Professional Documents
Culture Documents
Addenda to the 2007 Edition of the Code are issued in the form of replacement pages. Revisions, additions, or
deletions are incorporated directly into the affected pages. It is advisable, however, that all replaced pages be
retained for reference.
Replace or insert the pages listed. Changes given below are identified on the pages by a margin note, A09,
placed next to the affected area. Revisions to the 2007 Edition are indicated by 07 and revisions in the 2008
Addenda are indicated by A08. For the listing below, the Page references the affected area. A margin note, A09,
placed next to the heading indicates Location. Revisions are listed under Change.
The Record Numbers listed below are explained in more detail in List of Changes in Record Number Order
following the Summary of Changes.
--``,``,,,``,,`,`,`,```,``,,`,`,-`-`,,`,,`,`,,`---
Page
Location
xxv, xxvi
Foreword
Revised (06-343)
xxixxl
Roster
13
U-1
U-2(a)(5)
Added (08-90)
Table U-3
UG-4(a)
11, 12
UG-11
13
UG-14(b)
Revised (07-1493)
1416.1
UG-16(b)(2)
Revised (07-1220)
UG-20(a)
UG-21
19
UG-27(a)
30
UG-33(b)
33
UG-34(a)
4344.1
UG-37(h)
Added (05-1552)
UG-37(i)
UG-43(d)
Revised (07-473)
UG-43(e)
54
UG-45(b)(4)
70
UG-90(b)(16)
5153
(c)
Page
Location
7576.1
UG-101(a)
UG-101(b)
81
UG-115(b)
Revised (08-804)
84
UG-117(f)
8698.2
UG-120(a)(4)
Revised (07-1755)
UG-125(a)
UG-125(d)
Revised (07-262)
UG-127(a)
UG-127(b)
UG-129
(1)
(2)
(3)
(4)
(5)
Fig. UG-129.2
UG-130
Revised (01-059)
UG-131
UG-132
UG-134
UG-135(b)(2)
UG-136(a)(3)
Revised (05-421)
UG-136(a)(6)
Revised (05-421)
UG-136(c)(3)
UG-136(c)(4)(a)(1)
Revised (01-059)
102
UG-137(c)(3)
Revised (01-059)
104104.3
UG-138
Added (01-059)
106
UW-2(d)(3)
109
UW-11(b)
Revised (07-1623)
118
Fig. UW-13.3
99
100
120
Subparagraph
Subparagraph
Subparagraph
Subparagraph
Subparagraph
(01-059)
UW-16(b)
UW-16(c)(1)
Page
Location
125
Fig. UW-16.1
126, 126.1
UW-16(f)(3)
UW-16(f)(4)
Revised (08-574)
Fig. UW-21
Revised (07-1003)
UW-21
Revised (07-1003)
139
UW-40(f)(5)(b)
140
UW-46
UW-51(a)(3)
141, 142
UW-52(c)(2)
Revised (06-263)
159, 160
UCS-56(a)
165, 168.1
Table UCS-56
169
Table UCS-57
Revised (06-780)
173
Fig. UCS-66
189
Table UNF-23.2
190, 191
Table UNF-23.3
192
Table UNF-23.5
200
Table UHA-23
202, 203
Table UHA-23
204
Table UHA-32
233
UHT-34
252
Fig. ULW-18.1
262
ULT-2
ULT-5(b)
ULT-5(f)
ULT-17(d)
ULT-27
ULT-28(a)
ULT-29
264267
Table ULT-23
268
ULT-99(a)
269, 270
Table ULT-82
133134.1
263
(e)
Page
Location
271
ULT-99(c)
ULT-100(c)
272
ULT-115(a)(2)
274
Fig. UHX-3
280, 280.1
UHX-12.3
Fig. UHX-12.2
Added (08-30)
284
UHX-12.4(b)
Revised (08-30)
285288.1
UHX-12.5.9
Revised (08-30)
UHX-12.5.11
Revised (08-30)
UHX-13.3
