You are on page 1of 7

FAS

Power
reduces labor costs up to 50%
Easy to order Easier to install
If you are constructing a hospital, condominium
complex, office building or hotel and the wiring
project is substantial or repetitive, look to FAS Power
products from Legrand/Cablofil. With FAS Power,
much of the electrical assembly is completed in
advance, dramatically cutting project completion
times and saving a minimum of 50% in labor costs.
With FAS Power, all of the device choices that you
have with standard construction are available, but
with the installation ease and labor savings of a prefabricated electrical assembly. Choose from Pass &
Seymour PlugTail outlets and switches or our full
line of pre-installed devices. You can also specify
per-cut lengths of MC cable to be pre-wired into
each assembly further reducing installation time.
FAS Power will speed up the rough-in phase of your
project and inspections will never be easier because
every assembly is UL or ETL listed.

200

introduction

introduction

Setting up the initial order is also made easy with our online
configurator that helps you design and specify the precise parts
you need. You can find it on our website at www.faspower.com.

www.legrand.us/cablofil 201

FAS Power Pre-fabricated


Wiring Assemblies

Rough-in is fast and easy with FAS Power. Pre-fabricated floor brackets slide under the
sill plate with no vertical measuring needed. Wall brackets with pre-mounted boxes
and rings quickly attach to the stud with switches and switch/outlet combinations in
place. And all assemblies can be pre-wired for fast installation with Pass & Seymour
PlugTail outlets and switches connected to Southwire MCAP branch circuit wiring using
push connector hardware. Assemblies can then be connected to a homerun enclosure
mounted to a Cablofil cable pathway. And for fast job starts, FAS Power products are
prepackaged and shipped to the requirements of the contractor.

Pre-wired
with Pass
& Seymour
PlugTail.

Each FAS Power assembly includes:


Floor or wall bracket with one to four gang openings
Pre-installed boxes
Pre-installed plaster rings are available in 1/2 to 2 raise or
adjustable style
Far side support arms
PlugTail or standard devices can be pre-wired to MCAP cable or
packaged separately
CJ6 wire manager

FAS Power can benefit you in many ways:


Fast job starts FAS Power is packaged and
shipped per contractor instructions
Reduced rough-in time Boxes are pre-mounted
and grounded
Pre-installed plaster rings can be specified to
fit any wall thickness
Pre-wired to MC cable FAS Power assemblies can be pre-wired
to pre-cut MCAP cable lengths

Painless inspections All assemblies are UL or ETL listed


Faster finishes with pre-wired assemblies, just install your
PlugTail outlet/switch or remove the cover from pre-installed
devices

FAS Power now


offers PlugTail
switches from
Pass & Seymour.

Connect to home runs


supported by Cablofil Tray.

introduction

introduction

Wide variety of device choices PlugTail allows you to make device


choices at finish or devices can be pre-installed and protected
during drywall installation

All products contained within this brochure are either UL or ETL listed.
202

www.legrand.us/cablofil 203

FAS Power Pre-fabricated Wiring Assemblies

Floor Bracket Wired Assemblies 1 to 4 Openings

The FAS Power Floor Bracket Wired Assembly consists of a

in every FAS Power product, including P&S PlugTail wiring

floor bracket, 4 rings, back side support arm, 4 /16 x 2 /8

devices and Southwire MCAP metallic clad cabling.

11

DOUBLE OPENING FLOOR BRACKET

TM

boxes and devices that are pre-wired to precut MC cable.


All pre-installed outlets and PlugTail devices are shielded

Installation: The floor bracket is quickly installed by

in plastic to keep them finish ready during the taping and

kicking the lower flange under the wall base then securing

painting process. The boxes are mounted independent of the

with screws using predrilled holes in the bracket. At finish,

rings to allow the devices to be used for in-line or multi-wire

PlugTail allows you to quickly connect to a wide choice of

branch circuits. Legrand /Cablofil uses quality components

P&S devices in a variety of colors.

