Professional Documents
Culture Documents
XMP2-32R-E
XMP2-32R-C
XMP2-32T-E
XMP2-32T-C
Index
Page
4
5
6
7
9
9
9
9
10
12
13
PLC instructions
Soft component range
Build a project
Communication function
3-4-1 Com port
3-4-2 Communication parameters
3-4-3 Communication mode
16
18
20
23
24
25
28
30
32
33
34
35
Page 2 of 36
LMAN009_R2V2
XMP2-32 Introduction
XMP2-32R/T introduction
Model
Function
XMP2-32R-E
16 DI, 16 DO Relay PLC, with a 7" colour TFT touch screen and
26 function keys, AC220V
XMP2-32R-C
16 DI, 16 DO Relay PLC, with a 7" colour TFT touch screen and
26 function keys, DC24V
XMP2-32T-E
XMP2-32T-C
1-3 Parameters
1-4 Dimensions
Page 3 of 36
LMAN009_R2V2
XMP2-32 family is PLC+HMI integrators. This family has 4 models as listed above. The 4 models
have the same aspect. Besides fulfilling the control requirements, XMP2-32 models can replace
the common HMI and PLC in the control system. The compact shape saves space and also
convenient for the maintenance engineer.
Page 4 of 36
LMAN009_R2V2
General specs
Input Voltage
AC220V
Power Consumption
Momentary Power-Off
Allowance
Voltage Endurance
Insulated Impedance
Operating Temperature
0~50
Storage Temperature
10~60
Ambient Temperature
Vibration
Anti-interference
Ambient Condition
No corrosive gas
Protection Level
IP20
Page 5 of 36
LMAN009_R2V2
1-2-2
HMI specs
Screen Property
Type
Screen Dimension
7 inch
Use Life
Display Area
480*234
Contrast
Not modifiable
Character setting
English, Japanese,
Character size
Touch mode
Picture
8KB
Data
4KB
Register
Page 6 of 36
LMAN009_R2V2
1-2-3
PLC specs
Item
Specs
XMP2-32R/T-E
Program format
Processing speed
0.5us
128KB
I/O points
8512
Points
Timer (T)
640
100mS timerSet time 0.1~3276.7 seconds
Specs
Points
Counter (C)
640
16 bits counterset value K0~32767
Specs
32 bits counterset value -2147483648~2147483647
Data Register (D)
2512 words
512 words
0~99mS
Password protection
6 bits ASCII
Self-diagnose function
Page 7 of 36
LMAN009_R2V2
Display and
touch area
Number keys
Function keys
Com Port
Power point
Download Port
Output point
Page 8 of 36
Input point
LMAN009_R2V2
1-3-1
LED display
1-3-2
Download port
The port is RS-232 standard and able to download PLC program and HMI screen.
Pin2
Pin3
Pin5
RXD
TXD
GND
Used as RS-485 com port: for HMI connecting with slave device
Pin1
Pin9
B
PRT (when HMI connecting with slave device, short pin
5&6)
DOWNLOAD (short pin 5&8 to force-download HMI
screen)
Pin6
Pin8
Attention:
1 Do not switch off when downloading, or you have to download again
2 The cable for downloading the HMI screen is the same as downloading PLC program
3 Do not download when XCPPro and TP software are both open
RS-232 download port is only used to download
1-3-3
Com port
1-3-4
RXD
TXD
GND
Port A and B
The port is RS-485 standard, is used to connect meter, inverter, extension model, etc.
Page 9 of 36
LMAN009_R2V2
Attention:
A, B port and RS-232 COM port is the same port, and cannot be used at the same time.
Page 10 of 36
LMAN009_R2V2
Page 11 of 36
LMAN009_R2V2
DC24V10%
7mA/DC24V
Input ON current
Above 4.5mA
Below 1.5mA
About 10ms
Circuit insulation
Photoelectric coupling
isolation
Page 12 of 36
LMAN009_R2V2
Below AC250VDC30V
Circuit insulation
Machine insulation
Action indication
LED light
Max load
Resistor load
3A
Induction load
80VA
Light load
100W
No
Minimum load
DC5V 2mA
OFFON
10ms
ONOFF
10ms
Response time
Transistor output:
Internal power
Below DC5~30V
Circuit insulation
Action indication
LED light
Max load
Resistor load
0.8A
Induction load
12w/DC24V
Light load
1.5W/DC24V
< 0.1 mA
Minimum load
DC5V 2mA
OFFON
0.2ms
ONOFF
0.2ms
Response time
Page 13 of 36
LMAN009_R2V2
Output connection figure:
Relay output:
Page 14 of 36
LMAN009_R2V2
Page 15 of 36
LMAN009_R2V2
Channel
Input
Counter
Highest frequency
CHL1
X0
C600
80KHZ
CHL2
X1
C602
80KHZ
CHL3
X3
C604
10KHZ
CHL4
X6
C606
10KHZ
CHL5
X11
C608
10KHZ
Counter
Highest frequency
Channel
Pulse
Input
Direction
CHL1
X0
X1
C620
80KHZ
CHL2
X3
X4
C622
10KHZ
CHL3
X6
X7
C624
10KHZ
Channel
Phase B
CHL1
X0
CHL2
CHL3
Input
Phase A
Counter
Highest frequency
X1
C630
80KHZ
X3
X4
C632
5KHZ
X6
X7
C634
5KHZ
Page 16 of 36
LMAN009_R2V2
Input
Pointer tag
Disable interruption
Rising interruption Falling interruption instruction
CHL1
CHL2
CHL3
X2
X5
X10
I0000
I0100
I0200
I0001
I0101
I0201
M8050
M8051
M8052
4. Frequency measurement
The point is X1, X11, and X12.