Fig. UHX-13.1
UHX-13.5.6
UHX-13.5.7(b)
UHX-13.5.8
Revised (08-30)
Table UHX-13.1
Table UHX-13.2
UHX-13.5.10
UHX-13.5.11
Revised (07-127)
298
UHX-13.6.3
299
UHX-13.6.4(e)
UHX-13.7.3
300
UHX-13.8.4(g)
300.1, 300.2
UHX-14.3
304
UHX-14.4(a)
306, 307
UHX-14.5.8
Revised (08-30)
UHX-14.5.10
Revised (07-127)
UHX-16
Revised (06-1189)
UHX-17
Revised (06-1189)
Table UHX-17
326.1326.32
Part UIG
Added (98-403)
327, 328
1-2
Revised (07-600)
1-3
Revised (07-600)
333, 334
1-6
347
2-1(c)
Revised (08-806)
354
2-6
291293
297
309, 310
(f)
Page
Location
381
Mandatory Appendix
5
5-1(a)
Revised (06-1189)
5-1(e)
Revised (06-1189)
382
Fig. 5-1
Revised (06-1189)
383
5-5(f)
Revised (06-1189)
401
10-13(b)(3)
Revised (04-1666)
402
10-15(d)
441
13-17(f)(2)
458
Fig. 17-2
473
23-2(a)
Revised (08-384)
23-4(a)(4)
Mandatory Appendix
26
26-2
Fig. 26-1
26-4.1(h)
Added (06-1188)
500
26-14.1.1
502
26-14.2.1
503
26-14.2.2(q)
26-14.2.2(r)
26-14.3.1
504
26-14.3.2(g)
505
Table 26-15.2
515
30-2
525.4, 525.5
Mandatory Appendix
36
Added (98-403)
525.6, 525.7
Mandatory Appendix
37
Added (98-403)
525.8, 525.9
Mandatory Appendix
38
Added (98-403)
525.10, 525.11
Mandatory Appendix
39
Added (98-403)
525.12525.14
Mandatory Appendix
40
Added (98-403)
551552.1
L-1.6
L-2.1.2
483486
(g)
Page
Location
574
Fig. L-7.7.1
Revised (07-1192)
L-7.7.5
L-7.7.5(b)(1)
Revised (07-1192)
L-7.7.6
L-7.7.7
L-7.7.8
L-7.7.9(a)
581
Fig. L-9-1
582
L-9.2.2
585
L-9.5.1(a)
590, 591
M-4
Revised (01-059)
M-5.2
M-7
M-9
Revised (01-059)
595
M-12
Revised (01-059)
598
R-11
Added (06-780)
602
Nonmandatory
Appendix W
604
Form U-1
605
Form U-1A
605.1
Form U-1B
Added (98-403)
609
Form U-3
611
Table W-3
617
Form UV-1
618
Form UD-1
Revised (01-059)
619
Table W-3.2
633, 634
Nonmandatory
Appendix DD
663.10
Nonmandatory
Appendix MM
Added (98-403)
575576.1
593
--``,``,,,``,,`,`,`,```,``,,`,`,-`-`,,`,,`,`,,`---
NOTE:
Volume 59 of the Interpretations to Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code
follows the last page of this Addenda.
(h)
Change
97-289
Mandatory Appendix 30, 30-1 revised to state that the rules of U-2(g) shall apply when any of the geometric
limitations stated in 30-2(c)(1) and (c)(2) cannot be satisfied for a partially drilled hole.
New Part UIG added.
UG-125(a) Reference changed from UG-137 to UG-138.
UG-127 General revision.
UG-129 General revision.
UG-130 Code Symbol changed to Code Symbol Stamp.
UG-131 General revision.
UG-132 General revision.
UG-134(e) Tolerance format changed to agree with new UG-134(f).
UG-134(f) Pin device set pressure tolerance added.
UG-134(g) UG-134(f) renumbered.
UG-135(b)(2), footnote 62 The phrase various rupture disk devices changed to nonreclosing pressure
relief devices.
