Professional Documents
Culture Documents
SYSTEM ON EQUIPMENT
REPLACEMENT
By
Sium Tecleab
Advisors
Dr. R. N. Roy
&
Ato Fantahun Melaku
June, 2002
ACKNOWLEDGEMENTS
I wish to express my sincere gratitude and indebtedness to Dr. R. N. Roy and Ato Fantahun
Melaku, my advisors, for invaluable guidance and supervision for completion of the thesis. I
also would like to thank them further for arranging their advice time understanding the
constraints that I had.
I extend my deepest gratitude to W/r Askale Letyibelu and their family, Ato Feleke Atnafe,
Ato Million Dirara, Ato Hinsene Samaro, Hebteslasie Berhie, and W/t Letay Minasie for they
have lend me their hands and constant encouragement to stride along the path I have chosen
and complete this work.
Deep and honest appreciation goes to Ato Abdulalim Mussa, Leaf Spring Project Owner, for
gladly arranging time of project working hours for the sake of my thesis completion.
I am also deeply indebted and would like to express my gratitude to Ato Zewdu Nugatie for
his cooperation in collecting data and relevant information.
Heart felt gratitude and acknowledgement is also due to Senbetu Asgedom, my wife, for
creating conducive condition and bearing most of the family affairs during the course of my
study.
Above all, I thank God for all the power he has given me to stay under his umbrella and
complete this thesis.
.
CONTENTS
Chapter-1: INTRODUCTION
........................................................................
1.1
Objective
............................................................................
1.2
Methodology
...........................................................................
1.3
.................................
2.1
2.2
2.3
...............................................
2.4
Latest Developments
...............................................
12
..............................................
14
14
3.1
3.2
.............................................................................
16
3.3
Sudden failures
..........................................................
24
3.4
Obsolescence
.......................................................................
27
3.5
Life of an equipment
...........................................................
28
ii
3.6
...................................
28
3.7
.................................
30
3.8
.......................
41
3.9
.......................
42
..............................
44
.......
4.1
4.2
4.3
4.4
...............
46
..........................................................
61
Problem identification
...........................................................
66
Chapter- 6:
44
..................
69
5.1
General
...................................................................................
69
5.2
70
5.3
System Design
71
5.4
5.5
Data collection
IMPLEMENTATION
6.1
Implementation
6.2
Justification
.......................................................................
.............................................................
......................................................................
...............................................
iii
83
83
87
...........................................................
87
.......................................................
88
6.3
Chapter- 7:
Method of Implementation
...........................................................
.........................
90
.........
90
..
91
Bibliography
...
92
Appendix A
..
95
Appendix B
. 102
Appendix C
89
7.1
7.3
Conclusion
...
iv
108
Chapter 1
INTRODUCTION
1.1 Objective
Industrial enterprises, since the inception of operation, are faced with equipment maintenance,
repair, change of parts and components and lastly replace the equipment. The replacement
may be done with another equipment of similar design features or one, which has better
output, less maintenance cost, less power consumption or technologically advanced one in
one or the other way. The questions that arise during replacement of equipment are:
These and the like problems should be dealt with, before the decision for replacement is
made.
To reach the decision of replacement all the factors that affect the decision should be
enumerated and analyzed. The analysis can be subjective or objective. However, in most
circumstances the objective factors are given less emphasis. This is because of the improper
handling and processing data to get meaningful information that aids objective analysis and
leads replacement to be at most economical time. In short, the idea of replacement should be
raised when it is most economical rather than when the operational cost is very high.
On the other hand, the replacement of equipment from the economic point of view should be
compared with the economy of an existing actual and realistic book value of the equipment
rather than with its original first cost [2]. That is when replacement is considered
(contemplated); the analysis should reveal the present realities and consider the future. Based
on this framework the objectives of the thesis are:
To develop a system that can facilitate the decision making activities on the
replacement of deteriorating equipment,
1.2 Methodology
Even though the problem of equipment replacement was clear, understood and experienced by
the student there has to be concrete data to portray this. To do so the following methodologies
where employed to get necessary information.
Data were collected from two industries such as review reports on maintenance
related activities, capital budget etc.,
Review the existing methods and policies employed on equipment replacement and,
Providing the organization with a means for controlling the borrowing and
expenditure of capital,
Chapter 2
LITERATURE REVIEW
This chapter indicates brief historical development of equipment replacement systems and
some of the attempts and models of replacement problems that have been formulated for
equipment that are subjected to degradation or deterioration through operation. Further the
application of principles of replacement, assumptions made on equipment replacement tools
and methods employed on equipment replacement are covered.
The theory of renewal and replacement and mathematical theory of failure have been
developed over the past 100 years. The early replacement decision rules that where in use
were not based on the development and solutions of mathematical models. These rules, such
as replace when equipment is fully depreciated, replace when the unit cost of production is
maximum or replace when equipment is worn out etc. which are in use even today, have
never been established as an optimal solution to any situation[2].
Today the theory is related to the characterization of a process as one of an established class
and the estimation of the values of the relevant functional parameter. The early developer of
a theory for equipment replacement model based on explicitly stated assumptions of a linear
operating-cost function that is time dependent with known constant parameters values was
Terborgh in 1949. It was after Terborgh that extensive studies and models formulated on
equipment replacement depending on the prevailing situations. The studies followed have
divided equipment replacement studies to be for items that deteriorate and items that fail
suddenly with out remarkable decrease in performance [2].
Deterministic models have been developed for most problems. An analytic or mathematical
form is established,
E = E(Xi, Yj)
which relates the system's performances as measured by E to the values of the control
variables Xi and the uncontrollable variables Yi. The Yj are usually expressed in terms of the
time parameter t where Yi (t) is assumed to be a known function of t. The major assumptions
made for measuring of system performance and developing a model were generally based on
one of the following objective functions in quantitative terms[2].
Terborgh's Model
Terborgh (1949) was the first to develop a theory for equipment replacement based on
explicitly stated assumptions of a linear operating cost function that is time-dependent with
known constant parameter values.
E=
Where C
(n 1)
A S r
c+
+ ( A + S ) ..
2
2
2.1
The combined cost per year E is a sum of two terms; the first increases with equipment age
(operating inferiority) and the second decreases with increasing age (capital cost). The first
term in the brackets of 2.1 is the average capital cost per year. The second term in the bracket
is approximately the average yearly cost of money over the period calculated by taking the
cost of (A-S) for a period of n-i years, in which payments are made annually, plus the cost of
borrowing S amount of money for n years.
In a research project conducted by the Machinery and Allied Products Institute (MAPI),
Terborgh extended his earlier work to cover general problems of capital investment. The
reformulation and extension of the basic principles are applied to the acquisition of plant and
equipment for the purposes of improving existing processes and of introducing new
processes.
Grant's Model
Grant (1950) discusses in qualitative terms the problem of when existing equipment should be
replaced on the basis of inadequacy, obsolescence, excessive maintenance, and declining
efficiency. He summarizes the qualitative formulations to date and presents procedures for
analyzing and reaching solutions to the economic-replacement problem where:
The value of money is constant over the life of the equipment, and
Dean's Model
Joel Dean (1951) was the first to state explicitly that capital investments for replacement
purposes ought to compete with other investments the firm is capable of making. He argues
that the return on investment should be used to evaluate alternative possibilities of capital
investment. The combined cost for current equipment (the sum of relevant operating costs
and the capital-wastage cost) is expressed as a function of equipment age. Replacement
occurs when the combined costs equal the average cost per year of the new equipment plus
the annual return on the capital outlay for the new equipment less the salvage value of the old
equipment. The point of replacement occurs after the annual cost of the old equipment
exceeds the average cost per year of the new equipment.
Orenstein's Model
Acquisition cost, A.
2.
3.