5. Pulse width modulation
The point is Y0, Y1.
1T type: Y0, Y1 available
2RT type: Y0, Y1 available
3R type: unavailable
6. Precision timer
32-bit precise timer, the timer range is T600 to T618, matching with 10-interruption tag.
Page 17 of 36
LMAN009_R2V2
Range
Point
Input point
X000~X017 (octal)
16
Output point
Y000~Y017 (octal)
16
Auxiliary relay
Status
Timer
Counter
Data register
FD
Flash ROM
Register
M0~ M2999
M3000~M7999
8000
M8000~M8511
512
S0~ S511
S512~M1023
1024
40
T620~T639vacant
C0~C29916 bits forward counter
C300~C31832 bits forward/back counter
C320~C59832 bits forward/back counter
C600~C618one phase high speed counter
C620~C628Pulse + direction high speed
counter
C630~C638AB phase high speed counter
D0~D999
D4000~D4999
640
2000
512
FD0~FD255
256
256
NOTE:
The memory area in is the defaulted power failure retentive area, the power failure
retentive area of soft components D, M, S, T, C can be set via FD register. For details,
please see the following table.
Flash ROM register neednt be set for power failure retentive area,
The serial number of input coil and output relay are octal data, other memory number are all
decimal data.
Page 18 of 36
LMAN009_R2V2
Address
type
Default value
Area
Function
FD8202
4000
D4000~D4999
FD8203
3000
M3000~M7999
FD8204
640
No set
FD8205
320
C320~C639
FD8206
512
S512~S1023
NOTE:
Users can set the power failure memory area.
Page 19 of 36
LMAN009_R2V2
Select XMP2-32:
2. Editing the PLC program
After selecting the type, user can edit the program in the software. The editing specs and
operating details please refer to XC Series PLC Edit Software XCPPro Manual.
The interface of software is as below:
Page 20 of 36
LMAN009_R2V2
3. Download program
After editing and saving the program, the user needs to download them to the XMP. Before
downloading, ensure the XMP has connected with computer successfully. Click
software serial port configuration
to open
When below window shows, it means the connecting is successful. Click OK to continue.
If the connection is not successful, the window will show communication error. Please check the
serial port and the cable.
Page 21 of 36
LMAN009_R2V2
Page 22 of 36
LMAN009_R2V2
3-4-1
Com port
XMP2-32R/T series product has program port (DB9 pins port), RS-232 COM port (DB9 pins port)
and RS-485 COM port (A and B point). Program port can only be used to download PLC program
and HMI pictures. However, RS-232 and RS-485 COM port can be used to communicate with
other devices. The communication parameters (baud rate, data bit, etc) can be set via software.
RS-485 COM port point A means + signal, point B means - signal.
Attention:
RS-485 and RS-232 COM port are the same; do not use them at the same time.
Page 23 of 36
LMAN009_R2V2
3-4-2
Communication parameters
Communication parameters of RS-232 and RS-485 COM port can be set via FLASH register in
the XMP.
The defaulted parameters:
Station 1, baud rate 19200bps, 8 data bits, 1 stop bit, even check
Station No.
Baud rate
300bps~115.2Kbps
Data bit
8 or 7 bits
Stop bit
2 or 1 bits
Check
Function
Description
FD8220
Communication mode
(Station number)
Communication format
FD8223
FD8224
Start symbol
FD8225
End symbol
FD8226
FD8221
COM Port FD8222
Page 24 of 36
LMAN009_R2V2
Setting up communication
FD8221:
15
14
13
12
11
10
0No check
1Odd
check
2Even
check
0300bps
1600bps
21200 bps
32400 bps
44800 bps
59600 bps
619.2K bps
738.4K bps
857.6K bps
9115.2K bps
02 stop bits
21stop bit
08bits data
17bits data
FD8226:
15
14
13
12
11
10
Reserved
Page 25 of 36
LMAN009_R2V2
3-4-3
Communication mode
Modbus communication
XMP series product support master and slave mode of Modbus communication.
