‘Rerum o Table of Coes
en
Pee AISC Specfcation Appendix 7, Section 733.2, the reguited stengbs are determined ffom a firsterder
gals ang uctioal Loads detesmized below along wath 3; smluplie as detesmsed fom Appenats 8.
For ASD, do aot mig loads or devi rms by 16.
Frame Anebsis Gravity Loads
‘The waifoom gravity londs to be considered inthe ft-nder alps onthe beam from B tC are
TEED
aD,
een
aint
djcent beams ae:
CCoaceatsted gravity load to be considered ina cecond order analysis onthe cola at B aad C coatibued by
TEED)
F=(S0RC IEDR)
6.0 ps
Frame Anata: Nononal Loads
‘pplication of aoGoual loads
Pee AISC Specficanon Appendor 7, Sestion 732, Same ontofphimbaess ast he aceuated for by the
From AISC Spectfeanon Appesdix Eeuatoa A.7-2, te sequreé aotona leads ae:
tacayrx 000207;
=2:1(1.0(0 0240 in 088 Kips)
ta(atyrx 0.00827;
=21(1 640 0/240 in 182 aps)
2 00082088 ke) 20.00820192 kgs)
10 igs > 12 Kips Dips O80 ps
121 Bp 0.505 kige
sagas ane oF EEEReam Tele of Contents
ca
Sura ped Frome oaks
TD co
.0Mbs 2st 20s moth
asonpn sown
121 one
tes ve
er AISC Sefton Ape, Sechon 722 cod! ie mi ie ion ie
“ng aise owing andere
TD, zr
a Tore
coe Dae tae et
ae yo | ae spe
fs te
rhs raships «73 ‘sh
Ces the senmiption ha the sto ofthe second ordre othe Hit suder dit des act exceed 1.5. Beam be
seed to check this lit Calculate 3; pr the provisions of Section 82 of Appendix 8 ing the els ofthe
=288 Ep:
By -1-013(Fy/Bar)
=1-0.15(14415p5/28813p5)
(Spe. Eg AS)
firtorder analysis
TED ab
Fega Ti Diape TI ips Fig= ATS hope 383 Rips
frre 96 ge
ayy = Lt ips + 46 ips) Finn = 96 ips + 424 ps)
= 192
By 71-015 y /Pay)
=1-0.5(96:p2/1828p5)
(Spe. Eg. AS)
0925 0925
Ay =0250% ay = 0167 a,
B= 0.206 kips
£22018
Desgege 140‘Renunto Table of Contents
cu
35
ect 87 ore £4 A587)
a-—tia emtpasy)| =a oe FA58)
ae ee
Ram Row
—— sy ie
Tao roar
“T0% “oe
aux au0
‘The assumption ta! the tio ofthe maxim second-order eft the masinmn isrder dei no ereter
shan I Si core therefore theft order acalyeie matzed i pated.
(Check the assueticn that ct $0.37; and therefore the fst-eder analysis method is pete,
037y~ 05% ay
0.3030 s)09.1 23)
nai kee
TD a
aH =L0(72 8p) a =16(483 bps)
728 tape <478 kip ote |= 176 tps «478 ape
‘The assumption thet the first-order analysis method canbe weds vesied,
Altaongh the second-order sway multiplier i approsimtely 14, the chaage ix beading scment i small became
‘he oaly sway moments a those produced bythe small astosal loads. For loa combizations With siauScaat
gravity and Inter loadings, the crease in bending momeats is large
‘Verify the colons stengts using the eecond-oner faces, sing the ftlowing effective engi (calculations not
bow:
Cotas
‘Uae KZ,= 2008
Use kL ~ 2008
Deis Benge V4
ANEL.CAS BETTIE OF STEEL CONTTBUCTIN