CF218 - RPT - 058 - 350 - MC122 - 1

back side
support arm

4 ring

4 11/16 x 2 1/8
Box

SINGLE OPENING FLOOR BRACKET

pushwire
connectors

back side
support arm

box
mounting
height

4 ring
floor bracket

single gang
receptacle
(Not Included)

single gang
receptacle
(Not Included)

4 11/16 x 2 1/8 Box

pushwire
connectors

FOUR OPENING FLOOR BRACKET

THREE OPENING FLOOR BRACKET

TR

HG

box
mounting
height

204

single opening floor bracket catalog numbering example:

CF1 18
Bracket Type
CF1 Floor Bracket,

Wired with Pushwire


Connectors, (1) Opening

Floor Brackets are


available with 1 thru 4
openings

Box
Mounting
Height
Box mounting
heights are
available at 12,
15, 18 and 24

RPT

058

TR

Wiring
Components

Ring

See a complete
list of options on
page 213

See a complete
list of options on
page 213

350

MC122

Back Side
Arm Support

See a complete
list of options on
page 213

HG

box
mounting
height

box
mounting
height

MC Cable

single gang
receptacle
(Not Included)

(First, Second, Third,


Fourth Opening)
See a complete
list of options on
page 213

CF318 - PRT - D - D - 350 - MC122 - 1

CF418 - RPT - D - 0 - D - 058 - 350 - MC122 - 1

For a comprehensive list of floor bracket wiring assembly options, use our handy configurator at www.legrand.us/cablofil.
TR

HG

TR

f l o o r & w a l l b rx xa cx kx ex t a s s Y .

f l o o r &x xwxaxlxl b r a c k e t a s s Y .

floor bracket

single gang
receptacle
(Not Included)

www.legrand.us/cablofil 205
HG

FAS Power Pre-fabricated Wiring Assemblies

Wall Bracket Wiring Assemblies 1 to 4 Openings

The FAS Power Wall Bracket Wired Assembly consists of a

uses quality components in every FAS Power product,

wall bracket, 4 rings, back side support arm, 4 /16 x 2 /8

including P&S PlugTail wiring devices and Southwire

boxes and devices that are pre-wired to precut MC cable.

MCAP metallic clad cabling.

11

DOUBLE OPENING WALL BRACKET WIRED ASSEMBLY


WITH SINGLE GANG ADJUSTABLE RING

THREE OPENING WALL BRACKET WIRED ASSEMBLY

TM

All pre-installed outlets, switches and PlugTail devices


are shielded in plastic to keep them finish ready during

Installation: The wall bracket is quickly installed with

the taping and painting process. The boxes are mounted

screws using predrilled holes in the bracket. At finish,

independent of the rings to allow the devices to be used

PlugTail allows you to quickly connect to a wide choice

for in-line or multi-wire branch circuits. Legrand /Cablofil

of Pass & Seymour devices in a variety of colors.

16

91/2

SINGLE OPENING WALL BRACKET WIRED ASSEMBLY

4 ring
wall bracket

4 11/16 x 2 1/8 Box

plugtail
back side
support arm

cw2 - 0 - spt - APR1 - 350 - mc202

single pole
switches
(Not Included)

SS

FOUR OPENING WALL BRACKET WIRED ASSEMBLY

cw3 - SGPT - 0 - 0 - 058- 350 - mc122 / mc122-1

GFI

3/4 GANG WALL BRACKET WIRED ASSEMBLY

pushwire
connectors
26

26

91/2

206

single opening WALL bracket catalog numbering example:

Cw1
Bracket Type
CF1 Floor Bracket,

Wired with Pushwire


Connectors, (1) Opening

Wall Brackets are


available with 1 thru 4
openings

- SS P T

- 058

- 350

MC202/MC202-1

Wiring
Components

Plaster
Ring

Back Side
Arm Support

See a complete
list of options on
page 213

See a complete
list of options on
page 213

See a complete
list of options on
page 213

For a comprehensive list of wall bracket wiring assembly options, use our handy configurator at www.legrand.us/cablofil.

MC Cable
(First, Second, Third,
Fourth Opening)
See a complete
list of options on
page 213

cw4 - 0 - J - 058 - 350

cw34 - SSSPT - 058 - 350

SSS

f l o o r & wa l l b r a c k e t a s s Y.

f l o o r & wa l l b r a c k e t a s s Y.

