a motorized, semi-automatic, hydraulic feed tool. Supplied 220 volt/ 3 phase/ 60 hertz. The tool
comes equipped with 8 - 16 (219,1 - 406,4 mm) pipe stabilizers to provide smooth grooving operation.
Technical Data
Capacity: See chart below.
Drive requirements: Self-contained.
Weight: 735 lbs. (333 kg)
Shipping Weight: 805 lbs. (365 kg)
Optional Accessories: Optional rolls are available for 2 - 16 (60,3 - 406,4 mm) Schedule 5S and 10S stainless steel
pipe, and 2 - 8 (54,0 - 206,4 mm) type K, L, M and DWV copper tubing. An optional 440 volt/3 phase/60 hertz wiring.
Also can be supplied in various voltages in 3 phase/50 hertz for export. Contact Victaulic for details.
Tool
Model
VE414
Pipe
Material
PIPE SIZE/SCHEDULE
2
10
12
14
Steel #
5, 10, 40
Std. Wall
Stainless
Std. Wall
Lightwall S.S.
Aluminum
PVC Plastic
16
40
40
Copper
40, 80
K, L, M & DWV
20
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for continuous shop fabrication.
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 7
VE416FS
The VE416FS tool is available for field roll grooving of 2 - 16" (60,3 - 406,4 mm) standard wall pipe up to
0.375" (9,5 mm). It will accommodate lightwall steel pipe (see chart below), as well as aluminum, stainless*
and PVC plastic pipe. VE416FS is supplied complete with 2 - 16" (60,3 - 406,4 mm) roll sets, with 8 - 12"
(219,1 - 323,9 mm) rolls installed, unless otherwise specified.
It is equipped with a pipe stabilizer for 6 - 16" (168,3 - 406,4 mm) nominal pipe sizes to control pipe sway. A
groove depth adjuster provides precise groove dimensions and allows for easy adjustment for initial groove
diameter.
VE416FS is provided with a mounting stand for field or shop assembly and set-up. The stand and tool must
be mounted to a Victaulic VPD752 or Ridgid 300 38 rpm power drive before grooving.
Technical Data
Capacity: See chart below.
Drive Requirements: VPD752, or Ridgid 300 power drive.
Weight: 240 lbs. (109 kg)
Shipping Weight: 355 lbs. (161 kg)
Optional Accessories: Additional rolls for drawn copper tubing 2 - 6" (54,0 - 155,6 mm), 8" (206,4 mm) copper, 2"
(60,3 mm) Schedule 80 PVC pipe, 2 - 16" (60,3 - 406,4 mm) lightwall stainless steel pipe and 2 - 12" (60,3 - 323,9 mm)
ES.
Production Speed: See chart on page 4.
*See caution on page 4.
Intended for field fabrication.
VE416FSD
The VE416FSD tool is available for field roll grooving of 2 - 16" (60,3 - 406,4 mm) standard wall pipe up to
0.375" (9,5 mm). It will accommodate lightwall steel pipe, as well as aluminum, stainless and PVC plastic
pipe. VE416FSD is supplied complete with 2 - 16" (60,3 - 406,4 mm) roll sets, with 8 - 12" (219,1 - 323,9 mm)
rolls installed, unless otherwise specified.
The tool is equipped with a pipe stabilizer for 6 - 16" (168,3 - 406,4 mm) pipe sizes to control pipe sway. A
groove depth adjuster provides precise groove dimensions and allows for easy adjustment for initial groove
diameter.
VE416FSD tools are completely self-contained units with integral gear motors, safety foot switch and
power cord/plug. VE416FSD uses a 110 volt, 15 amp power source, with a 220 volt, 8 amp model optional
upon request.
Technical Data
Capacity: See chart below.
Power Requirements: 110 volt, 15 amp for integral gear motor (220 volt, 8 amp model available upon request)
Weight: 340 lbs. (154 kg)
Shipping Weight: 550 lbs. (250 kg)
Optional Accessories: Optional rolls are available for drawn copper tubing 2 - 6" (54,0 - 155,6 mm), 8" (206,4 mm)
copper, 2" (60,3 mm) Schedule 80 PVC pipe, 2 - 16" (60,3 - 406,4 mm) lightwall stainless steel pipe and 2 - 12"
(60,3 - 323,9 mm) ES.
*See caution on page 4.
24.01-3A
Tool
Model
Pipe
Material
PIPE SIZE/SCHEDULE
2
Steel #
Stainless
VE416
and
VE416FSD
10
5, 10, 40
12
14
16
Standard Wall
0.375" Std. Rolls Only
Aluminum
Copper
Lightwall S.S.
PVC Plastic
3
5, 10, 40
40
40
40, 80
Standard Wall
40, 80
K, L, M & DWV
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for field fabrication.
24.01 - 8
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
VE424
The Vic-Easy VE424 model is a fully motorized, automated shop tool for continuous production roll grooving of pipe from 4 - 42" (114,3 - 1067,0 mm) and wall thicknesses up to 0.375" (9,5 mm). The tool operates on
220/440 volt three phase power supply. The tool is supplied with 4 - 24" (114,3 - 610,0 mm) standard groove
rolls (unless otherwise specified), instructions and wiring diagrams.
