Professional Documents
Culture Documents
CDI SCHEMATIC
HOME
ABOUT ME
DOWNLOADS
MANUALS
PRIVACY
CDI
DISCLAIMER POLICY
Popular
Comments
Archives
ABOU
http://m
blogspo
my hob
VIEW MY
GOO
Nat
127 hav
circles
Getting deeper.
Materials needed.
1. full wave rectifier / regulator (known as R / R too many) like this Full wave regulator 5 wire
2. soldering iron at least 50-100watts
3. high temp insulator tube
4. OPTIONAL : New crankcase cover gasket (when returning the modified stator and placing the cover back to the engine)
5. A digital or analog multimeter (tester too many)
UPDATES BY EMAIL
IT is time to rock!!!
Email address...
Remove the left crankcase cover to gain access on the stator
what we trying to do here is getting the two end of the stator winding and removing the GROUND from the stator body as shown on the
illustration.
when done, first is first..check for continuity and resistance of the whole winding before returning back the cover to ensure everything done
is OK!!
Getting ready to wire the regulator from the modified generator
Submit
1. Green -- ground
2. Red
3. Yellow -- to charging coil (any of the two winding out from the stator)
4. Pink --- to charging coil (interchangeable with yellow)
5. Black --- To after ignition key switch
TESTING
To be sure and safe, for this test use appropriate FUSE within the positive line going to the battery. its the last line of defense when it
comes to possible wrong connection.
Disconnect all loads from the battery, if you have access to another way of supplying your CD ignition then do so..because we have to start
the engine to perform TEST. with the help of the multimeter set to DC voltage. tap it to the battery that is connected to the regulator..
GREEN to black probe
RED to red probe
check voltage....you are reading the battery voltage, on the ignition key and take a look at value, after turning on the key engine OFF, the
voltage must not be dropping and stay close to the initial reading.
kick the KICK starter, and stay it at idle, monitor the voltage. READING must now be moving up possible to 13 volts or 14 volts..(depends
on the condition of the battery)..
SLOWLY REV the engine while monitoring the voltage reading of the tester.....
as you are revving the engine..voltage must stay close to 15 volts not over 16 volts (overcharging threshold of lead acid battery)..
if all test performed are ok with regulator not to temperature....PUT a load on the battery such as your HID installed...then start the SAME
TEST again...
at first when you turn on the High intensity discharge system..at IDLE the voltage must not be dropping and will stay close to 12-13 volts..
if it is, then the system is already working..By looking at the graph above..FULL wave due to the better DC filtering, at idle or low rpm still
charging the battery unlike the HALF wave where in the dc is fluctuating.
Full wave also has a better shunting than half wave to the configuration of the rectifying diodes.
NOW u can enjoy your HID system, just make sure you are responsible enough to stoop down the beam for others. happy
motoring.
NOTE: since the lighting coil is disconnected and no longer used, all that was connected before will be redirected to the battery
being battery operated.
UPDATED
For the full schematic diagram of the regulator on this article, you can visit this link
FULL WAVE REGULATOR SCHEMATIC
VIDEO of this conversion. (many thanks to Thiago Ken Fuzita)
GT06 GPS
TRACKER
REVIEW
High Intensity
Discharged ballast
Testing Motorcycle
CDI Ignition Coil
Linkwithin
Newer Post
Download
Manuals
Home
Photo
125cc
Diagrams
Acid
Software Downloads
Download
Photo
Older Post
Contact
Diagrams
Generator
Videos
Software Downloads
135 comments:
Rey Broncano said...
I'm using a wave100, which i believe it has an AC CDI. If i will convert it to full wave R/R do I need to change the CDI
to DC?
May 14, 2014 at 7:57 PM
Nathaniel Berdan said...
you do not have to convert the ignition from ac to dc..just leave the High Voltage windings ground intact to that ground
slug of the generator, Charging coil and high voltage coil do share a common ground. Isolate the charging ground only
and float it or remove it from that ground tab...that's it.
May 14, 2014 at 10:23 PM
Rowell Tabieros said...
where i can find full wave rectifier...
May 15, 2014 at 11:03 AM
in my problem scr BT 151 they burn after 10 minutes riding. i'dont use the heatsink for this circuit ?
but this my schematic would you be correction for it ?
maybe you found right for ex ground or charging . im confuse about this .
check this "http://s6.postimg.org/o83ji4iqp/untitled.png"
thanks before. please post this image again for correction for positioning ex ground and charging coil ?
January 12, 2015 at 10:38 AM
Nathaniel Berdan said...
LedMazter, question? Did you modified your stator before making this circuit and put it on your Blade 110. Remember
that the regulator is for full wave converted stator, and not applicable to OEM or stock stator.