SS

www.legrand.us/cablofil 207

FAS Power Pre-fabricated Wiring Assemblies


Floor & Wall Brackets

The Floor Bracket is the centerpiece of our product line and represents

The Wall Bracket offers unsurpassed versatility for the installation of electrical boxes

FLOOR BRACKETS

the latest innovation by our Wiring Systems. The patented design permits

PRODUCT NO. (EA)

GANG

CENTER
HEIGHT

F112

12

the bracket. Accepts 4 and 5 rings, and 4 and 4 11/16 x 2 1/8 boxes mounted horizontally

F115

15

or vertically.

F118

18

Wall Brackets: 18 gage galvanized steel.

horizontally or vertically.

F124

24

Support Arms: Attach to the back of the Wall Bracket to support the assembly against the

Floor Brackets: 16 gage galvanized steel.

F212

12

wall behind. No attachment hardware is required. Purchased separately.

F215

15

assembly against the wall behind. No attachment hardware is required.

F218

18

Purchased separately.

F224

24

F312

12

F315

15

F318

18

F324

24

F412

12

F415

15

F418

18

F424

24

fast installation anywhere between studs and ensures correct device


mounting height with no measuring required.
Installation: The Floor Bracket is installed by kicking the lower flange
under the wall base. Two holes are provided for attachment screws if
needed. Accepts 4 and 5 rings, and 4 and 4 /16 x 2 /8 boxes mounted
11

Support Arms: Attach to the back of the Floor Bracket to support the

Keyhole openings allow 4 or 4 11/16 x 2 1/8 boxes to


remain attached.
Support Arms (purchased separately) are attached to
the back of the Bracket using the two slots provided.
Attachment Holes for 4 Rings allows 4 11/16 x 2 1/8
Boxes to be mounted independently.
Attachment Holes for 4 11/16 x 2 1/8 Boxes allow 4
Rings to be mounted independently.

Note: Floor brackets are available without


CJ6 by adding an N to the end
of the catalog number. ( Example: F118-N )

floor & wall br acke ts

W2

W3

W4

W34

W16SL

16 Slider

W24SL

24 Slider

Attachment Holes for 4 Rings allow 4 11/16 x 2 1/8 boxes


to be mounted.

91/2
WI

W2

16
W3

W24SL

W16SL

6
24

16

16

24

5
26
W4

26
W34

floor & wall br acke ts

208

F4

Support Arms (purchased separately) are attached to


the back of the Bracket using the two slots provided.

5
F3

W1

Keyhole openings allow boxes to remain attached to


the Bracket when the rings are removed.

16

F2

GANG

Wall Bracket attachment holes

11

FI

PRODUCT NO. (EA)

Installation: The Wall Bracket is quickly installed with screws using the holes provided in

center
height

wall BRACKETS

anywhere between studs at any height.

www.legrand.us/cablofil 209

FAS Power Pre-fabricated Wiring Assemblies


Accessories Covers

Adjustable Rings, Support Arms & Pushwire Connectors

Metal Device Covers attach to the front

adjustable rings

of receptacles and switches to protect


DC-1

from possible damage caused by drywall

PRODUCT NO. (EA)

DEVICE TYPE

apr-1-5/8

single gang

apr-1

single gang

apr-2

two gang

installation or painting. For use on


Standard, Decorator and Toggle-type

APR-1

APR-2

APR-3

APR-R

devices.

raise
/8 TO 11/4

/4 TO 11/2
/8 TO 11/2

Material: Covers are galvanized steel.

Adjustable Rings are useful in installation where wall thicknesses are

APR-3

three gang

/4 TO 11/2

Hardware is zinc-plated steel.

unknown at the time of order or electrical rough in.

apr-R

3-0 round

/4 TO 11/2

Material: Galvanized steel.


metal device covers

Pushwire Connectors make the job of

DEVICE TYPE

FASTENERS
included

dc-1

single gang

(2) #8-32 screws

than ever before. Simply strip the wire, insert

PRODUCT NO. (EA)

GANG

COLOR

dc-2

two gang

(4) #8-32 screws

the conductor into the connector and you have

PC-2-YL

YELLOW

a solid connection. The clear housing allows

PC-4-OR

ORANGE

for visual inspection to ensure the proper

PC-6-PL

PURPLE

connection of stranded or solid conductors.

PC-8-GY

GRAY

Integrated test ports allow for circuit testing

PC-6-GR

GREEN

under an energized condition.