Technical Data
Capacity: See chart below.
Power Requirements: 220 or 440 volt, 3 phase, 60 Hz 30/16 amps
Shipped Set For: Std. groove 8 - 12" (219,1 - 323,9 mm) steel pipe and 220 volt service
Weight: 1,000 lbs. (454 kg)
Shipping Weight: 1,260 lbs. (567 kg)
Optional Accessories: 4 - 24" (127,0 - 610,0 mm) lightwall stainless steel pipe rolls, 4 - 12" (114,3 - 323,9 mm) ES
groove rolls, and conversion kits for grooving 26 - 36" (660,4 - 914,0 mm) and 38 - 42" (965,2 - 1067,0 mm) standard
wall 0.375" (9,5 mm) steel pipe.
Tool
Model
PIPE SIZE/SCHEDULE
Pipe
Material
Steel #
5, 10, 40
Stainless
VE424
10
12
14
16
5, 10, 40
Lightwall S.S.
18
20
22
24
Standard Wall
0.375" Wall Only
Aluminum
40, 80
PVC Plastic
Standard Wall
40, 80
40
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for continuous shop fabrication.
VE436
The VE436 is a fully automated shop tool for roll grooving pipe with a maximum wall thickness of 0.500"
(12,7 mm) (See chart below.) All rolls for 4 - 36" (114,3 - 914,0 mm) are included at no extra charge. Requires
220/440/3/60 power supply (shipped wired for 220 volt unless otherwise specified.)
Technical Data
Capacity: See chart below.
Weight: 1500 lbs. (680 kg)
Tool
Model
Pipe
Material
Steel #
Stainless
VE424
Aluminum
PVC Plastic
10
12
14
40*
18
20
22
24
26
0.500" Wall*
28
30
32
36
0.500" Wall
0.375" Wall
40
0.375" Wall
40, 80
16
40
*For pipe sizes 12 - 24" (323,9 - 610,0 mm), the maximum wall thickness is limited to 0.375" (9,5 mm) wall for pipe lengths shorter than
4' (1.2 m).
#Maximum ratings on steel are limited to pipe of 180 BHN (Brinnell Hardness Number) and less.
Intended for continuous shop fabrication.
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 9
ACCESSORIES
VPD752
The Victaulic VPD752 Power Drive can be used as the power drive unit for the VE226, VE272FS and
VE416FS roll grooving tools, provided the tool is equipped with the correct base plate. It utilizes a 60Hz universal motor and requires 115V/1 Phase 15 amps of power. It is operated with a safety foot switch.
Technical Data:
Capacity: See appropriate tool
Power Requirements: 115 volts, 15 amp, 50/60 Hz (220 volt, 6 amp, 50/60 cycle optional)
Weight: 91 lbs. (41 kg)
Shipping Weight: 192 lbs. (87 kg)
VAPS112
The VAPS112 Adjustable Pipe Stand is designed for supporting pipe to be roll grooved. It is a four legged
portable self-standing unit that permits free pipe rotation and traversing on ball transfers. Turnstile design
allows pipe to be spun around for grooving of both pipe ends without dismounting pipe from stand.
VAPS112 Stand supports pipe sizes 1 - 12" (33,7 - 323,9 mm) up to 1075 pounds (490 kg) in weight.
Technical Data:
Capacity: 1 - 12" (33,7 - 323,9 mm) IPS pipe
Load Rating: 1075 lbs./490 kg
Vertical Stroke: 14" (368 mm) for adjusting rod, 8" (216 mm) leg adjustment, 23" (584 mm)
Minimum Pipe Height from Floor: 23" (584 mm) on 12" (323,9 mm) pipe, 21" (533 mm) on 1" (33,7 mm) pipe
Weight: 154 lbs. (70 kg)
Shipping Weight: 197 lbs. (89 kg)
Handle Effort Required to Raise 1075 lbs. (488 kg) Load: 55 lbs. (25 kg) maximum.
VAPS224
The VAPS224 Adjustable Pipe Stand is designed specifically for supporting pipe to be roll grooved. It is a
self-standing heavy-duty unit that permits free pipe rotation and traversing on ball transfers. Ball transfers
are mounted in a manner permitting use of pipe slings. Turnstile design allows pipe to be spun around for
grooving of both pipe ends without dismounting pipe from stand. VAPS224 Stand supports pipe sizes 2 24" (60,3 - 610,0 mm) up to 1800 pounds (816 kg) in weight.
Technical Data:
Capacity: 2 - 24" (60,3 - 610,0 mm) IPS pipe.
Load Rating: 1800 lbs./816 kg
Vertical Stroke: 23" (584 mm)
Minimum Pipe Height from Floor: 13" (325 mm) on 24" (610,0 mm) IPS pipe
Maximum Pipe Height from Floor: 38" (965 mm) on 2" (60,3 mm) IPS pipe.