January 12, 2015 at 4:07 PM
LeD MasTeR said...
sorry for bothering again ? he he ...
for the detailed for my stator . the ground and email wire that connect to the ground of stator, i remove it with solder ,
then iam connect to the new wire go out what is connect to 2nd charging , 1st charging cable is white ?
but i leave the yellow one wire that connect to stator .
the new wire out from ex wire iam connect to the new regulator full wave . then why my scr is hot and bridge rectifier
hot to ?
maybe my problem is the tab lamp that connect to stator, but i leave it not connect anything... maybe that cause the scr
hot ?
thanks again nathan i appreciate your schematic .
i found new circuit for full wave regulator . check this
https://3.bp.blogspot.com/UIc0LPHs2CA/VGTdO51Q07I/AAAAAAAAFwg/EZ9htMMI7_U/s1600/sekema%2Bkiprok%2Bhonda%2Btiger.JPG
January 15, 2015 at 7:29 AM
Nathaniel Berdan said...
LedMazter, do not connect anything on Yellow wire or lighting coil wire..if you do then you are grounding the stator
back..
only 2 wire will be use.
The stator must not have any connection to ground...
(test the two wire that comes out of your stator with Resistance tester, connect positive probe to any of the two wire,
the negative to any metal of the engine. You should not get any reading..again NO VALUE)
January 15, 2015 at 11:06 PM
Nicholas Maspara said...
bro nathan pls help me . for XRM125 stock regulator wires are WHITE from stator/YELLOW to light/GREEN
ground/RED ignition sw. if i will use 5 wires regulator to convert it to fullwave what is the proper connection? pls need
your help.
thank you bro
January 21, 2015 at 5:56 PM
Nathaniel Berdan said...
Nicholas Maspara, you have to open the left crankcase to access the stator,
the green wire will be removed from the ground slug..(see this link http://mastercircuits.blogspot.com/2012/07/halfwave-to-full-wave-conversion.html)
(kailangang maalis ang ground winding sa stator kung san naka kunekta ang green wire..to make it a float ground..at
yung dulo ng winding na yon ka magdudugtong ng wire palabas..or. un solder the yellow wire at i kunekta sa winding
na inalis mo sa ground slug..)
yellow wire for lighting will not be used anymore para sa mga ilaw..lahat ng ilaw..kunektado na dapat sa baterya..
(battery operated na lahat)..
NOTE: if u are still confuse with the procedure, u can visit my garage anytime and will do it for you in less time)
January 21, 2015 at 8:32 PM
Nicholas Maspara said...
thank you bro but im here in bacolod city...what i mean is ,if im using a 5 wires R/R (red,black,yellow,orange,green) na
R/R ang green(ground) hindi na magagamit? kasi tatangalin natin ang ground sa stator connect natin sa dulo ng
winding? tama ba bro? kasi apat lang na wire came out from the stator while we using a 5 wires R/R .
gusto ko nang mag convert naka HID ako need your help, thanks
January 23, 2015 at 6:38 AM
Nathaniel Berdan said...
Just for you..TATAGALUGIN ko..
ang kulay ng RR mo na limang wire ay
red
black
yellow
pink or orange
green
red ay to positive ng baterya
black ay sa ignition switch mo (after the ON state or yung kuneksyon na pag nag bukas ka ng ignition mo ikakabit)
yellow ay sa stator na DINUKTOR
pink or orange ay sa stator din..(yellow at pink pwedeng kahit san sa stator)
at green ay ground..ground ng baterya..or ground ng buong bakal ng motor mo.
malilito ka kase inuuna mo ang regulator..wala ka papakialaman dyan..sa stator ka mag concentrate. ngayon..alam ko
nalilito ka sa stator mo kung paano mo aalisin ang grong nung winding...
IHIHIWALAY mo yon sa bakal ng stator at iaangat at dudugtungan mo ng wire palabas..na sya mong magsisilbing
kabitan nung pink or yellow wire ng RR...(clear na ba..o hindi pa)
January 23, 2015 at 11:38 PM
Nathaniel Berdan said...
To make CLEAR things here..once you did not float the ground connection of the winding from the stator ground tab
SOMETHING WILL GO TO SMOKE!!!!
be sure you are aware of what you are doing for this modification is simply not for NAGMAMARUNONG lang..have a
qualified electrician with you..NEWBIES...Thank you very much!!!
i am not responsible for any damage you have done in case you did it wrongly.
January 23, 2015 at 11:42 PM
Zandro Narvaza said...
Sir tanong lang sana ako if di ba to nakakaovercharge ng battery, napapansin ko na at low revs (di ako speed freak) di
nahahabol ng charge lalong humihina ang battery
January 24, 2015 at 3:30 AM
Nicholas Maspara said...
got it bro, thanks nalilito ako sa regulator kasi ang stock 4 wires , 5 ang ipapalit ..
thanks bro thanks.