PC-8-GR

GREEN

connecting wires easier and more reliable

AR-350

DC-2
Support Arms attach
to the back of Floor,
Plastic Device Covers attach to the front of receptacles,
switches or can be snapped onto empty mud rings to keep them
clean, dust free and finish ready during the taping and painting
process. The covers are replaced later with faceplates at the

DCP-2

trim out phase of construction.

DCP-3R

Brackets to support the


assembly against the

Wire Size Range


16-12 AWG Copper Solid Conductors
18-12 AWG Copper Stranded Conductors

PC-2-YL
PC-4-OR

wall behind the devices.

PC-6-GR

No attachment hardware
Material: Zinc-plated

PRODUCT
NO. (EA)

box size / DEVICE TYPE

FASTENERS
included

DCP-1

Single gang receptacle

(2) #8-32 screws

DCP-2

Double gang receptacle

(2) #8-32 screws

DCP-3

three gang receptacle

(2) #8-32 screws

DCP-4

four gang receptacle

(2) #8-32 screws

DCP-1T

Single gang toggle switch

(2) #8-32 screws

DCP-2T

Double gang toggle switch

(2) #8-32 screws

DCP-3T

Three gang toggle switch

(2) #8-32 screws

DCP-4T

Four gang toggle switch

(2) #8-32 screws

DCP-DT

DBL. gang toggle switch & device

(2) #8-32 screws

DCP-1R

Single gang plaster ring only

None

DCP-2R

Double gang plaster ring only

None

DCP-3R

Three gang plaster ring only

None

DCP-4R

Four gang plaster ring only

None

DCP-R

3" Round plaster ring only

None

steel.
SUPPORT ARMS
PRODUCT NO.
(EA)

WALL
DEPTH

AR-300

AR-350

31/2

AR-400

AR-450

4 /2

AR-500

AR-550

51/2

AR-600

AR-650

61/2

In-sure
PUSHWIRE CONNECTORS
PRODUCT NO. (EA)

GANG

COLOR

In-Sure Push-In Wire Connectors features

PI-42-OR

Orange

an easy-grip design that combined with a low

PI-32-RD

Red

insertion force makes repetitive electrical

PI-33-OR

Orange

connections fast and easy. All In-Sure wire

PI-34-YL

Yellow

connectors accept either stranded or solid


wires and include stainless steel inserts that
restrict pull-out. Built-in check ports allow for
continuity testing.
PI-34-YL

PI-42-OR

PI-32-RD

PI-39-BL

Wire Size Range


20-12 AWG Solid
16-12 AWG Stranded (19 strand or less)
18 AWG Stranded (7 strand)
18-14 AWG Stranded Tin-Bonded
(19 strand or less)
PI-39-BL

Blue

Wire Size Range


14-10 AWG Solid
12-10 AWG Stranded (19 strand or less)
14-10 AWG Stranded Tin-Bonded
(19 strand or less)
All push style connectors used in FAS Power
assemblies conform to these standards:
Voltage Rating:
600 Volts, 1000 Volts for fixtures and signs
Current Rating:
Matches the largest conductor used
Temperature Rating: 105 Degrees C

other accessories

other accessories

DCP-1T

Wall, and Universal

is required.

plastic device covers

210

PUSHWIRE CONNECTORS

PRODUCT
NO. (EA)

www.legrand.us/cablofil 211

FAS Power Pre-fabricated Wiring Assemblies


Wire & Connector Accessories

Legrand/Pass & Seymour receptacles


and switches meet the demands of any
commercial project.
Almost any device can be specified and pre-wired into FAS Power
assemblies including GFCI, HCF and Tamper-Resistant devices. All devices
are available in standard or decorator styles and 15 to 20 amp options. And
every installed device is protected with a plastic shield that keeps them
clean, dust free and finish-ready.
Also available is P&S PlugTail the fastest, most consistent and reliable
device installation ever. At rough-in, install the pre-stripped leads of a
PlugTail connector instead of pigtails. With no exposed terminals the
circuit can be powered up and tested at any time.
At finish, select from a wide array of color choices for the specified device,
click in the connector and tighten the mounting screws installation takes
less than a minute. PlugTail reduces the chance of mistakes leading to
callbacks and eliminates missed deadlines with most of the labor savings
realized at the end of the job.
For more information about Pass & Seymour products,
go to www.passandseymour.com.