Weight: 260 lbs. (118 kg)
Shipping Weight: 307 lbs. (139 kg)
Handle Effort Required to Raise 1800 lbs. (817 kg) Load: 50 lbs. (23 kg) maximum
VAPS3036
The VAPS3036 Victaulic Adjustable Pipe Stand is a portable and self-standing unit that permits free pipe
rotation and traversing on ball transfers. It is designed for direct use with the Vic-Easy roll grooving tools.
Technical Data
Capacities: 26 - 36 IPS (660,4 - 914,0 mm) pipe
Load Rating: 2700 lbs. (1225 kg)
Vertical Stroke: 11 (292 mm)
Min. Pipe Height from Floor: 13 (330 mm) on 36 (914,0 mm) pipe
Weight: 250 lbs. (113 kg)
Shipping Weight: 297 lbs. (135 kg)
Handle Effort Required to raise 1800 lbs. (817 kg) Load: 50 lbs. (23 kg) maximum
24.01 - 10
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
CUT GROOVING
Victaulic developed the grooved piping concept in 1925
and designed the first portable cut grooving tools in 1945.
Technology now provides a variety of tools for cut grooving
from - 24" (26,9 - 610,0 mm) pipe including steel, stainless, aluminum, ductile and cast iron, PVC plastic, bare or
lined pipe.
All Victaulic cut groovers are designed to be driven around
a stationary pipe to machine away material, providing a
groove. The design of the tool assures a groove which is
concentric with the pipe O.D., even with out-of-round pipe.
The groove is always of uniform depth. An integral depth
stop is adjustable to provide proper groove depth. Stops in
the tool provide the proper dimension from the pipe end to
the groove (A dimension). The tool bit provides proper
groove width (B dimension).
C
Standard Cut Groove
(For steel and other IPS pipe)
Depth
Stop
Tool
Bit
Pipe
Stop
B
Pipe
Inner Roll
Vic-Adjustable tools
provide proper groove
dimensions
R
Radius Cut Groove
(For ductile or cast iron pipe)
Standard Steel Pipe
R
Radius Cut Groove
(For PVC plastic pipe)
Above drawings have been exaggerated for clarity
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 11
Technical Data:
Capacity: 2"/2.375" (60,3 mm) - 8"/8.625" (219,1 mm) steel and other metallic IPS pipe; 3"/3.960" (100,6 mm) 6"/6.900" (175,3 mm) ductile/cast (AWWA dimensions)
Drive Requirements: External drive, minimum 1 hp.
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove 4 - 6" (114,3 - 168,3 mm) steel pipe
Weight: 37 lbs. (17 kg)
Tool
Model
VG28GD
Adjustable
Groover
Pipe
Material
40, 80
Stainless
40, 80
Aluminum
Steel
40, 80
Ductile Iron
Class 53
Vic-Adjustable
VG26GD (MRL)
A special variation of the VG26GD tool is available to groove and machine for rubber lining (MRL) in one
operation.
Technical Data:
Capacity: 2 - 6" (60,3 - 168,3 mm) steel (and other IPS pipe)
Weight: 37 lbs. (17 kg)
Shipping Weight: 54 lbs. (25 kg)
Intended for continuous shop fabrication.
Vic-Groover
Individual Tools
Vic-Groover tools are designed for manual or power cut grooving of a single size steel, stainless steel, aluminum and PVC pipe, ranging from - 8" (26,9 - 219,1 mm). Tools are supplied with a ratchet handle for
manual operation. Tools 2" (60,3 mm) and larger are supplied with a power yoke. The VG46 model will
groove 4 - 6" (114,3 - 168,3 mm) IPS pipe and Vic-Groover tools are available for 3, 4, 6 and 8" (100,6, 121,9,
175,3 and 229,9 mm) cast pipe plain and cement lined.
Vic-Groover tools are available for 3, 4 and 6" (100,6, 121,9 and 175,3 mm) for BS 4772/ISO ductile iron pipe.
Technical Data:
Drive Requirements: Manual or external drive, min. hp. (0.37 kw)
Drive Speed: 40 rpm max.
Shipped Set For: Standard groove, IPS of size indicated or rigid/flexible for ductile/cast pipe.
Tool
Model
Vic-Groover
Individually
Sized
- 8"
Vic-Groover
Adjustable
4, 5, 6"
Pipe
Material
PIPE SIZE/SCHEDULE
1 1
Steel
40, 80
Stainless
40, 80
Aluminum
40, 80
PVC
40, 80
Steel
40, 80
Stainless
40, 80
Aluminum
40, 80
Vic-Groover
3" D.I. Pipe
Ductile Iron
Vic-Groover
4" D.I. Pipe
Ductile Iron
Vic-Groover
6" D.I. Pipe
Ductile Iron
Vic-Groover
8" D.I. Pipe
Ductile Iron
Class 53
Class 53
Class 53
Class 53
24.01 - 12
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
The VG824 is designed for cut grooving various metallic pipe materials in sizes ranging from nominal
8 - 24" (219,1 - 610,0 mm) and wall thickness from 0.238" (6 mm) - 0.750" (19 mm), depending upon size.