He defines the economic life as one that minimizes the average annual sum of the above,
t (t + 1) 1
A
A
+ r + Ft +
d
t
2
2
t
dE
A d
= 2 + =0
dt
2
t
E=
to =
2.2
2A
d
or the average increase in operating cost is equal to the annual depreciation value of the
equipment. The selection of alternative equipments would depend on the minimum values
of the total average costs over the life of each. Obsolescence is considered to be introduced
by increasing the interest rate, decreasing the life expectancy, or decreasing the salvage
value.
The models considered so far have assumed analytic forms for the cost functions. Sandiford,
Bernholtz, and Shelson (1956) considered arbitrary values for the annual costs and developed
numerical, iterative procedures for determining the economic life of vehicles. The measure of
performance chosen was the average annual cost over the replacement interval. The optimal
policy was use of that replacement interval which minimized the average annual cost, to be
determined for each group of vehicles [30].
The total average cost C was considered to be the sum of capital wastage (acquisition cost less
salvage value), interest, repair costs, and un-serviceability costs. Values of C were calculated
from historical data for each vehicle class by taking the cumulative averages and the
minimum obtained by inspection. The authors used historical data to obtain optimum
replacement intervals.
Clapham's Model
A 1
K (t ) = + f ( x)dt
2 t0
2.3
A is the acquisition cost, A/t is the annual capital depreciation, t life of the equipment and f(x)
is the annual maintenance cost of equipment of age x.. This model doesnt consider
discounting.
Fetter and Goodman (1957) have developed an electronic analogue of the equipmentreplacement model and have used it to solve the cost-minimization model formulated by
Terborgh as one application. In addition, a number of models are developed where the
solution is that replacement interval that maximizes the present value of all future returns
from the firm's use of equipment[12].
10
Rilas's Model
Rilas (1957) has developed a discrete-replacement theory that compares alternative policies
for replacement on the basis of discounted value of all future costs associated with each
policy.
Elmaghraby (1958) has indicated the need for considering obsolescence of equipment and,
therefore, for converting deterministic models into ones that are stochastic. His method of
converting an exact-replacement model into a stochastic one involving uncertain demand is to
assign confidence weights to the demand parameter in accordance with company expectation
and to compute a replacement policy that maximizes the expected return.
Barber (1958) has presented a method for introducing probabilistic functions for returns, as
forecasted by manufacturing engineers, to determine the economic feasibility of purchasing
an automatic machine. By weighting the possible payoffs with the probability of achieving
the payoff, and comparing the expected return with the rate of return on other corporate
investments, the machine to be purchase is decided.
11
The importance and cruciality of equipment replacement decisions is one of the major
challenges to organizations where the outcome is directly reflected on the organizations
change on production costs/rate, changes on the financial statement or change on capacity of
proper utilization of throughput etc. Latest development on equipment replacement decisions
is fully supported with the available tools, computers, to handle and process data to get
meaningful information. Due to its importance by this time the historical data handling system
is made to be accessible to every one who is ready to use it. To mention one is the Asset
tracking template presented by Microsoft Corporation, Database in Microsoft Access fig.2.1.
12
Asset Tracking
Module /
Macro
Form
Asset category
Asset
Table
Department
Asset category
Depreciation
Asset
Depreciation subform
Department
Employee
Depreciation
Employee subform
Employee
Maintenance
Maintenance
Maintenance subform
Switchboard item
Status
Status
Vendor
Vendor
Report
Asset by category
Asset Date Acquired
Asset by Department
Depreciation Summary
Asset by Employee
Maintenance History
Asset by Vendor
13
14
Figure 2.1
Asset tracking
Chapter 3
PRINCIPLES OF EQUIPMENT
REPLACEMENT
15
The problem of replacement arises after an industrial enterprise or project has been in
operation. The rate of replacing of equipment may vary due to internal factors such as,
sensitivity of the working area, and external factors such as competition. Depending on the
internal and external factors replacement problem can be due to the following reasons [7].
1. Replacement because of inadequacy
Equipment that is inadequate in capacity to perform the required service is a logical
candidate for replacement. The inadequacy in the amount and type of service requirements
can be due to:
Changes that may arise from competitive situations either from competition among
producers on a single industry or competition, which may arise with substitute
products,
16
since new equipment having higher/lower capacity is available to accommodate the new
demand level. On the other side the availability of improved machines performing the
same service with more economical ways and methods will pay to replace old assets with
new ones or to relegate them to stand-by purposes or other inferior uses for better
economical advantage. Further equipment can be obsolete if it is no more under
manufacturing.
4. Physical impairment
Equipment may be out of operation or perform less than expected due to damage or
improper handling.
5. Rental or lease possibilities
The development of equipment rental firms has caused some owners to change from an
ownership role to a lease role with regard to some expensive but infrequently used
equipment.
6. Change in public requirements regarding the machine or the product.
7. Sudden failing equipment
These equipment perform at about full capacity until failure.
The main reasons for equipment replacement can be divided into three broad categories:[14]
Sudden failures,
Obsolescence.
17
The problem of replacing various worn out spare parts of equipment is one, which arises in
every Organization. In some cases, instead of changing spare parts of an equipment, it may
be more economical to replace the equipment altogether specially if it has deteriorated with
constant use. To know whether it is feasible or not, economic analysis is very important.
As equipment gets worn out with time and usage it functions with decreasing efficiency.
Failure of equipment that are subjected to wear and tear (deterioration) is easily predictable.
On this type of failure, maintenance or upkeep of this equipment is usually practiced. Due to
the predictability of failure behavior changes on operating or maintenance cost or both can
easily be guessed. Likewise replacement policy should focus in analyzing the operating and
maintenance cost. Based on the analysis two conditions may be anticipated [3].
If the cost of operating and maintenance remains the same or decreases with time the
best policy is never to replace the item. This condition is hardly met in real situation.
If the costs fluctuate with time, the equipment should be replaced only when the cost
is in increasing trend.
Generally, costs of industrial equipment increase with time or age. Even though the increase
in cost necessitates replacement of the equipment, the rate of increase in cost may vary from
item to item. Due to varying rate in cost increase during operation, there is no clear and
defined time, which indicates the replacement of the equipment. Replacement of equipment
requires calculating the increase in operating costs, maintenance costs, forced idle time costs
and costs for replacing by new equipment.
18
Thus, at some stage it may be more economical to discard the old equipment and replace it
with a new one. The following factors should be taken into consideration while formulating
an appropriate system for replacing equipment [23].
3.2.1
Rate of Inflation
The price of an equipment does not remain steady with time. Thus, while formulating a
replacement policy, this factor should be taken into consideration. It can be considered by
assuming a certain rate of inflation. Thus, if the rate of inflation is (i) percent, then the price of
the equipment Cn after n years given that the present price C is
( )n
Cn = C 1 + i
3.2.2
Discount Factor
As the money value changes with time the calculation of equipment replacement should
include the interest rate (rate of inflation to have the present value of the money to be spent in
the future). [23]
Suppose the interest rate available in the market is r percent. Then, instead of spending an
amount C today we may obtain C1 = C(1 + r) a year from now, C2 = C (1 + r)2 two years
from now and Ck = C(1+ r)k k years from now. Looking from another point of view, an
amount Ck spent k years from now is equivalent to spending an amount C today. That is
19
C = Ck 1 + r
k
= CkV
) k
1
3.2.3
Operating Cost
Equipment incurs certain costs while in operation. It may be due to the application of some
ingredients like lubricant or fuel or due to maintenance etc. There are empirical evidences
that such operating costs increase with increasing age due to a variety of reasons such as
deterioration of components or wear and tear. Basic data on operating costs are necessary to
ascertain whether it is too high compared to acquisition cost or not [7].
3.2.4
Depreciation
Depending on its use depreciation has different meanings. Some of them are [14].
1. Decrease in value. This concept implies that the value (market value or value to the
owner) of one asset is computed at two different dates. The difference is the depreciation
regardless of what combination of causes may have been responsible for the value
change. This is the meaning generally implied on every day speech.
2. Amortized cost. It is an accounting concept of depreciation where the cost of an asset is a
prepaid operating expense to be apportioned among the years of its life by some more or
less systematic procedure. It should be emphasized that it is the cost not the value that is
allocated.