January 24, 2015 at 5:26 AM
Nicholas Maspara said...
gawa na bro thanks ganda ....request kita sa fb by motomaniac
January 24, 2015 at 8:24 AM
Matias Borquez-Pratx said...
Hello,
I need to Update my Stator 6 Poles AC to Full wave DC) from my Vespa S 50 2007.
I have Many wires :-(
Yellow
Blue
Green
Grey
White
Red ( external with generator coil)
How to Update this stator in Full Wave DC ?
Thank you
Matias
January 24, 2015 at 8:03 PM
Nathaniel Berdan said...
Hi Matias, is your S 50 vespa 2 stroke, i am not actually familiar with italian scoots, but nonetheless i am trying to look
for at least a visual photo of your stator all thru the internet.
January 25, 2015 at 3:32 AM
Matias Borquez-Pratx said...
Hello Nathaniel,
Thank you very much for your reply and your HELP !
Normally for Full wave DC i need 5 wires : 2 yellow + White + Red + Green.. that's Right ?
Please see this 3 pictures of the REAL stator of my Vespa S 50.
http://s02.epstatic.nl/partpics/0118180310D_zoom.jpg
http://www.sip-scootershop.com/wwimages/3c0c57bb-8878-42a0-9630-3c82c5a5bcfe.jpg
http://www.sip-scootershop.com/wwimages/12d5e906-7195-4fa2-833a-ce14d243f371.jpg
Maybe you a little solution for me ... ?
Thank you again.
Matias
January 25, 2015 at 10:21 AM
Matias Borquez-Pratx said...
i send to you the wiring diagram of the Vespa
http://pscgroup.square7.ch/Manuals/Piaggio%20X/circuits/ET2%20later%20model.jpg
And the new Regulator/Rectifier Podtronics FULL DC BGM6698 (This remplace the older)
http://www.scooter-center.com/en/product/BGM6698
Thank you :-)
January 25, 2015 at 10:26 AM
Nathaniel Berdan said...
hello again sir Matias, first analysis, indeed you have 6 wires coming out from the stator area.
red--this is the wire from the pick up coil, leave it intact.
white--this is your high voltage exciter coil for your ignition and definitely your cdi is an AC-CDI.
From the wiring diagram, hopefully it is intended for your vespa and what was written there goes to such item.
you have an oil check device installed on your regulator as well as the flasher unit for your signal light, so the stock
regulator will remain, but then the other 4 color wires left is what make me very confuse.
Matias, is it possible to check with a Continuity tester between pin 1 and pin 2 (both gray color wire on the regulator if
they are connected) pin 2 goes to your lighting..this wire will be omitted after the conversion.
the BLUE wire is what really make my head blown away, why in the world an AC is connected directly to your on board
BATTERY?..
Can you kindly check the wire that is connected to the ground tab..(body ground of the stator? before we proceed.
Thank you very much.
January 25, 2015 at 3:39 PM
Matias Borquez-Pratx said...
Hello Nathaniel,
Thank you again .. so sorry i'm NEWBIE ! :-( :-( .. and sorry for my english)
SO ... See this new picture (Take in the manual Vespa S) You have all Colors wires for each connector
http://nsa33.casimages.com/img/2015/01/26/150126010542687526.jpg
- In the middle image (MAGNETO FLYWHEEL CONNECTOR) the number 4 the color wire is GREY (NOT YELLOWBLUE)
- The Ground in the Vespa Touch the chassis... The Ground in the stator is (i believe) in the body of the stator plate.
Thank you
Matias
January 25, 2015 at 4:28 PM
Matias Borquez-Pratx said...
probably this picture helps you
http://nsa33.casimages.com/img/2015/01/23/150123034854874276.png
Tnx
January 25, 2015 at 4:33 PM
Nathaniel Berdan said...
Hi again Sir Matias,
sorry for the late reply. Your vespa stator seems to have a common ground on all of the windings there, and may not
be able to convert it for full wave, and at this time I am no help to you. I am trying to isolate the charging coil via all of
your photo link attachment but it seems visualization is not enough. I need to have to get a hands-on job for a vespa
stator to help you. So sorry mate.
January 26, 2015 at 3:37 PM
jayson john sagorio said...
thank it work for my raider j110. now i am satisfied with the charging,,..
January 26, 2015 at 3:38 PM
Matias Borquez-Pratx said...
Thank you for your reply :-)
If this is not possible ... I'll connect the HID from the battery.
Last little question ... (for last solution)
Exists a solution in my AC Circuit to have a smooth lights (Ultra Bright) in Headlight and Tail Light, instrumental panel
and turn signal? (To have the same voltage in all lights all the time)
Because all the lights of the Vespa is not so bright When The bike running at low speed.
Matias
January 26, 2015 at 4:07 PM
Mark Ian Lim said...