UG-136(a)(6) The term screwed changed to threaded.
UG-136(c)(3) Code Symbol changed to Code Symbol Stamp.
UG-136(c)(3)(d) Code Symbol changed to Code Symbol Stamp.
UG-136(c)(4)(a)(1) Code Symbol changed to Code Symbol Stamp.
UG-137(c)(3) Code Symbol changed to Code Symbol Stamp.
UG-138 Added.
Appendix M-4 Several references changed from safety devices/valves to the generic pressure relief
devices.
Appendix M-5.2, definition of valve failure controls The phrase of the purpose changed to for the
purpose.
Appendix M-7 General revision.
Appendix M-9 General revision.
Appendix M-12 General revision.
Form UD-1 General revision.
Form UV-1 General revision.
Appendix W, Table W-3.2 General revision.
UG-20(a) and UG-21 revised to include reference to U-2(a).
Table ULT-82 revised for SB-209-A95083 thickness values.
SA-1010 UNS S41003 Grades 40 and 50 added to Table UHA-23 and to Note (1) of Table UHA-32.
New requirement added in UG-101(a)(1) that production vessels or vessel parts that utilize the results of a
proof test shall also comply with all other applicable rules of this Division, along with the addition of considerations/guidelines to evaluate possible re-use of proof-tested construction based on previous editions of this
Division; Proof-Test Reports added to the 10-15(d) checklist, reference to Proof Test Reports and to
UG-101 added as appropriate, editorial revisions made to MDR Forms U-1 and U-1A to ensure proper documentation of proof tests.
SA-268 UNS S43036 material added to Tables UHA-23 and UHA-32 Note (1).
UG-136(a)(3) modified to clarify lifting lever requirements for water service over 140F.
SB-653 UNS R60702 added to Table UNF-23.5.
SF-467 and SF-467M N05500 added to Table UNF-23.3.
Requirements to the Code for split reinforcing pads for nozzles added by inserting a new subpara. (h) to
UG-37.
UW-52(c)(2) revised to clarify the acceptance criteria for spot radiography.
In the Foreword, the phrase and Guidelines for Acceptable Non-ASTM Editions inserted after the first
appearance of Guidelines of Acceptable ASTM Editions. The word ASTM deleted from all subsequent
occurrences of Acceptable ASTM Editions.
UCS-56 revised to change P-No. 5B Group 2 to P-No. 15E Group 1.
New R-11 added to Nonmandatory Appendix R describing preheat recommendations.
Mandatory Appendix 26 revised to limit the design temperature to a maximum of 800F and permit the use
of the operating temperature properties for the fatigue analysis.
(1) The phrase thick-walled expansion joints replaced by the phrase flanged and flued or flanged only
expansion joints.
98-403
01-059
--``,``,,,``,,`,`,`,```,``,,`,`,-`-`,,`,,`,`,,`---
02-4113
03-1733
04-311
04-1666
05-88
05-421
05-435
05-529
05-1552
06-263
06-343
06-780
06-1188
06-1189
(i)
06-1604
07-127
07-262
07-473
07-600
07-643
07-797
07-818
--``,``,,,``,,`,`,`,```,``,,`,`,-`-`,,`,,`,`,,`---
07-1003
07-1192
07-1220
07-1261
07-1416
07-1493
07-1499
07-1623
07-1755
08-11
08-30
08-79
08-90
08-306
08-384
08-432
08-574
08-743
08-804
08-806
08-999
08-1186
08-1187
08-1334
(2) The phrases bellows-type expansion joints, pressure vessel and heat exchanger expansion joints, and
thin-walled expansion joints replaced by bellows expansion joints.
(3) Where appropriate, the phrase expansion bellows replaced with expansion joint.
Table UHA-23 revised to add SA/JIS G4303.
The following formulas revised:
Ps formula in UHX-13.5.6
Shell membrane stress formula in UHX-13.5.10
Shell and channel membrane stress formula in UHX-13.5.11
Shell bending stress formula in UHX-13.5.11 and UHX-13.8.4
Shell and channel membrane stress formula in UHX-14.5.10
UG-125(d) revised by adding testing as part of the requirement for accessibility along with inspection,
replacement, and repair.