Master format: When PLC is set to be master station, PLC sends request to other slave station
devices via Modbus instructions, other devices respond to the master station.
Slave format: When PLC is set to be slave station, it can only respond to other master devices.
The defaulted status of XMP is Modbus slave mode.
Communication address
The internal soft units numbers of XMP correspond with Modbus station address numbers.
Please see the following table:
Coil space: (Modbus address prefix is 0x )
Bit component address
M0~M7999
0~7999
0~1F3F
X0~X511
16384~16895
4000~41FF
Y0~Y511
18432~18943
4800~49FF
S0~S1023
20480~21503
5000~53FF
M8000~M8511
24576~25087
6000~61FF
T0~T618
25600~26218
6400~666A
C0~C634
27648~28282
6C00~6E7A
0~7999
0~1F3F
TD0~TD618
12288~12906
3000~326A
CD0~CD634
14336~14970
3800~3A7A
D8000~D8511
16384~16895
4000~41FF
FD0~FD5000
18432~23432
4800~5B88
26624~27135
6800~69FF
FD8000~FD8511
Page 26 of 36
LMAN009_R2V2
4-1HMI function
Page 27 of 36
LMAN009_R2V2
Key
Function
Running the program, LED indication light
Stop running the program, LED indication light
Default main menu or most used screen.
Turn the screen to the last page
Turn the screen to the next page
NOTE:
Besides the function listed in the previous table, all the keys can be defined as the function of
force ON, force OFF, reverse or momentary ON.
Page 28 of 36
LMAN009_R2V2
Please see below picture. Open TouchWin software, put a button or function button in the
screen. Press, enter in the window, all the key-presses can be found in this menu. The user can
set the key function as they need.
Page 29 of 36
LMAN009_R2V2
Note:
For software user details please refer to TP Touch Screen User Manual.
After completing the project editing and saving, connect the download port of the XMP and
computer serial port with the downloading cable. Make sure the XMP power is on. Click
File Download to start downloading data, the download window is as below:
or
If it appears the item connection overtime, check cable, please download again.
Page 30 of 36
LMAN009_R2V2
The downloading is completed when it shows the below window:
Attention:
(1) Do not cut the power when downloading, or you have to download again.
(2) The downloading cable for the TouchWin screen is the same as the downloading PLC
program.
(3) Do not download when XCPPro and TouchWin software are both open.
Page 31 of 36
LMAN009_R2V2
5-1 Summarization
5-2Extend MA model
5-1 Summarization
XMP2-32R/T series product cannot extend BD board.
For extending other devices, use RS-232 or RS-485 (point A and B) COM port.
RS-232 COM port can connect with the computer, HMI to monitor the program.
RS-485 COM port can connect with meter, inverter, function model, etc. It can extend 32 external
devices at most.
Attention:
The connection method is Bus mode, transmission line should start from station 1 to station 2,
and then from station 2 to station 3connect in this sequence until the last station. Star mode or
ring mode connections are not permitted.
Page 32 of 36
LMAN009_R2V2
XMP2-32R/T series product can extend MA model via RS-485 COM port (A and B point) in order
to control and measure analog signals.
The type and specs of MA model are as below:
Type
Function
MA-8DA
MA-7PT-P
MA-8TC-P
Page 33 of 36
LMAN009_R2V2
5-2-2 MA model specs
MA-8DA:
Item
Voltage Output
Current Output
DC0~5V0~10V
DC0~20mA4~20mA
Resolution
1/1024(10 bits)
Integrated Precision
0.8%
Scan speed
COM port
RS-485
DC24V10%, 100mA
Insulation Format
Installation format
Dimension
140W73H90D
MA-7PT-P:
Item
Content
Temperature
measurement range
-100 ~350
Control precision
0.5
Accuracy
0.1
Integrated precision
Scan speed
100ms7 channels
Dimension
63mm102mm73.3mm
Page 34 of 36
LMAN009_R2V2
MA-8TC-P:
Item
Content
K type thermocouple
0 ~1000
Control precision
0.5
Accuracy
0.1
Integrated precision
Scan speed
100ms8 channels
DC24V10%50mA
Installation Format
Dimension
63mm102mm73.3mm
Page 35 of 36
LMAN009_R2V2
Documentation Reference
Document Number
LMAN
009
R2
Revision Date
V2
17/07/2012
For help and support regarding your XINJE products visit the online
Support Centre or contact us on: support@listo-ltd.com.
www.listo-ltd.com
www.xinje-support-centre-listo.com
Page 36 of 36
LMAN009_R2V2
Contact us
Listo Ltd.
25B Antrim Business Park
Enkalon Industrial Estate
Antrim
Co.Antrim
Northern Ireland
BT41 4LD
+44 (0)28 944 64968
info@listo-ltd.com
www.xinje-support-centre-listo.com