20
"Depreciation accounting is a the system of accounting which aims to distribute the cost
or other basic value of tangible capital assets, less salvage (if any), over the estimated
useful life of the unit(which may be a group of assets) in a systematic and rational manner.
It is a process of allocation not of evaluation. ...."[18]
3. Difference in value between an existing old asset and a hypothetical new asset taken a
standard of comparison. This is an appraisal concept of depreciation and money appraisals
of old assets. Appraisal depreciation means the value of inferiority at some particular date
(date of appraisal) of one asset, the existing old one being appraised to another asset, a
hypothetical new one used as basis of valuation.
4. Impaired serviceableness. As machines become older they are often unable to hold a close
tolerance as when they were new. Similarly, the strength of structures may be impaired by
the decay of the corrosion of metal members. This is sometimes called as depreciation to
refer impaired functional efficiency. It is not commonly used.
There are many different methods of writing-off cost. One common way of classifying
depreciation accounting method is:
1. Methods that aim to give a greater write-off in the early years of life than in the final
years of life such as declining- balance method, the sum of-the-digits method, Multiplestraight-line method.
2. Methods that aim to give a uniform write-off through out the entire service life, straightline method.
21
3. Methods that aim to give a smaller write-off in the early years of life than in the final,
sinking-fund method.
a.
It is common practice for assets to be used as stand-by or inferior uses during their final years
of their lives. Due to this their contribution is decreased. Equally the writing-off also is made
to decrease by using the declining-balance depreciation method. In declining-balance
depreciation method a given depreciation rate is applied each year to the remaining portion of
the cost of the asset (book value). For example, if a 10% rate is applied to an asset that costs
$35000.00 first year depreciation will be $35000.00 x 0.1=$3500. The second year cost will
be (35000.00-3500.00) x 0.1 = $3150.00 and the third year cost will be (35000.00-3500.003150) x 0.1 = $2835 and so on.
b.
The digits corresponding to the number of years of estimated life are added together. For
example, considering a machine having estimated life of 20 years, initial cost of $35000, and
salvage value of $3500 the sum of the digits from 1 to 20 is 210. The depreciation charge for
the first year is 20/210 of the ($35000-$3500) and in the second year the depreciation charge
is 19/210 of ($35000-$3500) and so on. This method writes-off about of the depreciable
cost in the first half of the estimated life.
22
c.
In straight-line method, the full service life and the net salvage value at the end of its life are
estimated. The annual depreciation rate to be applied to the first cost of the asset being
written-off is computed as follows:
Initial cost estimated Salvage value
Straight line depreciation charge =
estimated service life in years
d.
A real or imaginary sinking fund is established and a fixed deposit is made in the fund at the
end of each year (annual depreciation cost) in the life of the asset. The deposit is so computed
that the amount put into the fund plus the interest earned on it will just equal the amount by
which the asset is to be depreciated. The amount in the fund at the end of the life period is to
be equal to the depreciated value of the equipment or the difference b/n first cost and salvage
value [7].
Sinking fund amount = First cost salvage value
i
Annual depreciation cost = [sinking-fund amount] x
n
(1 + i ) 1
Where
= Interest rate
23
When the rates of interest approaches zero the sinking fund method yields the straight line
method.
a.
b.
Selling price of new equipment of similar grade; If the price of new equipment remains
at a uniform level, the salvage value will be equivalent to the original cost minus the
depreciable value as affected by its condition.
equipment has increased materially, the salvage value may be equivalent to the present
price minus the depreciable value as affected by its condition. Thus the salvage value
may approach and even be greater than the original cost of the equipment. Of course, if
the price goes down, the opposite will result and the salvage value will be very low.
c.
Reason for selling; The buyer of secondhand equipment is suspicious of the seller. He
is afraid that a poor buy is being unloaded on him. He suspects that the reason for
selling may be that the equipment has been inefficient in its operation or has some other
objectionable feature.
d.
Cost of removal; The salvage value of the piece of equipment may be fairly high. The
cost of removal may, however, be of sufficient amount to reduce materially the salvage
value. The cost of removal will depend greatly on the location of the equipment.
Removal from locations that are hard to get at or from those that involve shifting other
24
equipment may be very costly. If it is impossible to move other equipment easily, the
ease with which the equipment may be disassembled or broken up will affect the cost of
removal materially.
e.
Supply and demand; Supply and demand will affect the salvage value. The nature of
the market helps materially to set the price or value. In a seller's market the buyer must
pay if he wishes the equipment. In a buyer's market the seller is at the mercy of the
buyer. If the market is about even, neither one has the advantage over the other. The
market price thus arrived at is a fair price.
f.
Generally salvage value of equipment depends upon its age. The salvage value may be
predicted from experience or by using a suitable rate. If it is assumed that the salvage cost
reduces by a fraction k per year then an equipment having a value C will have a salvage value
Sn after n years, where
n
Sn = C(1 k)
Sometimes the devaluation of machinery is compounded m times a year so that
Sn
C1
25
Therefore, it is important to know in advance as to when the failure is likely to take place so
that the item can be replaced before failure. Quite often it is not possible to predict time of
failure by direct inspection like that of wear out items. The time of failure can be predicted
from the probability distribution of failure of past experience. The problem is then to optimize
the time, which minimizes the total cost to be incurred. That is, it is to minimize the sum of
the costs of the items, cost of replacing the items and cost associated with failure of the items.
Such type of replacement system is called preventive replacement.
26
Preventive replacement is a procedure, which provides for replacement after a time when the
effect of aging has become sufficiently critical, even if the actual failure has not yet occurred.
It attempts to optimize the trade-offs between costs of pre-emptive replacement and costs of
failure. Preventive replacement is desirable under the following conditions:
The cost of sudden failure is high relative to that of preventive replacement.
The component or the spare part which is being replaced during preventive
maintenance has a life x which is a stochastic variable or the probability distribution of
life has an increasing failure rate (IFR).
Based on this principle there are two types of replacement policies.
27
some, which may be almost new. The typical example is the replacement of light bulbs in a
large office where the replacement of every single bulb at failure becomes rather expensive.
In this case, taking a specified time the entire group of items is replaced periodically. By
using group replacement, individual failures and replacement between two successive periods
become fewer in number.
3.4 Obsolescence
In addition to the reasons mentioned in section 2.2 equipment may become obsolete due to
different reasons.
1. The equipment may be fit for operation intended or it may perform the designed
standards. But due to technological advancement better equipment may be designed which
performs the job with less cost and better safety or the manufacturer might have changed
the product type so that spare part sourcing may be difficult.
2. Obsolescence may be created due to loss of market of the product of the equipment. That
is the product may lose value because of new product came into the market which
customers prefer.
The greatest obstacle in developing a replacement policy for equipment that fail due to
obsolescence is that predicting the economic effect of future technological progress in that
field. The progress in technology may be gradual, long run improvement or frequent dramatic
advancement, which have revolutionary effect [21]. On the latter case it is very difficult to
predict very far in the future. Better prediction of the future can be made of the more gradual
types of technological advancement but only with great difficulties in some area. In some
studies for equipment with gradual technological progress it is taken to be linear prediction,
28
which relatively is very simple to analyze. With this assumption it is possible to answer the
question what is the economic life of equipment that is one of a technologically developing
sequence having a constant rate of improvement over time.
As the nature of failures is of different types the replacement system is also different. This
paper fully focuses on the first failure nature or on replacement of capital items that
deteriorate with time and operation.
The formulation and implementation of a good replacement policy plays a major part in the
determination of technical and economical progress of an organization. Inadequate
replacement policy, on the other side, may be disastrous to a firm. To defer the replacement of
29
equipment sometimes may lead to a decline in output and in the long run a business recession
may be eminent.