Good day mr nathaniel
I ask If possible the fullwave to mio sporty amore?and if possible and already install . I ask if the battery will not over
charge because if day time no lights will use.. thank you
January 26, 2015 at 11:35 PM
Stavros Bxs said...
Hello i have a honda wave125i efi,can i do this fullwave?and do i have to buy something?
Thank you very much
January 27, 2015 at 9:20 AM
Nathaniel Berdan said...
Good day to all of you.
Sir Matias, your headlight, turn signal, instrument and tail lights all are powered by different AC coming out from the
stator, and will only be bright when the vespa is at revs. If we are unable to convert it to full wave like the way I see it
visually, redirecting all of those lights to the battery and adding HID to the system will surely just discharge it faster
creating serious problem. if only Sir you are in my country, I will definitely will try to convert it personally for your needs
Mark Ian Lim if you will just follow what is written within the article of all the procedure with the testing after the
conversion is done. It will not overcharge the battery.
Stabros bxs Did I saw EFI? we all know EFI needs a clean DC for it to function normally, and that is 3 phase full
wave, Honda wave EFI as far as I have known was already using the 11 pole stator in a 3 phase manner so no need to
downgrade it to full wave single phase.
one end of the windings is connected to the metal body of the stator.
Estregan good day to you sir, your motorcycle is an AC-CDI with external high voltage exciter coil..the green wire
represents it. The black wire is your ground, you have to open the stator side and access the windings.One end of that
winding is connected near that black wire and you need to desolder it leaving the black wire connected to the solder
lug. After that you have to either extend the removed winding with a WIRE o the outside of the crankcase..You'll have
then the BLUE wire plus the wire you placed outside as the TWO WIRE for the full wave regulator..(your existing
regulator will be discarded and be replaced by a 4 WIRE full wave regulator)
January 29, 2015 at 6:35 PM
estregan said...
Yes, got your instructions and pretty much know what to with the stator windings.
What i want to know is how do i connect my purchased 5 pin regulator /rectifier. Thanks
January 29, 2015 at 8:31 PM
Nathaniel Berdan said...
Estregan here is the link if the full wave you purchase represents the same color of wire
http://4.bp.blogspot.com/vmYlXBxXYNc/UBdeR8apb_I/AAAAAAAAA3w/CmXoh9ci6ek/s1600/Full+Wave+Regulator+schematic+2.jpg
January 29, 2015 at 10:40 PM
estregan said...
Hi Nathaniel, I already saw the diagram. However, I am not sure how to apply it to the diagram of my scooter. Could
you please tell me which color wire from the rr connects to which color wire in my diagram?
Thanks!
January 30, 2015 at 2:38 AM
Nathaniel Berdan said...
Estregan hello again sir, after completing the removal of the ground winding and putting a wire that goes outside..
check this link.
https://www.dropbox.com/s/gmzc4jfevg47eih/connection.jpg?dl=0
Thank you.
January 30, 2015 at 4:31 AM
estregan said...
Thanks, this confirms how i plan to do it. Will report back what happens after i try it.
January 30, 2015 at 8:09 AM
subcode said...
@nathaniel
hello po.. ahm, meron po bang other way na ma full wave using the full wave r/r without modifyng the stator coil?
February 6, 2015 at 4:45 AM
Adrian Borboran said...
sir tga nathaniel pwede po b ako mg pa fullwave sayu ng raider ko my hid projector kasi ako ts tinggl ko sxa ksi lks
mlwbat panu ko po kyu mcocontact para mkpg pgwa ako sa inyo
February 6, 2015 at 6:29 AM
Nathaniel Berdan said...
subcode there is no other way..u have to open that left side crankcase..(pag hindi mo tinanggal ang ground nung
winding, grounded pa din ang stator, pag nag ikaw ay nag full wave...walang winding na nakadikit san man sa body
ground..)
Adrian email me your contact number, click ABOUT above and select CONTACT ME
Please do not leave any number here thank you.
February 6, 2015 at 4:20 PM
subcode said...
@nathaniel
ahh ganun po ba. kasi po sa pag kakaintindi ko sa diagram above, yung yellow wire eh dun din kinonek sa ground taz
pinutol lng yung ground. so yung idea ko eh putulin ko nlng yung lahat nang ground wire na connected sa chassis den
yung yellow wire ehh putil din at i connect sa chassis.. paki explain po kung hindi pwede idea ko po.. thanks..
February 6, 2015 at 4:36 PM
Nathaniel Berdan said...
subcode ang half wave system...grounded ang isang dulo ng winding..sa madaling salita, yun na ang pinaka ground
mo..
sa full wave naman walang anumang dulo ng winding ang kunektado sa ground..ang ground ay mang gagaling na sa
regulator mo.
ang yellow wire ay ilustrasyon lamang na pwede mo gamiting wire kung ayaw mo mag dagdag pa ng wire dahil sa full
wave useless na ang yellow wire at wala na ito pwedeng KABITAN..
doing so...may UUSOK surebol yon..
alam ko ang iniisip mo...kukunin mo ang yellow at di mo aalisin ang ground..TRY mo..hanap ka nga lang ng FIRE
EXTINGUISHER..dahil di ako liable sa pagusok o pag apoy ng motor mo
February 7, 2015 at 6:03 PM
Homer H. Camposo, Jr. said...
