Professional Documents
Culture Documents
SKF General Conditions for technical assistance and advice (available at www.skf.com) shall apply to this report.
SKF accepts no variation of any of these conditions unless confirmed in writing by SKF.
SKF is a registered trademark of the SKF Group.
SKF Group 2013
The contents of this publication are the copyright of SKF and may not be reproduced, duplicated, copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any
commercial use without the prior written approval of SKF.
Table of Contents
1.
Bearing Data
d
25.0 mm
47.0 mm
15 mm
27 kN
32.5 kN
1.1
Bearing life
Input Parameters
F
3 kN
12.5 kN
1000 r/min
Operating temperature
Bearing outer ring
40 C
r
Radial load
a
Axial load
i
Rotational speed of the inner ring
specification method
c
Cleanliness
classification(recommended)
Viscosity at 40 C
Viscosity at 100 C
Message
The given F (3 kN) is replaced by the induced F (34.9 kN) for checking bearing loading condition
r
r
Result
L
21 hour
0.37
10mh
SKF rating life
SKF
SKF life modification factor a
SKF
Viscosity ratio
2.01
P
Equivalent dynamic bearing load
18.7 kN
0.33
2
19.9 mm /s
57 hour
C/P
Load ratio
1.4
c
Factor for contamination level
1
Required kinematic viscosity for =1
10h
Basic rating life
1.2
Minimum load
Input Parameters
No user input is required.
Result
0.54 kN
rm
Minimum radial load
1.3
Input Parameters
F
3 kN
12.5 kN
1000 r/min
Operating temperature
Bearing outer ring
40 C
r
Radial load
a
Axial load
i
Rotational speed of the inner ring
Viscosity at 100 C
2
40 mm /s
2
6 mm /s
Lubrication
Grease
Viscosity at 40 C
Warning
The bearing load is high ( C/P=1.4 ). Please contact SKF Application Engineering.
Result
M
280.2 Nmm
131.1 Nmm
0 Nmm
0 Nmm
M
Total frictional moment
411.3 Nmm
rr
Rolling frictional moment
sl
Sliding frictional moment
seal
Frictional moment of the seals
drag
Frictional moment of drag losses
43 W
r
Power loss
2
40 mm /s
1507.2 Nmm
6.0E-8
start
Starting torque at 20-30C ambient and zero speed.
rs
Replenishment/starvation constant
1.4
Input Parameters
F
3 kN
12.5 kN
Viscosity at 40 C
2
40 mm /s
Lubrication
Grease
r
Radial load
a
Axial load
Result
f
0.2
0.2
p
Adjustment factor for bearing load P
v
Adjustment factor for grease base oil viscosity
tot
f f with grease lubrication
p v
n
ar
Adjusted reference speed with grease lubrication
1.5
2190 r/min
Relubrication intervals
Input Parameters
F
3 kN
12.5 kN
1000 r/min
Rotating ring
Shaft orientation
Horizontal shaft
Operating temperature
Bearing outer ring
40 C
r
Radial load
a
Axial load
i
Rotational speed of the inner ring
Error
The load 18.7 kN is too high to calculate a valid relubrication interval. Continous relubrication or oil bath
lubrication are recommended.
Result
t
??? hour
??? g
f
Relubrication interval
p
Grease quantity to be added when replenishing
1.6
Viscosity
Input Parameters
n
1000 r/min
Operating temperature
Bearing outer ring
40 C
i
Rotational speed of the inner ring
2
40 mm /s
2
6 mm /s
Viscosity at 40 C
Viscosity at 100 C
Result
2
40 mm /s
2
19.9 mm /s
2
19.9 mm /s
Viscosity ratio
2.01
1
Required viscosity at operating temperature for =1
ref
Required viscosity at 40 C for =1
1.7
Input Parameters
F
3 kN
12.5 kN
r
Radial load
a
Axial load
Result
P
Equivalent dynamic bearing load
18.7 kN