The tool must be driven through its own integral gear box by an external power source at a maximum
speed of 38 rpm. The VG824 is ideal for job site, fab shop or production cut grooving. Tool includes one 8 24" (219,1 - 610,0 mm) standard tool bit and one extra.
Vic-Adjustable
VG824
Technical Data:
Capacity: IPS 8"/8.625" (219,1 mm); 0.238" (6 mm) wall - 24" (610,0 mm); 0.750" (19 mm) wall; Cast 8" 9.050"
(230 mm); 0.360" (9 mm) wall - 24" (25.800"/655 mm); 0.750" (19 mm) wall
Drive Requirements: External drive, min. 1 hp.
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove, 8 - 12" (219,1 - 323,9 mm) steel pipe
Weight: 82 lbs. (37,2 kg)
Shipping Weight: 126 lbs. (57,2 kg)
Options: 8" std. tool bit0.437" (11 mm); 22 - 24" std. tool bit 0.563" (14 mm) and tool bits for 8 - 24"
(229,9 - 655,3 mm) cast/ductile pipe.
Tool
Model
Pipe
Material
PIPE SIZE/SCHEDULE
8
10
Steel
VG824
Adjustable Groover
12
14
16
18
20
40, 80
Stainless
30, 40
Aluminum
22
24
30, 40
30, 40
Ductile Iron
Class 53
A special variation of the VG824 is available to groove and machine for rubber lining (MRL) in one operation.
Vic-Adjustable
VG824 MRL
Technical Data:
Capacity: IPS 8" (8.625/219,1 mm); 0.238" (6 mm) wall - 24" (610,0 mm); 0.750" (19 mm) wall
Drive Requirements: External drive, min. 1 hp.
Drive Speed: 38 rpm max.
Shipped Set For: Standard groove, 8 - 12" (219,1 - 323,9 mm) steel pipe
Weight: 82 lbs. (37,2 kg)
Shipping Weight: 126 lbs. (57,2 kg)
Intended for continuous shop fabrication.
VG412 Orbital
Machining Tool
VG412 is a complete modular pipe end preparation system. Quick, accurate cutting and grooving for 4 - 12"
(122,0 - 335,0 mm) ductile iron pipe to meet AWWA and other industry specifications for mechanical couplings. The external mounting and drive action is particularly suited to cement lined ductile iron pipe
grooving. Rugged and reliable, VG412 allows you to cut and groove with one set-up. VG412 is supplied
with a 120 volt/11.5 amp power drive. Hinged frame design allows cutting at any point along the pipeline.
Blade setting and replacement is fast and easy. The tool can be used for 4 - 12" (114,3 - 323,9 mm) carbon
steel (lined) with the addition of an IPS steel kit.
The VG412 is also available for grooving British Standard/ISO ductile iron pipe of BS 4772/ISO dimensions
for 88,9, 114,3 and 168,3 mm (3, 4 and 6) sizes.
Technical Data:
Capacity: Cast 4" (4.80") - 12" (13.20") and 4 - 12" (114,3 - 323,9 mm) IPS steel (with optional IPS steel kit)*
Drive Requirements: 120 volt/11.5 amp
Shipped Set For: Rigid Radius Groove, 4 - 12" (122,0 - 335,0 mm) ductile iron pipe
Weight: 151 lbs. (69 kg)
Shipping Weight: 285 lbs. (129 kg)
Options: 4 - 12" (114,3 - 323,9 mm) IPS steel kit
PIPE SIZE/SCHEDULE
Tool
Model
Pipe
Material
VG412
Adjustable Groover
Ductile Iron
Class 53
Steel
40, 80*
10
12
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 13
Vic Plastic
Groovers
ACCESSORIES
Power Mule
Power Mule is the ideal drive for Victaulic individual Vic-Groover Tools, VG28GD and VG824. It is a heavyduty, two-wheeled unit which drives Victaulic cut grooving tools at the speed and power necessary for
accurate grooving.
Power Mule is equipped with a Forward-Off-Reverse control, integral foot switch, and a 1" square drive
connection. Tool plugs directly into 115 volt, 15 amp service.
Technical Data:
Capacity: Victaulic Individual Vic-Groover Tools, Victaulic VG28GD, VG26GD/MRL, Victaulic VG824, VG824/
MRL.
Power Requirements: 115 volts, 15 amp 50/60 Cycle
Full Load Speed: 35 rpm
Weight: 190 lbs./86 kg
Intended for continuous shop fabrication.
Speed Reduction
Control (LSCR)
Speed Reduction Control (LSCR) is designed for electrical speed reduction on various universal power drives used
in conjunction with Victaulic cut grooving tools (individual Vic-Groover Tools, VG28GD & VG824).
LSCR is recommended for Universal Power Drives that operate at speeds in excess of Victaulic Cut Groover
specifications which incorporate Universal motors. LSCR is used in series between a 115 volt, 15 amp
supply and the power drive. Not for use with induction-type motors.
