Professional Documents
Culture Documents
0_CH_EN
ANTA
ANTB
ANTA ANTB
NODEA NODEB
NODEB PE
NODEA
RX:814~834MHz TX:859~879MHz
Band: RX: 814 - 834 MHz TX: 859 - 879 MHz
1.2 Installing the Filter on the Wall
2.
1.
1 2
3
1. 2./ 3.
1. Mounting Bracket 2. Pole-mounting Bracket (back/front) 3. Long Bolts
1. /
1. Put the four long bolts through spring washers, flat washers, the mounting bracket, the front and back
pole-mounting brackets and screw them up to fasten the mounting bracket on the pole.
2.
3 4
2. Fit the hangers on both sides of the filter into the gaps on the upper side of the mounting bracket.
3. Use four screws on each side to fasten the filter on the mounting bracket.
1.4 Connecting the Cables to the Filter
1.4.1 Overview
ANT
ANTA ANTB
NODEA NODEB 3
ANT1 ANT4
TX/RX TX/RX
SN Cable Function
1 RF Jumper ANTA/ANTB
Connecting the ANTA/ANTB port of the filter to the RF port of the antenna
2 RF Jumper NODEA/NODEB RRU
Connecting the ANTA/ANTB port of the filter to the TX/RX port of the RRU
3 Grounding Cable PE
Connecting the PE terminal of the filter to an outdoor grounding busbar
1. R8862A
2.1+3+3
3. RRU
Note:
1. The RF port of R8862A is waterproofed with a cold-shrinkable tube.
2.The joints of other RF jumpers are waterproofed with the 1+3+3 method (that is, one layer of one-layer
insulation tape, three-layer waterproof tape, and three-layer ultraviolet-proof tape)
3.The metal covers of the idle RF ports of the RRU should be screwed up.
1.4.2 Cable Connections
1. PE
ANT
2
2. +45 -45
NODEA/NODEB RRU TX/RX
3. ANTA/ANTB
1. Connect the PE terminal of the filter to
the outdoor grounding busbar with a
short grounding cable. Note that this 3
ground cable should not exceed 2 m.
2. Connect the NODEA and NODEB ports
to the TX/RX ports of the RRU with RF
ANTA ANTB
jumpers.
3. Connect the ANTA and ANTB ports to
the corresponding RF ports of the
antennas RF jumpers.
NODEA NODEB 1
1. RRU 1/2
5M
2. RRU 2
RRU
Note:
1. If the distance between the RRU and
the antenna is short and they are
directly connected with two 1/2 super
flexible jumpers, it is recommended
that the total length of the two jumpers
not exceed 5 m.
2. For the connections of other cables of
the RRU, refer to related installation ANT1 ANT4
manual. TX/RX TX/RX
2 AISG AISG Cable Connection
2.1 RRU 20m Distance between the RRU and the Antenna
Is Less Than 20 m
HWXX-6516DS1-VTM
L-1710-2690MHz R-1710-2690MHz
1.AISG AISG 1
1
Cable
AISG/EAM
R8964
LDXX-6515DS-VTM
790-960MHz 790-960MHz
1. AISG 2
AISG Adapter 2
Cable
2. AISG AISG
Cable 1
R8862A
2.2 RRU 20m Distance between the RRU and the Antenna Is
Greater Than 20 m
ANT
1
ASBT
NSBT
3
1
AISG/EAM
ANT1
R8964
ANT
1
ASBT
NODEA NODEB
AISG/MON
ANT1 ANT4
TX/RX TX/RX
R8862A
2.3 AISG Cascading AISG RCUs
2.3.1 6-Channel Antenna
A
N
T
R8862A R8964
R8862A
R8964
AISG/MON
AISG/EAM
Note: For the connections of the RETs to the RRUs, refer to the identities on the
antennas.
2.3.2 Four-Channel Antenna
ANT
R8964
R8964
AISG/EAM
2.3.3 AISG AISG-Related Cables
AISG
AISG Cable
AISG R8862A
AISG Adapter Cable (applicable to R8862A)
3 Antenna System Connection
3.1 FTL FTL Multi-Mode
3.1.1 FDD/TDD RRU 20m Distance between FDD/TDD RRU and
Antenna Is Not More Than 20 m
CVV65CSX-M
L-1710-2690MHz R-1710-2690MHz 790-960MHz
2
1
2 ANTA ANTB
1
NODEA NODEB
1
3
AISG/EAM
R8964 R8862A
CVV65CSX-M
L-1710-2690MHz R-1710-2690MHz 790-960MHz
3
3
ASBT
3
1
2
AISG/EAM
NSBT
R8964
ANTA ANTB
NODEA NODEB
4
1
ANT1 ANT4
TX/RX TX/RX
R8862A
CVV65CSX-M
L-1710-2690MHz R-1710-2690MHz 790-960MHz
3
3 3
1
ASBT
ASBT
2 NSBT
ANTA ANTB
NODEA NODEB
NSBT
3
1 1
4
AISG/EAM
R8862A
HWXX-6516DS1-VTM
L-1710-2690MHz R-1710-2690MHz
1
2
AISG/EAM
R8964
1.1/2 2.AISG
1. 1/2 Jumper 2. AISG Cable
3.2.2 TDD RRU 20m Distance between TDD RRU and Antenna Is
Greater Than 20 m
HWXX-6516DS1-VTM
L-1710-2690MHz R-1710-2690MHz
3 1
ASBT
NSBT
3
1
AISG/EAM
R8964
LDXX-6515DS-VTM
790-960MHz 790-960MHz
3
1 1
3 ANTA ANTB
NODEA NODEB
1
2 1
R8862A
1.1/2 2. AISG 3.AISG
1. 1/2 Jumper 2. AISG Adapter Cable 3. AISG Cable
3.3.2 FDD RRU 20m,AISG Distance between FDD RRU and Antenna
(with RCU) Is Greater Than 20 m
LDXX-6515DS-VTM
790-960MHz 790-960MHz
1
4 1
ASBT 4
2 2
NSBT
ANTA ANTB
3 NODEA NODEB
1
1
R8862A
LDXX-6515DS-VTM
790-960MHz 790-960MHz
1 1
ANTA ANTB
NODEA NODEB
1
1
R8862A
1.1/2
1. 1/2 Jumper
3.3.4 FDD RRU 20m Distance between FDD RRU and Antenna Is
Greater Than 20 m
LDXX-6515DS-VTM
790-960MHz 790-960MHz
1 1
2 2
ANTA ANTB
NODEA NODEB
1
1
R8862A
CMAX-DM30-CPUSEi
790-960MHz
+45 -45
ANTA ANTB
NODEA NODEB
ANT1 ANT4
TX/RX TX/RX
R8862A
1.1/2
1. 1/2 Jumper
3.4.2 FDD RRU 20m Distance between FDD RRU and Antenna Is
Greater Than 20 m
CMAX-DM30-CPUSEi
790-960MHz
+45 -45
ANTA ANTB
NODEA NODEB
ANT1 ANT4
TX/RX TX/RX
R8862A
1.1/2 2. 7/8
1. 1/2 Jumper 2. 7/8 Feeder
CL
518057
http://dms.zte.com.cn
075526770800 800-830-1118
075526770801
* * * *
Planned by: CL Product Support Dept
Prepared by: Zhang Mao
Translated by: Huang Daowen
ZTE Corporation
Address: ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China
Post code: 518057
Technical support website: http://dms.zte.com.cn
Hotline: 86-755-26770800 or 800-830-1118
Fax No.: 86-755-26770801