FAS Power Components


OUTLETS

FAS Power prewired assemblies can specified with any length of MC cable
up to 99 feet in stranded or solid conductor types. IG and HCF versions are
also available. Type MC cable can be used anywhere Type MC or AC cable is
permitted.

050

raise

RPT

PlugTail for Duplex Outlet

058

RR

2 Duplex Outlets

075

raise

wire & connector accessories


212

For more information about Southwire cabling products,


go to www.southwire.com.

/8 raise

PlugTail for 2 Duplex Outlets

100

1 raise

Tamper Resistant Duplex Outlet

125

1 1/4 raise

RTRPT

PlugTail for Tamper Resistant Duplex Outlet

150

1 1/2 raise

RRTR

2 Tamper Resistant Duplex Outlets

PlugTail for 2 Tamper Resistant Duplex Outlets

200

2 raise

Hospital Grade Duplex Outlet

APR

Adjustable

RHGPT

PlugTail for Hospital Grade Duplex Outlet

RRHG

2 Hospital Grade Duplex Outlets

PlugTail for 2 Hospital Grade Duplex Outlets

250

Duplex Outlet - Half Hot

300

3 wall depth

PlugTail for Duplex Outlet - Half Hot

350

3 wall depth

RRPT
RTR

RRTRPT
RHG

RRHGPT
R/SL
R/SLPT

BACK SIDE ARM SUPPORT


2 wall depth

Duplex GFCI Outlet

400

4 wall depth

GPT

PlugTail for Duplex GFCI Outlet

450

4 wall depth

GG

2 Duplex GFCI Oulets

500

5 wall depth

PlugTail for 2 Duplex GFCI Oulets

550

5 wall depth

Tamper Resistant Duplex GFCI Outlet

600

6 wall depth

PlugTail for Tamper Resistant Duplex GFCI Outlet

Hospital Grade Duplex GFCI Outlet

PlugTail for Hospital Grade Duplex GFCI Outlet

1 Single Pole & Duplex GFCI Outlet

Stranded

PlugTail for 1 Single Pole & Duplex GFCI Outlet

Solid

GGPT
GTR
GTRPT
GHG
GHGPT
SG
SGPT

MC CABLE type

hcf Stranded

Isolated Ground Duplex Outlet

RIGPT

PlugTail for Isolated Ground Duplex Outlet

hcf Solid

RRIG

2 Isolated Ground Duplex Outlets

Stranded ap

PlugTail for 2 Isolated Ground Duplex Outlets

Solid ap

RIG

hcf Stranded ap

SWITCHES
S
SPT
S3
S3PT
SS

Single-Pole Switch

PlugTail for Single-Pole Switch

Three-Way Switch

PlugTail for Three-Way Switch

2 Single-Pole Switches

12/4

ig Solid

S3S3

2 Three-Way Switches

PlugTail for 2 Three-Way Switches

1 Single Pole and 1 Three-Way Switch

PlugTail for 1 Single Pole and 1 Three-Way Switch

1 Gang Ring and 4 Box

1 Gang Ring and 4 Box with Ground Pigtail

2 Gang Ring and 4 Box

SS3PT

12/3

ig Stranded

PlugTail for 2 Single-Pole Switches

SS3

12/2

hcf Solid ap

SSPT
S3S3PT

conductors

MC CABLE
D
DGP
DD

2 Gang Ring and 4 Box with Ground Pigtail

1 Gang Ring Only

TT

2 Gang Ring Only

Junction Box

DDGP

J
4S0

4 Box Only

5S0

5 Box Only

wire & connector accessories

For additional labor savings consider using Southwire MC . UL and


NEC compliant, its patented design eliminates the need for anti-short
bushings, separate ground-wire terminations and paper covering removal
from each conductor. MCAP all purpose cable speeds branch circuit
make-up by up to 30% while providing a 350% better ground continuity
plan. For health care applications HFC MCAP is also available.
AP

PLASTER RINGs

RRIGPT

Using MC cable with FAS Power helps you


gain a competitive advantage on every job.

Wall Floor
Duplex Outlet

www.legrand.us/cablofil 213

You might also like