Replacement of equipment depends on different factors and some of the factors are not easily
determined or expressed and do not force us to take action at certain fixed time. Therefore an
assumption, which can reflect the reality and simplify the analysis of replacement policy, is
very important. Some of the major issues that need assumption are [21]:
1. Planning Horizon
It means the points of time furthest, in the future which is considered in the formulation of
the policy. It can be divided into two.
Finite planning horizon where the Industry/project will have a definite and predictable
duration and that the formulation of replacement policy might be more realistically
based upon.
2. Technology
Refers to the development of the innovative measures made on machines, which are
candidates to replace those under operation. If the assumption of future machines that
replace the existing once were to be the same then we are saying there will be no
technological progress in the area. However we may wish to recognize that machines
which will be available in the future are more efficient, reliable, or productive than those
on the market. This assumption leads to recognition of obsolescence. The problem is, of
course, to quantify the phenomenon of obsolescence so that it can be applied analytically
to the formulation of a policy.
30
These varieties of issues may suggest to a large number of different possibilities for
developing replacement policies and models. For example if an item is assumed to have no
salvage value the model to be developed is different to from the one, which do have a salvage
value.
31
Assuming that the proposal is to replace a machine by another one, the factors to be
considered for both equipments will be somewhat as follows:[7]
Present equipment
Proposed equipment
1.
First cost
First cost
2.
Operating cost
Operating cost
3.
Life, estimated
Life, estimated
4.
income tax
income tax
5.
6.
Number of pieces
Number of pieces
for depreciation
for depreciation
8.
Present age
Technology
9.
compatibility
10.
Availability
7.
At the same time, the capital recovery cost decreases. The combination of
decreasing capital recovery costs and increasing annual operating and maintenance cost
results in the equivalent uniform annual cost.
32
By forecasting the operating and maintenance costs for each year of service, as well as the
anticipated salvage values for various replacement ages, one can determine the replacement
interval for an equipment. Based on this, there are three main methods of justifying equipment
replacement
Since each piece of equipment has its own identification number, the method of computing
costs against each of the coded machines is to tabulate the total hours the machine has been
utilized and the repair, maintenance, and fuel or power costs for the machine. This gives an
average cost per hour of operation that can be compared to the repair and maintenance costs
that have been tabulated for the whole equipment in the system. Equipment whose expenses
are much higher than the average of the total equipment in consideration should be replaced.
The estimate of the savings to be derived from replacing such older equipment would be the
justification.
Equipment replacement can be justified in another manner by increased cost per hour of
operation. By carefully tabulating all of the costs incurred for each piece of equipment and
making a chart for each equipment the curve that is formed by the cumulative costs per
certain fixed intervals of operation will indicate the manner in which, as the equipment ages,
it will increase in hourly operating costs per specified hours. In this method, equipment
33
replacement is justified when cumulative costs show a sharp increase over the prior fixed
intervals.
The lowest total cost point or the LTCP concept is based on the fact that a cost curve can be
made for each of equipment as shown in figure 3.1. This total cost curve is derived by
charting the sum of the cumulative maintenance cost per specific time and the cumulative
ownership cost per specific time of operation. By projecting the total cost curve into future, it
is possible by extrapolation, to plan an equipment replacement before major repair become
necessary. It is possible to derive the ownership cost curve by decreasing the purchase cost at
a certain declining rate. The cost curve for maintenance indicates the total amount spent in
maintaining the unit in operating condition. All normal wear and tear items are included in
maintenance costs except those repairs, which are caused by the operators abuse.
The total cost curve for a particular unit is obtained by adding the maintenance cost curve to
the ownership cost curve. The point needed is that period in which the equipment will be
operating at its lowest total cost. After the lowest total cost point the equivalent uniform
annual cost curve starts to rise that is the equipment starts to consume progressively the
revenue generated. Even though the cost curve will begin to rise, and it is at this time that the
equipment will be ready for replacement, it does not mean that it is the cutoff point for
replacement of the equipment.
34
Fig.3.1 LTCP
In the first two methods the replacement of the equipment is made only after incurring
expense to repair the equipment. This is the cost, which drives the price per hour of operation
up beyond the economic range. Method three anticipates increased repair costs and
recommends replacement before these expenses are incurred.
The benefits in using the LTCP method for equipment replacement are:
1. Consistency: the LTCP method provides a consistent way of determining when to
trade in equipment. It eliminates the very subjective approaches that are sometimes
made by plants in replacing equipment, since it provides definite guidelines and
formalizes the entire procedure on a sound economic basis.
35
2. Eliminates costly major overhauls: when the LTCP is charted, you can predict trends
in equipment behavior and make forecasts, thus enabling you to extrapolate to forecast
equipment requirements. For example if the Equipment were nearing the LTCP, then
it would not be advisable to spend large sums for major overhauls. On the other hand,
if the LTCP is not forecasted to be imminent, then it might be decided to go ahead
with an equipment rebuild than preparing for replacement of the unit.
3. It minimizes general maintenance
When the LTCP method is used the reports of maintenance and operation enable to single
out high maintenance cost units. The LTCP charts provides an opportunity to look at the
equipment in retrospect and examine specifications, the operating conditions, and to
ascertain the reasons why the cost for particular equipment is either out of line or is
working in a hostile environment.
4. Equipment justification
Using the LTCP method is one way of helping to prepare requests for capital funds, since
it gives more credibility to the justification of equipment.
5. Budgeting
The LTCP method enables to forecast equipment requirement in a manner that tells when
to replace the equipment. The knowledge of when the equipment will be required and the
necessary funding that take place requires time. The LTCP gives time to place the request
in budget, get approvals, and have the equipment placed in the manufacturers schedule
for construction, thus reducing sometimes delayed delivery times and higher prices. The
advance notice that LTCP can give management serves as a much-needed forecast for
equipment expense.
36
Putting in to account all costs that depend upon the choice or age of the equipment a
replacement model can be developed. However, if the cost do not change with the age of the
equipment ( such as electric cost and labor cost in some special cases) it may not be included
in the calculation.
Considering the general condition where maintenance and operation costs increase with time
and money value also changes with time the present value of money to be spent a few years
hence can be calculated.
Let
Tave
f(t)
discount factor
( )n
= 1+ i
=
where
1+ i
37
Assuming Salvage value to be zero and all payments are made at the beginning of each year,
the present value of expenditure in n years is
Pn = C + R1 + vR2 + v2R3 + ... v
n-1
Rn
.....................................
3.1
Pn increases as n increases which means that the present worth, if the machine is replaced
after n+1 years is greater than after n years. Thus for any additional amount spent we get extra
years service. We are there for, interested in finding some function of the replacement interval
which allows for this.
Let us assume that the owner invests the amount Pn is borrowed money at the interest i and
repaying it off in fixed annual payments, each of value x, throughout the life of the machine.
Thus after n years total cost Pn of the machine will have paid off.
The present worth of fixed annual payments, each of value x for n years is
n
n 1 1
x +x + x + ... +
x=
x.
1
2
P =
x.
n 1
x=
P
n
1 n
...............................................................................................................
3.2
Thus the best period to replace the machine is the period x which minimizes x. however, since
is a positive constant the period at which to replace the machine is the period which
38
minimizes
F
n
P
= n .
1
differences approximation can be used to calculate its optimal value. by this method, n will be
optimal that is Fn will be minimum if
Now
...........................................................................................................................
3.3
Fn = Fn+1 + Fn
............................................................................................................................
3.4
= n +1 + n .
1 n + 1 1 n
(1 n)P
(1 n + 1)P
n +1
n
=
(1 n + 1)(1 n)
Further
n +1
(P
P ) + ( n + 1P
nP )
n
n
n
n +1
+
1
+
1
(1 n + 1)(1 n)
= (C + R1 +
R2...
n 1
.................
3.5
Rn ) + n Rn+1
= P + n Rn+1
n
Therefore
F n
1
(1 n + 1)(1 n)
1
(nR
) + ( n + 1P ) n{P nR
n +1
n
n
n +1
( nR
)(1- n) nP (1 )
n
+
1
n
(1 n + 1)(1 n)
1 - n
=
Rn + 1 Pn
n
+
1
n
1-
(1
)(1 )
39
................................................