Technical Data:
Capacity: Universal Motor-type Power Drives (Example: Ridgid 300 portable pipe threader) rated at 115 volt,
15 amp maximum
Power Requirements: 115 volts, 15 amp 50/60 Cycle
Weight: 3 lbs. (1,4 kg)
Shipping Weight: 5 lbs. (2,3 kg)
Intended for continuous shop fabrication.
24.01 - 14
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
Pocket-sized steel tapes are available for taking circumferential measurements, marked in ths of an
inch increments. Tapes may be used for measuring - 22" (26,9 - 559,0 mm) pipe O.D. at the base of the
groove (the C diameter). Tapes are notched on the lead end to allow proper overlap within the groove for
more accurate measurement.
Pipe Diameter
Tape
R
JA1224 Joint
Alignment Tool
The JA1224 Joint Alignment Tool is designed for aligning pipe and fittings for the installation of large diameter Victaulic products. The tool can be used on IPS and AWWA pipe, sizes 12 - 24" (323,9 - 610,0 mm), with
an additional unit capable of handling sizes 36 - 48" (914,0 - 1219,2 mm).
The joint alignment tool is made of durable ductile iron for rugged use in the field.
Technical Data
Capacity: 12 - 24" (323,9 - 610,0 mm) IPS and AWWA pipe
Weight: 60 lbs. (27 kg)
JA2448 Joint
Alignment Tool
The JA2448 Victaulic Joint Alignment Tool is designed to assist in aligning pipe/fitting ends for installation
of Victaulic 24 - 48" (610,0 - 1219,2 mm) IPS/AWWA couplings. The JA2448 tool is able to align pipe-to-pipe,
pipe-to-fitting and fitting-to-fitting arrangements.
Technical Data
Capacity: 24 - 48" (610,0 - 1219,2 mm) IPS and AWWA pipe
Weight: 85 lbs. (39 kg)
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 15
PRESSFIT TOOLS
The Pressfit System requires a Pressfit Tool specifically designed and sized for securing Pressfit products onto pipe. A Pressfit Tool equipped
with the proper sized press jaws must be used for Pressfit product assembly.
The Pressfit Tool package includes the actual pressing tool and complete operating instructions. The jaws, designed specifically for each size
pipe (, , 1, 1, 1 and 2" /21,3, 26,9, 33,7, 42,4, 48,3 and 60,3 mm), can be leased or purchased separately in sizes needed along with the tool.
Jaws are changed quickly by sliding the locking pin and removing. Jaws fit both the electric and electrohydraulic tools. The correct size jaws
must be used for the corresponding pipe size.
PFT505
Pressfit Electric
U
L
ULC
Victaulic Pressfit System products are designed for use only with UL/ULC Listed and FM Approved Schedule 5 steel pipe or Victaulic Schedule 5 stainless steel pipe. Victaulic stainless steel pipe carries the label
Victaulic Pressfit Pipe Certified For Use With Pressfit Products, or Vic-Press 304 stainless steel pipe.
The Pressfit System requires a Pressfit tool designed for securing Pressfit products onto pipe. The tool must
be equipped with the proper sized Victaulic press jaws that correspond with the size of the pipe and the
Pressfit products being used (see accessories). The Pressfit tool package includes the actual pressing tool
and any customer specified press jaws. Jaws are available separately for rental or purchase in , , 1, 1,
1 and 2" sizes. The PFT505 Pressfit tool is designed for industrial and trade use only.
The Pressfit tool is supplied in a steel carrying case with a Pressfit System Product Assembly and Tool
Operation Manual.
The Pressfit tool is electrically powered and hydraulically driven and requires a 110v/60 cycle/6.5 amp -AC
current supply.
FM
Technical Data:
Capacity: - 2" (21,3 - 60,3 mm) IPS Schedule 5 steel and stainless steel pipe.
Power Requirements: 110v/60 cycle/6.5 amp
Shipping Weight: 42 lbs. (19 kg)
Accessories: , , 1, 1, 1, and 2" (21,3 - 60,3 mm) jaws available for rental or sales separately
Intended for field fabrication..
PFT501
Pressfit Hydraulic
Victaulic Pressfit System products are designed for use only with UL/ULC Listed and FM Approved Schedule 5 steel pipe or Victaulic Schedule 5 stainless steel pipe. Victaulic stainless steel pipe carries the label
Victaulic Pressfit Pipe Certified For Use With Pressfit Products, or Vic-Press 304 stainless steel pipe.
The Pressfit System requires a Pressfit tool designed for securing Pressfit products onto pipe. The tool must
be equipped with the proper size Victaulic press jaws that correspond with the size of the pipe and the
Pressfit products being used. (see accessories.) The Pressfit tool package includes the actual pressing tool
and any customer specified press jaws. Jaws are available separately for rental or purchase in , , 1, 1,
1 and 2" sizes. The PFT501 Pressfit tool is designed for industrial and trade use only.
Technical Data:
Capacity: - 2" (21,3 - 60,3 mm) IPS Schedule 5 steel and stainless steel pipe.