The thickness in the third sentence of UG-43(d) changed to minimum required thickness. The phrase metal
added to weld metal added per UW-42.
(1) UG-27(a) revised to permit the minimum wall thickness to be based on the formulas given in Mandatory
Appendix 1.
(2) Equations (1) and (2) revised for thick cylindrical shells in 1-2 of Mandatory Appendix 1.
(3) Equations (1) and (2) revised for thick spherical shells in 1-3 of Mandatory Appendix 1.
(4) Clauses provided that permit equations in Mandatory Appendices 1, 1-2, and 1-3 to be used in lieu of
existing minimum thickness rules of UG-27(c) and UG-27(d).
UW-16(f)(3)(a) revised to clarify that reinforcement calculations are not required for fittings covered by the
paragraph, if the vessel does not experience rapid fluctuations in pressure and meets the spacing limitations
of UG-36(c)(3)(c) and (d).
UW-16(f)(3)(b) revised to clarify that if reinforcement calculations are performed, material in the fitting
neck shall not be used for area of reinforcement.
Code Case 2484 incorporated for UNS N06035 to 800F (427C).
The word ANSI deleted from Part UG, Part UW, Part UCS, Part UHA, Part UCI, Part UCD, Mandatory
Appendix 2, and Nonmandatory Appendix L.
UW-21(b) revised to delete reference to Fig. 2-4, and new Fig. UW-21 added.
Example revised to include calculations at 0 deg and 90 deg to vessel longitudinal axis. Calculation of A2
corrected for plane 90 deg to vessel axis.
UG-16(b)(2) revised to define who is responsible to provide the protective shell, casing, or duct when not
provided by the Manufacturer, and cautionary note added about leakage into the compartment.
UW-16(b) and Fig. ULW-18 revised.
Required thickness in the concluding statement of example L-2.1.2 changed from 0.232 in. to 0.244. in.
UG-14(b) revised to permit wrought rod or bar other than rolled or forged.
ULT-2, 5, 27, 28, 29, 99, 100, 115, Table ULT-23, and Table ULT-82 revised to permit the use of materials
in Part ULT up to and including 150F (65C) rather than 100F (40C).
The introductory phrase of UW-11(b) revised to improve clarity.
UG-120(a)(4) revised to permit National Board Registration of UM-Stamped vessels and the contact information added for the National Board of Boiler and Pressure Vessel Inspectors.
A line in Form U-3 added for the National Board Number.
An X in Table W-3 added to show that Note (12) applies to Form U-3.
Errata correction. See Summary of Changes for details.
Part UHX revised for consistency with Section VIII, Division 2, 4.18.
Errata correction. See Summary of Changes for details.
U-1(k) deleted and moved to U-2(a)(5).
In UHX-13.5.10, Step 10, the stress limit 2Ss replaced by SPS,s.
New specification B-956 adopted as SB-956, and stress lines added for SB-956 C70600 and C71500.
UG-117(f) revised to clarify who must be involved in the third year review for UM Stamp issue.
The minimum fillet weld throat size changed to tc from 14 in. for Fig. UW-16.1 sketch (bb). Also, words
added in UW-16(f)(4) to describe the fillet weld size.
Errata correction. See Summary of Changes for details.
UG-115(b) revised to be consistent with U-4.
Mandatory Appendix 1, 1-6(d), 1-6(e), and Mandatory Appendix 2, 2-1(c) revised to allow using standard
flanges listed in Table U-3 without performing flange design calculations per Mandatory Appendix 2.
Clarification added to example shown in 13-17(f).
UG-1(b) and UG-4 revised.
Under item 2, U Code Symbol Stamp, numbers 4, 9, and 11 revised. A new number 9 added and numbers 9
through 12 changed to numbers 10 through 13. A new number 14 added.
Errata correction. See Summary of Changes for details.
(j)