Sir Nathaniel, if mag convert po ng full wave para pang charging lang at hindi naka HID diba advise nyo is e convert
ang stator driven headlight and tail light to battery source. Ok lang po ba kung mag higher wattage ako ng headlight
like 55 or 60 watts instead na 35 watts lang? kakayanin po ba ng system. need ko din ba mag change ng higher amp
na battery, mga ilang amp kya ang pwede? TIA.
February 8, 2015 at 7:09 PM
Nathaniel Berdan said...
Homer converting to full wave does not mean mainly for the purpose of High Intensity Discharge lighting system fitted
in a motorcycle. It can also be applicable to thise who just need an extra boost on charging during engine idle. We all
know when the conversion is done, all lights will be directly driven by your battery, and thus will add additional load in
it. Just make sure the outgoing current being thrown by the battery on those lights will not be less than the current
thrown in by the conversion of the entire charging system, Use AMMETER to check and for the process of how to
connect, feel free to use the ALL FREE GOOGLE SEARCH.
February 9, 2015 at 4:04 PM
Nathan Liwanag said...
good day sir, i convert a honda wave 125 from my friend ,i follow everything but something go wrong all wire get
melted ,i'm wondering about it's stator coil, the resistance is twice as my wave 100 it reads around 2.5 ohms is that ok
sir ,i already converted the stator to fullwave and i use a 5wire rectifier,thank you in advance sir for giving a comment,
seanlight23@gmail.com
February 15, 2015 at 6:46 PM
Nathaniel Berdan said...
Nathan i am sure your purchased regulator is FAKE, that is why all wire got melted.
February 17, 2015 at 6:18 PM
Marc Hubert de Guzman said...
gudpm sir!
is this applicable to yamaha mio MX125??
February 22, 2015 at 7:58 AM
Nicholas Maspara said...
gudpm nath, using an ohm meter , how do we know (test) that the RR is fake or not?
any testing procedure for the RR before we buy?
thank you very much
February 22, 2015 at 9:18 AM
estregan said...
Hi, just want to report back that my full wave conversion for my LML was successfull, thanks to Nathan for being very
helpful. Cheers!
February 22, 2015 at 6:15 PM
Na Na said...
Sir, NEED HELP!!
I have honda scoopy classic scooter(carbutetor, not eletronic fuel injected). I DIY installed 4 hi-LED foglamps , 6 LED
underglows, Tri-LED headlight, LED light instruments, hi-LED parking & brake lights, and third LED parking & parking
lights in the givi box... I also replaced the horn to a more classic tone.
ISSUE: Whenever I turned on all lights, horn is weak and even stops working. Its working fine if fog lamps and
headlight are turned off. Im really confused due to all lights are LED and have low wattages. All LED lights arent dim if
all turned on, only the horn weakens or stops. All systems are converted to battery driven. Is the ampere of my battery
not enough? What shall I do?
Some adviced me to get a so called "fast charger"... Others told me to remove or disconnect a certain wire in the
rectifier/regulator to gain faster recharging(is this true? )... I dont know how, Im no mechanic nor a technician, just
know the basics.
Anyone, please HELP!
**Im from Cebu City, Philippines by the way. 09154410517
_
March 10, 2015 at 7:04 PM
chino said...
Good day sir! Is there a possible way to convert raider 150 into a 3-phase full wave system? Tnx and more power!
09334059722
April 24, 2015 at 4:24 PM
Nathaniel Berdan said...
Na Na Is your charging system still at the stock or original configuration? If YES, then there is your answer to the
problem. Kindly read all possible article on this site about motorcycle charging.
chino possible but what is your primarily intention? Full waving the raider r150 is enough that is if you are planning or
have plans on converting your entire ignition to EFI system then the 3 phase system is mandatory..
April 26, 2015 at 9:36 PM
chino said...
Good day Sir Nathan. Ask ko lang po, after getting the two ends of the stator ( which is the ex-ground and the original
charging coil), does the center tab can still be used for additional charging purposes? If so, does it require a certain
type of R/R? Tnx. 4 reply!
April 28, 2015 at 8:55 PM
Nathaniel Berdan said...
chino the answer is NO, since you omitted the ground, center tap which is the yellow wire is already unusable.