Power Requirements: 110v/60 cycle 8.0 amps
Shipping Weight: 120 lbs. (54 kg) (with full set of jaws)
Accessories: , , 1, 1, 1, and 2" (21,3 - 60,3 mm) jaws available for rental or sales separately
Intended for field fabrication.
PFT507
Pressfit Pneumatic
The Pressfit System requires a Pressfit tool designed for securing Pressfit products onto pipe. The tool must
be equipped with the proper sized Victaulic press jaws that correspond with the size of the pipe and the
Pressfit products being used. The Pressfit tool packages include the actual pressing tool and any customer
specified press jaws. Jaws are available separately for rental or purchase in , , 1, 1, 1 and 2" sizes.
The PFT507 Pressfit tool is designed for industrial and trade use only and is not approved for sprinkler system installations.
The Pressfit tool is supplied in a steel carrying case with a Pressfit System Product Assembly and Tool
Operation Manual.
The Pressfit tool is pneumatically powered and hydraulically driven.
Technical Data
Capacity: - 2 (21,3 - 60,3 mm) IPS Schedule 5 steel and Vic-Press 304 and 316 stainless steel pipe.
Power Requirements: Compressed Air(75 - 90 psi)
Shipping Weight: 42 lbs. (19 kg)
Accessories: , , 1, 1, 1 and 2 (21,3 - 60,3 mm) jaws available for rental or sale separately.
Intended for field fabrication.
24.01 - 16
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
HCT908
Hole Cutting Tool
The HCT 908 Hole Cutting Tool is a one-piece tool designed to cut holes up to 4 " (127,0 mm) in carbon
and stainless steel pipe. This allows for use of Mechanical-T , Vic-Let, Vic-O-Well and Snap-Let outlets.
Technical Data:
Capacity: - 4" (21,3 - 114,3 mm) pipe, 1 - 4" (33,7 - 127,0 mm) holes for Mechanical-T and Vic-Let
Power Requirements: 110V/1ph/60 Hz (7.0 amp)
Weight: 23 lbs. (10 kg)
Shipping Weight: 48 lbs. (22 kg)
Intended for field fabrication.
VHCT900
The VHCT900 Hole Cutting Tool is a three-piece tool designed to cut holes up to 3" (88,9 mm) in diameter
for Mechanical-T, Vic-Let, Vic-O-Well and Snap-Let outlets. The base unit clamps quickly onto the pipe in
vertical, horizontal or overhead positions. The heavy-duty drill mounts to the alignment guides and a manual feed assembly provides uniform pressure on the saw for maximum cutting efficiency.
Technical Data:
Capacity: 1 - 8" (42,4 - 219,1 mm) pipe, 1 - 3" (25,4 - 88,9) holes for Mechanical-T, Vic-Let, Vic-O-Well and
Snap-Let Outlets
Power Requirements: 125V/1ph/50 - 60 Hz (7.5 amp) (220V 50/60 Hz available on request)
Weight: 36 lbs. (16 kg)
Shipping Weight: 53 lbs. (24 kg)
Accessories: Extended chain for 10 - 24" (273,0 - 610,0 mm) pipe
Intended for field fabrication.
Vic-Tap
Hole Cutting Tool
Vic-Tap Hole Cutting Tool is designed for use with Style 931 Vic-Tap II Mechanical-T unit for tapping into
steel pipe systems under pressures up to 500 PSI (3450 kPa).
Technical Data:
Capacity: Vic-Tap II 4 - 8" (114,3 - 219,1 mm) Run 2" (63,5 mm) (IPS) Outlet
Power Requirements: 115V/1ph/60Hz, 7.5 amp
Weight:
(A) Drill Guide Base 15 lbs. (6,8 kg)
(B) Drill Motor and Feed Assembly, Total wgt. 16 lbs. (7,3 kg)
(C) Style 931/Valve Unit, 12 - 15 lbs. (5,4 - 6,8 kg), depending upon size
Shipping Weight: Vic-Tap II complete, 75 lbs. (34 kg)
Hole Size: 2" (60,5 mm)
FIGURE 1: Parts A and B are designed for use with Style 931 Vic-Tap Mechanical-T units. Part C is the valved outlet for use under pressure up to 500 PSI.
Part A Includes drill guide base with extended shaft, arbor, pilot drill, 2 " hole saw, packing gland and HP-70 Rigid Coupling for
connection to Style 931.
Part B Includes drill motor with ground fault interrupt and clip-on feed wheel assembly.
Part C Style 931 with 2" (73,0 mm) full port ball valve factory mounted. Available in sizes 4 2" (114,3 73,0), 52" (141,3
73,0), 62" (168,3 73,0) and 82" (219,1 73,0). Available for purchase only. (Parts not sold separately).
Figure 1
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 17
VCT1 Manual
Pipe Cut-Off Tool
Lightweight (22 lbs./9,9 kg) and portable, this cut-off tool handles 4 - 24" (114,3 - 610,0 mm) pipe, up to
0.500" (12,7 mm) thick. A worm gear drive crank handle provides smooth, manual travel, easy control and
accurate cutting.