3.6
1 - n
= A positive constant. 1 - n + 1 n
1 - n 1
1 - n
P
R
n + 1 n 1 < 0 < 1 - n + 1 n
1-
..............
3.7
1 - n
Rn+1 Pn
1 -
Rn+1 > Pn
Rn+1 > P
n
>0
1-
1 -
1 - n
1-
C + R + R + 2R + ... + n 1R
1
2
3
n
Rn+1 >
2
n
1
1 + + + ....+
C+
R n+1 >
r =1
n
.................................................
3.8a
R r 1
r
r 1
.................................................................................
r =1
40
3.8b
Or next periods cost is greater than the weighted average of the previous costs since the
R.H.S in equation 3.8b is the weighted average of all costs up to and including period n-1.
1+ +
+ .... +
n 1
C+
R n +1 <
r =1
n
........................... 3.9a
R r 1
r
r 1
..................................................
3.9b
r =1
Or next periods cost is less than the weighted average of the previous costs since the R.H.S in
equation 3.9b is the weighted average of all costs up to and including period n-1.
From equation 3.8b and 3.9b
The machine should be replaced if the next period's cost is greater than the weighted
average of previous costs.
The machine should not be replaced if the next period's cost is less than the weighted
average of previous costs.
The corresponding minimum annual payment x can be obtained from equation 3.2.
further if x1 and x2 are the minimum annual payments for two machines A and B, A
will be preferred if x1 > x2 and vice versa
On solving the equation 3.8 & 3.9 tabular method is preferred. as shown below
41
Year of Salvage
Running
Discount
service
cost(Rr)
Factor
value (S)
Discount
r 1
(r)
Discounted
Salvage
value
C+
r =1
R r 1
r
Factor
Rr
r =1
r 1
8
C+
R r S r
r
r
9
n
r
r =1
10
Equivalent
Uniform annual
cost (8/9)
(S r )
42
There is risk or uncertainty associated with predicting the expenses of a new machine,
whereas one is relatively certain about the expenses of the current machine.
A decision to replace equipment is a stronger commitment for a period of time into the
future than keeping the existing equipment.
Management tends to be conservative in decisions regarding the replacement of costly
equipment.
There may be a limitation on funds available for purchasing new equipment, but no
limitation on funds for maintaining existing equipment.
There may be considerable uncertainty concerning the future demand for the services of
the equipment in question.
Sunk costs psychologically affect decisions to replace equipment.
An anticipation that technological improvements in the future might render obsolete
equipment available currently; a wait-and-see attitude prevails.
Reluctance to be a pioneer in adopting new technology; instead of replacing now, wait for
the competition to act.
Observations of the practice of industrialists in such studies and of the published literatures
of the subject indicate four errors which it seems are often made in dealing with replacement
economy [14].
1.
Considering the excess of present book value over the net realizable value of the old
asset as an addition to the investment in the new asset. This error increases the apparent
43
cost associated with the new asset, and thus tends to prevent replacements that are really
economical.
2.
Calculating depreciation and interest (i.e., capital recovery) on the old asset on the basis
of its original cost rather than its present net realizable value. This usually increases the
apparent costs associated with the old asset, and thus tends to favor replacements that
are really uneconomical.
3. Where indirect costs (burden) are allotted in the cost accounting system in proportion to
direct costs (usually in proportion to direct labor cost), assuming without investigation
that a reduction of direct expenditures will effect a corresponding saving in indirect
expenditures.
replacements greater than the saving that is actually possible to realize, and thus tends
to favor replacements that are really uneconomical.
4.
In cases where the proposed new asset provides more capacity than the old asset,
comparing calculated unit costs realizable only with full-capacity operation, rather than
comparing the actual costs realizable with the expected output. Where such excess of
capacity is not likely to be used, this unit cost comparison tends to favor the asset with
the surplus capacity, and is therefore favorable to replacements that are really
uneconomical.
The first two of these errors cited result from a failure to recognize the true nature of
depreciation accounting as a time allotment against future dates of money already spent. The
third error results from a failure to understand clearly the nature of cost accounting
allocations. The fourth is merely an unrealistic use of unit costs.
44
Chapter 4
SURVEY OF EXISTING
REPLACEMENT SYSTEM
44
Equipment type
Reason for replacement, and
Important information of the equipment such as:
Purchase price,
Year of purchase,
Service years,
Capacity,
45
General
To know the actual methods and reasons employed on machinery replacement data recording
systems were assessed, request formats were collected and quite a number of questions were
asked. Some of the questions asked were the following.
What are the basic reasons for selecting equipment as a candidate for replacement?
The assessments show that major replacements employed in state owned industries could be
divided into three:
Forced replacement,
4.2.1.1
Forced Replacement
46
The replacement reason given to these equipments is that keeping the equipment in operation
becomes difficult due to one reason or the other. Forced replacement can arise due to different
reasons.
The failure of a machine during production season may be repeated where significant loss is
recorded. The basic failure of the machine may not be due to deterioration and end of its life.
But it may be due to poor maintenance or some other reason. For example a pump expected to
work for 6 years may fail repeatedly at the 3rd year. This failure can be due to poor erection,
poor pipe connection, poor alignment or poor follow up while in operation (for example,
leakage of oil may not have been given serious attention at the beginning which may result in
the damage of bearing and then bearing housing). Once the bearing housing is damaged
whatever spare is replaced failure rate will not be reduced and lastly shorten the life of the
machine. So such unknowingly neglected problem will result in an imminent replacement
before the machine reaches the expected life.
On the other hand the machine may have design problem which results in replacement before
it reaches its expected life. A good example for such replacement system is massecuite pumps
(sugar grain pumping) which have high wear rate at the tip of rotor and housing due to
pumping sugar grains. On some designs due to having liner on the rotor and housing,
replacing the liner will bring the pump to the required standard capacity. During wear out the
liners are replaced. If there is no liner in any one of the maintained parts, it is a must to
change the rotor and housing before completing one production season. Purchase of these
parts is too expensive and further on the middle of production the wear and tear of these parts
may result in decrease in capacity where production may be hampered. So due to these
47
problems even though the machines are relatively new replacement or design change becomes
inevitable.
a machine is working
perfectly to the satisfaction of the organization due to shift of production type, bankruptcy, or
else the supplier may stop production of such spare parts. Due to this sourcing of spare will be
impossible. For lucky areas batch-producing companies may take the responsibility to supply
spares. But over all the cost of spares will be extremely high where it is not bearable to
continue. Due to this replacement will be imminent.
During operation machines may fail due to technical problems or mal-operation. In such cases
replacement is initiated not on the formal way of replacement system.
Machines may be replaced after completing their life. The changes may not be planned and
programmed due to being beyond maintainability.
4.2.1.3
48
Most industries either slowly or at a fast rate make changes in production rate or production
system, type of product to meet the demand level. To do these changes it is inevitable to change
the layout of the machinery, tools etc. These changes bring about a complete replacement of small
or large machineries. With this type of revolution the machines to be replaced may not be at the
state of replacement stage either technologically or physically. Whether a machine is in a good
state or not if there is expansion in any aspect the equipment may be removed, or will be allowed
to work in parallel, put as a standby or transplanted. During this time the amount of capital on
these machines is considered in the following way.
Some of the equipments may have good salvage values so that the market may absorb them
and others may be discarded as a scrap.
Some of the machines may be rebuilt/rehabilitated and start a new life with the system,
Some of the machines may not be touched at all. Only additional machines in parallel be
installed.
For example the expansion of Metahara sugar industry from 3000 TCD (tones of cane per day) to
5000 TCD brought about a change in all the middle factory and back factory process equipment
to handle the on coming capacity of the two mills out put.