April 28, 2015 at 11:00 PM
Roy said...
good day sir nath! plano ko rin pong i-full wave ang kawasaki fury ko. mukhang madali lang naman yung sa stator, so
ang question ko nalang po ay kung paano malalaman kung full wave o half wave ang R/R? pag 5 wires ba yung R/R
sure na full wave sya? yun rusi na motor ng kaibigan ko 5 wires yung stock R/R nya. yun nalang gagayahin kong
model ng R/R kung sure na full wave sya.
April 29, 2015 at 5:44 PM
Nathaniel Berdan said...
just ask for a full wave regulator 5 pin at your nearby local shop. If they do not know that then the shop is not selling
any.
FYI, there is no such thing as "madali" for even us who built and sell full wave regulator do mistake for not all stator are
not created equal thus every motor have different regulator.
May 1, 2015 at 8:28 AM
Roy said...
hindi naman po sa pagmamayabang kung sinabi kong mukhang madali. pinanood ko po yung posted video nyo at
kinilatis ko na rin po kasi yung wirings ng stator ko. kahit papano rin po ay marunong naman po ako sa electricals kaya
ko nasabi yun. but anyway salamat po sa paalala. pag hindi na limited budget ko gagawin ko tong guide nyo.
salamat po sa tutorials na ito sir!
May 2, 2015 at 4:48 AM
Roy said...
This comment has been removed by the author.
May 2, 2015 at 12:03 PM
Roy said...
good day again sir nath! may itatanong pa po pala ako. kasi di po ba center tap ang stator dito sa tutorial nyo? 1 line
for charging, center as body ground and last line for headlight. what if lagyan pareho ng diode yung line 1 and 3 then
yun ang papuntang stock half wave rectifier? half wave line 1 + half wave line 2 = full wave. click here for the image
May 2, 2015 at 12:06 PM
Nathaniel Berdan said...
roy do not be mistaken with the full wave (2 diode) vs full wave bridge (4 diodes)..I know what you are thinking right
now in lieu of that center tap winding.
As far as i know, you cannot use the existing stator winding for full wave in either 2 diodes or full bridge unless you
float the last end of the winding that is connected to ground..
I never experimented with the 2 diode full wave using the center tap as ground, for i have not seen any circuit with 2
Thyristor connected to the windings of the stator for clamping...
If you have any circuit available, why not share it here..for there are too many visitors all over the world, not only in the
Philippines but worldwide viewing this..
The site is not a forum like MCP, but you can post everything you have in mind for others to see, as you do.
Thank you.
May 4, 2015 at 7:03 AM
romelito Libaton said...
Ano color po ba ang dapat tanggalin sa regulator sucket pra mag fastcharging po...suzuki smash 115 at 3LED po ang
motor ko...
May 27, 2015 at 3:55 AM
Roy said...
paps Nath, may nabili akong 5-wire recifier/regulator. color coded naman yung mga wires maliban sa black. as per
your post is black pero yung sa akin is red na may white line. bale red, green, yellow, pink tapos yung 5th wire is red
with white line. ask ko lang kung full wave ba itong nabili ko? hindi alam nung pinagbilhan ko pero dahil nga sa 5 wires
and tama naman color code nung 4 wires kaya sumugal na akong bilhin kahit di ako siguradong full wave. chaka last
na tanong na, pwedeng patulong kung may idea ka sa wiring diagram ng stock rectifier ng kawasaki fury kung what
wire goes where? tia!
May 31, 2015 at 1:14 AM
Roy said...
This comment has been removed by the author.
June 9, 2015 at 2:43 AM
Roy said...
This comment has been removed by the author.
June 9, 2015 at 2:43 AM
subcode said...
sir, yung rectifier na nasa picture, ganyan din ang stock rectifier nang mga 110 unit nang mga rusi. full wave rectifier
kaya? tsaka ang stator nila na 6 poles, instead 4 wires, 5 wires sya at green ang ikalimang wire na nka kabit sa
ground. so meaning, pag pinutol ko yun, wla nang bodyground at possible ko ma fullwave ang charging system ko
without modifyng the stator itself.. sa tingin nyo po sir? tama kaya na isip ko?
June 18, 2015 at 10:41 PM
ezekiel herras said...
sir m.circuit ask ko lang po panu po pagconvert ng headlights to dc, ang ginawa ko po kc inalis ko na xa sa yelow wire
from stator the i tap it to black wire w/c is acc pero pang pinaandar ko c mc sa stator parin galing ung power kc
pgnagmenor humina din ung lights..help me nman po panu ko iconvert sa batt ang lights ko..tnx po and more power
master.
June 28, 2015 at 10:52 PM
ezekiel herras said...
sir nathaniel ask ko lang din po, bakit po ung battery ng mc ko pag-inalis ko ung wire sa positive then test ko siya with
multimeter para sa continuity tap ko ung lead sa wire na positive then tap ko sa body ng mc ala continuity pero pag
kinabit ko na sa batt ung wire, may continuity na nag beep na ung multimeter. anu po ibig sabihin nun? tnx po sa sagot
June 29, 2015 at 1:24 AM
Joseph Martin said...