Technical Data:
Capacity: 4 - 24" (114,3 - 610,0 mm)
Wall Thickness: 0.065 - 0.500" (1,65 - 12,7 mm) (with tips supplied)
Tips: Acetylene - 1 ea. #00, #0, #1
Weight: 22 lbs. (9,9 kg)
Shipping Weight: 28 lbs. (12,7 kg)
Intended for field fabrication.
VCT2 Automatic
Pipe Cut-Off Tool
Rotation is powered by a small 120 VAC motor with SCR remote control. Unique tip design has stainless
steel insert which extends tip life, eases cleaning and reduces backfire.
Technical Data:
Capacity: 6 - 24" (168,3 - 610,0 mm)
Wall Thickness: 0.065 - 0.500" (1,65 - 12,7 mm) (with tips supplied)
Tips: Acetylene 1 ea. #00, #0, #1
Speed Control: SCR
Power Required: 120V/1 ph/60 Hz (15 amp)
Motor Rating: 15W 10,000 rpm
Weight: 33 lbs. (15 kg)
Shipping Weight: 49 lbs. (22 kg)
Accessories: Guide rail is sold separately. Recommended for pipe 12" (323,9 mm) and above. Order Guide Rail D600 for up to 24" (610,0 mm) pipe (others available).
Intended for field fabrication.
Designed to clean, deburr, and mark pipe ends for FIT products the PCT II provides job-site or limited production shop cleaning for pipe from 1 - 2" (33,7 - 60,3 mm). PCT II is provided complete with stand, 120-volt
AC motor and automated pneumatic cleaning wheel feed. Foot switch control leaves the operators hands
free to handle pipe. An abrasive wheel cleans pipe in a few seconds. An integral wheel marks the pipe and
removes the burr.
Technical Data:
Capacity: 1 - 2" (33,7 - 60,3 mm) IPS Schedule 10 - 40 Steel Pipe and Dyna-Flow pipe
Power Requirements: 115V/1ph/60Hz (20 amp)
Weight: 142 lbs. (64 kg)
Shipping Weight: 230 lbs. (104 kg)
Accessories: Abrasive Cleaning Wheels, Spare Parts
Intended for field fabrication.
24.01 - 18
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
GROOVING TIMES
Time for pipe preparation obviously depends on widely varied factors including productivity, location, type, hardness, and
wall thickness of pipe. As a gauge for typical grooving times, the following chart was prepared to include grooving time
with pipe in position and tool properly set for the size and depth of groove. Times will be extended when going from one
size to another for roll changes, depth stop setting, trial grooving and other minor adjustments incidental to changing pipe
sizes or initial set-up time prior to the first production groove.
Cut Groovers
Vic-Groover
Nominal
Size
Inches
226
272FS
1
1
1
2
2
3
3
4
4
5
6
8
10
12
14
16
18
20
22
24
30
36
0.5 #
0.6 #
0.7 #@
0.8 #@
1.0 @
1.3 @
1.4 @
1.4 @
1.5 @
1.5 @
1.6 @
1.8 @
0.3
0.3
0.4
0.4
0.5
0.8
1.0
1.5
1.7
2.0
2.5
270FSD 276FSD
0.2
0.2
0.2
0.2
0.3
0.3
0.4
0.4
0.4
0.6
0.8
1.2
1.5
1.8
2.3
0.3
0.3
0.4
0.4
0.4
0.6
0.8
1.2
1.5
1.8
2.3
268
274
416FS
416FSD
0.2
0.2
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.6
0.8
0.8
0.9
1.5
1.8
0.3
0.3
0.4
0.4
0.5
0.6
0.8
0.8
0.9
1.5
1.8
0.3
0.3
0.4
0.4
0.5
0.6
0.8
1.0
1.7
2.5
3.5
3.8
4.0
414
424
436
Power
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.4
0.6
0.7
0.8
1.1
0.2
0.2
0.3
0.5
0.8
1.1
1.4
1.8
2.0
2.3
2.5
2.8
3.0
0.2
0.2
0.3
0.5
0.8
1.1
1.4
1.8
2.0
2.3
2.5
2.8
3.0
3.8
4.5
0.5
0.5
0.7
0.7
1.0
1.2
1.4
1.7
1.9
2.3
2.5
3.0
4.0
Vic-Adjustable
Hand
VG28GD
Power
VG824
Power
1.5
1.5
2.0
2.5
3.0
3.8
4.5
5.5
7.0
8.0
9.0
10.0
15.0
1.0
1.3
1.5
2.0
2.5
2.8
3.5
4.5
5.0
5.0
8.0
10.0
12.0
16.0
20.0
23.0
27.0
30.0
# VE226B
@ VE226S
VE226M
* For roll groovers the times apply to the thickest pipe wall for which the tool is rated. See tool capacities. For cut groovers, the times apply to standard wall steel pipe. For other
materials and thicknesses contact Victaulic for details.
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
24.01 - 19
SIZE
Nominal
Inches
Schedule
Inches/millimeters
Pipe O.D.