4.2.2
In most industries even though there is no proper equipment history recording and analyzing there
are some ways, which show whether a machine is performing good or not. For example
management holds meetings at different levels. During the meeting performance of the factory is
evaluated and the major reasons for downtime, performance decline etc. are discussed. This
49
discussion starts from the lower rank technical and production personnel. It is based on daily
records and reasoning generated by production/ technical personnel or reports from both. These
immediate responsible bodies discuss on the issues of down time, decline in efficiency and
conclude that the problem is either machine problem or mal-operation. Hierarchical by this
process continues up to the top management on weekly or monthly bases with different depth.
The analysis of the record is mostly used at the first stage to alleviate the day-to-day activities and
cumulative of this, even though it is not produced in a convenient way, to some extent it is used
for equipment replacement especially in short period basis.
4.2.2.1
The procedure followed for replacing a machine is more or less related to process of capital
budget approval. The major activities are as follows ( Fig 4.1).
1. Annually capital budget is requested in every organization. A reminding letter from the
General Manager to every department to present their requirement, within a specified time,
for the next year, initiates the annual budget request.
2. Based on the letter each department informs their sections to forward capital equipment
requirement. Each section assesses the data at hand, discusses within their staff and presents
their requirement for the coming year to their immediate boss (department). For example
under the technical department there may be four divisions, such as in case of Addis Tyre,
maintenance, design and planning, power and utility, and services and in case of Metahara
Sugar Industry, under the technical department there are electrical, mechanical workshop,
instrument workshop, fabrication workshop and maintenance. All these divisions and
workshops present their requirement to department head. The technical head collects all the
requests and calls meetings with his subordinates and discusses on the budget request jointly.
50
By crosschecking, commenting and suggesting other alternatives some of the requests may be
slashed off or others may be included for the budget year.
3. The final result of the department is presented to Deputy Manager. Equally the Deputy
Manager discusses the capital budget presented with his subordinates and makes necessary
changes.
51
Capital equipment
request for replacement
Heads of
Divisions,
Sections,
workshops
Reminding Letter
Yes
No
Yes
No
Request for
replacement (Deputy
G/Managers office)
Yes
No
Yes
No
Yes/No
Request for
replacement (Board of
Yes
No
Yes indicates the request is accepted, No Indicates the request is not accepted
52
4. The final result of the department is presented to Deputy Manager. Deputy Manager discusses
the capital budget presented with his subordinates and makes necessary changes.
5. The result of the discussion is the request of capital equipment for the year. This is presented
to the General Manager office.
6. The General Manager calls his subordinates and discusses on overall capital budget requests
and the capital estimates, source of funds, etc. and reaches a certain conclusion about which
equipment to defer, completely drop, or to accept the proposal as a whole.
7.
The capital budget request of the organization is compiled and presented to board of
directors. At this stage more or less the financial aspect of the budget request is given
emphasis.
8. The accepted draft capital budget request is then presented to the branch of Prime Minister
Office that is responsible to state owned industries. Here the final acceptance or rejection of
the request is made. What so ever the decision the document is sent back to the industries.
9.
After the approval of the capital budget a complete document under the heading of Capital
Budget Proposal of the coming year is released and each department is made to know it.
Sample is attached in appendix B. Then after the process of purchase starts.
4.2.2.2
Once it is decided to replace the equipment, and estimated budget allocation is made. The
purchase is done after passing quite a lot of activities. The following are the major activities in
purchase of a capital item [Fig 4.2].
1. Based on the capital budget approved, the design and planning office or any responsible
body prepares a tender document. This document contains technical specification and
evaluation method. The technical specification and evaluation method is prepared in two
53
sections. The first section contains points of fundamental compliance and the second
section all other criteria. Sample is shown in table 4.1. On the other side the sources of
purchase is divided into 3 categories. Items which can be bought from local; Items which
can be bought from sole manufacturers (non-standard) and items which can be bought
from any where (standard items).
2. At the same time based on the capital budget document each section generates a formal
request. The request is checked against the capital budget and presented to the General
Manager's office and is approved as necessary. It is then transferred to marketing.
3. Based on the technical specification the tender is released or sent to organizations known
for the type of items, which are recommended by technical department. The tender floats
with dead line.
4.
Proforma invoice is collected from all suppliers and opened by the tender
committee put their signature and it is delivered to design and planning office/ to some of
the committee members depending on the organization setup.
Based on the technical specification tender is released or sent to organizations known for
the type of items, which are recommended by technical department. The tender floats with
dead line.
Proforma invoice is collected from all suppliers and opened by the tender committee with
their signature and it is delivered to design and planning office/ to some of the committee
members.
Design and planning office/ some of the committee members prepare tender evaluation
table. The table contains on the first column the specification prepared by the
organization, and then after responses of the competitors.
54
Activities
Responsible body
Budget approved
Preparation of technical
specification and evaluation
Technical &Production
Management Office
Formal request
Technical &Production to
Commercial department
Commercial department
Release of Tender
Commercial department
Commercial department
Evaluation of tenders
Tender committee
Selection of suppliers
Tender Committee
Approval of supplier
General Manager
General Manager
Finance/Material Services
Receiving
Technical &Production
55
56
S/n
1
Evaluation criteria
Weight
given
Requirement
20%
Medium massecuite
5%
Capacity
50m3/hr
5%
Pressure
70 mtr head
5%
5%
Technical specification
25%
Manufacturer - well-known
4%
Pump type
- rotary pump
5%
Pump speed
- low speed
4%
4%
8%
Materials of construction
15%
PP casing - C.I
3%
Rotor bronze
3%
Shaft
2%
S.S
3%
2%
2%
57
Accessories
20%
5%
Insulation class F
5%
5%
5%
Other Factors
20%
5%
5%
Documentation
5%
5%
TOTAL
100%
58
59
60
61
Justifications of the capital budget requests shown in table 4.4 [see detail in appendix B] indicate
that the reasons given are 16.05 % due to obsolescence, 45.68% due to old age and 38.27% due to
other cases.
62
Obsolescence: In most cases the obsolescence observed are lack of spare part. True, this is one of
the reasons for obsolescence. The manufacturers might have developed a new design to replace
the existing machine and stopped to manufacture any part of the machine. The question arises is
the machine within the expected life economically? Most of the machines are beyond the
expected life so it is difficult to say that the mentioned 16.05 % of machines were replaced due to
obsolescence.
From the 16.05 % given some of the machines were requested for replacement
due to obsolescence and old age. In short, the obsolescence mentioned is more or less happened
to be at about the end of the technical life of the equipment.
Further, if the age of the machines is studied thoroughly most of them are aged enough. In other
words almost all of the machines might not become obsolete within estimated age but the
obsolescence came late after their expiration of their economic life. If the same machine is
required it is true that the equipment is obsolete (out of market). The unavailability arises due to
long service years, which is more than expected depreciation years so that even a very slow
technological development makes the equipment obsolete. Due to this it is difficult to say that the
equipment is changed due to obsolescence. It is better to say that replacement is initiated when
the technical life comes to an end or the machine becoming beyond repair.
Old age: About 45.68% of the justification given includes the machine are aged. If the machines
are aged either they are beyond repair or spares are manufactured with a special order or partly
within the organization. With these facts if there was a proper data handling system during the life
of a machine, it would have been possible to get the appropriate time when replacement will be
advantageous and state the exact reason for replacement.
63
Estimated capital budget: From the estimated annual budget requirement for replacement, shown
in table 4.5, it can be seen that the amount of money is not small. Including other annual capital
investment requests, which is not included in the study, is significantly high were assigning
manpower to deal with it is of advantage.
Reason of
replacement
Obsolescence
Old age
and long
service
years
To improve
capacity and
performance
Other reasons
(damage, loss in
accuracy,
Unreliability etc.)
Request
with
data
Without any
justification
Quantity
13
37
20
In %
16.05%
45.68%
24.69%
7.41%
1.23%
4.94%
Budget year
1996/7
1997/8
1999/2000
2000/2001
Estimated price
4,002,000.0
3,592,000.0
7,970,000.0
9,350,000.00
(Birr)
Metahara
10,009,000.00 AddisTyr
e
If spare is not manufactured at the original supplier, using reverse engineering it can be
manufactured somewhere else but at expensive cost. Some times the spares are manufactured in
64
the original manufacturer with especial order where the charge rate is increased if the supplier
have shifted product type.