How to test a regulator rectifier ?
July 27, 2015 at 11:22 PM
Ian Ray Lagundino said...
sir nathaniel, xrm 125 po ung motor ko, nka hid projector 6000k po ang headlight at may mga LED lights po ako sa
front na malalaki, pinagawa ko po ung charging system ko sa electrician samin pinalitan nya yong stock na regulator
ng XRM ko sa 5-wire regulator na binili ko sa shop, kaso ngkakaproblema po kasi one time ng overheat yong battery
ko at nasira. pinalitan namin yong batery at saka linagyan nya po ng switch connected to regulator na kung gagamit
ako ng headlight ko i-on ko yong switch.. kaso po kapag hindi naka on yong switch ko bumabagsak yong charge ng
battery ko(11.9 hanggang 11.5v). ano po sa tingin nyo ang problema po? salamat po..
August 17, 2015 at 5:58 PM
Andria BZ said...
Thanks for this post; Battery is the only source that assists to prevent us from the power demanding time, so choice of
your battery should give at least minimum power consumption so better to buy your batteries from the battery
authorized dealers
Regards,
Battery dealers in chennai
August 18, 2015 at 4:19 AM
Patrick Mendoza said...
How to fast charges
Meron wire na color white/yellow mula sa stator
Putulin mo un
Then ung yellow/white na isang side (hndi ung galing sa stator) ay itap mo sa color orange (ignition wire un)
Then ung wire n galing sa stator eh itape mo nlng...
Yan ung first trick
Nagets mo po ba bossing?
May nagsabi lang po sakin sir, nag check din ako ng 3 skydrive na naka fast charge at yan din nakita q.. Tama po ba
yan bossing? Kahit hindi na palitan ang R/R?
October 6, 2015 at 6:31 PM
RAM Bow said...
sir nathaniel,
nagawa kona ang fullwave conversion sa stator. bago ko ginawa ito kumakarga pa ang bateri sa pamamagitan ng
dissconnected ang yellow wire.
after ko magawa fullwave pati nadin ang fast charge rectifier. parang inuubos ang karga ng baterya. nakikita ko sa volt
meter kumakarga next day walang karga ang bateri ?
ang koneksyon sa rectifier sa 5 wires sinundan ko ang stock wires nito at ang black wire sa ignition. thanks
October 12, 2015 at 9:27 PM
Nathaniel Berdan said...
I guess you did something wrong. Again, as i have been telling all of you before. Not a job of beginners. Check again
and make sure your regulator is not a FAKE one.
October 14, 2015 at 11:13 PM
toto balasote said...
Sir tanong ko lang po kung papano iconvert sa full wave ang suzuki smash 110? ganun din po ba ang gagawin yong
kagaya sa video nyo sa youtube? magpapalit din po ba ng rectifier/regulator? Salamat po.
October 19, 2015 at 10:51 AM
toto balasote said...
Sir tanong ko lang po kung papano iconvert sa full wave ang suzuki smash 110? ganun din po ba ang gagawin yong
kagaya sa video nyo sa youtube? magpapalit din po ba ng rectifier/regulator? Salamat po.
October 19, 2015 at 10:51 AM
Roy said...
This comment has been removed by the author.
October 30, 2015 at 7:56 AM
gina said...
Sir good day sayo (NEWBIE HERE). How about my sniper mx 135, can i apply this fullwave rectifier/regulator? Does
my MX single phase or 3-phase? i've got DC-CDI hindi po ba masisira eto if i converted to fullwave? What is the first
thing to do? Soory sa dami ng tanong po....gusto ko lng po matuto then apply it to my MX. Salamat po ng marami.....
November 21, 2015 at 6:07 PM
dane llorera said...
sir san po ba ang shop or garage nyo? baka pwedeng makabisita at makapag pa full wave.. motor ko pala is honda
wave 100r.. pde din po ba makuha number nyo sir? salamat po and waiting for your reply..
December 30, 2015 at 8:12 AM
dane llorera said...
sir san po ang shop or garage nyo? baka makabisita at maka pag pa full wave.. honda wave 100r po ang motor ko..
December 30, 2015 at 8:22 AM
dane llorera said...
This comment has been removed by the author.
December 30, 2015 at 8:22 AM
chad plaza said...
sir sa mio smiley sir?? ganun lng din ba ang process na gawun sir?? thanks
January 25, 2016 at 7:24 PM
chad plaza said...
sir sa mio smiley sir?? ganun lng din ba ang process na gawun sir?? thanks
January 25, 2016 at 7:24 PM
Ryan Datiles said...
sir napanuod ko ung video nyo, ask ko lng po papaano naman po kung hnd ko gagamitin ung tredled ko o HID. ung
sobrang volts, sa battery hnd kaya lumobo ung battery ko?