Inches
Actual mm
millimeters
1.050
26,9
26,9
1,65
1,65
2,11
2,87
2,87
3,91
1.315
0.065
0.065
0.109
0.133
0.133
0.179
5S
0.065
5
0.065
10S
0.083
10
20
30
40
0.113
STD.
0.113
80
0.154
33,7
33,7
1,65
1,65
2,77
3,38
3,38
4,55
1.660
0.065
0.065
0.109
0.140
0.140
0.191
42,4
42,4
1,65
1,65
2,77
3,56
3,56
4,85
1.900
0.065
0.065
0.109
0.145
0.145
0.200
48,3
48,3
1,65
1,65
2,77
3,68
3,68
5,08
2.375
0.065
0.065
0.109
0.154
0.154
0.218
60,3
60,3
1,65
1,65
2,77
3,91
3,91
5,54
2.875
0.083
0.083
0.120
0.203
0.203
0.276
73,0
73,0
2,11
2,11
3,05
5,16
5,16
7,01
3.500
0.083
0.083
0.120
0.216
0.216
0.300
88,9
88,9
2,11
2,11
3,05
5,49
5,49
7,62
4.000
0.083
0.083
0.120
0.226
0.226
0.318
101,6
101,6
2,11
2,11
3,05
5,74
5,74
8,08
4.500
0.083
0.083
0.120
0.237
0.237
0.337
114,3
114,3
2,11
2,11
3,05
6,02
6,02
8,56
5.563
0.109
0.109
0.134
0.258
0.258
0.375
141,3
141,3
2,77
2,77
3,40
6,55
6,55
9,53
6.625
0.109
0.109
0.134
0.280
0.280
0.432
168,3
168,3
2,77
2,77
3,40
7,11
7,11
10,97
8.625
0.109
0.109
0.148
0.250
0.277
0.322
0.322
0.500
219,1
219,1
2,77
2,77
3,76
6,35
7,04
8,18
8,18
12,70
10
10.750
0.134
0.134
0.165
0.250
0.307
0.365
0.365
0.594
273,0
273,0
3,40
3,40
4,19
6,35
7,80
9,27
9,27
15,09
12
12.750
0.156
0.156
0.180
0.250
0.330
0.406
0.375
0.688
323,9
323.8
3,96
3,96
4,57
6,35
8,38
10,31
9,53
17,48
14
14.000
0.156
0.188
0.250
0.312
0.375
0.438
0.375
0.750
355,6
355,6
3,96
4,78
6,35
7,92
9,53
11,13
9,53
19,05
16
16.000
0.165
0.188
0.250
0.312
0.375
0.500
0.375
0.844
406,4
406,4
4,19
4,78
6,35
7,92
9,53
12,70
9,53
21,44
18
18.000
0.165
0.188
0.250
0.312
0.438
0.562
0.375
0.938
457,0
457,0
4,19
4,78
6,35
7,92
11,13
14,27
9,53
23,83
20
20.000
0.188
0.218
0.250
0.375
0.500
0.594
0.375
1.031
508,0
508,0
4,78
5,54
6,35
9,53
12,70
15,09
9,53
26,19
24
24.000
0.218
0.250
0.250
0.375
0.562
0.688
0.375
1.219
610,0
610,0
5,54
6,35
6,35
9,53
14,27
17,48
9,53
30,96
26
26.000
0.312
0.500
0.375
660,4
660,4
7,92
12,70
9,53
28
28.000
0.312
0.500
0.625
0.375
711,0
711,0
7,92
12,70
15,88
9,53
30
30.000
0.250
0.312
0.312
0.500
0.625
0.375
762,0
762,0
6,35
7,92
7,92
12,70
15,88
9,53
32
32.000
0.312
0.500
0.625
0.688
0.375
813,0
813,0
7,92
12,70
15,88
17,48
9,53
36
36.000
0.312
0.500
0.625
0.750
0.375
914,0
914,0
7,92
12,70
15,88
19,05
9,53
42
42.000
0.375
1067,0
1067,0
9,53
24.01 - 20
Victaulic tools incorporate technology protected by U.S., Canadian and International patents.
Victaulic
Tool Company
The Victaulic Tool Company, in Palmer,
Pennsylvania, houses assembly and testing
operations for Victaulic tools. Victaulic has been
designing, developing, and manufacturing tools for
over 50 years, and carries a full line of tools and
accessories for a wide range of pipe preparation in
the shop and in the field. All Victaulic tools are
designed for global use and can be prepared to meet
international electrical requirements. Literature in a
variety of languages, incorporating all international
pipe sizes, is available upon request.
WORLD HEADQUARTERS
P.O. Box 31 Easton, PA 18044-0031 4901 Kesslersville Road Easton, PA, USA 18040
Phone: 610/559-3300 FAX: 610/250-8817 http://www.victaulic.com e-mail: victaulic@victaulic.com
24.01 - 22
This product shall be manufactured by Victaulic Company. All products shall be installed in accordance with current Victaulic installation/assembly instructions.
Victaulic
incorporate
technology
U.S.,
Canadian
and International patents.
Victaulic reserves the right to change product specifications,
designstools
and standard
equipment
without protected
notice and by
without
incurring
obligations.