From replacement proposals made on capital items the following facts can easily be identified on
request for equipment replacement.
Obsolescence of machines from the capital budget requests it can be shown that
obsolescence is due to long service years not due to technological shoot. It is a gradual
development nature. There is nothing eternal.
Most of the machines requested for replacement have completed their expected life. They are
at the least book value economically.
The data collected from industries mostly show that replacement is not based on a certain set
guide lines. It is based on the level of problem created by the machine. If the department or
the section responsible on the machine operation and maintenance believes to replace an
equipment it is not a simple task to get rid off it and bring another one. The first thing to get
approval to replace it, which is difficult due to poor historical data handling of the machine.
The level of discussion made is the indications that replacement is made not on data analysis
but on memory of individuals who are responsible and to some extent from data recorded for
the last years of operation. Another constraint for equipment replacement is capital. The
nature of capital allocation is more or less like rationing where the level of urgency dictates
equipment replacement.
65
The justifications given are of general nature due to which it is difficult to understand the
losses incurred or revenue decline by not replacing the machine or the revenue decline.
4.3.2 Challenger
The challenger is not computed with an existing machine but with other challengers. It is
mentioned on evaluation format that this equipment has got merit to assume this position. So,
1.
The evaluation method shown on table 4.1, tender document evaluation system, can be
questioned whether the evaluation criterion is complete or not. On the literature survey and
principles of replacement it is shown that the life of the equipment should be approximated
during selection. Even though the design aspect and the materials are mentioned the life
expectancy, life cycle cost or annual expense are not mentioned at all. For equipment in
operation replacement is made mostly due to obsolescence, operational interruption etc. but
the technical and financial evaluation criteria did not consider these basic assumptions for the
new equipment Even it can be said that the major part of the mathematical models and
formulas are directed towards this condition. On the contrary the tender evaluation system in
application does not give any attention to this issue.
2.
There are some cases where durability is mentioned but it is not in the sense of the principles
of replacement. That is there is no comparison method. Because of these reasons the
challenger assumed position will be the final. There is no method or way to check whether
appropriate equipment is bought or not if the problem, which was prevailing with the old
equipment, is solved some how.
66
3.
Every machine need some parts to be replaced on certain specified time depending on the
maintenance type, small, medium or overhauls that is the equipment need certain amount of
operating capital. The operating capital, which is very crucial, is not analyzed during the
tender evaluation phase.
One of the reasons of obsolescence is the development of new designs by the manufacturers
where spare manufacturing of the old ones will be stopped, so spare supply guarantee should be
considered in the evaluation criteria. If there is a guarantee period of supply of spares the rate of
replacement due to spare can be anticipated. In some of the evaluation criteria reputation of the
organization is rated. Yet this does not guarantee the supply time of spare parts.
Spare consumption can be found from material stores control cards. All spares are fetched by
filling request form and getting approval of the immediate technical boss and the chief of
technical personnel, and then requesting it at the store. So spare consumption are recorded but,
they are not in such a way that the consumption of each machine is separated. The parts, which
are not standard can be found easily from the spare part balance sheet in store. But standard items
can not be identified easily. Still there is another case where the spares are manufactured within
the industries. The manufacturing is made for two reasons.
1.
2.
For immediate use. The requests are made formally by preparing drawings or providing
samples and requesting on preparing logbook.
67
For both cases the data is registered in the workshop. The problem is to collect and record on a
way to show the statues of the machine.
4.3.4 Manpower
For every machine failure during operation requests are made for maintenance. The manpower is
assigned to do the work. After finishing the job operation resumes. From this the man-hour spent
to maintain the machine, the down time recorded due to this machine can easily be found.
Equipment data collection and analysis is very low. This can be expressed by the
justification given such as:
2.
defender
and the challenger. If it is possible to show the defender operating costs are very high then
68
the need to replace it would have been accepted but there is no way to compare the defender
and the challenger. On theory of replacement it is shown that there should be a comparison
system between the two. In actual practice the comparison is between different challengers.
3.
4.
The final purchase decision more or less falls under the principle of less initial cost
equipment.
From the above observations, an effort should be made to increase the level of confidence of the
technical personnel about the machines at their control and specifically pin point the condition of
machines in terms of money and vision on future performances. Efforts should also be directed to
improve data handling and manipulating system in a way that portray the status of the machine.
Due to lack of proper data collection and analysis the machines to be replaced may under go a
major built up (extensive maintenance).
Even though nowadays the problem of data collecting and analysis may not be a basic problem in
developed industries it is true that this problem is very crucial in our industries. This doesnt
mean that industries are working randomly. The important point to be given emphasis is that on
equipment replacement the series of meetings, the reasons given in capital budget request are
indications of not having sufficient data about the machine.
Therefore the thesis will focus on methods of data handling and analysis, as this is the
fundamental for taking appropriate decision. The other problems such as technological
69
advancement, shortage of capital, purchase analysis problem etc. can be considered as the
successors of data handling and analysis.
Chapter 5
70
COMPUTER BASED
SYSTEM DEVELOPMENT
5.1 GENERAL
The system is to be used as a template which can be adapted to any industry. It is developed as a
database management which is designed in Microsoft access. The reason of developing the
system using access is that:
71
It is simpler to use Microsoft access for some one who wants to use the system and
modify it to his need with small know how of the programming system,
Microsoft access is loaded almost in every computer so using the system will need no
special system.
The present situation on equipment replacement system is surfaced in chapter 4. From that,
information system is taken to be one of the major short-comings which do not go hand in hand
with policy of the equipment replacement. Then the question comes to how can the historical data
of equipment, that deteriorate gradually, be organized, and used to forecast on what to be done.
The equipment database is made to receive day to day data and synthesize the data to give results,
which is directed towards showing equipment expense versus time. Basically, it is using the
concept of LTCP discussed in chapter 3 section 3.7.2. The selection is made that the two
alternatives given in section 3.7.2 are specific while LTCP is more general to be used for any
equipment process type or not. It has the capacity to show the trend of future performance. At the
same time the policy mentioned in section 4.1 requires to show all about the equipment including
cost benefit analysis. So the proposed system is made to perform the following:
1.
2.
3.
72
4.
5.
6.
Sum up the maintenance cost to ownership cost to give total cost and generates a
graphs that show maintenance cost curve, ownership cost curve and total cost curve on
annual basis
Total annual cost = Running cost + Ownership cost
Where Running cost = Maintenance and operation cost
Maintenance and operation cost = Spare part consumption cost + Lubricant
consumption cost + Down time cost + Labor cost +
Loss of production due to down time + Other costs
Ownership cost
7.
To get the above results the management database system is designed as follows:
73
Equipment basic data: Include some basic features and data that describe the equipment
during installation as shown in table 5.1.
Operational data: All data's that are fed into the database after the equipment is in
operation such as maintenance and book value calculation as shown in table 5.2.
Depreciation: when a machine is bought the initial cost (ownership cost) is estimated to be
returned within a specified range of years or within estimated life of the machine. Based
on this estimated life, the annual depreciation is deducted from the ownership
74
75
76
Input data are made through forms. It is divided into the following
1.
Equipment basic data input: the input form is used to be tab-controlled to divide the datas
into convenient parts such as motor gearbox etc.
Operational data input: for simplicity and clarity the input forms to the operational
database are made through more than one form. Samples are shown below:
77
78
Equipment catalogue: Input to the equipment database is through units detail, parts
detail forms.
Depreciation data input: Raw data input to depreciation database is made through
depreciation data input form and depreciation sub form.
79
80
81
82
83
84
Identification system is one of the most important but laborious to institutionalize and make
familiar to the workers. In fact it is not new to state owned industries. They are using code system
which may or may not be convenient to computer system. Even it can be generalized that there is
no state owned industry working without code.
