Professional Documents
Culture Documents
Features
Modular pluggable technology, easy tool onsite maintenance;
Honeycomb briquette burning effect and the whole structure cooling
technology;
Double-coupling IP68 protection, highest waterproof level;
Intelligent constant current driving technology, long life span;
Ergonomic light distribution to achieve uniform illuminating effect;
Free modular serialization and full power range solution.
Applications
Facade and building lighting
Factory lighting
Area & Storage lighting
Parking Lot
Standard Colors
Black
Gray
Advantages
70
AC100-240 700 160 110 5 17600800 25 Lumileds 4000
0.95 91% 40
FL2C-4 50/60 860 200 105 5 210001000 40 5000
60
1050 240 100 5 240001200 60 5700
90
700 200 110 5 220001000 90
110
FL2C-5 860 250 105 5 262501250 110
~+50,
FL2C-3 360*260*255 430*335*330 5.6 6.6
-40
~+50 Aluminum
IP68 Schematic
FL2C-4 -40 >50,000 360*260*335 475*430*210 6.7 8
10%~90%RH. Power Alloy below on
FL2C-5 360*360*415 615*430*210 8.4 9.9
Supply IP67 Dimensions
FL2C-6 360*360*495 660*430*210 9.4 11.1
Warranty
5-year limited warranty is standard on luminaire and components.
Specifications
Flood Light FL2C
FL2C Series
M8B Module
Optical Lens
Multiple light distributions
Adjustable Bolt
Side Beam
360 degree
Aluminum alloy
Mounting Bracket
360adjustable
Driver Cover
Optional
Specifications
Flood Light FL2C
FL2C Series
LED Driver
IP67 rating
Specifications
Flood Light FL2C
FL2C Series
Dimensions
FL2C -1 -2 -3 -4 -5 -6 -7
95mm 175mm 255mm 335mm 415mm 495mm 575mm
L
(3.74) (6.89) (10.04) (13.19) (16.34) (19.49) (22.64)
W 360 mm(14.17)
200 mm 200 mm 260 mm 260 mm 360 mm 360 mm 360 mm
H
(7.87) (7.87) (10.24) (10.24) (14.17) (14.17) (14.17)
Specifications
Flood Light FL2C
FL2C Series
Installation
1. Fix the luminary onto the 2. Connect the ground wire, 3. Loosen the M8x20 screws 4. Installation finished.
mounting surface with two neutral wire and live wire to at bracket joint, adjust the
M10 screws at the bracket. the AC input (make sure it mounting angle. Then
sufficiently grounded). tighten up the screws at
bracket joint
Maintenance
Driver & Electrical Parts
1. Disconnect the luminary 2. Unscrew the screws to 3. Disconnect the connectors 4. Unscrew the screws at the
from AC power. Unscrew the open the back cover. for the driver. ends of the driver set, and
screws to remove the driver replace with a new set.
cover.
5. Fixate the new driver set 6. Connect the new driver to 7. Tighten up the mounting 8. Fix the driver cover back
with the screws and tighten modules and tighten up the screws for the new driver, and tighten up the screws.
up. connectors. surge protector and the
cable clip.
Specifications
Flood Light FL2C
FL2C Series
Module
1.Unscrew the screws on the 2. Unscrew the screws at 3. Plug out the module. 4. Disconnect the failed
main beam covers at both both ends of the failed module from female
sides and remove the two module. connector and replace it
main beam covers. with a new one.
5. Connect and tighten up 6. Install and fixate the 7. Close the main beam
the waterproof connectors. module with the screws. covers on both sides and
tighten up the screws on
them.
Specifications
Flood Light FL2C
FL2C Series
Spin the male terminal clockwise. When the male indicatrix points between indicatrix female #2 and #3, and the gap
between male and female terminals is extremely small, the connectors are well connected; otherwise, there will be risks in
its waterproof performance.
When the gap between male and female terminals is extremely small, if any looseness can be sensed, please spin the male
terminal clockwise until tight.