May 21, 2016 at 9:01 PM
Ryan Datiles said...
sir napanuod ko ung video nyo, ask ko lng po papaano naman po kung hnd ko gagamitin ung tredled ko o HID. ung
sobrang volts, sa battery hnd kaya lumobo ung battery ko?
May 21, 2016 at 9:01 PM
Joseph Martin said...
SIR NAKA CONVERT NA YUNG SCOOTER KO SA FULL WAVE KAPAG NASA IDLE STATE CIA IS 13.8V,AT KAPAG
NAKA HIGH REV CIA HANGGANG 14.7V....ang tanong ko sir is ang brushless waterpump ba na dc motor na 12v
hindi kaagad masisira since 12v lang ito.....?
July 22, 2016 at 4:40 PM
Lucas said...
telasmosquiteira-sp.com.br
telas mosquiteira
telas mosquiteiro
As telas mosquiteira sp , telas mosquiteiro sp garantem ar puro por toda casa livrando-a completamente dos
mosquitos e insetos indesejveis. As telas mosquiteira garantem um sono tranquilo a toda famlia, livrando e
protegendo-nas dos mais diversos insetos. Muitos destes insetos so transmissores de doenas e a tela mosquiteira
indispensvel no combate a mosquitos transmissores de doenas.
A dengue, por exemplo, j matou centenas de pessoas s na capital de So Paulo e um pequeno investimento em
nossas telas mosquiteiras podem salvar vidas. As telas mosquiteiras tambm impedem a entrada de insetos
peonhentos como as aranhas e os escorpies, estes insetos tambm oferecem risco, pois seu veneno em poucos
minutos podem levar uma criana a morte.
telas mosquiteira jundiai
telas mosquiteiro jundiai
telas mosquiteira aplhaville
telas mosquiteiro alphaville
telas mosquiteira granja viana
telas mosquiteiro granja vinana
telas mosquiteira cotia
telas mosquiteiro cotia
telas mosquiteira tambore
telas mosquiteiro tambore
A chegada da temporada Primavera/Vero traz consigo a elevao da temperatura e a maior ocorrncia de chuvas.
Mas no s isso. As estaes mais quentes do ano causam muita dor de cabea e muitos zumbidos indesejveis
em funo das pragas urbanas pernilongos, baratas, cupins e outros insetos -, que afetam todas as regies
brasileiras.
Nossa misso oferecer telas mosquiteiras de qualidade a um preo acessvel, fazendo com que as telas
mosquiteiras sejam uma opo vivel para muitas pessoas.
telas mosquiteiras Jundia
telas mosquiteiro Jundiai
telas mosquiteiras jundiai
telas mosquiteiro industria
telas mosquiteira restaurante
telas mosquiteiro restaurante
telas mosquiteira empresa
telas mosquiteiro empresa
August 15, 2016 at 10:45 AM
Raymond Ocampo said...
hi sir panu po mag fullwave sa xrm 110?
kasi mejo alanganin ako gawen although kaya naman
the problem is pag dating na sa r/r wirings di ko masyado kabisado
August 17, 2016 at 9:14 PM
Crisanto Calos said...
Sir nathan pdw b makakuha sau ng sample sa pag wiring ng full wave RR sa wiring ng fury 125.
August 20, 2016 at 10:21 AM
Unknown said...
Goodmorning po sir, tanong lang oo sana ako kung the same procedure lang po sa xrm110 ko ? Gusto ko po kasi din
sya convert to fullwave . Salamat po
August 25, 2016 at 6:43 PM
Mike Sandoval said...
This comment has been removed by the author.
November 17, 2016 at 2:46 AM
Mike Sandoval said...
Sir nafullwave mo na ba fury mo?
November 17, 2016 at 2:47 AM
Mike Sandoval said...
Gudday sir nathaniel...same lang ba ang wiring ng fury sa ibang mc like xrm125 o kahit 125cc?..TIA sir..
November 17, 2016 at 2:49 AM
masther said...
anung pwedeng gawin pag naddrop ang boltahe ng below 12v kapag nka hid? ang stock ng stator ay nka full wave na
at ang r/r ng motor ay 5 wires. 35 watts yung hid. motor ko is motorstar nicess 110.
November 30, 2016 at 7:46 AM
Gian Garnace said...
san po bang mekaniko pwede mag pa full wave dito sa paranaque? yung quality po sana.
December 1, 2016 at 6:12 AM
Post a Comment
Newer Post
Home
Older Post
Copyright 20162016 Techy at day, Blogger at noon, and a Hobbyist at night | Powered by Blogger
Design by NewWpThemes | Blogger Theme by Lasantha - Best Blogger Themes | Thanks NewBloggerThemes.com