The codification used in this database is that recommended by consultants who have made audit
survey of Metahara sugar industry with small changes to make it uniform and simple in using in
computer system. The change made for all machines is that at the end of the code number a
quantity expression is added that is to identify equipments of similar type.
85
The example given 08 26 01 10/3 will be used even for equipments which do not have a stand
by or other similar units that is the suffix indicating number of installed units will be written even
for one unit.
Spare consumption can be found from material stores control cards. All spares are fetched by
filling request pad, after approving the immediate technical boss and further the chief of technical
personnel, then requesting it at the store. So, spare consumption are recorded but, they are not in
such a way that the consumption of each machine is separated. The parts, which are especially
required for individual machines, can be found easily from the spare part balance sheet in store.
But those, which are general, can not be identified easily.
Still there is another case where the spares are manufactured within the industries
The manufacturing is made for two reasons.
For immediate use. The requests are made formally by preparing drawings or
86
N
o
Date
Unit/Part
code
Voucher
No.
Qty
Unit Price
Remark
5.5.2 Manpower
For every machine failure during operation requests are made for maintenance. The manpower is
assigned to do the work. After finishing the maintenance job the operation resumes. From this the
man-hour spent to maintain the machine, the down time recorded due to this machine can easily
be found. It is more or less institutionalized. The following forms can be used as an input.
N
o
Employee Name
Employ
ee ID
Equipme
nt
Monthly
income
Man-Hrs
Remark
ID
5.5.3 Lubrication
Usually in industries there is a crew that follows the lubrication schedule of machines. Due to this
it is very simple to collect datas related to lubricant consumed for each machine.
87
Machine ID/Name
Date
Lubricant
Qty Refilled
Remark
Type
Machine
ID
Date
Production (Hours)
Interrup
ted
(hrs)
Resume
d (hrs)
Other
expense
Differenc
s
e
Remark
5.5.5 Depreciation
The depreciation system is taken to be a straight line depreciation as the present machinery
depreciation system in Ethiopia is straight line depreciation method.
Note:
All the data collection formats can be on one paper or separately depending on the
convenience of the organizational structure.
The formats are made as short as possible so that the responsible individuals will
not be bored.
Other materials such as fuel and power consumption, which may or may not differ
from machinery to machinery, can be considered in the system if required [15].
88
89
Chapter 6
Implementation Methods
6.1 Implementation
Implementation of equipment replacement system is part of industrial management and asset
tracking system where any organization should not bypass it. The importance of equipment
management should be one of the major issues in industries if expenses are to be reduced. The
seriousness can be guessed from the fact that in our computers, in Microsoft access one of the
templates presented is about equipment data handling under the heading of Asset tracking
mentioned in chapter three.
Equally whether there is computer system operation or not any organization strives to know the
day to day activities of each machine, employee etc. and makes analysis of expenses. In industries
visited, most of the important formats for data collecting are almost developed. But their
functionality is limited and data analysis concerning equipment replacement is very low.
The system developed can help to store data and provide detailed or summarized reports about the
machine expenses. So this is expected to be one of the major driving forces for acceptability of
the software from the users point of view.
90
For successful implementation and utilization of the software the following points cannot be
overlooked:
Individuals engaged in this area should understand the system, its advantage and be able
to modify it to their organizational need.
6.2 Justification
Beside the advantages mentioned in chapter 2 section 2.7.2.3 about LTCP, important points for
justifying implementation of the software are:
The awareness of coding system in industries, which may need a small change to be used
in computers,
The fierceness' of the market dictates management to reduce cost of operation or improve
operational methods,
The level of risk of failure is minimal and if there is any, the cost is not far-reaching.
There is no need to change existing system. It is with small adaptation that the system can
be implemented.
91
The naming of formats, the formats and any additional requirement of the organization
should be modified or included.
Supervisors and foremen should be given a brief understanding of the new system.
Prepare list of machinery with the codification and feed to the system category/plant.
The implementation should start from one category or plant then continue one after the
other. The first plant will be used as a pilot plant to the others.
Start routing activities collection such as down time, spare consumption etc. to the
category completed codification and feeding.
Weekly and monthly appraisal of the system and correction of errors and incorporation of
any important suggestions until it is well established.
The time limitation for implementation depends on how the existing system is favorable or
organized to adapt to the new system.
92
Chapter 7
The immediate and important future study areas related to this study are maintenance and
operational planning systems which are the major reliable data source to the system. Further
implementation can be one area of future work. As mentioned in chapter 6 changes and
adaptation to fit to individual industries is one part which need continued follow up and
correction.
93
7.2 Conclusion
The Equipment replacement system is one of the industrial problems for management. The
huge amount of annual capital investment needs concrete information for proper allocation
and utilization. The effect of replacement timing, selection, and method used for reaching
decisions are some of the important factors in the efficient operation and utilization of the
resource. Replacement decisions are more important in market oriented economy where
competition of the market is bringing profit margins to be minimal.
As indicated in chapter 3 most of the mathematical decision models are dependent on the past
performance of a machine. Thus, it shows that data collecting and analysis on equipment is
one of the important factors on replacement decisions. To get a realistic data about the
equipment proper maintenance management system, sensitiveness to cost variations through
the course of its life is vital.
It is believed that the study will give additional momentum to the industries and any interested
body who wants to keep track of his asset status.
94
Bibliography
1.
2.
Ackoff Russell L. Progress in Operations Research, New York: John Wiley and Sons
Inc., 1961.
Engineering
Economic Analysis, New York: John Wiley and Sons, Inc., 1977 pp. 169-182.
4.
Balcer Yves, and Sahin Izzet. 1986. Replacement costs under Warranty cost moments
and time variability, Opns. Res. 34, 554-559.
5.
6.
7.
95
8.
Carter, A.D.S. Mechanical Reliability Engineering, New York: John Wiley and sons,
Inc. 2nd ed., 1994.
9.
Daniel Kitaw. Industrial Management and Engineering Economy, Addis Ababa: Addis
Ababa University Printing Press,1994.
10.
Derman C., Lieberman G.j., and Ross S.M. 1983. On the use of replacement to extend
system life, Opns. Res. 32. 616-627.
11.
Farntahun Melaku,
Lecture Note on
Investment
Goldstein T., Ladany S.P., and Merhrez. 1986. A Dual Machine Replacement Model:
A note on planning horizon procedures for machine replacement, Opns. Res. 34, 938941.
14.
Grant, Eugene. Principles of Engineering Economy, New Delhi: Prentice Hall of India,
Inc, 5th ed. 1975.
15.
16.
J.C. Bonbright, Valuation of Property, New York: McGraw-Hill Book Co., Inc., 1937.
17.
Lewis, E.E., Introduction to Reliability Engineering, New York: John Wiley and Sons,
Inc., 2nd ed. 1994.
18.
96
Cambridge,
19.
Maynard, H.B., Maynard's Industrial Engineering Handbook, New York: McGrawHill, 1992.
20.
21.
22.
23.
Mustafi C.K. Operations Research: Methods and Practice, New Delhi: Wiley Eastern
Limited, 1993.
24.
Mukherji J.P. & Associates Pvt. Ltd. Technical Audit of Mtahara Sugar Industry.
1998.
25.
26.
27.
Orenstein, R , B., " Topic on the MAPI Formula," J. Ind. Eng., 7, 283-298
(1956).
28.
29.
Rao, R. Vithala, and Varaiya, P. Nikhil, A Balance Model for Evaluating Firms for
Acquisition s, Management Science, Vol. 37, no. 3, March 1994.
97
30.
31.
Terborgh, George. Dynamic Equipment policy, New York: McGraw-Hill Book Co.,
1949.
32.
Thuesen, H. G. and W.J. Fabrycky. Engineering Economy, New Delhi: Prentice Hall of
India, Inc, 5th ed., 1975.
Any part of it is not directly quoted in the thesis only the principles and ideas were
used.
98